NCERT Exemplar Solutions Class 12 Physics Chapter 2 Electrostatic Potential and Capacitance

These NCERT Exemplar solutions for Class 12 Physics Chapter 2, Electrostatic Potential and Capacitance, give step-by-step answers to all 33 questions: 6 MCQs, 7 multiple-correct MCQs, 5 very short, 5 short and 10 long answer questions. They cover equipotential surfaces, potential and potential energy of charges and rings, capacitors with dielectrics, sharing of charge between capacitors and conductors, and the zero-potential surface of a pair of charges. Each answer is followed by a short Teacher's Note to build understanding and an Examination Note on how to present the answer for better marks.

Multiple Choice Questions (MCQs)

Question 1: A capacitor of 4 µF is connected as shown in the circuit. The internal resistance of the battery is 0.5 Ω. The amount of charge on the capacitor plates will be
4Fµ10Ω2.5 V2Ω (a) 0
(b) 4 µC
(c) 16 µC
(d) 8 µC
Show Answer & Explanation

Answer: (d) 8 µC

Explanation:
1. No steady current flows through the branch containing the capacitor and the 10 Ω resistor, so there is no potential drop across the 10 Ω resistor.
2. The battery (emf 2.5 V, internal resistance 0.5 Ω) drives a current through the 2 Ω resistor: \( I = \dfrac{2.5}{2+0.5} = 1\ \text{A} \).
3. Potential difference across the 2 Ω resistor: V = IR = 1 × 2 = 2 V. The capacitor branch is in parallel with it, so the capacitor also has 2 V across it.
4. \( q = CV = 4\ \mu\text{F}\times 2\ \text{V} = 8\ \mu\text{C} \).

Teacher's Note:
1. In steady state a capacitor carries no current, so the resistor in series with it has no voltage across it.
2. The voltage across the capacitor is the terminal voltage of the battery, not its emf, because of the internal resistance.

Examination Note: Use the terminal voltage (emf minus I r) as the voltage across the capacitor; using 2.5 V gives the wrong value 10 µC.

 

Question 2: A positively charged particle is released from rest in a uniform electric field. The electric potential energy of the charge
(a) remains a constant because the electric field is uniform
(b) increases because the charge moves along the electric field
(c) decreases because the charge moves along the electric field
(d) decreases because the charge moves opposite to the electric field
Show Answer & Explanation

Answer: (c) decreases because the charge moves along the electric field

Explanation:
1. A positive charge experiences a force along the electric field, so it moves along the field, from high potential to low potential.
2. The field does positive work on it, so its kinetic energy increases and its potential energy decreases.

Teacher's Note:
1. Field lines point from high to low potential; a positive charge follows them 'downhill'.
2. Potential energy is q V, so moving to lower V lowers the potential energy of a positive charge.

Examination Note: State the direction of motion and the sign of the work done by the field; the decrease in potential energy follows.

 

Question 3: The figure shows some equipotential lines distributed in space. A charged object is moved from point A to point B.
AB10V20V30V40V50VAB20V30V40V50V10VAB10V30V50V20V40VFig.(i)Fig.(ii)Fig.(iii) (a) The work done in Fig. (i) is the greatest
(b) The work done in Fig. (ii) is least
(c) The work done is the same in Fig. (i), Fig. (ii) and Fig. (iii)
(d) The work done in Fig. (iii) is greater than Fig. (ii) but equal to that in Fig. (i)
Show Answer & Explanation

Answer: (c) The work done is the same in Fig. (i), Fig. (ii) and Fig. (iii)

Explanation:
1. Work done by the field in moving a charge q from A to B is \( W = q\,(V_B - V_A) \); it depends only on the end potentials.
2. In all three figures A lies on the 20 V line and B on the 40 V line, and the same charge is moved. So the work is the same in every figure, however the lines are spaced.

Teacher's Note:
1. The spacing of equipotential lines tells how strong the field is, but the work depends only on the potential difference between the end points.
2. Read the potentials of A and B from the figure before comparing anything.

Examination Note: Write W = q(VB − VA), read the two potentials for each figure, and state that they are equal.

 

Question 4: The electrostatic potential on the surface of a charged conducting sphere is 100 V. Two statements are made in this regard. S1: at any point inside the sphere, electric intensity is zero. S2: at any point inside the sphere, the electrostatic potential is 100 V. Which of the following is a correct statement?
(a) S1 is true but S2 is false
(b) Both S1 and S2 are false
(c) S1 is true, S2 is also true and S1 is the cause of S2
(d) S1 is true, S2 is also true but the statements are independent
Show Answer & Explanation

Answer: (c) S1 is true, S2 is also true and S1 is the cause of S2

Explanation:
1. Inside a charged conductor the electric field is zero, so S1 is true.
2. Since \( E = -\dfrac{dV}{dr} = 0 \), the potential does not change inside; it equals its value on the surface, 100 V. So S2 is true, and it follows from S1.

Teacher's Note:
1. Zero field means constant potential, not zero potential.
2. The converse is not true: V = 0 does not imply E = 0 (for example, on the perpendicular bisector of a dipole).

Examination Note: Connect the two statements by E = −dV/dr: zero field implies constant potential.

 

Question 5: Equipotentials at a great distance from a collection of charges whose total sum is not zero are approximately
(a) spheres
(b) planes
(c) paraboloids
(d) ellipsoids
Show Answer & Explanation

Answer: (a) spheres

Explanation:
1. Far from the collection, the charges look like a single point charge equal to the total charge.
2. The potential of a point charge, \( V = \dfrac{q}{4\pi\varepsilon_0 r} \), is the same at all points at the same distance r, so the equipotential surfaces are spheres.

Teacher's Note:
1. The details of how the charges are arranged matter only close to them.
2. For a total charge of zero the far field is that of a dipole and the equipotentials are no longer spheres.

Examination Note: Say that from far away the system behaves like a point charge, then give V = kq/r.

 

Question 6: A parallel plate capacitor is made of two dielectric blocks in series. One of the blocks has thickness d1 and dielectric constant K1 and the other has thickness d2 and dielectric constant K2 as shown in the figure. This arrangement can be thought as a dielectric slab of thickness d (= d1 + d2) and effective dielectric constant K. The K is
d2d1K1K2 (a) \( \dfrac{K_1d_1+K_2d_2}{d_1+d_2} \)
(b) \( \dfrac{K_1d_1+K_2d_2}{K_1+K_2} \)
(c) \( \dfrac{K_1K_2(d_1+d_2)}{K_1d_2+K_2d_1} \)
(d) \( \dfrac{2K_1K_2}{K_1+K_2} \)
Show Answer & Explanation

Answer: (c) \( \dfrac{K_1K_2(d_1+d_2)}{K_1d_2+K_2d_1} \)

Explanation:
1. The two blocks form two capacitors in series: \( C_1 = \dfrac{K_1\varepsilon_0A}{d_1} \) and \( C_2 = \dfrac{K_2\varepsilon_0A}{d_2} \).
2. \( C = \dfrac{C_1C_2}{C_1+C_2} = \dfrac{K_1K_2\,\varepsilon_0A}{K_1d_2+K_2d_1} \).
3. For the equivalent single slab, \( C = \dfrac{K\varepsilon_0A}{d_1+d_2} \). Comparing, \( K = \dfrac{K_1K_2(d_1+d_2)}{K_1d_2+K_2d_1} \).

Teacher's Note:
1. Dielectric layers placed one behind the other (along the field) are in series; side by side they are in parallel.
2. Check: for K1 = K2 = K0 the formula gives K = K0, as it should.

Examination Note: Derive C from the series formula and compare with Kε0A/d; always test the final expression with K1 = K2.

 

Multiple Choice Questions (More Than One Option)

Question 7: Consider a uniform electric field in the \( \hat z \)-direction. The potential is a constant
(a) in all space
(b) for any x for a given z
(c) for any y for a given z
(d) on the x-y plane for a given z
Show Answer & Explanation

Answer: (b) for any x for a given z, (c) for any y for a given z, (d) on the x-y plane for a given z

Explanation:
1. The electric field points along z, so the potential changes only with z: \( E_z = -\dfrac{dV}{dz} \).
2. Equipotential surfaces are perpendicular to the field, i.e. planes parallel to the x-y plane. So V is constant for any x or any y at a given z, and on the x-y plane at a given z.
3. V is not constant in all space because it changes with z.

Teacher's Note:
1. Equipotential surfaces are always perpendicular to the field lines.
2. Moving at right angles to the field requires no work.

Examination Note: Say that the field has only a z-component, so V depends on z alone.

 

Question 8: Equipotential surfaces
(a) are closer in regions of large electric fields compared to regions of lower electric fields
(b) will be more crowded near sharp edges of a conductor
(c) will be more crowded near regions of large charge densities
(d) will always be equally spaced
Show Answer & Explanation

Answer: (a) are closer in regions of large electric fields compared to regions of lower electric fields, (b) will be more crowded near sharp edges of a conductor, (c) will be more crowded near regions of large charge densities

Explanation:
1. Since \( E = -\dfrac{dV}{dr} \), a large field means a large change of V over a short distance, so surfaces of equal steps in V lie close together: (a).
2. Near the sharp edges of a conductor and where the surface charge density is large, the field is large, so the surfaces crowd there: (b) and (c).
3. Equal spacing occurs only in a uniform field, so (d) is wrong.

Teacher's Note:
1. Crowded equipotentials mean a strong field, just as crowded field lines do.
2. Surface charge density is largest at sharp points of a conductor.

Examination Note: Link every option to E = −dV/dr: field strength is the potential change per unit distance.

 

Question 9: The work done to move a charge along an equipotential from A to B
(a) cannot be defined as \( -\int_A^B \vec E\cdot d\vec l \)
(b) must be defined as \( -\int_A^B \vec E\cdot d\vec l \)
(c) is zero
(d) can have a non-zero value
Show Answer & Explanation

Answer: (c) is zero

Explanation:
1. The work done in taking a charge q from A to B is \( W = q\,(V_B - V_A) \).
2. On an equipotential VB = VA, so the work is zero. Option (b) is not the general definition of work, because the integral gives the work per unit charge only (it is the potential difference), and here it is also zero.

Teacher's Note:
1. Moving along an equipotential, the displacement is always perpendicular to the field, so \( \vec E\cdot d\vec l = 0 \).
2. Work per unit charge equals the potential difference; work itself is q times that.

Examination Note: Use W = q ΔV; it is the shortest route to the result.

 

Question 10: In a region of constant potential
(a) the electric field is uniform
(b) the electric field is zero
(c) there can be no charge inside the region
(d) the electric field shall necessarily change if a charge is placed outside the region
Show Answer & Explanation

Answer: (b) the electric field is zero, (c) there can be no charge inside the region

Explanation:
1. Constant potential means \( E = -\dfrac{dV}{dr} = 0 \), so the field is zero: (b).
2. By Gauss' law, zero field means zero flux through any closed surface inside the region, so there is no charge inside: (c).
3. (a) is not the right description because the field is not just uniform, it is zero. (d) is wrong because the field inside such a region (for example inside a conductor) stays zero even when charges are placed outside.

Teacher's Note:
1. A conductor in equilibrium is an everyday example of a region of constant potential.
2. Zero field does not mean zero potential; the potential only has to be constant.

Examination Note: Write E = −dV/dr = 0 first, then bring in Gauss' law for the charge.

 

Question 11: In the circuit shown in the figure, initially key K1 is closed and key K2 is open. Then K1 is opened and K2 is closed (order is important). [Take Q1′ and Q2′ as charges on C1 and C2 and V1 and V2 as voltage respectively.] Then,
C1C2EK2K1 (a) charge on C1 gets redistributed such that V1 = V2
(b) charge on C1 gets redistributed such that Q1′ = Q2′
(c) charge on C1 gets redistributed such that C1V1 + C2V2 = C1E
(d) charge on C1 gets redistributed such that Q1′ + Q2′ = Q
Show Answer & Explanation

Answer: (a) charge on C1 gets redistributed such that V1 = V2, (c) charge on C1 gets redistributed such that C1V1 + C2V2 = C1E, (d) charge on C1 gets redistributed such that Q1′ + Q2′ = Q

Explanation:
1. With K1 closed, C1 is charged to the emf E, so its charge is Q = C1E. Then K1 is opened, so no charge can leave or enter the system.
2. When K2 is closed the charge is shared until the two capacitors have the same voltage: V1 = V2 (a). By conservation of charge, Q1′ + Q2′ = Q (d).
3. Since Q1′ = C1V1, Q2′ = C2V2 and Q = C1E, option (d) can be written as C1V1 + C2V2 = C1E, which is (c).
4. (b) is wrong because equal voltages give charges in the ratio of the capacitances, which are not equal in general.

Teacher's Note:
1. Two rules decide such problems: equal final voltage across parallel capacitors, and conservation of total charge.
2. Opening K1 before closing K2 keeps the battery out of the redistribution.

Examination Note: Write both rules (V1 = V2 and Q1′ + Q2′ = Q) and then test each option against them.

 

Question 12: If a conductor has a potential V ≠ 0 and there are no charges anywhere else outside, then
(a) there must be charges on the surface or inside itself
(b) there cannot be any charge in the body of the conductor
(c) there must be charges only on the surface
(d) there must be charges inside the surface
Show Answer & Explanation

Answer: (a) there must be charges on the surface or inside itself, (b) there cannot be any charge in the body of the conductor

Explanation:
1. A conductor can have a non-zero potential only if it carries charge, because no other charges are present outside to produce the potential. So there must be charge on the conductor: (a).
2. In electrostatic equilibrium the field inside the material of the conductor is zero, so there can be no charge in the body of the conductor: (b). Any charge sits on its surface.
3. Option (c) is not selected as it is too restrictive (a conductor with a cavity can hold charge on the cavity surface as well), and (d) is false.

Teacher's Note:
1. Excess charge on a conductor stays on its outer surface; the interior is free of net charge.
2. A neutral isolated conductor with no other charges around would have V = 0.

Examination Note: Link the non-zero potential to the presence of charge, and then use the zero field inside to place that charge.

 

Question 13: A parallel plate capacitor is connected to a battery as shown in the figure. Consider two situations. A: Key K is kept closed and plates of capacitors are moved apart using insulating handle. B: Key K is opened and plates of capacitors are moved apart using insulating handle. Choose the correct option(s).
CEK (a) In A Q remains same but C changes
(b) In B V remains same but C changes
(c) In A V remains same and hence Q changes
(d) In B Q remains same and hence V changes
Show Answer & Explanation

Answer: (c) In A V remains same and hence Q changes, (d) In B Q remains same and hence V changes

Explanation:
1. Case A (battery connected): the battery keeps V constant. Moving the plates apart reduces C = Kε0A/d, so Q = CV decreases. Option (c) is correct and (a) is wrong.
2. Case B (battery disconnected): the charge on the isolated plates stays constant. C decreases, so V = Q/C increases. Option (d) is correct and (b) is wrong.

Teacher's Note:
1. Battery connected: V fixed. Battery disconnected: Q fixed.
2. Pulling plates apart (with the battery disconnected) increases the stored energy; the work done by you goes into it.

Examination Note: Begin each case by saying which quantity is held constant (V in A, Q in B).

 

Very Short Answer Type Questions

Question 14. Consider two conducting spheres of radii R1 and R2 with R1 > R2. If the two are at the same potential, the larger sphere has more charge than the smaller sphere. State whether the charge density of the smaller sphere is more or less than that of the larger one.
Answer:
Equal potentials: \( \dfrac{kq_1}{R_1} = \dfrac{kq_2}{R_2} \).
Put \( q = \sigma\,4\pi R^2 \): \( \dfrac{k\sigma_1 4\pi R_1^2}{R_1} = \dfrac{k\sigma_2 4\pi R_2^2}{R_2} \Rightarrow \sigma_1R_1 = \sigma_2R_2 \Rightarrow \dfrac{\sigma_2}{\sigma_1} = \dfrac{R_1}{R_2} \).
Since R1 > R2, σ2 > σ1. The smaller sphere has the larger (more) surface charge density.
In simple words: At the same potential the surface charge density is inversely proportional to the radius, so the smaller sphere carries more charge per unit area.

Teacher's Note:
1. This is why charge collects at sharp points of a conductor: a sharp point has a very small radius of curvature.
2. The larger sphere has more total charge but spread over a much bigger area.

Examination Note: Replace q by σ·4πR² in V = kq/R to get σR = constant; the result is then immediate.

 

Question 15. Do free electrons travel to region of higher potential or lower potential?
Answer:
Free electrons are negatively charged, so the force on them is opposite to the electric field.
The electric field points from higher to lower potential, so electrons are pushed from lower to higher potential.
Free electrons travel towards the region of higher potential.
In simple words: Electrons are pulled towards positive (higher potential) regions.

Teacher's Note:
1. A positive charge moves to lower potential energy by going to lower potential; for a negative charge the reverse holds.
2. The same reasoning explains the direction of conventional current compared with the electron flow.

Examination Note: Give the reason in two steps: the force is opposite to E, and E points to lower potential.

 

Question 16. Can there be a potential difference between two adjacent conductors carrying the same charge?
Answer:
Yes. The potential of an isolated conductor is \( V = \dfrac{Q}{C} \), where C depends on the size, shape and surroundings of the conductor.
If the two conductors have different capacitances (different sizes or shapes), then for the same Q their potentials Q/C are different, so there is a potential difference between them.
In simple words: Equal charges do not mean equal potentials, because a conductor with a smaller capacitance reaches a higher potential for the same charge.

Teacher's Note:
1. Potential depends on charge and capacitance together: V = Q/C.
2. Two equal spheres with equal charge would have no potential difference; unequal spheres would.

Examination Note: Write V = Q/C and say that C differs for conductors of different geometry.

 

Question 17. Can the potential function have a maximum or minimum in free space?
Answer:
No. Suppose V had a maximum at a point P in a region free of charge. The potential would decrease in every direction away from P, so the field \( \vec E = -\nabla V \) would point away from P on all sides.
Then there would be a net outward flux through a small closed surface around P, although no charge is enclosed. This contradicts Gauss' law. A minimum gives an inward flux, which is equally impossible.
Hence in charge-free space the potential has no maximum or minimum. (It can be extreme only at a point where a charge is present.)
In simple words: In empty space V cannot have a peak or a dip, because that would need a field pointing all outwards or all inwards without any charge there.

Teacher's Note:
1. The same result follows from Laplace's equation ∇²V = 0, which holds in charge-free space.
2. This is why a charge cannot be held in stable equilibrium by electrostatic forces alone.

Examination Note: Use Gauss' law to show the contradiction; this is the shortest valid argument.

 

Question 18. A test charge q is made to move in the electric field of a point charge Q along two different closed paths (figure). The first path has sections along and perpendicular to lines of electric field. The second path is a rectangular loop of the same area as the first loop. How does the work done compare in the two cases?
baOθ
Answer:
The electrostatic field of a point charge is conservative: the work done depends only on the end points, not on the path.
Both paths are closed loops, so the starting point and the end point coincide. Therefore the work done is zero in both cases, i.e. \( \oint \vec E\cdot d\vec l = 0 \).
For the first path this can also be seen directly: on the arcs perpendicular to the field no work is done, and the work on the two radial sections is equal and opposite.
In simple words: The work done around any closed path in an electrostatic field is zero, so the two loops require the same work, namely none.

Teacher's Note:
1. Gravity is also conservative; a round trip returns all the energy.
2. A closed path with non-zero work would allow a machine to gain energy from the field for free.

Examination Note: State that the field is conservative and that a closed path has the same start and end point.

 

Short Answer Type Questions

Question 19. Prove that a closed equipotential surface with no charge within itself must enclose an equipotential volume.
Answer:
Suppose the surface is at potential V0 and there is no charge inside it. Assume that the potential inside is not the same everywhere. Then the field \( \vec E = -\dfrac{dV}{dr} \) is not zero somewhere inside, and a field line passes through that point.
A field line must begin and end on charges (or go to infinity). There is no charge inside the surface, so the line must begin and end on the surface itself.
But the potential decreases steadily along a field line, so the two ends of the line cannot be at the same potential. Both ends lie on the equipotential surface, which is a contradiction.
Hence there is no field inside, so the potential has the constant value V0 throughout the enclosed volume: it is an equipotential volume.
In simple words: If there were a field inside, its lines would have to start and end on the surface, but a surface of one potential cannot hold both ends of a line.

Teacher's Note:
1. Field lines always go from higher to lower potential.
2. A conducting shell is a practical example: the whole space inside it is at the potential of the shell.

Examination Note: Write the proof as a contradiction in three short steps: assumption, field lines need charges, potential must fall along a line.

 

Question 20. A capacitor has some dielectric between its plates and the capacitor is connected to a DC source. The battery is now disconnected and then the dielectric is removed. State whether the capacitance, the energy stored in it, electric field, charge stored and the voltage will increase, decrease or remain constant.
Answer:
The capacitance is \( C = \dfrac{K\varepsilon_0A}{d} \). Removing the dielectric makes K = 1, so C decreases.
The battery is disconnected, so the plates are isolated and the charge Q remains constant.
Voltage \( V = \dfrac{Q}{C} \): Q is constant and C decreases, so V increases.
Electric field \( E = \dfrac{V}{d} \), with d unchanged, so E increases.
Energy \( U = \dfrac{Q^2}{2C} \): Q is constant and C decreases, so the stored energy increases (the work done in pulling out the dielectric is stored).
In simple words: After disconnecting the battery the charge is fixed; removing the dielectric lowers C, and so V, E and the energy all rise.

Teacher's Note:
1. With the battery connected, V would stay constant and Q would fall instead.
2. The dielectric is pulled into the capacitor by the field; removing it needs work from you, which explains the gain in energy.

Examination Note: List the five quantities in order (C, Q, V, E, U) with one line of reasoning each; this layout is expected by examiners.

 

Question 21. Prove that, if an insulated, uncharged conductor is placed near a charged conductor and no other conductors are present, the uncharged body must be intermediate in potential between that of the charged body and that of infinity.
Answer:
Let the charged conductor be positive. Its field lines start on it and end either on the uncharged conductor (on its induced negative charge) or at infinity.
Take a field line from the charged body to the uncharged body. The potential falls along this line, so \( V_{\text{charged}} > V_{\text{uncharged}} \).
The uncharged body has an equal positive induced charge on its far side. Field lines from it go on to infinity, along which the potential falls again, so \( V_{\text{uncharged}} > V_{\infty} = 0 \).
Hence \( V_{\text{charged}} > V_{\text{uncharged}} > V_{\infty} \): the uncharged body is at a potential between that of the charged body and infinity. For a negatively charged body the same argument holds with all inequalities reversed.
In simple words: Potential falls along field lines, and the lines run from the charged body to the neutral one and then on to infinity.

Teacher's Note:
1. A neutral conductor has induced charges of both signs, so lines both end and start on it.
2. The same idea is used in explaining why a neutral object is attracted by a charged rod.

Examination Note: Draw the chain charged body, neutral body and infinity along a field line and state the order of the potentials.

 

Question 22. Calculate potential energy of a point charge −q placed along the axis due to a charge +Q uniformly distributed along a ring of radius R. Sketch PE as a function of axial distance z from the centre of the ring. Looking at graph, can you see what would happen if −q is displaced slightly from the centre of the ring (along the axis)?
Answer:
Every element dQ of the ring is at the same distance \( \sqrt{z^2+R^2} \) from a point P on the axis at distance z from the centre. So the potential at P is \( V = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q}{\sqrt{z^2+R^2}} \).
Potential energy of the charge −q at P: \( U = (-q)V = -\dfrac{1}{4\pi\varepsilon_0}\dfrac{Qq}{\sqrt{z^2+R^2}} \).
Graph: U is negative everywhere, has its lowest value \( -\dfrac{Qq}{4\pi\varepsilon_0R} \) at z = 0, and rises symmetrically towards zero as |z| becomes large (figure below).
Inference: z = 0 is a minimum of U, so it is a position of stable equilibrium for the charge −q on the axis. If −q is displaced slightly along the axis, it is pulled back towards the centre and oscillates about it. For small z, \( U \approx -\dfrac{kQq}{R} + \dfrac{kQq}{2R^3}z^2 \), which has the form of a simple harmonic oscillator.
zUU = −kQq/RO
In simple words: The potential energy is lowest at the centre, so a slightly displaced −q returns and oscillates about the centre.

Teacher's Note:
1. A minimum of U means stable equilibrium, a maximum means unstable equilibrium.
2. The graph for +q would be turned upside down, with a maximum at the centre.

Examination Note: Give the expression for U, the sketch with the minimum clearly marked at z = 0, and one sentence about stable oscillation.

 

Question 23. Calculate potential on the axis of a ring due to charge Q uniformly distributed along the ring of radius R.
Answer:
Let P be a point on the axis at distance x from the centre. A small element of the ring carrying charge dq is at distance \( r = \sqrt{x^2+R^2} \) from P, the same for all elements.
\( V = \dfrac{1}{4\pi\varepsilon_0}\int\dfrac{dq}{r} = \dfrac{1}{4\pi\varepsilon_0}\dfrac{1}{\sqrt{x^2+R^2}}\int dq \)
\( V = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q}{\sqrt{x^2+R^2}} \)
At the centre (x = 0), \( V = \dfrac{Q}{4\pi\varepsilon_0R} \); for x >> R, \( V \approx \dfrac{Q}{4\pi\varepsilon_0 x} \), the potential of a point charge.
In simple words: Every bit of the ring is the same distance from the axis point, so the potentials just add up to a total charge Q divided by that distance.

Teacher's Note:
1. Potential is a scalar, so no components or directions are needed; this is why it is easier to find than the field.
2. Checking the limit x >> R gives the point-charge result.

Examination Note: Mention that all elements are equidistant, then integrate dq to get Q; add the two limiting cases as a check.

 

Long Answer Type Questions

Question 24. Find the equation of the equipotentials for an infinite cylinder of radius r0 carrying charge of linear density λ.
Answer:
By symmetry the field is radial. Take a coaxial Gaussian cylinder of radius r and length l: \( E\,(2\pi r l) = \dfrac{\lambda l}{\varepsilon_0} \Rightarrow E = \dfrac{\lambda}{2\pi\varepsilon_0 r} \).
Potential difference between radius r and radius r0: \( V(r) - V(r_0) = -\int_{r_0}^{r}E\,dr = -\dfrac{\lambda}{2\pi\varepsilon_0}\ln\dfrac{r}{r_0} \).
Solving for r: \( \ln\dfrac{r}{r_0} = -\dfrac{2\pi\varepsilon_0}{\lambda}\,[V(r)-V(r_0)] \), so
\( r = r_0\,e^{-2\pi\varepsilon_0\,[V(r)-V(r_0)]/\lambda} \)
For each value of V the radius r is fixed, so the equipotential surfaces are co-axial cylinders around the charged cylinder.
In simple words: The potential depends only on the distance from the axis, so surfaces of equal potential are cylinders with the same axis; larger V (for λ > 0) corresponds to smaller r.

Teacher's Note:
1. The field of a line charge falls as 1/r, so the potential changes as ln r.
2. Unlike a point charge, the potential of an infinite line cannot be set to zero at infinity; hence a reference radius r0 is used.

Examination Note: Obtain E from Gauss' law, integrate to V(r) − V(r0) and then solve for r; state clearly that the surfaces are co-axial cylinders.

 

Question 25. Two point charges of magnitude +q and −q are placed at (−d/2, 0, 0) and (d/2, 0, 0), respectively. Find the equation of the equipotential surface where the potential is zero.
Answer:
Let P be a point of the required surface at a distance x from the origin along the x-axis and h perpendicular to it (general point (x, y, z), \( h^2 = y^2+z^2 \)).
Potential at P: \( V = \dfrac{1}{4\pi\varepsilon_0}\left[\dfrac{q}{\sqrt{(x+d/2)^2+h^2}} - \dfrac{q}{\sqrt{(x-d/2)^2+h^2}}\right] \).
For V = 0 the two distances must be equal: \( (x+d/2)^2 + h^2 = (x-d/2)^2 + h^2 \Rightarrow 2xd = 0 \Rightarrow x = 0 \).
The zero-potential surface is the plane x = 0, i.e. the y-z plane, which is the perpendicular bisector plane of the line joining the two charges.
+q−q(−d/2, 0, 0)(d/2, 0, 0)OPhx
In simple words: Every point of the plane midway between the two charges is equally far from both, so the potentials of +q and −q cancel exactly.

Teacher's Note:
1. Potentials add as numbers (scalars); the field on this plane is not zero, only the potential is.
2. The same plane is the equipotential at V = 0 for any dipole.

Examination Note: Equate the two distances; it removes the square roots at once and gives x = 0 in one line.

 

Question 26. A parallel plate capacitor is filled by a dielectric whose relative permittivity varies with the applied voltage (U) as ε = αU where α = 2 V−1. A similar capacitor with no dielectric is charged to U0 = 78 V. It is then connected to the uncharged capacitor with the dielectric. Find the final voltage on the capacitors.
Answer:
Let C be the capacitance of the capacitor without dielectric and U the final common voltage. The capacitor with the dielectric has capacitance εC = αUC.
Initial charge: Q0 = CU0. Final charges: Q1 = CU on the air capacitor, Q2 = (αUC)U = αCU² on the dielectric capacitor.
Conservation of charge: \( CU_0 = CU + \alpha CU^2 \Rightarrow \alpha U^2 + U - U_0 = 0 \).
\( U = \dfrac{-1+\sqrt{1+4\alpha U_0}}{2\alpha} = \dfrac{-1+\sqrt{1+4\times2\times78}}{4} = \dfrac{-1+25}{4} = \) 6 V
In simple words: The dielectric's capacitance itself depends on the voltage, so charge conservation gives a quadratic in U; the positive root is the answer.

Teacher's Note:
1. Both capacitors end at the same voltage because they are connected in parallel.
2. Reject the negative root, since the voltage across the capacitors cannot be negative here.

Examination Note: Write the equation αU² + U − U0 = 0 clearly and notice that 625 = 25² makes the root exact.

 

Question 27. A capacitor is made of two circular plates of radius R each, separated by a distance d << R. The capacitor is connected to a constant voltage. A thin conducting disc of radius r << R and thickness t << r is placed at the centre of the bottom plate. Find the minimum voltage required to lift the disc if the mass of the disc is m.
Answer:
The disc lies on the bottom plate, so it is at the potential of that plate. The field between the plates is \( E = \dfrac{V}{d} \), and the disc's upper face carries surface charge density \( \sigma = \varepsilon_0E \).
Charge on the disc: \( q' = \sigma\pi r^2 = \dfrac{\varepsilon_0V\pi r^2}{d} \).
The charge on the surface of a conductor feels the average of the field outside (E) and inside (0), which is E/2. So the upward force is \( F = q'\cdot\dfrac{E}{2} = \dfrac{\varepsilon_0\pi r^2V^2}{2d^2} \).
The disc just lifts when \( F = mg \): \( \dfrac{\varepsilon_0\pi r^2V^2}{2d^2} = mg \Rightarrow \) \( V = d\sqrt{\dfrac{2mg}{\pi\varepsilon_0r^2}} \).
In simple words: The disc is lifted when the electric force on the charge of its upper face balances its weight; the force on a conductor's surface charge uses half of the outside field.

Teacher's Note:
1. The force per unit area on a charged conductor surface is \( \dfrac{\sigma^2}{2\varepsilon_0} = \dfrac{\varepsilon_0E^2}{2} \).
2. Taking the full field E on the charge instead of E/2 gives \( d\sqrt{mg/(\pi\varepsilon_0r^2)} \), which is too small by a factor of √2.

Examination Note: Show where the factor 1/2 comes from (electrostatic pressure σ²/2ε0), and give the final result in terms of m, g, d and r only.

 

Question 28. (a) In a quark model of elementary particles, a neutron is made of one up quark [charge (2/3)e] and two down quarks [charges −(1/3)e]. Assume that they have a triangle configuration with side length of the order of 10−15 m. Calculate electrostatic potential energy of neutron and compare it with its mass 939 MeV. (b) Repeat above exercise for a proton which is made of two up and one down quark.
Answer:
The potential energy of the system is the sum over the three pairs, each at distance r = 10−15 m. Note \( \dfrac{e^2}{4\pi\varepsilon_0r} = \dfrac{9\times10^{9}\times(1.6\times10^{-19})^2}{10^{-15}} = 2.304\times10^{-13}\ \text{J} \).
(a) Neutron (u, d, d): \( U = \dfrac{e^2}{4\pi\varepsilon_0r}\left[\left(-\tfrac13\right)\left(-\tfrac13\right) + 2\left(\tfrac23\right)\left(-\tfrac13\right)\right] = 2.304\times10^{-13}\left(\tfrac19-\tfrac49\right) = -7.68\times10^{-14}\ \text{J} \).
In eV: \( U = \dfrac{-7.68\times10^{-14}}{1.6\times10^{-19}} = -4.8\times10^{5}\ \text{eV} = \) −0.48 MeV. Compared with the rest energy 939 MeV: \( \dfrac{0.48}{939} \approx 5.1\times10^{-4} \), about 0.05 %, which is negligible.
(b) Proton (u, u, d): \( U = \dfrac{e^2}{4\pi\varepsilon_0r}\left[\left(\tfrac23\right)\left(\tfrac23\right) + 2\left(\tfrac23\right)\left(-\tfrac13\right)\right] = 2.304\times10^{-13}\left(\tfrac49-\tfrac49\right) = \) 0. The electrostatic energy of the proton (rest energy about 938 MeV) is zero in this model.
In simple words: Add the pair energies of the three quarks; the result is small compared with the rest energy, and for the proton the repulsion and attraction cancel exactly.

Teacher's Note:
1. Potential energy of a system of charges is the sum over every pair, counted once.
2. The binding of quarks is due mainly to the strong force, not to the electrostatic force.

Examination Note: Set out the three pair terms with their charge products before substituting numbers; this makes the cancellation in (b) obvious.

 

Question 29. Two metal spheres, one of radius R and the other of radius 2R, both have same surface charge density σ. They are brought in contact and separated. What will be new surface charge densities on them?
Answer:
Charges before contact: \( Q_1 = \sigma\,4\pi R^2 \) and \( Q_2 = \sigma\,4\pi(2R)^2 = 4Q_1 \). Total charge = 5Q1 = \( 5\sigma\,4\pi R^2 \).
In contact the spheres reach the same potential: \( \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q_1'}{R} = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q_2'}{2R} \Rightarrow Q_2' = 2Q_1' \).
With \( Q_1' + Q_2' = 5\sigma\,4\pi R^2 \): \( Q_1' = \dfrac53\,(\sigma\,4\pi R^2) \) and \( Q_2' = \dfrac{10}{3}\,(\sigma\,4\pi R^2) \).
New densities: \( \sigma_1' = \dfrac{Q_1'}{4\pi R^2} = \) \( \dfrac{5}{3}\sigma \) and \( \sigma_2' = \dfrac{Q_2'}{4\pi(2R)^2} = \) \( \dfrac{5}{6}\sigma \).
In simple words: Charge is shared in proportion to the radii so that the potentials are equal; the smaller sphere ends up with the larger charge density.

Teacher's Note:
1. Check: σ1′R = σ2′(2R) gives σ1′ = 2σ2′, and 5/3 = 2 × 5/6.
2. Total charge before and after is the same (conservation of charge).

Examination Note: Use two equations: equal potential and conservation of charge; then convert charges to densities with the correct area for each sphere.

 

Question 30. In the circuit shown in figure, initially K1 is closed and K2 is open. What are the charges on each capacitor? Then K1 was opened and K2 was closed (order is important), what will be the charge on each capacitor now? [C = 1 µF]
C=23CE =9VK2K1C=33CC=16C
Answer:
Stage 1 (K1 closed, K2 open). The battery, C1 = 6C and C2 = 3C are in series; C3 is cut off, so Q3 = 0.
Equivalent capacitance: \( C_{eq} = \dfrac{6C\times3C}{6C+3C} = 2C = 2\ \mu\text{F} \). In a series combination every capacitor has the same charge: \( Q = C_{eq}E = 2\times9 = 18\ \mu\text{C} \).
So Q1 = 18 µC, Q2 = 18 µC and Q3 = 0. (Voltages: V1 = 18/6 = 3 V and V2 = 18/3 = 6 V, which add up to 9 V.)
Stage 2 (K1 opened, K2 closed). C1 is now isolated and keeps its charge, Q1 = 18 µC.
C2 (charge 18 µC) is now connected in parallel with the uncharged C3. The 18 µC is shared until the voltages are equal: \( V = \dfrac{18}{3+3} = 3\ \text{V} \).
Q2 = 3 × 3 = 9 µC and Q3 = 3 × 3 = 9 µC.
Final charges: C1 = 18 µC, C2 = 9 µC, C3 = 9 µC.
In simple words: In series the charge is the same on every capacitor; after the key change the charge of C2 is shared equally with the equal capacitor C3, while C1 is left holding its charge.

Teacher's Note:
1. Capacitors in series carry equal charge (not equal voltage).
2. Check stage 2: total charge on the connected plates is 9 + 9 = 18 µC, the same as before.

Examination Note: Draw the two stages separately and state for each which rule is used: series gives equal charge; parallel gives equal voltage and conserved charge.

 

Question 31. Calculate potential on the axis of a disc of radius R due to a charge Q uniformly distributed on its surface.
Answer:
Surface charge density: \( \sigma = \dfrac{Q}{\pi R^2} \). Divide the disc into thin rings; take a ring of radius r and width dr, carrying charge \( dq = \sigma\,2\pi r\,dr \).
The potential at a point P on the axis, at distance x from the centre, due to this ring: \( dV = \dfrac{1}{4\pi\varepsilon_0}\dfrac{\sigma\,2\pi r\,dr}{\sqrt{r^2+x^2}} \) (using the result for a ring).
\( V = \dfrac{\sigma}{2\varepsilon_0}\int_0^R\dfrac{r\,dr}{\sqrt{r^2+x^2}} = \dfrac{\sigma}{2\varepsilon_0}\Big[\sqrt{r^2+x^2}\Big]_0^R = \dfrac{\sigma}{2\varepsilon_0}\left[\sqrt{R^2+x^2}-x\right] \)
Substituting \( \sigma = \dfrac{Q}{\pi R^2} \): \( V = \dfrac{Q}{2\pi\varepsilon_0R^2}\left[\sqrt{R^2+x^2}-x\right] \).
For x >> R, \( \sqrt{R^2+x^2}-x \approx \dfrac{R^2}{2x} \), so \( V \approx \dfrac{Q}{4\pi\varepsilon_0x} \), the potential of a point charge.
In simple words: A disc is a set of rings; add up the potentials of all rings from the centre to the edge.

Teacher's Note:
1. The integral of r/√(r²+x²) is √(r²+x²), which is the key step.
2. The limit x >> R gives a useful check of the final formula.

Examination Note: State the ring element dq = σ·2πr dr, integrate from 0 to R and finish with the large-distance check.

 

Question 32. Two charges q1 and q2 are placed at (0, 0, d) and (0, 0, −d) respectively. Find locus of points where the potential is zero.
Answer:
Let P(x, y, z) be a point of zero potential: \( \dfrac{q_1}{\sqrt{x^2+y^2+(z-d)^2}} + \dfrac{q_2}{\sqrt{x^2+y^2+(z+d)^2}} = 0 \). This needs q1 and q2 of opposite sign.
Square: \( q_1^2\left[x^2+y^2+(z+d)^2\right] = q_2^2\left[x^2+y^2+(z-d)^2\right] \).
Collect the terms: \( (q_2^2-q_1^2)(x^2+y^2+z^2+d^2) = 2dz\,(q_1^2+q_2^2) \), that is \( x^2+y^2+z^2+\dfrac{q_1^2+q_2^2}{q_1^2-q_2^2}\,(2zd)+d^2 = 0 \).
This is the equation of a sphere. Comparing with \( x^2+y^2+(z-c)^2 = \rho^2 \): centre \( \left(0,\,0,\,-d\,\dfrac{q_1^2+q_2^2}{q_1^2-q_2^2}\right) \) and radius \( \rho = \dfrac{2d\,|q_1q_2|}{|q_1^2-q_2^2|} \).
(If |q1| = |q2|, the locus is the plane z = 0.)
In simple words: The zero-potential points of two unequal opposite charges form a sphere, which does not enclose the charge of larger magnitude.

Teacher's Note:
1. Equal and opposite charges give a plane (the bisector), the limiting case of an infinitely large sphere.
2. The sphere surrounds the charge of smaller magnitude.

Examination Note: Square the equation carefully, collect terms and complete the square; give the centre and the radius for full marks.

 

Question 33. Two charges −q each are separated by distance 2d. A third charge +q is kept at mid-point O. Find potential energy of +q as a function of small distance x from O due to −q charges. Sketch PE vs x and convince yourself that the charge at O is in an unstable equilibrium.
Answer:
Displace +q by x along the line joining the charges, towards one of them. The distances from the two −q charges are (d − x) and (d + x).
\( U = \dfrac{1}{4\pi\varepsilon_0}\left[\dfrac{-q^2}{d-x}+\dfrac{-q^2}{d+x}\right] = -\dfrac{q^2}{4\pi\varepsilon_0}\cdot\dfrac{2d}{d^2-x^2} \)
Equilibrium: \( F = -\dfrac{dU}{dx} \propto \dfrac{x}{(d^2-x^2)^2} = 0 \Rightarrow x = 0 \).
Second derivative at x = 0: \( \dfrac{d^2U}{dx^2}\Big|_{x=0} = -\dfrac{q^2}{4\pi\varepsilon_0}\cdot\dfrac{4}{d^3} = -\dfrac{q^2}{\pi\varepsilon_0d^3} \), which is negative.
A negative second derivative means U is a maximum at x = 0 (figure). For any small displacement U decreases, so the charge is pushed further away: the equilibrium at O is unstable.
xUx = dx = −dOmaximum at x = 0
In simple words: At the mid-point the potential energy is a maximum along the line joining the charges, so a small displacement makes the charge accelerate away.

Teacher's Note:
1. Stable equilibrium needs a minimum of U (d²U/dx² > 0); here the sign is the opposite.
2. Along the perpendicular bisector the same charge would be in stable equilibrium, so O is stable in one direction and unstable in another.

Examination Note: State the test used (sign of the second derivative of U) and draw the graph with the peak at x = 0.