Step-by-Step Pradeep's KL Gogia Solutions for Class 12 Physics Chapter 16 Solid And Semiconductor
Explore reliable textbook solutions for Chapter 16 Solid And Semiconductor tailored for Class 12 learners using Pradeep's KL Gogia methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.
Download Chapter 16 Solid And Semiconductor Textbook Solutions PDF
Access the complete solution PDF for Class 12 Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Solids and Semi-conductor - Pages 1-12
Examples
Question 2. A Ge specimen is doped with Al. The concentration of acceptor atoms is ~1021 atoms/m3. Given that the intrinsic concentration of electron hole pairs is ~1019/m3, the concentration of electrons in the specimen is [AIIMS 2004]
(a) 1017/m3 (b) 1015/m3 (c) 104/m3 (d) 102/m3
Solution. (a). ni2 = nhne ⇒ (1019)2 = 1021 × ne ⇒ ne = 1017/m3.
Teacher's Note: Use the mass-action law ni² = nenh; holes equal acceptor density.
Exam Note: Write the law first, then substitute.
Question 3. A silicon specimen is made into a P-type semiconductor by doping, on an average, one Indium atom per 5 × 107 silicon atoms. If the number density of atoms in the silicon specimen is 5 × 1028 atoms/m3, then the number of acceptor atoms in silicon will be
(a) 2.5 × 1030 atoms/cm3 (b) 1.0 × 1013 atoms/cm3 (c) 1.0 × 1015 atoms/cm3 (d) 2.5 × 1036 atoms/cm3
Solution. (c). Number density of atoms in silicon = 5 × 1028 atom/m3 = 5 × 1022 atom/cm3. Since one indium atom is doped in 5 × 107 Si atoms, the number of indium atoms per cm3 is n = (5 × 1022)/(5 × 107) = 1 × 1015 atom/cm3.
Teacher's Note: Convert m³ to cm³ (divide by 106) before dividing by the doping ratio.
Exam Note: Unit conversion is the usual trap.
Question 4. A P-type semiconductor has acceptor levels 57 meV above the valence band. The maximum wavelength of light required to create a hole is (Planck's constant h = 6.6 × 10−34 J-s)
(a) 57 Å (b) 57 × 10−3 Å (c) 217100 Å (d) 11.61 × 10−33 Å
Solution. (c). E = hc/λ ⇒ λ = hc/E = (6.6 × 10−34 × 3 × 108)/(57 × 10−3 × 1.6 × 10−19) = 217100 Å.
Teacher's Note: Photon energy must equal the acceptor gap; convert meV to joules using 1.6 × 10−19.
Exam Note: Convert meV to J, then m to Å.
Question 5. A potential barrier of 0.50 V exists across a P-N junction. If the depletion region is 5.0 × 10−7 m wide, the intensity of the electric field in this region is [UPSEAT 2002]
(a) 1.0 × 106 V/m (b) 1.0 × 105 V/m (c) 2.0 × 105 V/m (d) 2.0 × 106 V/m
Solution. (a). E = V/d = 0.50/(5 × 10−7) = 1 × 106 V/m.
Teacher's Note: Treat the depletion layer as a uniform field region: E = V/d.
Exam Note: One-line formula; mark units V/m.
Question 6. A 2 V battery is connected across the points A and B as shown in the figure. Assuming that the resistance of each diode is zero in forward bias and infinity in reverse bias, the current supplied by the battery when its positive terminal is connected to A is
(a) 0.2 A (b) 0.4 A (c) Zero (d) 0.1 A
Figure (described): two parallel branches between A and B. The upper branch has a diode in series with a 10 Ω resistor; the lower branch has a diode, pointing the opposite way, in series with a 10 Ω resistor.
Solution. (a). The diode in the upper branch is forward biased and the one in the lower branch is reverse biased. So current i = V/(R + rd), where rd = diode resistance in forward bias = 0. So i = V/R = 2/10 = 0.2 A.
Teacher's Note: Only the forward-biased branch conducts; the reverse-biased branch is an open circuit.
Exam Note: State which diode conducts to earn the method mark.
Question 7. Current in the circuit will be
(a) 5/40 A (b) 5/50 A (c) 5/10 A (d) 5/20 A
Figure (described): three parallel branches. The upper branch has a 20 Ω resistor and a diode; the middle branch has a diode and a 30 Ω resistor; the lower branch has a 20 Ω resistor and a 5 V cell. The current i is the total current from the cell.
Solution. (b). The diode in the lower branch is forward biased and the diode in the upper branch is reverse biased. ∴ i = 5/(20 + 30) = 5/50 A.
Teacher's Note: Reverse-biased branch carries no current; add the resistors in the conducting path in series.
Exam Note: Identify the conducting path before adding resistances.
Question 8. Find the magnitude of current in the following circuit [RPMT 2001]
(a) 0 (b) 1 amp (c) 0.1 amp (d) 0.2 amp
Figure (described): a series circuit of a 4 V cell, a diode, a 3 Ω resistor and a 1 V cell, with the cells' polarities as shown in the book figure.
Solution. (a). The diode is reverse biased. Therefore no current will flow through the circuit.
Teacher's Note: A reverse-biased ideal diode blocks current regardless of the resistor value.
Exam Note: Decide the bias first; then no calculation is needed.
Question 9. The diode used in the circuit shown in the figure has a constant voltage drop of 0.5 V at all currents and a maximum power rating of 100 milliwatts. What should be the value of the resistor R, connected in series with the diode for obtaining maximum current?
(a) 1.5 Ω (b) 5 Ω (c) 6.67 Ω (d) 200 Ω
Figure (described): a series loop of a resistor R, a diode with 0.5 V drop, and a 1.5 V cell.
Solution. (b). The current through the circuit i = P/V = (100 × 10−3)/0.5 = 0.2 A. ∴ voltage drop across the resistance = 1.5 − 0.5 = 1 V ⇒ R = 1/0.2 = 5 Ω.
Teacher's Note: Diode power P = Vd·i gives the maximum current; the rest of the EMF drops across R.
Exam Note: Use the diode's 0.5 V, not the 1.5 V supply, for power.
Question 10. For a transistor amplifier in common emitter configuration for load impedance of 1 kΩ (hfe = 50 and hoe = 25) the current gain is
(a) − 5.2 (b) − 15.7 (c) − 24.8 (d) − 48.78
Solution. (d). In common emitter configuration current gain Ai = −hfe/(1 + hoeRL) = −50/(1 + 25 × 10−6 × 103) = −48.78.
Teacher's Note: hoe is in µS here, so hoeRL = 0.025; the negative sign shows phase reversal.
Exam Note: Remember the 10−6 factor for hoe.
Question 11. In the following common emitter configuration an NPN transistor with current gain β = 100 is used. The output voltage of the amplifier will be [AIIMS 2003]
(a) 10 mV (b) 0.1 V (c) 1.0 V (d) 10 V
Figure (described): a 1 mV signal source in the base circuit with a 1 kΩ resistor; the collector circuit has a 10 kΩ load resistor, with Vout taken across it.
Solution. (c). Voltage gain = Output voltage/Input voltage ⇒ Vout = Vin × voltage gain. Vout = Vin × current gain × resistance gain = Vin × β × (RL/RBE) = 10−3 × 100 × (10/1) = 1 V.
Teacher's Note: Voltage gain = β × RL/Rin; here 100 × 10 = 1000.
Exam Note: Use the resistance ratio, not just β.
Question 12. While a collector to emitter voltage is constant in a transistor, the collector current changes by 8.2 mA when the emitter current changes by 8.3 mA. The value of forward current ratio hfe is
(a) 82 (b) 83 (c) 8.2 (d) 8.3
Solution. (a). hfe = (Δic/Δib) at constant Vce = 8.2/(8.3 − 8.2) = 82.
Teacher's Note: Base current change is Δie − Δic = 0.1 mA; then β = Δic/Δib.
Exam Note: First find Δib by subtraction.
Question 13. The transfer ratio of a transistor is 50. The input resistance of the transistor when used in the common-emitter configuration is 1 kΩ. The peak value for an ac input voltage of 0.01 V peak is
(a) 100 µA (b) 0.01 mA (c) 0.25 mA (d) 500 µA
Solution. (d). ic = βib = β × Vi/Ri = 50 × 0.01/1000 = 500 × 10−6 A = 500 µA.
Teacher's Note: Base current = Vi/Ri; multiply by β for the peak collector current.
Exam Note: The asked peak value is collector current.
Question 14. In a common base amplifier circuit, calculate the change in base current if that in the emitter current is 2 mA and α = 0.98 [BHU 1995]
(a) 0.04 mA (b) 1.96 mA (c) 0.98 mA (d) 2 mA
Solution. (a). Δic = αΔie = 0.98 × 2 = 1.96 mA. ∴ Δib = Δie − Δic = 2 − 1.96 = 0.04 mA.
Teacher's Note: Emitter current splits into collector and base: ie = ic + ib.
Exam Note: Subtract collector change from emitter change.
Free study material for Physics
Download Pradeep's KL Gogia Solutions for Class 12 Math PDF
Download Pradeep's KL Gogia Solutions for Class 12
Access the complete chapter-wise PDF for Pradeep's KL Gogia Solutions Physics Chapter 16 Solid And Semiconductor. These structured Pradeep's KL Gogia Solutions solutions for Class 12 Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Detailed Calculation Guides for Class 12
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Complete Your Class 12 Exam Preparation
In addition to these Pradeep's KL Gogia Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the Pradeep's KL Gogia book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.