Step-by-Step Solutions for Class 12 Physics Chapter 15 Communication Systems
Access comprehensive textbook solutions for Chapter 15 Communication Systems using the reference material for Class 12 Physics. Designed to align with the 2026 academic curriculum, these detailed answers help students reinforce core academic concepts and master complex problem-solving methods.
Download Chapter 15 Communication Systems Textbook Solutions PDF
Access the complete solution PDF for Class 12 Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Short Answer Questions II
Question 1. Mention the function of any two of the following used in communication system: (i) Transducer, (ii) Repeater (iii) Bandpass Filter [CBSE Delhi 2014, 2012, South 2016]
Solution.
(i) Transducer: A device which converts one form of energy into another.
(ii) Repeater: It picks up a signal from the transmitter, amplifies it and retransmits it to the receiver.
(iii) Bandpass filter: A bandpass filter rejects low and high frequencies and allows a band of frequencies to pass through.
Teacher's Note: A transducer converts energy, a repeater amplifies and retransmits, a bandpass filter passes a band.
Exam Note: Describe any two functions.
Question 2. Name the three different modes of propagation of electromagnetic waves. Explain, using a proper diagram the mode of propagation used in the frequency range above 40 MHz. [CBSE Delhi 2012]
Solution.
Three mode of propagation of electromagnetic waves are:
(i) Ground waves
(ii) Sky waves
(iii) Space waves
a. LOS (Line of Sight) communication
b. Satellite communication
For figure refer to Basic Concepts Point 6.
Above 40 MHz, the mode of propagation used is via space waves, a space wave travels in a straight line from the transmitting antenna to the receiving antenna. Space waves are used for the line of sight (LOS) communication as well as satellite communication.
Teacher's Note: Waves travel as ground, sky or space waves; above 40 MHz space waves are used.
Exam Note: List modes; sketch space wave diagram.
Question 3. What is ground wave communication? On what factors does the maximum range of propagation in this mode depend? [CBSE (AI) 2011] OR What is ground wave communication? Explain why this mode cannot be used for long distance communication using high frequencies. [CBSE Patna 2015]
Solution.
The mode of wave propagation in which wave glides over the surface of the earth is called ground wave communication.
The maximum range of propagation in this mode depends on
(i) Transmitted power and
(ii) Frequency (less than a few MHz)
At high frequencies, the rate of energy dissipation of the signal increases and the signal gets attenuated over a short distance.
Teacher's Note: Ground waves hug the surface, and higher frequencies suffer greater attenuation.
Exam Note: Define; range factors power and frequency.
Question 4. What is sky wave propagation? Which frequency range is suitable for sky wave propagation and why? Over which range of frequencies can communication through free space using radio waves takes place? [CBSE (F) 2017]
Solution.
A radio wave directed towards the sky and reflected by the ionosphere towards the desired location of the earth is called a sky wave.
The radio waves of frequency range 3 MHz to 30 MHz are suitable for sky wave propagation.
This range of frequencies are reflected by the ionosphere towards the earth. The electromagnetic wave of frequencies higher than 30 MHz penetrates the ionosphere and are not reflected back.
Teacher's Note: Sky waves reflect from the ionosphere only within a limited frequency band.
Exam Note: State 3 to 30 MHz with reason.
Question 5. What is space wave communication? Write the range of frequencies suitable for space wave communication. State the factors which limit its range of propagation. Give two examples of space wave mode of propagation is used. [CBSE Delhi 2013, (AI) 2011, (F) 2014, 2017; North 2016]
Solution.
Space Wave Propagation: The mode of propagation in which radio waves travel, along a straight line, from the transmitting to the receiving antenna.
Frequency Range: Above 40 Mhz
Space wave propagation is used in:
(i) Television broadcast
(ii) Microwave link
(iii) Satellite communication
Limiting Factors
(i) Curvature of the earth
(ii) Insufficient height of the receiving antenna
(iii) LOS distance (> 40 MHz) travel in straight line
Teacher's Note: Space waves travel straight, limited by Earth's curvature and antenna height.
Exam Note: Give definition, range, limits, two examples.
Question 6. Give reasons for the following: (i) For ground wave transmission, size of antenna should be comparable to the wavelength of the signal, e.g., ~λ/4. [CBSE (F) 2013] (ii) Audio signals converted into electromagnetic waves are not transmitted as such directly. (iii) The amplitude of modulating signal is kept less than that of the carrier wave.
Solution.
(i) Ground wave propagation is possible for radio waves of frequency band 540kHz – 1600 kHz (or max. 2 MHz)
If a base band signal of frequency 20 kHz, wavelength of the wave must be λ = 15 km, obviously antenna of size l = 3.75 km is not possible to construct and operate.
If base band signals are translated into high frequency radio wave of frequency ν > 1MHz, then antenna of few metre can be constructed and can be used in sending the information along the ground.
Low size of the antenna is required for waves of short wavelength and hence comparable.
(ii) Audio signals of large wavelength cannot be sent directly, because large size antenna is required.
𝑉𝑚 𝑉𝐶, and its value should be less than 1, otherwise distortion will
(iii) Modulation index, μ =
be produced in the wave.
Teacher's Note: Ground wave antennas need size near the wavelength, audio is impractical directly, and low modulation avoids distortion.
Exam Note: Answer (i) to (iii) separately.
Question 7. What is amplitude modulation? Write its two limitations and two advantages.
Solution.
Amplitude modulation is the process in which amplitude of modulated wave (carrier & information signal) varies in accordance with the amplitude of information signal wave.
Limitations:
(i) Amplitude modulation is noisy.
(ii) It cannot be used for high frequency carrier waves e.g., TV broadcasting.
Advantages:
(i) Production and reception of AM waves is convenient.
(ii) It is cheaper.
Teacher's Note: In AM the carrier amplitude follows the message; it is cheap but noisy.
Exam Note: Define, then two advantages and limitations.
Question 8. Explain briefly the principle of transmitting signals using a satellite. State two main advantages of using a satellite for transmitting signals.
Solution.
Principle of transmitting signals using a satellite: The radio or TV signals are directed to the communication satellite from a point on earth. The transponder receives the signal and reflects it towards the earth which is caught by receiving antenna. Thus, the signal gets transmitted from one place to the other.
(For diagram, refer to Point 6 of Basic Concepts)
Main advantages of satellite communication
(i) The high frequency signals which are not reflected by ionosphere may be transmitted by satellite.
(ii) Satellite communication has a very wide coverage range.
Teacher's Note: A satellite transponder receives uplink signals and retransmits them over wide areas.
Exam Note: State principle, diagram, two advantages.
Question 9. Draw a block diagram of a generalised communication system. Write the functions of each of the following: (a) Transmitter (b) Channel (c) Receiver [CBSE (AI) 2017]
Solution.
A communication system consists of three components: (i) Transmitter (ii) Transmission channel and (iii) Receiver.
(a) Transmitter: A transmitter is an arrangement which processes the incoming message signal so as to make it suitable for transmission through a channel and subsequent reception.
(b) Channel: It carries the message signal from a transmitter to a receiver.
(c) Receiver: A receiver extracts the desired message signals from the received signals at the channel output.
Teacher's Note: Every communication system has a transmitter, a channel and a receiver, with noise in the channel.
Exam Note: Draw the block diagram and give each function.
Question 10. Define the term modulation. Draw a block diagram of a simple modulator for obtaining AM signal. OR Draw a block diagram of a simple modulator to explain how the AM wave is produced. Can the modulated signal be transmitted as such? Explain. [CBSE (F) 2014; Guwahati 2015]
Solution.
Modulation is the process of super imposition of low frequency message signal over a high frequency carrier wave.
Amplitude Modulation: The block diagram is shown in fig.
Explanation: The AM wave has to be fed to power amplifier to provide the necessary power. It is then fed to the antenna for transmission.
Teacher's Note: Modulation superimposes a message signal on a high-frequency carrier before transmission.
Exam Note: Define modulation; draw the modulator block diagram.
Question 11. Answer the following questions: (i) How is amplitude modulation achieved? (ii) The frequencies of two side bands in an AM wave are 640 kHz and 660 kHz respectively. Find the frequencies of carrier and modulating signal. What is the bandwidth required for amplitude modulation? [CBSE (AI) 2017]
Solution.
(i) In amplitude modulation, the amplitude of the carrier varies in accordance with the information signal. At the input of the transistor as CE, the low frequency modulating signals are superimposed on high frequency carrier wave. The output signal is carrier signal varying in amplitude in accordance with biasing modulation voltage. Thus, AM wave is produced. For diagram refer to the above question.
(ii) Frequencies of side bands are fc + fm = 660 kHz ... (i) and fc − fm = 640 kHz ... (ii)
Adding (i) and (ii): 2fc = 660 kHz + 640 kHz, so fc = 650 kHz.
Now, fm = 660 kHz − 650 kHz = 10 kHz.
Bandwidth required for amplitude modulation = Upper side band − Lower side band = (fc + fm) − (fc − fm) = 2fm = 2 × 10 kHz = 20 kHz.
Teacher's Note: Side bands lie at fc ± fm, so fc is their average and bandwidth is 2fm.
Exam Note: Add and subtract the side bands.
Question 12. Write three important factors which justify the need of modulating a message signal. Show diagrammatically how an amplitude modulated wave is obtained when a modulating signal is superimposed on a carrier wave. [CBSE Delhi 2013, 2016; Panchkula 2015]
Solution.
Three factors for the need of modulating a message signal:
(i) If λ is the wavelength of the signal then the antenna should have a length at least λ/4. For an electromagnetic wave of frequency 20 kHz, the wavelength λ is 15 km. Such a long antenna is not possible to construct and operate. So, there is need to modulate the wave in order to reduce the height of antenna to a reasonable height.
(ii) The power radiated by a linear antenna (length l) is proportional to (l/λ)2. This shows that power radiated increases with decreasing λ. So, for effective power radiation by antenna, there is need to modulate the wave.
(iii) To avoid mixing up of signals from different transmitters.
Diagrammatic representation:
Teacher's Note: Modulation allows short antennas, better radiated power, and separate channels for each transmitter.
Exam Note: Give three factors; draw carrier, signal and AM wave.
Question 13. (a) Define the term ‘modulation index,’ used in communication system. Why is its value kept less than or equal to one? (b) A message signal of frequency 10 kHz and peak voltage of 10 V is used to modulate a carrier frequency of 1 MHz and peak voltage of 10V. Determine the (i) modulation index, and (ii) side bands produced. [CBSE (F) 2017]
Solution.
(a) Modulation index: It is the ratio of peak value of modulating signal to the peak value of carrier wave. It is kept less than or equal to 1 to avoid distortion. Physical significance: It signifies the level of distortion or noise. A lower value of modulation index indicates a lower distortion in the transmitted signal.
(b) (i) Modulation index μ = Vm/Vc = 10 V/10 V = 1
(ii) Side bands: fc + fm = 1000 kHz + 10 kHz = 1010 kHz (upper) and fc − fm = 1000 kHz − 10 kHz = 990 kHz (lower).
Teacher's Note: Modulation index is peak message voltage divided by peak carrier voltage.
Exam Note: Define it; compute 1 and 990, 1010 kHz.
Question 14. Figure shows a block diagram of a transmitter. Identify the boxes ‘X’ and ‘Y’ and write their functions. [CBSE (F) 2012]
Solution.
X → Amplitude Modulator, Y → Power Amplifier
Function of X: The original message signal has very small energy and dies out very soon if transmitted directly as such. Hence, these signals are modulated by mixing with very high frequency waves (carrier wave) by modulator.
Function of Y: The signal cannot be transmitted as such because they get weaken after travelling long distance. Hence, use of power amplifier provides them necessary power before feeding the signal to the transmitting antenna.
Teacher's Note: The modulator mixes the message with a carrier; the power amplifier boosts the signal.
Exam Note: Identify X, Y; state one function each.
Question 15. What does the process of detection of amplitude modulated wave mean? The amplitude modulated carrier wave of angular frequency ωc, (ωc + ωm) and (ωc − ωm), where ωm is the angular frequency of the modulating signal. Discuss, in brief, with the help of a block diagram the essential details of a simple method used for ‘detecting’ the modulating signal from this modulated carrier wave. OR Draw a block diagram of a detector for AM signal and show, using necessary processes and the waveforms, how the original message signal is detected from the input AM wave. [CBSE Delhi 2015]
Solution.
Detection is the process of recovery of the modulating signal from the modulated carrier wave.
The amplitude modulated carrier wave contains waves of frequencies ωc, ωc + ωm and ωc − ωm. The block diagram of a simple method is shown below:
In order to obtain the original message signal m(t) of angular frequency ωm, the modulated signal [form (a)] is passed through a rectifier to produce the output shown in fig. (b). The envelope of signal (b) is the message signal. This is separated by passing it through envelope detector (which may consist of simple R.C. circuit).
Teacher's Note: Detection recovers the message by rectifying the AM wave and then taking its envelope.
Exam Note: Show rectifier, envelope detector and three waveforms.
Question 16. Answer the following questions: (i) Distinguish between ‘Analog and Digital signals’. (ii) Explain briefly two commonly used applications of the internet. [CBSE Delhi 2012, Panchkula 2015]
Solution.
(i) A signal that varies continuously with time (e.g., sine wave form) is called an analog signal. A signal that is discrete is called a digital signal. The presence of signal is denoted by digit 1 and absence is denoted by digit 0. These are represented by:
(ii) Uses of Internet: email, e-banking, e-shopping, e-ticketing, chatting, surfing, file transfer, etc.
Teacher's Note: Analog signals vary continuously; digital signals take discrete values such as 0 and 1.
Exam Note: Contrast the two signals; name two internet uses.
Question 17. By what percentage will the transmission range of a TV tower be affected when the height of the tower is increased by 21%? [CBSE Delhi 2009]
Solution.
Transmission range of TV tower d = √(2Rh), so d ∝ √h.
New height h’ = h + 0.21h = 1.21h
d’/d = √(h’/h) = √1.21 = 1.1
So the range increases by 10%.
Teacher's Note: Range varies as the square root of tower height.
Exam Note: Use d proportional to root h.
Question 18. A carrier wave of frequency 1.5 MHz and amplitude 50 V is modulated by a sinusoidal wave of frequency 10 kHz producing 50% amplitude modulation. Calculate the amplitude of the AM wave and frequencies of the side bands produced. [CBSE Allahabad 2015]
Solution.
Carrier amplitude Ac = 50 V, modulation index μ = 0.5
Amplitude of modulating signal Am = μAc = 0.5 × 50 = 25 V. So the AM wave amplitude varies between Ac − Am = 25 V and Ac + Am = 75 V.
Frequencies of side bands: fc + fm = 1500 kHz + 10 kHz = 1510 kHz and fc − fm = 1500 kHz − 10 kHz = 1490 kHz.
Teacher's Note: Message amplitude is modulation index times carrier amplitude; side bands lie at carrier plus and minus message frequency.
Exam Note: Find Am, then fc ± fm.
Question 19. A signal of 5 kHz frequency is amplitude modulated on a carrier wave of frequency 2 MHz. What are the frequencies of the side bands produced? [CBSE North 2016]
Solution.
Maximum frequency = 5 kHz + 2 MHz = 5 × 103 + 2 × 106 = (5 + 2000) × 103 = 2005 × 103 Hz = 2005 kHz
Minimum frequency = 2 MHz − 5 kHz = 2 × 106 − 5 × 103 = (2000 − 5) × 103 = 1995 × 103 Hz = 1995 kHz
Teacher's Note: Side bands appear at carrier frequency plus and minus signal frequency.
Exam Note: Give 2005 kHz and 1995 kHz.
Question 20. We do not choose to transmit an audio signal by just directly converting it to an e.m. wave of the same frequency. Give two reasons for the same.
Solution.
(i) Size of Antenna: For efficient transmission and reception of a signal, the height of the antenna must be λ/4. For example, for an audio signal of frequency 15 kHz, λ = c/ν = (3 × 108)/(15 × 103) = 20 km, so the antenna height would be λ/4 = 5 km, which is impossible.
(ii) Simultaneous transmission of signals by different transmitters can overlap, thus causing the disturbance at the receiver end.
Teacher's Note: Audio waves need very long antennas and would mix with other transmitters.
Exam Note: Give antenna size and signal overlap reasons.
Question 21. Answer the following questions: (i) A TV transmitter has a range of 50 km. What is the height of the TV transmission tower? Radius of earth Re = 6.4 × 106 m. (ii) A TV tower has a height of 500 m at a given place. If radius of earth is 6400 km, what is its coverage range?
Solution.
(i) Here d = 50 km = 50 × 103 m. Since d = √(2Reh), h = d2/(2Re) = (50 × 103)2/(2 × 6.4 × 106) = 2.5 × 109/(1.28 × 107) ≈ 195 m.
(ii) Coverage range of TV tower d = √(2Reh) = √(2 × 6.4 × 106 × 500) = √(6.4 × 109) = 8 × 104 m = 80 km.
Teacher's Note: TV tower range follows d = √(2Rh).
Exam Note: Rearrange d = √(2Rh) for height.
Question 22. An optical communication system is operating at wavelength 800 nm. If only 1% of the optical source frequency is used as channel band width for optical communication; then find the number of channels that can be accommodated for transmitting (i) audio signals requiring a band width of 8 kHz and (ii) Video TV signals requiring a band width of 4.5 MHz. Support your answer with suitable calculations.
Solution.
Frequency of optical source ν = c/λ = (3 × 108)/(800 × 10−9) = 3.75 × 1014 Hz.
Channel bandwidth available = 1% of ν = 3.75 × 1012 Hz.
(i) Number of audio channels = (3.75 × 1012)/(8 × 103) ≈ 4.7 × 108.
(ii) Number of video TV channels = (3.75 × 1012)/(4.5 × 106) ≈ 8.3 × 105.
Teacher's Note: Divide the usable bandwidth by the bandwidth needed for each channel.
Exam Note: Find source frequency, take 1%, then divide.
Question 23. What would be the modulation index for an amplitude modulated wave for which the maximum amplitude is ‘a’ while the minimum amplitude is ‘b’?
Solution.
Modulation index is given by ma = Em/Ec ... (i)
Maximum amplitude of modulated wave a = Ec + Em ... (ii)
Minimum amplitude of modulated wave b = Ec − Em ... (iii)
From (ii) and (iii), Ec = (a + b)/2, Em = (a − b)/2
∴ ma = Em/Ec = [(a − b)/2]/[(a + b)/2] = (a − b)/(a + b)
Teacher's Note: Maximum and minimum amplitudes give carrier and message amplitudes by sum and difference.
Exam Note: Show derivation ending (a − b)/(a + b).
Question 24. Draw a plot of variation of amplitude versus ω for an amplitude modulated wave. Define modulation index. State its importance for effective amplitude modulation.
Solution.
Plot of variation of amplitude versus ω for amplitude modulated wave is shown in figure.
Modulation Index: The ratio of amplitude of modulating signal to the amplitude of carrier wave is called modulation index, i.e., ma = Em/Ec.
For effective amplitude modulation, the modulation index determines the distortions, so its value is kept ≤ 1 for avoiding distortions.
Teacher's Note: An AM wave has a carrier and two side bands of height maEc/2.
Exam Note: Draw three lines; define ma; give limit one.
Question 25. A ground receiver station is receiving signals at (i) 5 MHz and (ii) 100 MHz, transmitted from a ground transmitter at a height of 300 m located at a distance of 100 km. Identify whether the signals are coming via space wave or sky wave propagation or satellite transponder. Radius of earth = 6400 km; maximum electron density in ionosphere, Nmax = 1012 m−3.
Solution.
Maximum frequency reflected by the ionosphere (critical frequency) fc = 9√Nmax = 9 × √(1012) = 9 × 106 Hz = 9 MHz.
(i) The 5 MHz signal is less than 9 MHz, so it is reflected by the ionosphere. It is received via sky wave propagation.
(ii) The 100 MHz signal is greater than 9 MHz, so it penetrates the ionosphere and is not a sky wave. Range of space wave from the 300 m transmitter d = √(2Rh) = √(2 × 6.4 × 106 × 300) ≈ 62 km, which is less than 100 km. So it is not a space wave either. Hence the 100 MHz signal is coming via a satellite transponder.
Teacher's Note: Frequencies below the critical frequency are reflected; higher ones need space waves or satellites.
Exam Note: Compare each frequency with 9 MHz and range.
Question 26. A (sinusoidal) carrier wave C(t) = AC sin ωct is amplitude modulated by a (sinusoidal) message signal m(t) = Am sin ωmt. Write the equation of the (amplitude) modulated signal. Use this equation to obtain the values of the frequencies of all the sinusoidal waves present in the modulated signal.
Solution.
The equation of the (amplitude) modulated signal is Cm(t) = (Ac + Am sin ωmt) sin ωct
This can be rewritten as Cm(t) = Ac(1 + μ sin ωmt) sin ωct, where μ = Am/Ac.
Cm(t) = Ac sin ωct + (μAc/2) cos(ωc − ωm)t − (μAc/2) cos(ωc + ωm)t
So the modulated signal contains three sinusoidal waves, of frequencies ωc, ωc − ωm and ωc + ωm.
Teacher's Note: Expanding the product shows a carrier and two side-band frequencies.
Exam Note: Write Cm(t), expand, list three frequencies.
Free study material for Physics
Download Xam Idea Solutions for Class 12 Math PDF
Download Xam Idea Solutions for Class 12
Explore reliable mathematical solutions for Xam Idea Solutions Class 12 Physics Chapter 15 Communication Systems Short Answer Questions II tailored for Class 12 learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.
Detailed Calculation Guides for Class 12
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Next Steps in Your Mathematics Revision
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.