Step-by-Step Solutions for Class 12 Physics Chapter 04 Moving Charges And Magnetism
Review structured textbook solutions for Class 12 Physics Chapter 04 Moving Charges And Magnetism prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Download Chapter 04 Moving Charges And Magnetism Textbook Solutions PDF
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Short Answer Questions II
Question 1. Write any two important points of similarities and differences each between Coulomb’s law for the electrostatic field and Biot-Savart’s law for the magnetic field. [CBSE (F) 2015]
Solution.
Similarities:
Both electrostatic field and magnetic field:
Follows the principle of superposition.
Depends inversely on the square of distance from source to the point of interest.
Differences:
(i) Electrostatic field is produced by a scalar source (q) and the magnetic field is 𝑑𝐼→). produced by a vector (I
(ii) Electrostatic field is along the displacement vector between source and point of interest; while magnetic field is perpendicular to the plane, containing the displacement vector and vector source.
(iii) Electrostatic field is angle independent, while magnetic field is angle dependent between source vector and displacement vector.
Teacher's Note: Both laws follow inverse square and superposition, but differ in source type and field direction.
Exam Note: Give two similarities, two differences.
Question 2. An electron and a proton enter a region of uniform magnetic field B with uniform speed v in a perpendicular direction (fig.). (i) Show the trajectories followed by two particles. (ii) What is the ratio of the radii of the circular paths of electron to proton? [CBSE (F) 2010]
Solution.
(i) Trajectories are shown in the figure. Both particles describe semicircles in the field, in opposite senses; the proton (heavier) describes the larger one.
(ii) As r = mv/qB, for the same v, B and charge magnitude, r ∝ m.
Ratio of radii of electron path and proton path: re/rp = me/mp
As mass of proton mp ≈ 1840 × mass of electron (me)
∴ me/mp ≈ 1/1840 and re/rp = 1/1840.
Teacher's Note: Same charge magnitude and speed, so radius depends only on mass; the lighter electron curves more tightly.
Exam Note: r = mv/qB, so re:rp = 1:1840.
Question 3. Answer the following questions. (i) A point charge q moving with speed v enters a uniform magnetic field B that is acting into the plane of the paper as shown. What is the path followed by the charge q and in which plane does it move? (ii) How does the path followed by the charge get affected if its velocity has a component parallel to B? (iii) If an electric field is also applied such that the particle continues moving along the original straight line path, what should be the magnitude and direction of the electric field? [CBSE (F) 2016]
Solution.
(i) The force experienced by the charge particle is given by F = q (V × B).
When V is perpendicular to B the force on the charge particle acts as the centripetal force and makes it move along a circular path. Path followed by charge is anticlockwise in X-Y plane. The point charge moves in the plane perpendicular to both V and B.
(ii) The component of velocity perpendicular to B still gives circular motion, while the component parallel to B is unaffected. The path becomes a helix whose axis is along B.
(iii) The electric force must balance the magnetic force: qE = qvB, so E = vB. Its direction is perpendicular to both v and B, opposite to the magnetic force. Here the magnetic force on q is along –Y, so E must point along +Y (in the plane of the paper, perpendicular to v).
Teacher's Note: Perpendicular velocity gives a circle; a parallel component adds drift, making a helix; undeflected motion needs qE = qvB.
Exam Note: Circle; helix if v has component along B; E = vB.
Question 4. How is a galvanometer converted into a voltmeter and an ammeter? Draw the relevant diagrams and find the resistance of the arrangement in each case. Take resistance of galvanometer as G. [CBSE East 2016]
Solution.
A galvanometer is converted into a voltmeter by connecting a high resistance ‘R’ in series with it.
A galvanometer is converted into an ammeter by connecting a small resistance (called shunt) in parallel with it.
Resistance of voltmeter, RV = G + R
Resistance of ammeter, RA = G rs/(G + rs)
Teacher's Note: Series resistance raises the total resistance (voltmeter); parallel shunt lowers it below G (ammeter).
Exam Note: Voltmeter: R in series. Ammeter: shunt in parallel.
Question 5. Derive an expression for the axial magnetic field of a finite solenoid of length 2l and radius r carrying current I. Under what condition does the field become equivalent to that produced by a bar magnet? [CBSE South 2016]
Solution.
Consider a solenoid of length 2l, radius r and carrying a current I and having n turns per unit length.
Consider a point P at a distance a from the centre O of solenoid. Consider an element of solenoid of length dx at a distance x from its centre. This element is a circular current loop having (n dx) turns. The magnetic field at axial point P due to this current loop is
dB = μ0 (n dx) I r² / 2{r² + (a – x)²}3/2
The total magnetic field due to entire solenoid is
B = ∫ from –l to +l of μ0 (n dx) I r² / 2{r² + (a – x)²}3/2
For a >> l and a >> r, we have {r² + (a – x)²}3/2 = a³
∴ B = (μ0 n I r² / 2a³) ∫ from –l to +l of dx = μ0 n I r² (2l) / 2a³
The magnetic moment of solenoid m (= NIA) = (n 2l) I · πr²
∴ B = (μ0/4π)(2m/a³)
This is also the far axial magnetic field of a bar magnet. Hence, the magnetic field, due to current carrying solenoid along its axial line is similar to that of a bar magnet for far off axial points (a >> l and a >> r).
Teacher's Note: Integrating loop fields along the length gives the dipole form 2m/a³ once the point is far away.
Exam Note: Condition: axial point far away, a >> l and a >> r.
Question 6. A cyclotron’s oscillator frequency is 10 MHz. What should be the operating magnetic field for accelerating protons? If the radius of its ‘dees’ is 60 cm, calculate the kinetic energy (in MeV) of the proton beam produced by the accelerator. [CBSE Ajmer 2015]
Solution.
The oscillator frequency should be same as proton cyclotron frequency, ν = qB/2πm, then
Magnetic field, B = 2π m ν / q = (2 × 3.14 × 1.67 × 10–27 × 107) / (1.6 × 10–19) = 0.66 T
v = rω = r × 2πν = 0.6 × 2 × 3.14 × 107 = 3.77 × 107 m/s
So, kinetic energy, KE = ½ m v² = ½ × 1.67 × 10–27 × (3.77 × 107)² J
= ½ × (1.67 × 10–27 × 14.2 × 1014) / (1.6 × 10–13) MeV = 7.4 MeV
Teacher's Note: Resonance fixes B from the frequency; the exit speed is v = 2πνR, giving the beam energy.
Exam Note: B ≈ 0.66 T; KE ≈ 7.4 MeV.
Question 7. A circular coil of ‘N’ turns and diameter ‘d’ carries a current ‘I’. It is unwound and rewound to make another coil of diameter ‘2d’, current ‘I’ remaining the same. Calculate the ratio of the magnetic moments of the new coil and the original coil. [CBSE (AI) 2012]
Solution.
We know, magnetic moment (m) = NIA, where N = number of turns.
The length of wire remains the same. Thus, N × [2π(d/2)] = N′ × [2π(2d/2)] ⇒ N′ = N/2
Now, mA = N I AA = N I (π d²/4) = ¼ N I π d²
Similarly, mB = N′ I AB = (N/2) I (π d²) = ½ N I π d²
mB/mA = (½)/(¼) = 2, i.e. the ratio of magnetic moments of new coil and original coil is 2 : 1.
Teacher's Note: Doubling the diameter halves the turns but quadruples the area, so the moment doubles.
Exam Note: Wire length fixed: N′ = N/2; ratio = 2.
Question 8. Two small identical circular loops, marked (1) and (2), carrying equal currents, are placed with the geometrical axes perpendicular to each other as shown in the figure. Find the magnitude and direction of the net magnetic field produced at the point O. [CBSE (F) 2013, 2014]
Solution.
Magnetic field due to coil 1 at point O: B1 = μ0 i R² / 2(R² + x²)3/2 along OC1.
Magnetic field due to coil 2 at point O: B2 = μ0 i R² / 2(R² + x²)3/2 along C2O.
B1 and B2 are mutually perpendicular, so the net magnetic field at O is
B = √(B1² + B2²) = √2 B1 (as B1 = B2) = √2 μ0 i R² / 2(R² + x²)3/2
As R << x: B = √2 μ0 i R² / 2x³ = (μ0/4π)(2√2 i A / x³), where A = πR² is area of loop.
tan θ = B2/B1 = 1 (∵ B2 = B1) ⇒ θ = π/4
∴ B is directed at an angle π/4 with the direction of magnetic field B1.
Teacher's Note: Axial fields of the two perpendicular loops are equal and at right angles, so add as a square diagonal.
Exam Note: B = √2 B1, at 45° to B1.
Question 9. Two identical coils P and Q each of radius R are lying in perpendicular planes such that they have a common centre. Find the magnitude and direction of magnetic field at the common centre of the two coils, if they carry currents equal to I and –√3 I respectively. [CBSE (F) 2016] [HOTS]
Solution.
Given that two identical coils are lying in perpendicular planes and having common centre. P and Q carry current I and √3 I respectively (the negative sign only fixes the sense of the current in Q; it does not change the magnitude).
Magnetic field at the centre of P due to its current I: BP = μ0 I / 2R. Magnetic field at the centre of Q due to its current √3 I: BQ = μ0 √3 I / 2R.
∴ |Bnet| = √(BP² + BQ²) = √[(μ0I/2R)² + (μ0√3I/2R)²] = (μ0I/2R) × 2 = μ0 I / R
tan θ = |BP|/|BQ| = 1/√3 ⇒ θ = tan–1(1/√3) = 30°
So the net field is μ0I/R, making an angle of 30° with the field BQ (i.e. with the axis of coil Q).
Teacher's Note: Perpendicular coil axes make the fields perpendicular; magnitudes 1 : √3 give a 30°–60° resultant.
Exam Note: B = μ0I/R at 30° to BQ.
Question 10. Two identical circular loops, P and Q, each of radius r and carrying currents I and 2I respectively are lying in parallel planes such that they have a common axis. The direction of current in both the loops is clockwise as seen from O which is equidistant from the both loops. Find the magnitude of the net magnetic field at point O. [CBSE (AI) 2012] [HOTS]
Solution.
Distance of O from each loop is r. Both loops are clockwise as seen from O, so the field of P at O points towards P and the field of Q at O points towards Q, i.e. they are opposite.
|BP| = μ0 I r² / 2(r² + r²)3/2 = μ0 I / 4√2 r (pointing towards P)
|BQ| = μ0 (2I) r² / 2(r² + r²)3/2 = μ0 2I / 4√2 r (pointing towards Q)
|B| = |BQ| – |BP| = μ0 I / 4√2 r
So, magnetic field at point O has a magnitude μ0I / 4√2 r (directed towards Q).
Teacher's Note: Same sense seen from O means opposite axial fields at O; the net is the difference of the two.
Exam Note: B = μ0I/(4√2 r), towards Q.
Question 11. Answer the following questions. (i) An electron moving horizontally with a velocity of 4 × 104 m/s enters a region of uniform magnetic field of 10–5 T acting vertically upward as shown in the figure. Draw its trajectory and find out the time it takes to come out of the region of magnetic field. (ii) A straight wire of mass 200 g and length 1.5 m carries a current of 2 A. It is suspended in midair by a uniform magnetic field B. What is the magnitude of the magnetic field? [CBSE (F) 2015] [HOTS]
Solution.
(i) The field is directed into the plane of the figure (×). For the electron (negative charge) moving to the right, F = –e(v × B) points downward, so the electron describes a semicircle (clockwise) and comes out of the field region on the same boundary.
Radius r = mv/eB = (9.1 × 10–31 × 4 × 104) / (1.6 × 10–19 × 10–5) ≈ 2.3 × 10–2 m (the region is assumed to be wider than this).
Time to come out = half the period = T/2 = πm/eB = (3.14 × 9.1 × 10–31) / (1.6 × 10–19 × 10–5) ≈ 1.8 × 10–6 s.
(ii) If Ampere’s force acts in upward direction and balances the weight, that is, Fm = mg, i.e. B I l = mg.
B = mg/Il = (0.2 × 10)/(2 × 1.5) = 2/3 ≈ 0.67 T.
Teacher's Note: A half circle in a perpendicular field takes T/2 = πm/eB; suspended wire needs magnetic force equal to weight.
Exam Note: t = πm/eB ≈ 1.8 µs; B = mg/Il ≈ 0.67 T.
Question 12. A uniform magnetic field B is set up along the positive x-axis. A particle of charge ‘q’ and mass ‘m’ moving with a velocity V enters the field at the origin in X-Y plane such that it has velocity components both along and perpendicular to the magnetic field B. Trace, giving reason, the trajectory followed by the particle. Find out the expression for the distance moved by the particle along the magnetic field in one rotation. [CBSE Allahabad 2015] [HOTS]
Solution.
If component vx of the velocity vector is along the magnetic field, and remains constant, the charge particle will follow a helical trajectory, as shown in the figure.
If the velocity component vy is perpendicular to the magnetic field B, the magnetic force acts like a centripetal force qvyB.
So, qvyB = mvy²/r ⇒ vy = qBr/m
Since tangent velocity vy = rω ⇒ rω = qBr/m ⇒ ω = qB/m
Time taken for one revolution, T = 2π/ω = 2πm/qB
and the distance moved along the magnetic field in the helical path is x = vx · T = vx · 2πm/qB.
Teacher's Note: Perpendicular component circles, parallel component drifts uniformly; one turn lasts 2πm/qB, fixing the pitch.
Exam Note: Pitch = vx × 2πm/qB.
Question 13. A particle of charge ‘q’ and mass ‘m’ is moving with velocity V. It is subjected to a uniform magnetic field B directed perpendicular to its velocity. Show that it describes a circular path. Write the expression for its radius. [CBSE (F) 2012] [HOTS]
Solution.
When a particle of charge ‘q’ of mass ‘m’ is directed to move perpendicular to the uniform magnetic field ‘B’ with velocity ‘V’, the force on the charge is F = q(v × B).
This magnetic force acts always perpendicular to the velocity of charged particle. Hence magnitude of velocity remains constant but direction changes continuously. Consequently the path of the charged particle in a perpendicular magnetic field becomes circular. The magnetic force (qvB) provides the necessary centripetal force to move along a circular path. Then,
qvB = mv²/r ⇒ r = mv/qB
Here r = radius of the circular path followed by the charge.
Teacher's Note: Force stays perpendicular to velocity, so speed is constant and the force acts as centripetal force.
Exam Note: Set qvB = mv²/r; r = mv/qB.
Question 14. Answer the following questions. (i) In what respect is a toroid different from a solenoid? Draw and compare the pattern of the magnetic field lines in the two cases. [CBSE (AI) 2011] (ii) How is the magnetic field inside a given solenoid made strong? [CBSE (AI) 2011]
Solution.
(i) A toroid is a solenoid bent into the form of a closed ring. The magnetic field lines of solenoid are straight lines parallel to the axis inside the solenoid.
The magnetic field lines of toroid are circular having common centre.
(ii) Inside a given solenoid, the magnetic field may be made strong by (i) passing large current and (ii) using laminated coil of soft iron (a soft iron core).
Teacher's Note: A toroid has no ends: its field forms closed circles inside the ring, unlike a solenoid with open ends.
Exam Note: Toroid: closed circular lines; solenoid: straight axial lines.
Question 15. Answer the following questions. (i) (a) A circular loop of area A, carrying a current I is placed in a uniform magnetic field B. Write the expression for the torque τ acting on it in a vector form. (b) If the loop is free to turn, what would be its orientation of stable equilibrium? Show that in this orientation, the flux of net field (external field + the field produced by the loop) is maximum. (ii) Find out the expression for the magnetic field due to a long solenoid carrying a current I and having n number of turns per unit length.
Solution.
(i) (a) Torque acting on the current loop τ = m × B = I (A × B), where m = I A.
(b) The loop is in stable equilibrium when its magnetic moment m = I A is in the direction of the external field, i.e. θ = 0°.
Magnetic flux φB = (Bext + BC) · A, where BC is the field of the loop itself (≈ μ0I/2r at its centre, along A).
φmax = [|Bext| + μ0I/2r] |A| cos 0°, where r is radius of the loop. Since cos 0° = 1 is the largest value, the flux is maximum in this orientation.
(ii) Take a rectangular Amperian loop of length h with one side inside the long solenoid and the opposite side outside, where the field is zero. Only the inside side contributes to ∮B·dl, so B h = μ0 (n h I) and hence B = μ0 n I (uniform, along the axis).
Teacher's Note: Stable equilibrium needs m parallel to B, where cos θ = 1 makes the net flux largest.
Exam Note: Stable at θ = 0°; B = μ0nI.
Question 16. A beam of protons passes undeflected with a horizontal velocity v, through a region of electric and magnetic fields, mutually perpendicular to each other and normal to the direction of the beam. If the magnitudes of the electric and magnetic fields are 50 kV/m and 100 mT respectively; calculate the (i) Velocity of the beam. (ii) Force with which it strikes a target on the screen, if the proton beam current is equal to 0.80 mA. [CBSE (AI) 2008] [HOTS]
Solution.
(i) For a beam of charged particles to pass undeflected through crossed electric and magnetic fields, the condition is that electric and magnetic forces on the beam must be equal and opposite, i.e.,
eE = evB ⇒ v = E/B
Given, E = 50 kV/m = 50 × 103 V/m, B = 100 mT = 100 × 10–3 T
∴ v = (50 × 103)/(100 × 10–3) = 5 × 105 m s–1
(ii) Number of protons striking the target per second = I/e = (0.80 × 10–3)/(1.6 × 10–19) = 5 × 1015 s–1. Each proton (mass 1.67 × 10–27 kg) is stopped by the target, so the force equals the rate of change of momentum:
F = (I/e) × mp v = 5 × 1015 × 1.67 × 10–27 × 5 × 105 ≈ 4.2 × 10–6 N.
Teacher's Note: Undeflected beam means eE = evB; the target force is proton arrival rate times momentum per proton.
Exam Note: v = 5 × 105 m/s; F ≈ 4.2 × 10–6 N.
Question 17. Answer the following questions. (i) Obtain the expression for the cyclotron frequency. (ii) A deuteron and a proton are accelerated by the cyclotron. Can both be accelerated with the same oscillator frequency? Give reason to justify your answer. [CBSE Delhi 2017]
Solution.
(i) Suppose the positive charge ion with charge q moves in a dee with a velocity v, then mv²/r = qvB ⇒ r = mv/qB.
Frequency of revolution ν = 1/(Time period T) = v/2πr (∵ T = 2πr/v)
ν = qB/2πm
(ii) No.
The mass of the two particles, i.e., deuteron and proton, is different. Since cyclotron frequency depends inversely on the mass, they cannot be accelerated by the same oscillator frequency.
Teacher's Note: Substituting r = mv/qB into ν = v/2πr removes v, leaving a frequency fixed by q/m alone.
Exam Note: ν = qB/2πm; deuteron and proton need different ν.
Question 18. Answer the following questions. (i) Write the expression for the force F acting on a particle of mass m and charge q moving with velocity V in a magnetic field B. Under what conditions will it move in (a) a circular path and (b) a helical path? [CBSE Delhi 2017] (ii) Show that the kinetic energy of the particle moving in magnetic field remains constant. [CBSE Delhi 2017]
Solution.
(i) F = q (V × B)
(a) When velocity of charged particle and magnetic field are perpendicular to each other charged particle will move in circular path.
(b) When velocity is neither parallel nor perpendicular to the magnetic field charged particle will move in a helical path.
(ii) The force, experienced by the charged particle is perpendicular to the instantaneous velocity, V at all instants. Hence the magnetic force cannot bring any change in the speed of the charged particle. Since speed remains constant, the kinetic energy also remains constant.
Teacher's Note: Magnetic force is always perpendicular to velocity, so it does no work and cannot change speed.
Exam Note: F ⊥ v, so work done is zero.
Question 19. Two identical loops P and Q each of radius 5 cm are lying in perpendicular planes such that they have a common centre as shown in the figure. Find the magnitude and direction of the net magnetic field at the common centre of the two coils, if they carry currents equal to 3 A and 4 A respectively. [CBSE (AI) 2017]
Solution.
Magnetic field at the centre of a circular coil = μ0I / 2R
Magnetic field due to coil P, BP = (μ0 × 3)/(2 × 5 × 10–2) T = 12π × 10–6 T
Magnetic field due to coil Q, BQ = (μ0 × 4)/(2 × 5 × 10–2) T = 16π × 10–6 T
Net magnetic field, B = √(BP² + BQ²) = π √(144 + 256) × 10–6 T = 20π × 10–6 T ≈ 6.3 × 10–5 T
Let the field make an angle θ with the magnetic field due to Q: tan θ = (12π × 10–6)/(16π × 10–6) = 3/4 ⇒ θ = tan–1(3/4) ≈ 37°.
Teacher's Note: Fields are 12π and 16π microtesla at right angles: a 3-4-5 triangle, so the resultant is 20π microtesla.
Exam Note: B = 20π × 10–6 T, tan–1(3/4) from BQ.
Question 20. The figure shows three infinitely long straight parallel current carrying conductors. Find the (i) Magnitude and direction of the net magnetic field at point A lying on conductor 1, (ii) Magnetic force on conductor 2.
Solution.
(i) Field at A due to conductor 2 (current 3I, distance r): B2 = (μ0/4π)(2 × 3I)/r = μ0(6I)/4πr, into the plane of the paper.
Field at A due to conductor 3 (current 4I, distance 3r): B3 = (μ0/4π)(2 × 4I)/3r = (μ0/4π)(8I/3r), out of the plane of the paper.
BA = B2 – B3, into the paper, = (μ0/4π)(10I/3r) = 5μ0I/6πr, into the paper.
(ii) Magnetic force per unit length on wire 2: from wire 1 (opposite currents, repulsion) (μ0/2πr)·I·3I = 3μ0I²/2πr directed away from wire 1; from wire 3 (opposite currents, repulsion) (μ0/2π(2r))·4I·3I = 3μ0I²/πr directed away from wire 3, i.e. towards wire 1.
Net F = 3μ0I²/πr – 3μ0I²/2πr = (3/2) μ0I²/πr per unit length, in the direction of wire 1.
Teacher's Note: Fields of wires 2 and 3 at A oppose, so subtract; on wire 2, wire 3 repels harder.
Exam Note: BA = 5μ0I/6πr inward; force 3μ0I²/2πr per metre towards wire 1.
Question 21. Answer the following questions. (i) State the condition under which a charged particle moving with velocity v goes undeflected in a magnetic field B. (ii) An electron, after being accelerated through a potential difference of 104 V, enters a uniform magnetic field of 0.04 T, perpendicular to its direction of motion. Calculate the radius of curvature of its trajectory. [CBSE (AI) 2017]
Solution.
(i) Force in magnetic field on a charged particle F = q (v × B) ⇒ F = qvB sin θ. If F = 0, then sin θ = 0, θ = 0 or π. So, the magnetic field will be parallel or antiparallel to the velocity of the charged particle.
(ii) For a charged particle moving perpendicular to a constant magnetic field: mv²/r = qvB ⇒ r = mv/qB = p/qB … (i)
If e is accelerated through a potential difference of 104 V, then K.E. of electron = eV ⇒ p²/2m = eV ⇒ p = √(2meV) … (ii)
From (i) and (ii): r = √(2meV)/(eB) = √(2 × 9.1 × 10–31 × 1.6 × 10–19 × 104) / (1.6 × 10–19 × 0.04) = (5.39 × 10–23)/(6.4 × 10–21) m ≈ 8.4 × 10–3 m
Teacher's Note: Accelerating through V gives p = √(2meV); dividing by eB gives the radius.
Exam Note: Undeflected if v ∥ B; r ≈ 8.4 mm.
Question 22. A wire AB is carrying a steady current of 12 A and is lying on the table. Another wire CD carrying 5 A is held directly above AB at a height of 1 mm. Find the mass per unit length of the wire CD so that it remains suspended at its position when left free. Give the direction of the current flowing in CD with respect to that in AB. [Take the value of g = 10 m s–2] [CBSE (AI) 2013]
Solution.
Current carrying conductors attract each other if current flows in the same direction and repel each other if current flows in the opposite direction. For CD to stay suspended, the force on it must be upward, balancing its weight, so it must be a repulsion.
Frepulsion = Weight ⇒ μ0I1I2l/2πr = mg
where r = separation between the wires
m/l = μ0I1I2/2πrg = (2 × 10–7 × 12 × 5)/(1 × 10–3 × 10) = 1.2 × 10–3 kg/m
Current in CD should be in the opposite direction to that in AB.
Teacher's Note: Suspension needs an upward force, so the current must be opposite; equate force per length to weight per length.
Exam Note: m/l = 1.2 × 10–3 kg/m; opposite direction.
Question 23. A rectangular loop of wire of size 2.5 cm × 4 cm carries a steady current of 1 A. A straight wire carrying 2 A current is kept near the loop as shown. If the loop and the wire are coplanar, find the (i) torque acting on the loop and (ii) the magnitude and direction of the force on the loop due to the current carrying wire. [CBSE Delhi 2012]
Solution.
(i) Torque on the loop τ = MB sin θ = |M × B|. The field of the wire is perpendicular to the plane of the loop, so M and B are parallel: τ = 0.
(ii) The sides of 2.5 cm are acted on by equal and opposite forces. For the 4 cm sides (l = 4 cm, r1 = 2 cm, r2 = 2 + 2.5 = 4.5 cm):
|F| = (μ0 I1 I2 l/2π)(1/r1 – 1/r2) = 2 × 10–7 × 2 × 1 × 4 × 10–2 [1/(2 × 10–2) – 1/(4.5 × 10–2)]
= 16 × 10–9 × 100 × [(4.5 – 2)/(2 × 4.5)] = 16 × 10–7 × (2.5/9) ≈ 4.44 × 10–7 N
Direction of force is towards the conductor (attractive), because the nearer side carries current in the same direction as the wire.
Teacher's Note: Wire field is normal to the loop plane, so torque vanishes; the nearer parallel side dominates, giving net attraction.
Exam Note: τ = 0; F ≈ 4.44 × 10–7 N, attractive.
Question 24. Write the expression for the magnetic moment (m) due to a planar square loop of side ‘l’ carrying a steady current I in a vector form. In the given figure this loop is placed in a horizontal plane near a long straight conductor carrying a steady current I1 at a distance l as shown. Give reasons to explain that the loop will experience a net force but no torque. Write the expression for this force acting on the loop. [HOTS][CBSE Delhi 2010]
Solution.
Magnetic moment due to a planar square loop of side l carrying current I is m = I A. For square loop A = l², ∴ m = I l² n̂, where n̂ is unit vector normal to the loop.
The magnetic field due to the current carrying wire at the location of the loop is perpendicular to the plane of the loop. Since the magnetic moment is parallel (or antiparallel) to this field, torque m × B is zero.
Forces on the sides QR and SP are equal and opposite, so net force on these sides is zero.
Force on side PQ (distance l from the wire, current parallel to I1): FPQ = I l × μ0I1/2πl = μ0II1/2π towards the wire (attraction).
Force on side RS (distance 2l, current antiparallel to I1): FRS = I l × μ0I1/2π(2l) = μ0II1/4π away from the wire (repulsion).
Net force F = FPQ – FRS = μ0II1/4π, directed towards the wire. The loop experiences an attractive force but no torque.
Teacher's Note: The nearer side is attracted more than the far side is repelled; field parallel to m gives zero torque.
Exam Note: F = μ0II1/4π attractive; torque zero.
Question 25. Write the expression for the force on a charge moving in a magnetic field. Use this expression to define the SI unit of magnetic field.
Solution.
Force on a charge (q) moving in a magnetic field B with velocity v making an angle θ with the direction of magnetic field (B) is given by
Fm = qvB sin θ
When θ = 90° ⇒ sin θ = 1, so Fm = qvB or B = Fm/qv.
If q = 1 C, v = 1 m/s and Fm = 1 N, then B = 1 T. SI unit of magnetic field is tesla.
Thus, 1 tesla is the magnetic field in which a charge of 1 coulomb moving with a velocity of 1 m/s perpendicular to the field experiences a force of 1 newton (1 T = 1 N A–1 m–1).
Teacher's Note: Setting θ = 90° and unit q, v and F in F = qvB sin θ defines the tesla.
Exam Note: 1 T: 1 C at 1 m/s perpendicular feels 1 N.
Question 26. Define the term magnetic moment of a current loop. Write the expression for the magnetic moment when an electron revolves at a speed v around an orbit of radius ‘r’ in hydrogen atom.
Solution.
Magnetic moment of a current loop: The torque on current loop is τ = MB sin θ, where θ is angle between magnetic moment and magnetic field ⇒ M = τ/(B sin θ).
If B = 1 T, sin θ = 1 or θ = 90° then M = τ.
That is, the magnetic moment of a current loop is defined as the torque acting on the loop when placed in a magnetic field of 1 T such that the loop is oriented with its area vector normal to the magnetic field.
Also, M = IA, i.e., magnetic moment of a current loop is the product of current flowing in the loop and area of loop. Its direction is perpendicular to the plane of the loop and determined by using right hand thumb rule.
Magnetic moment of revolving electron: current I = e/T = ev/2πr and area A = πr², so M = IA = (ev/2πr)(πr²) = evr/2.
Teacher's Note: Moment is the torque per tesla for a loop normal to the field; an orbiting electron gives M = evr/2.
Exam Note: M = IA; electron: M = evr/2.
Question 27. Which of the following will describe the smallest circle when projected with the same velocity perpendicular to the magnetic field B (i) α-particle and (ii) β-particle?
Solution.
Radius of circular path in transverse magnetic field r = mv/qB ∝ m/q for same v and B.
For α-particle (m/q)α = 4mp/2e = 2mp/e, where mp is mass of proton.
For β-particle (m/q)β = (mp/1840)/e = (1/1840)(mp/e)
Clearly β-particle has smallest value of m/q; so β-particle will describe the smallest circle.
Teacher's Note: At equal speed and field, radius follows m/q; a β-particle (electron) has by far the smallest m/q.
Exam Note: β-particle: smallest m/q, smallest circle.
Question 28. A solenoid of length 1.0 m, radius 1 cm and total turns 1000 wound on it, carries a current of 5 A. Calculate the magnitude of the axial magnetic field inside the solenoid. If an electron was to move with a speed of 104 m s–1 along the axis of this current carrying solenoid, what would be the force experienced by this electron?
Solution.
Magnetic field inside a solenoid, B = μ0 n I, where n = N/l = 1000 turns / 1.0 m = 1000 turns/m and I = 5 A.
∴ B = (4π × 10–7) × 1000 × 5 = 20 × 3.14 × 10–4 = 6.28 × 10–3 T, along the axis.
Force experienced by electron: Fm = qvB sin θ. Here q = –e, v = 104 m/s, and θ = angle between v and B = 0°.
∴ Fm = –evB sin 0° = 0 (zero).
Teacher's Note: The electron moves along the field lines, so sin θ = 0 and no magnetic force acts on it.
Exam Note: B = μ0nI = 6.28 × 10–3 T; F = 0.
Question 29. A straight wire carrying a current of 12 A is bent into a semi-circular arc of radius 2.0 cm as shown. What is the magnetic field at O due to (i) straight segments (ii) the semi-circular arc?
Solution.
Magnetic field due to a current carrying element: dB = (μ0/4π) I (δl × r)/r³.
(i) For straight segments, θ = 0 or π ⇒ δl × r = δl r sin 0 n̂ = 0 (O lies on the line of the straight wires). ∴ B1 = 0.
(ii) For semicircular arc, Σ dl = πr, θ = π/2. ∴ B2 = (μ0/4π) I Σ δl sin(π/2)/r² n̂ = (μ0/4π)(I π r/r²) n̂ = μ0I/4r, directed perpendicular to the plane of paper, into the paper (current is clockwise about O).
B2 = (4π × 10–7 × 12)/(4 × 2 × 10–2) ≈ 1.9 × 10–4 T.
Teacher's Note: Straight parts point at O (dl × r = 0); the arc is half a loop, so half of μ0I/2r.
Exam Note: Straight: 0; arc: μ0I/4r ≈ 1.9 × 10–4 T.
Question 30. A semi-circular arc of radius 20 cm carries a current of 10 A. Calculate the magnitude of magnetic field at the centre of the arc.
Solution.
The magnetic field due to a semi-circular arc of radius ‘r’ carrying current (I) at centre is given by ΔB = (μ0/4π) IΔl sin 90°/r² = (μ0/4π) IΔl/r²
The net magnetic field due to whole length of arc will be B = (μ0/4π)(I/r²) Σ Δl
For semi-circular arc ΣΔl = πr ∴ B = (μ0/4π)(I/r²)(πr) = μ0I/4r
Given I = 10 A, r = 20 cm = 0.20 m
∴ B = (4π × 10–7 × 10)/(4 × 0.20) = (4 × 3.14 × 10–7 × 10)/(4 × 0.20) = 1.57 × 10–5 T
Teacher's Note: Every element is perpendicular to the radius, so summing ΔB over length πr gives μ0I/4r.
Exam Note: B = μ0I/4r = 1.57 × 10–5 T.
Question 31. A rectangular current carrying loop is placed 1 cm away from a long straight current-carrying conductor as shown. (i) Will the net force acting on the loop due to straight conductor be attractive or repulsive in nature? Justify your answer. Calculate the magnitude of this force.
Solution.
The net force acting on the loop will be repulsive in nature.
Justification: Part AB of the loop (current opposite to that in the straight conductor) will experience a force of repulsion whereas part CD (current in the same direction) will experience attraction. Parts BC and AD will not experience any force (their forces are equal and opposite). Thus, the overall force will be a force of repulsion because AB is closer to the straight conductor than CD and the force between two current carrying conductors is inversely proportional to the distance between them.
F = (μ0/2π)(I1I2/r) l, with μ0/2π = 2 × 10–7 T m/A.
Force F1 on AB (r = 1 cm): F1 = 2 × 10–7 × (10 × 15)/(1 × 10–2) × 20 × 10–2 = 6 × 10–4 N, away from the conductor.
Force F2 on CD (r = 1 + 10 = 11 cm): F2 = 2 × 10–7 × (10 × 15)/(11 × 10–2) × 20 × 10–2 = 0.545 × 10–4 N, towards the conductor.
Hence, net force on the loop = F1 – F2 = 6 × 10–4 – 0.545 × 10–4 ≈ 5.45 × 10–4 N, repulsive (directed away from the straight conductor).
Teacher's Note: The near side AB is repelled harder than the far side CD is attracted, so the net force is repulsive.
Exam Note: Net F ≈ 5.45 × 10–4 N, repulsive.
Question 32. The magnitude F of the force between two straight parallel current carrying conductors kept at a distance d apart in air is given by F = μ0I1I2/2πd, where I1 and I2 are the currents flowing through the two wires. Use this expression, and the sign convention that the “Force of attraction is assigned a negative sign and Force of repulsion is assigned a positive sign”. Draw graphs showing dependence of F on (i) I1I2 when d is kept constant (ii) d when the product I1I2 is maintained at a constant positive value. (iii) d when the product I1I2 is maintained at a constant negative value. [CBSE Sample Paper] [HOTS]
Solution.
We know that F is an attractive (–ve) force when the currents I1 and I2 are ‘like’ currents i.e. when the product I1I2 is positive.
Similarly F is a repulsive (+ve) force when the currents I1 and I2 are ‘unlike’ currents, i.e., when the product I1I2 is negative.
Now F ∝ (I1I2), when d is kept constant and F ∝ 1/d when I1I2 is kept constant.
The required graphs, therefore, have the forms shown below:
Teacher's Note: With the sign convention, positive I₁I₂ means negative F: line (i) slopes down; (ii) lies below the axis, (iii) above.
Exam Note: (i) falling straight line; (ii) negative 1/d; (iii) positive 1/d.
Question 33. Answer the following questions. (i) Draw the magnetic field lines due to two straight, long, parallel conductors carrying currents I1 and I2 in the same direction. Write an expression for the force acting per unit length on one conductor due to other. Is this force attractive or repulsive? (ii) Figure shows a rectangular current-carrying loop placed 2 cm away from a long, straight, current-carrying conductor. What is the direction and magnitude of the net force acting on the loop? [HOTS]
Solution.
(i) The magnetic field lines due to two current carrying parallel wires are shown in figure (the fields cancel at the neutral point N midway between equal currents). The force between parallel wires per unit length is F/l = μ0I1I2/2πr N/m. For currents in the same direction the force is attractive.
(ii) We know that parallel currents attract and opposite currents repel and F ∝ 1/r. As the wire of the loop carrying opposite current is nearer, the net force acting on the loop is repulsive (away from the wire).
Magnitude: Fnear = 2 × 10–7 × 25 × 15 × 0.25/0.02 = 9.375 × 10–4 N (away); Ffar (r = 12 cm) = 2 × 10–7 × 25 × 15 × 0.25/0.12 = 1.56 × 10–4 N (towards).
Net force = 9.375 × 10–4 – 1.56 × 10–4 ≈ 7.8 × 10–4 N, repulsive.
Teacher's Note: Like currents attract; for the loop, the nearer side with opposite current is repelled more strongly.
Exam Note: Like currents attract; loop net force ≈ 7.8 × 10–4 N repulsive.
Question 34. Two parallel coaxial circular coils of equal radius ‘R’ and equal number of turns ‘N’, carry equal currents ‘I’ in the same direction and are separated by a distance ‘2R’. Find the magnitude and direction of the net magnetic field produced at the mid-point of the line joining their centres. [HOTS]
Solution.
Magnetic field due to a circular coil of radius ‘R’ at a distance x from centre is B = μ0 N I R² / 2(R² + x²)3/2. Here x = R, therefore
B1 = B2 = μ0 N I R² / 2(R² + R²)3/2 = μ0 N I R² / (2 · 2√2 R³) = μ0 N I / 4√2 R
Total magnetic field at centre C due to both coils (equal currents in the same direction, so the fields add): B = B1 + B2 = 2 × μ0NI/4√2R = μ0NI / 2√2 R, directed along the common axis (in the direction given by the right-hand rule for the current).
Teacher's Note: Midpoint is distance R from each coil, and same-sense currents give equal axial fields that add.
Exam Note: B = μ0NI/(2√2 R) along the axis.
Question 35. A rectangular loop of sides 25 cm and 10 cm carrying a current of 15 A is placed with its longer side parallel to a long straight conductor 2.0 cm apart carrying a current of 25 A (fig). What is the net force on the loop? [HOTS]
Solution.
Rectangular loop PQRS is placed near a long straight wire as shown. l = PQ = RS = 25 cm = 0.25 m, b = QR = PS = 10 cm = 0.10 m, r1 = 2 cm = 0.02 m, r2 = 12 cm = 0.12 m
The currents in PQ and XY are antiparallel, so PQ is repelled away from wire XY. This repulsive force is F1 = μ0I1I2l/2πr1 = (4π × 10–7 × 25 × 15 × 0.25)/(2π × 0.02) = 9.375 × 10–4 N
The currents in XY and RS are in the same direction, so wire RS is attracted towards wire XY. This attractive force is F2 = μ0I1I2l/2πr2 = (4π × 10–7 × 25 × 15 × 0.25)/(2π × 0.12) = 1.563 × 10–4 N
The currents in PS and QR are equal and opposite. By symmetry they exert equal and opposite forces (F3 and F4) and hence net force on these sides is zero.
∴ Net force on rectangular loop F = F1 – F2 (repulsive) = 9.375 × 10–4 – 1.563 × 10–4 = 7.812 × 10–4 N (repulsive). The net force is directed away from long wire XY.
Teacher's Note: Forces on the two long sides oppose with 1/r dependence; the nearer, repelled side wins.
Exam Note: Net F = 7.81 × 10–4 N, away from wire.
Question 36. To increase the current sensitivity of a moving coil galvanometer by 50%, its resistance is increased so that the new resistance becomes twice its initial resistance. By what factor does its voltage sensitivity change? [HOTS]
Solution.
Current sensitivity, SC = θ/I = NAB/C
Voltage sensitivity, SV = θ/V = θ/IR = SC/R
When current sensitivity is increased by 50%, the resistance is made twice.
∴ New current sensitivity SC′ = SC + (50/100) SC = 1.5 SC; new resistance R′ = 2R
New voltage sensitivity, SV′ = SC′/R′ = 1.5 SC/2R = 0.75 SV
Clearly, SV′ < SV, i.e. voltage sensitivity decreases, by the factor 0.75 (a decrease of (SV – 0.75SV)/SV × 100% = 25%).
Teacher's Note: Voltage sensitivity is current sensitivity divided by resistance: 1.5 ÷ 2 = 0.75.
Exam Note: SV′ = 0.75 SV; falls by 25%.
Question 37. Write the expression for the force, F acting on a charged particle of charge ‘q’, moving with a velocity V in the presence of both electric field E and magnetic field B. Obtain the condition under which the particle moves undeflected through the fields.
Solution.
Electric force on particle, Fe = qE; magnetic force on particle, Fm = q(v × B); total force, F = Fe + Fm.
F = q(E + v × B)
If a charged particle enters perpendicular to both the electric and magnetic fields then it may happen that the electric and magnetic forces cancel each other and so the particle will pass undeflected. In such a case, F = 0
⇒ q(E + v × B) = 0 ⇒ E = –(v × B) = B × v
⇒ E = Bv sin θ = Bv (when θ = 90°)
⇒ v = E/B (when v, E and B are mutually perpendicular).
Teacher's Note: Net force vanishes when qE = –q(v × B); with mutually perpendicular vectors this reduces to v = E/B.
Exam Note: F = q(E + v × B); undeflected if v = E/B.
Question 38. An α-particle and a proton moving with the same speed enter the same magnetic field region at right angles to the direction of the field. Show the trajectories followed by the two particles in the region of the magnetic field. Find the ratio of the radii of the circular paths which the two particles may describe.
Solution.
Both are positively charged, so both are deflected the same way; the α-particle describes the larger semicircle.
Radius of charged particle in magnetic field r = mv/qB ⇒ r ∝ m/q for same v and B.
rp/rα = (m/q)p/(m/q)α = (mp/e)/((4mp)/2e) = 1/2
So rp : rα = 1 : 2.
Teacher's Note: α has four times the mass but twice the charge, so m/q and radius are doubled.
Exam Note: rp : rα = 1 : 2.
Free study material for Physics
Step-by-Step Xam Idea Solutions for Class 12 Math
Chapter-wise Xam Idea Solutions: Xam Idea Solutions Class 12 Physics Chapter 4 Moving Charges And Magnetism Short Answer Questions II
Explore reliable mathematical solutions for Xam Idea Solutions Class 12 Physics Chapter 4 Moving Charges And Magnetism Short Answer Questions II tailored for Class 12 learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.
Step-by-Step Mathematical Explanations
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Next Steps in Your Mathematics Revision
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.