Official Textbook Solutions: Class 12 Physics Chapter 07 Alternating Current
Explore reliable textbook solutions for Chapter 07 Alternating Current tailored for Class 12 learners using methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.
Chapter-wise Solutions for Physics: Chapter 07 Alternating Current
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Short Answer Questions II
Question 1. State the underlying principle of a transformer. How is the large scale transmission of electric energy over long distances done with the use of transformers? [CBSE (AI) 2012]
Solution.
The principle of transformer is based upon the principle of mutual induction which states that due to continuous change in the current in the primary coil an emf gets induced across the secondary coil. At the power generating station, the step up transformers step up the output voltage which reduces the current through the cables and hence reduce resistive power loss. Then, at the consumer end, a step down transformer steps down the voltage. Hence, the large scale transmission of electric energy over long distances is done by stepping up the voltage at the generating station to minimise the power loss in the transmission cables.
Teacher's Note: A transformer uses mutual induction, and step-up transmission reduces current and line loss.
Exam Note: Mention step-up and step-down.
Question 2. State the principle of working of a transformer. Can a transformer be used to step up or step down a d.c. voltage? Justify your answer. [CBSE (AI) 2011]
Solution.
Working of a transformer is based on the principle of mutual induction. Transformer cannot step up or step down a dc voltage.
Reason: No change in magnetic flux. Explanation: When dc voltage source is applied across a primary coil of a transformer, the current in primary coil remains same, so there is no change in magnetic flux associated with it and hence no voltage is induced across the secondary coil.
Teacher's Note: A transformer needs changing flux, which dc cannot provide.
Exam Note: Answer no; flux does not change.
Question 3. Show that the current leads the voltage in phase by π/2 in an ac circuit containing an ideal capacitor. [CBSE (F) 2014]
Solution.
The instantaneous voltage, V = V0 sin ωt … (i)
Let q be the charge on capacitor and I, the current in the circuit at any instant, then instantaneous potential difference, V = q/C … (ii)
From (i) and (ii): q/C = V0 sin ωt ⇒ q = CV0 sin ωt
The instantaneous current, I = dq/dt = CV0 d(sin ωt)/dt = CV0ω cos ωt
I = (V0/(1/ωC)) cos ωt
I = I0 sin(ωt + π/2)
Hence, the current leads the applied voltage in phase by π/2.
Teacher's Note: Differentiate q = C V to get i, then rewrite cosine as shifted sine.
Exam Note: Show I = I0 sin(omega t + pi/2).
Question 4. In a series LCR circuit, obtain the conditions under which (i) The impedance of the circuit is minimum, and (ii) Wattless current flows in the circuit. [CBSE (F) 2014]
Solution.
(i) Impedance of series LCR circuit is given by Z = √(R2 + (XL − XC)2)
For the impedance Z to be minimum, XL = XC.
(ii) Power P = VrmsIrms cos φ. When φ = π/2, power = VrmsIrms cos(π/2) = 0
Therefore, wattless current flows when the impedance of the circuit is purely inductive or purely capacitive.
In another way we can say, for wattless current to flow, circuit should not have any ohmic resistance (R = 0).
Teacher's Note: Minimum Z occurs at resonance; wattless current needs phase difference of 90 degrees.
Exam Note: State both conditions clearly.
Question 5. An electric lamp connected in series with a capacitor and an ac source is glowing with certain brightness. How does the brightness of the lamp change on reducing the (i) Capacitance and (ii) Frequency? [CBSE Delhi 2010, (North) 2016]
Solution.
(i) When capacitance is reduced, capacitive reactance XC = 1/ωC increases, hence impedance of circuit Z = √(R2 + XC2) increases and so current I = V/Z decreases. As a result the brightness of the bulb is reduced.
(ii) When frequency decreases; capacitive reactance XC = 1/2πνC increases and hence impedance of circuit increases, so current decreases. As a result brightness of bulb is reduced.
Teacher's Note: Both changes raise X_C, so impedance rises and current falls.
Exam Note: Chain: X_C up, Z up, I down.
Question 6. A resistor of 100 Ω and a capacitor of 100/π μF are connected in series to a 220 V, 50 Hz a.c. supply. (i) Calculate the current in the circuit. (ii) Calculate the (rms) voltage across the resistor and the capacitor. Do you find the algebraic sum of these voltages more than the source voltage? If yes, how do you resolve the paradox? [CBSE Chennai 2015]
Solution.
(i) Capacitive reactance XC = 1/ωC = 1/2πνC = 1/(2π × 50 × (100/π) μF) = 100 Ω
Impedance of the circuit, Z = √(R2 + XC2) = √(1002 + 1002) = 100√2 Ω
Current in the circuit Irms = Erms/Z = 220/(100√2) = 1.55 A
(ii) Voltage across resistor, VR = IrmsR = 1.55 × 100 = 155 V. Voltage across capacitor, VC = Irms × XC = 1.55 × 100 = 155 V
The algebraic sum of voltages across the combination is Vrms = VR + VC = 155 V + 155 V = 310 V, while Vrms of the source is 220 V. Yes, the voltages across the combination is more than the voltage of the source. The voltage across the resistor and capacitor are not in phase.
This paradox can be resolved as when the current passes through the capacitor, it leads the voltage VC by phase π/2. So, voltage of the source can be given as Vrms = √(VR2 + VC2) = √(1552 + 1552) = 155√2 = 220 V
Teacher's Note: V_R and V_C are 90 degrees out of phase, so add them as vectors.
Exam Note: Resolve the paradox with phasor addition.
Question 7. A capacitor of unknown capacitance, a resistor of 100 Ω and an inductor of self-inductance L = 4/π2 henry are connected in series to an ac source of 200 V and 50 Hz. Calculate the value of the capacitance and impedance of the circuit when the current is in phase with the voltage. Calculate the power dissipated in the circuit. [CBSE South 2016]
Solution.
Capacitance, C = 1/Lω2 = 1/((4/π2)(2π × 50)2) F = 1/40000 F = 2.5 × 10−5 F
Since V and I are in same phase, impedance = resistance = 100 Ω
Power dissipated = Erms2/R = (200)2/100 W = 400 W
Teacher's Note: In phase means resonance, so Z equals R and X_L equals X_C.
Exam Note: Use C = 1/(L omega squared).
Question 8. The figure shows a series LCR circuit with L = 5.0 H, C = 80 μF, R = 40 Ω connected to a variable frequency 240 V source. Calculate (i) The angular frequency of the source which drives the circuit at resonance. (ii) The current at the resonating frequency. (iii) The rms potential drop across the capacitor at resonance. [CBSE Delhi 2012]
Solution.
(i) ωr = Angular frequency at resonance = 1/√(LC) = 1/√(5 × 80 × 10−6) = 50 rad/s
(ii) Current at resonance, Irms = Vrms/R = 240/40 = 6 A
(iii) Vrms across capacitor = IrmsXC = 6 × 1/(50 × 80 × 10−6) = 6 × 106/(4 × 103) = 1500 V
Teacher's Note: At resonance Z equals R; capacitor voltage is I times X_C.
Exam Note: Compute omega_r first, then I, then V_C.
Question 9. (i) Find the value of the phase difference between the current and the voltage in the series LCR circuit shown below. Which one leads in phase: current or voltage? (ii) Without making any other change, find the value of the additional capacitor, C1, to be connected in parallel with the capacitor C, in order to make the power factor of the circuit unity. [CBSE Delhi 2017]
Solution.
(i) Inductive reactance, XL = ωL = (1000 × 100 × 10−3) Ω = 100 Ω
Capacitive reactance, XC = 1/ωC = 1/(1000 × 2 × 10−6) Ω = 500 Ω
Phase angle, tan φ = (XL − XC)/R = (100 − 500)/400 = −1
φ = −π/4. As XC > XL (phase angle is negative), hence current leads voltage.
(ii) To make power factor unity, XC' = XL (where C' = net capacitance of parallel combination): 1/ωC' = 100 ⇒ C' = 10 × 10−6 F = 10 μF
Since C' = C + C1: 10 = 2 + C1 ⇒ C1 = 8 μF
Teacher's Note: Negative phase angle shows capacitive circuit; add capacitance until X_C equals X_L.
Exam Note: Parallel capacitances add: C' = C + C1.
Question 10. (i) For a given ac, i = im sin ωt, show that the average power dissipated in a resistor R over a complete cycle is (1/2)im2R. (ii) A light bulb is rated at 100 W for a 220 V ac supply. Calculate the resistance of the bulb. [CBSE (AI) 2013]
Solution.
(i) Average power consumed in resistor R over a complete cycle:
Pav = (1/∫0Tdt)·∫0Ti2R dt = (im2R/T)∫0Tsin2ωt dt … (i)
= (im2R/2T)∫0T(1 − cos 2ωt)dt = (im2R/2T)[∫0Tdt − ∫0Tcos 2ωt dt] … (ii)
= (im2R/2T)[T − 0] = im2R/2
(ii) In case of ac, Pav = Vrms2/R = Veff2/R
R = Vrms2/P = (220 × 220)/100 = 484 Ω
Teacher's Note: The mean of cos 2 omega t over a cycle is zero, leaving half of i_m squared.
Exam Note: Use R = V_rms squared / P for the bulb.
Question 11. Determine the current and quality factor at resonance for a series LCR circuit with L = 1.00 mH, C = 1.00 nF and R = 100 Ω connected to an ac source having peak voltage of 100 V. [CBSE (F) 2011]
Solution.
Given L = 1.00 mH = 1 × 10−3 H, C = 1.00 nF = 1 × 10−9 F, R = 100 Ω, E0 = 100 V
I0 = E0/√(R2 + (ωL − 1/ωC)2) = E0/Z. At resonance ωL = 1/ωC, hence Z = R
∴ I0 = V/R = 100/100 = 1 A
Iv = I0/√2 = (1/√2) = 0.707 A
Q = (1/R)√(L/C) = (1/100)√(1.0 × 10−3/1.0 × 10−9) = (1/100) × 103 = 10
Teacher's Note: At resonance Z equals R, so peak current is E0/R.
Exam Note: rms current is I0/root 2; Q = 10.
Question 12. A circuit is set up by connecting inductance L = 100 mH, resistor R = 100 Ω and a capacitor of reactance 200 Ω in series. An alternating emf of 150√2 V, 500/π Hz is applied across this series combination. Calculate the power dissipated in the resistor. [CBSE (F) 2014]
Solution.
Here, L = 100 × 10−3 H, R = 100 Ω, XC = 200 Ω, Vrms = 150√2 V, ν = 500/π Hz
Inductive reactance XL = ωL = 2πνL = 2π × (500/π) × 100 × 10−3 = 100 Ω
Impedance of circuit Z = √(R2 + (XC − XL)2) = √(1002 + (200 − 100)2) = √20000 = 100√2 Ω
Irms = Vrms/Z = 150√2/(100√2) = 3/2 A
Power dissipated = (Irms)2R = (9/4) × 100 = 225 W
Teacher's Note: Power is dissipated only in the resistor: I_rms squared times R.
Exam Note: Find X_L first, then Z, then I.
Question 13. (a) Determine the value of phase difference between the current and the voltage in the given series LCR circuit. (b) Calculate the value of the additional capacitor which may be joined suitably to the capacitor C that would make the power factor of the circuit unity. [CBSE Allahabad 2015]
Solution.
(a) Phase angle, tan φ = (XL − XC)/R. XL = ωL = 1000 × 100 × 10−3 = 100 ohm; XC = 1/ωC = 1/(1000 × 2 × 10−6) = 1000/2 = 500 ohm
∴ tan φ' = (500 − 100)/400 = 1 ⇒ φ' = 45°. The phase angle between the current and applied voltage is 45° (= π/4).
(b) If power factor of the circuit is unity, the series LCR would be in resonance. So, XC' = XL ⇒ 1/ωC' = ωL ⇒ C' = 1/ω2L = 1/((1000)2 × 100 × 10−3) = 10−5 F ⇒ C' = 10 μF
Since C' > C, so an additional capacitor of 8 μF would be connected in parallel with the capacitor of C = 2 μF.
Teacher's Note: Net capacitance must make X_C equal X_L; add the difference in parallel.
Exam Note: Answer: 45 degrees; extra 8 microfarad in parallel.
Question 14. The primary coil of an ideal step up transformer has 100 turns and transformation ratio is also 100. The input voltage and power are 220 V and 1100 W respectively. Calculate (a) The number of turns in the secondary coil. (b) The current in the primary coil. (c) The voltage across the secondary coil. (d) The current in the secondary coil. (e) The power in the secondary coil. [CBSE Delhi 2016]
Solution.
(a) Transformation ratio r = NS/NP. Given NP = 100, r = 100 ∴ NS = rNP = 100 × 100 = 10,000
(b) Input voltage VP = 220 V, input power Pin = 1100 W. Current in primary coil IP = Pin/VP = 1100/220 = 5 A
(c) r = VS/VP ⇒ VS = rVP = 100 × 220 = 22,000 V = 22 kV
(d) r = IP/IS ⇒ IS = IP/r = 5/100 = 0.05 A
(e) Power in secondary coil, Pout = VSIS = 22 × 103 × 0.05 = 1100 W
Obviously power in secondary coil is same as power in primary. This means that the transformer is ideal, i.e. there are no energy losses.
Teacher's Note: Step-up multiplies voltage by r and divides current by r.
Exam Note: Power in equals power out for ideal transformer.
Question 15. An inductor L of reactance XL is connected in series with a bulb B to an ac source as shown in figure. Explain briefly how does the brightness of the bulb change when (i) number of turns of the inductor is reduced (ii) an iron rod is inserted in the inductor and (iii) a capacitor of reactance XC = XL is included in the circuit. [CBSE Delhi 2014, 2015]
Solution.
Brightness of the bulb depends on square of the Irms (i.e., Irms2). Impedance of the circuit, Z = √(R2 + (ωL)2) and current in the circuit, I = V/Z.
(i) When the number of turns in the inductor is reduced, the self-inductance of the coil decreases; so impedance of the circuit reduces and so current in the circuit (I = E/Z) increases. Thus the brightness of the bulb increases.
(ii) When iron (being a ferromagnetic substance) rod is inserted in the coil, its inductance increases and in turn, impedance of the circuit increases. As a result, a larger fraction of the applied ac voltage appears across the inductor, leaving less voltage across the bulb. Hence, brightness of the bulb decreases.
(iii) When capacitor of reactance XC = XL is introduced, the net reactance of circuit becomes zero, so impedance of circuit decreases; it becomes Z = R; so current in circuit increases; hence brightness of bulb increases. Thus brightness of bulb in both cases increases.
Teacher's Note: Brightness follows I squared; check how each change alters impedance.
Exam Note: Cases (i) and (iii) brighten; (ii) dims.
Question 16. You are given three circuit elements X, Y and Z. When the element X is connected across an a.c. source of a given voltage, the current and the voltage are in the same phase. When the element Y is connected in series with X across the source, voltage is ahead of the current in phase by π/4. But the current is ahead of the voltage in phase by π/4 when Z is connected in series with X across the source. Identify the circuit elements X, Y and Z. When all the three elements are connected in series across the same source, determine the impedance of the circuit. Draw a plot of the current versus the frequency of applied source and mention the significance of this plot. [CBSE Panchkula 2015]
Solution.
Since the phase angle between the current Ieff and voltage drop Veff is zero, the element X is a resistor.
The voltage drop across the combination X and Y is ahead of the current flow. Hence, the element Y is an inductor.
The voltage drop across the combination X and Z lags behind the current flow. Hence, the element Z is a capacitor.
Let Ieff be the current through each element X, Y and Z. The voltages VX, VY and VZ drop across the elements. However, VX + VY + VZ > Eeff. It is not possible. So, on plotting phasor diagram, we have |Eeff|2 = VR2 + (VL − VC)2 … (1)
Eeff = Ieff√(R2 + (XL − XC)2). Since Eeff = IeffZ … (2), the impedance of the circuit is Z = √(R2 + (XL − XC)2).
The flow of the current in series LCR circuit varies as a function of frequency of a.c. source is shown in figure.
Current amplitude is maximum at resonant frequency ω0 and is Imax = Veff/R. It is possible at Z = R (or ω0 = 1/√(LC)).
Significance: The resonance phenomenon is exhibited by the circuit only when both L and C are present in the circuit. When voltages across L and C cancel each other (on being out of phase), the current in the circuit reaches its maximum value Veff/R. So, we cannot have resonance in a R-L or R-C circuits.
Teacher's Note: Phase shifts identify X as R, Y as L and Z as C.
Exam Note: Give Z formula; sketch resonance curve with peak at omega_0.
Question 17. Given below are two electrical circuits A and B. Calculate the ratio of power factor of circuit B to the power factor of circuit A.
Solution.
Power factor, cos φ = R/Z. Impedance of circuit A, ZA = √(R2 + XL2) = √(R2 + (3R)2) = √10 R
Impedance of circuit B, ZB = √(R2 + (XL − XC)2) = √(R2 + (3R − R)2) = √5 R
Ratio of power factor of circuit B to that of A: (cos φ)B/(cos φ)A = (R/ZB)/(R/ZA) = ZA/ZB = √10/√5 = √2
Teacher's Note: Power factor is R over Z; the common R cancels in the ratio.
Exam Note: Answer: root 2.
Question 18. Prove that the power dissipated in an ideal resistor connected to an ac source is Veff2/R.
Solution.
Power in ac circuit, P = Vrmsirms cos φ. As rms values of current and voltage are also called effective values i.e. P = VeffIeff cos φ … (i)
But cos φ = power factor = R/Z. In a purely resistive circuit Z = R, cos φ = 1, and ieff = Veff/Z = Veff/R
Substituting these values in (i), we get P = Veff · (Veff/R) × 1 = Veff2/R.
Teacher's Note: For a pure resistor phi is zero and the effective current is V over R.
Exam Note: Substitute I_eff = V_eff/R in P = V I cos phi.
Question 19. An inductor 200 mH, a capacitor 100 μF and a resistor 10 Ω are connected in series to an a.c. source of 100 V, having variable frequency. (i) At what frequency of the applied voltage will the power factor of the circuit be 1? (ii) What will be the current amplitude at this frequency? (iii) Calculate the Q-factor of the circuit.
Solution.
(i) Since the power factor cos φ = 1, the phase difference between voltage and the current is zero. This is possible when ωL = 1/ωC, ω2 = 1/LC ⇒ ν = 1/(2π√(LC)) ≈ 35.6 Hz
(ii) Current amplitude, I = Veff/Z = Veff/R = 100/10 = 10 A (∵ Z = R)
(iii) Quality factor, Q = (1/R)√(L/C) = (1/10)√(0.2/(100 × 10−6)) = 4.47
Teacher's Note: Unity power factor means resonance, so Z equals R.
Exam Note: Use nu = 1/(2 pi root LC) and Q = (1/R) root(L/C).
Question 20. An AC voltage V = Vm is applied across a: (i) Series RC circuit in which capacitive reactance is ‘a’ times the resistance in the circuit. (ii) Series RL circuit in which inductive reactance is ‘b’ times the resistance in the circuit. Find the value of power factor of the circuit in each case.
Solution.
Power factor cos φ = R/Z, when Z = √(R2 + X2)
(i) X = XC = aR, ∴ Z = √(R2 + (aR)2) = R√(1 + a2), ∴ cos φ = R/(R√(1 + a2)) = 1/√(1 + a2)
(ii) X = XL = bR, ∴ Z = √(R2 + (bR)2) = R√(1 + b2), ∴ cos φ = R/(R√(1 + b2)) = 1/√(1 + b2)
Teacher's Note: Substitute the reactance as a multiple of R into R over Z.
Exam Note: Answers: 1/root(1+a^2) and 1/root(1+b^2).
Question 21. Figure shows a light bulb (B) and iron cored inductor connected to a dc battery through a switch (S). (i) What will one observe when switch (S) is closed? (ii) How will the glow of the bulb change when the battery is replaced by an ac source of rms voltage equal to the voltage of dc battery? Justify your answer in each case.
Solution.
(i) When switch S is closed, the bulb will give full brightness slowly, because inductor opposes the rise of current in the circuit depending on the value of ratio L/R (L = inductance, R = resistance of bulb).
(ii) When battery is replaced by an ac source, the inductor offers reactance (ωL) so impedance of circuit increases and the bulb will glow with less brightness.
Teacher's Note: Inductor delays growth under dc; under ac it adds reactance.
Exam Note: Time constant L/R; ac impedance reduces glow.
Question 22. In the circuit shown below R represents an electric bulb. If the frequency ν = (ω/2π) of the supply is doubled, how should the values of C and L be changed, so that the glow of bulb remains unchanged?
Solution.
For same current value, the total impedance √(R2 + (ωL − 1/ωC)2) must remain same.
Therefore, ωL − 1/ωC must remain same. As frequency (ω) is doubled, L and C must both be halved simultaneously.
Teacher's Note: Unchanged glow means unchanged impedance, so omega L and 1/(omega C) must stay fixed.
Exam Note: Double omega: halve both L and C.
Question 23. When a circuit element ‘X’ is connected across an a.c. source, a current of √2 A flows through it and this current is in phase with the applied emf. When another element ‘Y’ is connected across the same a.c. source, the same current flows in the circuit but it leads the voltage by π/2 radians. (i) Name the circuit element X and Y. (ii) Find the current that flows in the circuit when the series combination of X and Y is connected across the same a.c. voltage. (iii) Net impedance.
Solution.
(i) When circuit element is X, the current is in phase with the applied emf, this implies that X is pure resistance. When circuit element Y is connected, the current leads the voltage by π/2 so Y is pure capacitance.
(ii) Resistance of X = R; I = V/R or √2 = V/R … (i). Reactance of Y, XC = 1/ωC, I = V/XC ⇒ √2 = V/XC … (ii). This implies XC = R.
When R and C are connected in series across same voltage source, then impedance Z = √(R2 + XC2) = √(R2 + R2) = √2 R … (iii)
∴ Current in circuit I = V/Z = V/(√2 R). From (i), V/R = √2, ∴ I = (1/√2) × √2 = 1 A
(iii) Z = √(R2 + (1/ωC)2), i.e., impedance decreases with increase of angular frequency ω. When ω = 0, Z = ∞. When ω = ∞, Z = R. The graph of impedance Z versus ω is shown in fig.
Teacher's Note: Current in phase means resistor; current leading by 90 degrees means capacitor.
Exam Note: Equal currents imply X_C = R, so Z = root 2 R.
Question 24. A device ‘X’ is connected to an a.c. source. The variation of voltage, current and power in one complete cycle is shown in the figure. (i) Which curve shows power consumption over a full cycle? (ii) What is the average power consumption over a cycle? (iii) Identify the device ‘X’. [NCERT Exemplar]
Solution.
(i) A
(ii) Zero
(iii) L or C or LC
Teacher's Note: Power varies at double frequency and averages to zero in reactive devices.
Exam Note: Zero average power means a purely reactive device.
Question 25. (i) Draw the graphs showing variation of inductive reactance and capacitive reactance with frequency of applied a.c. source. (ii) Can the voltage drop across the inductor or the capacitor in a series LCR circuit be greater than the applied voltage of the a.c. source? Justify your answer.
Solution.
(i) (a) XL = ωL = 2πνL; graph XL of f and f is a straight line. (b) XC = 1/ωC = 1/2πνC; graph of XC and f is a rectangular hyperbola as shown in figs.
(ii) Yes; because as VC and VL have opposite phases, VC or VL may be greater than V. The situation may be as shown in figure where VC > V.
Teacher's Note: V_L and V_C are opposite in phase, so their difference can leave either larger than V.
Exam Note: Graph: X_L is a line, X_C a hyperbola.
Free study material for Physics
Download Xam Idea Solutions for Class 12 Math PDF
Access Class 12 Mathematics Solutions
Review detailed solutions for Class 12 Mathematics. The Xam Idea Solutions Class 12 Physics Chapter 7 Alternating Current Short Answer Questions II PDF provides comprehensive answers mapped to standard Xam Idea Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Concept-Driven Math Answers
Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.
Complete Your Class 12 Exam Preparation
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.