Xam Idea Solutions Class 12 Physics Chapter 3 Current Electricity Long Answer Questions

Download Class 12 Physics Textbook Solutions: Chapter 03 Current Electricity

Explore reliable textbook solutions for Chapter 03 Current Electricity tailored for Class 12 learners using methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.

Access Textbook Answers and Solutions

Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.

Long Answer Questions

Question 1. Derive an expression for drift velocity of free electrons in a conductor in terms of relaxation time of electrons. [CBSE Delhi 2009]
OR
Explain how the average velocity of free electrons in a metal at constant temperature, in an electric field, remains constant even though the electrons are being constantly accelerated by this electric field.

Solution.

Consider a metallic conductor XY of length l and cross-sectional area A. A potential difference V is applied across the conductor XY. Due to this potential difference an electric field E is produced in the conductor. The magnitude of electric field strength is E = V/l and its direction is from Y to X.

This electric field exerts a force on free electrons, due to which electrons are accelerated.

XY+++++EvdlV

The electric force on an electron is F = −eE (where e = 1.6 × 10−19 coulomb).

If m is the mass of the electron, then its acceleration is a = F/m = −eE/m   ...(i)

This acceleration remains constant only for a very short duration, since there are random forces which deflect the electron in a random manner. These deflections may arise as

(i) Ions of the metallic crystal vibrate simple harmonically around their mean positions. Different ions vibrate in different directions and may be displaced by different amounts.

(ii) Direct collisions of electrons with atoms of the metallic crystal lattice.

In any way, after a short duration called relaxation time, the motion of electrons becomes random. Thus, we can imagine that the electrons are accelerated only for a short duration. As the average velocity of random motion is zero, if we consider the average motion of an electron, then its initial velocity is zero, so the velocity of the electron after time τ (i.e., drift velocity vd) is given by the relation v = u + at.

Here u = 0, v = vd, t = τ, a = −eE/m, so

vd = 0 − (eE/m)τ  ⇒  vd = −(eτ/m)E

At a given temperature, the relaxation time τ remains constant, so the drift velocity remains constant.

Teacher's Note: Drift speed is acceleration times the average free time: vd = eEτ/m, opposite to the field for electrons.

Exam Note: vd = eEτ/m; τ is average time between collisions.

Question 2. Establish a relation between electric current and drift velocity. [CBSE (AI) 2013]
OR
Prove that the current density of a metallic conductor is directly proportional to the drift speed of electrons.

Solution.

Consider a uniform metallic wire XY of length l and cross-sectional area A. A potential difference V is applied across the ends X and Y of the wire. This causes an electric field at each point of the wire of strength E = V/l   ...(i)

Due to this electric field, the electrons gain a drift velocity vd opposite to the direction of the electric field. If q be the charge passing through the cross-section of the wire in t seconds, then current in the wire I = q/t   ...(ii)

XYPQ−−−−−−vd tEVI

The distance traversed by each electron in time t = average velocity × time = vdt.

If we consider two planes P and Q at a distance vdt in a conductor, then the total charge flowing in time t will be equal to the total charge on the electrons present within the cylinder PQ.

The volume of this cylinder = cross-sectional area × height = A vdt.

If n is the number of free electrons in the wire per unit volume, then the number of free electrons in the cylinder = n(A vdt).

If the charge on each electron is −e (e = 1.6 × 10−19 C), then the magnitude of the total charge flowing through a cross-section of the wire is q = (nA vdt)e = neA vdt   ...(iii)

∴ Current flowing in the wire, I = q/t, i.e., I = neA vd   ...(iv)

This is the relation between electric current and drift velocity. Since the carriers are electrons, the direction of the conventional current is opposite to the direction of the drift velocity.

∴ Current density, J = I/A = ne vd  ⇒  J ∝ vd.

That is, current density of a metallic conductor is directly proportional to the drift velocity.

Teacher's Note: Charge in the cylinder of length vdt crosses the plane in time t, giving I = neAvd.

Exam Note: I = neAvd; J = nevd, so J ∝ vd.

Question 3. Deduce Ohm’s law using the concept of drift velocity.
OR
Define the term ‘drift velocity’ of charge carriers in a conductor. Obtain the expression for the current density in terms of relaxation time. [CBSE (F) 2014]
OR
Define relaxation time of the free electrons drifting in a conductor. How is it related to the drift velocity of free electrons? Use this relation to deduce the expression for the electrical resistivity of the material. [CBSE (AI) 2012]
OR
(i) On the basis of electron drift, derive an expression for resistivity of a conductor in terms of number density of free electrons and relaxation time. On what factors does resistivity of a conductor depend?
(ii) Why alloys like constantan and manganin are used for making standard resistors? [CBSE Delhi 2016]

Solution.

Relaxation time of free electrons drifting in a conductor is the average time elapsed between two successive collisions. Drift velocity is the average velocity acquired by the free electrons in a conductor under the influence of an applied electric field.

Deduction of Ohm’s law: Consider a conductor of length l and cross-sectional area A. When a potential difference V is applied across its ends, the current produced is I. If n is the number of electrons per unit volume in the conductor and vd the drift velocity of electrons, then the relation between current and drift velocity (magnitude) is

I = neAvd   ...(i), where e = 1.6 × 10−19 C.

Electric field produced at each point of the wire, E = V/l   ...(ii)

If τ is the relaxation time and E is the electric field strength, then the drift velocity is vd = eτE/m   ...(iii)

Substituting this value in (i), we get I = neA(eτE/m) = (ne2τ/m)AE   ...(iv)

Current density, J = I/A = (ne2τ/m)E, which is the expression for the current density in terms of relaxation time.

As E = V/l [from (ii)], I = (ne2τA/m)(V/l), or V/I = (m/ne2τ)(l/A)   ...(v)

Current density in terms of the applied potential difference is J = (ne2τ/ml)V. Under given physical conditions (temperature, pressure), for a given conductor (m/ne2τ)(l/A) is a constant. This constant is called the resistance of the conductor (i.e., R).

i.e., R = (m/ne2τ)(l/A)   ...(vi)

From (v) and (vi): V/I = R   ...(vii)

This is Ohm’s law. From equation (vi) it is clear that the resistance of a wire depends on its length (l), cross-sectional area (A), number of electrons per m3 (n) and the relaxation time (τ).

Expression for resistivity: As R = ρl/A   ...(viii)

Comparing (vi) and (viii), we get the resistivity of a conductor ρ = m/(ne2τ)   ...(ix)

Clearly, resistivity of a conductor is inversely proportional to the number density of electrons and relaxation time.

Resistivity of the material of a conductor depends upon the relaxation time, i.e., temperature and the number density of electrons.

(ii) Alloys like constantan and manganin are used for making standard resistors because they show very weak dependence of resistivity on temperature.

XY+++++ElV

Teacher's Note: Ohm’s law drops out because m/(ne2τ)·l/A stays constant at fixed temperature.

Exam Note: R = m l/(ne2τA); ρ = m/(ne2τ).

Question 4. Derive condition of balance of a Wheatstone bridge.
OR
Draw a circuit diagram showing balancing of Wheatstone bridge. Use Kirchhoff’s rules to obtain the balance condition in terms of the resistances of four arms of Wheatstone bridge. [CBSE Delhi 2013, 2015]

Solution.

Condition of balance of a Wheatstone bridge: The circuit diagram of Wheatstone bridge is shown in the figure.

PQRSK2GBACDK1E

P, Q, R and S are four resistances forming a closed bridge, called Wheatstone bridge. A battery is connected across A and C, while a galvanometer is connected between B and D. When the bridge is balanced, there is no current in the galvanometer.

Derivation of formula: Let the current flowing in the circuit in the balanced condition be I. This current on reaching point A is divided into two parts I1 and I2. As there is no current in the galvanometer in balanced condition, current in resistances P and Q is I1 and in resistances R and S it is I2.

Applying Kirchhoff’s I law at point A: I − I1 − I2 = 0, or I = I1 + I2   ...(i)

Applying Kirchhoff’s II law to closed mesh ABDA: −I1P + I2R = 0, or I1P = I2R   ...(ii)

Applying Kirchhoff’s II law to mesh BCDB: −I1Q + I2S = 0, or I1Q = I2S   ...(iii)

Dividing equation (ii) by (iii), we get I1P/I1Q = I2R/I2S, or P/Q = R/S   ...(iv)

This is the condition of balance of Wheatstone bridge.

Teacher's Note: Zero galvanometer current makes B and D equipotential, so the same current I1 flows through P and Q.

Exam Note: Balance: P/Q = R/S, with no galvanometer current.

Question 5. Using the principle of Wheatstone Bridge, describe the method to determine the specific resistance of a wire in the laboratory. Draw the circuit diagram and write the formula used. Write any two important precautions you would observe while performing the experiment.
OR
Draw a circuit diagram of a Metre Bridge and write the mathematical relation used to determine the value of an unknown resistance. Why cannot such an arrangement be used for measuring very low resistance? [CBSE East 2016]
OR
(a) State, with the help of a suitable diagram, the principle on which the working of a meter bridge is based.
(b) Answer the following:
(i) Why are the connections between resistors in a meter bridge made of thick copper strips?
(ii) Why is it generally preferred to obtain the balance point near the middle of the bridge wire in meter bridge experiments? [CBSE (F) 2013]

Solution.

Metre Bridge: special case of Wheatstone bridge. It is a practical device based on the principle of Wheatstone bridge to determine the unknown resistance of a wire. If the ratio of arm resistors in a Wheatstone bridge is constant, then no current flows through the galvanometer (or bridge wire).

Construction: It consists of a uniform 1 metre long wire AC of constantan or manganin fixed along a scale on a wooden base. The ends A and C of the wire are joined to two L-shaped copper strips carrying connecting screws as shown. In between these copper strips, there is a third straight copper strip having three connecting screws. The middle screw D is connected to a sensitive galvanometer. The other terminal of the galvanometer is connected to a sliding jockey B. The jockey can be made to move anywhere parallel to wire AC.

Circuit: To find the unknown resistance S, the circuit is completed as shown in the figure. The unknown resistance wire of resistance S is connected across the gap between points C and D and a resistance box is connected across the gap between the points A and D. A cell, a rheostat and a key (K) are connected between the points A and C by means of connecting screws. In the experiment when the sliding jockey touches the wire AC at any point, the wire is divided into two parts. These two parts AB and BC act as the resistances P and Q of the Wheatstone bridge. In this way the resistances of arms AB, BC, AD and DC form the resistances P, Q, R and S of the Wheatstone bridge. Thus the circuit of the metre bridge is the same as that of the Wheatstone bridge.

ACRSDresistance boxGBPQl cm(100 − l) cmRhKcell

Method: To determine the unknown resistance, first of all key K is closed and a resistance R is taken out from the resistance box in such a way that on pressing the jockey B at the end points A and C, the deflection in the galvanometer is on both the sides. Now the jockey is slid on the wire to such a position that on pressing the jockey on the wire at that point, there is no deflection in the galvanometer G. In this position, the points B and D are at the same potential; therefore the bridge is balanced. The point B is called the null point. The lengths of both parts AB and BC of the wire are read on the scale. The condition of balance of Wheatstone bridge is P/Q = R/S

⇒ Unknown resistance, S = (Q/P)R   ...(i)

To determine specific resistance: If r is the resistance per cm length of wire AC and l cm is the length of wire AB, then the length of wire BC will be (100 − l) cm.

∴ P = resistance of wire AB = lr and Q = resistance of wire BC = (100 − l)r

Substituting these values in equation (i), we get S = [(100 − l)r/(lr)] × R, or S = [(100 − l)/l] R   ...(ii)

As the resistance R (from the resistance box) is known, the resistance S may be calculated. A number of observations are taken for different resistances taken in the resistance box and S is calculated each time and the mean value of S is found.

Knowing resistance S, radius r of the wire by screw gauge and length L of the wire by metre scale, the specific resistance is ρ = SA/L = Sπr2/L.

Why very low resistance cannot be measured: If a small resistance is to be measured, all other resistances used in the circuit, including the galvanometer, should be low to ensure sensitivity of the bridge. Also the resistance of thick copper strips and connecting wires (end resistances) becomes comparable to the resistance to be measured. This results in large error in measurement.

Precautions:

(i) In this experiment the resistances of the copper strips and connecting screws have not been taken into account. These resistances are called end-resistances. Therefore very small resistances cannot be found accurately by Metre Bridge. The resistance S should not be very small.

(ii) The current should not flow in the metre bridge wire for a long time, otherwise the wire will become hot and its resistance will be changed.

(b)(i) Why thick copper strips: The resistivity of copper is several times less than the resistivity of the experimental alloy wire. As such the area of thick copper strips is more, so copper strips offer almost zero resistance in the circuit.

(b)(ii) Why balance point near the middle: If any one resistance in the Wheatstone bridge is either very small (or very large) in respect of the other, then the balance point might be very close to terminal A or terminal B. So generally the balance point is taken in the middle of the bridge wire.

Teacher's Note: With total length 100 cm, balance gives S = R(100 − l)/l; the end-corrections spoil low-resistance readings.

Exam Note: Memorise S = R(100 − l)/l and ρ = Sπr2/L.

Question 6. Answer the following questions:
(i) State the principle of working a potentiometer. [CBSE Delhi 2010, 2016]
(ii) Draw a circuit diagram to compare the emf of two primary cells. Write the formula used. How can the sensitivity of a potentiometer be increased?
(iii) Write two possible causes for one sided deflection in the potentiometer experiment. [CBSE Delhi 2013]

Solution.

(i) Principle of potentiometer: When a constant current flows through a wire of uniform area of cross-section, the potential drop across any length of the wire is directly proportional to the length.

Circuit diagram. It consists of a long resistance wire AB of uniform cross-section. Its one end A is connected to the positive terminal of battery B1 whose negative terminal is connected to the other end B of the wire through key K and a rheostat (Rh). The battery B1 connected in the circuit is called the driver battery and this circuit is called the primary circuit. By the help of this circuit a definite potential difference is applied across the wire AB; the potential falls continuously along the wire from A to B. The fall of potential per unit length of wire is called the potential gradient. It is denoted by ‘k’. A cell is connected such that its positive terminal is connected to end A and the negative terminal to a jockey J through the galvanometer G. This circuit is called the secondary circuit.

AB+−B1KRhεGJPl

In the primary circuit the rheostat (Rh) is so adjusted that the deflection in the galvanometer is on one side when the jockey is touched on the wire at point A and on the other side when the jockey is touched on the wire at point B.

The jockey is moved and touched to the potentiometer wire and the position is found where the galvanometer gives no deflection. Such a point P is called the null deflection point.

VAB is the potential difference between points A and B and L metre be the length of the wire, then the potential gradient k = VAB/L.

If the length of wire AP in the null deflection position be l, then the potential difference between points A and P, VAP = kl.

∴ The emf of the cell, ε = VAP = kl. In this way the emf of a cell may be determined by a potentiometer.

(ii) Comparison of emfs of two cells: The two cells ε1 and ε2 are connected in turn through a two-way key with their positive terminals to end A, as in the figure. With the same potential gradient k, let the null points be at lengths l1 and l2 from A. Then ε1 = kl1 and ε2 = kl2, so the formula used is ε1/ε2 = l1/l2.

AB+−B1KRhε11ε22two-way keyGJ

Sensitivity of a potentiometer is increased by reducing the potential gradient k = VAB/L, i.e., by increasing the length of the potentiometer wire or by decreasing the current in the primary circuit with the rheostat. A smaller k gives a longer balancing length for the same emf, so the reading is more accurate.

(iii) Two possible causes for one-sided deflection: (a) The emf of the driver battery is less than the emf of the cell being balanced, so no null point exists on the wire. (b) The positive terminals of the driver battery and of the cell are not connected to the same end (A) of the wire.

Teacher's Note: Same current gives potential drop proportional to length, so ε ∝ l for a fixed gradient.

Exam Note: ε1/ε2 = l1/l2; sensitivity rises as gradient falls.

Question 7. Draw the circuit diagram of a potentiometer which can be used to determine the internal resistance of a given cell of emf ε. Describe a method to find the internal resistance of a primary cell. [CBSE (AI) 2013; (F) 2011, 2016]

Solution.

Determination of internal resistance by potentiometer.

Circuit: A battery B1, a rheostat (Rh) and a key K are connected across the ends A and B of the potentiometer wire such that the positive terminal of the battery is connected to point A. This completes the primary circuit.

Now the given cell ε is connected such that its positive terminal is connected to A and its negative terminal to the jockey J through a galvanometer. A resistance box (R) and a key K1 are connected across the cell. This completes the secondary circuit.

AB+−B1KRhεRK1GJ

Method: Initially key K is closed and a potential difference is applied across the wire AB. Now the rheostat Rh is so adjusted that on touching the jockey J at the ends A and B of the potentiometer wire, the deflection in the galvanometer is on both sides. Suppose that in this position the potential gradient on the wire is k.

Now key K1 is kept open and the position of null deflection is obtained by sliding and pressing the jockey on the wire. Let this position be P1 and AP1 = l1.

In this situation the cell is in open circuit, therefore the terminal potential difference will be equal to the emf of the cell, i.e., emf ε = kl1   ...(i)

Now a suitable resistance R is taken in the resistance box and key K1 is closed. Again, the position of the null point is obtained on the wire by using the jockey J. Let this position on the wire be P2 and AP2 = l2.

In this situation the cell is in closed circuit, therefore the terminal potential difference (V) of the cell will be equal to the potential difference across the external resistance R, i.e., V = kl2   ...(ii)

Dividing (i) by (ii), we get ε/V = l1/l2.

∴ Internal resistance of the cell, r = (ε/V − 1)R = (l1/l2 − 1)R. From this formula r may be calculated.

Teacher's Note: Open key gives ε = kl1; closed key gives V = IR = kl2, and r follows from V = ε − Ir.

Exam Note: r = R(l1 − l2)/l2; key K1 open then closed.

Question 8. Answer the following questions:
(i) A cell of emf E and internal resistance r is connected to two external resistances R1 and R2 and a perfect ammeter. The current in the circuit is measured in four different situations: (a) Without any external resistance in the circuit. (b) With resistance R1 only. (c) With R1 and R2 in series combination. (d) With R1 and R2 in parallel combination. The currents measured in the four cases are 0.42 A, 1.05 A, 1.4 A and 4.2 A, but not necessarily in that order. Identify the currents corresponding to the four cases mentioned above.
(ii) A variable resistor R is connected across a cell of emf E and internal resistance ‘r’ as shown in the figure. Plot a graph showing the variation of (a) terminal voltage V and (b) the current I, as a function of R. [CBSE Delhi 2012] [HOTS]

Solution.

(i) The current is largest when the external resistance is zero and smallest for the largest total resistance. The total resistance in the four cases is r (no external resistance), r + R1, r + R1R2/(R1 + R2) (parallel) and r + R1 + R2 (series). The parallel combination has less resistance than R1 alone, which has less than the series combination. Hence the currents rank as

(a) no external resistance: 4.2 A  >  (d) parallel: 1.4 A  >  (b) R1 only: 1.05 A  >  (c) series: 0.42 A.

Check: E/r = 4.2 A. With R1 only, E/(R1 + r) = 1.05 gives R1 + r = 4r, so R1 = 3r. In parallel, E/(Rp + r) = 1.4 gives Rp + r = 3r, so Rp = 2r, i.e., 3rR2/(3r + R2) = 2r, so R2 = 6r. In series, total resistance = r + 3r + 6r = 10r, so I = 4.2r/10r = 0.42 A, which matches.

(ii) The cell with the variable resistor is shown below.

RE, r

Terminal voltage V = E − Ir = E − [E/(R + r)]r

(a) V = RE/(R + r). V is zero at R = 0 and rises with R, approaching E as R becomes very large.

RVE

(b) I = E/(R + r). I is E/r at R = 0 and falls with increasing R, approaching zero (r = internal resistance).

RIE/r

Teacher's Note: Short-circuit current E/r is the largest; V = ER/(R + r) climbs to E while I = E/(R + r) falls.

Exam Note: Largest current is E/r; V → E as R → ∞.

Question 9. Answer the following questions:
(1) (i) State the principle on which a potentiometer works. How can a given potentiometer be made more sensitive?
(ii) In the graph shown below for two potentiometers, state with reason which of the two potentiometers, A or B, is more sensitive.
(2) Two metallic wires, P1 and P2 of the same material and same length but different cross-sectional areas, A1 and A2 are joined together and connected to a source of emf. Find the ratio of the drift velocities of free electrons in the two wires when they are connected (i) in series, and (ii) in parallel. [CBSE (A) 2017]

Solution.

(1)(i) Principle: When a constant current flows through a wire of uniform area of cross-section, the potential drop across any length of the wire is directly proportional to the length.

To make it more sensitive, the value of potential gradient k is kept least possible. Smaller the value of k, greater is the length (l) for the null deflection, and so greater will be the accuracy of measurement.

(ii) Potential gradient = V/l, which is the slope of the V–l graph.

lVAB

∴ The potential gradient of wire A is more than that of wire B. So, wire B is more sensitive than A.

(2) The drift velocity is vd = I/(neA), and the wires have the same n (same material).

(i) In series: the same current I flows through both wires, so v1/v2 = (I/neA1)/(I/neA2) = A2/A1.

(ii) In parallel: the same potential difference V acts across the same length l, so the electric field E = V/l is the same in both wires. Since vd = eτE/m depends only on the material and E, v1/v2 = 1 : 1.

Teacher's Note: Gradient is the slope V/l; the smaller slope (wire B) gives a longer null length.

Exam Note: Less steep V–l line means more sensitive potentiometer.

Question 10. Explain with the help of a circuit diagram how the value of unknown resistance can be determined using a Wheatstone Bridge. Give the formula used.

Solution.

Determination of unknown resistance by Wheatstone bridge. The circuit diagram is completed as shown in the figure. P and Q are each 10 Ω resistance, RB is a resistance box and X is the unknown resistance to be measured. B is a battery with key K1 (in series), G is a galvanometer with key K2 (in series).

P (10 Ω)Q (10 Ω)RBXK2GBACDK1E

The battery key K1 is pressed first and the smallest resistance in RB is introduced; by pressing the galvanometer key K2, the deflection in the galvanometer is noted. Now more resistance in RB is introduced; by pressing the galvanometer key the deflection should be on the other side. This is the main precaution before starting the experiment.

Now a suitable value of resistance in RB is chosen so that on pressing the galvanometer key, there is no deflection in the galvanometer. This resistance R is noted. Now the formula used is P/Q = R/X

⇒ Unknown resistance X = (Q/P)R can be calculated. (Here P = Q = 10 Ω, so X = R.)

Teacher's Note: With P = Q = 10 Ω, balance gives X equal to the resistance box value R.

Exam Note: Balance: P/Q = R/X, so X = (Q/P)R.

Question 11. Figure shows a potentiometer with a cell of 2.0 V and internal resistance of 0.40 Ω maintaining a potential drop across the resistor wire AB. A standard cell which maintains a constant emf of 1.02 V (for very moderate currents up to a few mA) gives a balance point at 67.3 cm length of the wire. To ensure very low currents drawn from the standard cell, a very high resistance of 600 kΩ is put in series with it, which is shorted close to the balance point. The standard cell is then replaced by a cell of unknown emf ε and the balance point found similarly, turns out to be at 82.3 cm length of the wire.
(a) What is the value of ε?
(b) What purpose does the high resistance of 600 kΩ have?
(c) Is the balance point affected by this high resistance?
(d) Is the balance point affected by the internal resistance of the driver cell?
(e) Would the method work in the above situation if the driver cell of the potentiometer had an emf of 1.0 V instead of 2.0 V?
(f) Would the circuit work well for determining extremely small emf, say of the order of a few mV (such as the typical emf of a thermocouple)? If not, how would you modify the circuit?

Solution.

The circuit is shown in the figure (the 600 kΩ resistor is shorted by a key close to the balance point).

AB2 V0.40 Ωε600 kΩGJ

(a) For the same potential gradient of the potentiometer wire, the formula for comparison of emfs of cells is εs/ε = ls/l, i.e., ε = (l/ls)εs, where

εs = emf of standard cell = 1.02 V, ls = balancing length with the standard cell = 67.3 cm, l = balancing length with the cell of unknown emf = 82.3 cm.

∴ Unknown emf ε = (82.3 cm/67.3 cm) × 1.02 V = 1.25 V.

(b) The purpose of the high resistance is to reduce the current through the galvanometer. When the jockey is far from the balance point, this saves the standard cell from being damaged.

(c) The balance point is not affected by the presence of the high resistance because in the balanced position there is no current in the cell-circuit (secondary circuit).

(d) No, the balance point is not affected by the internal resistance of the driver cell, because we have already set the constant potential gradient of the wire.

(e) No, since for the working of a potentiometer the emf of the driver cell must be greater than the emf of the secondary circuit.

(f) No, the circuit will have to be modified by putting a variable resistance (R) in series with the driver cell. The value of R is so adjusted that the potential drop across the wire is slightly greater than the emf of the secondary cell, so that the balance point may be obtained at a longer length. This will reduce the error and increase the accuracy of measurement.

Teacher's Note: Same gradient lets emfs be compared directly by balancing lengths: ε = 1.02 × 82.3/67.3.

Exam Note: Answer ε = 1.25 V; driver emf must exceed ε.

Question 12. Figure shows a potentiometer circuit for comparison of two resistances. The balance point with a standard resistance R = 10.0 Ω is found to be 58.3 cm, while that with the unknown resistance X is 68.5 cm. Determine the value of X. What might you do if you failed to find a balance point with the given cell ε?

Solution.

The cell ε sends the same current I through R and X, which are in series with it. The potentiometer is connected first across R and then across X, as in the figure.

AB+−B1KRhεRXGJ

In the first case, the p.d. across R is V1 = IR   ...(i)

In the second case, the p.d. across X is V2 = IX   ...(ii)

Let k be the potential gradient of the potentiometer wire. If l1 and l2 are the balancing lengths corresponding to R and X respectively, then V1 = kl1   ...(iii) and V2 = kl2   ...(iv)

From (i) and (iii): IR = kl1   ...(v). From (ii) and (iv): IX = kl2   ...(vi)

Dividing (vi) by (v), we get X/R = l2/l1  ⇒  X = (l2/l1)R.

Here, R = 10.0 Ω, l1 = 58.3 cm, l2 = 68.5 cm.

∴ X = (68.5/58.3) × 10.0 = 11.75 Ω.

If we fail to find the balance point with the given cell ε, then we shall take the driver battery (B1) of higher emf than the given emf (ε).

Teacher's Note: Same series current I makes the potentials across R and X proportional to their balancing lengths.

Exam Note: X = R l2/l1 = 11.75 Ω.

Question 13. You are given two sets of potentiometer circuits to measure the emf E1 of a cell.
Set A: consists of a potentiometer wire of a material of resistivity ρ1, area of cross-section A1 and length l.
Set B: consists of a potentiometer of two composite wires of equal lengths l/2 each, of resistivity ρ1, ρ2 and area of cross-section A1, A2 respectively.
Find the relation between resistivity of the two wires with respect to their area of cross-section, if the current flowing in the two sets is the same. Compare the balancing length obtained in the two sets. [CBSE Sample Paper 2016]

Solution.

(i) Let R be the series resistance (with the driver cell of emf E) in each set. Resistance of wire A = ρ1l/A1; resistance of wire B = ρ1(l/2)/A1 + ρ2(l/2)/A2.

I = E/(R + ρ1l/A1) for set A and I = E/(R + ρ1l/2A1 + ρ2l/2A2) for set B.

Equating the two currents, R + ρ1l/A1 = R + ρ1l/2A1 + ρ2l/2A2   ...(i)

⇒ ρ1l/A1 − ρ1l/2A1 = ρ2l/2A2  ⇒  ρ1/A1 = ρ2/A2.

Set Aρ1, A1, length lERSet Bρ1A1l/2ρ2A2l/2ER

(ii) Potential gradient of the potentiometer wire for set A, k = Iρ1/A1.

Potential drop across the potentiometer wire in set B, V = I(ρ1l/2A1 + ρ2l/2A2) = (l/2)(ρ1/A1 + ρ2/A2)I.

Potential gradient in set B, k′ = V/l = (I/2)(ρ1/A1 + ρ2/A2). Using the condition (i), we get k′ = Iρ1/A1, which is equal to k.

Therefore, the balancing length obtained in the two sets is the same.

Teacher's Note: Equal currents and equal wire resistance give equal potential gradients, hence the same balance length for E1.

Exam Note: Same gradient in both sets gives the same balancing length.

Class 12 Mathematics: Xam Idea Solutions for Xam Idea Solutions Class 12 Physics Chapter 3 Current Electricity Long Answer Questions

Access Class 12 Mathematics Solutions

Review detailed solutions for Class 12 Mathematics. The Xam Idea Solutions Class 12 Physics Chapter 3 Current Electricity Long Answer Questions PDF provides comprehensive answers mapped to standard Xam Idea Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.

Concept-Driven Math Answers

Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.

Next Steps in Your Mathematics Revision

Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.

FAQs

What are these [current-page:node:field_author] Solutions for Class 12 Physics?

They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.

Are the [current-page:node:field_author] Class 12 Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these [current-page:node:field_author] solutions for Class 12 Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising [current-page:node:field_author] Class 12 Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these Class 12 Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.