Step-by-Step Solutions for Class 12 Physics Chapter 03 Current Electricity
Review structured textbook solutions for Class 12 Physics Chapter 03 Current Electricity prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Download Chapter 03 Current Electricity Textbook Solutions PDF
Access the complete solution PDF for Class 12 Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Short Answer Questions I
Question 1. Define the terms (i) Drift velocity, (ii) Relaxation time. [CBSE Delhi 2011, (AI) 2013]
Solution.
(i) Drift Velocity: The average velocity acquired by the free electrons of a conductor in a direction opposite to the externally applied electric field is called drift velocity. The drift velocity will remain the same with lattice ions/atoms.
(ii) Relaxation Time: The average time of free travel of free electrons between two successive collisions is called the relaxation time.
Teacher's Note: Drift velocity is the slow average electron velocity opposite to the field; relaxation time is the mean time between collisions.
Exam Note: Define both clearly.
Question 2. State the underlying principle of a potentiometer. Write two factors by which current sensitivity of a potentiometer can be increased. Why is a potentiometer preferred over a voltmeter for measuring the emf of a cell? [CBSE Patna 2015]
Solution.
Principle: The potential drop across a part of the potentiometer wire is directly proportional to the length of that part of the wire of uniform cross section.
V = kl
Where k is potential gradient.
Current sensitivity of potentiometer wire is also known as potential gradient, and it can be increased.
(i) By increasing the total length of the wire, keeping terminal voltage constant.
(ii) By connecting a suitable extra resistance R in series with the potentiometer. So, less amount of the current flows through the potentiometer wire. Reasons: At the balance point, there is no net current drawn from the cell, and cell is in open circuit condition. Voltmeter has some resistance, when connected across the cell. Some current is drawn, as a result emf of the cell decreases. Hence, emf of the cell cannot be measured by the voltmeter.
Teacher's Note: Potential drop along a uniform wire is proportional to its length, and balance draws no current.
Exam Note: Write V = kl and two sensitivity methods.
Question 3. Answer the following: (i) Why are the connections between the resistors in a meter bridge made of thick copper strips? (ii) Why is it generally preferred to obtain the balance point in the middle of the meter bridge wire? (iii) Which material is used for the meter bridge wire and why? [CBSE (AI) 2014] [HOTS]
Solution.
(i) A thick copper strip offers a negligible resistance, so does not alter the value of resistances used in the meter bridge.
(ii) If the balance point is taken in the middle, it is done to minimise the percentage error in calculating the value of unknown resistance.
(iii) Generally alloys magnin/constantan/nichrome are used in Meter Bridge, because these materials have low temperature coefficient of resistivity.
Teacher's Note: Thick strips have negligible resistance, central balance minimises percentage error, and alloy wire has low temperature coefficient.
Exam Note: Answer all three parts separately.
Question 4. Name the charge carriers of electric current in (i) Silver foil (ii) Hydrogen discharge tube (iii) Germanium semiconductor (iv) Wire made of alloy nichrome (v) Superconductor
Solution.
(i) Charge carriers in silver foil are free electrons.
(ii) Charge carriers in hydrogen discharge tube are electrons (e–) and positive hydrogen ions (H+).
(iii) Charge carriers in germanium semiconductor are electrons (e–) and holes (o+)
(iv) Charge carriers in nichrome wire are electrons.
(v) Charge carriers in superconductor are electrons.
Teacher's Note: Carriers are electrons in metals, electrons with ions in gas discharge, and electrons with holes in semiconductors.
Exam Note: List carriers material by material.
Question 5. Electrons are continuously in motion within a conductor but there is no current in it unless some source of potential is applied across its ends. Give reason.
Solution.
In the absence of any external source the motion of electrons in a conductor is random and electrons collide continuously with the positive ions of metal. This causes a random change in direction of motion. The average velocity of random motion of electrons in any direction is zero, hence current is zero.
Teacher's Note: Without applied potential, electron motion is random, so net drift and current are zero.
Exam Note: Mention random motion, zero average velocity.
Question 6. Why is Wheatstone bridge (Metre Bridge) method not suitable for measurement of very low and very high resistances?
Solution.
Because, in order to ensure sensitivity of the bridge, all other resistances used should either have low value or very high value. This also requires a galvanometer of very low resistance or very high resistance and introduces error in the results.
Teacher's Note: The bridge loses sensitivity when resistances differ greatly, so extreme values give errors.
Exam Note: Mention sensitivity loss and error.
Question 7. Sketch a graph showing the variation of resistivity of carbon with temperature. OR Plot a graph showing temperature dependence of resistivity for a typical semiconductor. How is this behaviour explained? [CBSE Delhi 2012, (F) 2011]
Solution.
The resistivity of a typical semiconductor (carbon) decreases with increase of temperature. The graph is shown in the figure.
Explanation: In a semiconductor the number density of free electrons (n) increases with increase in temperature (T) and consequently the relaxation time decreases. But the effect of increase in n has a higher impact than the decrease of τ. So, resistivity decreases with increase in temperature.
Teacher's Note: Carbon and semiconductors: more charge carriers at higher temperature outweigh the shorter relaxation time, so resistivity falls.
Exam Note: Resistivity decreases with temperature; n increases more than τ falls.
Question 8. (a) You are required to select a carbon resistor of resistance 47 kΩ ± 10% from a large collection. What should be the sequence of colour bands used to code it? (b) Write the characteristics of manganin which make it suitable for making standard resistance. [CBSE (F) 2011]
Solution.
(a) Resistance = 47 kΩ ± 10% = 47 × 103 Ω ± 10%
Sequence of colour should be: Yellow, Violet, Orange and Silver.
(b) (i) Very low temperature coefficient of resistance.
(ii) High resistivity.
Teacher's Note: Digits 4 (yellow), 7 (violet), multiplier 103 (orange), tolerance 10% (silver).
Exam Note: Yellow, Violet, Orange, Silver; manganin has low temperature coefficient.
Question 9. Plot a graph showing variation of voltage Vs the current drawn from the cell. How can one get information from this plot about the emf of the cell and its internal resistance? [CBSE (F) 2016]
Solution.
V = ε − Ir ⇒ r = (ε − V)/I
At I = 0, V = ε.
When V = 0, I = I0 and r = ε/I0.
The intercept on the y-axis gives the emf of the cell. The slope of the graph gives the internal resistance.
Teacher's Note: From V = ε − Ir the line has intercept ε on the V-axis and magnitude of slope r.
Exam Note: Intercept = emf; magnitude of slope = internal resistance.
Question 10. Two cells of emfs 1.5 V and 2.0 V having internal resistances 0.2 Ω and 0.3 Ω respectively are connected in parallel. Calculate the emf and internal resistance of the equivalent cell. [CBSE Delhi 2016]
Solution.
E1 = 1.5 V, r1 = 0.2 Ω; E2 = 2.0 V, r2 = 0.3 Ω
emf of equivalent cell, E = (E1r2 + E2r1)/(r1 + r2) = (1.5 × 0.3 + 2.0 × 0.2)/(0.2 + 0.3) = (0.45 + 0.40)/0.5 V = 1.7 V
Internal resistance: 1/r = 1/r1 + 1/r2 ⇒ r = r1r2/(r1 + r2) = (0.2 × 0.3)/(0.2 + 0.3) Ω = 0.06/0.5 Ω = 0.12 Ω
Teacher's Note: Cells in parallel with same polarity: E = (E1r2 + E2r1)/(r1 + r2); r = r1r2/(r1 + r2).
Exam Note: E = 1.7 V, r = 0.12 Ω.
Question 11. When 5 V potential difference is applied across a wire of length 0.1 m, the drift speed of electrons is 2.5 × 10−4 m/s. If the electron density in the wire is 8 × 1028 m−3, calculate the resistivity of the material of wire. [CBSE (North) 2016]
Solution.
We know I = neAvd, I = V/R and R = ρl/A.
So V/R = neAvd ⇒ V/(RA) = nevd ⇒ V/(ρl) = nevd ⇒ ρ = V/(nevdl)
ρ = 5/(8 × 1028 × 1.6 × 10−19 × 2.5 × 10−4 × 0.1) Ωm = 1.56 × 10−5 Ωm ≈ 1.6 × 10−5 Ωm
Teacher's Note: Combine I = neAvd with Ohm's law and R = ρl/A so that area cancels, giving ρ = V/(nevdl).
Exam Note: ρ ≈ 1.6 × 10−5 Ωm.
Question 12. Two conducting wires X and Y of same diameter but different materials are joined in series across a battery. If the number density of electrons in X is twice that in Y, find the ratio of drift velocity of electrons in the two wires. [CBSE (AI) 2011]
Solution.
In series the current is the same, so IX = IY = I = neAvd.
For the same diameter, the cross-sectional area is the same: AX = AY = A.
∴ nxeAvx = nyeAvy
Given nx = 2ny ⇒ vx/vy = ny/nx = ny/2ny = 1/2
Teacher's Note: Same current and area in series mean drift velocity is inversely proportional to electron density.
Exam Note: vx : vy = 1 : 2.
Question 13. A conductor of length ‘l’ is connected to a dc source of potential ‘V’. If the length of the conductor is tripled by gradually stretching it, keeping ‘V’ constant, how will (i) drift speed of electrons and (ii) resistance of the conductor be affected? Justify your answer. [CBSE (F) 2012]
Solution.
(i) We know that vd = eVτ/(ml) ∝ 1/l. When the length is tripled, the drift velocity becomes one-third.
(ii) R = ρl/A, l′ = 3l. On stretching, the volume remains constant, so A′ = A/3.
New resistance R′ = ρl′/A′ = ρ × 3l/(A/3) = 9R
Hence, the new resistance will be 9 times the original.
Teacher's Note: Drift speed depends on the field V/l; stretching also reduces area to A/3 because volume stays constant.
Exam Note: Drift speed becomes 1/3; resistance becomes 9R.
Question 14. A potential difference V is applied across the ends of copper wire of length l and diameter D. What is the effect on drift velocity of electrons if (i) V is halved, (ii) l is doubled, (iii) D is halved? [CBSE Ajmer 2015]
Solution.
Drift velocity, vd = I/(neA) = (V/R)/(neA) = V/(neA(ρl/A)) = V/(neρl)
(i) As vd ∝ V, when V is halved the drift velocity is halved.
(ii) As vd ∝ 1/l, when l is doubled the drift velocity is halved.
(iii) As vd is independent of D, when D is halved the drift velocity remains unchanged.
Teacher's Note: Area cancels in vd = V/(neρl), so only V and l matter, not diameter.
Exam Note: Halved, halved, unchanged.
Question 15. Estimate the average drift speed of conduction electrons in a copper wire of cross-sectional area 1.0 × 10−7 m2 carrying a current of 1.5 A. Assume the density of conduction electrons to be 9 × 1028 m−3. [CBSE (AI) 2014]
Solution.
Flow of current in the conductor due to drift velocity of the free electrons is given by I = neAvd.
vd = I/(neA) = 1.5/(9 × 1028 × 1.6 × 10−19 × 1.0 × 10−7)
= 1.04 × 10−3 m/s ≈ 1 mm/s
Teacher's Note: Direct substitution in vd = I/(neA); drift speed is tiny despite a large current.
Exam Note: vd ≈ 1.0 × 10−3 m/s.
Question 16. In the circuit shown in the figure, find the total resistance of the circuit and the current in the arm CD. [CBSE (F) 2014]
Solution.
Resistances BC and CD are in series and their combination is in parallel with AD.
RBCD = 3 + 3 = 6 Ω. Then 1/RP = 1/6 + 1/3 ⇒ RP = 2 Ω
DF is in series with this combination: total resistance = 2 + 3 = 5 Ω (due to the capacitor, the 3 Ω resistor in EF will not be counted, as no steady current flows through it).
Total current = 15/5 = 3 A. This current gets divided at junction A.
Voltage across DF = 3 Ω × 3 A = 9 V and voltage across AD = 15 − 9 = 6 V.
Current in arm CD = 6 V/(3 + 3) Ω = 1 A.
Teacher's Note: A capacitor blocks steady current, so branch BCE carries nothing beyond the capacitor; reduce the remaining network stepwise.
Exam Note: Total resistance 5 Ω; current in CD = 1 A.
Question 17. Use Kirchhoff’s laws to determine the value of current I1 in the given electrical circuit. [CBSE Delhi 2007]
Solution.
Note on the figure: the figure printed with this question in the source is the capacitor circuit of the previous question and does not match the equations of the solution. The equations describe a circuit of three branches joining two junctions C and X: a 20 Ω resistor carrying I1, a 20 Ω resistor in series with an 80 V cell carrying I2, and a 40 Ω resistor in series with a 40 V cell carrying I3. This circuit is drawn above.
From Kirchhoff’s first law at junction C: I3 = I1 + I2 ...(i)
Applying Kirchhoff’s second law to the loop through the 20 Ω and the 40 Ω (40 V) branches: 40I3 − 40 + 20I1 = 0, or 20(2I3 + I1) = 40 ⇒ I1 + 2I3 = 2 ...(ii)
Applying Kirchhoff’s second law to the loop through the 80 V and the 20 Ω (I1) branches: 80 − 20I2 + 20I1 = 0 ⇒ 20(I1 − I2) = −80 ⇒ I2 − I1 = 4 ...(iii)
Substituting the value of I3 from (i) in (ii), we get I1 + 2(I1 + I2) = 2 ⇒ 3I1 + 2I2 = 2 ...(iv)
Multiplying equation (iii) by 2, we get 2I2 − 2I1 = 8 ...(v)
Subtracting (v) from (iv), we get 5I1 = −6 ⇒ I1 = −6/5 A = −1.2 A.
The negative sign shows that the current in the 20 Ω branch actually flows opposite to the direction assumed, i.e., 1.2 A from C to X. (Also I2 = 2.8 A and I3 = 1.6 A, which satisfy (i) and (ii).)
Teacher's Note: Two loop equations plus the junction rule give three unknown currents; a negative result only means the assumed direction was reversed.
Exam Note: I1 = −1.2 A: magnitude 1.2 A, reversed direction.
Question 18. Find the magnitude and direction of current in the 1 Ω resistor in the given circuit. [CBSE (South) 2016]
Solution.
Let I1 flow in mesh APQBA and I2 in mesh PCDQP, so the current in the 1 Ω resistor (P to Q) is I2 − I1.
For the mesh APQBA: −6 − 1(I2 − I1) + 3I1 = 0 or −I2 + 4I1 = 6 …(1)
For the mesh PCDQP: 2I2 − 9 + 3I2 + 1(I2 − I1) = 0 or 6I2 − I1 = 9 …(2)
Solving (1) and (2): I1 = 45/23 A and I2 = 42/23 A.
Current through the 1 Ω resistor = I2 − I1 = −3/23 A.
Magnitude = 3/23 A ≈ 0.13 A; the negative sign shows it flows from Q to P (opposite to the assumed direction).
Teacher's Note: Write loop equations with currents I1 and I2; the shared 1 Ω resistor carries their difference.
Exam Note: 3/23 A, from Q to P.
Question 19. In the circuit shown in the figure, find the total resistance of the circuit and the current in the arm AD. [CBSE (AI) 2014]
Solution.
Since BC and CD are in series, RBCD = 3 Ω + 3 Ω = 6 Ω. Also AD is in parallel with the combination of BC and CD.
1/RP = 1/6 + 1/3 = (6 + 3)/(6 × 3) ⇒ RP = 2 Ω
Then DF is in series: Req = 2 + 3 = 5 Ω (the capacitor branch carries no steady current).
Net current I = V/Req = 15/5 = 3 A.
Voltage across DF = 3 × 3 = 9 V, so voltage across the parallel part = 15 − 9 = 6 V.
∴ IAD = 6/3 = 2 A.
Teacher's Note: Same network: reduce to 5 Ω, then split the 3 A between the two arms.
Exam Note: Total resistance 5 Ω; IAD = 2 A.
Question 20. Figure shows two circuits each having a galvanometer and a battery of 3 V. When the galvanometers in each arrangement do not show any deflection, obtain the ratio R1/R2. [CBSE (AI) 2013]
Solution.
For a balanced Wheatstone bridge, no current flows through the galvanometer.
First circuit: 4/R1 = 6/9 ⇒ R1 = (4 × 9)/6 = 6 Ω
Second circuit: 6/12 = R2/8 ⇒ R2 = (6 × 8)/12 = 4 Ω
∴ R1/R2 = 6/4 = 3/2
Teacher's Note: Zero deflection means a balanced bridge: ratio of arms on one side equals the other.
Exam Note: R1/R2 = 3/2.
Question 21. A potentiometer wire of length 1 m has a resistance of 10 Ω. It is connected to a 6 V battery in series with a resistance of 5 Ω. Determine the emf of the primary cell which gives a balance point at 40 cm. [CBSE Delhi 2014]
Solution.
Here, l = 1 m, R1 = 10 Ω, V = 6 V, R2 = 5 Ω.
Current in the potentiometer wire: I = V/(R1 + R2) = 6/(10 + 5) = 0.4 A
Potential drop across the wire: V′ = IR1 = 0.4 × 10 = 4 V
Potential gradient, K = V′/l = 4/1 = 4 V/m
emf of the primary cell = K × 0.4 m = 4 × 0.4 = 1.6 V
Teacher's Note: First find the current through the wire, then the potential gradient, then multiply by balance length.
Exam Note: emf = 1.6 V.
Question 22. In the potentiometer circuit shown, the null point is at X. State with reason, where the balance point will be shifted when: (a) Resistance R is increased, keeping all other parameters unchanged; (b) Resistance S is increased, keeping R constant. [CBSE Bhubaneshwar 2015]
Solution.
Let l be the balance length of the segment AX on the potentiometer wire for given resistance R and S.
(a) If resistance R is increased, the current in the main circuit (wire AB) decreases. From K = ρI/A the potential gradient along the wire AB decreases. To balance the emf of the cell, the point X will shift toward the point B, i.e., ε = kl = k′l′; if k′ < k, then l′ > l.
(b) For the given resistance R, the potential gradient along the wire remains the same, so the balance length l remains constant (ε = kl). No current flows in the resistance S at balance, so increasing or decreasing S causes no change in the balance length.
Teacher's Note: Balance length = emf/potential gradient; R changes the gradient, but S carries no current at the null point.
Exam Note: (a) Shifts toward B; (b) no change.
Question 23. Two students X and Y perform an experiment on potentiometer separately using the circuit diagram shown here. Keeping other things unchanged (i) X increases the value of resistance R. (ii) Y decreases the value of resistance S in the set up. How would these changes affect the position of the null point in each case and why? [CBSE (South) 2016] [HOTS]
Solution.
(i) By increasing resistance R, the current in the main circuit decreases, so the potential gradient decreases. Hence a greater length of wire would be needed for balancing the same potential difference. So, the null point would shift towards right (i.e., towards B).
(ii) By decreasing resistance S, the terminal potential difference V = ε − Ir, where I = ε/(r + S), i.e. V = ε/(1 + r/S), across the cell decreases, so balance is obtained at a smaller length. So, the null point would shift towards left (i.e., towards A).
Teacher's Note: Null length = voltage balanced/gradient; R changes the gradient, S changes the cell’s terminal voltage.
Exam Note: (i) Towards B; (ii) towards A.
Question 24. Two students ‘X’ and ‘Y’ perform an experiment on potentiometer separately using the circuit given. Keeping other parameters unchanged, how will the position of the null point be affected if (i) ‘X’ increases the value of resistance R in the set-up by keeping the key K1 closed and the key K2 open? (ii) ‘Y’ decreases the value of resistance S in the set-up, while the key K2 remain open and the key K1 closed? Justify your answer in each case. [CBSE (F) 2012] [HOTS]
Solution.
(i) By increasing resistance R the current through AB decreases, so the potential gradient decreases. Hence a greater length of wire would be needed for balancing the same potential difference. So the null point would shift towards B.
(ii) By decreasing resistance S, the current through AB remains the same, so the potential gradient does not change. As K2 is open there is no effect of S on the null point.
Teacher's Note: With K2 open the cell is on open circuit, so S has no effect; only R alters the potential gradient.
Exam Note: (i) Towards B; (ii) no change.
Question 25. What will be the value of current through the 2 Ω resistance for the circuit shown in the figure? Give reason to support your answer. [CBSE (F) 2013] [HOTS]
Solution.
No current will flow through the 2 Ω resistor, because in a closed loop, the total p.d. must be zero. So
10 V − 5I1 = 0 …(1)
20 V − 10I2 = 0 …(2)
And the resistor 2 Ω is not part of any loop ABCD and EFGH. (I1 = 2 A and I2 = 2 A; the current in the 2 Ω resistor is zero.)
Teacher's Note: The 2 Ω resistor joins two otherwise separate loops, so it forms no closed path and carries no current.
Exam Note: Current through 2 Ω is zero.
Question 26. Using Kirchhoff’s rules determine the value of unknown resistance R in the circuit so that no current flows through 4 Ω resistance. Also find the potential difference between A and D. [CBSE Delhi 2012] [HOTS]
Solution.
Applying Kirchhoff’s loop rule for loop ABEFA,
−9 + 6 + 4 × 0 + 2I = 0
⇒ I = 1.5 A …(i)
For loop BCDEB,
3 + IR + 4 × 0 − 6 = 0
∴ IR = 3
Putting the value of I from (i), (3/2) × R = 3 ⇒ R = 2 Ω
Potential difference between A and D through path ABCD:
9 − 3 − IR = VAD
or 9 − 3 − (3/2) × 2 = VAD ⇒ VAD = 3 V
Teacher's Note: With zero current in the 4 Ω branch, the left loop fixes I; the right loop then gives R.
Exam Note: R = 2 Ω; VAD = 3 V.
Question 27. Calculate the value of the resistance R in the circuit shown in the figure so that the current in the circuit is 0.2 A. What would be the potential difference between points B and E? [CBSE (AI) 2012] [HOTS]
Solution.
Here, RBCD = 5 Ω + 10 Ω = 15 Ω
Effective resistance between B and E:
1/RBE = 1/30 + 1/10 + 1/15 ⇒ RBE = 5 Ω
Applying Kirchhoff’s law:
5 × 0.2 + R × 0.2 + 15 × 0.2 = 8 − 3 ⇒ R = 5 Ω
Hence, VBE = IRBE = 0.2 × 5 = 1 volt
Teacher's Note: Reduce the three parallel paths between B and E to 5 Ω, then write one loop equation.
Exam Note: R = 5 Ω; VBE = 1 V.
Question 28. In the circuit shown in the figure, the galvanometer ‘G’ gives zero deflection. If the batteries A and B have negligible internal resistance, find the value of the resistor R. [CBSE (F) 2013] [HOTS]
Solution.
If galvanometer G gives zero deflection, then current of the source of 12 V flows through R, and the voltage across R becomes 2 V.
Current in the circuit I = ε/(R1 + R2) = 12/(500 + R)
and V = IR = 2
(12.0 V/(500 + R)) R = 2
12R = 1000 + 2R
10R = 1000
⇒ R = 100 Ω
Teacher's Note: No galvanometer current means the 2 V cell exactly balances the potential drop across R in the 12 V loop.
Exam Note: R = 100 Ω.
Question 29. The plot of the variation of potential difference across a combination of three identical cells in series, versus current is shown alongside. What is the emf and internal resistance of each cell? [CBSE (Central) 2016] [HOTS]
Solution.
We know that for a circuit V = Eeq − Ireq …(i)
From the graph, when I = 0 A, then V = 6 V and when I = 1 A then V = 0 V.
Putting V = 6 V and I = 0 A in eq. (i): 6 = Eeq − 0 · req ⇒ Eeq = 6 V
Eeq = ε1 + ε2 + ε3 ⇒ ε1 = ε2 = ε3 = ε = E/3 = 2 V
And, when I = 1 A and V = 0 V: 0 = 6 − 1 · req ⇒ req = 6 Ω
req = r1 + r2 + r3 ⇒ r1 = r2 = r3 = r = R/3 = 2 ohm
Teacher's Note: Intercept on V-axis gives total emf and intercept on I-axis gives short-circuit current; divide both by three cells in series.
Exam Note: Each cell: 2 V, 2 Ω.
Question 30. Write the mathematical relation between mobility and drift velocity of charge carriers in a conductor. Name the mobile charge carriers responsible for conduction of electric current in (i) an electrolyte (ii) an ionised gas.
Solution.
The mathematical relation between mobility and drift velocity of charge carriers in a conductor is given by μ = |vd|/E = (magnitude of the drift velocity)/(electric field).
(i) In an electrolyte, the mobile charge carriers are both positive and negative ions.
(ii) In an ionised gas, the mobile charge carriers are electrons and positive ions.
Teacher's Note: Mobility is drift speed per unit field; electrolytes conduct by ions, gases by electrons and ions.
Exam Note: μ = vd/E; ions in electrolyte; electrons and ions in gas.
Question 31. In a Wheatstone’s bridge experiment, a student by mistake, connects key (K) in place of galvanometer and galvanometer (G) in place of key (K). What will be the test for the balance of the bridge?
Solution.
When the bridge is balanced, there will be no current in key, therefore a constant current will flow in the galvanometer. In balanced position, there will be a constant deflection in galvanometer and hence no change in its deflection on pressing the key.
Teacher's Note: At balance the key branch carries no current, so pressing it cannot change the galvanometer.
Exam Note: Balance: galvanometer deflection unchanged on pressing key.
Question 32. The given circuit represents a balanced Wheatstone’s bridge. Calculate the value of resistance x.
Solution.
In the balanced condition, P/Q = R/S
∴ (4 + 4)/1 = (4 + x)/2 ⇒ x = 12 Ω
Teacher's Note: Two 2 Ω in parallel give 1 Ω, two 4 Ω give 2 Ω; then apply the balance condition.
Exam Note: x = 12 Ω.
Question 33. Two electric bulbs have the following specifications. (i) 100 W at 220 V (ii) 1000 W at 220 V. Which bulb has higher resistance? What is the ratio of their resistances?
Solution.
The resistance of filament, R = V/I = V2/P
At constant voltage V, the resistance R ∝ 1/P
That is, the resistance of the filament of the 100 W bulb is greater than that of the 1000 W bulb.
The ratio of resistances = R1/R2 = P2/P1 = 1000/100 = 10/1 = 10 : 1
Teacher's Note: Both bulbs run at 220 V, so R = V2/P and the lower-power bulb has the larger resistance.
Exam Note: 100 W bulb has more resistance; ratio 10 : 1.
Question 34. Two heated wires of the same dimensions are first connected in series and then in parallel to a source of supply. What will be the ratio of heat produced in the two cases?
Solution.
Q = (V2/R) t ∝ 1/R
For same voltage, Qseries/Qparallel = Rparallel/Rseries = [(R · R)/(R + R)]/(R + R) = (R/2)/(2R) = 1/4
Teacher's Note: At fixed supply voltage heat is inversely proportional to resistance; parallel gives R/2 and series gives 2R.
Exam Note: Heat ratio series : parallel = 1 : 4.
Question 35. A heater coil is cut in two parts and only one of them is used in the heater. What is the ratio of the heat produced by this half coil to that by the original coil if the voltage applied is the same?
Solution.
For same p.d. the heat produced per second H = V2/R ∝ 1/R.
As the one part of heater coil has resistance R2 = R/2, R being the resistance of the original coil, the ratio of heat produced is
H2/H1 = R1/R2 = R/(R/2) = 2 : 1
Teacher's Note: Cutting the coil in half halves its resistance, so at the same voltage the heat rate doubles.
Exam Note: Half coil : original = 2 : 1.
Question 36. Two wires A and B of the same material and having same length, have their cross sectional areas in the ratio 1 : 6. What would be the ratio of heat produced in these wires when same voltage is applied across each? [CBSE Sample Paper 2017]
Solution.
AA : AB = 1 : 6
H = V2t/R and R = ρl/A
HA = V2t/(ρl/AA); HB = V2t/(ρl/AB)
HA/HB = (V2t × AA/ρl) × (ρl/V2tAB) ⇒ HA/HB = AA/AB = 1 : 6
Teacher's Note: For equal voltage, length and material, heat is proportional to cross-sectional area because R falls as area rises.
Exam Note: HA : HB = 1 : 6.
Question 37. A (i) series (ii) parallel combination of two given resistors is connected, one by one, across a cell. In which case will the terminal potential difference, across the cell have a higher value?
Solution.
Terminal potential difference across a cell V = ε − Ir
(i) In series arrangement, current IS = E/(R1 + R2 + r)
(ii) In parallel arrangement, current IP = E/(R1R2/(R1 + R2) + r)
Obviously, IP > IS, so VP < VS
That is, the series arrangement will have the higher terminal potential difference.
Teacher's Note: Parallel resistors draw more current, so more voltage is lost across the internal resistance.
Exam Note: Series arrangement gives higher terminal p.d.
Question 38. A voltage of 30 V is applied across a carbon resistor with first, second and third rings of blue, black and yellow colours respectively. Calculate the value of current in mA, through the resistor.
Solution.
Value of first digit (blue ring) = 6
Value of second digit (black ring) = 0
Multiplier (yellow ring) = 104
∴ Resistance, R = 60 × 104 Ω, Voltage, V = 30 V
Current I = V/R = 30/(60 × 104) = 0.5 × 10−4 A = 0.05 mA.
Teacher's Note: Blue = 6, black = 0, yellow = 104 give 600 kΩ; then apply Ohm’s law.
Exam Note: R = 600 kΩ; I = 0.05 mA.
Question 39. n-identical cells, each of emf ε, internal resistance r connected in series are charged by a dc source of emf ε′ using a resistance R. (i) Draw the circuit arrangement. (ii) Deduce expressions for (a) the charging current and (b) the potential difference across the combination of cells.
Solution.
The circuit arrangement is shown in the figure.
Applying Kirchhoff’s second law to the circuit abcda:
−nε − I(nr) − IR + ε′ = 0 ⇒ I = (ε′ − nε)/(R + nr)
(a) Charging current, I = (ε′ − nε)/(R + nr) …(i)
(b) Potential difference across the combination V is given by −V − IR + ε′ = 0
⇒ V = ε′ − IR = ε′ − R(ε′ − nε)/(R + nr)
⇒ V = [ε′(R + nr) − ε′R + nεR]/(R + nr) = n(ε′r + εR)/(R + nr)
Teacher's Note: Charging emf must exceed nε; the net emf (ε′ − nε) drives current through R + nr.
Exam Note: I = (ε′ − nε)/(R + nr).
Question 40. Two cells of emf 10 V and 2 V and internal resistance 10 Ω and 5 Ω respectively, are connected in parallel as shown. Find the effective voltage across R. [CBSE Sample Paper 2016]
Solution.
The effective voltage across R is given by
εeq = (ε1/r1 − ε2/r2)/(1/r1 + 1/r2) = (10/10 − 2/5)/(1/10 + 1/5)
⇒ εeq = 2 V
Teacher's Note: The cells are connected with opposite polarity, so their terms in the numerator subtract: (1 − 0.4)/0.3.
Exam Note: Opposing cells: εeq = 2 V.
Question 41. A resistance R = 4 Ω is connected to one of the gaps in a meter bridge, which uses a wire of length 1 m. An unknown resistance X > 4 Ω is connected in the other gap as shown in the figure. The balance point is noticed at ‘l’ cm from the positive end of the battery. On interchanging R and X, it is found that the balance point further shifts by 20 cm (away from the end A). Neglecting the end correction calculate the value of unknown resistance ‘X’ used.
Solution.
From the ‘meter bridge’ formula R/X = l/(100 − l) ⇒ X = [(100 − l)/l] R
Given R = 4 Ω, ∴ X = [(100 − l)/l] × 4 Ω …(i)
On interchanging R and X, the balance point is obtained at a distance (l + 20) cm from end A, so
X/R = (l + 20)/(100 − (l + 20)) ⇒ X = [(l + 20)/(80 − l)] × 4 Ω …(ii)
Equating (i) and (ii): [(100 − l)/l] × 4 = [(l + 20)/(80 − l)] × 4
Solving we get l = 40 cm
∴ Unknown resistance, X = [(100 − l)/l] × 4 Ω = [(100 − 40)/40] × 4 Ω ⇒ X = 6 Ω
Teacher's Note: Write the meter bridge condition before and after interchange, equate the two expressions for X to find l, then substitute.
Exam Note: l = 40 cm; X = 6 Ω.
Question 42. Two primary cells of emfs ε1 and ε2 (ε1 > ε2) are connected to a potentiometer wire AB as shown in fig. If the balancing lengths for the two combinations of the cells are 250 cm and 400 cm, find the ratio of ε1 and ε2.
Solution.
In the first combination ε1 and ε2 are opposing each other while in the second combination ε1 and ε2 are adding each other, so
ε1 − ε2 = kl1
ε1 + ε2 = kl2
(ε1 − ε2)/(ε1 + ε2) = l1/l2 = 250/400 = 5/8
⇒ 8ε1 − 8ε2 = 5ε1 + 5ε2 ⇒ 3ε1 = 13ε2
∴ ε1/ε2 = 13/3, i.e. ε1 : ε2 = 13 : 3
Teacher's Note: Opposing cells balance at the shorter length (difference of emfs), aiding cells at the longer length (sum of emfs).
Exam Note: ε1 : ε2 = 13 : 3.
Question 43. A cylindrical metallic wire is stretched to increase its length by 10%. Calculate the percentage increase in its resistance. [HOTS]
Solution.
When the same wire is stretched, its length increases but the cross-sectional area decreases. The change in resistance is due to both the increase in length and the decrease in cross-sectional area.
Volume V = lA = constant, A = V/l = constant
∴ R = ρl/A = ρl2/V ∝ l2
∴ R′/R = (l′/l)2
Given l′ = l + (10/100)l = 1.1l ⇒ l′/l = 1.1
R′/R = (1.1)2 = 1.21
% increase in resistance = [(R′ − R)/R] × 100% = (R′/R − 1) × 100% = (1.21 − 1) × 100% = 21%
Teacher's Note: Stretching at constant volume makes resistance proportional to length squared, so a 10% increase in length gives about 21%.
Exam Note: 21% increase (R ∝ l2).
Question 44. You are given n resistors each of resistance r. They are first connected to get the minimum possible resistance. In the second case, these are again connected differently to get the maximum possible resistance. Calculate the ratio between minimum and maximum values of resistance so obtained. [HOTS]
Solution.
For minimum possible resistance, the resistors should be connected in parallel:
1/rP = 1/r + 1/r + … n times = n/r ⇒ rP = r/n
For maximum possible resistance, the resistors should be connected in series:
rS = r + r + … n times = nr
Ratio rP/rS = (r/n) × (1/nr) = 1/n2
Teacher's Note: Parallel gives the smallest combination r/n, series the largest nr; divide to get 1/n2.
Exam Note: rmin : rmax = 1 : n2.
Question 45. For the potentiometer circuit shown in the given figure, points X and Y represent the two terminals of an unknown emf E′. A student observed that when the jockey is moved from the end A to the end B of the potentiometer wire, the deflection in the galvanometer remains in the same direction. What may be the two possible faults in the circuit that could result in this observation? If the galvanometer deflection at the end B is (i) more, (ii) less than at the end A, which of the two faults, listed above, would be there in the circuit? Give reason in support of your answer in each case. [HOTS]
Solution.
The two possible faults in the circuit may be (i) emf E′ is greater than emf E. (ii) Terminal X of unknown emf is negative (while it should be positive).
If the galvanometer deflection at end B is more than that at end A, then terminal X is negative, because in this case the net current in the galvanometer along AB due to both cells is additive.
If the galvanometer deflection at end B is less than that at end A, then E′ > E, because the net current in the galvanometer due to both cells’ emfs E and E′ is subtractive.
Teacher's Note: No null point appears when E′ exceeds E or when the test cell is connected with reversed polarity.
Exam Note: Faults: E′ > E, or X negative.
Question 46. The following circuit shows the use of potentiometer to measure the internal resistance of a cell. (i) When the key is open, how does the balance point change, if the current from the driver cell decreases? (ii) When the key K is closed, how does the balance point change if R is increased keeping current from the driver cell constant? [HOTS]
Solution.
(i) When the current through the driver cell decreases, the potential gradient across the potentiometer wire decreases; so the balancing length l = E/k increases, so the balance point is shifted to the right.
(ii) With increase of R, the terminal p.d. across cell E increases and hence the balancing length l = V/k ∝ V increases. So the balance point is shifted to the right.
Teacher's Note: Balancing length is (voltage to balance)/(gradient): smaller gradient or larger terminal voltage both lengthen it.
Exam Note: Both cases: balance point shifts right.
Question 47. First a set of n equal resistors of R each are connected in series to a battery of emf E and internal resistance R. A current I is observed to flow. Then the n resistors are connected in parallel to the same battery. It is observed that the current is increased 10 times. What is n? [NCERT Exemplar] [HOTS]
Solution.
When n resistors are in series, I = E/(R + nR);
When n resistors are in parallel, E/(R + R/n) = 10I
(1 + n)/(1 + 1/n) = 10 ⇒ [(1 + n)/((n + 1)/n)] = 10 ⇒ n = 10.
Teacher's Note: Write both currents including the battery’s internal resistance R; the ratio simplifies directly to n.
Exam Note: n = 10.
Question 48. Two cells of same emf E but internal resistance r1 and r2 are connected in series to an external resistor R (Fig.). What should be the value of R so that the potential difference across the terminals of the first cell becomes zero. [NCERT Exemplar] [HOTS]
Solution.
I = (E + E)/(R + r1 + r2)
V1 = E − Ir1 = E − [2E/(r1 + r2 + R)] r1 = 0
or E = 2Er1/(r1 + r2 + R)
⇒ r1 + r2 + R = 2r1 ⇒ R = r1 − r2
Teacher's Note: Set the first cell’s terminal voltage E − Ir1 to zero, with I from the series emf 2E.
Exam Note: R = r1 − r2.
Question 49. Calculate the temperature at which the resistance of a conductor becomes 20% more than its resistance at 27°C. The value of the temperature coefficient of resistance of the conductor is 2.0 × 10−4/K. [HOTS]
Solution.
Given R27 = R (say), RT = R + (20/100)R = 1.2R, T1 = 27 + 273 = 300 K
From the relation, RT = R27[1 + α(T2 − 300)]
⇒ 1.2R = R[1 + 2.0 × 10−4(T2 − 300)]
⇒ 1 + 2.0 × 10−4(T2 − 300) = 1.2
or 2.0 × 10−4(T2 − 300) = 0.2
T2 − 300 = 0.2/(2.0 × 10−4) = 1000
T2 = 1000 + 300 = 1300 K
Teacher's Note: Use RT = R0(1 + αΔT) with a 0.2 fractional rise and convert the starting 27°C to 300 K.
Exam Note: T = 1300 K (1027°C).
Question 50. The potential difference across a resistor ‘r’ carrying current ‘I’ is Ir. (i) Now if the potential difference across ‘r’ is measured using a voltmeter of resistance ‘RV’, show that the reading of voltmeter is less than the true value. (ii) Find the percentage error in measuring the potential difference by a voltmeter. (iii) At what value of RV, does the voltmeter measures the true potential difference? [CBSE Sample Paper 2016] [HOTS]
Solution.
(i) V = Ir (without voltmeter RV)
V′ = IrRV/(r + RV) = Ir/(1 + r/RV)
V′ < V
(ii) Percentage error = [(V − V′)/V] × 100 = [r/(r + RV)] × 100
(iii) RV → ∞, V′ = Ir = V
Teacher's Note: A voltmeter in parallel lowers the combined resistance and so the current-voltage drop; only an infinite RV reads true.
Exam Note: Error = r/(r + RV) × 100%; ideal RV = ∞.
Free study material for Physics
Download Xam Idea Solutions for Class 12 Math PDF
Chapter-wise Xam Idea Solutions: Xam Idea Solutions Class 12 Physics Chapter 3 Current Electricity Short Answer Questions I
Access the complete chapter-wise PDF for Xam Idea Solutions Class 12 Physics Chapter 3 Current Electricity Short Answer Questions I. These structured Xam Idea Solutions solutions for Class 12 Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Concept-Driven Math Answers
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Explore More Study Resources for Class 12 Math
In addition to these Xam Idea Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.