Step-by-Step Solutions for Class 12 Physics Chapter 06 Electromagnetic Induction
Review structured textbook solutions for Class 12 Physics Chapter 06 Electromagnetic Induction prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Download Chapter 06 Electromagnetic Induction Textbook Solutions PDF
Access the complete solution PDF for Class 12 Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Short Answer Questions I
Question 1. State Lenz’s Law.
A metallic rod held horizontally along east-west direction, is allowed to fall under gravity. Will there be an emf induced at its ends? Justify your answer. [CBSE Delhi 2013]
Solution.
Lenz’s law: According to this law “the direction of induced current in a closed circuit is always such as to oppose the cause that produces it.”
The direction of induced current in a circuit is such that it opposes the very cause which generates it.
Yes, an emf will be induced at its ends.
Justification: As the rod falls, it cuts the horizontal component of Earth’s magnetic field (directed north-south), which is perpendicular to both the rod (east-west) and its velocity (vertical). So the flux swept by the rod keeps changing and an emf ε = BHlv is induced across its ends.
Teacher's Note: A falling east-west rod cuts the horizontal component of Earth's field, which is perpendicular to both rod and velocity.
Exam Note: State Lenz's law; say yes, horizontal component.
Question 2. When a bar magnet is pushed towards (or away) from the coil connected to a galvanometer, the pointer in the galvanometer deflects. Identify the phenomenon causing this deflection and write the factors on which the amount and direction of the deflection depends. State the laws describing this phenomenon.
Solution.
The phenomenon involved is electromagnetic induction (EMI).
The amount of deflection depends upon the speed of movement of the magnet or rate of change of flux. Direction depends on the sense (towards, or away) of the movement of the magnet. Direction of deflection is according to Lenz’ law.
The law describing the phenomenon is:
Faraday’s law: The magnitude of the induced emf, in a circuit, is equal to the rate of change of the magnetic flux through the circuit, ε = –dφ/dt.
Lenz’s law: The direction of the induced current is such that it opposes the change in magnetic flux that produces it.
Teacher's Note: Pushing the magnet changes flux through the coil; speed sets the size, direction of motion sets the sign.
Exam Note: Name EMI; state Faraday's and Lenz's laws.
Question 3. The magnetic field through a circular loop of wire 12 cm in radius and 8.5 Ω resistance, changes with time as shown in the figure. The magnetic field is perpendicular to the plane of the loop. Calculate the induced current in the loop and plot it as a function of time. [CBSE (F) 2017]
Solution.
We know,
ε = –dφB/dt = –d(BA)/dt = –A dB/dt
I = ε/R = –A(dB/dt)/R
Here A = π(0.12)2 = 4.52 × 10–2 m2, R = 8.5 Ω.
For 0 < t < 2 s: dB/dt = (1 – 0)/2 = 0.5 T s–1
I = –(3.14 × (0.12)2 × 0.5)/8.5 = –0.00266 A ≈ –2.7 × 10–3 A (magnitude 2.66 mA)
For 2 < t < 4 s: dB/dt = 0 ⇒ I = 0
For 4 < t < 6 s: dB/dt = –0.5 T s–1, so I = +0.00266 A ≈ +2.7 × 10–3 A
(The negative sign for 0–2 s means the induced current opposes the increasing field; its sense is reversed for 4–6 s.)
Teacher's Note: Induced current is non-zero only while B changes: ±A(0.5 T/s)/R, zero while B is steady.
Exam Note: Get dB/dt for each interval before plotting.
Question 4. A rectangular conductor LMNO is placed in a uniform magnetic field of 0.5 T. The field is directed perpendicular to the plane of the conductor. When the arm MN of length of 20 cm is moved towards left with a velocity of 10 ms–1, calculate the emf induced in the arm. Given the resistance of the arm to be 5 Ω (assuming that other arms are of negligible resistance), find the value of the current in the arm. [CBSE (AI) 2013]
Solution.
Induced emf in a moving rod in a magnetic field is given by
ε = Blv (magnitude)
ε = Blv = 0.5 × 0.2 × 10 = 1 V
Current in the rod I = ε/R = 1/5 = 0.2 A
Teacher's Note: Motional emf is Blv with l = 0.20 m; current follows from Ohm's law with the arm's 5 ohm.
Exam Note: Convert 20 cm to metres; then I = e/R.
Question 5. A square loop MNOP of side 20 cm is placed horizontally in a uniform magnetic field acting vertically downwards as shown in the figure. The loop is pulled with a constant velocity of 20 cm s–1 till it goes out of the field.
(i) Depict the direction of the induced current in the loop as it goes out of the field. For how long would the current in the loop persist?
(ii) Plot a graph showing the variation of magnetic flux and induced emf as a function of time. [CBSE Panchkula 2015]
Solution.
(i)
While the loop leaves the field, the downward flux through it decreases, so by Lenz’s law the induced current produces a downward field inside the loop: it is clockwise (along MNOPM).
t = d/v = 20/20 = 1 s
Induced current will last for 1 second till the length 20 cm moves out of the field.
(ii) The loop moves 80 cm inside the field region without any flux change (4 s), and then leaves it in the next 1 s. During 0–4 s flux is constant (φ = BA = B × 0.04 Wb) and emf is zero; during 4–5 s the flux falls uniformly to zero and a constant emf Blv = B × 0.2 × 0.2 V acts.
Teacher's Note: Current flows only while the loop crosses the boundary: 0.2 m at 0.2 m/s gives 1 second.
Exam Note: Flux falls linearly over 1 s; emf is constant then.
Question 6. (i) When primary coil P is moved towards secondary coil S (as shown in the figure below) the galvanometer shows momentary deflection. What can be done to have larger deflection in the galvanometer with the same battery?
(ii) State the related law. [CBSE Delhi 2010]
Solution.
(i) For larger deflection, coil P should be moved at a faster rate.
(ii) Faraday law: The induced emf is directly proportional to rate of change of magnetic flux linked with the circuit.
Teacher's Note: A faster approach raises dφ/dt, so the induced emf and the galvanometer deflection both grow.
Exam Note: Move P faster; quote Faraday's law.
Question 7. A current is induced in coil C1 due to the motion of current carrying coil C2.
(ii) Suggest an alternative device to demonstrate the induced current in place of a galvanometer. [CBSE Delhi 2011]
Solution.
(1) The deflection in galvanometer may be made large by
(i) Moving coil C2 towards C1 with high speed.
(ii) By placing a soft iron laminated core at the centre of coil C1.
(2) The induced current can be demonstrated by connecting a torch bulb (in place of galvanometer) in Coil C1. Due to induced current the bulb begins to glow.
Teacher's Note: Faster motion and an iron core both increase flux change in C1; a bulb can replace G.
Exam Note: Give two ways; name the bulb.
Question 8. Answer the following questions
(i) Define mutual inductance.
(ii) A pair of adjacent coils has a mutual inductance of 1.5 H. If the current in one coil changes from 0 to 20 A in 0.5 s, what is the change of flux linkage with the other coil? [CBSE Delhi 2016]
Solution.
(i) Mutual inductance of two coils is numerically equal to the magnetic flux linked with one coil (secondary) when unit current flows through the other coil (primary). Equivalently, it is the emf induced in one coil when the current in the other changes at the rate of 1 A/s.
(ii) Change of flux for small change in current
dφ = M dI = 1.5 (20 – 0) weber = 30 weber
Teacher's Note: Flux linkage in the second coil changes by M times the change in current, independent of time taken.
Exam Note: Use dφ = M dI; the 0.5 s is not needed.
Question 9. A long solenoid with 15 turns per cm has a small loop of area 2.0 cm2 placed inside the solenoid normal to its axis. If the current carried by the solenoid changes steadily from 2.0 A to 4.0 A in 0.1 s, what is the induced emf in the loop while the current is changing? [CBSE (F) 2016]
Solution.
Mutual inductance of solenoid–coil system
M = μ0N1N2A2/l
Here N1 = 15, N2 = 1, l = 1 cm = 10–2 m, A2 = 2.0 cm2 = 2.0 × 10–4 m2
∴ M = (4π × 10–7 × 15 × 1 × 2.0 × 10–4)/10–2 = 120π × 10–9 H
Induced emf in the loop,
ε2 = M ΔI/Δt (numerically)
= 120π × 10–9 × (4 – 2)/0.1
= 120 × 3.14 × 10–9 × 2/0.1 = 7.5 × 10–6 V = 7.5 μV
Teacher's Note: Loop sees the solenoid field B = μ0 n I, so emf = μ0 n A (dI/dt) = 7.5 microvolt.
Exam Note: Convert 15 turns per cm to 1500 per m.
Question 10. A toroidal solenoid with air core has an average radius of 15 cm, area of cross-section 12 cm2 and has 1200 turns. Calculate the self-inductance of the toroid. Assume the field to be uniform across the cross-section of the toroid. [CBSE (F) 2014]
Solution.
Here, r = 15 cm = 0.15 m, A = 12 cm2 = 12 × 10–4 m2 and N = 1200
Self inductance, L = μ0N2A/l = μ0N2A/(2πr)
= (4π × 10–7 × (1200)2 × 12 × 10–4)/(2π × 0.15) = 2.3 × 10–3 H.
Teacher's Note: A toroid has mean length 2πr, so L = μ0 N² A / (2πr).
Exam Note: Use mean circumference 2πr as the length.
Question 11. The closed loop (PQRS) of wire is moved out of a uniform magnetic field at right angles to the plane of the paper as shown in the figure. Predict the direction of the induced current in the loop. [CBSE (F) 2012]
Solution.
So far the loop remains in the magnetic field, there is no change in magnetic flux linked with the loop and so no current will be induced in it, but when the loop comes out of the magnetic field, the flux linked with it will decrease and so the current will be induced so as to oppose the decrease in magnetic flux, i.e., it will cause magnetic field downwards; so the direction of current will be clockwise.
Teacher's Note: No emf while the loop is fully inside; once leaving, falling inward flux is opposed by clockwise current.
Exam Note: Separate inside motion (no current) from leaving (clockwise).
Question 12. A 0.5 m long metal rod PQ completes the circuit as shown in the figure. The area of the circuit is perpendicular to the magnetic field of flux density 0.15 T. If the resistance of the total circuit is 3 Ω calculate the force needed to move the rod in the direction as indicated with a constant speed of 2 ms–1.
Solution.
Given: l = 0.5 m, B = 0.15 T, R = 3 Ω, v = 2 ms–1
emf, ε = vBl = 2 × 0.15 × 0.5 = 0.15 V
Current, I = ε/R = vBl/R = 0.15/3 = 0.05 A
Force needed to move the rod,
F = BIl = B × (vBl/R) × l = vB2l2/R
= (2 × (0.15)2 × (0.5)2)/3 = 3.75 × 10–3 N
Teacher's Note: At constant speed the applied force equals the magnetic drag B I l, which is v B² l² / R.
Exam Note: Find emf, then current, then F = BIl.
Question 13. If the self-inductance of an iron core inductor increases from 0·01 mH to 10 mH on introducing the iron core into it, what is the relative permeability of the core material used?
Solution.
Relative permeability μr = Lmedium/Lair = 10 mH/0.01 mH = 1000
Teacher's Note: Self-inductance scales with core permeability, so the ratio of inductances gives relative permeability: 10/0.01.
Exam Note: Divide: 10 mH by 0.01 mH.
Question 14. Fig. shows two positions of a loop PQR in a perpendicular uniform magnetic field. In which position of the coil is there an induced emf?
Solution.
In position (i), the coil remains as such in magnetic field, so there is no magnetic flux change in the coil, hence no emf is induced.
In position (ii) the coil is coming out of the magnetic field, so the magnetic flux linked with it decreases and so an emf is induced in the coil.
Teacher's Note: Emf needs a changing flux: a loop wholly inside a uniform field has none; leaving the field changes it.
Exam Note: Answer position (ii); justify with changing flux.
Question 15. In the figure given below, a bar magnet moving towards the right or left induces an emf in the coils (1) and (2). Find, giving reason, the directions of the induced currents through the resistors AB and CD when the magnet is moving (a) towards the right, and (b) towards the left.
Solution.
(a) When magnet moves towards the right, the nearer faces of coils 1 and 2 act as south poles, so current induced in AB is from B to A and in coil 2 from C to D.
(b) When magnet moves towards left, the nearer faces of coils act as north poles, so current induced in coil 1 will be from A to B and in coil 2 from D to C.
Teacher's Note: Moving right, N-pole recedes from coil 1 and S-pole nears coil 2, so both facing ends turn S.
Exam Note: Fix pole on each near face first.
Question 16. Two coils of wire A and B are placed mutually perpendicular as shown in figure. When current is changed in any one coil, will the current induce in another coil?
Solution.
No; this is because the magnetic field due to current in coil (A or B) will be parallel to the plane of the other coil (A or B). Hence, the magnetic flux linked with the other coil will be zero and so no current will be induced in it.
Teacher's Note: Each coil's field lies in the other coil's plane, so no flux links it however the current changes.
Exam Note: Explain via zero flux in perpendicular coils.
Question 17. A cylindrical bar magnet is kept along the axis of a circular coil and near it as shown in fig. Will there be any induced emf at the terminals of the coil, when the magnet is rotated
(i) About its own axis and
(ii) About an axis perpendicular to the length of the magnet?
Solution.
(i) When the magnet is rotated about its own axis, then due to symmetry of magnet the magnetic flux linked with circular coil remains unchanged, hence no emf is induced at terminals of coil.
(ii) When the magnet is rotated about an axis perpendicular to the length, the positions of N and S poles of magnet changes continuously; so the magnetic flux linked with the coil changes continuously; hence the emf is induced at the terminals of the coil.
Teacher's Note: Spinning about its own axis leaves the field pattern unchanged; tumbling end-over-end keeps changing the flux.
Exam Note: Answer no for (i), yes for (ii).
Question 18. Consider a closed loop C in a magnetic field (see figure). The flux passing through the loop is defined by choosing a surface whose edge coincides with the loop and using the formula φ = B1·dA1 + B2·dA2 + …
Now if we chose two different surfaces S1 and S2 having C as their edge, would we get the same answer for flux. Justify your answer. [NCERT Exemplar]
Solution.
One gets the same answer for flux. Flux can be thought of as the number of magnetic field lines passing through the surface (We draw dN = BΔA lines in a area ΔA perpendicular to B). As field lines of B cannot end or start in space (they form closed loops) number of lines passing through surface S1 must be the same as the number of lines passing through the surface S2.
Teacher's Note: Field lines form closed loops, so every line piercing S1 also pierces S2; flux depends only on the edge C.
Exam Note: Cite closed field lines; flux is the same.
Free study material for Physics
Step-by-Step Xam Idea Solutions for Class 12 Math
Complete Math Solutions for Xam Idea Solutions Class 12 Physics Chapter 6 Electromagnetic Induction Short Answer Questions I
Access the complete chapter-wise PDF for Xam Idea Solutions Class 12 Physics Chapter 6 Electromagnetic Induction Short Answer Questions I. These structured Xam Idea Solutions solutions for Class 12 Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Concept-Driven Math Answers
Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.
Next Steps in Your Mathematics Revision
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.