Solutions for Class 12 Physics: Chapter 07 Alternating Current
Review structured textbook solutions for Class 12 Physics Chapter 07 Alternating Current prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Practice Class 12 Physics Solutions: Chapter 07 Alternating Current
Access the complete solution PDF for Class 12 Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Short Answer Questions I
Question 1. In India, Domestic power supply is at 220 V, 50 Hz; while in USA it is 110 V, 50 Hz. Give one advantage and one disadvantage of 220 V supply over 110 V supply.
Solution.
Advantage: Line loss is low.
Disadvantage: High voltage is dangerous.
Teacher's Note: Higher voltage means lower current and line loss, but greater danger.
Exam Note: One advantage, one disadvantage.
Question 2. Both alternating current and direct current are measured in amperes. But how is the ampere defined for an alternating current? [NCERT Exemplar]
Solution.
An ac current changes direction with the source frequency and the attractive force would average to zero. Thus, the ac ampere must be defined in terms of some property that is independent of the direction of current. Joule’s heating effect is such property and hence it is used to define rms value of ac.
Teacher's Note: The ac ampere is defined by heating effect, because magnetic force averages to zero.
Exam Note: Mention rms value, heating effect.
Question 3. Explain why the reactance provided by a capacitor to an alternating current decreases with increasing frequency. [NCERT Exemplar]
Solution.
A capacitor does not allow flow of direct current through it as the resistance across the gap is infinite. When an alternating voltage is applied across the capacitor plates, the plates are alternately charged and discharged. The current through the capacitor is a result of this changing voltage (or charge). Thus, a capacitor will pass more current through it if the voltage is changing at a faster rate, i.e., if the frequency of supply is higher. This implies that the reactance offered by a capacitor is less with increasing frequency; it is given by 1/ωC.
Teacher's Note: Capacitive reactance is inversely proportional to frequency, so it falls as frequency rises.
Exam Note: Write Xc = 1/(2 pi f C).
Question 4. Explain why the reactance offered by an inductor increases with increasing frequency of an alternating voltage. [NCERT Exemplar]
Solution.
An inductor opposes flow of current through it by developing an induced emf according to Lenz’s law. The induced voltage has a polarity so as to maintain the current at its present value. If the current is decreasing, the polarity of the induced emf will be so as to increase the current and vice versa. Since the induced emf is proportional to the rate of change of current, it will provide greater reactance to the flow of current if the rate of change is faster, i.e., if the frequency is higher. The reactance of an inductor, therefore, is proportional to the frequency, being given by ωL.
Teacher's Note: Faster current changes at higher frequency produce larger opposing emf, so inductive reactance rises.
Exam Note: Write XL = 2 pi f L.
Question 5. Define power factor. State the conditions under which it is (i) maximum and (ii) minimum. [CBSE Delhi 2010]
Solution.
The power factor (cos φ) is the ratio of resistance and impedance of an ac circuit i.e., cos φ = R/Z.
Maximum power factor is 1 when Z = R i.e., when circuit is purely resistive. Minimum power factor is 0 when R = 0 i.e., when circuit is purely inductive or capacitive.
Teacher's Note: Power factor is R/Z, between 0 and 1.
Exam Note: Give both limiting cases with R and Z.
Question 6. When an AC source is connected to an ideal inductor show that the average power supplied by the source over a complete cycle is zero. [CBSE (Central) 2016]
Solution.
For an ideal inductor phase difference between current and applied voltage = π/2
∴ Power, P = VrmsIrms cos φ = VrmsIrms cos(π/2) = 0.
Thus the power consumed in a pure inductor is zero.
Teacher's Note: Current lags voltage by 90 degrees, so cos phi is zero.
Exam Note: Use P = V_rms I_rms cos phi.
Question 7. When an AC source is connected to an ideal capacitor, show that the average power supplied by the source over a complete cycle is zero. [CBSE (North) 2016]
Solution.
Power dissipated in ac circuit, P = VrmsIrms cos φ where cos φ = R/Z
For an ideal capacitor R = 0 ∴ cos φ = R/Z = 0
∴ P = VrmsIrms cos φ = VrmsIrms × 0 = 0 (zero).
i.e., power dissipated in an ideal capacitor is zero.
Teacher's Note: Ideal capacitor has no resistance, so no power is dissipated.
Exam Note: Set R = 0 in cos phi = R/Z.
Question 8. The current flowing through a pure inductor of inductance 2 mH is i = 15 cos 300t ampere. What is the (i) rms and (ii) average value of current for a complete cycle? [CBSE (F) 2011]
Solution.
Peak value of current (i0) = 15 A
(i) irms = i0/√2 = 15/√2 = (15/√2) × (√2/√2) = 7.5√2 A
(ii) iav = 0
Teacher's Note: Average over a full cycle of a sinusoid is zero.
Exam Note: rms = peak divided by root 2.
Question 9. In a series LCR circuit with an ac source of effective voltage 50 V, frequency ν = 50/π Hz, R = 300 Ω, C = 20 μF and L = 1.0 H. Find the rms current in the circuit. [CBSE (F) 2014]
Solution.
Given L = 1.0 H; C = 20 μF = 20 × 10−6 F; R = 300 Ω; Vrms = 50 V; ν = 50/π Hz
Inductive reactance XL = ωL = 2πνL = 2 × π × (50/π) × 1 = 100 Ω
Capacitive reactance, XC = 1/ωC = 1/(2πνC) = 1/(2 × π × (50/π) × 20 × 10−6) = 500 Ω
Impedance Z = √(R2 + (XC − XL)2) = √(3002 + (500 − 100)2) = √(90000 + 160000) = √250000 = 500 Ω
Irms = Vrms/Z = 50/500 = 0.1 A
Teacher's Note: Find X_L and X_C first, then impedance, then current.
Exam Note: Answer: 0.1 A.
Question 10. Calculate the quality factor of a series LCR circuit with L = 2.0 H, C = 2 μF and R = 10 Ω. Mention the significance of quality factor in LCR circuit. [CBSE (F) 2012]
Solution.
We have, Q = (1/R)√(L/C) = (1/10)√(2/(2 × 10−6)) = (1/10) × 1000 = 100
It signifies the sharpness of resonance.
Teacher's Note: Q = (1/R) root(L/C); higher Q means sharper resonance.
Exam Note: Quote the significance with the value.
Question 11. The instantaneous current in an ac circuit is i = 0.5 sin 314 t, what is (i) rms value and (ii) frequency of the current.
Solution.
Given I = 0.5 sin 314 t … (i); standard equation of current is I = I0 sin ωt … (ii)
Comparing (i) and (ii), we get I0 = 0.5 A, ω = 314
∴ (i) rms value Irms = I0/√2 = 0.5/√2 A = 0.35 A
(ii) Frequency ν = ω/2π = 314/(2 × 3.14) = 50 Hz
Teacher's Note: Compare with I0 sin(omega t) to read off peak and omega.
Exam Note: rms = peak/root 2; frequency = omega/2pi.
Question 12. The instantaneous voltage from an ac source is given by E = 300 sin 314t; what is the rms voltage of the source.
Solution.
Given equation is E = 300 sin 314 t. Comparing with standard equation E = E0 sin ωt, we have E0 = 300 volt
So Erms = E0/√2 = 300/√2 = 150√2 volt = 150 × 1.414 = 212 V
Teacher's Note: Peak voltage is 300 V; divide by root 2.
Exam Note: Answer: about 212 V.
Question 13. In the given circuit, the potential difference across the inductor L and resistor R are 200 V and 150 V respectively and the rms. value of current is 5 A. Calculate (i) the impedance of the circuit and (ii) the phase angle between the voltage and the current.
Solution.
Voltage applied V = √(VL2 + VR2) = √(2002 + 1502) = 250 V
Impedance of circuit, Z = V/I = 250/5 = 50 Ω
Phase angle between voltage and current: tan φ = XL/R = VL/VR = 200/150 = 4/3
φ = tan−1(4/3) = 53°
Teacher's Note: V_L and V_R are 90 degrees apart, so add them in quadrature.
Exam Note: Z = V/I; tan phi = V_L/V_R.
Question 14. An AC source of voltage V = Vm sin ωt is applied across a series LCR circuit. Draw the phasor diagrams for this circuit, when (i) Capacitive impedance exceeds the inductive impedance. (ii) Inductive impedance exceeds capacitive impedance.
Solution.
(i) When XC > XL; the phasor diagram is shown in fig. (a).
(ii) When XL > XC; the phasor diagram is shown in fig. (b).
Teacher's Note: Draw V_R along current; V_L up and V_C down; add the difference.
Exam Note: Label phi and the net reactive phasor.
Question 15. In a series LCR circuit, R = 1kΩ, C = 2μF and voltage across R is 100 V. The resonant frequency of the circuit ω is 200 rad s−1. Calculate the value of voltage across L at resonance.
Solution.
Current flowing in the circuit is I = VR/R = 100/1000 = 0.1 A
∴ Also at resonance, ωL = 1/ωC
ωL = 1/(200 × 2 × 10−6) = 2500 Ω
∴ Voltage across L = I(ωL) = 0.1 × 2500 = 250 V
Teacher's Note: At resonance X_L equals X_C, which gives omega L.
Exam Note: Voltage across L is I times X_L.
Question 16. What is the power dissipated in an ac circuit in which voltage and current are given by V = 230 sin(ωt + π/2) and I = 10 sin ωt?
Solution.
Power dissipated P = (1/2)V0I0 cos φ
Here V0 = 230 V, I0 = 10 A, φ = π/2
∴ P = (1/2) × 230 × 10 cos(π/2) = 0.
Teacher's Note: Phase difference is 90 degrees, so no power is dissipated.
Exam Note: Zero power: purely reactive circuit.
Question 17. Calculate the following: (i) Impedance of the given ac circuit. (ii) Wattless current of the given ac circuit.
Solution.
(i) Potential difference across capacitance, VC = XCI ∴ capacitive reactance XC = VC/I = 40/2 = 20 Ω
Resistance, R = VR/I = 30/2 = 15 Ω
Impedance, Z = √(R2 + XC2) = √(152 + 202) = √625 = 25 Ω
(ii) The phase lead (φ) of current over applied voltage: tan φ = XC/R
Wattless current, Iwattless = I sin φ = I(XC/Z) = 2 × 20/25 A = 1.6 A
Teacher's Note: Find X_C and R from the given voltages and current.
Exam Note: Wattless current = I sin phi.
Question 18. In the given diagram, a coil B is connected to low voltage bulb L and placed parallel to another coil A as shown. Explain the following observations: (i) Bulb lights and (ii) Bulb gets dimmer if the coil B moves upwards.
Solution.
(i) Bulb lights up due to induced current in B because of change in flux linked with it as a consequence of continuous variation of magnitude of alternative current flowing in A.
(ii) When coil B moves upward, the magnetic flux linked with B decreases and hence lesser current is induced in B.
Teacher's Note: Changing current in A changes flux through B, inducing emf.
Exam Note: Link flux change to induced current.
Question 19. In a series LCR circuit, the voltage across an inductor, a capacitor and a resistor are 30 V, 30 V and 60 V respectively. What is the phase difference between the applied voltage and current in the circuit?
Solution.
Given VL = 30 V, VC = 30 V, VR = 60 V
Phase difference (φ) in series LCR circuit is given by tan φ = (XC − XL)/R = (VC − VL)/VR = (30 − 30)/60 = 0
⇒ φ = 0 (zero)
Teacher's Note: Equal V_L and V_C cancel, so the circuit is resonant.
Exam Note: Answer: phase difference is zero.
Question 20. When a capacitor is connected in series LR circuit, the alternating current flowing in the circuit increases. Explain why.
Solution.
Impedance of series LR circuit Z1 = √(R2 + XL2)
When capacitor is also connected in circuit, then impedance Z2 = √(R2 + (XL − XC)2)
Clearly impedance of circuit decreases (Z2 < Z1), so the value of current I = V/Z ∝ 1/Z in the circuit increases.
Teacher's Note: Capacitive reactance opposes inductive reactance, so net reactance shrinks.
Exam Note: Show Z falls, hence I = V/Z rises.
Question 21. Distinguish between the terms ‘effective value’ and peak value of alternating current.
Solution.
Alternating current changes in magnitude as well as direction. The maximum value of the alternating current is called the peak value. It is denoted by I0. The square root of mean square value of current is called the ‘effective value’ or ‘rms value’ of current. The two are related by
Effective value, Eeff = I0/√2
Teacher's Note: Effective value is the dc equivalent giving the same heating.
Exam Note: Quote I_eff = I_0/root 2.
Question 22. What is the power dissipated by an ideal inductor in ac circuit? Explain.
Solution.
The power P = VrmsIrms cos φ
An ideal inductor is the one whose resistive component is zero.
where cos φ = R/Z; for ideal inductor R = 0, ∴ cos φ = R/Z = 0
∴ P = VrmsIrms cos φ = 0, i.e., power dissipated by an ideal inductor in ac circuit is zero.
Teacher's Note: Zero resistance gives zero power factor and no heating.
Exam Note: Use P = V I cos phi with R = 0.
Question 23. A 60W load is connected to the secondary of a transformer whose primary draws line voltage. If a current of 0.54 A flows in the load, what is the current in the primary coil? Comment on the type of transformer being used. [NCERT Exemplar]
Solution.
Here PL = 60 W, IL = 0.54 A
VL = 60/0.54 ≈ 110 V
The transformer is step-down and have 1/2 input voltage. Hence ip = (1/2) × IL = (1/2) × 0.54 = 0.27 A.
Teacher's Note: Secondary voltage is half the line voltage, so primary current is half.
Exam Note: Say step-down; primary current 0.27 A.
Question 24. In the given circuit, the value of resistance effect of the coil L is exactly equal to the resistance R. Bulbs B1 and B2 are exactly identical. (i) Which one of the two bulbs lights up earlier, when key K is closed and why? (ii) What will be the comparative brightness of the two bulbs after sometime if the key K is kept closed and why?
Solution.
(i) Bulb B2 lights up earlier. The self-induction effect due to coil L in bulb B1 arm does not allow the current to attain maximum value immediately on closing the circuit.
(ii) Since the resistance effect of the coil L is equal to R and the self-induction effect in coil L will disappear after sometime, the current in both the arms will be equal. Hence, both the bulbs will glow with equal brightness after sometime.
Teacher's Note: Back emf in L delays current growth in the B1 branch.
Exam Note: Compare initial and steady-state currents.
Free study material for Physics
Class 12 Mathematics: Xam Idea Solutions for Xam Idea Solutions Class 12 Physics Chapter 7 Alternating Current Short Answer Questions I
Download Xam Idea Solutions for Class 12
Review detailed solutions for Class 12 Mathematics. The Xam Idea Solutions Class 12 Physics Chapter 7 Alternating Current Short Answer Questions I PDF provides comprehensive answers mapped to standard Xam Idea Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Step-by-Step Mathematical Explanations
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Complete Your Class 12 Exam Preparation
Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.