NCERT Exemplar Solutions Class 12 Physics Chapter 14 Semiconductor Electronics

These NCERT Exemplar solutions for Class 12 Physics Chapter 14, Semiconductor Electronics: Materials, Devices and Simple Circuits, give step-by-step answers to all 40 questions: 8 MCQs, 8 multiple-correct MCQs, 6 very short, 8 short and 10 long answer questions. They cover energy bands, p-n junction, diodes as rectifiers and clippers, Zener regulation, transistor as switch and amplifier, and logic gates. Each answer is followed by a short Teacher's Note to build understanding and an Examination Note on how to present the answer for better marks.

Multiple Choice Questions (MCQs)

Question 1: The conductivity of a semiconductor increases with increase in temperature, because
(a) number density of free current carriers increases
(b) relaxation time increases
(c) both number density of carriers and relaxation time increase
(d) number density of carriers increases, relaxation time decreases but effect of decrease in relaxation time is much less than increase in number density
Show Answer & Explanation

Answer: (d) number density of carriers increases, relaxation time decreases but effect of decrease in relaxation time is much less than increase in number density

Explanation:
1. Conductivity is \( \sigma = ne^2\tau/m \) (for electrons; holes add a similar term), so it depends on the number density n of carriers and the relaxation time τ.
2. On heating, more electrons break free from covalent bonds, so n rises very rapidly (exponentially). The lattice vibrates more, so collisions are more frequent and τ decreases, but only slightly.
3. The large rise in n outweighs the small fall in τ, so the conductivity increases: (d).

Teacher's Note:
1. In a metal n is fixed and τ falls with temperature, so conductivity falls. In a semiconductor n changes enormously, so conductivity rises.
2. Option (b) and (c) are wrong because τ never increases with temperature.

Examination Note: Write the formula σ = ne²τ/m and compare the size of the two changes; do not just state that n increases.

 

Question 2: In the figure given below, V0 is the potential barrier across a p-n junction, when no battery is connected across the junction.
123V0Potential barrier V₀ (curves 1, 2, 3) (a) 1 and 3 both correspond to forward bias of junction
(b) 3 corresponds to forward bias of junction and 1 corresponds to reverse bias of junction
(c) 1 corresponds to forward bias and 3 corresponds to reverse bias
(d) 3 and 1 both correspond to reverse bias of junction
Show Answer & Explanation

Answer: (b) 3 corresponds to forward bias of junction and 1 corresponds to reverse bias of junction

Explanation:
1. Curve 2 is the unbiased junction. Forward bias applies a voltage that opposes the built-in potential, so the barrier becomes lower than V0: this is curve 3.
2. Reverse bias applies a voltage in the same sense as the built-in potential, so the barrier becomes higher than V0: this is curve 1. Hence (b).

Teacher's Note:
1. Forward bias lowers the barrier and narrows the depletion region; reverse bias raises the barrier and widens it.
2. Current flows easily only when the barrier is lowered.

Examination Note: State what happens to the barrier height for each bias, then match with the curves.

 

Question 3: In the figure given below, assuming the diodes to be ideal,
−10 VABRD1D2 (a) D1 is forward biased and D2 is reverse biased and hence current flows from A to B
(b) D2 is forward biased and D1 is reverse biased and hence no current flows from B to A and vice-versa
(c) D1 and D2 are both forward biased and hence current flows from A to B
(d) D1 and D2 are both reverse biased and hence no current flows from A to B and vice-versa
Show Answer & Explanation

Answer: (b) D2 is forward biased and D1 is reverse biased and hence no current flows from B to A and vice-versa

Explanation:
1. The p-side (anode) of D1 is connected to A, which is at −10 V, and its n-side is joined to the n-side of D2. The p-side of D2 is at B, which is at 0 V (earth).
2. D1: its anode is at −10 V and its cathode is at a higher potential, so D1 is reverse biased. D2: its anode is at 0 V and its cathode is at a lower potential, so D2 is forward biased.
3. The two diodes are in series with opposite orientations (cathode to cathode). The reverse-biased D1 blocks the current, so no current flows between A and B in either direction: (b).

Teacher's Note:
1. Diodes in series back to back always block: one of them is reverse biased.
2. Option (b) itself says no current flows, and an ideal reverse-biased diode blocks completely.

Examination Note: Mark the polarity of each diode with respect to the potentials of A and B, then say that the series combination blocks.

 

Question 4: A 220 V AC supply is connected between points A and B (figure). What will be the potential difference V across the capacitor?
AB220 V ACCV (a) 220 V
(b) 110 V
(c) 0 V
(d) \( 220\sqrt{2} \) V
Show Answer & Explanation

Answer: (d) \( 220\sqrt{2} \) V

Explanation:
1. The diode conducts only in the positive half cycle (when A is positive), and the capacitor charges through it.
2. The capacitor charges up to the peak value of the supply, \( V_0 = \sqrt{2}\,V_{rms} = 220\sqrt{2} \approx 311 \) V.
3. When the supply voltage falls, the diode becomes reverse biased and the capacitor has no path to discharge (no load), so it stays at the peak value: (d).

Teacher's Note:
1. The rated 220 V of an AC supply is the rms value; the peak is √2 times larger.
2. In the original figure the label reads 200 AC; it is a misprint for 220 V AC.

Examination Note: Convert rms to peak and say why the capacitor keeps this value (no discharge path).

 

Question 5: Hole is
(a) an anti-particle of electron
(b) a vacancy created when an electron leaves a covalent bond
(c) absence of free electrons
(d) an artificially created particle
Show Answer & Explanation

Answer: (b) a vacancy created when an electron leaves a covalent bond

Explanation:
1. When an electron leaves a covalent bond, it leaves an empty place with a net positive charge. This vacancy is called a hole.
2. A neighbouring bond electron can jump into it, so the hole appears to move in the opposite direction: (b).

Teacher's Note:
1. A hole is not a real particle; it is only a convenient way to describe the missing electron.
2. An anti-particle of the electron is the positron.

Examination Note: Define a hole as a vacancy left in a covalent bond and mention that it carries a positive charge.

 

Question 6: The output of the given circuit in the figure given below,
vm sin ωt (a) would be zero at all times
(b) would be like a half wave rectifier with positive cycles in output
(c) would be like a half wave rectifier with negative cycles in output
(d) would be like that of a full wave rectifier
Show Answer & Explanation

Answer: (c) would be like a half wave rectifier with negative cycles in output

Explanation:
1. The output is taken across the diode, which is in parallel with the output terminals. The resistor is in series with the source.
2. In the positive half cycle the diode is forward biased and has a very small resistance, so almost the whole voltage drops across the resistor and the output across the diode is nearly zero.
3. In the negative half cycle the diode is reverse biased and its resistance is very large compared with the resistor, so almost the whole input voltage appears across the diode. The output contains only the negative half cycles: (c).

Teacher's Note:
1. Voltage divides in proportion to resistance: the larger resistance takes the larger voltage.
2. A single diode can never give a full wave output.

Examination Note: Explain the two half cycles separately using the voltage divider idea.

 

Question 7: In the circuit shown in the figure given below, if the diode forward voltage drop is 0.3 V, the voltage difference between A and B is
A0.2 mAr15 kΩC0.3 Vr25 kΩB (a) 1.3 V
(b) 2.3 V
(c) 0
(d) 0.5 V
Show Answer & Explanation

Answer: (b) 2.3 V

Explanation:
1. For a steady DC current the capacitor blocks the branch, so the 0.2 mA flows through the two 5 kΩ resistors and the diode in series.
2. Voltage across the resistors: \( 0.2\times10^{-3}\times(5+5)\times10^{3} = 2 \) V.
3. Adding the diode drop: \( V_A - V_B = 2 + 0.3 = 2.3 \) V: (b).

Teacher's Note:
1. A capacitor is an open circuit for DC.
2. A diode with a forward drop acts like a small battery of that emf in series with the current path.

Examination Note: Show V = IR + 0.3 with the numbers substituted.

 

Question 8: The truth table for the given circuit is
ABCDE (a) A B E: 00→1, 01→0, 10→1, 11→0
(b) A B E: 00→1, 01→0, 10→0, 11→1
(c) A B E: 00→0, 01→1, 10→0, 11→1
(d) A B E: 00→0, 01→1, 10→1, 11→0
Show Answer & Explanation

Answer: (c) A B E: 00→0, 01→1, 10→0, 11→1

Explanation:
1. The upper AND gate gives \( C = A\cdot B \). The NOT gate gives \( \bar A \), and the lower AND gate gives \( D = \bar A\cdot B \).
2. The OR gate gives \( E = C + D = AB + \bar A B = B(A + \bar A) = B \).
3. So E simply copies B: 0 for B = 0 and 1 for B = 1, whatever A is. This is the table in (c): 00→0, 01→1, 10→0, 11→1.

Teacher's Note:
1. Boolean identity A + Ā = 1 reduces the expression.
2. Check with a full table: for A B = 01, C = 0 and D = 1, so E = 1; for A B = 11, C = 1 and D = 0, so E = 1.

Examination Note: Write C and D, simplify E using A + Ā = 1, and then pick the matching table.

 

Multiple Choice Questions (More Than One Option)

Question 9: When an electric field is applied across a semiconductor
(a) electrons move from lower energy level to higher energy level in the conduction band
(b) electrons move from higher energy level to lower energy level in the conduction band
(c) holes in the valence band move from higher energy level to lower energy level
(d) holes in the valence band move from lower energy level to higher energy level
Show Answer & Explanation

Answer: (a) electrons move from lower energy level to higher energy level in the conduction band, (c) holes in the valence band move from higher energy level to lower energy level

Explanation:
1. The field accelerates electrons in the conduction band, so they gain energy and move to higher levels within the band: (a).
2. Holes are missing electrons. A hole rises in the hole-energy picture when an electron fills it from below, so in the valence band the hole moves to lower electron-energy levels, i.e. from higher to lower energy level (c) in the usual band diagram.

Teacher's Note:
1. The energy scale for holes is opposite to that of electrons: holes lower in the band diagram have more energy.
2. Electrons gain kinetic energy from the field; holes drift in the direction of the field.

Examination Note: Say that electrons go up in the conduction band while holes go down in the valence band diagram.

 

Question 10: Consider an n-p-n transistor with its base-emitter junction forward biased and collector base junction reverse biased. Which of the following statements are true?
npnEmitter junctionCollector junctionEBCForward biasedReverse biased (a) Electrons cross over from emitter to collector
(b) Holes move from base to collector
(c) Electrons move from emitter to base
(d) Electrons from emitter move out of base without going to the collector
Show Answer & Explanation

Answer: (a) Electrons cross over from emitter to collector, (c) Electrons move from emitter to base

Explanation:
1. With the emitter-base junction forward biased, the many electrons of the n-type emitter are injected into the thin p-type base: (c).
2. The base is very thin and lightly doped, so most of these electrons are swept across the reverse-biased base-collector junction into the collector: (a).
3. Holes do not move from the base to the collector (b), and only a small fraction of the electrons recombine in the base or leave through the base terminal; the majority reach the collector, so (d) is not a general statement.

Teacher's Note:
1. Transistor action depends on a thin base: about 95 to 99 per cent of the emitter electrons reach the collector.
2. The base current is only the small recombination current.

Examination Note: Describe the motion of the electrons in sequence: emitter, thin base, collector.

 

Question 11: The figure given below shows the transfer characteristics of a base biased CE transistor. Which of the following statements are true?
VoVi00.6 V2 V (a) At Vi = 0.4 V, transistor is in active state
(b) At Vi = 1 V, it can be used as an amplifier
(c) At Vi = 0.5 V, it can be used as a switch turned off
(d) At Vi = 2.5 V, it can be used as a switch turned on
Show Answer & Explanation

Answer: (b) At Vi = 1 V, it can be used as an amplifier, (c) At Vi = 0.5 V, it can be used as a switch turned off, (d) At Vi = 2.5 V, it can be used as a switch turned on

Explanation:
1. For Vi below about 0.6 V the output stays at its maximum value because no collector current flows: the transistor is in the cut-off region. At 0.4 V and 0.5 V it is cut off, so (a) is false and (c) is true (switch turned off).
2. Between about 0.6 V and 2 V the output falls steadily with the input: this sloping part is the active region. At 1 V the transistor can be used as an amplifier: (b).
3. Above about 2 V the output is nearly zero and the collector current is at its maximum: the transistor is saturated and acts as a closed switch (switch turned on): (d).

Teacher's Note:
1. Cut-off: switch off. Active: amplifier. Saturation: switch on.
2. 0.4 V is not an active state; the output is at its highest value there, which means no collector current.

Examination Note: Name the three regions of the transfer curve and match each given Vi to one of them.

 

Question 12: In an n-p-n transistor circuit, the collector current is 10 mA. If 95 per cent of the electrons emitted reach the collector, which of the following statements are true?
(a) The emitter current will be 8 mA
(b) The emitter current will be 10.53 mA
(c) The base current will be 0.53 mA
(d) The base current will be 2 mA
Show Answer & Explanation

Answer: (b) The emitter current will be 10.53 mA, (c) The base current will be 0.53 mA

Explanation:
1. \( I_C = 0.95\,I_E \Rightarrow I_E = \dfrac{10}{0.95} = 10.53 \) mA: (b).
2. \( I_B = I_E - I_C = 10.53 - 10 = 0.53 \) mA: (c).

Teacher's Note:
1. IE = IB + IC always holds for a transistor.
2. The fraction 0.95 is the current gain α.

Examination Note: Use IC = αIE first, then IB = IE − IC.

 

Question 13: In the depletion region of a diode
(a) there are no mobile charges
(b) equal number of holes and electrons exist, making the region neutral
(c) recombination of holes and electrons has taken place
(d) immobile charged ions exist
Show Answer & Explanation

Answer: (a) there are no mobile charges, (c) recombination of holes and electrons has taken place, (d) immobile charged ions exist

Explanation:
1. When the junction forms, electrons from the n-side and holes from the p-side diffuse across and recombine near the junction: (c).
2. This removes the mobile carriers from the region, leaving only the immobile positive donor ions on the n-side and negative acceptor ions on the p-side: (a) and (d).
3. The region is therefore not a mixture of equal numbers of holes and electrons, so (b) is not correct. It is the fixed ions, not free carriers, which create the electric field and the barrier.

Teacher's Note:
1. Depletion means depleted of mobile carriers.
2. The published key lists (a), (b), (d). Statement (b) contradicts (a), so recombination (c) is the statement that goes with (a) and (d).

Examination Note: Say that mobile carriers have recombined and only fixed ions remain.

 

Question 14: What happens during regulation action of a Zener diode?
(a) The current and voltage across the Zener remains fixed
(b) The current through the series resistance (Rs) changes
(c) The Zener resistance is constant
(d) The resistance offered by the Zener changes
Show Answer & Explanation

Answer: (b) The current through the series resistance (Rs) changes, (d) The resistance offered by the Zener changes

Explanation:
1. In the breakdown region the voltage across the Zener stays almost constant while the current through it changes widely.
2. When the input voltage or the load changes, the current through Rs changes, and the Zener resistance (V/I) changes as its current changes: (b) and (d). The Zener current is not fixed, so (a) is false.

Teacher's Note:
1. The Zener takes up the extra current, so the output voltage stays steady.
2. Its dynamic resistance in breakdown is very small.

Examination Note: State what stays fixed (voltage) and what changes (current and resistance).

 

Question 15: To reduce the ripples in a rectifier circuit with capacitor filter
(a) RL should be increased
(b) input frequency should be decreased
(c) input frequency should be increased
(d) capacitors with high capacitance should be used
Show Answer & Explanation

Answer: (a) RL should be increased, (c) input frequency should be increased, (d) capacitors with high capacitance should be used

Explanation:
1. For a full wave rectifier with a capacitor filter the ripple factor is \( r = \dfrac{1}{4\sqrt3\,\nu R_LC} \).
2. So r is inversely proportional to RL, to C and to the frequency ν. To reduce the ripple, RL should be increased (a), the frequency increased (c), and the capacitance increased (d).

Teacher's Note:
1. A large RC time constant means the capacitor discharges only a little between charging peaks.
2. A higher frequency gives the capacitor less time to discharge.

Examination Note: Quote the ripple factor formula and read off the three dependences.

 

Question 16: The breakdown in a reverse biased p-n junction is more likely to occur due to
(a) large velocity of the minority charge carriers if the doping concentration is small
(b) large velocity of the minority charge carriers if the doping concentration is large
(c) strong electric field in a depletion region if the doping concentration is small
(d) strong electric field in the depletion region if the doping concentration is large
Show Answer & Explanation

Answer: (a) large velocity of the minority charge carriers if the doping concentration is small, (d) strong electric field in the depletion region if the doping concentration is large

Explanation:
1. With light doping the depletion region is wide. Minority carriers are accelerated over a long distance, gain a large velocity and ionise atoms by collision, producing more carriers (avalanche breakdown): (a).
2. With heavy doping the depletion region is very thin, so even a small reverse voltage gives a very strong electric field that can pull electrons out of covalent bonds directly (Zener breakdown): (d).

Teacher's Note:
1. Avalanche breakdown: light doping. Zener breakdown: heavy doping.
2. A thin region means a large field E = V/d.

Examination Note: Name the two mechanisms and the doping level for each.

 

Very Short Answer Type Questions

Question 17. Why are elemental dopants for silicon or germanium usually chosen from group XIII or group XV?
Answer:
The dopant atom should be of nearly the same size as the Si or Ge atom, so that it does not distort the crystal lattice, and it should easily provide extra charge carriers.
Group XIII atoms (three valence electrons) and group XV atoms (five valence electrons) have sizes close to Si and Ge. A group XV atom forms four covalent bonds and leaves one free electron (n-type); a group XIII atom leaves one vacancy, a hole (p-type).
In simple words: Their atoms fit into the lattice and each adds one free electron or one hole.

Teacher's Note:
1. Group XIV elements have four valence electrons, so the dopant must have one more or one less.
2. Elements further from group XIV differ much more in size.

Examination Note: Mention both the size match and the one-extra-electron or one-hole result.

 

Question 18. Sn, C and Si, Ge are all group XIV elements. Yet, Sn is a conductor, C is an insulator while Si and Ge are semiconductors. Why?
Answer:
The conduction behaviour depends on the energy gap between the conduction band and the valence band.
Sn has an energy gap of about 0 eV (the bands overlap, so it is a conductor), C (diamond) has a gap of about 5.4 eV (a large gap, an insulator), while Si (1.1 eV) and Ge (0.7 eV) have moderate gaps and are semiconductors. The gap depends on the atomic size and bonding.
In simple words: A small or zero gap lets electrons move; a huge gap stops them; a medium gap gives a semiconductor.

Teacher's Note:
1. Bigger atoms have weaker bonds and a smaller gap.
2. At room temperature, only a medium gap material gets a few thermally excited carriers.

Examination Note: Quote the four gap values to support the statement.

 

Question 19. Can the potential barrier across a p-n junction be measured by simply connecting a voltmeter across the junction?
Answer:
No. A voltmeter has a very high resistance compared with the junction resistance of the depletion region, so it would draw no current and the barrier potential is not an emf that can be read this way.
In the unbiased junction there is no net current. The barrier potential is an internal potential difference, and the contact potentials at the metal leads cancel it in the external circuit.
In simple words: The barrier is built in inside the junction and cannot be read by a voltmeter placed across it.

Teacher's Note:
1. Contact potentials between the metal leads and semiconductor cancel the barrier voltage in a closed loop.
2. The junction has no source of energy to drive a current.

Examination Note: Give two reasons: no net current flows, and the contacts cancel the barrier.

 

Question 20. Draw the output waveform across the resistor in the given figure. The input waveform at A is shown beside the circuit.
AV0Rinput 0+1 V−1 VInput waveform at A
Answer:
The ideal diode conducts only when it is forward biased, that is, when the input is positive (+1 V). It then drops no voltage, so the full +1 V appears across R. When the input is negative (−1 V), the diode is reverse biased and no current flows, so the output across R is zero.
0+1 VtOutput across R
In simple words: The diode lets only the positive part of the input pass.

Teacher's Note:
1. This is a half wave rectifier with the output across the series resistor.
2. The input is a square wave, so the output is a series of rectangular pulses.

Examination Note: Draw the input and the output one above the other with the same time axis; label +1 V and 0.

 

Question 21. The amplifiers X, Y and Z are connected in series. If the voltage gains of X, Y and Z are 10, 20 and 30, respectively and the input signal is 1 mV peak value, then what is the output signal voltage (peak value) (i) if DC supply voltage is 10 V? (ii) if DC supply voltage is 5 V?
Answer:
Total gain \( = 10\times20\times30 = 6000 \). Output \( = 6000\times1\ \text{mV} = 6\ \text{V} \).
(i) With a 10 V supply, a 6 V peak output is possible (it is less than the supply), so the output peak is 6 V.
(ii) With a 5 V supply, the output cannot exceed the supply voltage, so the signal is clipped and the peak output is limited to about 5 V.
In simple words: Multiply the gains to get 6 V; a 5 V supply cannot give more than 5 V.

Teacher's Note:
1. Gains of amplifiers in series multiply.
2. An amplifier cannot deliver an output peak above its DC supply.

Examination Note: Show the product of gains and then compare the calculated output with the supply voltage.

 

Question 22. In a CE transistor amplifier, there is a current and voltage gain associated with the circuit. In other words there is a power gain. Considering power a measure of energy, does the circuit violate conservation of energy?
Answer:
No. The power gain of a CE amplifier is large, but the extra output power does not come from the input signal. It is supplied by the DC source (battery) connected to the collector circuit.
The transistor only controls how the DC power is converted into the amplified signal. The output power is always less than the total power taken from the DC source plus the input signal power, so energy is conserved.
In simple words: The amplifier does not create energy; the battery supplies the extra power.

Teacher's Note:
1. A transistor works like a tap: a small input signal controls a large flow supplied by the battery.
2. Some of the DC power is also lost as heat in the transistor.

Examination Note: Say clearly that the extra power is drawn from the DC supply.

 

Short Answer Type Questions

Question 23. (i) Name the type of a diode whose characteristics are shown in figure (a) and (b). (ii) What does the point P in fig. (a) represent? (iii) What does the points P and Q in fig. (b) represent?
I (μA)V (volt)P(a)IVQP(b)
Answer:
(i) Figure (a) is the characteristic of a Zener diode; figure (b) is that of a solar cell (photodiode in the photovoltaic mode).
(ii) The point P in fig. (a) is the Zener breakdown voltage, at which the reverse current rises sharply.
(iii) In fig. (b), Q is the point of zero voltage and negative (reverse) current: the solar cell is short circuited and the current is the short circuit current. P is the point of zero current at a positive voltage: the current is zero, so the voltage is the open circuit voltage.
In simple words: The Zener curve has a sharp reverse breakdown, and a solar cell curve lies in the fourth quadrant.

Teacher's Note:
1. A solar cell generates its own voltage, so there is current even at zero applied voltage.
2. Open circuit means no current, short circuit means no voltage across the cell.

Examination Note: Name the device, then say what each marked point means in one phrase.

 

Question 24. Three photo diodes D1, D2 and D3 are made of semiconductors having band gaps of 2.5 eV, 2 eV and 3 eV, respectively. Which ones will be able to detect light of wavelength 6000 Å?
Answer:
Photon energy \( E = \dfrac{hc}{\lambda} = \dfrac{6.6\times10^{-34}\times3\times10^{8}}{6000\times10^{-10}\times1.6\times10^{-19}} \) eV \( = 2.06 \) eV.
A photodiode detects light only if the photon energy is greater than its band gap. D1 (2.5 eV) and D3 (3 eV) have gaps larger than 2.06 eV; D2 has a gap of 2 eV, which is smaller.
Only D2 can detect this light.
In simple words: The photon must have more energy than the band gap.

Teacher's Note:
1. Use hc = 12400 eV Å for a quick check: 12400/6000 = 2.07 eV.
2. Light of lower energy than the gap cannot free any electron-hole pair.

Examination Note: Calculate the photon energy in eV and compare it with each gap.

 

Question 25. None
AVR1R2
Answer:
The base current is \( I_B = \dfrac{V_{BB} - V_{BE}}{R_1} \). On increasing R1, IB decreases.
The ammeter measures the collector current, \( I_C = \beta I_B \). As IB decreases, IC decreases, so the ammeter reading decreases.
The voltmeter reads the voltage across R2, \( V = I_C R_2 \). Since IC decreases, the voltmeter reading also decreases.
In simple words: More base resistance means less base current, hence less collector current and a smaller drop across R2.

Teacher's Note:
1. IC is β times IB while the transistor is in the active region.
2. The ammeter is in the collector circuit and the voltmeter is across the collector resistor.

Examination Note: Chain the effects: R1 up, IB down, IC down, voltage across R2 down.

 

Question 26. Two car garages have a common gate which needs to open automatically when a car enters either of the garages or cars enter both. Devise a circuit that resembles this situation using diodes for this situation.
Answer:
The gate must open if a car is in garage A, in garage B, or in both. This is the OR operation, so the circuit is an OR gate made of two diodes whose anodes are the inputs A and B and whose cathodes are joined to the output C, which is connected to earth through a resistor.
ABCDiode circuitOR gateABC
If either A or B is at the high level, the corresponding diode conducts and C becomes high. If both are low, C stays low. The truth table is:

ABC
000
011
101
111

In simple words: Two diodes joined at the output make an OR gate: the gate opens if either garage senses a car.

Teacher's Note:
1. In a diode OR gate, the diodes are forward biased by a high input.
2. The resistor to earth keeps the output low when no input is high.

Examination Note: Draw the circuit, name the gate (OR) and give the truth table.

 

Question 27. How would you set up a circuit to obtain NOT gate using a transistor?
Answer:
A NOT gate has one input and one output, and the output is the opposite of the input, Y = Ā. It cannot be made with diodes, but it can be made with a transistor in the CE configuration.
+5 VARBYRCE
The input A is connected to the base through a resistor RB, the emitter is earthed and the collector is connected to a 5 V supply through a resistor RC. The output Y is the voltage at the collector with respect to earth.
RB and RC are chosen so that: when the input is low (0 V) the transistor is cut off, no collector current flows and Y is high (about 5 V); when the input is high (5 V) the transistor is saturated, the collector is almost at earth potential and Y is low.

AY
01
10

In simple words: A transistor used as a switch inverts the signal.

Teacher's Note:
1. Low input: cut off, output high. High input: saturation, output low.
2. The transistor amplifier is used as an inverter because the collector voltage falls as the base voltage rises.

Examination Note: Draw the circuit and write the truth table; state the two operating states of the transistor.

 

Question 28. Explain why elemental semiconductor cannot be used to make visible LEDs.
Answer:
The band gaps of the elemental semiconductors are small (Si 1.1 eV, Ge 0.7 eV). The energy of the emitted photons is equal to the band gap, so the emission lies in the infrared region and not in the visible region (about 1.8 eV to 3.1 eV). Compound semiconductors with larger gaps (for example GaAsP or GaP) are used for visible LEDs.
In simple words: Silicon and germanium have small band gaps, so the light they give out is infrared and cannot be seen.

Teacher's Note:
1. Visible light has photon energy of about 1.8 to 3.1 eV.
2. Also, Si and Ge are indirect band gap materials, which makes them poor light emitters.

Examination Note: Link photon energy to the band gap and give the visible energy range.

 

Question 29. Write the truth table for the circuit shown in the figure given below. Name the gate that the circuit resembles.
+5 VVoD1D2AB
Answer:
The circuit resembles an AND gate: the output is high (about 5 V) only when both inputs are high. If either input is low, the corresponding diode conducts and pulls the output down to low. The Boolean expression is V0 = A·B.
ABV0 = A·B
000
010
100
111

In simple words: Both inputs must be high for the output to be high, so it is an AND gate.

Teacher's Note:
1. When both diodes are reverse biased (inputs high), no current flows through R and V0 is 5 V.
2. Any low input makes its diode conduct, grounding the output.

Examination Note: State the gate, the Boolean expression and the truth table.

 

Question 30. A Zener of power rating 1 W is to be used as a voltage regulator. If Zener has a breakdown of 5 V and it has to regulate voltage which fluctuates between 3 V and 7 V, what should be the value of Rs for safe operation (see figure)?
RsUnregulatedvoltageRegulatedvoltage
Answer:
Maximum current through the Zener: \( I_{Z,max} = \dfrac{P}{V_Z} = \dfrac{1}{5} = 0.2 \) A.
The worst case is the highest supply voltage, 7 V, when the voltage across Rs is \( 7 - 5 = 2 \) V and the current should not exceed 0.2 A: \( R_s = \dfrac{V_{max} - V_Z}{I_{Z,max}} = \dfrac{2}{0.2} = 10\ \Omega \).
Rs should be at least about 10 Ω (with no load connected). Note that when the input falls to 3 V, which is below the 5 V breakdown voltage, the Zener cannot regulate.
In simple words: Choose Rs so that the Zener does not exceed its 0.2 A limit at 7 V.

Teacher's Note:
1. The same series resistor must also supply enough current at the minimum input voltage when a load is present.
2. Power P = VZIZ limits the Zener current.

Examination Note: Find IZ from the power rating first, then Rs from the voltage across it at the maximum input.

 

Long Answer Type Questions

Question 31. If each diode in the figure has a forward bias resistance of 25 Ω and infinite resistance in reverse bias, what will be the values of the currents I1, I2, I3 and I4?
125 ΩAB125 ΩCD125 ΩEF5 V25 ΩGHI1I4I3I2
Answer:
The diode in branch CD is reverse biased and has infinite resistance, so I3 = 0. The diodes in branches AB and EF are forward biased.
Resistance of branch AB = 25 + 125 = 150 Ω; of branch EF = 25 + 125 = 150 Ω. These are in parallel: 1/R′ = 1/150 + 1/150, so R′ = 75 Ω.
Total resistance = 75 + 25 = 100 Ω, so I1 = 5/100 = 0.05 A.
The two branches are equal, so I4 = I2 = I1/2: I2 = I4 = 0.025 A, and I3 = 0.
In simple words: One diode is blocked, the other two share the current equally.

Teacher's Note:
1. I1 = I2 + I3 + I4 by Kirchhoff's current law.
2. The 25 Ω in the battery branch is in series with the parallel combination.

Examination Note: Identify the blocked branch first, then combine resistances step by step.

 

Question 32. In the circuit shown in the figure, when the input voltage of the base resistor is 10 V, VBE is zero and VCE is also zero. Find the values of IB, IC and β.
10 VViRB400 kΩRC3 kΩ
Answer:
With VBE = 0, the whole 10 V is across RB: \( I_B = \dfrac{10}{400\times10^{3}} = 25\ \mu\text{A} \).
With VCE = 0, the whole 10 V is across RC: \( I_C = \dfrac{10}{3\times10^{3}} = 3.33\ \text{mA} \).
\( \beta = \dfrac{I_C}{I_B} = \dfrac{3.33\times10^{-3}}{25\times10^{-6}} \approx 133 \).
In simple words: IB = 25 μA, IC = 3.33 mA, β ≈ 133.

Teacher's Note:
1. VCE = 0 means that the transistor is at the edge of saturation, so β here is the ratio IC/IB at this point.
2. Always convert kΩ to Ω and mA to A when substituting.

Examination Note: Apply Ohm's law across each resistor and then take the ratio of the currents.

 

Question 33. Draw the output signals C1 and C2 in the given combination of gates, for the input waveforms shown.
ABC1ABC2 AB012345t (s)
Answer:
First circuit. Each of the first two gates has its two inputs joined, so it works as a NOT gate: E = Ā and F = B̄. The third gate is a NAND of E and F, giving (E·F)‾ = A + B, and the last gate (inputs joined) inverts it again. So C1 = E·F = Ā·B̄, which is a NOR operation: C1 = 1 only when A = B = 0.
ABE = ĀF = B̄C1 = Ā·B̄
00111
10010
01100
11000

Second circuit. Each of the first two gates is a NOR with joined inputs, so it works as a NOT gate: E = Ā and F = B̄. The last NOR gate gives C2 = (E + F)‾ = (Ā + B̄)‾ = A·B, which is an AND operation: C2 = 1 only when A = B = 1.
ABE = ĀF = B̄C2 = A·B
00110
10010
01100
11001

Waveforms. A is high for 0 to 2 s and 3 to 4 s; B is high for 1 to 3 s. C1 is high only when both are low, which is for 4 to 5 s. C2 is high only when both are high, which is for 1 to 2 s.
ABC1C2012345t (s)
In simple words: C1 is high when both inputs are low (NOR); C2 is high when both inputs are high (AND).

Teacher's Note:
1. A two-input NAND or NOR gate with its inputs joined acts as a NOT gate.
2. Read each time interval of 1 s separately and look up the truth table.

Examination Note: Build the truth table first, then read off the outputs for each second of the input waveforms.

 

Question 34. Consider the circuit arrangement shown in the figure for studying input and output characteristics of n-p-n transistor in CE configuration. Select the values of RB and RC for a transistor whose VBE = 0.7 V, so that the transistor is operating at point Q as shown in the characteristics. Given that the input impedance of the transistor is very small and VCC = VBB = 16 V, also find the voltage gain and power gain of the circuit making appropriate assumptions.
RBRCVBBVCCICVCEVBEIC (mA)VCE4 mA8 VQIB = 30 μA
Answer:
From the graph at Q: VCE = 8 V, IC = 4 mA and IB = 30 μA.
Output loop: \( V_{CC} = I_CR_C + V_{CE} \Rightarrow R_C = \dfrac{16-8}{4\times10^{-3}} = 2\ \text{k}\Omega \).
Input loop: \( V_{BB} = I_BR_B + V_{BE} \Rightarrow R_B = \dfrac{16-0.7}{30\times10^{-6}} = 510\ \text{k}\Omega \).
Current gain \( \beta = \dfrac{I_C}{I_B} = \dfrac{4\times10^{-3}}{30\times10^{-6}} \approx 133 \).
Assuming the input resistance is RB and the output (load) resistance is RC: voltage gain \( = \beta\dfrac{R_C}{R_B} = 133\times\dfrac{2\times10^{3}}{510\times10^{3}} \approx 0.52 \). Power gain \( = \beta\times\text{voltage gain} = 133\times0.52 \approx 69 \).
In simple words: RC = 2 kΩ, RB = 510 kΩ, voltage gain about 0.52, power gain about 69.

Teacher's Note:
1. The gain of an amplifier is only that of a small signal; here the answer depends on the assumption that the input resistance is RB.
2. Power gain = current gain × voltage gain.

Examination Note: State the assumption about input and output resistances before computing the gains.

 

Question 35. Assuming the ideal diode, draw the output waveform for the circuit given in fig. (a), explain the waveform. The input is 20 sin ωt.
20 sin ωtR5 V
Answer:
For an ideal diode the forward resistance is zero and the reverse resistance is infinite.
Input between −20 V and +5 V: the diode is reverse biased (its anode is at a lower potential than the 5 V battery side), behaves as an open circuit, and no current flows through R. The input appears unchanged across the output terminals. For the negative half cycle the output follows the input, down to −20 V.
Input above +5 V: the diode becomes forward biased and conducts. Its resistance is zero, so the output is held at +5 V and the excess voltage appears across R. The positive peaks are therefore clipped at +5 V.
+5 V+20 V−20 V0tOutput voltageT/2T3T/22T
The circuit is a clipper (limiter): it removes the part of the positive half cycle above 5 V.
In simple words: The output is the input waveform with its tops cut off at +5 V.

Teacher's Note:
1. The diode conducts only when the input is more than 5 V, because of the series battery.
2. With an ideal diode and a 20 V peak input, the negative half cycle reaches −20 V.

Examination Note: Draw the sine wave with a flat top at +5 V and write the condition for the diode to conduct.

 

Question 36. Suppose a n-type wafer is created by doping Si crystal having 5 × 1028 atoms/m3 with 1 ppm concentration of As. On the surface 200 ppm boron is added to create 'p' region in this wafer. Considering ni = 1.5 × 1016 m−3, (i) calculate the densities of the charge carriers in the n and p regions. (ii) Comment which charge carriers would contribute largely for the reverse saturation current when diode is reverse biased.
Answer:
(i) n-region. Electrons: \( n_e = N_D = \dfrac{1}{10^6}\times5\times10^{28} = 5\times10^{22}\ \text{m}^{-3} \). Holes (minority): \( n_h = \dfrac{n_i^2}{n_e} = \dfrac{(1.5\times10^{16})^2}{5\times10^{22}} = 4.5\times10^{9}\ \text{m}^{-3} \).
p-region. Holes: \( n_h = N_A = \dfrac{200}{10^6}\times5\times10^{28} = 1\times10^{25}\ \text{m}^{-3} \). Electrons (minority): \( n_e = \dfrac{n_i^2}{n_h} = \dfrac{(1.5\times10^{16})^2}{10^{25}} = 2.25\times10^{7}\ \text{m}^{-3} \).
(ii) In reverse bias, the current is due to the minority carriers: holes of the n-region (4.5 × 109 m−3) and electrons of the p-region (2.25 × 107 m−3). The holes of the n-region are far more numerous, so they contribute most of the reverse saturation current.
In simple words: Majority carriers equal the doping density; minority carriers follow from nenh = ni2. The n-region minority holes dominate the reverse current.

Teacher's Note:
1. The p-region is formed on the n-type wafer, and the net acceptor density is 1 × 1025 − 5 × 1022, which is very nearly 1 × 1025 m−3.
2. The value is 2.25 × 107 m−3.

Examination Note: Use ppm × atom density for the majority carriers and ni2 for the minority carriers; then compare the two minority densities.

 

Question 37. An X-OR gate has the following truth table. It is represented by the following logic relation Y = Ā·B + A·B̄. Build this gate using AND, OR and NOT gates.
Answer:

ABY
000
011
101
110

Write Y = Y1 + Y2, where Y1 = Ā·B and Y2 = A·B̄.
Y1 is the output of AND gate I, whose inputs are Ā (A passed through a NOT gate) and B. Y2 is the output of AND gate II, whose inputs are A and B̄ (B passed through a NOT gate). The two outputs feed an OR gate III, whose output is Y.
ABYIIIIII
In simple words: Two NOT gates, two AND gates and one OR gate build the XOR gate.

Teacher's Note:
1. XOR is high when the inputs differ.
2. Check: for A = B = 1 both AND gates get a 0 input, so Y = 0.

Examination Note: Write the expression as a sum of two products and draw one gate for each term.

 

Question 38. Consider a box with three terminals on top of it as shown in the figure. Three components, namely two germanium diodes and one resistor, are connected across these three terminals in some arrangement. A student connects any two of the three terminals in the circuit shown in fig. (b) and obtains the current-voltage graphs (c) to (h) given below.
ABC(a)mAVBox terminals(b) VI(c) A +, B −VI(d) A −, B +0.7 V1/slope = 1000 ΩVI(e) B −, C +0.7 VVI(f) B +, C −0.7 VVI(g) A +, C −VI(h) A −, C +1.4 V From these graphs of current-voltage characteristic shown in fig. (c) to (h), determine the arrangement of components between A, B and C.
Answer:
(c) Between A (+) and B (−), the characteristic is a reverse one (a tiny current). So A is connected to the n-side of a p-n junction I and B to its p-side, with a resistance in series.
(d) With A (−) and B (+), the characteristic is forward: the knee voltage is 0.7 V and 1/slope = 1000 Ω. So the p-n junction I is forward biased and a resistor R of 1 kΩ is in series with it between A and B.
(e) With B (−) and C (+), a forward characteristic with a knee at 0.7 V. So the p-side of a second junction II is connected to C and its n-side to B.
(f), (g), (h) agree with this arrangement: with B (+) and C (−) junction II is reverse biased; with A (+) and C (−) the junctions are back to back, and one of them is always reverse biased, so the current is tiny; with A (−) and C (+) both junctions are forward biased in series, so the knee is at 0.7 + 0.7 = 1.4 V.
The arrangement is: A and R in series, then p-n I (its n-side towards A), the common point B, and p-n II (its n-side towards B), then C.
ARBCp-n Ip-n II
In simple words: Two diodes pointing the same way along A, B, C, with a 1 kΩ resistor in series with the first diode.

Teacher's Note:
1. Two germanium diodes in series have a combined knee voltage of twice the single value, which is why graph (h) has 1.4 V.
2. A series pair of diodes facing opposite ways blocks both polarities, which is why (g) looks reverse.

Examination Note: Go through the graphs one by one and fix the polarity of each junction and the resistor.

 

Question 39. For the transistor circuit shown in the figure, evaluate VE, RB, RE, given IC = 1 mA, VCE = 3 V, VBE = 0.5 V and VCC = 12 V, β = 100.
VCC = 12 VRBRC= 7.8 kΩ20 kΩREVC
Answer:
Taking \( I_E \approx I_C = 1 \) mA: \( V_{CC} = I_C(R_C + R_E) + V_{CE} \Rightarrow 12 = 1\times10^{-3}(7800 + R_E) + 3 \Rightarrow R_C + R_E = 9\ \text{k}\Omega \).
So RE = 9 − 7.8 = 1.2 kΩ, and VE = IERE = 1 mA × 1.2 kΩ = 1.2 V.
Base voltage: \( V_B = V_E + V_{BE} = 1.2 + 0.5 = 1.7 \) V. Current through the 20 kΩ resistor: \( I = \dfrac{1.7}{20\times10^{3}} = 0.085 \) mA.
Base current: \( I_B = \dfrac{I_C}{\beta} = 0.01 \) mA. The current through RB is \( 0.085 + 0.01 = 0.095 \) mA, and the voltage across it is \( 12 - 1.7 = 10.3 \) V.
\( R_B = \dfrac{10.3}{0.095\ \text{mA}} \approx 108\ \text{k}\Omega \).
In simple words: VE = 1.2 V, RE = 1.2 kΩ and RB is about 108 kΩ.

Teacher's Note:
1. In the printed figure the lower resistor is marked 200 kΩ in one view; the question's figure and the working both use 20 kΩ.
2. Apply KVL to the output loop first to get RE, then to the base divider.

Examination Note: Use the collector loop for RE and VE, then the base divider for RB; write the base current in the divider.

 

Question 40. In the circuit shown in fig. (a), find the value of RC. (β = 100, VBE = 0.5 V, VCE = 3 V, RE = 1 kΩ, VCC = 12 V.)
VCC = 12 VRB100 kΩRC20 kΩRE= 1 kΩ
Answer:
The base is fed from a divider of 100 kΩ (to VCC) and 20 kΩ (to earth). Its Thevenin equivalent is \( V_{th} = 12\times\dfrac{20}{120} = 2 \) V, \( R_{th} = \dfrac{100\times20}{120} = 16.7\ \text{k}\Omega \).
Base loop: \( V_{th} = I_BR_{th} + V_{BE} + I_ER_E \) with \( I_E = (\beta+1)I_B = 101\,I_B \): \( 2 = I_B(16.7 + 101\times1)\times10^{3} + 0.5 \Rightarrow I_B = \dfrac{1.5}{117.7\times10^{3}} \approx 12.7\ \mu\text{A} \).
\( I_C = \beta I_B \approx 1.27 \) mA and \( I_E \approx 1.29 \) mA.
Collector loop: \( V_{CC} = I_CR_C + V_{CE} + I_ER_E \Rightarrow 12 = 1.27R_C + 3 + 1.29 \Rightarrow R_C \approx \dfrac{7.7}{1.27} \approx 6\ \text{k}\Omega \).
In simple words: RC is about 6 kΩ.

Teacher's Note:
1. A value of 0.56 kΩ would be wrong: it treats the 20 kΩ base divider resistor as if it carried the base current and mixes 80 kΩ into the loop.
2. With IE ≈ IC, the quick estimate RC + RE = (12 − 3)/1.27 mA = 7.1 kΩ gives the same 6 kΩ.

Examination Note: Replace the base divider by its Thevenin equivalent, get IB, then use the collector loop.