Step-by-Step Solutions for Class 12 Physics Chapter 03 Current Electricity
Review structured textbook solutions for Class 12 Physics Chapter 03 Current Electricity prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Download Chapter 03 Current Electricity Textbook Solutions PDF
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Short Answer Questions II
Question 1. (i) Derive an expression for drift velocity of free electrons. (ii) How does drift velocity of electrons in a metallic conductor vary with increase in temperature? Explain. [CBSE (Central) 2016]
Solution.
(i) When a potential difference is applied across a conductor, an electric field is produced and free electrons are acted upon by an electric force (Fe). Due to this, electrons accelerate and keep colliding with each other and acquire a constant (average) velocity vd called drift velocity.
Electric force on electron Fe = −eE
If m is the mass of electron, then its acceleration a = F/m = −eE/m
Now, v = u + at. Here, u = 0, t = τ (relaxation time), v = vd
vd = 0 − (eE/m)τ ⇒ vd = −(eτ/m)E
(ii) With rise of temperature, the rate of collision of electrons with ions of lattice increases, so relaxation time decreases. As a result the drift velocity of electrons decreases with the rise of temperature.
Teacher's Note: Electrons accelerate for an average time τ between collisions; higher temperature shortens τ, so vd = eτE/m falls.
Exam Note: vd = eτE/m; falls with temperature.
Question 2. (a) State Kirchhoff’s rules and explain on what basis they are justified. (b) Two cells of emfs E1 and E2 and internal resistances r1 and r2 are connected in parallel. Derive the expression for the (i) emf and (ii) internal resistance of a single equivalent cell which can replace this combination. [CBSE Patna 2015]
Solution.
(a) Kirchhoff’s Laws
(i) First law (or junction law): The algebraic sum of currents meeting at any junction is zero, i.e., ∑I = 0. This law is based on conservation of charge.
(ii) Second law (or loop law): The algebraic sum of potential differences of different circuit elements of a closed circuit (or mesh) is zero, i.e., ∑V = 0. This law is based on conservation of energy.
(b) Let I1 and I2 be the currents leaving the positive terminals of the cells (Fig. a), and at the point B, I = I1 + I2 …(i)
Let V be the potential difference between points A and B of the combination of the cells, so V = E1 − I1r1 …(ii) (across the cells) and V = E2 − I2r2 …(iii)
From equations (i), (ii) and (iii), we get I = (E1 − V)/r1 + (E2 − V)/r2 = (E1/r1 + E2/r2) − V(1/r1 + 1/r2) …(iv)
Fig. (b) shows the equivalent cell, so for the same potential difference V = Eeq − Ireq or I = Eeq/req − V/req …(v)
On comparing Eq. (iv) and (v), we get Eeq/req = E1/r1 + E2/r2 and 1/req = 1/r1 + 1/r2 ⇒ req = r1r2/(r1 + r2)
On further solving, Eeq(1/r1 + 1/r2) = E1/r1 + E2/r2 ⇒ Eeq = (E1r2 + E2r1)/(r1 + r2)
Teacher's Note: Charge conservation gives the junction rule, energy conservation the loop rule; matching coefficients of V gives Eeq and req.
Exam Note: Eeq = (E1r2 + E2r1)/(r1 + r2).
Question 3. Plot a graph showing the variation of current density (J) versus the electric field (E) for two conductors of different materials. What information from this plot regarding the properties of the conducting material, can be obtained which can be used to select suitable materials for use in making (i) standard resistance and (ii) connecting wires in electric circuits? Electron drift speed is estimated to be of the order of mm s−1. Yet large current of the order of few amperes can be set up in the wire. Explain briefly. [CBSE Panchkula 2015]
Solution.
As we know that the drift velocity of the free electrons in a conducting material is given by vd = −(eE/m)τ …(1)
And the flow of the current due to drifting electrons I = neAvd …(2)
From relations (1) and (2), we get I = neA(eEτ/m) = (ne2Aτ/m)E
Current density, |J| = I/A = (ne2τ/m)E ⇒ |J| = (1/ρ)E, where ρ = m/(ne2τ)
⇒ Current density, J ∝ E, where 1/ρ represents the slope of the J–E graph.
Let ρA be the resistivity of the standard resistance A and ρB the resistivity of the connecting wire, i.e., ρB < ρA. So the graph of J vs E can be given as shown. The line with the smaller slope (higher resistivity) suits standard resistances; the line with the larger slope (lower resistivity) suits connecting wires.
Information regarding current flow:
(i) When the circuit is closed, an electric field gets established through the conductor with the speed of light.
(ii) Localised electrons at all places inside the conductor begin to drift instantly and current flow occurs immediately.
(iii) In the relation I = neAvd, the free electron number density is of the order of 1029 m−3; even though the drift velocity is of the order of a few mm/s or 10−3 m/s, the current flow becomes of the order of a few amperes.
Here, drift velocity vd is very small (of the order of mm s−1), but electron number density (n) is very large. Hence, large current can be set up in the wire.
Teacher's Note: The J–E slope is 1/ρ; a steep line means low resistivity, a shallow line high resistivity.
Exam Note: Slope of J–E = 1/ρ; I = neAvd explains large current.
Question 4. A metal rod of square cross-sectional area A having length l has current I flowing through it when a potential difference of V volt is applied across its ends (figure (i)). Now the rod is cut parallel to its length into two identical pieces and joined as shown in figure (ii). What potential difference must be maintained across the length 2l so that the current in the rod is still I? [CBSE (F) 2016]
Solution.
Let the resistance of the metal rod having cross-sectional area A and length l be R1 = ρl/A.
Also, the resistance of the metal rod having cross-sectional area A/2 and length 2l is R2 = ρ(2l)/(A/2) = 4R1 [∵ R = ρl/A]
Let V′ be the potential difference maintained across the rod. When the rod is cut parallel and rejoined by length, the length of the conductor becomes 2l and the area decreases to A/2.
For maintaining the same current, I = V/R1 = V′/R2 = V′/4R1 ⇒ V′ = 4V
The new potential applied across the metal rod will be four times the original potential (V).
Teacher's Note: Doubling length and halving area quadruples resistance, so four times the voltage keeps the current unchanged.
Exam Note: V′ = 4V.
Question 5. Two metallic wires, P1 and P2 of the same material and same length but different cross-sectional areas, A1 and A2 are joined together and connected to a source of emf. Find the ratio of the drift velocities of free electrons in the two wires when they are connected (i) in series, and (ii) in parallel. [CBSE (F) 2017]
Solution.
We know that I = neAvd ⇒ vd = I/(neA)
Let R1 and R2 be the resistances of P1 and P2, and A1 and A2 their cross-sectional areas respectively. ∴ R1 = ρl/A1 and R2 = ρl/A2
(i) When connected in series (the same current I flows through both wires):
vd1/vd2 = [ε/((ρl/A1 + ρl/A2) neA1)] / [ε/((ρl/A1 + ρl/A2) neA2)] = A2/A1
(ii) When connected in parallel (the same potential difference ε across each wire):
vd1/vd2 = [(ε/ρl) · (1/neA1) · A1] / [(ε/ρl) · (1/neA2) · A2] = 1
Series arrangement:
Parallel arrangement:
Teacher's Note: In series the current is common, so vd ∝ 1/A; in parallel vd = V/(neρl) is independent of area.
Exam Note: (i) A2 : A1; (ii) 1 : 1.
Question 6. Two heating elements of resistance R1 and R2 when operated at a constant supply of voltage, V, consume powers P1 and P2 respectively. Deduce the expressions for the power of their combination when they are, in turn, connected in (i) series combination (ii) parallel combination.
Solution.
In series combination
Net resistance, R = R1 + R2 …(i)
As the heating elements are operated at the same voltage V, we have R = V2/P, R1 = V2/P1 and R2 = V2/P2
∴ From equation (i), V2/P = V2/P1 + V2/P2 ⇒ 1/P = 1/P1 + 1/P2, i.e. P = P1P2/(P1 + P2)
In parallel combination
Net resistance, 1/R = 1/R1 + 1/R2. With R = V2/P, R1 = V2/P1, R2 = V2/P2 we get P/V2 = P1/V2 + P2/V2 ⇒ P = P1 + P2
Teacher's Note: Use P = V2/R at fixed V: resistances in series add, so reciprocals of powers add; in parallel powers add.
Exam Note: Series: P = P1P2/(P1+P2); parallel: P1+P2.
Question 7. (i) The potential difference applied across a given resistor is altered so that the heat produced per second increases by a factor of 9. By what factor does the applied potential difference change? (ii) In the figure shown, an ammeter A and a resistor of 4 Ω are connected to the terminals of the source. The emf of the source is 12 V having an internal resistance of 2 Ω. Calculate the voltmeter and ammeter readings. [CBSE AI 2017]
Solution.
(i) Heat generated H = V2t/R
Given H′ = 9H
∴ V′2t/R = 9 × V2t/R ⇒ V′2 = 9V2 ⇒ V′ = √9 × V = 3V
∴ The potential difference increases by a factor of √9, i.e., 3.
(ii) Given: emf E = 12 V, internal resistance r = 2 Ω, external resistance R = 4 Ω
Ammeter reading, I = E/(R + r) = 12/(4 + 2) = 12/6 ∴ I = 2 A
Voltmeter reading, V = E − Ir = 12 − (2 × 2) ∴ V = 8 V
Teacher's Note: Heat per second is proportional to V2, so nine times the heat means three times the voltage.
Exam Note: (i) 3 times; (ii) 2 A, 8 V.
Question 8. Calculate the steady current through the 2 Ω resistor in the circuit shown below. [CBSE (F) 2010]
Solution.
In steady state there is no current in the capacitor branch, so the equivalent circuit is a 6 V cell with the parallel combination of 2 Ω and 3 Ω in series with 2.8 Ω.
Net resistance of circuit, Req = (2 × 3)/(2 + 3) + 2.8 = 1.2 + 2.8 = 4 Ω
Net emf, E = 6 V
Current in circuit, I = E/Req = 6/4 = 1.5 A
Potential difference across the parallel combination of 2 Ω and 3 Ω resistances: V = IR′ = 1.5 × 1.2 = 1.8 V
Current in the 2 Ω resistance, I1 = V′/R1 = 1.8/2 = 0.9 A
Teacher's Note: A capacitor blocks steady current; only the 2 Ω || 3 Ω block and 2.8 Ω carry current.
Exam Note: Current in 2 Ω resistor = 0.9 A.
Question 9. Two identical cells of emf 1.5 V each joined in parallel supply energy to an external circuit consisting of two resistances of 7 Ω each joined in parallel. A very high resistance voltmeter reads the terminal voltage of cells to be 1.4 V. Calculate the internal resistance of each cell. [CBSE (North) 2016]
Solution.
Here, E = 1.5 V, V = 1.4 V
Resistance of external circuit = equivalent resistance of two resistances of 7 Ω connected in parallel (figure):
R = R1R2/(R1 + R2) = (7 × 7)/(7 + 7) Ω = 3.5 Ω
Let r′ be the total internal resistance of the two cells, then r′ = [(E − V)/V]R = [(1.5 − 1.4)/1.4] × 3.5 = 0.25 Ω
As the two cells of internal resistance r each have been connected in parallel, 1/r′ = 1/r + 1/r ⇒ 1/0.25 = 2/r ⇒ r = 0.25 × 2 = 0.5 Ω
Teacher's Note: Find the equivalent internal resistance from V = E − Ir′, then split it between two identical cells in parallel.
Exam Note: r = 0.5 Ω for each cell.
Question 10. In the meter bridge experiment, balance point was observed at J with AJ = l. (i) The values of R and X were doubled and then interchanged. What would be the new position of balance point? (ii) If the galvanometer and battery are interchanged at the balance position, how will the balance point get affected? [CBSE (AI) 2011]
Solution.
(i) R/X = l/(100 − l) …(i)
When both R and X are doubled and then interchanged, the new balance length becomes l′ given by 2X/2R = l′/(100 − l′) ⇒ X/R = l′/(100 − l′) …(ii)
From (i) and (ii), (100 − l)/l = l′/(100 − l′) ⇒ l′ = (100 − l)
(ii) If the galvanometer and battery are interchanged, there is no effect on the balance point.
Teacher's Note: Doubling both resistances keeps their ratio; interchanging then mirrors the balance point about the centre of the wire.
Exam Note: (i) New balance length = (100 − l) cm; (ii) no effect.
Question 11. In a meter bridge shown in the figure, the balance point is found to be 40 cm from end A. If a resistance of 10 Ω is connected in series with R, balance point is obtained 60 cm from A. Calculate the value of R and S. [CBSE Patna 2015]
Solution.
R/S = 40/60 ⇒ 3R = 2S ⇒ R = 2S/3 …(i)
(R + 10)/S = 60/40 ⇒ 2R + 20 = 3S …(ii)
From equations (i) and (ii), we get 2 × (2S/3) + 20 = 3S ⇒ S = 12 ohm
From equation (i), R = (2 × 12)/3 ⇒ R = 8 ohm
Teacher's Note: Write the bridge ratio before and after adding 10 Ω in series with R, then solve the two equations.
Exam Note: R = 8 Ω, S = 12 Ω.
Question 12. In the circuit diagram shown, AB is a uniform wire of resistance 15 Ω and length 1 m. It is connected to a cell E1 of emf 2 V and negligible internal resistance and a resistance R. The balance point with another cell E2 of emf 75 mV is found at 30 cm from end A. Calculate the value of the resistance R. [CBSE Chennai 2015]
Solution.
Current drawn from the cell, E1 = 2 V: I = E1/(15 + R) = 2/(15 + R)
Potential drop across the wire AB: VAB = I × 15 = (2 × 15)/(15 + R) = 30/(15 + R)
Since the wire length is 1 m or 100 cm, the potential gradient along the wire is K = VAB/100 cm = 30/[100(15 + R)]
At the balance point, E2 = Kl2
75 mV = {30/[100(15 + R)]} × 30 cm
75 × 10−3 × 100(15 + R) = 900
15 + R = 9000/75 = 120
∴ R = 120 − 15 = 105 ohm
Teacher's Note: Find the gradient from the wire current, then use E2 = k × 30 cm.
Exam Note: R = 105 Ω.
Question 13. Calculate the value of the current drawn from a 5 V battery in the circuit as shown. [CBSE (F) 2013]
Solution.
The equivalent Wheatstone bridge for the given combination is shown in the figure.
The resistance of arm ACD, RS1 = 10 + 20 = 30 Ω
Also, the resistance of arm ABD, RS2 = 5 + 10 = 15 Ω
Since the condition R/Q = R/S (i.e., 5/10 = 10/20) is satisfied, it is a balanced bridge. No current flows along arm BC.
∴ Equivalent resistance = (RS1 × RS2)/(RS1 + RS2) = (30 × 15)/(30 + 15) = (30 × 15)/45 = 10 Ω
Current drawn from the source, I = V/R = 5/10 = 1/2 A = 0.5 A
Teacher's Note: The bridge is balanced (5/10 = 10/20), so the middle 10 Ω carries no current.
Exam Note: I = 0.5 A.
Question 14. State Kirchhoff’s rules. Use these rules to write the expressions for the currents I1, I2 and I3 in the circuit diagram shown. [CBSE (AI) 2010]
Solution.
Kirchhoff’s Rules:
(i) The algebraic sum of currents meeting at any junction is zero, i.e., ∑I = 0
(ii) The algebraic sum of potential differences across circuit elements of a closed circuit is zero, i.e., ∑V = 0
From Kirchhoff’s first law, I3 = I1 + I2 …(i)
For applying Kirchhoff’s second law to mesh ABDC: −2 − 4I1 + 3I2 + 1 = 0 ⇒ 4I1 − 3I2 = −1 …(ii)
Applying Kirchhoff’s II law to mesh ABEFA: −2 − 4I1 − 2I3 + 4 = 0 ⇒ 4I1 + 2I3 = 2 or 2I1 + I3 = 1
Using (i) we get 2I1 + (I1 + I2) = 1 or 3I1 + I2 = 1 …(iii)
Solving (ii) and (iii), we get I1 = 2/13 A, I2 = 1 − 3I1 = 7/13 A
so, I3 = I1 + I2 = 9/13 A
Teacher's Note: The junction rule gives I3 = I1 + I2; two loop equations then fix the three currents.
Exam Note: I1 = 2/13 A, I2 = 7/13 A, I3 = 9/13 A.
Question 15. Use Kirchhoff’s rules to determine the potential difference between the points A and D when no current flows in the arm BE of the electric network shown in the figure. [CBSE Allahabad 2015]
Solution.
According to Kirchhoff’s junction rule at E or B: I3 = I2 + I1
Since I2 = 0 in the arm BE as given in the question ⇒ I3 = I1
Using the loop rule in the loop AFEBA: +6 V − 2I3 + 1 V − 3I3 − I2R1 + 3 V = 0 ⇒ 2I3 + 3I3 + I2R1 = 10 V
Since I2 = 0, so 5I3 = 10 V ⇒ I3 = 2 A ∴ I3 = I1 = 2 A
The potential difference between A and D, along the branch AFED of the closed circuit: VA − 2I3 + 1 V − 3I3 − VD = 0
⇒ VA − VD = 2I3 − 1 + 3I3 = 2 × 2 − 1 + 3 × 2 = 9 V
Teacher's Note: No current in BE means a single loop current I3; use the loop rule, then add the drops along AFED.
Exam Note: I = 2 A; VA − VD = 9 V.
Question 16. (i) Using Kirchhoff’s rules, calculate the current in the arm AC of the given circuit. (ii) On what principle does the meter bridge work? Why are the metal strips used in the bridge? [CBSE South 2016]
Solution.
(i) For the mesh EFCAE: −30I1 + 40 − 40(I1 + I2) = 0 ⇒ 7I1 + 4I2 = 4 …(i)
For the mesh ACDBA: 40(I1 + I2) − 40 + 20I2 − 80 = 0 ⇒ 40I1 + 60I2 = 120 ⇒ 2I1 + 3I2 = 6 …(ii)
Solving (i) and (ii), we get I1 = −12/13 A and I2 = 34/13 A
∴ Current through arm AC = I1 + I2 = 22/13 A
(ii) The meter bridge works on the principle of a balanced Wheatstone bridge. The thick metal (copper) strips are used because they have negligible resistance, so they do not alter the resistances in the gaps (and avoid errors from end and contact resistance).
Teacher's Note: Take clockwise loop directions with I1 and I2; the current in AC is the sum I1 + I2.
Exam Note: IAC = 22/13 A ≈ 1.7 A.
Question 17. (i) Write the principle of working of a metre bridge. (ii) In a metre bridge, the balance point is found at a distance l1 with resistances R and S as shown in the figure. An unknown resistance X is now connected in parallel to the resistance S and the balance point is found at a distance l2. Obtain a formula for X in terms of l1, l2 and S. [CBSE (AI) 2017]
Solution.
(i) The working of a meter bridge is based on the principle of a balanced Wheatstone bridge. According to the principle, the balancing condition is P/Q = R/S (when Ig = 0). For balancing lengths in a meter bridge, P/Q = R/S ⇒ l/(100 − l) = R/S.
(ii) Initially R/S = l1/(100 − l1) …(1)
With X in parallel with S, the new resistance is S′ = SX/(S + X) and R/S′ = l2/(100 − l2) …(2)
From (1) and (2): S′ = S · l1(100 − l2)/[l2(100 − l1)]
Since 1/X = 1/S′ − 1/S = (1/S)[l2(100 − l1)/(l1(100 − l2)) − 1] = (1/S) · 100(l2 − l1)/[l1(100 − l2)]
∴ X = S l1(100 − l2)/[100(l2 − l1)]
Teacher's Note: Find S′ from l2, then use 1/S′ = 1/S + 1/X.
Exam Note: X = S l1(100 − l2)/[100(l2 − l1)].
Question 18. A potentiometer wire of length 1 m is connected to a driver cell of emf 3 V as shown in the figure. When a cell of 1.5 V emf is used in the secondary circuit, the balance point is found to be 60 cm. On replacing this cell and using a cell of unknown emf, the balance point shifts to 80 cm. (i) Calculate unknown emf of the cell. (ii) Explain with reason, whether the circuit works, if the driver cell is replaced with a cell of emf 1 V. (iii) Does the high resistance R, used in the secondary circuit affect the balance point? Justify your answer. [CBSE Delhi 2008]
Solution.
(i) Unknown emf ε2 is given by ε2/ε1 = l2/l1 ⇒ ε2 = (l2/l1)ε1
Given ε1 = 1.5 V, l1 = 60 cm, l2 = 80 cm
∴ ε2 = (80/60) × 1.5 V = 2.0 V
(ii) The circuit will not work if the emf of the driver cell is 1 V (less than that of the cell in the secondary circuit), because the total voltage across wire AB is 1 V, which cannot balance the voltage V.
(iii) No, since at the balance point no current flows through the galvanometer G, i.e., the cell remains in open circuit.
Teacher's Note: Balance lengths are proportional to emfs; the driver emf must exceed the emf being balanced or no null point exists.
Exam Note: (i) 2.0 V; (ii) fails; (iii) no effect.
Question 19. In a meter bridge with R and S in the gaps, the null point is found at 40 cm from A. If a resistance of 30 Ω is connected in parallel with S, the null point occurs at 50 cm from A. Determine the values of R and S. [CBSE East 2016]
Solution.
In the first case l1 = 40 cm: R/S = l1/(100 − l1) ⇒ R/S = 40/60 = 2/3 …(i)
In the second case, when S and 30 Ω are in parallel, the balancing length l2 = 50 cm: S′ = 30S/(30 + S) …(ii)
R/S′ = 50/(100 − 50) = 1 ⇒ S′ = R …(iii)
From (i), S = (3/2)R. Substituting this value in (ii), we get S′ = 30 × (3R/2)/(30 + 3R/2) = 45R/(30 + 3R/2)
Also from (iii), S′ = R ∴ 45R/(30 + 3R/2) = R ⇒ 45 = 30 + (3/2)R ⇒ (3/2)R = 15 or R = 10 Ω ⇒ S = (3/2) × R = (3/2) × 10 = 15 Ω
Teacher's Note: Write the bridge condition for S alone, then for S in parallel with 30 Ω, and solve the two equations.
Exam Note: R = 10 Ω, S = 15 Ω.
Question 20. In the circuit shown, R1 = 4 Ω, R2 = R3 = 15 Ω, R4 = 30 Ω and E = 10 V. Calculate the equivalent resistance of the circuit and the current in each resistor. [CBSE Delhi 2011] [HOTS]
Solution.
Given R1 = 4 Ω, R2 = R3 = 15 Ω, R4 = 30 Ω, E = 10 V.
Equivalent resistance: R2, R3 and R4 are in parallel, so their effective resistance (R) is given by 1/R = 1/R2 + 1/R3 + 1/R4 = 1/15 + 1/15 + 1/30 ⇒ R = 6 Ω
R1 is in series with R, so the equivalent resistance Req = R + R1 = 6 + 4 = 10 Ω.
Currents: I1 = E/Req = 10/10 = 1 A …(i)
This current is divided at A into three parts I2, I3 and I4. ∴ I2 + I3 + I4 = 1 A …(ii)
Also, I2R2 = I3R3 = I4R4 ⇒ I2 × 15 = I3 × 15 = I4 × 30 ⇒ I2 = I3 = 2I4 …(iii)
Substituting values of I2, I3 in (ii), we get 2I4 + 2I4 + I4 = 1 A ⇒ I4 = 0.2 A
∴ I2 = I3 = 2 × 0.2 = 0.4 A
Thus, I1 = 1 A, I2 = I3 = 0.4 A and I4 = 0.2 A
Teacher's Note: The three parallel resistors give 6 Ω; the 1 A total current then divides in inverse ratio of resistances.
Exam Note: Req = 10 Ω; 1 A, 0.4 A, 0.4 A, 0.2 A.
Question 21. In the following potentiometer circuit AB is a uniform wire of length 1 m and resistance 10 Ω. Calculate the potential gradient along the wire and balance length AO. [CBSE Delhi 2016] [HOTS]
Solution.
Current flowing in the potentiometer wire: I = E/Rtotal = 2.0/(15 + 10) = 2/25 A
Potential difference across the wire = (2/25) × 10 = 20/25 = 0.8 V
Potential gradient k = VAB/lAB = 0.8/1.0 = 0.8 V/m
Now, current flowing in the circuit containing the experimental cell: 1.5/(1.2 + 0.3) = 1 A
Potential difference across length AO = 0.3 × 1 = 0.3 V
Length AO = 0.3/0.8 m = (0.3/0.8) × 100 cm = 37.5 cm
Teacher's Note: Gradient = voltage across wire / length; the balanced voltage is the drop across the 0.3 Ω resistor.
Exam Note: k = 0.8 V/m; AO = 37.5 cm.
Question 22. A resistance of R draws current from a potentiometer. The potentiometer wire, AB, has a total resistance of R0. A voltage V is supplied to the potentiometer. Derive an expression for the voltage across R when the sliding contact is in the middle of potentiometer wire. [CBSE Delhi 2017]
Solution.
Effective resistance between points A and C is given by 1/R1 = 1/R + 1/(R0/2) = (R0/2 + R)/(R · R0/2) ⇒ R1 = R(R0/2)/(R0/2 + R)
Effective resistance between points A and B is given by R2 = R(R0/2)/(R0/2 + R) + R0/2
Current drawn from the voltage source, I = V/R2 = V/{[R(R0/2)/(R + R0/2)] + R0/2}
Let the current through R be I1: I1 = I(R0/2)/(R + R0/2)
Voltage across R is given by V1 = I1R = [IR0/(2(R + R0/2))] · R
On substituting I = V/R2 and simplifying (R2 = R0(4R + R0)/[2(2R + R0)]):
V1 = 2RV/(R0 + 4R)
Teacher's Note: Slider at the middle: R is in parallel with half the wire, in series with the other half.
Exam Note: V1 = 2RV/(R0 + 4R).
Question 23. A cell of emf ‘E’ and internal resistance ‘r’ is connected across a variable load resistor R. Draw the plots of the terminal voltage V versus (i) R and (ii) the current I. [CBSE Delhi 2015] [HOTS]
Solution.
(i) Current in circuit I = ε/(R + r). Terminal potential difference V = IR = [ε/(R + r)]R = ε/(1 + r/R)
When R increases, r/R decreases, so the terminal potential difference increases with the increase of R.
When R = 0, V → 0; when R = r, V = ε/2; when R → ∞ (open circuit), V = ε. The graph of terminal potential difference V versus R is shown in the first figure.
(ii) V = E − Ir ⇒ I = (E − V)/r. The graph of V versus I is a straight line of negative slope −r with intercept ε on the V-axis, as shown in the second figure.
Teacher's Note: V = ε/(1 + r/R) rises to ε, equal to ε/2 at R = r; V against I is linear.
Exam Note: V–R: rising curve to ε; V–I: straight line, slope −r.
Question 24. Define resistivity of a conductor. Plot a graph showing the variation of resistivity with temperature for a metallic conductor. How does one explain such a behaviour, using the mathematical expression of the resistivity of a material?
Solution.
We know that, R = ρl/A. If l = 1, A = 1 ⇒ ρ = R
Thus, the resistivity of a material is numerically equal to the resistance of the conductor having unit length and unit cross-sectional area.
The resistivity of a material is found to be dependent on the temperature. Different materials do not exhibit the same dependence on temperature. Over a limited range of temperatures, that is not too large, the resistivity of a metallic conductor is approximately given by ρT = ρ0[1 + α(T − T0)] …(i)
Where ρT is the resistivity at a temperature T and ρ0 is the same at a reference temperature T0, α is called the temperature coefficient of resistivity.
Relation (i) implies that a graph of ρT plotted against T would be a straight line. At temperatures much lower than 0°C, the graph, however, deviates considerably from a straight line (figure: resistivity ρT of a metallic conductor as a function of temperature T).
Teacher's Note: For metals α is positive, so ρT = ρ0[1 + α(T − T0)] rises with temperature, almost linearly.
Exam Note: ρ = R·A/l; ρ of metals rises with T.
Question 25. Write the mathematical relation for the resistivity of a material in terms of relaxation time, number density, mass and charge of charge carriers in it. Explain using this relation, why the resistivity of a metal increases and that of a semiconductor decreases with rise in temperature.
Solution.
Resistivity of a material, ρ = m/(ne2τ)
Where m is mass, e is charge on charge carrier, n is number density and τ is relaxation time.
For a metallic conductor: When the temperature of a metal increases, the number of collisions of electrons with the ion-lattice increases, so relaxation time decreases, as resistivity ρ ∝ 1/τ, so resistivity of the material increases with rise of temperature.
For a semiconductor: When temperature increases, the covalent bonds between valence electrons of atoms of the semiconductor break, so more charge carriers (electrons and holes) become free. In other words the number density of charge carriers increases, ρ ∝ 1/n, so resistivity of the semiconductor decreases with the rise of temperature.
Teacher's Note: In metals τ falls with T; in semiconductors n rises so strongly that it outweighs the fall in τ.
Exam Note: ρ = m/(ne2τ); τ falls in metals, n rises in semiconductors.
Question 26. Explain the variation of conductivity with temperature for (i) a metallic conductor, (ii) ionic conductors and (iii) semiconductors.
Solution.
Conductivity of a metallic conductor σ = 1/ρ = ne2τ/m.
Where m = mass of charge carrier, e = charge on each carrier, τ = relaxation time, n = number density of charge carriers.
(i) With rise of temperature, the collision of electrons with fixed lattice ions/atoms increases so that relaxation time (τ) decreases. Consequently, the conductivity of metals decreases with rise of temperature (graph shown).
(ii) The conductivity of an ionic conductor increases with increase of temperature because with increase of temperature, the ionic bonds break releasing positive and negative ions, which are the charge carriers in ionic conductors.
(iii) In the case of a semiconductor, when temperature increases, covalent bonds break and charge carriers (electrons and holes) become free, i.e., n increases, so conductivity increases with rise of temperature.
Teacher's Note: Conductivity ne2τ/m depends on carrier number n and relaxation time τ: metals lose τ, ionic conductors and semiconductors gain n.
Exam Note: Metals: σ falls; ionic and semiconductors: σ rises.
Question 27. Two heater coils made of same material are connected in parallel across the mains. The length and diameter of the wire of one of coils are double that of the other. Which one of them will produce more heat?
Solution.
We have the resistance of one wire R1 = ρl/A = ρl/πr2 = 4ρl/πD2, where l is the length and D is the diameter of the wire.
The resistance of the second wire of double the length and double the diameter is R2 = 4ρ(2l)/π(2D)2 = (4ρl/πD2) · (1/2), i.e., R2 = R1/2
Heat produced per second H = V2/R ∝ 1/R
As the second coil has resistance equal to half of the first coil, therefore the heat produced in the second coil is double that in the first coil.
Teacher's Note: R = 4ρl/πD2: doubling l and D halves R, and at equal voltage heat rate is proportional to 1/R.
Exam Note: Longer, thicker coil gives double heat.
Question 28. Two heaters are marked 200 V, 300 W and 200 V, 600 W. If the heaters are connected in series and the combination connected to a 200 V dc supply, which heater will produce more heat?
Solution.
Resistance of heaters R1 = V2/P1 = (200)2/300 = 400/3 Ω
R2 = V2/P2 = (200)2/600 = 400/6 Ω
When the heaters are connected in series, the current in the circuit I = V/(R1 + R2) = 200/(400/3 + 400/6) = 1 A
Heat produced in the 200 V, 300 W heater per second Q1 = I2R1 = (1)2 × 400/3 = 133.33 J s−1
Heat produced in the 200 V, 600 W heater per second Q2 = I2R2 = (1)2 × 400/6 = 66.66 J s−1
Clearly heat produced in the 300 W heater is more than that produced in the 600 W heater.
Teacher's Note: In series the same current flows, so the heater with larger resistance (lower wattage rating) heats more.
Exam Note: 300 W heater produces more heat.
Question 29. Two cells of emf 1 V, 2 V and internal resistances 2 Ω and 1 Ω respectively are connected in (i) series (ii) parallel. What should be the external resistance in the circuit so that the current through the resistance be the same in the two cases? In which case is more heat generated in the cells?
Solution.
For parallel combination,
Net emf, ε = (ε1r2 + ε2r1)/(r1 + r2)
Net internal resistance, rint = r1r2/(r1 + r2)
For series combination, net emf ε = ε1 + ε2 and net internal resistance rint = r1 + r2
Given, ε1 = 1 V, ε2 = 2 V, and r1 = 2 Ω, r2 = 1 Ω, Rext = R
∴ Current, I1 = (ε1 + ε2)/(r1 + r2 + R) = (1 + 2)/(2 + 1 + R) = 3/(3 + R) A …(i)
Current, I2 = [(ε1r2 + ε2r1)/(r1 + r2)]/[R + r1r2/(r1 + r2)] = [(1 × 1 + 2 × 2)/(2 + 1)]/[R + (2 × 1)/(2 + 1)] = (5/3)/(R + 2/3) = 5/(3R + 2) …(ii)
Given I1 = I2 ∴ 3/(3 + R) = 5/(3R + 2) or 9R + 6 = 15 + 5R, 4R = 9 ⇒ R = 9/4 = 2.25 Ω
Heat generated in the external resistance (I2R) is the same in both cases, but heat generated in the cells (I2rint) is more in series than that in the parallel combination of cells.
Teacher's Note: Equate the two currents 3/(3 + R) and 5/(3R + 2); cell heating I2r is larger when rint is larger.
Exam Note: R = 2.25 Ω; more cell heat in series.
Question 30. For the circuit shown here, calculate the potential difference between points B and D.
Solution.
According to Kirchhoff’s first law the distribution of currents is shown in the figure: i in the outer path, (i − i1) through the 2 V cell branch AB and i1 through the diagonal 2 Ω resistor BD.
Applying Kirchhoff’s second law to mesh BADB: −2(i − i1) + 2 − 1 − 1 · (i − i1) + 2i1 = 0 ⇒ 3i − 5i1 = 1 …(i)
Applying Kirchhoff’s law to mesh DCBD: −3i + 3 − 1 − 1 × i − 2i1 = 0 ⇒ 4i + 2i1 = 2 or 2i + i1 = 1 …(ii)
Multiplying equation (ii) with 5, we get 10i + 5i1 = 5 …(iii)
Adding (i) and (iii), we get 13i = 6 ⇒ i = 6/13 A
From (ii), i1 = 1 − 2i = 1 − 12/13 = 1/13 A
Potential difference between B and D is VB − VD = i1 × 2 = 2/13 V
Teacher's Note: Assign currents i and i1, write two mesh equations, and find the drop across the 2 Ω diagonal.
Exam Note: VB − VD = 2/13 V.
Question 31. In a practical Wheatstone bridge circuit, wire AB is 2 m long. When resistance Y = 2.0 Ω and jockey is in position J such that AJ = 1.20 m, there is no current in galvanometer, find the value of unknown resistance X. The resistance per unit length of wire AB = 0.01 Ω/cm. Also calculate the current drawn by the cell of emf 4.0 V and negligible internal resistance.
Solution.
P = Resistance of wire AJ = (1.20 × 100 cm) × (0.01 Ω/cm) = 1.20 Ω
Q = Resistance of wire BJ = [(2 − 1.20) m × 100] × resistance per cm = 0.80 × 100 cm × 0.01 Ω = 0.80 Ω
Y = 2.0 Ω, X = ?
When no current flows through the galvanometer, the bridge is balanced, so P/Q = X/Y ⇒ X = (P/Q)Y or X = (1.20/0.80) × 2.0 = 3.0 Ω
Total resistance of X and Y connected in series, R1 = X + Y = 3.0 + 2.0 = 5.0 Ω
Total resistance of P and Q connected in series (or wire AB), R2 = 2 × 100 × 0.01 = 2.0 Ω
The resistances R1 and R2 are in parallel, so the effective resistance between terminals A and B of the bridge is RAB = R1R2/(R1 + R2) = (5.0 × 2.0)/(5.0 + 2.0) = 10/7 Ω
Current drawn from the battery I = ε/RAB = 4.0/(10/7) = 2.8 A
Teacher's Note: At balance X/Y = P/Q (wire segment resistances); then combine the two parallel paths.
Exam Note: X = 3 Ω; I = 2.8 A.
Question 32. In the given circuit, a metre bridge is shown in the balanced state. The metre bridge wire has a resistance of 1 Ω cm−1. Calculate the unknown resistance X and the current drawn from the battery of a negligible internal resistance if the magnitude of Y is 6 Ω. If at the balancing point, we interchange the position of galvanometer and the cell, how it will affect the position of the galvanometer?
Solution.
At balanced state, X/Y = 40/60 = 2/3 ⇒ X = (2/3)Y = (2/3) × 6 ∴ X = 4 Ω
4 Ω and 6 Ω are in series, so the equivalent resistance is Req = 4 Ω + 6 Ω = 10 Ω
Resistance of bridge wire = 1 ohm/cm × 100 cm = 100 Ω
10 Ω and 100 Ω are in parallel: R = (10 × 100)/(10 + 100) = 1000/110 Ω = 9.09 Ω
Current = 6/9.09 ≈ 0.66 A
There will be no change in the balancing length if we interchange the position of galvanometer and cell.
Teacher's Note: Balance gives X from 40 : 60; the bridge arms (10 Ω) are in parallel with the 100 Ω wire.
Exam Note: X = 4 Ω; I ≈ 0.66 A; no shift.
Question 33. Calculate the current drawn from the battery in the given network shown here. State Kirchhoff’s loop law and name the law on which it is based.
Solution.
The equivalent circuit is as shown in the figure. [∴ The bridge is in balanced condition (3/3 = 2/2), so no current flows through the 5 Ω resistance.]
The two arms (3 + 2) Ω and (3 + 2) Ω are in parallel: 1/R = 1/5 + 1/5 ⇒ R = 5/2 = 2.5 Ω
Current in the circuit = 6/2.5 A = 2.4 A
Kirchhoff’s Loop Law: The algebraic sum of potential differences of different circuit elements of a closed circuit (or mesh) is zero. This law is based on the law of conservation of energy.
Teacher's Note: A balanced bridge ignores the 5 Ω link; the remaining two 5 Ω paths in parallel give 2.5 Ω.
Exam Note: I = 2.4 A; loop law: energy conservation.
Question 34. The graph shown here shows the variation of terminal potential difference V, across a combination of three cells in series to a resistor, versus current i: (i) Calculate the emf of each cell. (ii) For what current i, will the power dissipation of the circuit be maximum? [HOTS]
Solution.
(i) Let ε be the emf and r the internal resistance of each cell. The equation of terminal potential difference V = εeff − i rint becomes V = 3ε − i rint …(i), where rint is the effective (total) internal resistance.
From the figure, when i = 0, V = 6.0 V. From (i), 6 = 3ε − 0 ⇒ ε = 6/3 = 2 V
Thus, the emf of each cell, ε = 2 V.
(ii) From the graph the short-circuit current is 2.0 A, so rint = 6.0/2.0 = 3 Ω. The power dissipated in the external resistor is maximum when R = rint, at which point V = 3.0 V and i = 3.0/3 = 1.0 A (the dotted lines in the graph).
Teacher's Note: V-axis intercept gives total emf 3ε; the power delivered to the load peaks when load resistance equals total internal resistance.
Exam Note: ε = 2 V; maximum power at i = 1.0 A.
Question 35. Two cells of emf 1.5 V and 2 V and internal resistance 1 Ω and 2 Ω respectively are connected in parallel to pass a current in the same direction through an external resistance of 5 Ω. (i) Draw the circuit diagram. (ii) Using Kirchhoff’s laws, calculate the current through each branch of the circuit and potential difference across 5 Ω resistor.
Solution.
(i) The circuit is shown in the figure.
(ii) Suppose I1 and I2 are the currents drawn from cells ε1 and ε2 respectively, then according to Kirchhoff’s junction law, the current in R = 5 Ω is I = I1 + I2.
Applying Kirchhoff’s second law to mesh ABFEA: 1 × I1 + 1.5 − 5(I1 + I2) = 0 ⇒ 6I1 + 5I2 = 1.5 …(i)
Applying Kirchhoff’s second law to mesh CDEFC: −2I2 + 2 − 5(I1 + I2) = 0 ⇒ 5I1 + 7I2 = 2 …(ii)
Solving equations (i) and (ii), we get I1 = 1/34 A, I2 = 9/34 A
I = I1 + I2 = 1/34 + 9/34 = 10/34 A
Potential difference across the R = 5 Ω resistor = (I1 + I2)R = (10/34) × 5 = 25/17 volt
Teacher's Note: Both cells push current the same way; two mesh equations through the shared 5 Ω resistor give I1 and I2.
Exam Note: I1 = 1/34 A, I2 = 9/34 A, V = 25/17 V.
Question 36. (i) Calculate the equivalent resistance of the given electrical network between points A and B. (ii) Also calculate the current through CD and ACB if a 10 V dc source is connected between points A and B and the value of R = 2 Ω.
Solution.
(i) The equivalent circuit is shown in the figure. It is a balanced Wheatstone bridge. So, the resistance connected between C and D is ineffective.
Resistance of arm ACB, R1 = R + R = 2R
Resistance of arm ADB, R2 = R + R = 2R
Equivalent resistance between A and B, RAB is given by 1/RAB = 1/2R + 1/2R = 2/2R ⇒ RAB = R = 2 Ω
(ii) In arm CD, there is no current, ICD = 0.
Current through arm ACB: i1 = V/R1 = 10/2R = 10/(2 × 2) = 10/4 = 2.5 A
Teacher's Note: Removing the redundant structure leaves a symmetric bridge with equal arms, so the CD link carries no current.
Exam Note: RAB = R; ICD = 0; IACB = 2.5 A.
Free study material for Physics
Download Xam Idea Solutions for Class 12 Math PDF
Access Class 12 Mathematics Solutions
Access the complete chapter-wise PDF for Xam Idea Solutions Class 12 Physics Chapter 3 Current Electricity Short Answer Questions II. These structured Xam Idea Solutions solutions for Class 12 Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Concept-Driven Math Answers
Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.
Additional Study Materials for 2026
In addition to these Xam Idea Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.