These NCERT Exemplar solutions for Class 12 Physics Chapter 15, Communication Systems, give step-by-step answers to all 30 questions: 9 MCQs, 5 multiple-correct MCQs, 6 very short, 5 short and 5 long answer questions. They cover propagation of ground, sky and space waves, antenna length and line-of-sight range, decibel calculations, amplitude modulation and its spectrum, demodulation with a diode detector and the noise advantage of FM. Each answer is followed by a short Teacher's Note to build understanding and an Examination Note on how to present the answer for better marks. This chapter has been removed from the current CBSE syllabus but is retained here for completeness.
Multiple Choice Questions (MCQs)
(a) A is transmitted via space wave while B and C are transmitted via sky wave
(b) A is transmitted via ground wave, B via sky wave and C via space wave
(c) B and C are transmitted via ground wave while A is transmitted via sky wave
(d) B is transmitted via ground wave while A and C are transmitted via space wave
Show Answer & Explanation
Answer: (b) A is transmitted via ground wave, B via sky wave and C via space wave
Explanation:
1. Ground wave propagation is used for about 530 kHz to 1710 kHz, sky wave propagation for about 1710 kHz to 40 MHz, and space wave propagation for about 54 MHz to 42 GHz.
2. A (1600 kHz) falls in the ground-wave range, B (5 MHz) in the sky-wave range and C (60 MHz) in the space-wave range. Hence option (b).
Teacher's Note:
1. Low frequencies follow the ground, medium-high frequencies are reflected by the ionosphere, and very high frequencies need a straight line of sight.
2. Remember the three ranges in order of increasing frequency: ground, sky, space.
Examination Note: Place each frequency in its range first and then pick the option; quote the ranges to show how you decided.
(a) ~ 400 m
(b) ~ 25 m
(c) ~ 150 m
(d) ~ 2400 m
Show Answer & Explanation
Answer: (d) ~ 2400 m
Explanation:
1. An efficient transmitting antenna has a length of about a quarter of the wavelength: \( l \approx \dfrac{\lambda}{4} \).
2. The antenna stands on the building, so the total height of the complex is \( l = 500 + 100 = 600\ \text{m} \).
3. \( \lambda \approx 4l = 4\times600 = 2400\ \text{m} \).
Teacher's Note:
1. The building and the antenna together make the tower, so add the two heights.
2. A quarter-wavelength antenna radiates efficiently; very short antennas radiate poorly.
Examination Note: Add the heights first, then use l = λ/4. Using only the 100 m antenna is the common mistake.
(a) 900 W
(b) 100 W
(c) 990 W
(d) 1010 W
Show Answer & Explanation
Answer: (b) 100 W
Explanation:
1. Total gain over 5 km: \( 5\times(-2) = -10\ \text{dB} \).
2. \( -10 = 10\log_{10}\dfrac{P_0}{P_i} \Rightarrow \dfrac{P_0}{P_i} = 10^{-1} \).
3. \( P_0 = \dfrac{1000}{10} = 100\ \text{W} \).
Teacher's Note:
1. −10 dB means the power is reduced to one-tenth; −20 dB would be one-hundredth.
2. Decibels add along the path, but powers multiply.
Examination Note: Add the decibels, then convert back with the antilog.
(a) 1.003 MHz and 0.997 MHz
(b) 3001 kHz and 2997 kHz
(c) 1003 kHz and 1000 kHz
(d) 1 MHz and 0.997 MHz
Show Answer & Explanation
Answer: (a) 1.003 MHz and 0.997 MHz
Explanation:
1. Side band frequencies are \( f_c \pm f_m \).
2. 3 kHz = 0.003 MHz, so the side bands are \( 1 \pm 0.003 \), that is 1.003 MHz and 0.997 MHz.
Teacher's Note:
1. The upper side band is fc + fm and the lower is fc − fm.
2. The bandwidth is 2fm = 6 kHz.
Examination Note: Convert kHz and MHz to the same unit before adding and subtracting.
(a) ωm
(b) ωc
(c) \( \dfrac{\omega_c+\omega_m}{2} \)
(d) \( \dfrac{\omega_c-\omega_m}{2} \)
Show Answer & Explanation
Answer: (b) ωc
Explanation:
1. In amplitude modulation only the amplitude of the carrier changes with the message; the oscillation inside the envelope remains at the carrier frequency.
2. So the AM wave has the frequency \( \omega_c \) (the side bands \( \omega_c\pm\omega_m \) are extra components that together make the changing amplitude).
Teacher's Note:
1. The envelope follows the message but the rapid oscillations are those of the carrier.
2. In frequency modulation it is the frequency, not the amplitude, that changes.
Examination Note: State that the carrier frequency is unchanged and only the amplitude varies.
(a) (i) and (iii)
(b) only (iii)
(c) (ii) and some regions of (iv)
(d) All the devices can be used
Show Answer & Explanation
Answer: (c) (ii) and some regions of (iv)
Explanation:
1. Modulation needs a non-linear device, because a linear device (output proportional to input) cannot produce the product terms that give the side bands.
2. (i) is a straight line and (iii) is constant current, so they are not suitable. (ii) is curved (non-linear, like a square-law device) and (iv) is non-linear in some regions. Hence option (c).
Teacher's Note:
1. A linear device gives out only the frequencies put in; a non-linear one produces sums and differences.
2. A diode or a transistor in its curved region is the usual modulating device.
Examination Note: Say that a non-linear I-V relation is the requirement and point out the curved graphs.
(a) poor selection of modulation index (selected 0 < m < 1)
(b) poor bandwidth selection of amplifiers
(c) poor selection of carrier frequency
(d) loss of energy in transmission.
Show Answer & Explanation
Answer: (b) poor bandwidth selection of amplifiers
Explanation:
1. A female voice has higher frequencies than a male voice. If the amplifiers pass only the higher part of the band (poor bandwidth selection), the low-frequency components are lost and the received voice sounds higher in pitch.
2. The modulation index (0 < m < 1 is the correct range), the choice of carrier frequency and the loss of energy do not change the pitch in this way.
Teacher's Note:
1. The pitch of a voice depends on the frequencies present; remove the low ones and it sounds higher.
2. The amplifier band must cover the whole range of the signal.
Examination Note: Connect the pitch to the frequency content and say the amplifier cuts off the low frequencies.
(a) ABCDE
(b) BADEC
(c) BDACE
(d) BEADC
Show Answer & Explanation
Answer: (b) BADEC
Explanation:
1. The message starts at the information source (B), is processed and sent by the transmitter (A), travels through the channel (D), is picked up by the receiver (E) and finally reaches the user of the information (C).
2. The sequence is therefore B, A, D, E, C: information source → transmitter → channel → receiver → user (with noise added in the channel).
Teacher's Note:
1. Follow the path of a message from the speaker to the listener.
2. Noise enters in the channel, not in the transmitter or the receiver.
Examination Note: Write the sequence with arrows to show the order.
(a) \( A_c\sin\{[\omega_c + k_1V_m(t)]t+\phi\} \)
(b) \( A_c\sin\{\omega_ct + \phi + k_2V_m(t)\} \)
(c) \( \{A_c + k_2V_m(t)\}\sin(\omega_ct+\phi) \)
(d) \( A_cV_m(t)\sin(\omega_ct+\phi) \)
Show Answer & Explanation
Answer: (c) \( \{A_c + k_2V_m(t)\}\sin(\omega_ct+\phi) \)
Explanation:
1. In AM the amplitude of the carrier \( A_c\sin(\omega_ct+\phi) \) is made to vary in proportion to the message \( V_m(t) \): the new amplitude is \( A_c + k_2V_m(t) \).
2. So the AM wave is \( \{A_c + k_2V_m(t)\}\sin(\omega_ct+\phi) \). Option (a) varies the frequency and (b) the phase of the carrier, and (d) is a product with no carrier amplitude term.
Teacher's Note:
1. Compare which quantity of the carrier (amplitude, frequency, phase) contains the message.
2. (a) is frequency modulation and (b) is phase modulation.
Examination Note: Identify the quantity that carries the message; in AM it is the amplitude.
Multiple Choice Questions (More Than One Options)
(a) the size of the required antenna would be at least 5 km which is not convenient
(b) the audio signal can not be transmitted through sky waves
(c) the size of the required antenna would be at least 20 km, which is not convenient
(d) effective power transmitted would be very low, if the size of the antenna is less than 5 km
Show Answer & Explanation
Answer: (a) the size of the required antenna would be at least 5 km which is not convenient, (b) the audio signal can not be transmitted through sky waves, (d) effective power transmitted would be very low, if the size of the antenna is less than 5 km
Explanation:
1. Wavelength: \( \lambda = \dfrac{c}{\nu} = \dfrac{3\times10^{8}}{15\times10^{3}} = 20\ \text{km} \). The antenna must be about \( \lambda/4 = 5\ \text{km} \) long. So (a) is correct and (c) is wrong (20 km is the wavelength, not the antenna length).
2. Audio frequencies are absorbed by the atmosphere and are not reflected by the ionosphere, so they cannot be sent as sky waves. (b) is correct.
3. An antenna shorter than about 5 km radiates very little power at this wavelength. (d) is correct.
Teacher's Note:
1. Antenna length should be comparable with the wavelength (about λ/4).
2. Modulation moves the signal to a high carrier frequency, so a short antenna will do.
Examination Note: Calculate λ and then λ/4; this settles (a) and (c).
(a) The side band frequencies are 1506 kHz and 1494 kHz
(b) The bandwidth required for amplitude modulation is 6 kHz
(c) The bandwidth required for amplitude modulation is 3 MHz
(d) The side band frequencies are 1503 kHz and 1497 kHz
Show Answer & Explanation
Answer: (b) The bandwidth required for amplitude modulation is 6 kHz, (d) The side band frequencies are 1503 kHz and 1497 kHz
Explanation:
1. Carrier = 1.5 MHz = 1500 kHz. The side bands are \( 1500 \pm 3 \), that is 1503 kHz and 1497 kHz. (d) is correct and (a) is wrong.
2. Bandwidth = \( 2f_m = 2\times3 = 6\ \text{kHz} \). (b) is correct and (c) is wrong.
Teacher's Note:
1. Bandwidth of AM is twice the highest message frequency, not related to the carrier frequency.
2. Always convert MHz into kHz first.
Examination Note: Show the side bands and the bandwidth as two separate lines.
(a) 100 km
(b) 24 km
(c) 55 km
(d) 50 km
Show Answer & Explanation
Answer: (b) 24 km, (c) 55 km, (d) 50 km
Explanation:
1. The maximum range for line-of-sight communication is \( d = \sqrt{2Rh} = \sqrt{2\times6.4\times10^{6}\times240} \approx 5.5\times10^{4}\ \text{m} = 55.4\ \text{km} \).
2. Signals can be received at any distance up to 55.4 km, so 24 km, 55 km and 50 km are all possible. 100 km is beyond the range.
Teacher's Note:
1. Range is the maximum distance; places nearer than this are also covered.
2. The range increases with the square root of the height of the tower.
Examination Note: Calculate the range and say that all smaller distances are covered.
(a) (i) followed by (ii)
(b) (ii) followed by (i)
(c) (iii)
(d) (iv)
Show Answer & Explanation
Answer: (a) (i) followed by (ii), (b) (ii) followed by (i), (c) (iii)
Explanation:
1. An AM wave must contain only frequencies between \( \omega_c - \omega_m \) and \( \omega_c + \omega_m \) (the carrier and the two side bands), so the filter must pass this band and reject the rest: a band-pass response.
2. Curve (iii) is exactly a band-pass filter, so (c) is correct.
3. A low-pass filter (i, cut-off at \( \omega_c+\omega_m \)) and a high-pass filter (ii, cut-off at \( \omega_c-\omega_m \)) in series, in either order, also pass only the band between them. So (a) and (b) are correct.
4. Curve (iv) rejects the required band, so it is wrong.
Teacher's Note:
1. A band-pass filter is a low-pass and a high-pass filter in series.
2. Order of the two filters does not matter for the final band.
Examination Note: Name the band required and show how each correct option gives it.
(a) m > 1, will result in interference between carrier frequency and message frequency, resulting into distortion
(b) m > 1, will result in overlapping of both side bands resulting into loss of information
(c) m > 1, will result in change in phase between carrier signal and message signal
(d) m > 1, indicates amplitude of message signal greater than amplitude of carrier signal resulting into distortion
Show Answer & Explanation
Answer: (b) m > 1, will result in overlapping of both side bands resulting into loss of information, (d) m > 1, indicates amplitude of message signal greater than amplitude of carrier signal resulting into distortion
Explanation:
1. The modulation index is \( m = \dfrac{A_m}{A_c} \). If \( m > 1 \), the amplitude of the message is greater than the amplitude of the carrier, so the envelope of the AM wave no longer follows the message. This is over-modulation, and the signal is distorted. (d) is correct.
2. The distorted envelope contains extra frequency components that spread into the side-band region, and the information of the message is lost. This is what option (b) says. (a) and (c) do not describe the cause.
Teacher's Note:
1. For m ≤ 1 the envelope is a faithful copy of the message.
2. Over-modulation is like clipping a recording that is too loud.
Examination Note: Define m = Am/Ac, state that m > 1 gives distortion and loss of information.
Very Short Answer Type Questions
Question 15. Which of the following would produce analog signals and which would produce digital signals? (a) A vibrating tuning fork (b) Musical sound due to a vibrating sitar string (c) Light pulse (d) Output of NAND gate
Answer:
An analog signal varies continuously in time and can take any value in a range. A digital signal has only two distinct levels (0 and 1).
(a) A vibrating tuning fork gives a continuously varying sinusoidal signal: analog.
(b) The sound of a sitar string varies continuously: analog.
(c) A light pulse is either on or off: digital.
(d) The output of a NAND gate is either high or low (1 or 0): digital.
In simple words: Smoothly varying signals are analog, and signals with only on and off levels are digital.
Teacher's Note:
1. Digital signals are the basis of computers because two levels are easy to produce and reliable to detect.
2. Sound produced by vibrating objects is analog.
Examination Note: Give a one-line definition of each type and place each of the four items in one of them.
Question 16. Would sky waves be suitable for transmission of TV signals of 60 MHz frequency?
Answer:
Sky wave propagation depends on reflection by the ionosphere, which reflects waves only up to a frequency of about 40 MHz.
A 60 MHz signal is above this limit and passes through the ionosphere instead of being reflected back.
So sky waves are not suitable for 60 MHz TV signals; such signals are sent by space waves (line-of-sight) or by satellites.
In simple words: Waves above about 40 MHz go through the ionosphere instead of bouncing back, so TV signals cannot travel as sky waves.
Teacher's Note:
1. The ionosphere can reflect only waves below a critical frequency set by its electron density.
2. This is why TV towers and satellites are used for TV broadcasting.
Examination Note: Give the sky-wave frequency limit (about 40 MHz) and compare it with 60 MHz.
Question 17. Two waves A and B of frequencies 2 MHz and 3 MHz, respectively are beamed in the same direction for communication via sky wave. Which one of these is likely to travel longer distance in the ionosphere before suffering total internal reflection?
Answer:
The refractive index of the ionosphere increases with the frequency of the wave (it approaches 1 for high frequencies), so wave B (3 MHz) sees a higher refractive index than wave A (2 MHz).
A wave bends less at each layer when the refractive index change is small, so the wave of higher frequency bends more gradually and has to go deeper into the ionosphere before the angle of incidence reaches the critical angle.
Hence wave B (3 MHz) travels the longer distance in the ionosphere before total internal reflection.
In simple words: The higher the frequency, the less the wave is bent by the ionosphere, so it goes farther in before it is turned back.
Teacher's Note:
1. Total internal reflection occurs when the angle of incidence exceeds the critical angle at a layer.
2. Beyond a limiting frequency the wave is not turned back at all.
Examination Note: State the variation of refractive index with frequency and use it to compare the two waves.
Question 18. The maximum amplitude of an AM wave is found to be 15 V while its minimum amplitude is found to be 3 V. What is the modulation index?
Answer:
Let \( A_c \) and \( A_m \) be the amplitudes of the carrier and the message. Then \( A_c + A_m = 15\ \text{V} \) and \( A_c - A_m = 3\ \text{V} \).
Adding: \( 2A_c = 18 \Rightarrow A_c = 9\ \text{V} \). Subtracting: \( 2A_m = 12 \Rightarrow A_m = 6\ \text{V} \).
\( m = \dfrac{A_m}{A_c} = \dfrac{6}{9} = \dfrac23 \)
Modulation index m = 2/3 ≈ 0.67 (67 %)
In simple words: The maximum and minimum of the envelope are the carrier amplitude plus and minus the message amplitude, which gives m = (max − min)/(max + min) = 12/18.
Teacher's Note:
1. The modulation index must not be greater than 1.
2. Direct formula: m = (Amax − Amin)/(Amax + Amin).
Examination Note: Write both equations, solve for Ac and Am and then find m. Give it as a ratio or percentage.
Question 19. Compute the LC product of a tuned amplifier circuit required to generate a carrier wave of 1 MHz for amplitude modulation.
Answer:
For a tuned (LC) circuit the frequency is \( f = \dfrac{1}{2\pi\sqrt{LC}} \).
\( \sqrt{LC} = \dfrac{1}{2\pi f} = \dfrac{1}{2\pi\times10^{6}} \)
\( LC = \dfrac{1}{(2\pi\times10^{6})^{2}} = \dfrac{1}{3.95\times10^{13}} \approx 2.53\times10^{-14}\ \text{s}^{2} \)
LC ≈ 2.53 × 10−14 s² (for example, L = 25.3 μH with C = 1 nF).
In simple words: The product LC fixes the frequency of the oscillator; for 1 MHz it is about 2.5 × 10−14 s².
Teacher's Note:
1. The unit of LC is second squared, because the unit of √(LC) is the second.
2. Many pairs of L and C give the same product.
Examination Note: Square the expression for f and give the answer with the unit s².
Question 20. Why is a AM signal likely to be more noisy than a FM signal upon transmission through a channel?
Answer:
In AM the message is contained in the amplitude of the carrier. Noise added in the channel is also a random change of amplitude, so the receiver cannot tell it from the message and it becomes part of the output.
In FM the message is contained in the frequency of the carrier, and the amplitude carries no information. The FM receiver uses a limiter that removes amplitude variations, so most of the noise is removed.
Hence an AM signal is noisier than an FM signal.
In simple words: Noise changes the height (amplitude) of a wave, which is where AM keeps its message, but not where FM keeps its message.
Teacher's Note:
1. FM needs a larger bandwidth but gives much better quality (less noise).
2. This is why FM radio is clearer than AM radio.
Examination Note: Say what quantity carries the message in each system and what noise changes.
Short Answer Type Questions
Answer:
Loss in the path: \( 2\ \text{dB/km}\times5\ \text{km} = 10\ \text{dB} \) (a gain of −10 dB).
Total gain of the amplifiers: \( 10 + 20 = 30\ \text{dB} \). Overall gain: \( 30 - 10 = 20\ \text{dB} \).
\( 20 = 10\log_{10}\dfrac{P_0}{P_i} \Rightarrow \dfrac{P_0}{P_i} = 10^{2} = 100 \)
\( P_0 = 100\times1.01\ \text{mW} = 101\ \text{mW} \)
Output power = 101 mW
In simple words: Gains and losses in decibels simply add, and +20 dB means the power is multiplied by 100.
Teacher's Note:
1. +10 dB is a factor of 10 in power, +20 dB is a factor of 100.
2. Add all gains in dB first and convert once at the end.
Examination Note: Add the decibels, then convert with the antilog. State the answer in mW.
Question 22. A TV transmission tower antenna is at a height of 20 m. How much service area can it cover if the receiving antenna is (i) at ground level, (ii) at a height of 25 m? Calculate the percentage increase in area covered in case (ii) relative to case (i).
Answer:
Take R = 6.4 × 106 m. The range of an antenna of height h is \( \sqrt{2Rh} \).
(i) \( d_1 = \sqrt{2\times6.4\times10^{6}\times20} = 1.6\times10^{4}\ \text{m} = 16\ \text{km} \). Area \( A_1 = \pi d_1^{2} = 3.14\times16^{2} \approx 804\ \text{km}^{2} \).
(ii) With the receiving antenna at 25 m the range is the sum of the two ranges: \( d_2 = \sqrt{2Rh_T} + \sqrt{2Rh_R} = 16 + \sqrt{2\times6.4\times10^{6}\times25}\ \text{m} = 16 + 17.9 = 33.9\ \text{km} \). Area \( A_2 = 3.14\times33.9^{2} \approx 3609\ \text{km}^{2} \).
Percentage increase: \( \dfrac{A_2 - A_1}{A_1}\times100 = \dfrac{3609 - 804}{804}\times100 \approx 349\ \% \).
Service area ≈ 804 km² (receiver at ground) and ≈ 3609 km² (receiver at 25 m); increase ≈ 349 %
In simple words: Raising the receiving antenna extends the range from 16 km to 33.9 km, so the area covered becomes about four and a half times as large.
Teacher's Note:
1. Maximum LOS distance between two antennas is the sum of √(2Rh) for each.
2. Area goes as the square of the range, so a small gain in range gives a big gain in area.
Examination Note: Calculate the range in each case, then the area with A = πd² and the percentage increase.
Question 23. If the whole earth is to be connected by LOS communication using space waves (no restriction of antenna size or tower height), what is the minimum number of antennas required? Calculate the tower height of these antennas in terms of earth's radius.
Answer:
A tower of height h sees the part of the earth's surface up to the points where its line of sight just touches the earth. If this region subtends an angle θ at the centre of the earth, then \( \cos\theta = \dfrac{R}{R+h} \).
Every point of the earth must be within the region of at least one tower. Fewer than four towers cannot do this with a finite height (two or three towers would need θ = 90°, which means an infinite height).
Four towers placed at the corners of a regular tetrahedron around the earth are the least number that works. The point of the earth farthest from all the towers (the point opposite a tower) is at an angle \( \cos^{-1}\tfrac13 \approx 70.5^\circ \) from the other three. So \( \cos\theta = \dfrac13 \).
\( \dfrac{R}{R+h} = \dfrac13 \Rightarrow h = 2R \)
If the towers are placed at the ends of three mutually perpendicular diameters (six towers), the farthest point is at \( \cos^{-1}(1/\sqrt3) \approx 54.7^\circ \) and the height needed is only \( (\sqrt3 - 1)R \approx 0.73R \); a height of about R (a commonly quoted value for six towers) is more than enough.
Minimum number of antennas = 4, each of height 2R (tetrahedral arrangement)
In simple words: To cover the whole earth with a few towers they must be very tall, of the order of the earth's own radius, which is not practical, and this is why satellites are used for global communication.
Teacher's Note:
1. Earth is a sphere, so the towers have to be spread around it in three dimensions.
2. The relation cos θ = R/(R+h) comes from the right-angled triangle formed by the centre of the earth, the tower and the point where the line of sight touches the earth.
Examination Note: State your arrangement of towers clearly and give the height in terms of R. Stating cos θ = R/(R + h) shows the method.
Question 24. The maximum frequency for reflection of sky waves from a certain layer of the ionosphere is found to be fmax = 9 (Nmax)1/2, where Nmax is the maximum electron density at that layer of the ionosphere. On a certain day it is observed that signals of frequencies higher than 5 MHz are not received by reflection from the F1 layer of the ionosphere while signals of frequencies higher than 8 MHz are not received by reflection from the F2 layer of the ionosphere. Estimate the maximum electron densities of the F1 and F2 layers on that day.
Answer:
From \( f_{max} = 9\sqrt{N_{max}} \): \( N_{max} = \left(\dfrac{f_{max}}{9}\right)^{2} \).
F1 layer: \( f_{max} = 5\ \text{MHz} = 5\times10^{6}\ \text{Hz} \), so \( N_{max} = \left(\dfrac{5\times10^{6}}{9}\right)^{2} = 3.09\times10^{11}\ \text{m}^{-3} \).
F2 layer: \( f_{max} = 8\ \text{MHz} \), so \( N_{max} = \left(\dfrac{8\times10^{6}}{9}\right)^{2} = 7.9\times10^{11}\ \text{m}^{-3} \).
Nmax ≈ 3.1 × 1011 m−3 for F1 and ≈ 7.9 × 1011 m−3 for F2
In simple words: The higher the electron density of a layer, the higher the frequency it can reflect, so the F2 layer (8 MHz) is denser than the F1 layer (5 MHz).
Teacher's Note:
1. Convert MHz to Hz before squaring.
2. The result agrees with the fact that F2 is the layer of highest electron density.
Examination Note: Make N the subject of the formula, substitute in hertz and give the unit m−3.
Question 25. On radiating (sending out) an AM modulated signal, the total radiated power is due to energy carried by ωc, ωc − ωm and ωc + ωm. Suggest ways to minimise cost of radiation without compromising on information.
Answer:
The information is contained only in the side bands \( \omega_c + \omega_m \) and \( \omega_c - \omega_m \). The carrier \( \omega_c \) carries no information, though most of the power is in it.
Moreover, the two side bands carry the same information.
So the cost can be reduced by not transmitting the carrier, and also by transmitting only one side band (single side band transmission, SSB). The receiver can recover the message from one side band, and the power and the bandwidth used are much smaller.
In simple words: Send only what carries the information: one side band is enough, so the carrier and the other side band can be suppressed.
Teacher's Note:
1. Single side band needs half the bandwidth of ordinary AM, so more channels can be fitted in.
2. The receiver has to put back the carrier to recover the message.
Examination Note: Say which component carries the information and which can be left out. Name SSB.
Long Answer Type Questions
Question 26. The intensity of a light pulse travelling along a communication channel decreases exponentially with distance x according to the relation I = I0e−αx, where I0 is the intensity at x = 0 and α is the attenuation constant. (a) Show that the intensity reduces by 75 % after a distance of (ln 4/α). (b) Attenuation of a signal can be expressed in decibel (dB) according to the relation dB = 10 log10(I/I0). What is the attenuation in dB/km for an optical fibre in which the intensity falls by 50 % over a distance of 50 km?
Answer:
(a) A reduction by 75 % leaves 25 % of the intensity: \( I = \dfrac{I_0}{4} \). Then \( \dfrac{I_0}{4} = I_0e^{-\alpha x} \Rightarrow e^{-\alpha x} = \dfrac14 \).
Taking natural logarithms: \( -\alpha x = \ln\dfrac14 = -\ln4 \), so \( x = \dfrac{\ln4}{\alpha} \). Hence the intensity falls by 75 % at \( x = \ln4/\alpha \).
(b) The intensity falls by 50 % over 50 km, so \( \dfrac{I}{I_0} = \dfrac12 \). The attenuation over 50 km is \( 10\log_{10}\dfrac12 = -10\times0.301 = -3.01\ \text{dB} \).
Attenuation per km: \( \dfrac{-3.01}{50} = -0.0602\ \text{dB/km} \).
The attenuation of the fibre is about 0.06 dB/km (the negative sign shows a loss).
In simple words: A loss of half the intensity over 50 km is 3 dB over 50 km, which is about 0.06 dB for each kilometre.
Teacher's Note:
1. Using a different symbol for the dB attenuation avoids confusion with the attenuation constant α of part (a).
2. Losing half the power is about 3 dB; losing 90 % is 10 dB.
Examination Note: In (a) take the natural log of both sides; in (b) find the total decibels and divide by the distance.
Question 27. A 50 MHz sky wave takes 4.04 ms to reach a receiver via re-transmission from a satellite 600 km above Earth's surface. Assuming re-transmission time by satellite negligible, find the distance between source and receiver. If communication between the two was to be done by Line of Sight (LOS) method, what should size and placement of receiving and transmitting antenna be?
Answer:
The signal goes from the source up to the satellite and down to the receiver. Total path \( = 2x = ct = 3\times10^{8}\times4.04\times10^{-3} = 1212\ \text{km} \), so each slant path is \( x = 606\ \text{km} \).
The satellite is 600 km above the midpoint, so by Pythagoras the horizontal distance from source (or receiver) to the point below the satellite is \( d = \sqrt{606^{2} - 600^{2}} = \sqrt{7236} \approx 85.06\ \text{km} \).
Distance between source and receiver = 2d ≈ 170 km.
For line of sight with both antennas at the same height h, each antenna must cover a range \( d = \sqrt{2Rh} \) (so that the two ranges meet at the midpoint). Hence \( h = \dfrac{d^{2}}{2R} = \dfrac{7236}{2\times6400}\ \text{km} = 0.565\ \text{km} \).
Both the transmitting and the receiving antennas should be towers about 565 m high, placed 170 km apart.
In simple words: The ground distance comes from the travel time and a right-angled triangle; for LOS each antenna must see half that distance, which needs a tower of about 565 m.
Teacher's Note:
1. Take the path up and down as two equal sides of an isosceles triangle; the perpendicular from the satellite splits it into two right-angled triangles.
2. LOS between two antennas of equal height h has maximum distance 2√(2Rh).
Examination Note: Draw the triangle, find x and then d, and double it. Then use d = √(2Rh) for the height.
Answer:
From the figure, the largest peak-to-peak value of the wave is 100 V and the smallest is 20 V. So \( V_{max} = \dfrac{100}{2} = 50\ \text{V} \) and \( V_{min} = \dfrac{20}{2} = 10\ \text{V} \).
(i) \( m = \dfrac{V_{max}-V_{min}}{V_{max}+V_{min}}\times100 = \dfrac{50-10}{50+10}\times100 = 66.7\ \% \)
(ii) Peak carrier voltage \( V_c = \dfrac{V_{max}+V_{min}}{2} = \dfrac{50+10}{2} = 30\ \text{V} \)
(iii) Peak information voltage \( V_m = mV_c = 0.667\times30 = 20\ \text{V} \)
Percentage modulation = 66.7 %, Vc = 30 V, Vm = 20 V
In simple words: The envelope swings between 50 V and 10 V, so its middle value is the carrier (30 V) and its swing on either side is the message (20 V).
Teacher's Note:
1. Read peak-to-peak values from the graph and halve them to get peak values.
2. Vc + Vm = 50 V and Vc − Vm = 10 V give the same answers.
Examination Note: Convert peak-to-peak readings to peak values before using the formula.
(ii) Is the plot symmetrical about ωc? Comment especially about plot in region ω < ωc. (iii) Extrapolate and predict the problems one can expect if more waves are to be modulated. (iv) Suggest solutions to the above problem. In the process can one understand another advantage of modulation in terms of bandwidth?
Answer:
(i) The spectrum is drawn in the figure. It has the carrier \( \omega_c \), the side bands \( \omega_c\pm\omega_1 \) and \( \omega_c\pm\omega_2 \) around it, and, because the modulator is a non-linear device, the low-frequency message components \( \omega_1 \), \( \omega_2 \) and their combinations \( \omega_2-\omega_1 \) and \( \omega_1+\omega_2 \) at the low-frequency end.
(ii) The carrier and its side bands alone are symmetrical about \( \omega_c \), but the complete plot is not symmetrical. The region \( \omega<\omega_c \) is crowded: it holds the lower side bands together with the low-frequency message components, while the region above \( \omega_c \) holds only the upper side bands.
(iii) If more signals are modulated, there will be still more components in the crowded region \( \omega<\omega_c \). Their frequencies overlap, so the signals can mix and interfere with one another.
(iv) To accommodate more signals we must increase the bandwidth available, by using a carrier of much higher frequency so that the side bands are far away from the low-frequency region and each signal has its own space. This shows another advantage of modulation: a high carrier frequency gives a large bandwidth, so many signals can be sent together.
In simple words: Using a higher carrier frequency moves the useful signals far away from the crowded low-frequency end and leaves room for many separate channels.
Teacher's Note:
1. A carrier of high frequency also allows a short antenna to be used.
2. Each signal needs a band of about twice its highest frequency; the available bandwidth limits the number of signals.
Examination Note: Draw the spectrum with all frequencies labelled, point out the crowded region and give the remedy of a higher carrier frequency.
Question 30. An audio signal is modulated by a carrier wave of 20 MHz such that the bandwidth required for modulation is 3 kHz. Could this wave be demodulated by a diode detector which has the values of R and C as (i) R = 1 kΩ, C = 0.01 μF. (ii) R = 10 kΩ, C = 0.01 μF. (iii) R = 10 kΩ, C = 0.1 μF.
Answer:
The bandwidth is \( 2f_m = 3\ \text{kHz} \), so \( f_m = 1.5\ \text{kHz} \). The carrier frequency is \( f_c = 20\ \text{MHz} \).
A diode detector can demodulate the wave if \( \dfrac{1}{f_c} \ll RC < \dfrac{1}{f_m} \). Here \( \dfrac{1}{f_c} = \dfrac{1}{20\times10^{6}} = 5\times10^{-8}\ \text{s} \) and \( \dfrac{1}{f_m} = \dfrac{1}{1.5\times10^{3}} = 6.7\times10^{-4}\ \text{s} \).
(i) \( RC = 10^{3}\times0.01\times10^{-6} = 10^{-5}\ \text{s} \). This is much larger than \( 5\times10^{-8} \) s and smaller than \( 6.7\times10^{-4} \) s, so the condition is satisfied: it can be demodulated.
(ii) \( RC = 10^{4}\times0.01\times10^{-6} = 10^{-4}\ \text{s} \). This is also between the two limits, so it can be demodulated.
(iii) \( RC = 10^{4}\times0.1\times10^{-6} = 10^{-3}\ \text{s} \). This is larger than \( 1/f_m = 6.7\times10^{-4} \) s, so the condition is not satisfied: it cannot be demodulated, because the capacitor discharges too slowly to follow the envelope of the message.
In simple words: The time constant RC must be long compared with a carrier cycle but short compared with one cycle of the message, and only the first two circuits satisfy this.
Teacher's Note:
1. If RC is too small, the carrier ripple appears in the output; if it is too large, the output cannot follow the falling envelope.
2. Take care with units: 1 μF = 10−6 F and 0.01 μF = 10−8 F.
Examination Note: Calculate the two limits first and then the RC of each circuit. Compare each with both limits.