Xam Idea Solutions Class 12 Physics Chapter 2 Electrostatic Potential And Capacitance Short Answer Questions I

Solutions for Class 12 Physics: Chapter 02 Electrostatic Potential And Capacitance

Explore reliable textbook solutions for Chapter 02 Electrostatic Potential And Capacitance tailored for Class 12 learners using methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.

Practice Class 12 Physics Solutions: Chapter 02 Electrostatic Potential And Capacitance

View or download the dedicated Chapter 02 Electrostatic Potential And Capacitance solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Physics.

Short Answer Questions I

Question 1. What is electrostatic shielding? How is this property used in actual practice? Is the potential in the cavity of a charged conductor zero? [CBSE South 2016]

Solution.

Whatever be the charge and field configuration outside, any cavity in a conductor remains shielded from outside electric influence. The field inside a conductor is zero. This is known as electrostatic shielding.

Sensitive instruments are shielded from outside electrical influences by enclosing them in a hollow conductor.

During lightning it is safest to sit inside a car, rather than near a tree. The metallic body of a car becomes an electrostatic shielding from lightening.

Potential inside the cavity is not zero. Potential is constant.

Teacher's Note: A conductor's interior field is zero, so a cavity inside stays shielded from outside electric influence.

Exam Note: Define shielding, give one use, mention constant cavity potential.

Question 2. Three points A, B and C lie in a uniform electric field (E) of 5 × 103 NC−1 as shown in the figure. Find the potential difference between A and C. [CBSE (F) 2009]

Solution.

ABC5 cm3 cmE

The line joining B to C is perpendicular to electric field, so potential of B = potential of C i.e., VB = VC.

Distance AB = √(52 − 32) = 4 cm.

Potential difference between A and C = E × (AB) = 5 × 103 × (4 × 10−2) = 200 volt.

Teacher's Note: Potential difference depends on the distance measured along the field direction.

Exam Note: Use AB = 4 cm along E.

Question 3. Two uniformly large parallel thin plates having charge densities +σ and −σ are kept in the X-Z plane at a distance ‘d’ apart. Sketch an equipotential surface due to electric field between the plates. If a particle of mass m and charge ‘−q’ remains stationary between the plates, what is the magnitude and direction of this field? [CBSE Delhi 2011]

Solution.

The equipotential surface is at a distance d/2 from either plate in X-Z plane. For a particle of charge (−q) at rest between the plates:

+σ−σV = 0Equipotentialsurfacedy

(i) Weight mg acts vertically downward. (ii) Electric force qE acts vertically upward. So mg = qE, giving E = mg/q, vertically downward, i.e., along the −Y axis.

Teacher's Note: The midplane between oppositely charged plates is the equipotential surface.

Exam Note: Balance mg with qE; field points down.

Question 4. Plot a graph comparing the variation of potential ‘V’ and electric field ‘E’ due to a point charge ‘Q’ as a function of distance ‘R’ from the point charge. [CBSE Delhi 2012]

Solution.

The graph of variation of potential and electric field due to a point charge Q with distance R from the point charge is shown in figure.

RE or VE ∝ 1/r²V ∝ 1/r

Teacher's Note: Potential falls as 1/r while field falls faster, as 1/r².

Exam Note: Draw both decreasing curves; label proportions.

Question 5. Draw 3 equipotential surfaces corresponding to a field that uniformly increases in magnitude but remains constant along Z-direction. How are these surfaces different from that of a constant electric field along Z-direction? [CBSE (AI) 2009]

Solution.

V2V3Vd1 = d2V2V3Vd1 > d2

Difference: For constant electric field, the equipotential surfaces are equidistant for same potential difference between these surfaces; while for increasing electric field, the separation between these surfaces decreases, in the direction of increasing field, for the same potential difference between them.

Teacher's Note: Surfaces crowd together where the field is stronger.

Exam Note: Show equal spacing versus decreasing spacing.

Question 6. Why does current in a steady state not flow in a capacitor connected across a battery? However momentary current does flow during charging or discharging of the capacitor. Explain. [CBSE (AI) 2017]

Solution.

(i) In the steady state no current flows through capacitor because, we have two sources (battery and fully charged capacitor) of equal potential connected in opposition.

(ii) During charging or discharging there is a momentary flow of current as the potentials of the two sources are not equal to each other.

Teacher's Note: A fully charged capacitor opposes the battery equally, so no net current flows.

Exam Note: Mention opposing equal potentials; momentary current.

Question 7. A test charge ‘q’ is moved without acceleration from A to C along the path from A to B and then from B to C in electric field E as shown in the figure. (i) Calculate the potential difference between A and C. (ii) At which point (of the two) is the electric potential more and why? [CBSE (AI) 2012]

Solution.

B (2, 3)C (2, 0)A (6, 0)E

(i) Since electric field is conservative in nature, the amount of work done depends only on initial and final positions. Displacement AC = 4 units against the field direction. Work done by the field W = qE · AC cos 180° = −4qE. Hence VC − VA = −W/q = 4E (potential difference of magnitude 4E, with distances in metres and E in V/m).

(ii) VC > VA, because the direction of electric field is in the direction of decreasing potential.

Teacher's Note: Moving against the field raises potential, and path does not matter.

Exam Note: Use displacement along E; C is higher.

Question 8. Figure shows a sheet of aluminium foil of negligible thickness placed between the plates of a capacitor. How will its capacitance be affected if: (i) The foil is electrically insulated? (ii) The foil is connected to the upper plate with a conducting wire? [CBSE (F) 2009]

Solution.

Foil

(i) No effect on capacitance if foil is electrically neutral.

(ii) If foil is connected to upper plate with a conducting wire, the effective separation between plates becomes half, so capacitance is doubled.

Teacher's Note: A neutral thin foil leaves C unchanged; connecting it to a plate halves the gap.

Exam Note: Answer: no change; doubled.

Question 9. Find the charge on the capacitor as shown in the circuit. [CBSE (F) 2014]

Solution.

6 µF10 Ω20 Ω2 V

Total resistance R = 10 Ω + 20 Ω = 30 Ω.

The current I = V/R = 2 V/30 Ω = 1/15 A.

The capacitor is connected across the 10 Ω resistor, so potential difference V = IR = (1/15) × 10 = 2/3 V.

Charge q = CV = 6 × (2/3) = 4 µC.

Teacher's Note: In steady state the capacitor carries no current; its voltage equals that across the 10 Ω resistor.

Exam Note: Find current, then voltage across capacitor.

Question 10. Figure shows two identical capacitors, C1 and C2, each of 1 µF capacitance connected to a battery of 6 V. Initially switch ‘S’ is closed. After sometime ‘S’ is left open and dielectric slabs of dielectric constant K = 3 are inserted to fill completely the space between the plates of the two capacitors. How will the (i) charge and (ii) potential difference between the plates of the capacitors be affected after the slabs are inserted? [CBSE Delhi 2011]

Solution.

6 V1 µF C11 µF C2S

When switch S is closed, p.d. across each capacitor is 6 V, V1 = V2 = 6 V and C1 = C2 = 1 µF.

∴ Charge on each capacitor q1 = q2 (= CV) = (1 µF) × (6 V) = 6 µC.

When switch S is opened, the p.d. across C1 remains 6 V (it stays connected to the battery), while the charge on capacitor C2 remains 6 µC. After insertion of dielectric between the plates of each capacitor, the new capacitance of each capacitor becomes C′1 = C′2 = 3 × 1 µF = 3 µF.

Charge on capacitor C1, q′1 = C′1V1 = (3 µF) × 6 V = 18 µC. Charge on capacitor C2 remains 6 µC.

Potential difference across C1 remains 6 V. Potential difference across C2 becomes V′2 = q2/C′2 = 6 µC/3 µF = 2 V.

Teacher's Note: The capacitor on the battery keeps its voltage; the isolated one keeps its charge.

Exam Note: Treat C1 at constant V and C2 at constant Q.

Question 11. (i) A parallel plate capacitor (C1) having charge Q is connected, to an identical uncharged capacitor C2 in series. What would be the charge accumulated on the capacitor C2? (ii) Three identical capacitors each of capacitance 3 µF are connected, in turn, in series and in parallel combination to the common source of V volt. Find out the ratio of the energies stored in two configurations. [CBSE South 2016]

Solution.

(i) Zero.

(ii) We have Cseries = 3 µF/3 = 1 µF. Also, Cparallel = (3 + 3 + 3) = 9 µF.

Energy stored = ½CV2. Energy in series combination Useries = ½ × 1 × 10−6 × V2. Energy in parallel combination Uparallel = ½ × 9 × 10−6 × V2.

∴ Useries : Uparallel = 1 : 9

Teacher's Note: At the same voltage, stored energy is proportional to capacitance.

Exam Note: Find both capacitances; take the ratio.

Question 12. Net capacitance of three identical capacitors in series is 1 µF. What will be their net capacitance if connected in parallel? Find the ratio of energy stored in the two configurations if they are both connected to the same source. [CBSE (AI) 2011]

Solution.

Let C be the capacitance of each capacitor, then in series 1/Cs = 1/C + 1/C + 1/C = 3/C. Or C = 3Cs = 3 × 1 µF = 3 µF.

When these capacitors are connected in parallel, net capacitance, Cp = 3C = 3 × 3 = 9 µF.

When these two combinations are connected to same source the potential difference across each combination is same. Ratio of energy stored Us/Up = (½CsV2)/(½CpV2) = Cs/Cp = 1 µF/9 µF = 1/9.

Us : Up = 1 : 9

Teacher's Note: Same voltage means energy is proportional to capacitance.

Exam Note: Find C = 3 µF, then Cp = 9 µF.

Question 13. Find the equivalent capacitance of the network shown in the figure, when each capacitor is of 1 µF. When the ends X and Y are connected to a 6 V battery, find out (i) The charge and (ii) The energy stored in the network. [CBSE Patna 2015]

Solution.

XYABCCCCC (bridge)

It is known as Wheatstone bridge of the capacitor. Since VA = VB, the bridge capacitor between points A and B can be removed.

(i) The equivalent capacitance of the network Ceq = (C × C)/(C + C) + (C × C)/(C + C) = C/2 + C/2 = C = 1 µF. Charge in the network, Q = CeqV = 1 µF × 6 V = 6 µC.

(ii) Energy stored in the capacitor, U = ½CeqV2 = ½ × 1 µF × (6)2 = 18 µJ.

Teacher's Note: A balanced capacitor bridge has no charge on its middle capacitor, so it can be removed.

Exam Note: Remove the bridge capacitor, then combine.

Question 14. A network of four capacitors each of 15 µF capacitance is connected to a 500 V supply as shown in the figure. Determine (a) Equivalent capacitance of the network and (b) Charge on each capacitor. [CBSE (AI) 2010]

Solution.

C1C3C2C4AB← 500 V →

(a) C1, C2 and C3 are in series, so their equivalent capacitance C′ is given by 1/C′ = 1/C1 + 1/C2 + 1/C3 = 1/15 + 1/15 + 1/15, so C′ = 5 µF. C4 is in parallel with C′, so equivalent capacitance of network Ceq = C′ + C4 = 5 + 15 = 20 µF.

(b) Charge on capacitor C4 is q4 = C4V = (15 µF) × 500 V = 7500 µC = 7.5 mC. Charge on C1, C2 and C3 is q1 = q2 = q3 = C′V = 5 µF × 500 V = 2500 µC = 2.5 mC.

Teacher's Note: Series capacitors share the same charge; the parallel branch gets the full supply voltage.

Exam Note: Reduce the series group, then add in parallel.

Question 15. Four charges +q, −q, +q and −q are to be arranged respectively at the four corners of a square ABCD of side ‘a’. (i) Find the work required to put together this arrangement. (ii) A charge q0 is brought to the centre of the square, the four charges being held fixed. How much extra work is needed to do this? [HOTS][CBSE (F) 2015]

Solution.

+−+−ABCD

(i) Work done in bringing charge +q at point A: WA = 0.

Work done in bringing charge −q to the point B: WB = −q × (1/4πε0)(q/a) = −(1/4πε0)(q2/a).

Work done in bringing charge +q to the point C: WC = WAC + WBC = q × (1/4πε0)(q/a√2) + q × (−1/4πε0)(q/a) = (1/4πε0)(q2/a)(1/√2 − 1).

Work done in bringing charge −q to the point D: WD = WAD + WBD + WCD = (1/4πε0)(q2/a)(−1 + 1/√2 − 1).

Total work done W = WA + WB + WC + WD = 2 × (1/4πε0)(q2/a√2) − 4 × (1/4πε0)(q2/a) = (1/4πε0)(q2/a)(√2 − 4).

(ii) The centre of the square is equidistant from the four charges, two positive and two negative, so the potential at the centre is zero. Hence the extra work needed to bring q0 to the centre is W = q0 × 0 = 0.

Teacher's Note: Total work is the potential energy of the arrangement; the centre is at zero potential.

Exam Note: Add pair energies; show centre potential is zero.

Question 16. Establish the relation between electric field and potential gradient.

Solution.

Let us consider two closely spaced equipotential surfaces A and B as shown in figure.

V − dVVBAdrEEquipotentials

Let the potential of A be VA = V and potential of B be VB = V − dV, where dV is decrease in potential in the direction of electric field E normal to A and B.

Let dr be the perpendicular distance between the two equipotential surfaces. When a unit positive charge is moved along this perpendicular from the surface B to surface A against the electric field, the work done in this process is WBA = −E (dr).

This work done equals the potential difference VA − VB. ∴ WBA = VA − VB = V − (V − dV) = dV, so −E dr = dV or E = −dV/dr = negative of potential gradient.

Teacher's Note: Field equals the negative rate of change of potential with distance.

Exam Note: Derive E = −dV/dr.

Question 17. How does the energy stored in a capacitor change if after disconnecting the battery, the plates of a charged capacitor are moved farther apart?

Solution.

Capacitance C ∝ 1/d, so when plates of a capacitor are moved farther, the capacitance decreases. After disconnecting the battery, the charge on capacitor remains constant, therefore the energy stored by capacitor U = q2/2C increases.

Teacher's Note: Charge stays fixed after disconnection, so smaller C means larger U = q²/2C.

Exam Note: State C decreases, Q constant, U increases.

Question 18. How does the energy stored in a capacitor change if the plates of a charged capacitor are moved farther apart, the battery remaining connected?

Solution.

The capacitance of capacitor decreases on moving its plates farther. As the battery remains connected, the potential difference remains constant. Hence, energy stored U = ½CV2 decreases.

Teacher's Note: With the battery connected V is fixed, so smaller C means smaller U = ½CV².

Exam Note: State C decreases, V constant, U decreases.

Question 19. When a capacitor is charged by a battery; is the energy stored in the capacitor same as energy supplied by the battery?

Solution.

No. Energy stored in the capacitor = ½CV2 = ½qV while energy supplied by battery = qV.

The balance of energy is dissipated as heat during charging.

Teacher's Note: Half of the battery’s energy is lost as heat while charging.

Exam Note: Say no; stored is half of supplied.

Question 20. The given graph shows the variation of charge q versus potential difference V for two capacitors C1 and C2. The two capacitors have same plate separation but the plate area of C2 is double than that of C1. Which of the two graphs P and Q correspond to capacitors C1 and C2 and why?

Solution.

VqQP

Q represents C2 and P represents C1.

Reason: From the graph, slope q/V = capacitance is greater for Q. Also according to given conditions the capacitance C = εA/d is larger for the C2 because the area of its plates is large and d for the two capacitors is same. Hence, Q represents C2.

Teacher's Note: The graph’s slope gives capacitance, and double plate area doubles capacitance.

Exam Note: Match steeper graph with larger capacitance.

Question 21. Find the total energy stored in the capacitors in the given network.

Solution.

C1 = 2 µFC2 = 2 µF6 VC4 = 1 µFC3 = 1 µFC5 = 2 µFAB

The equivalent capacitance of C1 and C2 in series is C′ = (2 × 2)/(2 + 2) = 1 µF.

C′ is in parallel with C3, so equivalent capacitance of C1, C2 and C3 is C″ = 1 + 1 = 2 µF.

C″ is in series with C5; their equivalent capacitance C‴ = (2 × 2)/(2 + 2) = 1 µF.

This is in parallel with C4, so equivalent capacitance across AB is CAB = 1 + 1 = 2 µF.

Energy stored = ½CABV2 = ½ × 2 × 10−6 × (6)2 = 36 × 10−6 J.

Teacher's Note: Combine series and parallel groups step by step, then use U = ½CV².

Exam Note: Find CAB = 2 µF, then energy 36 µJ.

Question 22. Three point charges +Q, −2Q and −3Q are placed at the vertices of an equilateral triangle ABC of side l. If these charges are displaced to the mid points A1, B1 and C1 respectively, calculate the amount of work done in shifting the charges to the new locations. [HOTS]

Solution.

A (+Q)B (−2Q)C (−3Q)A1C1B1

Work done to put the three charges at A, B and C: Uinitial = (1/4πε0)[Q(−2Q)/l + (−2Q)(−3Q)/l + (−3Q)(Q)/l] = (1/4πε0)(Q2/l)(−2 + 6 − 3) = (1/4πε0)(Q2/l).

When the charges are at A1, B1 and C1, every separation becomes l/2, so Ufinal = (1/4πε0)(2Q2/l).

Work done to shift the charges to the new locations W = Ufinal − Uinitial = (1/4πε0)(2Q2/l) − (1/4πε0)(Q2/l) = (1/4πε0)(Q2/l).

Teacher's Note: Work done equals the change in electrostatic potential energy of the system.

Exam Note: Compute Uinitial and Ufinal, then subtract.

Question 23. Consider two conducting spheres of radii R1 and R2 with R1 > R2. If the two are at the same potential, the larger sphere has more charge than the smaller sphere. State whether the charge density of the smaller sphere is more or less than that of the larger one. [HOTS][NCERT Exemplar]

Solution.

Since two spheres are at the same potential, V1 = V2, so Q1/(4πε0R1) = Q2/(4πε0R2), that is Q1/Q2 = R1/R2 ... (i)

Given R1 > R2, therefore Q1 > Q2. So the larger sphere has more charge.

Now, σ1 = Q1/4πR12 and σ2 = Q2/4πR22, so σ2/σ1 = (Q2/Q1)(R12/R22) = (R2/R1)(R12/R22) = R1/R2 [from equation (i)].

Since R1 > R2, therefore σ2 > σ1. Charge density of smaller sphere is more than that of larger one.

Teacher's Note: At equal potential, charge is proportional to radius, so density is inversely proportional to radius.

Exam Note: Equal potential gives Q ∝ R; then compare densities.

Question 24. The two graphs are drawn below, show the variations of electrostatic potential (V) 1/r (r being the distance of field point from the point charge) for two point charges q1 and q2. (i) What are the signs of the two charges? (ii) Which of the two charges has the larger magnitude and why? [HOTS]

Solution.

q1q2(1/r)V

(i) The potential due to positive charge is positive and due to negative charge, it is negative, so, is q1 positive and q2 is negative.

(ii) V = (1/4πε0)(q/r). The graph between V and 1/r is a straight line passing through the origin with slope q/4πε0. As the magnitude of slope of the line due to charge q2 is greater than that due to q1, q2 has larger magnitude.

Teacher's Note: On a V against 1/r graph the slope equals q/4πε0.

Exam Note: Read the sign from slope; compare slopes.

Question 25. The potential V due to a charge distribution at a point (x, y) is given by V = −x2 + 3y. Calculate the electric field, in magnitude and direction, due to this charge configuration at the point (1, 1). [HOTS]

Solution.

V = −x2 + 3y

∴ Ex = −∂V/∂x = +2x and Ey = −∂V/∂y = −3.

Total E = 2x i − 3 j. At point (1, 1), E = 2 i − 3 j.

|E| = √(22 + 32) = √13 N/C ≈ 3.6 N/C.

The angle θ with the x-axis: tan θ = Ey/Ex = −3/2 = −1.5, so θ = tan−1(−1.5) ≈ −56°, that is 56° below the +x axis.

Teacher's Note: The field is the negative gradient of potential in each coordinate direction.

Exam Note: Differentiate V with x and y.

Question 26. Two charges 5 nC and −2 nC are placed at points (5 cm, 0, 0) and (23 cm, 0, 0) in a region of space where there is no other external field. Calculate the electrostatic potential energy of this charge system. [HOTS]

Solution.

Given q1 = 5 nC = 5 × 10−9 C, q2 = −2 nC = −2 × 10−9 C.

The charges are placed on X-axis. The distance between the charges r = x2 − x1 = (23 − 5) cm = 18 cm = 0.18 m.

∴ Electrostatic potential energy of charges U = (1/4πε0)(q1q2/r) = [9 × 109 × (5 × 10−9)(−2 × 10−9)]/0.18 = −5 × 10−7 J.

Teacher's Note: Unlike charges attract, so their potential energy is negative.

Exam Note: Use U = kq1q2/r with signs.

Question 27. A very thin plate of metal is placed exactly in the middle of the two plates of a parallel plate capacitor. What will be the effect on the capacitance of the system? [HOTS]

Solution.

For a metal K = ∞ and so when t << d, the capacitance C = ε0A/[d − t(1 − 1/K)] = ε0A/(d − t).

As t << d, C = ε0A/d, i.e., capacitance will remain unchanged.

Teacher's Note: A very thin metal plate hardly changes the effective separation.

Exam Note: Say capacitance unchanged since t is tiny.

Class 12 Mathematics: Xam Idea Solutions for Xam Idea Solutions Class 12 Physics Chapter 2 Electrostatic Potential And Capacitance Short Answer Questions I

Access Class 12 Mathematics Solutions

Access the complete chapter-wise PDF for Xam Idea Solutions Class 12 Physics Chapter 2 Electrostatic Potential And Capacitance Short Answer Questions I. These structured Xam Idea Solutions solutions for Class 12 Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.

Concept-Driven Math Answers

Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.

Additional Study Materials for 2026

Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.

FAQs

What are these [current-page:node:field_author] Solutions for Class 12 Physics?

They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.

Are the [current-page:node:field_author] Class 12 Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these [current-page:node:field_author] solutions for Class 12 Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising [current-page:node:field_author] Class 12 Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these Class 12 Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.