Official Pradeep's KL Gogia Textbook Solutions: Class 12 Physics Chapter 02 Current Electricity
Access comprehensive textbook solutions for Chapter 02 Current Electricity using the Pradeep's KL Gogia reference material for Class 12 Physics. Designed to align with the 2026 academic curriculum, these detailed answers help students reinforce core academic concepts and master complex problem-solving methods.
Chapter-wise Solutions for Physics: Chapter 02 Current Electricity
View or download the dedicated Chapter 02 Current Electricity solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Physics.
1. Chemical Reactions and Equations
Current Electricity - Examples and Tricky Examples (pages 29-56)
Examples (continued)
Question Example 45. A wire of resistance 0.5 Ω m-1 is bent into a circle of radius 1 m. The same wire is connected across a diameter AB as shown in fig. The equivalent resistance is (a) π ohm (b) π(π + 2) ohm (c) π/(π + 4) ohm (d) (π + 1) ohm. (Figure: a circle with a straight wire along diameter AB; current i enters at A and leaves at B.)
Solution. (c). Resistance of upper semicircle = resistance of lower semicircle = 0.5 × (πR) = 0.5π Ω. Resistance of wire AB = 0.5 × 2 = 1 Ω. Hence the three resistances 0.5π Ω, 1 Ω and 0.5π Ω are in parallel between A and B: 1/RAB = 1/(0.5π) + 1/1 + 1/(0.5π) ⇒ RAB = π/(π + 4) Ω.
Teacher's Note: Diameter wire and the two semicircular arcs are three parallel branches between A and B.
Exam Note: Find each branch resistance first, then add reciprocals.
Question Example 46. A wire of resistor R is bent into a circular ring of radius r. Equivalent resistance between two points X and Y on its circumference, when angle XOY is α, can be given by (a) (Rα/4π2)(2π − α) (b) (R/2π)(2π − α) (c) R(2π − α) (d) (4π/Rα)(2π − α). (Figure: ring with centre O, points X and Y on it, W and Z on the ring on either side; angle XOY = α.)
Solution. (a). Here RXWY = (R/2πr) × (rα) = Rα/2π (since α = l/r) and RXZY = (R/2πr) × r(2π − α) = (R/2π)(2π − α).
Req = RXWY RXZY / (RXWY + RXZY) = [(Rα/2π) × (R/2π)(2π − α)] / [Rα/2π + R(2π − α)/2π] = (Rα/4π2)(2π − α).
Teacher's Note: Resistance of an arc is proportional to its length; the two arcs are in parallel.
Exam Note: Use arc length = rα for the angle.
Question Example 47. [RPET 2000] If in the given figure i = 0.25 amp, then the value R will be (a) 48 Ω (b) 12 Ω (c) 120 Ω (d) 42 Ω. (Figure: a 12 V battery in series with resistor R, and a parallel combination of 60 Ω, 20 Ω and 10 Ω resistors; current i flows.)
Solution. (d). i = 0.25 A, V = 12 V, so Req = V/i = 12/0.25 = 48 Ω. From the circuit, Req = R + (60 ∥ 20 ∥ 10) = R + 6, since 1/60 + 1/20 + 1/10 = 1/6. ⇒ R = Req − 6 = 48 − 6 = 42 Ω.
Teacher's Note: Reduce the parallel block (6 Ω) first, then use Req = V/i.
Exam Note: Show the parallel calculation for marks.
Question Example 48. [MNR 1994] Two uniform wires A and B are of the same metal and have equal masses. The radius of wire A is twice that of wire B. The total resistance of A and B when connected in parallel is (a) 4 Ω when the resistance of wire A is 4.25 Ω (b) 5 Ω when the resistance of wire A is 4 Ω (c) 4 Ω when the resistance of wire B is 4.25 Ω (d) 5 Ω when the resistance of wire B is 4 Ω.
Solution. (a). Density and masses of the wires are the same, so their volumes are equal: A1l1 = A2l2. Ratio of resistances RA/RB = (l1/l2) × (A2/A1) = (A2/A1)2 = (r2/r1)4. Since r1 = 2r2, RA/RB = 1/16 ⇒ RB = 16RA. In parallel, R = RARB/(RA + RB) = 16RA/17. Checking the options, only (a) is correct (RA = 4.25 Ω gives R = 16 × 4.25/17 = 4 Ω).
Teacher's Note: Equal mass means equal volume, so R ∝ 1/r4.
Exam Note: State R ∝ 1/r4 at fixed volume.
Tricky Examples
Question Tricky Example 5. [IIT-JEE 1991] The effective resistance between points P and Q of the electrical circuit shown in the figure is (a) 2Rr/(R + r) (b) 8R(R + r)/(3R + r) (c) 2r + 4R (d) 5R/2 + 2r. (Figure: between P and Q, three parallel horizontal branches: top branch 2R then 2R, middle branch r then r, bottom branch 2R then 2R; the midpoints of the top, middle and bottom branches are joined by two vertical resistors of 2R each.)
Solution. (a). The midpoints A, O and B are at the same potential, so the vertical 2R resistors carry no current and can be removed. The circuit is then three parallel branches: 2R + 2R = 4R, r + r = 2r, and 2R + 2R = 4R. Req = 4R ∥ 2r ∥ 4R, i.e. 1/Req = 1/4R + 1/2r + 1/4R = (R + r)/(2Rr), so Req = 2Rr/(R + r).
Teacher's Note: Symmetry makes the three midpoints equipotential, so the cross links carry no current.
Exam Note: Justify removing the links by equal potential.
Question Tricky Example 6. In the following circuit if key K is pressed then the galvanometer reading becomes half. The resistance of galvanometer is (a) 20 Ω (b) 30 Ω (c) 40 Ω (d) 50 Ω. (Figure: a cell, resistor R and galvanometer G in series; a shunt S = 40 Ω is connected across G through key K.)
Solution. (c). The galvanometer reading becoming half means the current divides equally between the galvanometer and the 40 Ω resistance. Hence the galvanometer resistance must be 40 Ω.
Teacher's Note: Equal current division in parallel means equal resistances (assuming the main current stays unchanged).
Exam Note: Use current divider: G·ig = S·is.
Question Example 49. A new flashlight cell of emf 1.5 volts gives a current of 15 amps, when connected directly to an ammeter of resistance 0.04 Ω. The internal resistance of cell is (a) 0.04 Ω (b) 0.06 Ω (c) 0.10 Ω (d) 10 Ω
Solution. (b). By using i = E/(R + r): 15 = 1.5/(0.04 + r) ⇒ r = 0.06 Ω.
Teacher's Note: The ammeter is the only external resistance, so apply i = E/(R + r) directly.
Exam Note: Write the formula and substitute.
Question Example 50. For a cell, the terminal potential difference is 2.2 V when the circuit is open and reduces to 1.8 V, when the cell is connected across a resistance, R = 5 Ω. The internal resistance of the cell is (a) 10/9 Ω (b) 9/10 Ω (c) 11/9 Ω (d) 5/9 Ω
Solution. (a). In open circuit, E = V = 2.2 V; in closed circuit, V = 1.8 V, R = 5 Ω. So internal resistance r = (E/V − 1)R = (2.2/1.8 − 1) × 5 ⇒ r = 10/9 Ω.
Teacher's Note: Open-circuit terminal voltage equals emf; use r = (E/V − 1)R.
Exam Note: Identify E from the open circuit.
Question Example 51. [CBSE PMT 1999; AFMC 1999; MP PET 1993; CPMT 1990] The internal resistance of a cell of emf 2V is 0.1 Ω. It's connected to a resistance of 3.9 Ω. The voltage across the cell will be (a) 0.5 volt (b) 1.9 volt (c) 1.95 volt (d) 2 volt
Solution. (c). By using r = (E/V − 1)R ⇒ 0.1 = (2/V − 1) × 3.9 ⇒ V = 1.95 volt.
Teacher's Note: Terminal voltage is less than emf by the drop ir inside the cell.
Exam Note: Check: i = 0.5 A, V = 2 − 0.05.
Question Example 52. When the resistance of 2 Ω is connected across the terminal of the cell, the current is 0.5 amp. When the resistance is increased to 5 Ω, the current is 0.25 amp. The emf of the cell is (a) 1.0 volt (b) 1.5 volt (c) 2.0 volt (d) 2.5 volt
Solution. (b). By using E = [i1i2/(i2 − i1)](R1 − R2) = [0.5 × 0.25/(0.25 − 0.5)](2 − 5) = 1.5 volt.
Teacher's Note: Two readings give E and r; solving 0.5(2 + r) = 0.25(5 + r) gives r = 1 Ω.
Exam Note: Use the short-trick formula for E and r.
Question Example 53. A primary cell has an emf of 1.5 volts, when short-circuited it gives a current of 3 amperes. The internal resistance of the cell is (a) 4.5 ohm (b) 2 ohm (c) 0.5 ohm (d) 1/4.5 ohm
Solution. (c). isc = E/r ⇒ 3 = 1.5/r ⇒ r = 0.5 Ω.
Teacher's Note: Short circuit means external R = 0, so the whole emf drives current through r.
Exam Note: Use isc = E/r.
Question Example 54. [IIT-JEE 1995] A battery of internal resistance 4 Ω is connected to the network of resistances as shown. In order to give the maximum power to the network, the value of R (in Ω) should be (a) 4/9 (b) 8/9 (c) 2 (d) 18. (Figure: battery E in series with a network of resistors R, R, R, 6R, R, R and 4R forming a bridge; as redrawn in the solution the bridge arms are R, 2R on one side and 2R, 4R on the other, with 6R across the middle.)
Solution. (c). The equivalent circuit is a balanced Wheatstone bridge (R/2R = 2R/4R), so the 6R resistor carries no current. The network reduces to (R + 2R) = 3R in parallel with (2R + 4R) = 6R. For maximum power transfer, external resistance should be equal to the internal resistance of the source: (R + 2R)(2R + 4R)/[(R + 2R) + (2R + 4R)] = 4, i.e. (3R × 6R)/(3R + 6R) = 4 ⇒ 2R = 4 or R = 2 Ω.
Teacher's Note: Balanced bridge removes 6R; maximum power needs external resistance equal to internal resistance.
Exam Note: State the maximum power transfer condition Rext = r.
Question Example 55. A torch bulb rated as 4.5 W, 1.5 V is connected as shown in the figure. The emf of the cell needed to make the bulb glow at full intensity is (a) 4.5 V (b) 1.5 V (c) 2.67 V (d) 13.5 V. (Figure: the bulb in parallel with a 1 Ω resistor, connected to a cell of emf E and internal resistance r; the value of r is cut off in the printed figure and is 2.67 Ω from the solution.)
Solution. (d). When the bulb glows with full intensity, the potential difference across it is 1.5 V. So the current through the bulb is 4.5/1.5 = 3 A, and the current through the 1 Ω resistor is 1.5/1 = 1.5 A. So the main current from the cell i = 3 + 1.5 = 4.5 A. By using E = V + ir ⇒ E = 1.5 + 4.5 × 2.67 = 13.5 V.
Teacher's Note: Find branch currents at rated voltage, add them, then use E = V + ir.
Exam Note: Use P = Vi for the bulb current.
Question Tricky Example 7. Potential difference across the terminals of the battery shown in figure is (r = internal resistance of battery) (a) 8 V (b) 10 V (c) 6 V (d) Zero. (Figure: a 10 V battery with r = 1 Ω; its terminals are joined by a wire in the figure, with a 4 Ω resistor in a separate branch.)
Solution. (d). The battery is short circuited, so the potential difference across its terminals is zero.
Teacher's Note: A zero-resistance wire across the terminals gives V = E − ir = 0 with i = E/r.
Exam Note: Name it a short circuit; terminal V = 0.
Grouping of Cells
Question Example 56. [KCET 2003] A group of N cells whose emf varies directly with the internal resistance as per the equation EN = 1.5 rN are connected as shown in the following figure. The current i in the circuit is (a) 0.51 amp (b) 5.1 amp (c) 0.15 amp (d) 1.5 amp. (Figure: N cells numbered 1, 2, 3, 4, ..., N with internal resistances r1, r2, r3, r4, ..., rN joined end to end in a closed ring, with no external resistance.)
Solution. (d). i = Eeq/req = (1.5r1 + 1.5r2 + 1.5r3 + ......)/(r1 + r2 + r3 + ......) = 1.5 amp.
Teacher's Note: Cells in series in a closed loop: emfs add and internal resistances add.
Exam Note: Factor out 1.5 from the numerator sum.
Question Example 57. [MP PET 2001] Two batteries A and B each of emf 2 volt are connected in series to external resistance R = 1 Ω. Internal resistance of A is 1.9 Ω and that of B is 0.9 Ω, what is the potential difference between the terminals of battery A (a) 2 V (b) 3.8 V (c) 0 (d) None of these. (Figure: cells A and B in series with resistor R in a single loop.)
Solution. (c). i = (E1 + E2)/(R + r1 + r2) = (2 + 2)/(1 + 1.9 + 0.9) = 4/3.8 A. Hence VA = EA − irA = 2 − (4/3.8) × 1.9 = 0.
Teacher's Note: Terminal voltage = emf minus ir; here the drop inside A exactly equals its emf.
Exam Note: First find the series current.
Question Example 58. In a mixed grouping of identical cells 5 rows are connected in parallel by each row contains 10 cell. This combination send a current i through an external resistance of 20 Ω. If the emf and internal resistance of each cell is 1.5 volt and 1 Ω respectively then the value of i is (a) 0.14 (b) 0.25 (c) 0.75 (d) 0.68
Solution. (d). No. of cells in a row n = 10; no. of such rows m = 5. i = nE/(R + nr/m) = (10 × 1.5)/(20 + 10 × 1/5) = 15/22 = 0.68 amp.
Teacher's Note: Row emf is nE; the m rows in parallel give internal resistance nr/m.
Exam Note: Quote i = nE/(R + nr/m).
Question Example 59. To get maximum current in a resistance of 3 Ω one can use n rows of m cells connected in parallel. If the total no. of cells is 24 and the internal resistance of a cell is 0.5 then (a) m = 12, n = 2 (b) m = 8, n = 4 (c) m = 2, n = 12 (d) m = 6, n = 4
Solution. (a). In this question R = 3 Ω, mn = 24, r = 0.5 Ω and R = mr/n. On putting the values we get n = 2 and m = 12.
Teacher's Note: Maximum current needs external R equal to the grouped internal resistance mr/n; combine with mn = 24.
Exam Note: Check: 12 × 0.5/2 = 3 Ω.
Question Example 60. 100 cells each of emf 5 V and internal resistance 1 Ω are to be arranged so as to produce maximum current in a 25 Ω resistance. Each row contains equal number of cells. The number of rows should be (a) 2 (b) 4 (c) 5 (d) 100
Solution. (a). Total no. of cells mn = 100 ........ (i). Current will be maximum when R = nr/m; 25 = n × 1/m ⇒ n = 25m ........ (ii). From equations (i) and (ii), n = 50 and m = 2 (here n is the number of cells in a row and m the number of rows).
Teacher's Note: Set R = nr/m and mn = 100; solve for the number of rows m.
Exam Note: Answer asks rows (m), not cells per row.
Question Example 61. In the adjoining circuit, the battery E1 has an emf of 12 volt and zero internal resistance, while the battery E has an emf of 2 volt. If the galvanometer reads zero, then the value of resistance X ohm is (a) 10 (b) 100 (c) 500 (d) 200. (Figure: battery E1 (12 V) in a loop with a 500 Ω resistor and the resistor X Ω; the galvanometer G in series with the cell E (2 V) is connected between point Q, the junction of 500 Ω and X, and point B.)
Solution. (b). For zero deflection in the galvanometer, the potential difference across X must equal the emf E = 2 V. In this condition 12X/(500 + X) = 2, ∴ X = 100 Ω.
Teacher's Note: Null deflection means no current in the E branch; p.d. across X balances E.
Exam Note: Apply the potential divider across X.
Question Example 62. In the circuit shown here E1 = E2 = E3 = 2 V and R1 = R2 = 4 Ω. The current flowing between point A and B through battery E2 is (a) Zero (b) 2 A from A to B (c) 2 A from B to A (d) None of these. (Figure: three cells E1, E2, E3 in parallel branches between the left node A and, through resistors R1 (top branch) and R2 (bottom branch), the right node B; E2 is the middle branch directly between A and B.)
Solution. (b). The equivalent circuit can be drawn since E1 and E3 are parallel: a 2 V cell (E1 ∥ E3) in series with 2 V (E2) and R = (R1 ∥ R2) = 2 Ω. So current i = (2 + 2)/2 = 2 A from A to B.
Teacher's Note: Cells of equal emf in parallel act as one cell; resistors R1, R2 combine in parallel.
Exam Note: State direction A to B with the answer.
Question Example 63. [CPMT 1986, 88] The magnitude and direction of the current in the circuit shown will be (a) 7/3 A from a to b through e (b) 7/3 A from b and a through e (c) 1.0 A from b to a through e (d) 1.0 A from a to b through e. (Figure: loop a-b-c-d with 1 Ω, a 10 V cell, point e, a 4 V cell and 2 Ω along the top from a to b, and 3 Ω along the bottom.)
Solution. (d). Current i = (10 − 4)/(3 + 2 + 1) = 1 A from a to b via e.
Teacher's Note: Opposing cells: net emf is the difference; total resistance is the sum, and the larger emf fixes direction.
Exam Note: Net emf 6 V over 6 Ω.
Question Example 64. Figure represents a part of the closed circuit. The potential difference between points A and B (VA − VB) is (a) +9 V (b) −9 V (c) +3 V (d) +6 V. (Figure: from A to B: a 2 Ω resistor carrying 2 A, a 3 V cell, and a 1 Ω resistor.)
Solution. (a). The given part of a closed circuit can be redrawn as follows. It should be remembered that the product of current and resistance can be treated as an imaginary cell having emf = iR. The 2 Ω resistor acts as a 4 V cell, the 3 V cell stays, and the 1 Ω resistor acts as a 2 V cell; all aid, giving a 9 V cell with A positive. Hence VA − VB = +9 V.
Teacher's Note: Treat each iR drop as an equivalent emf and add along the path with signs.
Exam Note: Sum 4 + 3 + 2 along current direction.
Question Example 65. In the circuit shown below the cells E1 and E2 have emfs 4 V and 8 V and internal resistance 0.5 ohm and 1 ohm respectively. Then the potential difference across cell E1 and E2 will be (a) 3.75 V, 7.5 V (b) 4.25 V, 7.5 V (c) 3.75 V, 3.5 V (d) 4.25 V, 4.25 V. (Figure: E1 and E2 in series in a loop with a 4.5 Ω resistor in series with the parallel pair 3 Ω and 6 Ω.)
Solution. (b). In the given circuit diagram external resistance R = (3 × 6)/(3 + 6) + 4.5 = 6.5 Ω. Hence main current through the circuit i = (E2 − E1)/(R + req) = (8 − 4)/(6.5 + 0.5 + 1) = 4/8 = 1/2 amp. Corrected: the book prints the denominator as 6.5 + 0.5 + 0.5; req = 0.5 + 1 = 1.5 Ω, so the denominator is 8 Ω. Cell 1 is charging so from its emf equation E1 = V1 − ir1 ⇒ 4 = V1 − (1/2) × 0.5 ⇒ V1 = 4.25 volt. Cell 2 is discharging so from its emf equation E2 = V2 + ir2 ⇒ 8 = V2 + (1/2) × 1 ⇒ V2 = 7.5 volt.
Teacher's Note: Opposing cells: the weaker is charged, V = E + ir; the stronger discharges, V = E − ir.
Exam Note: Net emf 4 V over 8 Ω gives 0.5 A.
Question Example 66. A wire of length L and 3 identical cells of negligible internal resistances are connected in series. Due to this current, the temperature of the wire is raised by ΔT in time t. A number N of similar cells is now connected in series with a wire of the same material and cross-section but of length 2L. The temperature of wire is raised by same amount ΔT in the same time t. The value of N is (a) 4 (b) 6 (c) 8 (d) 9
Solution. (b). Heat = mSΔT = i2Rt. Case I: length L ⇒ resistance = R and mass = m. Case II: length 2L ⇒ resistance = 2R and mass = 2m. So m1S1ΔT1/(m2S2ΔT2) = i12R1t1/(i22r2t2) ⇒ mSΔT/(2mSΔT) = i12Rt/(i22 2Rt) ⇒ i1 = i2 ⇒ (3E)/R = (NE)/(2R) ⇒ N = 6. (The printed working shows the squared forms (3E)2, (NE)2 over 12 and 2R with the same result N = 6.)
Teacher's Note: Same ΔT means equal currents; doubling length doubles R, so the emf must double.
Exam Note: Mass and resistance both double with length.
Question Tricky Example 8. n identical cells, each of emf E and internal resistance r, are joined in series to form a closed circuit. The potential difference across any one cell is (a) Zero (b) E (c) E/n (d) ((n − 1)/n)E
Solution. (a). Current in the circuit i = nE/(nr) = E/r. The equivalent circuit of one cell is its emf E in series with r. Potential difference across the cell = VA − VB = −E + ir = −E + (E/r)·r = 0.
Teacher's Note: With no external resistance, each cell's emf is entirely used up in its own internal drop.
Exam Note: Find i = E/r first, then V = E − ir.
Kirchhoff's Laws: Examples
Question Example 67. [MP PET 2003] In the following circuit E1 = 4 V, R1 = 2 Ω, E2 = 6 V, R2 = 2 Ω and R3 = 4 Ω. The current i1 is (a) 1.6 A (b) 1.8 A (c) 2.25 A (d) 1 A. (Figure: two-loop circuit; the top branch has cell E1 and R1 carrying i1, the middle branch has R2, the bottom branch has cell E2 and R3 carrying i2.)
Solution. (b). Let the current in R2 be (i1 − i2). For loop (1): −2i1 − 2(i1 − i2) + 4 = 0 ⇒ 2i1 − i2 = 2 ...... (i). For loop (2): −4i2 + 2(i1 − i2) + 6 = 0 ⇒ 3i2 − i1 = 3 ...... (ii). After solving equations (i) and (ii) we get i1 = 1.8 A and i2 = 1.6 A.
Teacher's Note: Two independent loops give two equations; assign (i1 − i2) to the shared resistor.
Exam Note: Show both loop equations and the solving step.
Question Example 68. Determine the current in the following circuit (a) 1 A (b) 2.5 A (c) 0.4 A (d) 3 A. (Figure: single loop with a 10 V cell and a 2 Ω resistor on top, a 5 V cell and a 3 Ω resistor at the bottom, the cells opposing each other.)
Solution. (a). Applying KVL in the given circuit we get −2i + 10 − 5 − 3i = 0 ⇒ i = 1 A. Second method: similar plates of the two batteries are connected together, so the net emf = 10 − 5 = 5 V. Total resistance in the circuit = 2 + 3 = 5 Ω. ∴ i = ΣV/ΣR = 5/5 = 1 A.
Teacher's Note: Opposing cells subtract; the larger emf sets the direction.
Exam Note: Net emf 5 V over total 5 Ω.
Question Example 69. In the circuit shown in figure, find the current through the branch BD (a) 5 A (b) 0 A (c) 3 A (d) 4 A. (Figure: 15 V cell between A and D on the left, 6 Ω from A to B, 3 Ω from B to C, 30 V cell between C and D on the right, 3 Ω in branch BD.)
Solution. (a). Let the currents be i1 in 6 Ω, (i1 − i2) in 3 Ω (BC) and i2 in branch BD. KVL along loop ABDA: −6i1 − 3i2 + 15 = 0 or 2i1 + i2 = 5 ...... (i). KVL along loop BCDB: −3(i1 − i2) − 30 + 3i2 = 0 or −i1 + 2i2 = 10 ...... (ii). Solving equations (i) and (ii) for i2, we get i2 = 5 A (with i1 = 0).
Teacher's Note: Pick two loops, assign branch currents, and solve; the BD current is the unknown i2.
Exam Note: Verify by substituting both loop equations.
Question Example 70. [MP PMT 1995] The figure shows a network of currents. The magnitude of current i will be (a) 3 A (b) 13 A (c) 23 A (d) −3 A. (Figure: a square network; 15 A enters at the top-left corner, 3 A enters at the top-right corner, 5 A enters at the bottom-left corner, and current i leaves at the bottom-right corner.)
Solution. (c). i = 15 + 3 + 5 = 23 A.
Teacher's Note: Kirchhoff's current law on the whole network: total current in equals total current out.
Exam Note: Check each arrow direction before adding.
Question Example 71. [AMU 1995] Consider the circuit shown in the figure. The current i3 is equal to (a) 5 amp (b) 3 amp (c) −3 amp (d) −5/6 amp. (Figure: two loops sharing a middle branch with a 6 V cell carrying i3; left loop has 28 Ω and an 8 V cell, right loop has 54 Ω and a 12 V cell.)
Solution. (d). Suppose the currents through different paths of the circuit are i1 (left loop), i2 (right loop) and i3 = i1 + i2 in the middle branch. After applying KVL for loop (1) and loop (2) we get 28i1 = −6 − 8 ⇒ i1 = −1/2 A and 54i2 = −6 − 12 ⇒ i2 = −1/3 A. Hence i3 = i1 + i2 = −5/6 A.
Teacher's Note: Each loop contains one resistor and two cells; the middle current is the sum of the loop currents.
Exam Note: Negative sign means opposite to assumed direction.
Question Example 72. A part of a circuit in steady state along with the current flowing in the branches, with value of each resistance is shown in figure. What will be the energy stored in the capacitor C0 (a) 6 × 10-4 J (b) 8 × 10-4 J (c) 16 × 10-4 J (d) Zero. (Figure: part of a circuit in steady state with branch currents marked: 2 A in and 2 A out along the main line through 3 Ω and 1 Ω; 1 A entering at A through 3 Ω and 1 A leaving at B through 3 Ω; the 4 μF capacitor C0 joins A and B; the path A-D-C-B contains 5 Ω (current i1), 1 Ω (D to C) and 2 Ω (current i2); i3 flows on through 4 Ω.)
Solution. (b). Applying Kirchhoff's first law at junctions A and B respectively we have 2 + 1 − i1 = 0, i.e., i1 = 3 A and i2 + 1 − 2 = 0, i.e., i2 = 1 A. Now applying Kirchhoff's second law to the mesh ADCBA treating the capacitor as a seat of emf V in open circuit: −3 × 5 − 3 × 1 − 1 × 2 + V = 0, i.e., V (= VA − VB) = 20 V. So, energy stored in the capacitor U = ½CV2 = ½ × (4 × 10-6) × (20)2 = 8 × 10-4 J.
Teacher's Note: In steady state the capacitor carries no current; its voltage equals the drop along the parallel path.
Exam Note: Find V first, then use U = ½CV2.
Question Example 73. In the following circuit the potential difference between P and Q is (a) 15 V (b) 10 V (c) 5 V (d) 2.5 V. (Figure: P connected through resistor R, carrying 2 A, to Q; a 15 V cell E1 at P earthed, and a 5 Ω resistor at Q earthed through E2.)
Solution. (c). By using KVL −5 × 2 − VPQ + 15 = 0 ⇒ VPQ = 5 V.
Teacher's Note: Walk from the 15 V cell through the 5 Ω drop (2 A) to find VPQ.
Exam Note: Keep the signs of each potential change.
Question Tricky Example 9. As the switch S is closed in the circuit shown in figure, current passed through it is (a) 4.5 A (b) 6.0 A (c) 3.0 A (d) Zero. (Figure: point A at 20 V joined through 2 Ω, and point B at 5 V joined through 4 Ω, to a common junction; from the junction a 2 Ω resistor and the switch S go to earth.)
Solution. (a). Let V be the potential of the junction as shown in figure. Applying junction law, (20 − V)/2 + (5 − V)/4 = (V − 0)/2, or 40 − 2V + 5 − V = 2V, or 5V = 45 ⇒ V = 9 V. ∴ i3 = V/2 = 4.5 A.
Teacher's Note: Assume the junction potential V and apply the current law there instead of two loops.
Exam Note: Current in S is V/2, not V/4.
Different Measuring Instruments: Examples
Question Example 74. The scale of a galvanometer of resistance 100 Ω contains 25 divisions. It gives a deflection of one division on passing a current of 4 × 10-4 A. The resistance in ohms to be added to it, so that it may become a voltmeter of range 2.5 volt is (a) 100 (b) 150 (c) 250 (d) 300
Solution. (b). Current sensitivity of galvanometer = 4 × 10-4 A/div. So full scale deflection current (ig) = current sensitivity × total number of divisions = 4 × 10-4 × 25 = 10-2 A. To convert the galvanometer into a voltmeter, resistance to be put in series is R = V/ig − G = 2.5/10-2 − 100 = 150 Ω.
Teacher's Note: Full-scale current = sensitivity × divisions; series resistance R = V/ig − G.
Exam Note: Do not forget to subtract G.
Question Example 75. [EAMCET 2003] A galvanometer, having a resistance of 50 Ω gives a full scale deflection for a current of 0.05 A. The length in meter of a resistance wire of area of cross-section 2.97 × 10-2 cm2 that can be used to convert the galvanometer into an ammeter which can read a maximum of 5 A current is : (Specific resistance of the wire = 5 × 10-7 Ω-m) (a) 9 (b) 6 (c) 3 (d) 1.5
Solution. (c). Given G = 50 Ω, ig = 0.05 A, i = 5 A, A = 2.97 × 10-2 cm2 and ρ = 5 × 10-7 Ω-m. By using i/ig = 1 + G/S ⇒ S = G·ig/(i − ig) ⇒ ρl/A = G·ig/(i − ig) ⇒ l = G·ig·A/[(i − ig)ρ]; on putting values l = 3 m.
Teacher's Note: Shunt S = Gig/(i − ig) ≈ 0.505 Ω; then l = SA/ρ with A in m2.
Exam Note: Convert cm2 to m2.
Question Example 76. [KCET 2002; UPSEAT 1998; MNR 1994 Similar to MP PMT 1999] 100 mA current gives a full scale deflection in a galvanometer of 2 Ω resistance. The resistance connected with the galvanometer to convert it into a voltmeter of 5 V range is (a) 98 Ω (b) 52 Ω (c) 80 Ω (d) 48 Ω
Solution. (d). R = V/Ig − G = 5/(100 × 10-3) − 2 = 50 − 2 = 48 Ω.
Teacher's Note: Total resistance for 5 V at 100 mA is 50 Ω; subtract the coil's 2 Ω.
Exam Note: Convert mA to A first.
Question Example 77. A milliammeter of range 10 mA has a coil of resistance 1 Ω. To use it as voltmeter of range 10 volt, the resistance that must be connected in series with it will be (a) 999 Ω (b) 99 Ω (c) 1000 Ω (d) None of these
Solution. (a). By using R = V/ig − G ⇒ R = 10/(10 × 10-3) − 1 = 999 Ω.
Teacher's Note: Same series-resistor formula; 10 V at 10 mA needs 1000 Ω in total.
Exam Note: Answer is 999, not 1000.
Question Example 78. In the following figure ammeter and voltmeter reads 2 amp and 120 volt respectively. Resistance of voltmeter is (a) 100 Ω (b) 200 Ω (c) 300 Ω (d) 400 Ω. (Figure: ammeter in series with a 75 Ω resistor between points X and Y; the voltmeter is connected across X and Y, in parallel with the 75 Ω resistor.)
Solution. (c). Let resistance of voltmeter be RV. Equivalent resistance between X and Y is RXY = 75RV/(75 + RV). Reading of voltmeter = potential difference across X and Y = 120 = i × RXY = 2 × 75RV/(75 + RV) ⇒ RV = 300 Ω.
Teacher's Note: A real voltmeter is in parallel with the resistor, so the ammeter current splits between them.
Exam Note: Use V = i × R of the parallel pair.
Question Example 79. In the circuit shown in figure, the voltmeter reading would be (a) Zero (b) 0.5 volt (c) 1 volt (d) 2 volt. (Figure: a 3 V cell in series with 1 Ω and 2 Ω resistors; an ammeter A and a voltmeter V are connected in parallel with each other across the end of the circuit.)
Solution. (a). Ammeter has no resistance so there will be no potential difference across it, hence reading of voltmeter is zero.
Teacher's Note: The voltmeter is in parallel with an ideal ammeter, which has zero resistance and shorts it.
Exam Note: Parallel to zero resistance means zero p.d.
Question Example 80. Voltmeters V1 and V2 are connected in series across a d.c. line. V1 reads 80 V and has a per volt resistance of 200 Ω, V2 has a total resistance of 32 kΩ. The line voltage is (a) 120 V (b) 160 V (c) 220 V (d) 240 V
Solution. (d). Resistance of voltmeter V1 is R1 = 200 × 80 = 16000 Ω and resistance of voltmeter V2 is R2 = 32000 Ω. By using the relation V′ = (R′/Req)V, where V′ = potential difference across any resistance R′ in a series grouping, for voltmeter V1 the potential difference across it is 80 = [R1/(R1 + R2)]·V ⇒ V = 240 V.
Teacher's Note: Per-volt resistance times range gives the meter's resistance; series meters share voltage in proportion to resistance.
Exam Note: Use the potential divider rule.
Question Example 81. The resistance of 1 A ammeter is 0.018 Ω. To convert it into 10 A ammeter, the shunt resistance required will be (a) 0.18 Ω (b) 0.0018 Ω (c) 0.002 Ω (d) 0.12 Ω
Solution. (c). By using i/ig = 1 + G/S ⇒ 10/1 = 1 + 0.018/S ⇒ S = 0.002 Ω.
Teacher's Note: Range goes from 1 A to 10 A, so the shunt carries 9 A and the coil 1 A.
Exam Note: S = G/(n − 1) with n = 10.
Question Example 82. [CBSE PMT 1999] In meter bridge the balancing length from left and when standard resistance of 1 Ω is in right gap is found to be 20 cm. The value of unknown resistance is (a) 0.25 Ω (b) 0.4 Ω (c) 0.5 Ω (d) 4 Ω. (Figure: bridge with unknown X (left) and R = 1 Ω (right) in the top gaps, and wire segments P = 20r (20 cm) and Q = 80r (80 cm) below, galvanometer between the junctions.)
Solution. (a). The condition of Wheatstone bridge gives X/R = 20r/80r, r = resistance of wire per cm, X = unknown resistance. ∴ X = (20/80) × R = (1/4) × 1 = 0.25 Ω.
Teacher's Note: At balance X/R = l/(100 − l), with l measured on the side of the unknown resistance.
Exam Note: Quote the balance condition P/Q = X/R.
Question Example 83. [CBSE PMT 1998] A galvanometer having a resistance of 8 Ω is shunted by a wire of resistance 2 Ω. If the total current is 1 amp, the part of it passing through the shunt will be (a) 0.25 amp (b) 0.8 amp (c) 0.2 amp (d) 0.5 amp
Solution. (b). Fraction of current passing through the galvanometer: ig/i = S/(S + G), i.e., ig/i = 2/(2 + 8) = 0.2. So fraction of current passing through the shunt: is/i = 1 − ig/i = 1 − 0.2 = 0.8 amp.
Teacher's Note: Current divides inversely with resistance; the small shunt carries most of the current.
Exam Note: Galvanometer gets S/(S + G), shunt the rest.
Question Example 84. [MP PMT 1996] A moving coil galvanometer is converted into an ammeter reading upto 0.03 A by connecting a shunt of resistance 4r across it and into an ammeter reading upto 0.06 A when a shunt of resistance r connected across it. What is the maximum current which can be through this galvanometer if no shunt is used (a) 0.01 A (b) 0.02 A (c) 0.03 A (d) 0.04 A
Solution. (b). For ammeter, S = [ig/(i − ig)]G ⇒ igG = (i − ig)S. So igG = (0.03 − ig)4r ...... (i) and igG = (0.06 − ig)r ...... (ii). Dividing equation (i) by (ii): 1 = (0.03 − ig)4/(0.06 − ig) ⇒ 0.06 − ig = 0.12 − 4ig ⇒ 3ig = 0.06 ⇒ ig = 0.02 A.
Teacher's Note: The product igG is the same in both cases; dividing eliminates G and r.
Exam Note: Write igG = (i − ig)S for each shunt.
Question Tricky Example 10. The ammeter A reads 2 A and the voltmeter V reads 20 V. The value of resistance R is (a) Exactly 10 ohm (b) Less than 10 ohm (c) More than 10 ohm (d) We cannot definitely say. (Figure: ammeter in series with resistor R; the voltmeter is connected across the resistor R, in parallel with it.)
Solution. (c). If current goes through the resistance R is i then iR = 20 volt ⇒ R = 20/i. Since i < 2 A so R > 10 Ω.
Teacher's Note: The voltmeter draws some current, so the current through R is less than the ammeter reading.
Exam Note: Real voltmeter means ammeter reading exceeds iR.
Potentiometer
Application of Potentiometer: Examples
Question Example 85. A battery with negligible internal resistance is connected with 10 m long wire. A standard cell gets balanced on 600 cm length of this wire. On increasing the length of potentiometer wire by 2 m then the null point will be displaced by (a) 200 cm (b) 120 cm (c) 720 cm (d) 600 cm
Solution. (b). By using L1/L2 = l1/l2 ⇒ 10/12 = 600/l2 ⇒ l2 = 720 cm. Hence displacement = 720 − 600 = 120 cm.
Teacher's Note: Same p.d. across a longer wire lowers the gradient, so balancing length rises in proportion to wire length.
Exam Note: Answer asks displacement, not new length.
Question Example 86. In the following circuit a 10 m long potentiometer wire with resistance 1.2 ohm/m, a resistance R1 and an accumulator of emf 2 V are connected in series. When the emf of thermocouple is 2.4 mV then the deflection in galvanometer is zero. The current supplied by the accumulator will be (a) 4 × 10-4 A (b) 8 × 10-4 A (c) 4 × 10-3 A (d) 8 × 10-3 A. (Figure: accumulator, R1 and potentiometer wire AB in series; a thermocouple with hot and cold junctions is connected through a galvanometer to A and to a jockey at a balancing length of 5 m from A.)
Solution. (a). E = xl = iρl ∴ i = E/(ρl) = (2.4 × 10-3)/(1.2 × 5) = 4 × 10-4 A (the balance point is at l = 5 m, as marked in the figure).
Teacher's Note: At null point the thermo-emf equals i·ρ·l, the p.d. across the balancing length.
Exam Note: Use the balancing length 5 m, not 10 m.
Question Example 87. The resistivity of a potentiometer wire is 40 × 10-8 Ω m and its area of cross section is 8 × 10-6 m2. If 0.2 amp. Current is flowing through the wire, the potential gradient will be (a) 10-2 volt/m (b) 10-1 volt/m (c) 3.2 × 10-2 volt/m (d) 1 volt/m
Solution. (a). Potential gradient = V/L = iR/L = iρL/(AL) = iρ/A = (0.2 × 40 × 10-8)/(8 × 10-6) = 10-2 V/m.
Teacher's Note: Gradient x = iρ/A; length cancels out.
Exam Note: Quote x = iρ/A before substituting.
Question Example 88. [RPMT 1998] A deniel cell is balanced on 125 cm length of a potentiometer wire. When the cell is short circuited with a 2 Ω resistance the balancing length obtained is 100 cm. Internal resistance of the cell will be (a) 1.5 Ω (b) 0.5 Ω (c) 1.25 Ω (d) 4/5 Ω
Solution. (b). By using r = [(l1 − l2)/l2] × R′ ⇒ r = [(125 − 100)/100] × 2 = 1/2 = 0.5 Ω.
Teacher's Note: l1 gives emf, l2 the terminal voltage; r = (l1 − l2)R′/l2.
Exam Note: Longer length is the open-circuit one.
Question Example 89. A potentiometer wire of length 10 m and a resistance 30 Ω is connected in series with a battery of emf 2.5 V and internal resistance 5 Ω and an external resistance R. If the fall of potential along the potentiometer wire is 50 μV/mm, the value of R is (in Ω) (a) 115 (b) 80 (c) 50 (d) 100
Solution. (a). By using x = [e/(R + Rh + r)]·(R/L) ⇒ (50 × 10-6)/10-3 = [2.5/(30 + R + 5)] × (30/10) ⇒ R = 115 Ω.
Teacher's Note: Convert 50 μV/mm to 0.05 V/m, then use x = eRwire/[(Rtotal)L].
Exam Note: Unit conversion is where marks are lost.
Question Example 90. [AIIMS 1982] A 2 volt battery, a 15 Ω resistor and a potentiometer of 100 cm length, all are connected in series. If the resistance of potentiometer wire is 5 Ω, then the potential gradient of the potentiometer wire is (a) 0.005 V/cm (b) 0.05 V/cm (c) 0.02 V/cm (d) 0.2 V/cm
Solution. (a). By using x = [e/(R + Rh + r)]·(R/L) ⇒ x = [2/(5 + 15 + 0)] × (5/1) = 0.5 V/m = 0.005 V/cm.
Teacher's Note: Current is 2/20 = 0.1 A; p.d. over the 5 Ω wire is 0.5 V across 1 m.
Exam Note: Convert V/m to V/cm.
Question Example 91. In an experiment to measure the internal resistance of a cell by potentiometer, it is found that the balance point is at a length of 2 m when the cell is shunted by a 5 Ω resistance; and is at a length of 3 m when the cell is shunted by a 10 Ω resistance. The internal resistance of the cell is, then (a) 1.5 Ω (b) 10 Ω (c) 15 Ω (d) 1 Ω
Solution. (b). By using r = [(l1 − l2)/l2]R′ ⇒ r = [(l1 − 2)/2] × 5 ...... (i) and r = [(l1 − 3)/3] × 10 ...... (ii). On solving (i) and (ii), r = 10 Ω (with l1 = 6 m).
Teacher's Note: Same cell, same open-circuit length l1 in both runs; equate the two expressions for r.
Exam Note: Eliminate l1 first, then find r.
Question Example 92. A resistance of 4 Ω and a wire of length 5 metres and resistance 5 Ω are joined in series and connected to a cell of emf 10 V and internal resistance 1 Ω. A parallel combination of two identical cells is balanced across 300 cm of the wire. The emf E of each cell is (a) 1.5 V (b) 3.0 V (c) 0.67 V (d) 1.33 V. (Figure: 10 V, 1 Ω cell in series with the 4 Ω resistor and the 5 m, 5 Ω wire; two cells of emf E in parallel connected through a galvanometer to the wire with the jockey at 3 m.)
Solution. (b). By using Eeq = [e/(R + Rh + r)]·(R/L) × l ⇒ E = [10/(5 + 4 + 1)] × (5/5) × 3 ⇒ E = 3 volt.
Teacher's Note: Two identical cells in parallel have emf E; gradient is (10/10 A) × 1 Ω/m = 1 V/m.
Exam Note: Primary current includes the 4 Ω and 1 Ω.
Question Example 93. [MP PMT 2002; RPMT 2000] A potentiometer has uniform potential gradient across it. Two cells connected in series (i) to support each other and (ii) to oppose each other are balanced over 6 m and 2 m respectively on the potentiometer wire. The emf's of the cells are in the ratio of (a) 1 : 2 (b) 1 : 1 (c) 3 : 1 (d) 2 : 1
Solution. (d). If suppose emf's of the cells are E1 and E2 respectively then E1 + E2 = x × 6 ...... (i) and E1 − E2 = x × 2 ...... (ii) (x = potential gradient) ⇒ (E1 + E2)/(E1 − E2) = 3/1 ⇒ E1/E2 = 2/1.
Teacher's Note: Aiding cells add, opposing cells subtract; componendo-dividendo gives the ratio.
Exam Note: Ratio E1 : E2 = 2 : 1.
Question Example 94. In the following circuit the potential difference between the points B and C is balanced against 40 cm length of potentiometer wire. In order to balance the potential difference between the points C and D, where should jockey be pressed (a) 32 cm (b) 16 cm (c) 8 cm (d) 4 cm. (Figure: potentiometer wire XY of which 40 cm is marked; a 6 V cell with two 10 Ω resistors in parallel between B and C, then 4 Ω between C and D, and a 1 Ω internal resistance with key K in series with the 6 V cell, points A and F at the bottom.)
Solution. (a). 1/R = 1/10 + 1/10 = 2/10 = 1/5 or R1 = 5 Ω. R2 = 4 Ω, l1 = 40 cm, l2 = ? l2 = l1(R2/R1) or l2 = (40 × 4)/5 = 32 cm.
Teacher's Note: Same current flows through BC and CD, so p.d. and balancing length are proportional to resistance.
Exam Note: Reduce the parallel 10 Ω pair to 5 Ω first.
Question Example 95. In the following circuit diagram fig. the lengths of the wires AB and BC are same but the radius of AB is three times that of BC. The ratio of potential gradients at AB and BC will be (a) 1 : 9 (b) 9 : 1 (c) 3 : 1 (d) 1 : 3. (Figure: a battery and rheostat in series with a potentiometer wire A-B-C made of two segments, AB thicker than BC.)
Solution. (a). x ∝ Rp ∝ 1/r2 ⇒ x1/x2 = r22/r12 = (r/3r)2 = 1/9.
Teacher's Note: Same current and length: potential gradient is proportional to resistance per length, i.e. 1/r2.
Exam Note: Thicker wire has the smaller gradient.
Question Example 96. With a certain cell the balance point is obtained at 0.60 m from one end of the potentiometer. With another cell whose emf differs from that of the first by 0.1 V, the balance point is obtained at 0.55 m. Then, the two emf's are (a) 1.2 V, 1.1 V (b) 1.2 V, 1.3 V (c) −1.1 V, −1.0 V (d) None of the above
Solution. (a). E1 = x(0.6) and E2 = E1 − 0.1 = x(0.55) ⇒ E1/(E1 − 0.1) = 0.6/0.55 or 55E1 = 60E1 − 6 ⇒ E1 = 6/5 = 1.2 V, thus E2 = 1.1 V.
Teacher's Note: Balancing length is proportional to emf, and the shorter length means the smaller emf.
Exam Note: Shorter length gives E2 = E1 − 0.1.
Question Tricky Example 11. [MP PMT 1985] A cell of internal resistance 1.5 Ω and of emf 1.5 volt balances 500 cm on a potentiometer wire. If a wire of 15 Ω is connected between the balance point and the cell, then the balance point will shift (a) To zero (b) By 500 cm (c) By 750 cm (d) None of the above
Solution. (d). In balance condition no current flows in the galvanometer circuit. Hence there will be no shift in balance point after connecting a resistance between balance point and cell.
Teacher's Note: At null point the cell draws no current, so extra series resistance causes no drop.
Exam Note: Zero current means no shift.
Free study material for Physics
Step-by-Step Pradeep's KL Gogia Solutions for Class 12 Math
Complete Math Solutions for Pradeep's KL Gogia Solutions Physics Chapter 2 Current Electricity Part 2
Review detailed solutions for Class 12 Mathematics. The Pradeep's KL Gogia Solutions Physics Chapter 2 Current Electricity Part 2 PDF provides comprehensive answers mapped to standard Pradeep's KL Gogia Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Concept-Driven Math Answers
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Next Steps in Your Mathematics Revision
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the Pradeep's KL Gogia book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.