Download Class 12 Physics Textbook Solutions: Chapter 14 Electronic Devices
Access comprehensive textbook solutions for Chapter 14 Electronic Devices using the reference material for Class 12 Physics. Designed to align with the 2026 academic curriculum, these detailed answers help students reinforce core academic concepts and master complex problem-solving methods.
Access Textbook Answers and Solutions
Access the complete solution PDF for Class 12 Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Long Answer Questions
Question 1. (a) State briefly the processes involved in the formation of p-n junction explaining clearly how the depletion region is formed. (b) Using the necessary circuit diagrams, show how the V–I characteristics of a p-n junction are obtained in (i) forward biasing (ii) reverse biasing. How are these characteristics made use of in rectification? Describe briefly the following terms: (i) 'Minority carrier injection' in forward bias (ii) 'Breakdown voltage' in reverse bias.
Solution.
(a) Two processes occur during the formation of a p-n junction: diffusion and drift. Due to the concentration gradient across the p and n sides of the junction, holes diffuse from the p-side to the n-side (p → n) and electrons diffuse from the n-side to the p-side (n → p). This movement leaves behind ionised acceptors (negative, immobile) on the p-side and ionised donors (positive, immobile) on the n-side of the junction. This space charge region on either side of the junction together is known as the depletion region.
(b) The circuit arrangements for studying the V–I characteristics of a diode are shown below. For different values of the voltage the value of the current is noted. A graph between V and I is obtained as shown.
From the V–I characteristic of a junction diode it is clear that it allows current to pass only when it is forward biased. So if an alternating voltage is applied across a diode, the current flows only in that part of the cycle when the diode is forward biased. This property is used to rectify alternating voltages.
(i) Minority carrier injection: Due to the applied forward voltage, electrons from the n-side cross the depletion region and reach the p-side (where they are minority carriers). Similarly, holes from the p-side cross the junction and reach the n-side (where they are minority carriers). This process under forward bias is known as minority carrier injection.
(ii) Breakdown voltage: It is the critical reverse bias voltage at which the reverse current increases suddenly and sharply.
Teacher's Note: Forward bias conducts, reverse bias blocks; breakdown voltage is where reverse current suddenly rises.
Exam Note: Draw both circuits and the V-I curve.
Question 2. Explain, with the help of a circuit diagram, the working of a p-n junction diode as a half-wave rectifier.
Solution.
Working
(i) During the positive half cycle of the input alternating voltage, the diode is forward biased and a current flows through the load resistor RL, so we get an output voltage.
(ii) During the negative half cycle of the input alternating voltage, the diode is reverse biased and it does not conduct (the current is negligible), so there is no output voltage.
Hence the ac voltage is rectified into a pulsating, unidirectional voltage.
Teacher's Note: Diode conducts only in positive half cycles, giving pulsating unidirectional output.
Exam Note: Explain both half cycles with waveforms.
Question 3. State the principle of working of p-n diode as a rectifier. Explain with the help of a circuit diagram, the use of p-n diode as a full wave rectifier. Draw a sketch of the input and output waveforms. Which characteristic property makes the junction diode suitable for rectification?
Solution.
Rectification: Rectification means conversion of ac into dc. A p-n diode acts as a rectifier because an ac changes polarity periodically and a p-n diode allows current to pass only when it is forward biased. This property makes the junction diode suitable for rectification.
Working: The ac input voltage across the secondary S1 and S2 changes polarity after each half cycle. Suppose during the first half cycle of the input ac signal, the terminal S1 is positive relative to the centre tap O and S2 is negative relative to O. Then diode D1 is forward biased and diode D2 is reverse biased. Therefore, diode D1 conducts while diode D2 does not. The current (i1) due to D1 in the load resistance RL is directed from A to B.
In the next half cycle, the terminal S1 is negative and S2 is positive relative to the centre tap O. Diode D1 is reverse biased and diode D2 is forward biased. Therefore, D2 conducts while D1 does not. The current (i2) due to D2 in the load resistance RL is still from A to B.
Thus the current in the load resistance RL is in the same direction for both half cycles of the input ac voltage, and the output current is a continuous series of unidirectional pulses.
In a full wave rectifier, if the input frequency is f hertz, then the output frequency is 2f hertz, because for each cycle of input two positive half cycles of output are obtained.
Teacher's Note: Each diode conducts in alternate half cycles, so output has frequency twice the input.
Exam Note: Use centre-tap circuit; mention output frequency 2f.
Question 4. Explain, how the heavy doping of both p-and n-sides of a p-n junction diode results in the electric field of the junction being extremely high even with a reverse bias voltage of a few volts.
Solution.
If the p-type and n-type semiconductors are heavily doped, then due to the diffusion of electrons from the n-region to the p-region, and of holes from the p-region to the n-region, a depletion region is formed whose width is of the order of less than 1 μm. A reverse bias voltage of about 5 V across so thin a region produces a very large electric field.
E = ΔV/Δx = 5 V/1 μm = 5 V/(10⁻⁶ m) ≈ 5 × 10⁶ V/m
Teacher's Note: Thin depletion layer across a few volts gives a field of about 5 × 10⁶ V/m.
Exam Note: Relate narrow depletion width to E = V/d.
Question 5. Why is a Zener diode considered as a special purpose semiconductor diode? Draw the I–V characteristic of a zener diode and explain briefly how reverse current suddenly increases at the breakdown voltage. How is Zener diode fabricated? What causes the setting up of high electric field even for small reverse bias voltage across the diode? Describe with the help of a circuit diagram, the working of Zener diode as a voltage regulator.
Solution.
A Zener diode is considered a special purpose semiconductor diode because it is designed to operate under reverse bias in the breakdown region.
A Zener diode is fabricated by heavy doping of both its p and n sections. Since the doping is high, the depletion layer becomes very thin. Hence the electric field (E = V/d) becomes high even for a small reverse bias.
The reverse current is due to the flow of electrons (minority carriers) from p → n and holes from n → p. As the reverse bias voltage is increased, the electric field at the junction becomes significant. When the reverse bias voltage V = VZ, the electric field is strong enough to pull valence electrons from the host atoms on the p-side, which are accelerated to the n-side. These electrons cause a large current at breakdown.
Working as a voltage regulator: The unregulated dc output of a rectifier is connected to the Zener diode through a series resistance RS such that the Zener diode is reverse biased, and the load RL is connected across the diode.
If the reverse bias voltage reaches the Zener voltage VZ, there is a large change in current for an almost insignificant change in voltage, so the diode voltage remains constant. If the unregulated input voltage increases, the current through RS and the diode also increases. This increases the voltage drop across RS without any change in the voltage across the Zener diode. Thus we have a constant regulated voltage across the load resistor RL. Similarly, when the input decreases, the drop across RS decreases and VZ is unchanged.
Teacher's Note: Heavy doping thins the depletion layer; Zener holds constant voltage across the load.
Exam Note: Cover fabrication, breakdown mechanism and regulator action.
Question 6. In the figure given alongside, is (i) the emitter and (ii) the collector forward or reverse biased? With the help of a circuit diagram explain the action of npn transistor. (The terminals are at C = +1 V, B = 0 V and E = –2 V.)
Solution.
The given transistor is n-p-n, since the emitter arrow points away from the base. The base is at 0 V and the emitter at –2 V, so the emitter-base junction is forward biased (VBE = +2 V). The collector is at +1 V and the base at 0 V, so the collector-base junction is reverse biased (VCB = +1 V).
Action of n-p-n transistor: An n-p-n transistor is equivalent to two p-n junction diodes placed back to back with their very thin p-regions common. The two batteries VEE and VCC provide the emitter and collector supply respectively. The transistor works only when its emitter-base junction is forward biased and its collector-base junction is reverse biased.
Base current and collector current: Under forward bias of the emitter-base junction, the electrons of the emitter and the holes of the base move towards the junction. As the base is very thin, most electrons (about 98%) from the emitter cross the base and reach the collector, while only a few (about 2%) combine with holes of the base. Each hole lost in the base is replaced by the break of a covalent bond, and the electron released is attracted by the positive terminal of VEE, giving rise to a small base current IB.
The electrons that enter the collector are attracted by the positive terminal of VCC, so a current flows in the collector circuit. In addition, minority carriers under the reverse bias of the base-collector junction give a small leakage current. Thus IC = Inc + Ileakage.
Emitter current: The electrons entering the batteries from the base and the collector are replaced by an equal number of electrons that enter the emitter from VEE, which gives the emitter current.
Relation between the currents: By Kirchhoff's first law, IE = IB + IC.
Teacher's Note: Emitter-base forward and collector-base reverse biased: n-p-n with E at lowest potential.
Exam Note: Check junction potentials, then describe carrier flow.
Question 7. Draw the circuit diagram to study the characteristics of npn transistor in common emitter configuration. Sketch typical (i) input characteristics (ii) output characteristics for such a configuration. Explain how the current gain of transistor is calculated from output characteristics. With the help of these characteristics define (i) input resistance, (ii) current amplification factor.
Solution.
Characteristic curves: The circuit for determining the static characteristic curves of an n-p-n transistor in common-emitter configuration is shown.
(i) Input characteristics are obtained by recording the base current IB for different values of the base-emitter voltage VBE at constant collector-emitter voltage VCE.
(ii) Output characteristics are obtained by recording the collector current IC for different values of VCE at constant base current IB.
The output characteristics show that when VCE is increased from zero, IC increases only up to about 1 V and then becomes almost constant and independent of VCE. The value of VCE up to which IC changes is called the knee voltage.
Input resistance: The ratio of the change in base-emitter voltage to the change in base current at constant collector-emitter voltage: ri = (ΔVBE/ΔIB) at constant VCE.
Current amplification factor: The ratio of the change in collector current to the change in base current at constant collector-emitter voltage: βac = (ΔIC/ΔIB) at constant VCE.
Determination of current gain: We take the active region of the output characteristics, i.e. the region where IC is almost independent of VCE. At a fixed VCE we choose any two characteristic curves for given values of IB and read the two corresponding values of IC. Then βac = ΔIC/ΔIB.
Teacher's Note: Input curves fix r_i; output curves at constant V_CE give β_ac = ΔI_C/ΔI_B.
Exam Note: Draw circuit and both curves; define r_i and β_ac.
Question 8. Draw the transfer characteristics of a base biased transistor in common emitter configuration. Explain briefly the meaning of the term active region in these characteristics. For what practical use, do we use the transistor in this active region? Explain clearly how the active region of the Vo versus Vi curve in a transistor is used as an amplifier.
Solution.
Transfer characteristics are the curves representing the variation of the output voltage Vo (= VCE) with the input voltage Vi (the base bias). The circuit is shown below.
For plotting the curve, the input voltage Vi is changed in small steps and the corresponding output voltage Vo is measured. The curve obtained is shown.
For small Vi (below about 0.6 V for silicon) the transistor is in the cut-off region and Vo = VCC. As Vi increases further, IC rises and Vo falls almost linearly; this part is the active region. For large Vi the transistor goes into saturation and Vo is nearly zero.
In the active region, a small increase of Vi results in a large (almost linear) increase in IC. This increases the voltage drop across RC, so Vo = VCC – ICRC decreases by a larger amount. A small change in Vi thus appears as an amplified, inverted change in Vo. Hence, in the active region the transistor is used as an amplifier.
Switching circuits are designed so that the transistor does not remain in the active state; it works only in the cut-off and saturation states.
Teacher's Note: Active region has nearly linear V_o against V_i with negative slope: amplification.
Exam Note: Name cut-off, active and saturation regions.
Question 9. Draw a labelled circuit diagram of a common emitter amplifier using a p-n-p transistor. Define the term voltage gain and write an expression for it. Explain how the input and output voltages are out of phase by 180° for a common-emitter transistor amplifier.
Solution.
Common-emitter transistor amplifier: The circuit for a p-n-p transistor is shown. The emitter is common to both the input (emitter-base) and output (collector-emitter) circuits and is grounded. The emitter-base junction is forward biased and the collector-base junction is reverse biased.
In a common-emitter circuit, the collector current is controlled by the base current. A very small change in base current produces a much larger change in collector current, so large current gains are possible. The ac current gain is βac = ΔIC/ΔIB (at constant VCE), generally greater than 20.
Voltage gain: It is the ratio of the change in output voltage to the change in input voltage, Av = ΔVo/ΔVi = –βacRL/ri.
Phase difference: When the positive half cycle is fed to the input circuit, it opposes the forward bias, so the collector current decreases. This decreases the voltage drop across the load RL and makes the collector voltage more negative. Thus, when the input varies through a positive half cycle, the output voltage varies through a negative half cycle, and vice versa. The output voltage is therefore in antiphase with the input signal, i.e. 180° out of phase.
Teacher's Note: Positive input half cycle lowers I_C, making collector more negative: 180° phase shift.
Exam Note: Define gain, give formula, explain antiphase.
Question 10. (a) Differentiate between three segments of a transistor on the basis of their size and level of doping. (b) How is a transistor biased to be in active state? (c) With the help of necessary circuit diagram describe briefly how npn transistor in CE configuration amplifies a small sinusoidal input voltage. Write the expression for ac current gain. What is the phase difference between the input signal and output voltage? Draw the input and output waveforms. Write the expression for its voltage gain. State two reasons why a common emitter amplifier is preferred to a common base amplifier.
Solution.
(a) Emitter: moderate in size and heavily doped. Base: very thin and lightly doped. Collector: larger in size than the emitter and moderately doped.
(b) A transistor is in the active state when its emitter-base junction is suitably forward biased and its base-collector junction is suitably reverse biased.
(c) The circuit of a common emitter amplifier using an n-p-n transistor is shown.
Working: If a small sinusoidal voltage of amplitude Vs is superposed on the dc bias (by connecting it in series with the base supply VBB), the base current has sinusoidal variations superposed on the dc base current IB. As a consequence the collector current also has sinusoidal variations superimposed on its dc value IC, which produces corresponding amplified changes in the output voltage Vo. The ac variations at the input and output terminals are taken by blocking the dc voltage with large capacitors.
The ac current gain is βac = (ΔIC/ΔIB) at constant VCE. The voltage gain is Av = ΔVo/ΔVi = –βacRL/ri. The phase difference between the input signal and the output voltage is 180°. The waveforms are shown.
Reasons for using a common emitter amplifier: (i) The voltage gain is quite high. (ii) The voltage gain is uniform over a wide frequency range, or the power gain is high.
Teacher's Note: Emitter heavily doped, base thin and light, collector large; CE output is inverted.
Exam Note: Give doping order, biasing, amplifier circuit and 180° phase.
Question 11. Show the output waveforms (Y) for the following inputs A and B of (i) OR gate (ii) NAND gate.
Solution.
The OR gate gives output 1 when at least one input is 1; the NAND gate gives output 0 only when both inputs are 1 (between t3 and t4).
Teacher's Note: OR is high if any input is high; NAND is low only when both are high.
Exam Note: Tabulate A and B interval by interval.
Question 12. Draw a simple circuit of a CE transistor amplifier. Explain its working. Show that the voltage gain Av of the amplifier is given by Av = –βacRL/ri, where βac is the current gain, RL is the load resistance and ri is the input resistance of the transistor. What is the significance of the negative sign in the expression for the voltage gain?
Solution.
Circuit diagram of a CE transistor amplifier:
When an ac input signal Vi (to be amplified) is superimposed on the bias VBB, the output, measured between collector and ground, is an amplified signal.
First assume Vi = 0. Applying Kirchhoff's law to the output loop: VCC = VCE + ICRL. Similarly the input loop gives VBB = VBE + IBRB.
When the signal Vi is applied, the base current changes by ΔIB, and Vi = riΔIB, where ri = ΔVBE/ΔIB is the input resistance.
The change in IB causes a change in IC: βac = ΔIC/ΔIB.
As VCC is constant, ΔVCC = ΔVCE + RLΔIC = 0, so ΔVCE = –RLΔIC. The change in VCE is the output voltage Vo:
Vo = –RLΔIC = –βacΔIBRL
The voltage gain of the amplifier is therefore
Av = Vo/Vi = –βacΔIBRL/(riΔIB) = –βacRL/ri
The negative sign shows that the output voltage and input voltage have a phase difference of π (180°).
Teacher's Note: ΔV_CE = –R_L ΔI_C and V_i = r_i ΔI_B give A_v = –β R_L/r_i.
Exam Note: Derive from the collector loop; negative sign means 180° shift.
Question 13. In the figure, the circuit symbol of a logic gate (OR symbol with inputs A and B and output Y) and two input waveforms A and B are shown. (i) Name the logic gate. (ii) Write its truth table. (iii) Give the output waveform.
Solution.
(i) The logic gate shown is an OR gate.
(ii) Truth table of the OR gate:
| A | B | Y = A + B |
|---|---|---|
| 0 | 0 | 0 |
| 0 | 1 | 1 |
| 1 | 0 | 1 |
| 1 | 1 | 1 |
(iii) The input waveforms A and B are discrete square waves; their levels change at the points a, b, c, … h.
Between a and b, A = 1, B = 1 → Y = 1
Between b and c, A = 0, B = 0 → Y = 0
Between c and d, A = 0, B = 1 → Y = 1
Between d and e, A = 1, B = 0 → Y = 1
Between e and f, A = 1, B = 1 → Y = 1
Between f and g, A = 0, B = 0 → Y = 0
Between g and h, A = 0, B = 1 → Y = 1
Accordingly, the waveform Y is as shown.
Teacher's Note: Y is 1 whenever either A or B is 1.
Exam Note: Tabulate each interval, then draw Y.
Question 14. Draw the output signals C1 and C2 in the given combination of gates. The input waveforms A and B (shown in the figure) are: A = 1 for 0 to 2 s, 0 for 2 to 3 s, 1 for 3 to 4 s, 0 afterwards; B = 1 for 1 to 3 s and 0 otherwise.
Solution.
Upper circuit: the first two NAND gates (inputs joined) act as NOT gates, giving Ā and B̄. The third NAND gives Ā·B̄ = A + B. The last NAND (inputs joined) acts as a NOT gate, so C1 = A + B, a NOR output.
Lower circuit: the first two NOR gates (inputs joined) act as NOT gates, giving Ā and B̄. The third NOR gives C2 = Ā + B̄ = A·B, an AND output.
C1 is high only after 4 s, when A = B = 0. C2 is high only between 1 s and 2 s, when A = B = 1.
Teacher's Note: Upper circuit is NOR, lower circuit is AND, built from NAND and NOR gates.
Exam Note: Reduce each gate chain with De Morgan's theorem.
Question 15. Input signals A and B are applied to the input terminals of the 'dotted box' set-up shown here. Let Y be the final output signal from the box. Draw the wave forms of the signals labelled as C1 and C2 within the box, giving (in brief) the reasons for getting these wave forms. Hence draw the wave form of the final output signal Y. Give reasons for your choice. What can we state (in words) as the relation between the final output signal Y and the input signals A and B? The inputs are: A = 1 for 0 to 2 s, 0 for 2 to 3 s, 1 afterwards; B = 1 for 1 to 3 s, 0 otherwise.
Solution.
From the circuit, C1 = Ā·B, C2 = A·B̄ and Y = C1 + C2 = Ā·B + A·B̄ = A·B + Ā·B̄.
C1 = Ā·B is 1 only when A = 0 and B = 1, i.e. between 2 s and 3 s. C2 = A·B̄ is 1 only when A = 1 and B = 0, i.e. from 0 to 1 s and from 3 s onwards.
| Time (s) | A | B | C1 = Ā·B | C2 = A·B̄ | Y = C1 + C2 |
|---|---|---|---|---|---|
| 0 to 1 | 1 | 0 | 0 | 1 | 0 |
| 1 to 2 | 1 | 1 | 0 | 0 | 1 |
| 2 to 3 | 0 | 1 | 1 | 0 | 0 |
| 3 to 4 | 1 | 0 | 0 | 1 | 0 |
| 4 onwards | 1 | 0 | 0 | 1 | 0 |
Y is 1 only between 1 s and 2 s, when A = B = 1. The gate shown is an XNOR gate: the output Y is 1 only if both signals are 0 or both are 1.
Teacher's Note: Y = ĀB + AB̄ inverted gives XNOR: high when inputs are equal.
Exam Note: Find C1 and C2 per interval, then NOR them.
Question 16. Identify which logic gate OR, AND and NOT is represented by the circuits in the dotted line boxes 1, 2 and 3. Give the truth table for the entire circuit for all possible values of A and B.
Solution.
The dotted line box 1 represents a NOT gate. The dotted line box 2 represents an OR gate. The dotted line box 3 represents an AND gate.
The output of box 1 is Ā. The inputs of box 2 are A (after the second NOT) and B̄, so by De Morgan's theorem the output of box 2 is E = A·B̄ = Ā + B.
The inputs of box 3 are E and B, and box 3 is an AND gate, so the output is Y = E·B = (Ā + B)·B = B.
Truth table of the entire circuit:
| A | B | Ā | E = Ā + B | Y = E·B |
|---|---|---|---|---|
| 0 | 0 | 1 | 1 | 0 |
| 0 | 1 | 1 | 1 | 1 |
| 1 | 0 | 0 | 0 | 0 |
| 1 | 1 | 0 | 1 | 1 |
Teacher's Note: Boxes are NOT, OR and AND; overall output equals B.
Exam Note: Find E first, then AND with B.
Free study material for Physics
Xam Idea Solutions for Class 12 Mathematics: Xam Idea Solutions Class 12 Physics Chapter 14 Electronic Devices Long Answer Questions
Complete Math Solutions for Xam Idea Solutions Class 12 Physics Chapter 14 Electronic Devices Long Answer Questions
Review detailed solutions for Class 12 Mathematics. The Xam Idea Solutions Class 12 Physics Chapter 14 Electronic Devices Long Answer Questions PDF provides comprehensive answers mapped to standard Xam Idea Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Detailed Calculation Guides for Class 12
Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.
Complete Your Class 12 Exam Preparation
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the book for Class 12 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.