These NCERT Exemplar solutions for Class 12 Physics Chapter 7, Alternating Current, give step-by-step answers to all 31 questions: 7 MCQs, 6 multiple-correct MCQs, 7 very short, 6 short and 5 long answer questions. They cover rms and peak values, reactance and impedance, phase and power factor, series and parallel L-C-R circuits, resonant frequency, quality factor and bandwidth, transformers and the transmission of power. Each answer is followed by a short Teacher's Note to build understanding and an Examination Note on how to present the answer for better marks.
Multiple Choice Questions (MCQs)
(a) \( 5\sqrt{2} \) A
(b) \( 5\sqrt{\dfrac{3}{2}} \) A
(c) \( \dfrac{5}{6} \) A
(d) \( \dfrac{5}{\sqrt{2}} \) A
Show Answer & Explanation
Answer: (b) \( 5\sqrt{\dfrac{3}{2}} \) A
Explanation:
1. Peak current: \( I_0 = \sqrt{2}\,I_{rms} = 5\sqrt{2}\) A. Measuring time from the instant the current is zero, \( I = I_0 \sin\omega t \).
2. \( \omega t = 2\pi \nu t = 2\pi \times 50 \times \dfrac{1}{300} = \dfrac{\pi}{3} \).
3. \( I = 5\sqrt{2}\sin\dfrac{\pi}{3} = 5\sqrt{2}\times\dfrac{\sqrt{3}}{2} = 5\sqrt{\dfrac{3}{2}} \approx 6.1\ \text{A} \).
Teacher's Note:
1. The instant when the current is zero is taken as t = 0, so use the sine form.
2. The 'rms' given is the effective value; always convert it into the peak value before using I = I0 sin ωt.
Examination Note: Write I0 = √2 Irms first, then compute ωt in radians (π/3). The value of sin 60° is √3/2.
(a) zero
(b) Xg
(c) − Xg
(d) Rg
Show Answer & Explanation
Answer: (c) − Xg
Explanation:
1. The total impedance of the circuit is \( Z = (R_g + R_g) + j(X_g + X_L) \).
2. The power delivered to the load is \( P = I^2 R_g = \dfrac{V^2 R_g}{(2R_g)^2 + (X_g + X_L)^2} \).
3. This is a maximum when the denominator is least, i.e. when \( X_g + X_L = 0 \), so \( X_L = -X_g \). The two reactances cancel.
Teacher's Note:
1. Maximum power transfer needs the net reactance of the whole circuit to be zero; only the resistance is then left.
2. A negative XL means the load is capacitive when the generator is inductive.
Examination Note: State the condition: total reactance = 0 for maximum current, hence XL = −Xg.
(a) input voltage cannot be AC voltage, but a DC voltage
(b) maximum input voltage is 220 V
(c) the meter reads not v but \( \langle v^2 \rangle \) and is calibrated to read \( \sqrt{\langle v^2 \rangle} \)
(d) the pointer of the meter is stuck by some mechanical defect
Show Answer & Explanation
Answer: (c) the meter reads not v but \( \langle v^2 \rangle \) and is calibrated to read \( \sqrt{\langle v^2 \rangle} \)
Explanation:
1. The mean of an alternating voltage over a cycle is zero, so a meter cannot simply read the average of v.
2. An AC voltmeter responds to the mean value of v² (for example through the heating effect) and is calibrated to show \( \sqrt{\langle v^2 \rangle} \), the rms value. So the steady reading of 220 V is the rms value of the mains voltage.
3. The peak value is 220√2 ≈ 311 V, so (b) is wrong; the mains is AC, so (a) is wrong.
Teacher's Note:
1. The mains '220 V' is always the rms value.
2. Moving-coil meters would read zero for AC; AC meters are therefore calibrated for the rms value.
Examination Note: Say that the meter reads ⟨v²⟩ and is calibrated as √⟨v²⟩, the rms value; mention that the peak is 311 V.
(a) the generator frequency should be reduced
(b) another capacitor should be added in parallel to the first
(c) the iron core of the inductor should be removed
(d) dielectric in the capacitor should be removed
Show Answer & Explanation
Answer: (b) another capacitor should be added in parallel to the first
Explanation:
1. The resonant frequency is \( \nu_0 = \dfrac{1}{2\pi\sqrt{LC}} \). To reduce it, L or C must be increased.
2. Adding another capacitor in parallel increases the total capacitance, so the resonant frequency goes down (b).
3. Removing the iron core decreases L and removing the dielectric decreases C, so both raise the resonant frequency. Changing the generator frequency does not change the resonant frequency of the circuit; it only changes how far the driving frequency is from the resonant frequency.
Teacher's Note:
1. Resonant frequency is a property of L and C, not of the generator.
2. Capacitors in parallel add: C = C1 + C2.
Examination Note: Use ν0 = 1/(2π√LC) and decide for each option whether L or C increases or decreases.
(a) R = 20 Ω, L = 1.5 H, C = 35 μF
(b) R = 25 Ω, L = 2.5 H, C = 45 μF
(c) R = 15 Ω, L = 3.5 H, C = 30 μF
(d) R = 25 Ω, L = 1.5 H, C = 45 μF
Show Answer & Explanation
Answer: (c) R = 15 Ω, L = 3.5 H, C = 30 μF
Explanation:
1. Better tuning (sharper tuning) needs a high quality factor \( Q = \dfrac{1}{R}\sqrt{\dfrac{L}{C}} \).
2. (a) \( Q = \dfrac{1}{20}\sqrt{\dfrac{1.5}{35\times10^{-6}}} \approx 10.4 \); (b) \( Q \approx 9.4 \); (c) \( Q = \dfrac{1}{15}\sqrt{\dfrac{3.5}{30\times10^{-6}}} \approx 22.8 \); (d) \( Q \approx 7.3 \).
3. Option (c) has the largest Q (low R, high L, low C), so it gives the best tuning.
Teacher's Note:
1. A high Q means a narrow bandwidth, so the circuit selects one station and rejects the neighbouring ones.
2. Compare L/C and R together; do not decide from only one quantity.
Examination Note: Write the formula for Q and show the values for all four, or argue that low R and high L/C are needed. Either way, state clearly that Q must be maximum.
(a) 8 W
(b) 12 W
(c) 14.4 W
(d) 18 W
Show Answer & Explanation
Answer: (c) 14.4 W
Explanation:
1. Impedance: \( Z = \sqrt{R^2 + X_L^2} = \sqrt{4 + 1} = \sqrt{5}\ \Omega \).
2. \( I_{rms} = \dfrac{6}{\sqrt{5}} \) A and \( \cos\phi = \dfrac{R}{Z} = \dfrac{2}{\sqrt{5}} \).
3. \( P = V_{rms}I_{rms}\cos\phi = 6\times\dfrac{6}{\sqrt{5}}\times\dfrac{2}{\sqrt{5}} = \dfrac{72}{5} = 14.4\ \text{W} \). Check: \( I^2R = \dfrac{36}{5}\times 2 = 14.4 \) W.
Teacher's Note:
1. Power is dissipated only in the resistor, so P = I²R.
2. Do not use V²/R = 18 W: the full 6 V does not appear across the resistor.
Examination Note: Write the answer as P = I²R_rms; this avoids the power-factor step and gives a quick check.
(a) \( 1/\sqrt{2} \) A
(b) \( \sqrt{2} \) A
(c) 2 A
(d) \( 2\sqrt{2} \) A
Show Answer & Explanation
Answer: (a) \( 1/\sqrt{2} \) A
Explanation:
1. Secondary current (rms): \( I_s = \dfrac{P}{V_s} = \dfrac{12}{24} = 0.5\ \text{A} \).
2. Peak current: \( I_0 = \sqrt{2}\,I_s = 0.5\sqrt{2} = \dfrac{1}{\sqrt{2}}\ \text{A} \approx 0.71\ \text{A} \).
Teacher's Note:
1. The 24 V and 12 W are rms/average values. Convert the current to its peak value at the end.
2. A bulb is a pure resistance, so P = Vrms Irms.
Examination Note: Find the rms current from P = VI and multiply by √2 for the peak value.
Multiple Choice Questions (More Than One Option)
(a) Inductor and capacitor
(b) Resistor and inductor
(c) Resistor and capacitor
(d) Resistor, inductor and capacitor
Show Answer & Explanation
Answer: (a) Inductor and capacitor, (d) Resistor, inductor and capacitor
Explanation:
1. \( X_L = 2\pi\nu L \) increases with frequency and \( X_C = \dfrac{1}{2\pi\nu C} \) decreases with it.
2. For a series circuit containing both L and C, \( Z = \sqrt{R^2 + (X_L - X_C)^2} \) falls to a minimum at the resonant frequency \( \nu_0 \) and then rises again. So the current first rises to a maximum and then falls.
3. A resistor with only an inductor has a current that falls steadily with frequency; with only a capacitor it rises steadily. So the circuit must contain both L and C: (a) or (d).
Teacher's Note:
1. The peak in the current is the resonant peak.
2. Both L and C are needed; R only decides how sharp the peak is.
Examination Note: Mention the resonant frequency and the opposing behaviour of XL and XC with frequency.
(a) Only resistor
(b) Resistor and an inductor
(c) Resistor and a capacitor
(d) Only a capacitor
Show Answer & Explanation
Answer: (c) Resistor and a capacitor, (d) Only a capacitor
Explanation:
1. Current increases with frequency when the opposition to current decreases with frequency.
2. The capacitive reactance \( X_C = \dfrac{1}{2\pi\nu C} \) decreases with frequency. So a capacitor alone, or a resistor with a capacitor (\( Z = \sqrt{R^2 + X_C^2} \) decreases), gives a larger current at higher frequency: (c) and (d).
3. A resistor alone has a frequency-independent impedance, and a resistor with an inductor has an impedance that increases with frequency (so the current decreases).
Teacher's Note:
1. Inductors resist rapid changes (high frequency); capacitors pass them easily.
2. A pure resistor is independent of frequency.
Examination Note: Decide using the sign of the change of XL and XC with frequency. A one-line reason for each rejected option is enough.
(a) For a given power level, there is a lower current
(b) Lower current implies less power loss
(c) Transmission lines can be made thinner
(d) It is easy to reduce the voltage at the receiving end using step-down transformers
Show Answer & Explanation
Answer: (a) For a given power level, there is a lower current, (b) Lower current implies less power loss, (c) Transmission lines can be made thinner, (d) It is easy to reduce the voltage at the receiving end using step-down transformers
Explanation:
1. For a given power P = VI, a higher voltage means a lower current: (a) is correct.
2. The loss in the lines is \( I^2R \), so a lower current implies much less loss: (b) is correct.
3. With a smaller current the line can be made of a thinner wire (larger R) for the same loss, since \( I^2R \) stays small: (c) is correct.
4. AC voltages can be stepped down easily and efficiently by transformers at the receiving end: (d) is correct.
Teacher's Note:
1. Doubling the voltage halves the current and cuts the loss to a quarter.
2. This is why the national grid works with alternating voltage and transformers.
Examination Note: Use the three linked ideas, P = VI, loss = I²R and the use of transformers, and tick all four statements with a reason each.
(a) Here, the power factor cos φ ≥ 0, P ≥ 0
(b) The driving force can give no energy to the oscillator (P = 0) in some cases
(c) The driving force cannot syphon out (P < 0) the energy out of oscillator
(d) The driving force can take away energy out of the oscillator
Show Answer & Explanation
Answer: (a) Here, the power factor cos φ ≥ 0, P ≥ 0, (b) The driving force can give no energy to the oscillator (P = 0) in some cases, (c) The driving force cannot syphon out (P < 0) the energy out of oscillator
Explanation:
1. Power factor \( \cos\phi = \dfrac{R}{Z} \). Since R ≥ 0 and Z > 0, \( \cos\phi \geq 0 \) and therefore \( P \geq 0 \): (a) is correct.
2. If R = 0 (a pure inductor, a pure capacitor or an ideal L-C circuit), cos φ = 0 and P = 0: the source gives no net energy, which is (b).
3. Because P is never negative, the source cannot take energy out of the oscillator: (c) is correct and (d) is wrong.
Teacher's Note:
1. Energy only flows from the source into the resistor (as heat) on average.
2. In a reactive circuit the energy goes back and forth, but there is no net transfer.
Examination Note: Use cos φ = R/Z ≥ 0 to settle all four options at once.
(a) the maximum voltage between plates is 220 V
(b) the current is in phase with the applied voltage
(c) the charge on the plates is in phase with the applied voltage
(d) power delivered to the capacitor is zero
Show Answer & Explanation
Answer: (c) the charge on the plates is in phase with the applied voltage, (d) power delivered to the capacitor is zero
Explanation:
1. The 220 V is the rms value, so the maximum voltage is \( 220\sqrt{2} \approx 311 \) V: (a) is wrong.
2. For a capacitor the current leads the voltage by 90°, so (b) is wrong.
3. The charge on the plates is \( q = CV \), so q is always in phase with v: (c) is correct.
4. The phase difference between voltage and current is 90°, so \( P_{av} = V_{rms}I_{rms}\cos 90^\circ = 0 \). The capacitor takes energy in one quarter-cycle and returns it in the next: (d) is correct.
Teacher's Note:
1. Voltage across a capacitor lags the current by 90°.
2. An ideal capacitor does not dissipate energy.
Examination Note: Remember that 220 V is rms. State the phase relation and average power for a capacitor: current leads by 90°, Pav = 0.
(a) zero average current
(b) 220 V average voltage
(c) voltage and current out of phase by 90°
(d) voltage and current possibly differing in phase φ such that \( |\phi| < \dfrac{\pi}{2} \)
Show Answer & Explanation
Answer: (a) zero average current, (d) voltage and current possibly differing in phase φ such that \( |\phi| < \dfrac{\pi}{2} \)
Explanation:
1. Household supply is AC, whose average value over a cycle is zero for both current and voltage, so (a) is correct and (b) is wrong (220 V is the rms value).
2. The line and the appliances together have some resistance, so the power factor \( \cos\phi = R/Z \) is not zero. A 90° phase difference would mean no power could be delivered, so (c) is wrong.
3. The phase difference is therefore less than 90°: \( |\phi| < \pi/2 \), which is (d).
Teacher's Note:
1. Average of a sine wave over a full cycle is zero.
2. If the phase difference were 90°, the line would carry no net power.
Examination Note: Distinguish average from rms values and say why φ cannot be 90° when power is being delivered.
Very Short Answer Type Questions
Question 14. If an L-C circuit is considered analogous to a harmonically oscillating spring-block system, which energy of the L-C circuit would be analogous to potential energy and which one analogous to kinetic energy?
Answer:
In an L-C circuit the charge q oscillates between the capacitor and the inductor, just as the displacement x of a block oscillates under a spring.
The electrostatic energy stored in the capacitor, \( \dfrac{1}{2}\dfrac{q^2}{C} \), is analogous to the potential energy \( \dfrac{1}{2}kx^2 \) of the spring.
The magnetic energy of the inductor, \( \dfrac{1}{2}LI^2 \), is analogous to the kinetic energy \( \dfrac{1}{2}mv^2 \) of the block.
In simple words: Capacitor energy plays the role of potential energy (stored position), and inductor energy plays the role of kinetic energy (energy of motion of charges).
Teacher's Note:
1. The correspondence is q ↔ x, current I ↔ velocity v, L ↔ m, 1/C ↔ k.
2. Total energy of an ideal L-C circuit stays constant, like the total energy of the block.
Examination Note: Give the mapping in a table-like line: q ↔ x, I ↔ v, L ↔ m, 1/C ↔ k. It answers the question and shows the full analogy.
Answer:
At very high frequencies, the inductive reactance \( X_L = 2\pi\nu L \to \infty \) and the capacitive reactance \( X_C = \dfrac{1}{2\pi\nu C} \to 0 \).
An element of very large reactance behaves as an open circuit, and an element of zero reactance behaves as a short circuit (a wire). So C1 and C2 are replaced by wires and L1 and L2 are removed (open).
With L2 open, R2 carries no current. The path is: source, R1, the wire in place of C1, the wire in place of C2, then R3 and back to the source. The equivalent circuit is R1 in series with R3 (shown below).
Effective impedance Z = R1 + R3
In simple words: At very high frequencies capacitors act like wires and inductors like breaks in the circuit, so only R1 and R3 remain, in series.
Teacher's Note:
1. At very low frequencies (or DC) the roles reverse: capacitors become open circuits and inductors become wires.
2. Resistors do not depend on frequency.
Examination Note: Redraw the circuit after replacing each element, so that the examiner can see the equivalent circuit, and then write Z = R1 + R3.
(a) Under which conditions would the rms currents in the two circuits be the same? (b) Can the rms current in circuit (b) be larger than that in (a)?
Answer:
Let (a) have only a resistor: \( I_a = \dfrac{V_{rms}}{R} \). Let (b) be the series R-C-L circuit: \( I_b = \dfrac{V_{rms}}{Z} \), with \( Z = \sqrt{R^2 + (X_L - X_C)^2} \).
(a) The currents are the same when \( Z = R \), i.e. \( (X_L - X_C)^2 = 0 \Rightarrow X_L = X_C \). This is the resonant condition, \( \omega = 1/\sqrt{LC} \).
(b) \( \dfrac{I_a}{I_b} = \dfrac{Z}{R} = \dfrac{\sqrt{R^2 + (X_L - X_C)^2}}{R} \geq 1 \), so \( I_b \leq I_a \). No, the rms current in circuit (b) cannot be larger than that in circuit (a); at best it equals it (at the resonant frequency).
In simple words: Adding L and C to a resistor can only make the impedance larger or equal, so the current can at most stay the same, at the resonant frequency.
Teacher's Note:
1. At the resonant frequency the effects of L and C cancel and the circuit behaves as a pure resistor.
2. Z ≥ R always for a series R-L-C circuit.
Examination Note: State the resonant condition XL = XC for part (a), and use Z ≥ R for part (b).
Question 17. Can the instantaneous power output of an AC source ever be negative? Can the average power output be negative?
Answer:
Let \( e = E_0\sin\omega t \) and \( i = I_0\sin(\omega t + \phi) \). The instantaneous power output is
\[ p = e\,i = E_0 I_0 \sin\omega t\,\sin(\omega t + \phi) = \dfrac{E_0 I_0}{2}\left[\cos\phi - \cos(2\omega t + \phi)\right] \]
When \( \cos(2\omega t + \phi) > \cos\phi \), p is negative. So yes, the instantaneous power can be negative.
The average over a cycle is \( P_{av} = \dfrac{E_0 I_0}{2}\cos\phi = E_{rms}I_{rms}\cos\phi \). For a passive circuit \( \cos\phi = \dfrac{R}{Z} \geq 0 \), so no, the average power output cannot be negative.
In simple words: The source may get some energy back during part of a cycle, but over a full cycle the energy given out is never less than the energy taken back.
Teacher's Note:
1. For a pure inductor or capacitor, the positive and negative parts of the power curve are equal: the average is zero.
2. For a resistor, p = i²R is never negative.
Examination Note: Derive p = (E0I0/2)[cos φ − cos(2ωt + φ)] and use R/Z ≥ 0 for the average; one line of explanation for each answer.
Answer:
Bandwidth is the range of angular frequencies \( \Delta\omega = \omega_2 - \omega_1 \), where \( \omega_1 \) and \( \omega_2 \) are the frequencies at which the current amplitude falls to \( \dfrac{1}{\sqrt{2}} \) of its maximum value.
Maximum current: \( I_{max} = 1.0\ \text{A} \) (at ω = 1.0 rad/s). So \( \dfrac{I_{max}}{\sqrt{2}} = 0.707 \approx 0.7\ \text{A} \).
Reading the graph at I = 0.7 A (the dashed lines in the figure below), the two frequencies are ω1 = 0.8 rad/s and ω2 = 1.2 rad/s.
Bandwidth Δω = 1.2 − 0.8 = 0.4 rad/s
In simple words: The width of the response curve at 0.7 of the peak height is 0.4 rad/s.
Teacher's Note:
1. A narrow bandwidth means a sharp resonant peak (high Q): Q = ω0/Δω = 1.0/0.4 = 2.5 here.
2. The 1/√2 level corresponds to half the maximum power.
Examination Note: Mark the 0.7 A level on the graph, drop perpendiculars to the ω-axis and write the bandwidth; marking on the figure is part of the answer.
Answer:
The current is +1 A for half a period and −2 A for the other half period. The rms value is the square root of the mean of the squares of the current over a cycle:
\[ I_{rms} = \sqrt{\dfrac{1^2\times\frac{T}{2} + (-2)^2\times\frac{T}{2}}{T}} = \sqrt{\dfrac{1 + 4}{2}} = \sqrt{2.5} \approx 1.58\ \text{A} \]
Irms ≈ 1.6 A, shown by the dashed line in the graph below.
In simple words: Square the current, average it over a cycle and take the square root; the negative sign does not matter.
Teacher's Note:
1. For a square wave of equal half-cycles, the mean square is the average of the squares of the two levels.
2. The mean (average) current is (1 − 2)/2 = −0.5 A, quite different from the rms value.
Examination Note: Show the three steps (square, mean, root) and mark the value on the graph. State the result as 1.6 A.
Question 20. How does the sign of the phase angle φ, by which the supply voltage leads the current in an L-C-R series circuit, change as the supply frequency is gradually increased from very low to very high values?
Answer:
\( \tan\phi = \dfrac{X_L - X_C}{R} = \dfrac{2\pi\nu L - \dfrac{1}{2\pi\nu C}}{R} \), where φ is the angle by which voltage leads the current.
At very low frequency \( X_C > X_L \): \( \tan\phi < 0 \), so φ is negative (the circuit is capacitive and the voltage lags the current).
At the resonant frequency \( \nu_0 = \dfrac{1}{2\pi\sqrt{LC}} \): \( X_L = X_C \), \( \tan\phi = 0 \) and φ = 0 (voltage and current in phase).
At higher frequencies \( X_L > X_C \): \( \tan\phi > 0 \), so φ is positive (inductive; the voltage leads the current).
So φ changes from negative to zero at the resonant frequency and then to positive as the frequency increases.
In simple words: Below the resonant frequency the circuit is capacitive (φ negative), at the resonant frequency it is purely resistive (φ = 0), and above the resonant frequency it is inductive (φ positive).
Teacher's Note:
1. φ tends to −90° at very low and +90° at very high frequencies.
2. The sign of φ tells you whether the circuit behaves like a capacitor or like an inductor.
Examination Note: Give the formula for tan φ and the three cases in order of increasing frequency; take care to use ν0 = 1/(2π√(LC)) (not √(2C)).
Short Answer Type Questions
(a) Which curve shows power consumption over a full cycle? (b) What is the average power consumption over a cycle? (c) Identify the device X.
Answer:
(a) Instantaneous power is \( P = vi \), the product of the voltage and current curves. The curve of the product has the largest amplitude and twice the frequency of the others, with equal positive and negative loops. This is curve A.
(b) In one complete cycle the curve has one positive loop and one negative loop of exactly the same area, so the net area is zero. The average power consumption over a cycle is zero.
(c) The voltage curve and the current curve (B and C) are 90° out of phase, so \( \cos\phi = 0 \) and no average power is used. The device must be a pure inductor or a pure capacitor (or an L-C combination with no resistance).
In simple words: If the device takes in as much energy as it returns, its average power is zero; only an ideal inductor or capacitor behaves like this.
Teacher's Note:
1. P = VI is positive when V and I have the same sign and negative when they have opposite signs.
2. In a resistor P is always positive; in an L or C it goes positive and negative equally.
Examination Note: Identify the power curve using frequency doubling and larger amplitude; conclude with 'purely reactive device, average power zero'.
Question 22. Both alternating current and direct current are measured in amperes. But how is the ampere defined for an alternating current?
Answer:
The ampere for a direct current is defined through the magnetic force between two parallel current-carrying wires (or as one coulomb of charge per second).
For an alternating current this force alternates in direction and averages to zero over a cycle, so the definition cannot be used directly. We need a property which does not depend on the direction of the current.
The heating effect is such a property: it depends on \( i^2 \). The ampere for AC is therefore defined through it: an AC of 1 A (rms) is the current which produces the same heating effect in a resistor as a steady (DC) current of 1 A. Mathematically \( I_{rms} = \sqrt{\langle i^2 \rangle} = \dfrac{I_0}{\sqrt{2}} \).
In simple words: An AC ampere is the amount of alternating current that heats a resistor as much as one ampere of DC does.
Teacher's Note:
1. Joule heating ∝ i², so it is independent of the direction of current.
2. The 220 V of the mains is the rms value defined in the same way.
Examination Note: Explain why the DC definition fails and then give the heating-effect definition with Irms = I0/√2.
Question 23. A coil of 0.01 H inductance and 1 Ω resistance is connected to 200 V, 50 Hz AC supply. Find the impedance of the circuit and the time lag between maximum alternating voltage and current.
Answer:
Inductive reactance: \( X_L = 2\pi\nu L = 2\pi\times50\times0.01 = 3.14\ \Omega \).
Impedance: \( Z = \sqrt{R^2 + X_L^2} = \sqrt{1 + 9.87} = \sqrt{10.87} \approx 3.3\ \Omega \).
Phase angle: \( \tan\phi = \dfrac{X_L}{R} = 3.14 \Rightarrow \phi = 72.3^\circ \approx 72^\circ \) (current lags the voltage). In radians, \( \phi = 1.26 \) rad.
Time lag: \( \Delta t = \dfrac{\phi}{\omega} = \dfrac{72.3/360}{50}\ \text{s} \approx 4\times10^{-3}\ \text{s} = \dfrac{1}{250}\ \text{s} \).
In simple words: The coil opposes the AC with 3.3 Ω, and its current peaks about 4 ms after the voltage peak.
Teacher's Note:
1. Time lag = (φ/360°) × T, where T = 1/50 s = 20 ms.
2. The supply voltage (200 V) is not needed for the impedance and the time lag.
Examination Note: Write XL, Z, tan φ and Δt in this order. Convert the angle to time with Δt = φ/ω or (φ/360°)T.
Question 24. A 60 W load is connected to the secondary of a transformer whose primary draws line voltage. If a current of 0.54 A flows in the load, what is the current in the primary coil? Comment on the type of transformer being used.
Answer:
Voltage across the load (secondary): \( V_s = \dfrac{P}{I_s} = \dfrac{60}{0.54} \approx 111\ \text{V} \) (about 110 V).
The primary draws the line voltage, taken as Vp = 220 V.
For an ideal transformer, input power = output power: \( V_pI_p = V_sI_s = 60\ \text{W} \), so \( I_p = \dfrac{60}{220} \approx 0.27\ \text{A} \).
Since \( V_s < V_p \) (about 110 V against 220 V) and \( I_s > I_p \), the transformer is a step-down transformer with a turns ratio of about 1 : 2.
In simple words: A 220 V to 110 V transformer halves the voltage and so doubles the current: the primary current is half of 0.54 A.
Teacher's Note:
1. In a step-down transformer the secondary has fewer turns, a lower voltage and a larger current.
2. An ideal transformer has no loss, so power in equals power out.
Examination Note: State the assumption (ideal transformer, line voltage 220 V) and use VpIp = VsIs.
Question 25. Explain why the reactance provided by a capacitor to an alternating current decreases with increasing frequency.
Answer:
A capacitor does not allow a steady (direct) current to pass, as the gap between its plates is an insulator. When an alternating voltage is applied, the plates are alternately charged and discharged, and this changing charge constitutes the current.
If the voltage changes faster (a higher frequency), a given amount of charge flows on and off the plates in a shorter time, so the current is larger for the same voltage amplitude. The capacitor therefore opposes the current less.
Mathematically \( X_C = \dfrac{1}{\omega C} = \dfrac{1}{2\pi\nu C} \), which falls as ν rises.
In simple words: A faster-changing voltage moves charge on and off the plates more quickly, so a larger current flows; the opposition is smaller.
Teacher's Note:
1. At ν = 0 (DC), XC is infinite: no current. At very high ν, XC is almost zero.
2. Current in a capacitor is I = C dV/dt, so it is proportional to the rate of change of the voltage.
Examination Note: Give the physical idea (rate of change of charge) and then the formula XC = 1/(2πνC).
Question 26. Explain why the reactance offered by an inductor increases with increasing frequency of an alternating voltage.
Answer:
An inductor opposes any change of current by producing a back emf (Lenz's law). If the current is increasing, the back emf opposes the increase; if the current is decreasing, it opposes the decrease.
The back emf is \( \varepsilon = -L\dfrac{di}{dt} \), proportional to the rate of change of current. At a higher frequency the current changes faster, so the back emf and therefore the opposition to the current are larger.
Mathematically \( X_L = \omega L = 2\pi\nu L \), which increases directly with the frequency.
In simple words: The faster the current tries to change, the bigger the back emf the inductor produces, so its opposition grows with frequency.
Teacher's Note:
1. For DC (ν = 0) the reactance is zero: an ideal inductor is just a wire.
2. The reactance of L and C change in opposite ways with frequency.
Examination Note: Explain with Lenz's law and the formula ε = −L di/dt, and finish with XL = 2πνL.
Long Answer Type Questions
Question 27. An electrical device draws 2 kW power from AC mains (voltage 223 V (rms) = \( \sqrt{50000} \) V). The current differs (lags) in phase by φ \( \left(\tan\phi = \dfrac{-3}{4}\right) \) as compared to voltage. Find (a) R, (b) XC − XL and (c) IM. Another device has twice the values for R, XC and XL. How are the answers affected?
Answer:
Given \( P = 2000\ \text{W},\ V_{rms} = \sqrt{50000}\ \text{V} \) and \( \tan\phi = -\dfrac{3}{4} \), so \( |\cos\phi| = \dfrac{4}{5} \) and \( |\sin\phi| = \dfrac{3}{5} \).
Average power: \( P = V_{rms}I_{rms}\cos\phi \Rightarrow I_{rms} = \dfrac{2000}{\sqrt{50000}\times 0.8} = \dfrac{2000}{178.9} \approx 11.18\ \text{A} \).
Impedance: \( Z = \dfrac{V_{rms}}{I_{rms}} = \dfrac{223.6}{11.18} = 20\ \Omega \).
(a) \( R = Z\cos\phi = 20\times0.8 = 16\ \Omega \).
(b) \( \tan\phi = \dfrac{X_L - X_C}{R} = -\dfrac{3}{4} \Rightarrow X_C - X_L = \dfrac{3}{4}\times16 = 12\ \Omega \) (check: \( 16^2 + 12^2 = 20^2 \)).
(c) \( I_M = \sqrt{2}\,I_{rms} = \sqrt{2}\times11.18 \approx 15.8\ \text{A} \) (= \( \sqrt{250} \) A).
Second device: R, XC and XL are doubled, so Z becomes 40 Ω while tan φ is unchanged. The current is halved: \( I_{rms} \approx 5.6\ \text{A} \), \( I_M \approx 7.9\ \text{A} \), and the power becomes \( I^2R = \dfrac{P}{2} = 1\ \text{kW} \) (new R = 32 Ω, XC − XL = 24 Ω).
In simple words: The 2 kW and the power factor 0.8 fix the current; doubling all the resistances and reactances halves the current and halves the power, but leaves the phase angle unchanged.
Teacher's Note:
1. Use P = VI cos φ, not P = V²/Z: the power factor must be included.
2. Doubling Z with the same voltage halves the current, so P = I²R drops to one half.
Examination Note: Find Irms from P = V I cos φ, then Z = V/I, then resolve Z into R and the net reactance. Quote the extra statement for the second device (current and power halved, φ unchanged).
Question 28. 1 MW power is to be delivered from a power station to a town 10 km away. One uses a pair of Cu wires of radius 0.5 cm for this purpose. Calculate the fraction of ohmic losses to power transmitted if (i) power is transmitted at 220 V. Comment on the feasibility of doing this. (ii) a step-up transformer is used to boost the voltage to 11000 V, power transmitted, then a step-down transformer is used to bring voltage to 220 V. (ρCu = 1.7 × 10−8 SI unit)
Answer:
A pair of wires to the town 10 km away has a total length \( l = 20\ \text{km} = 2\times10^4\ \text{m} \). Resistance: \( R = \rho\dfrac{l}{A} = \dfrac{1.7\times10^{-8}\times2\times10^4}{\pi(0.5\times10^{-2})^2} = \dfrac{3.4\times10^{-4}}{7.85\times10^{-5}} \approx 4.3\ \Omega \).
(i) At 220 V: \( I = \dfrac{P}{V} = \dfrac{10^6}{220} \approx 4.5\times10^3\ \text{A} \). Loss: \( I^2R = (4545)^2\times4.33 \approx 8.9\times10^{7}\ \text{W} \), which is about 89 times the power to be transmitted (106 W).
The fraction of loss would be about 89 (that is, 8900 %): this is impossible, since the loss cannot exceed the power supplied. (The voltage drop in the wires, IR ≈ 2 × 104 V, is far more than 220 V.) Transmission at 220 V is not feasible.
(ii) At 11000 V: \( I' = \dfrac{10^6}{11000} \approx 90.9\ \text{A} \). Loss: \( I'^2R = (90.9)^2\times4.33 \approx 3.6\times10^{4}\ \text{W} \).
Fraction of loss: \( \dfrac{3.6\times10^4}{10^6} \approx 0.036 \), i.e. about 3.6 %.
In simple words: At 220 V the line would waste far more than the power sent; stepping the voltage up to 11 kV cuts the current 50 times and the loss 2500 times, so only about 3.6 % is lost.
Teacher's Note:
1. Loss ∝ I² ∝ 1/V²: raising the voltage 50 times reduces the loss 2500 times.
2. Remember the wires go to the town and back, so the length is 2 × 10 km.
Examination Note: Use the total length 20 km, show R, I and I²R, and comment clearly that the 220 V option is not feasible because the loss exceeds the power sent.
Answer:
Let i1 be the current through R and i2 the current through the series C-L branch; the total current is \( i = i_1 + i_2 \). Both branches have the same voltage \( V_m\sin\omega t \) across them.
R branch: \( i_1 = \dfrac{V_m\sin\omega t}{R} \).
C-L branch: with q the charge on the capacitor, KVL gives \( \dfrac{q}{C} + L\dfrac{di_2}{dt} = V_m\sin\omega t \), i.e. \( L\dfrac{d^2q}{dt^2} + \dfrac{q}{C} = V_m\sin\omega t \).
Try \( q = q_m\sin\omega t \). Then \( q_m\left(\dfrac{1}{C} - L\omega^2\right) = V_m \), so \( q_m = \dfrac{V_m}{\frac{1}{C} - L\omega^2} \).
\( i_2 = \dfrac{dq}{dt} = \omega q_m\cos\omega t = \dfrac{V_m\cos\omega t}{\frac{1}{\omega C} - \omega L} \). This is 90° out of phase with i1.
Net current: \( i = V_m\left[\dfrac{\sin\omega t}{R} + \dfrac{\cos\omega t}{X_C - X_L}\right] \), with \( X_C = \dfrac{1}{\omega C},\ X_L = \omega L \).
Write this as \( i = i_m\sin(\omega t + \phi) \) with \( i_m\cos\phi = \dfrac{V_m}{R} \) and \( i_m\sin\phi = \dfrac{V_m}{X_C - X_L} \). Then \( i_m = V_m\sqrt{\dfrac{1}{R^2} + \dfrac{1}{(X_C - X_L)^2}} \) and the phase of i is \( \phi = \tan^{-1}\dfrac{R}{X_C - X_L} \) (with respect to the applied voltage).
Comparing with \( i_m = \dfrac{V_m}{Z} \): \( \dfrac{1}{Z} = \sqrt{\dfrac{1}{R^2} + \dfrac{1}{\left(\frac{1}{\omega C} - \omega L\right)^2}} \). This is the impedance of the circuit; it is not the series formula, because here the branches are in parallel.
In simple words: The total current is the sum of two currents 90° apart, one through R and one through the L-C branch, and the impedance is found from the Pythagoras-like combination of their amplitudes.
Teacher's Note:
1. Parallel branches: add currents, not impedances. The formula for the series L-C-R circuit must not be used here.
2. At ω = 1/√(LC), the L-C branch has zero impedance (XC = XL), so the total impedance Z = 0 and the current is very large.
Examination Note: Write KVL for the L-C branch, solve for q, find i2, add the two currents using the phasor (Pythagoras) method and read off 1/Z.
(a) Multiply the equation by i and simplify where possible. (b) Interpret each term physically. (c) Cast the equation in the form of a conservation of energy statement. (d) Integrate the equation over one cycle to find that the phase difference between V and i must be acute.
Answer:
KVL for the series L-C-R circuit: \( L\dfrac{di}{dt} + Ri + \dfrac{q}{C} = V_m\sin\omega t = V_i \).
(a) Multiply by i: \( Li\dfrac{di}{dt} + i^2R + \dfrac{q}{C}i = V_i\,i \). Using \( i = \dfrac{dq}{dt} \): \( Li\dfrac{di}{dt} = \dfrac{d}{dt}\left(\dfrac{1}{2}Li^2\right) \) and \( \dfrac{q}{C}\dfrac{dq}{dt} = \dfrac{d}{dt}\left(\dfrac{q^2}{2C}\right) \). So \( \dfrac{d}{dt}\left(\dfrac{1}{2}Li^2 + \dfrac{q^2}{2C}\right) + i^2R = V_i\,i \).
(b) \( \dfrac{d}{dt}\left(\dfrac{1}{2}Li^2\right) \) is the rate of change of the energy stored in the inductor; \( \dfrac{d}{dt}\left(\dfrac{q^2}{2C}\right) \) is the rate of change of the energy stored in the capacitor; \( i^2R \) is the rate of Joule heating in the resistor; \( V_i\,i \) is the power supplied by the source.
(c) Energy conservation: power supplied by the source = rate of increase of the energy stored in L and C + rate of heat loss in R.
(d) Integrate over one full cycle (0 to T): \( \left[\dfrac{1}{2}Li^2 + \dfrac{q^2}{2C}\right]_0^T + \int_0^T i^2R\,dt = \int_0^T V_i\,i\,dt \). The stored energy is the same at t = 0 and at t = T, so the first term is zero. The Joule loss is positive, so \( \int_0^T V_i\,i\,dt = \int_0^T i^2R\,dt > 0 \).
With \( i = i_m\sin(\omega t + \phi) \): \( \int_0^T V_i\,i\,dt = \dfrac{V_m i_m T}{2}\cos\phi \). It is positive only if \( \cos\phi > 0 \), i.e. the phase difference φ between V and i must be acute (|φ| < 90°).
In simple words: Over a full cycle the source must supply the energy lost as heat in the resistor, which is positive, so cos φ must be positive and φ acute.
Teacher's Note:
1. The stored energies in L and C go back and forth and return to their starting value after a full cycle, so they cannot make a net contribution.
2. The relation cos φ = R/Z ≥ 0 gives the same conclusion.
Examination Note: Present the steps with the labels (a) to (d). In (d), say clearly that the stored energy returns to its initial value after a period.
(a) Write down the equation of motion for q(t). (b) At t = t0, the voltage source stops and R is short circuited. Now write down how much energy is stored in each of L and C. (c) Describe subsequent motion of charges.
Answer:
(a) KVL: \( iR + L\dfrac{di}{dt} + \dfrac{q}{C} = V_m\sin\omega t \). With \( i = \dfrac{dq}{dt} \):
\[ L\dfrac{d^2q}{dt^2} + R\dfrac{dq}{dt} + \dfrac{q}{C} = V_m\sin\omega t \]
(b) Before t0 the circuit is in the steady state: \( i = i_m\sin(\omega t + \phi) \), \( q = -\dfrac{i_m}{\omega}\cos(\omega t + \phi) \), with \( i_m = \dfrac{V_m}{Z} = \dfrac{V_m}{\sqrt{R^2 + (X_C - X_L)^2}} \) and \( \phi = \tan^{-1}\dfrac{X_C - X_L}{R} \).
At t = t0, the energy in the inductor is \( U_L = \dfrac{1}{2}Li^2 = \dfrac{1}{2}L\dfrac{V_m^2}{R^2 + (X_C - X_L)^2}\sin^2(\omega t_0 + \phi) \).
The energy in the capacitor is \( U_C = \dfrac{q^2}{2C} = \dfrac{1}{2C\omega^2}\dfrac{V_m^2}{R^2 + (X_C - X_L)^2}\cos^2(\omega t_0 + \phi) \).
(c) After t0 the source is off and R is short-circuited, so the circuit is a pure L-C oscillator. The energy UL + UC stays constant (no resistor to dissipate it). The charges oscillate back and forth between the capacitor and the inductor with angular frequency \( \omega_0 = \dfrac{1}{\sqrt{LC}} \), and the energy changes continuously between electric energy (capacitor) and magnetic energy (inductor), with no damping.
In simple words: Once R is shorted and the source removed, the stored energy just sloshes back and forth between L and C at the natural frequency 1/√(LC).
Teacher's Note:
1. The equation in (a) is the electrical equivalent of a driven damped spring-block system: L ↔ m, R ↔ damping, 1/C ↔ k.
2. Energy stored in an L-C pair is constant when no resistance is present.
Examination Note: Quote the steady-state i and q at t0 to get UL and UC, then describe the L-C oscillations in (c) using the words 'undamped' and 'natural frequency'.