Step-by-Step Solutions for Class 10 Science Chapter 12 Electricity
Explore reliable textbook solutions for Chapter 12 Electricity tailored for Class 10 learners using methodologies. Utilizing these Science answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.
Download Chapter 12 Electricity Textbook Solutions PDF
View or download the dedicated Chapter 12 Electricity solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Science.
Long Answer Type Questions
Question 1. The potential difference between two points in an electric circuit is 1 volt. What does it mean? Name a device that helps to measure the potential difference across a conductor. (ii) Why does the connecting cord of an electric heater not glow while the heating element does? (iii) Electrical resistivities of some substances at 20° C are given below: Silver 1.60× 10-8 Ω m Copper 1.62 × 10-8 Ω m Tungsten 5.2 x 10-8m Iron 10.0 x 10-82 m Mercury 94.0× 10-8 Ω m Nichrome 100 × 10-6 Ω m Answer the following questions using above data: (a) Among silver and copper, which one is a better conductor? why? (b) Which material would you advise to be used in electrical heating devices and why?
Solution.
(i) The potential difference between two points is 1 volt means that if a charge of 1 coulomb is moved from one point to the other, 1 joule of work is required. The potential difference across a conductor is measured by means of an instrument called the “voltmeter."
(ii) The electric power P is given by P = I2 R The resistance of the heating element is very high. Large amount of heat generates in the heating element and it glows hot. The resistance of connecting cord is very low. Thus, negligible heat generates in the connecting cord and it does not glow.
(iii) (a) Silver is a better conductor due to its lower resistivity.
(b) Nichrome should be used in electrical heating devices due to very high resistivity.
Teacher's Note: One volt means one joule of work per coulomb of charge; a voltmeter measures it.
Exam Note: Define volt and name the device.
Question 2. (a) Name an instrument that measures electric current in a circuit. Define the unit of electric current. (b) What do the following symbols represent in a circuit diagram?
(c) An electric circuit consisting of a 0.5 m long nichrome wire XY, an ammeter, a voltmeter, four cells of 1.5 V each and a plug key was set up. (i) Draw the electric circuit diagram to study the relation between the potential difference maintained between the points X and Y, and the electric current flowing through XY. (ii) The following graph was plotted between V and I values using the above circuit. What would be the values of the V/I ratios when the potential difference is 0.8 V, 1.2 V and 1.6 V respectively? What conclusion do you draw from these values?
Solution.
(a) An instrument that measures electric current in a circuit is called an ammeter. The unit of electric current is the ampere (A). 1 ampere is constituted by the flow of 1 coulomb of charge through any point in an electric circuit in 1 second.
(b) (i) Variable resistance or rheostat. (ii) Plug key or switch (closed).
(c) (i) The circuit diagram is shown below.
(ii) The graph between V and I is a straight line through the origin.
At potential difference 0.8 V, V/I = 0.8/0.3 = 8/3 Ω
At potential difference 1.2 V, V/I = 1.2/0.45 = 8/3 Ω
At potential difference 1.6 V, V/I = 1.6/0.6 = 8/3 Ω
Conclusion: the ratio V/I is constant, so V ∝ I and Ohm's law is obeyed.
Teacher's Note: Ammeter in series and voltmeter across XY; a constant V/I shows Ohm's law is obeyed.
Exam Note: V/I = 8/3 Ω: Ohm's law.
Question 3. Find out the following in the electric circuit given in figure alongside: (a) Effective resistance of two 8 Ω resistors in the combination (b) Current flowing through 4 Ω resistor (c) Potential difference across 4 Ω resistance (d) Power dissipated in 4 Ω resistor (e) Difference in ammeter readings, if any
Solution.
(a) R = (8 × 8)/(8 + 8) = 4 Ω
(b) I = V/R = 8/(4 + 4) = 8/8 = 1 A
(c) V = IR = 1 × 4 = 4 V
(d) P = I2R = 12 × 4 = 4 W
(e) No difference; the same current flows through each element in a series circuit.
Teacher's Note: Two 8 Ω resistors in parallel give 4 Ω, so total resistance is 8 Ω and current is 1 A.
Exam Note: R = 8 Ω, I = 1 A, P = 4 W.
Question 4. Figure shows two electrical circuits.
The batteries in circuit 1 and circuit 2 are identical. (a) Put ticks in the table below to describe the connections of the two resistors P and Q. (b) The resistors P and Q are used as small electrical heaters. State two advantages of connecting them as shown in circuit 2. (c) In circuit 1, the ammeter reads 1.2 A when the switch is closed. Calculate the reading of the voltmeter in this circuit. (d) The two switches in circuit 2 are closed. Calculate the combined resistance of the two resistors in this circuit. (e) When the switches are closed in circuit 2, ammeter 1 reads 5 A and ammeter 2 reads 2 A. Calculate (i) the current in resistor P, (ii) the power supplied to resistor Q, (iii) the energy transformed in resistor Q in 300 s.
Solution.
(a)
| Series | Parallel | |
|---|---|---|
| Circuit 1 | ✓ | |
| Circuit 2 | ✓ |
(b) (i) If one electrical heater stops working due to some defect, the other keeps working normally. (ii) Each heater has its own switch and receives the full battery voltage, so the two can be used independently.
(c) Effective resistance R = 4 + 6 = 10 Ω; current I = 1.2 A; V = IR = 1.2 × 10 = 12 V. Voltmeter reading = 12 V.
(d) Combined resistance RP = (R1R2)/(R1 + R2) = (4 × 6)/(4 + 6) = 24/10 = 2.4 Ω
(e) I = 5 A, I2 = 2 A
(i) The current in resistor P = I1 = I − I2 = 5 A − 2 A = 3 A
(ii) The power supplied to resistor Q = VI = 12 × 2 = 24 W (the identical battery supplies 12 V)
(iii) The energy transformed in resistor Q in 300 s = E = P × t = 24 × 300 = 7200 J
Teacher's Note: In series the resistances add; in parallel each heater gets the full battery voltage and currents add.
Exam Note: V = IR; P = VI; E = Pt.
Free study material for Science
Step-by-Step Xam Idea Solutions for Class 10 Math
Complete Math Solutions for Xam Idea Solutions Class 10 Science Chapter 12 Electricity Long Answer Type Questions
Access the complete chapter-wise PDF for Xam Idea Solutions Class 10 Science Chapter 12 Electricity Long Answer Type Questions. These structured Xam Idea Solutions solutions for Class 10 Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Step-by-Step Mathematical Explanations
Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.
Next Steps in Your Mathematics Revision
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the book for Class 10 Science. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.