Official Pradeep's KL Gogia Textbook Solutions: Class 11 Physics Chapter 22 Work Energy Power And Collision
Review structured textbook solutions for Class 11 Physics Chapter 22 Work Energy Power And Collision prepared by Pradeep's KL Gogia. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Chapter-wise Solutions for Physics: Chapter 22 Work Energy Power And Collision
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Work, Energy, Power and Collision - Part 2 (Problems 57 onwards)
Sample problems based on conservation of energy
Question 57. Two stones each of mass 5 kg fall on a wheel from a height of 10 m. The wheel stirs 2 kg water. The rise in temperature of water would be
(a) 2.6°C (b) 1.2°C (c) 0.32°C (d) 0.12°C
Solution. (d). The potential energy of the two masses is converted into heat and the temperature of the water rises: W = JQ ⇒ 2m × g × h = J(mw S Δt) ⇒ 2 × 5 × 10 × 10 = 4.2(2 × 103 × Δt). ∴ Δt = 1000/(8.4 × 103) = 0.119 °C ≈ 0.12 °C.
Teacher's Note: All gravitational PE of both stones becomes heat; remember to use J = 4.2 J/cal and water mass in grams.
Exam Note: Convert kg to g for calorimetry; use both stones' energy.
Question 58. A boy is sitting on a swing at a maximum height of 5 m above the ground. When the swing passes through the mean position which is 2 m above the ground its velocity is approximately
(a) 7.6 m/s (b) 9.8 m/s (c) 6.26 m/s (d) None of these
(Figure: swing released from A at height h1 = 5 m; mean position B at height h2 = 2 m.)
Solution. (a). By conservation of energy, total energy at A = total energy at B: mgh1 = mgh2 + ½mv2 ⇒ 9.8 × 5 = 9.8 × 2 + v2/2 ⇒ v2 = 58.8 ∴ v = 7.6 m/s.
Teacher's Note: Only the height difference (5 - 2 = 3 m) matters, not the heights from the ground.
Exam Note: Use h = 3 m difference: v = √(2g·3).
Question 59. A block of mass M slides along the sides of a bowl as shown in the figure. The walls of the bowl are frictionless and the base has coefficient of friction 0.2. If the block is released from the top of the side, which is 1.5 m high, where will the block come to rest? Given that the length of the base is 15 m.
(a) 1 m from P (b) Mid point (c) 2 m from P (d) At Q
(Figure: bowl with curved frictionless walls at P and Q, flat base PQ = 15 m, block M released from the top of the wall R at height 1.5 m.)
Solution. (b). Potential energy of block at the starting point = work done against friction in travelling a distance s from point P. ∴ mgh = μmgs ⇒ s = h/μ = 1.5/0.2 = 7.5 m, i.e. the block comes to rest at the mid point between P and Q.
Teacher's Note: Frictionless walls store no loss; all PE is dissipated on the rough base: s = h/μ.
Exam Note: Total path on rough base = h/μ; compare with base length.
Question 60. If we throw a body upwards with velocity of 4 m s-1, at what height its kinetic energy reduces to half of the initial value? Take g = 10 m/s2.
(a) 4 m (b) 2 m (c) 1 m (d) None of these
Solution. (d). Kinetic energy K = ½mv2, so v ∝ √K. When the kinetic energy reduces to half, the velocity becomes v = u/√2 = 4/√2 = 2√2 m/s. From v2 = u2 - 2gh ⇒ (2√2)2 = (4)2 - 2 × 10 × h ∴ h = (16 - 8)/20 = 0.4 m, which is not among the options.
Teacher's Note: Half KE means speed falls by √2, not by half; here h = 0.4 m.
Exam Note: KE half: v = u/√2, then v2 = u2 - 2gh.
Question 61. A 2 kg block is dropped from a height of 0.4 m on a spring of force constant K = 1960 N m-1. The maximum compression of the spring is
(a) 0.1 m (b) 0.2 m (c) 0.3 m (d) 0.4 m
Solution. (a). When a block is dropped from a height, its potential energy is converted into kinetic energy and finally the spring is compressed due to this energy. ∴ Gravitational potential energy of block = elastic potential energy of spring: mgh = ½Kx2 ⇒ x = √(2mgh/K) = √(2 × 2 × 10 × 0.4/1960) = 0.09 m ≈ 0.1 m.
Teacher's Note: Book neglects the extra compression x in the fall height, so the answer is approximate.
Exam Note: Equate mgh to ½Kx2; choose the nearest option.
Question 62. A block of mass 2 kg is released from A on the track that is one quadrant of a circle of radius 1 m. It slides down the track and reaches B with a speed of 4 m s-1 and finally stops at C at a distance of 3 m from B. The work done against the force of friction is
(a) 10 J (b) 20 J (c) 2 J (d) 6 J
(Figure: quadrant track from A down to B, then horizontal surface BC.)
Solution. (b). Block possesses potential energy at A = mgh = 2 × 10 × 1 = 20 J. Finally the block stops at point C, so its total energy goes against friction, i.e. work done against friction is 20 J.
Teacher's Note: Start and end are both at rest, so total friction work equals the initial PE.
Exam Note: Rest at both ends: friction work = mgh; ignore speed at B.
Question 63. A stone projected vertically upwards from the ground reaches a maximum height h. When it is at a height 3h/4, the ratio of its kinetic and potential energies is
(a) 3 : 4 (b) 1 : 3 (c) 4 : 3 (d) 3 : 1
Solution. (b). At the maximum height, total energy = potential energy = mgh. At the height 3h/4, potential energy = mg(3h/4) = 3mgh/4 and kinetic energy = total energy - potential energy = mgh - 3mgh/4 = mgh/4. Hence KE : PE = 1 : 3.
Teacher's Note: Total energy is constant: KE = mgh - PE at any height.
Exam Note: Ratio KE:PE = (h - y):y at height y.
Sample problems based on power
Question 64. A car of mass m is driven with acceleration a along a straight level road against a constant external resistive force R. When the velocity of the car is v, the rate at which the engine of the car is doing work will be [MP PMT/PET 1998; JIMPER 2000]
(a) Rv (b) mav (c) (R + ma)v (d) (ma - R)v
Solution. (c). The engine has to do work against the resistive force R as well as the car is moving with acceleration a. Power = Force × velocity = (R + ma)v.
Teacher's Note: Engine force = resistance + ma; power is that total force times v.
Exam Note: Engine thrust is R + ma, not ma alone.
Question 65. A wind-powered generator converts wind energy into electrical energy. Assume that the generator converts a fixed fraction of the wind energy intercepted by its blades into electrical energy. For wind speed v, the electrical power output will be proportional to
(a) v (b) v2 (c) v3 (d) v4
Solution. (c). Force = v(dm/dt) = v(d/dt)(V×ρ) = vρ(d/dt)[A×l] = vρA(dl/dt) = ρAv2. Power = F × v = ρAv2 × v = ρAv3 ∴ P ∝ v3.
Teacher's Note: Mass flow rate is proportional to v and KE per mass to v2, giving v3.
Exam Note: Wind power ∝ v3; derive via mass flow rate.
Question 66. A pump motor is used to deliver water at a certain rate from a given pipe. To obtain twice as much water from the same pipe in the same time, power of the motor has to be increased to
(a) 16 times (b) 4 times (c) 8 times (d) 2 times
Solution. (d). P = work done/time = mgh/t ∴ P ∝ m, i.e. to obtain twice water from the same pipe in the same time, the power of the motor has to be increased 2 times.
Teacher's Note: Power is proportional to mass lifted per unit time when height is fixed.
Exam Note: P ∝ m for fixed h and t; double mass, double power.
Question 67. A force applied by an engine of a train of mass 2.05 × 106 kg changes its velocity from 5 m/s to 25 m/s in 5 minutes. The power of the engine is [EAMCET 2001]
(a) 1.025 MW (b) 2.05 MW (c) 5 MW (d) 5 MW
Solution. (b). Power = work done/time = increase in kinetic energy/time = ½m(v22 - v12)/t = ½ × 2.05 × 106 × [252 - 52]/(5 × 60) = 2.05 × 106 watt = 2.05 MW.
Teacher's Note: Work-energy theorem gives work; divide by time in seconds (5 min = 300 s).
Exam Note: Convert minutes to seconds; use KE change.
Question 68. From a water fall, water is falling at the rate of 100 kg/s on the blades of turbine. If the height of the fall is 100 m then the power delivered to the turbine is approximately equal to [BHU 1997]
(a) 100 kW (b) 10 kW (c) 1 kW (d) 1000 kW
Solution. (a). Power = work done/t = mgh/t = 100 × 10 × 100 = 105 watt = 100 kW [as m/t = 100 kg/s (given)].
Teacher's Note: Use mass per second directly in mgh/t.
Exam Note: Take g = 10; m/t = 100 kg/s gives 105 W.
Question 69. A particle moves with a velocity v = 5i - 3j + 6k m s-1 under the influence of a constant force F = 10i + 10j + 20k N. The instantaneous power applied to the particle is
(a) 200 J s-1 (b) 40 J s-1 (c) 140 J s-1 (d) 170 J s-1
Solution. (c). P = F·v = (10i + 10j + 20k)·(5i - 3j + 6k) = 50 - 30 + 120 = 140 J s-1.
Teacher's Note: Power is the dot product; the negative j-term reduces the sum.
Exam Note: Dot product term by term; watch the sign of -3.
Question 70. A car of mass 1250 kg experiences a resistance of 750 N when it moves at 30 m s-1. If the engine can develop 30 kW at this speed, the maximum acceleration that the engine can produce is
(a) 0.8 m s-2 (b) 0.2 m s-2 (c) 0.4 m s-1 (d) 0.5 m s-2
Solution. (b). Power = Force × velocity = (Resistive force + Accelerating force) × velocity ⇒ 30 × 103 = (750 + ma) × 30 ⇒ ma = 1000 - 750 ⇒ a = 250/1250 = 0.2 m s-2.
Teacher's Note: Engine force P/v = 1000 N; subtract resistance to get net force.
Exam Note: Net force = P/v - resistance; then divide by mass.
Question 71. A bus weighing 100 quintals moves on a rough road with a constant speed of 72 km/h. The friction of the road is 9% of its weight and that of air is 1% of its weight. What is the power of the engine? Take g = 10 m/s2
(a) 50 kW (b) 100 kW (c) 150 kW (d) 200 kW
Solution. (d). Weight of a bus = mass × g = 100 × 100 kg × 10 m/s2 = 105 N. Total friction force = 10% of weight = 104 N. ∴ Power = Force × velocity = 104 N × 72 km/h = 104 × 20 watt = 2 × 105 watt = 200 kW.
Teacher's Note: Constant speed means engine force equals total resistance; 1 quintal = 100 kg.
Exam Note: Convert 72 km/h to 20 m/s; 1 quintal = 100 kg.
Question 72. Two men with weights in the ratio 5 : 3 run up a staircase in times in the ratio 11 : 9. The ratio of power of first to that of second is
(a) 15/11 (b) 11/15 (c) 11/9 (d) 9/11
Solution. (a). Power P = mgh/t or P ∝ m/t (g and h are constants) ⇒ P1/P2 = (m1/m2)(t2/t1) = (5/3)(9/11) = 45/33 = 15/11.
Teacher's Note: Power rises with weight and falls with time; invert the time ratio.
Exam Note: Invert the time ratio when comparing powers.
Question 73. A dam is situated at a height of 550 metre above sea level and supplies water to a power house which is at a height of 50 metre above sea level. 2000 kg of water passes through the turbines per second. The maximum electrical power output of the power house if the whole system were 80% efficient is
(a) 8 MW (b) 10 MW (c) 12.5 MW (d) 16 MW
Solution. (a). Power = work done/time = mgΔh/t = 2000 × 10 × (550 - 50)/1 = 10 MW. But the system is 80% efficient ∴ power output = 10 × 80% = 8 MW.
Teacher's Note: Head is the height difference (500 m), then apply efficiency to the input power.
Exam Note: Use height difference 500 m, then multiply by 0.8.
Question 74. A constant force F is applied on a body. The power (P) generated is related to the time elapsed (t) as
(a) P ∝ t2 (b) P ∝ t (c) P ∝ t (d) P ∝ t3/2
Solution. (b). F = mdv/dt ∴ F dt = m dv ⇒ v = (F/m)t. Now P = F × v = F × (F/m)t = F2t/m. If force and mass are constants then P ∝ t.
Teacher's Note: Constant force gives v ∝ t, so instantaneous power grows linearly with time.
Exam Note: Constant F: v = Ft/m, so P = F2t/m ∝ t.
Sample problem based on head on elastic collision
Question 75. n small balls each of mass m impinge elastically each second on a surface with velocity u. The force experienced by the surface will be [MP PMT/PET 1998; RPET 2001; BHU 2001; MP PMT 2003]
(a) mnu (b) 2mnu (c) 4mnu (d) ½mnu
Solution. (b). As the ball rebounds with the same velocity, the change in velocity = 2u and the mass colliding with the surface per second = nm. Force experienced by the surface F = m(dv/dt) ∴ F = 2mnu.
Teacher's Note: Elastic rebound reverses velocity, so momentum change per ball is 2mu, not mu.
Exam Note: Elastic rebound: change in momentum = 2mu per ball.
Question 76. A particle of mass m moving with horizontal speed 6 m/sec. If m << M then for one dimensional elastic collision, the speed of lighter particle after collision will be [MP PMT 2003]
(a) 2 m/sec in original direction (b) 2 m/sec opposite to the original direction (c) 4 m/sec opposite to the original direction (d) 4 m/sec in original direction
(Figure: lighter particle m with u1 = 6 m/s and heavy particle M with u2 = 4 m/s, both moving in the same direction.)
Solution. (a). v1 = [(m1 - m2)/(m1 + m2)]u1 + [2m2u2/(m1 + m2)]. Substituting m1 = 0, v1 = -u1 + 2u2 ⇒ v1 = -6 + 2(4) = 2 m/s, i.e. the lighter particle will move in the original direction with the speed of 2 m/s.
Teacher's Note: The heavy body is moving (4 m/s), so the light one is not simply reversed.
Exam Note: Use v1 = -u1 + 2u2 when m << M.
Question 77. A body of mass m moving with velocity v makes a head-on collision with another body of mass 2m which is initially at rest. The loss of kinetic energy of the colliding body (mass m) is [MP PMT 1996; RPET 1999; AIEEE]
(a) 1/2 of its initial kinetic energy (b) 1/9 of its initial kinetic energy (c) 8/9 of its initial kinetic energy (d) 1/4 of its initial kinetic energy
Solution. (c). Loss of kinetic energy of the colliding body ΔK/K = 1 - [(m1 - m2)/(m1 + m2)]2 = 1 - [(m - 2m)/(m + 2m)]2 = 1 - (1/3)2. ΔK = (1 - 1/9)K = (8/9)K. ∴ Loss of kinetic energy is 8/9 of its initial kinetic energy.
Teacher's Note: Speed after impact is u/3, so only 1/9 of KE is retained.
Exam Note: Retained fraction is [(m1-m2)/(m1+m2)]2; loss is its complement.
Question 78. A ball of mass m moving with velocity V, makes a head on elastic collision with a ball of the same mass moving with velocity 2V towards it. Taking direction of V as positive, velocities of the two balls after collision are
(a) -V and 2V (b) 2V and -V (c) V and -2V (d) -2V and V
Solution. (d). Initial velocities of balls are +V and -2V respectively and we know that for the given condition velocities get interchanged after collision. So the velocities of the two balls after collision are -2V and V respectively.
Teacher's Note: Equal masses in elastic head-on collision exchange velocities, signs included.
Exam Note: Equal masses, elastic: swap velocities with their signs.
Question 79. Consider the following statements
Assertion (A): In an elastic collision of two billiard balls, the total kinetic energy is conserved during the short time of collision of the balls (i.e., when they are in contact).
Reason (R): Energy spent against friction does not follow the law of conservation of energy. [AIIMS 2002]
(a) Both A and R are true and the R is a correct explanation of A
(b) Both A and R are true but the R is not a correct explanation of the A
(c) A is true but the R is false
(d) Both A and R are false
Solution. (d). (i) When they are in contact some part of kinetic energy may convert into potential energy so it is not conserved during the short time of collision. (ii) Law of conservation of energy is always true.
Teacher's Note: KE is conserved only before and after an elastic collision; total energy is always conserved.
Exam Note: Total energy always conserved; KE only before and after.
Question 80. A big ball of mass M, moving with velocity u strikes a small ball of mass m, which is at rest. Finally small ball attains velocity u and big ball v. Then what is the value of v [RPET 2001]
(a) (M - m)u/(M + m) (b) mu/(M + m) (c) 2mu/(M + m) (d) Mu/(M + m)
Solution. (a). From the standard equation v1 = [(m1 - m2)/(m1 + m2)]u1 = [(M - m)/(M + m)]u.
Teacher's Note: Target at rest: projectile velocity after collision is (m1-m2)u/(m1+m2).
Exam Note: Learn v1 and v2 formulas for target at rest.
Question 81. A car of mass 400 kg and travelling at 72 kmph crashes into a truck of mass 4000 kg and travelling at 9 kmph, in the same direction. The car bounces back at a speed of 18 kmph. The speed of the truck after the impact is
(a) 9 kmph (b) 18 kmph (c) 27 kmph (d) 36 kmph
Solution. (b). By the law of conservation of linear momentum m1u1 + m2u2 = m1v1 + m2v2 ⇒ 400 × 72 + 4000 × 9 = 400 × (-18) + 4000 × v2 ⇒ v2 = 18 km/h.
Teacher's Note: Bouncing back means a negative v1; km/h units cancel in momentum conservation.
Exam Note: Car's v1 is negative after bouncing back.
Question 82. A smooth sphere of mass M moving with velocity u directly collides elastically with another sphere of mass m at rest. After collision their final velocities are V and v respectively. The value of v is [MP PET 1995]
(a) 2uM/m (b) 2um/M (c) 2u/(1 + m/M) (d) 2u/(1 + M/m)
Solution. (c). Final velocity of the target v2 = [(m2 - m1)/(m1 + m2)]u2 + 2m1u1/(m1 + m2). As initially the target is at rest, substituting u2 = 0 we get v2 = 2Mu/(M + m) = 2u/(1 + m/M).
Teacher's Note: Divide numerator and denominator by M to match the option form.
Exam Note: Target speed 2m1u/(m1+m2); rewrite in options' form.
Question 83. A sphere of mass 0.1 kg is attached to a cord of 1 m length. Starting from the height of its point of suspension this sphere hits a block of same mass at rest on a frictionless table. If the impact is elastic, then the kinetic energy of the block after the collision is
(a) 1 J (b) 10 J (c) 0.1 J (d) 0.5 J
Solution. (a). As the two bodies are of the same mass and the collision is perfectly elastic, their velocities get interchanged, i.e. the block A comes to rest and complete kinetic energy is transferred to block B. Now kinetic energy of block B after collision = kinetic energy of block A before collision = potential energy of block A at the original height = mgh = 0.1 × 10 × 1 = 1 J.
Teacher's Note: Equal masses transfer all KE; the sphere falls through the cord length (1 m).
Exam Note: Equal masses: full KE transfer; KE = mgh.
Question 84. A ball moving horizontally with speed v strikes the bob of a simple pendulum at rest. The mass of the bob is equal to that of the ball. If the collision is elastic the bob will rise to a height
(a) v2/g (b) v2/2g (c) v2/4g (d) v2/8g
Solution. (b). Total kinetic energy of the ball will transfer to the bob of the simple pendulum. Let it rise to height h; by the law of conservation of energy ½mv2 = mgh ∴ h = v2/2g.
Teacher's Note: Equal masses swap velocities, so the bob starts with speed v.
Exam Note: Elastic equal masses: bob gets v; h = v2/2g.
Question 85. A moving body with a mass m1 strikes a stationary body of mass m2. The masses m1 and m2 should be in the ratio m1/m2 so as to decrease the velocity of the first body 1.5 times assuming a perfectly elastic impact. Then the ratio m1/m2 is
(a) 1/25 (b) 1/5 (c) 5 (d) 25
Solution. (c). v1 = [(m1 - m2)/(m1 + m2)]u1 [as u2 = 0 and v1 = u1/1.5 (given)] ⇒ u1/1.5 = [(m1 - m2)/(m1 + m2)]u1 ⇒ m1 + m2 = 1.5(m1 - m2) ⇒ m1/m2 = 5.
Teacher's Note: Set (m1-m2)/(m1+m2) = 2/3 and solve for the ratio.
Exam Note: Velocity reduced 1.5 times means v1 = 2u1/3.
Question 86. Six identical balls are lined in a straight groove made on a horizontal frictionless surface as shown. Two similar balls each moving with a velocity v collide with the row of 6 balls from left. What will happen
(a) One ball from the right rolls out with a speed 2v and the remaining balls will remain at rest
(b) Two balls from the right roll out with speed v each and the remaining balls will remain stationary
(c) All the six balls in the row will roll out with speed v/6 each and the two colliding balls will come to rest
(d) The colliding balls will come to rest and no ball rolls out from right
(Figure: two balls moving right with velocity v toward a row of six touching balls.)
Solution. (b). Only this condition satisfies the law of conservation of linear momentum.
Teacher's Note: Option (a) conserves momentum but not energy; option (b) conserves both.
Exam Note: Check momentum and KE both; only (b) satisfies them.
Question 87. A moving mass of 8 kg collides elastically with a stationary mass of 2 kg. If E be the initial kinetic energy of the mass, the kinetic energy left with it after collision will be
(a) 0.80 E (b) 0.64 E (c) 0.36 E (d) 0.08 E
Solution. (c). Kinetic energy retained by the projectile ΔK/K = [(m1 - m2)/(m1 + m2)]2 ⇒ ΔK = [(8 - 2)/(8 + 2)]2E = (9/25)E = 0.36 E.
Teacher's Note: Retained fraction is the square of (6/10) = 0.6, giving 0.36.
Exam Note: Retained KE = [(m1-m2)/(m1+m2)]2E.
Question 88. A neutron travelling with a velocity v and K.E. E collides perfectly elastically head on with the nucleus of an atom of mass number A at rest. The fraction of total energy retained by neutron is
(a) [(A - 1)/(A + 1)]2 (b) [(A + 1)/(A - 1)]2 (c) [(A - 1)/A]2 (d) [(A + 1)/A]2
Solution. (a). Fraction of kinetic energy retained by the projectile ΔK/K = [(m1 - m2)/(m1 + m2)]2. Mass of neutron (m1) = 1 and mass of atom (m2) = A ∴ ΔK/K = [(1 - A)/(1 + A)]2 or [(A - 1)/(A + 1)]2.
Teacher's Note: Mass numbers act as masses in units of neutron mass; squaring removes the sign.
Exam Note: Neutron mass = 1, nucleus = A; square (1-A)/(1+A).
Question 89. A neutron with 0.6 MeV kinetic energy directly collides with a stationary carbon nucleus (mass number 12). The kinetic energy of carbon nucleus after the collision is
(a) 1.7 MeV (b) 0.17 MeV (c) 17 MeV (d) Zero
Solution. (b). Kinetic energy transferred to the stationary target (carbon nucleus): ΔK/K = 1 - [(m1 - m2)/(m1 + m2)]2 = 1 - [(1 - 12)/(1 + 12)]2 = 1 - 121/169 = 48/169. ∴ ΔK = (48/169) × (0.6 MeV) = 0.17 MeV.
Teacher's Note: Fraction transferred is 4m1m2/(m1+m2)2, about 28% here.
Exam Note: Transferred KE = 4m1m2/(m1+m2)2 of initial.
Question 90. A body of mass m moving along a straight line collides with a body of mass nm which is also moving with a velocity kv in the same direction. If the first body comes to rest after the collision, then the velocity of second body after the collision would be
(a) nv/(1 + nk) (b) nv/(1 - nk) (c) (1 - nk)v/n (d) (1 + nk)v/n
Solution. (d). Initial momentum = mv + nm(kv) and final momentum = 0 + nmV. By the conservation of momentum, mv + nm(kv) = 0 + nmV ⇒ v + nkv = nV ⇒ nV = (1 + nk)v ⇒ V = (1 + nk)v/n.
Teacher's Note: Only momentum conservation is needed; collision type is not specified.
Exam Note: Apply momentum conservation with first body final velocity zero.
Question 91. Which one of the following statement does not hold good when two balls of masses m1 and m2 undergo elastic collision
(a) When m1 < m2 and m2 at rest, there will be maximum transfer of momentum
(b) When m1 > m2 and m2 at rest, after collision the ball of mass m2 moves with four times the velocity of m1
(c) When m1 = m2 and m2 at rest, there will be maximum transfer of kinetic energy
(d) When collision is oblique and m2 at rest with m1 = m2, after collision the balls move in opposite directions
Solution. (b, d). We know that transfer of momentum will be maximum when the target is massive and transfer of kinetic energy will be maximum when target and projectile are having the same mass. It means statements (a) and (c) are correct, but statements (b) and (d) are incorrect because when the target is very light, then after collision it will move with double the velocity of projectile and when collision is oblique and m2 at rest with m1 = m2, after collision the balls move perpendicular to each other.
Teacher's Note: Know the three maximum-transfer conditions: velocity, momentum and kinetic energy.
Exam Note: Equal masses: oblique scattering angle is 90°.
Sample problems based on oblique elastic collision
Question 92. A ball moving with velocity of 9 m/s collides with another similar stationary ball. After the collision both the balls move in directions making an angle of 30° with the initial direction. After the collision their speed will be
(a) 2.6 m/s (b) 5.2 m/s (c) 0.52 m/s (d) 52 m/s
(Figure: ball m with velocity 9 m/s hits stationary ball m; after impact both balls move with speed v at 30° above and below the initial line.)
Solution. (b). Initial horizontal momentum of the system = m × 9. Final horizontal momentum of the system = 2mv cos 30°. According to the law of conservation of momentum, m × 9 = 2mv cos 30° ⇒ v = 5.2 m/s.
Teacher's Note: Vertical components cancel by symmetry; only the horizontal components balance the initial momentum.
Exam Note: Equate 9m to 2mv cos30°.
Question 93. A ball of mass 1 kg, moving with a velocity of 0.4 m/s collides with another stationary ball. After the collision, the first ball moves with a velocity of 0.3 m/s in a direction making an angle of 90° with its initial direction. The momentum of second ball after collision will be (in kg-m/s)
(a) 0.1 (b) 0.3 (c) 0.5 (d) 0.7
Solution. (c). Let the second ball move with momentum P making an angle θ from the horizontal (as shown in the figure). By the conservation of horizontal momentum 1 × 0.4 = P cosθ ......(i). By the conservation of vertical momentum 0.3 = P sinθ ......(ii). From (i) and (ii) we get P = 0.5 kg-m/s.
Teacher's Note: Resolve momentum along and perpendicular to the initial line, then add components as a right triangle.
Exam Note: P = √(0.42 + 0.32) from the two components.
Question 94. Keeping the principle of conservation of momentum in mind which of the following collision diagram is not correct
(Four diagrams (a)-(d): in each, mass M1 moves along the x-axis and strikes M2 at rest; after collision the masses fly off at angles α and β on either side of the x-axis in (a), (b), (c). In (d) M1 goes straight up (perpendicular to x-axis) and M2 goes along the x-axis forward and downward such that the total final momentum is not along the x-axis.)
Solution. (d). In this condition the final resultant momentum makes some angle with the x-axis. Which is not possible because initial momentum is along the x-axis and according to the law of conservation of momentum initial and final momentum should be equal in magnitude and direction both.
Teacher's Note: Momentum is a vector: the y-components after collision must cancel since initially zero.
Exam Note: Final momentum must point along the initial x-axis.
Question 95. Three particles A, B and C of equal mass are moving with the same velocity v along the medians of an equilateral triangle. These particle collide at the centre G of triangle. After collision A becomes stationary, B retraces its path with velocity v then the magnitude and direction of velocity of C will be
(a) v and opposite to B (b) v and in the direction of A (c) v and in the direction of C (d) v and in the direction of B
(Figure: equilateral triangle with A and B at the base corners and C at the apex; each particle moves with speed v toward the centre G.)
Solution. (d). From figure (I) it is clear that before collision the initial momentum of the system = 0. After the collision, A becomes stationary, B retraces its path with velocity v. Let C move with velocity V making an angle θ from the horizontal. As the initial momentum of the system is zero, therefore horizontal and vertical momentum after the collision should also be equal to zero. From figure (II) horizontal momentum: v cosθ + v cos 30° = 0 ......(i); vertical momentum: v sinθ - v sin 30° = 0 ......(ii). By solving (i) and (ii) we get θ = -30° and V = v, i.e. C will move with velocity v in the direction of B.
Teacher's Note: Total momentum stays zero; with A at rest, C must cancel B's momentum exactly.
Exam Note: Initial momentum zero, so final vectors must sum to zero.
Question 96. A ball B1 of mass M moving northwards with velocity v collides elastically with another ball B2 of same mass but moving eastwards with the same velocity v. Which of the following statements will be true
(a) B1 comes to rest but B2 moves with velocity √2v
(b) B1 moves with velocity √2v but B2 comes to rest
(c) Both move with velocity v/√2 in north east direction
(d) B1 moves eastwards and B2 moves northwards
Solution. (d). Horizontal momentum and vertical momentum both should remain conserved before and after collision. This is possible only for the (d) option.
Teacher's Note: Equal masses, elastic: velocity components along the line of impact exchange.
Exam Note: Check both momentum components and kinetic energy.
Sample problems based on inelastic collision
Question 97. A body of mass 40 kg having velocity 4 m/s collides with another body of mass 60 kg having velocity 2 m/s. If the collision is inelastic, then loss in kinetic energy will be [CPMT 1996; UP PMT 1996; Pb. PMT]
(a) 440 J (b) 392 J (c) 48 J (d) 144 J
Solution. (c). Loss of K.E. in inelastic collision ΔK = ½[m1m2/(m1 + m2)](u1 - u2)2 = ½[40 × 60/(40 + 60)](4 - 2)2 = ½ × (2400/100) × 4 = 48 J.
Teacher's Note: This is the maximum loss (bodies move together), computed using relative velocity only.
Exam Note: Loss = ½μ(u1-u2)2 with reduced mass.
Question 98. One sphere collides with another sphere of same mass at rest inelastically. If the value of coefficient of restitution is 1/2, the ratio of their speeds after collision shall be [RPMT 1998]
(a) 1 : 2 (b) 2 : 1 (c) 1 : 3 (d) 3 : 1
Solution. (c). v1/v2 = (1 - e)/(1 + e) = (1 - 1/2)/(1 + 1/2) = (1/2)/(3/2) = 1/3.
Teacher's Note: For equal masses v1 = u(1-e)/2 and v2 = u(1+e)/2.
Exam Note: Equal masses, target at rest: v1:v2 = (1-e):(1+e).
Question 99. The ratio of masses of two balls is 2 : 1 and before collision the ratio of their velocities is 1 : 2 in mutually opposite direction. After collision each ball moves in an opposite direction to its initial direction. If e = 5/6, the ratio of speed of each ball before and after collision would be
(a) (5/6) times (b) Equal (c) Not related (d) Double for the first ball and half for the second ball
Solution. (a). Let masses of the two balls be 2m and m, and their speeds be u and 2u respectively (figure: before collision 2m moves right with u, m moves left with 2u; after collision 2m moves left with v1, m moves right with v2). By conservation of momentum 2mu - 2mu = mv2 - 2mv1 ⇒ v2 = 2v1. Coefficient of restitution = -(v2 - v1)/(u2 - u1) = -(2v1 + v1)/(-2u - u) = 3v1/3u = v1/u = 5/6 [as e = 5/6 given] ⇒ v1/u1 = 5/6 = ratio of the speed of the first ball before and after collision. Similarly for the second ball: v2/u2 = 2v1/2u = v1/u = 5/6.
Teacher's Note: Total momentum is zero here, so the speeds scale by the same factor e.
Exam Note: Zero total momentum: each speed becomes e times its old value.
Question 100. Two identical billiard balls are in contact on a table. A third identical ball strikes them symmetrically and come to rest after impact. The coefficient of restitution is
(a) 2/3 (b) 1/3 (c) 1/6 (d) √3/2
(Figure: ball moving with speed u hits two touching balls; each of the two moves off at 30° to the line of motion with speed v.)
Solution. (a). sinθ = r/2r = 1/2 ⇒ θ = 30°. From conservation of linear momentum mu = 2mv cos 30° or v = u/√3. Now e = relative velocity of separation/relative velocity of approach in the common normal direction. Hence e = v/(u cos 30°) = (u/√3)/(u√3/2) = 2/3.
Teacher's Note: Centre-line geometry gives 30°; restitution acts only along the line joining centres.
Exam Note: Use the common normal direction (30°) for e.
Question 101. A body of mass 3 kg, moving with a speed of 4 m s-1, collides head on with a stationary body of mass 2 kg. Their relative velocity of separation after the collision is 2 m s-1. Then
(a) The coefficient of restitution is 0.5
(b) The impulse of the collision is 7.2 N-s
(c) The loss of kinetic energy due to collision is 3.6 J
(d) The loss of kinetic energy due to collision is 7.2 J
Solution. Corrected: (a), (b) and (d). The book prints (a, b, c), but its own working gives the loss as 7.2 J, which is option (d), not 3.6 J. m1 = 3 kg, m2 = 2 kg, u1 = 4 m/s, u2 = 0. Relative velocity of approach u1 - u2 = 4 m/s; relative velocity of separation v2 - v1 = 2 m/s (given). Coefficient of restitution e = 2/4 = 1/2 = 0.5. Loss in kinetic energy = ½[m1m2/(m1 + m2)](1 - e2)(u1 - u2)2 = ½ × (3 × 2/(3 + 2)) × [1 - (1/2)2] × (4)2 = 7.2 J. Final velocity of m1: v1 = [(m1 - em2)/(m1 + m2)]u1 + [(1 + e)m2/(m1 + m2)]u2 = [(3 - 0.5 × 2)/(3 + 2)] × 4 + 0 = 8/5 m/s. Impulse of collision = change in momentum of m1 = m1v1 - m1u1 = 3 × 8/5 - 3 × 4 = 24/5 - 12 = 4.8 - 12 = -7.2 N-s (magnitude 7.2 N-s). Check: v2 = 3.6 m/s, KE before = 24 J, after = 3.84 + 12.96 = 16.8 J, loss = 7.2 J.
Teacher's Note: Compute v1 and v2 from e, then check KE before and after directly.
Exam Note: Verify KE loss directly: 24 - 16.8 J.
Question 102. Two cars of same mass are moving with same speed v on two different roads inclined at an angle θ with each other, as shown in the figure. At the junction of these roads the two cars collide inelastically and move simultaneously with the same speed. The speed of these cars would be
(a) v cos(θ/2) (b) (v/2)cosθ (c) (v/2)cos(θ/2) (d) 2v cosθ
(Figure: two roads meeting at angle θ and merging into one road; the cars approach the junction along the two roads, each at speed v.)
Solution. (a). Initial horizontal momentum of the system = mv cos(θ/2) + mv cos(θ/2). If after collision cars move with common velocity V then final horizontal momentum of the system = 2mV. By the law of conservation of momentum, 2mV = mv cos(θ/2) + mv cos(θ/2) ⇒ V = v cos(θ/2).
Teacher's Note: Each road makes θ/2 with the common axis; perpendicular components cancel.
Exam Note: Resolve each velocity at θ/2; vertical parts cancel.
Sample problems based on rebound of ball after collision with ground
Question 103. The change of momentum in each ball of mass 60 gm, moving in opposite directions with speeds 4 m/s collide and rebound with the same speed, is
(a) 0.98 kg-m/s (b) 0.73 kg-m/s (c) 0.48 kg-m/s (d) 0.22 kg-m/s
Solution. (c). Momentum before collision = mv, momentum after collision = -mv. ∴ Change in momentum = 2mv = 2 × 60 × 10-3 × 4 = 480 × 10-3 kg-m/s = 0.48 kg-m/s.
Teacher's Note: Rebound at same speed reverses momentum, so the change is twice mv; convert grams to kg.
Exam Note: Change = 2mv; convert 60 g to 0.06 kg.
Question 104. A body falling from a height of 20 m rebounds from hard floor. If it loses 20% energy in the impact, then coefficient of restitution is
(a) 0.89 (b) 0.56 (c) 0.23 (d) 0.18
Solution. (a). It loses 20% energy in impact and only 80% energy remains with the ball. So the ball will rise up to height h2 = 80% of h1 = (80/100) × 20 = 16 m. Now coefficient of restitution e = √(h2/h1) = √(16/20) = √0.8 = 0.89.
Teacher's Note: Energy retained is e2, so e is the square root of the energy fraction.
Exam Note: e = √(energy retained) = √0.8.
Question 105. A rubber ball is dropped from a height of 5 m on a planet where the acceleration due to gravity is not known. On bouncing, it rises to 1.8 m. The ball loses its velocity on bouncing by a factor of [CBSE PMT 1998]
(a) 16/25 (b) 2/5 (c) 3/5 (d) 9/25
Solution. (c). If the ball falls from height h1, then it collides with the ground with speed v1 = √(2gh1) .....(i), and if it rebounds with velocity v2, then it goes up to height h2 from the ground, v2 = √(2gh2) .....(ii). From (i) and (ii): v2/v1 = √(2gh2/2gh1) = √(h2/h1) = √(1.8/5) = √(9/25) = 3/5.
Teacher's Note: Unknown g cancels in the ratio of rebound to impact speed.
Exam Note: g cancels: v2/v1 = √(h2/h1).
Sample problems based on perfectly inelastic collision
Question 106. Which of the following is not a perfectly inelastic collision
(a) Striking of two glass balls (b) A bullet striking a bag of sand (c) An electron captured by a proton (d) A man jumping onto a moving cart
Solution. (a). Corrected explanation: in a perfectly inelastic collision the relative velocity of separation is zero, i.e. the colliding bodies move together with a common velocity (the book's text says "perfectly elastic", which is a misprint). Glass balls bounce apart after striking, so (a) is not perfectly inelastic; in (b), (c) and (d) the bodies stay together.
Teacher's Note: Perfectly inelastic means the bodies stick together (e = 0).
Exam Note: Stick together after impact means perfectly inelastic.
Question 107. A metal ball of mass 2 kg moving with a velocity of 36 km/h has a head-on collision with a stationary ball of mass 3 kg. If after the collision, the two balls move together, the loss in kinetic energy due to collision is [CBSE 1997; AIIMS 2001]
(a) 40 J (b) 60 J (c) 100 J (d) 140 J
Solution. (b). Loss in kinetic energy ΔK = ½[m1m2/(m1 + m2)](u1 - u2)2 = ½ × (2 × 3/(2 + 3)) × (10 - 0)2 = 60 J.
Teacher's Note: 36 km/h = 10 m/s; loss depends only on relative speed and reduced mass.
Exam Note: Convert 36 km/h to 10 m/s first.
Question 108. A mass of 20 kg moving with a speed of 10 m/s collides with another stationary mass of 5 kg. As a result of the collision, the two masses stick together. The kinetic energy of the composite mass will be [MP PMT 2000]
(a) 600 J (b) 800 J (c) 1000 J (d) 1200 J
Solution. (b). By conservation of momentum m1u1 + m2u2 = (m1 + m2)V. Velocity of composite mass V = (20 × 10 + 5 × 0)/(20 + 5) = 8 m/s. ∴ Kinetic energy of composite mass = ½(m1 + m2)V2 = ½(20 + 5) × 82 = 800 J.
Teacher's Note: Find the common velocity first; do not use initial KE (1000 J).
Exam Note: Common velocity from momentum, then KE of combined mass.
Question 109. A neutron having mass of 1.67 × 10-27 kg and moving at 108 m/s collides with a deutron at rest and sticks to it. If the mass of the deutron is 3.34 × 10-27 kg, the speed of the combination is [CBSE PMT 2000]
(a) 2.56 × 103 m/s (b) 2.98 × 105 m/s (c) 3.33 × 107 m/s (d) 5.01 × 109 m/s
Solution. (c). m1 = 1.67 × 10-27 kg, u1 = 108 m/s, m2 = 3.34 × 10-27 kg and u2 = 0. Speed of the combination V = (m1u1 + m2u2)/(m1 + m2) = (1.67 × 10-27 × 108 + 0)/(1.67 × 10-27 + 3.34 × 10-27) = 3.33 × 107 m/s.
Teacher's Note: Deutron is twice the neutron mass, so speed falls to one third.
Exam Note: Mass ratio 1:2 gives V = u/3.
Question 110. A particle of mass m moving eastward with a speed v collides with another particle of the same mass moving northward with the same speed v. The two particles coalesce on collision. The new particle of mass 2m will move in the north-easterly direction with a velocity
(a) v/2 (b) 2v (c) v/√2 (d) v
Solution. (c). Initially both the particles are moving perpendicular to each other with momentum mv. So the net initial momentum = √((mv)2 + (mv)2) = √2 mv. After the inelastic collision both the particles (system) move with velocity V, so linear momentum = 2mV. By the law of conservation of momentum √2 mv = 2mV ∴ V = v/√2.
Teacher's Note: Add perpendicular momenta vectorially, not algebraically.
Exam Note: Perpendicular momenta add as √2 mv.
Question 111. A particle of mass m moving with velocity v collides inelastically with a stationary particle of mass 2m. The speed of the system after collision will be
(a) v/2 (b) 2v (c) v/3 (d) 3v
Solution. (c). By the conservation of momentum mv + 2m × 0 = 3mV ∴ V = v/3.
Teacher's Note: Inelastic here means they move together; only momentum conservation is used.
Exam Note: Total mass 3m shares momentum mv.
Question 112. A ball moving with speed v hits another identical ball at rest. The two balls stick together after collision. If specific heat of the material of the balls is S, the temperature rise resulting from the collision is [Roorkee 1999]
(a) v2/8S (b) v2/4S (c) v2/2S (d) v2/S
Solution. Corrected: (a). The book prints (b), using the whole initial kinetic energy (½mv2 = (2m)SΔt), but only the kinetic energy lost in the collision becomes heat. After sticking, the speed is v/2, so KE lost = ½mv2 - ½(2m)(v/2)2 = ¼mv2. Then ¼mv2 = (2m)SΔt ⇒ Δt = v2/(8S). (Units of work and heat taken consistent, as in the book.)
Teacher's Note: Only the lost KE (a quarter of mv2) heats the balls, since the pair keeps moving.
Exam Note: Heat = KE lost, not initial KE.
Problems based on collision between bullet and block
Question 113. A bullet of mass a is fired with velocity b in a large block of mass c. The final velocity of the system will be
(a) c/(a + c) (b) ab/(a + c) (c) (a + b)/c (d) (a + c)b/a
Solution. (b). Initially the bullet moves with velocity b and after collision the bullet gets embedded in the block and both move together with common velocity. By the conservation of momentum a × b + 0 = (a + c)V ∴ V = ab/(a + c).
Teacher's Note: Embedded bullet means perfectly inelastic; apply momentum conservation with total mass a + c.
Exam Note: Momentum: ab = (a + c)V.
Question 114. A particle of mass 1 g having velocity 3i - 2j has a glued impact with another particle of mass 2 g and velocity as 4j - 6k. Velocity of the formed particle is
(a) 5.6 m s-1 (b) 0 (c) 6.4 m s-1 (d) 4.6 m s-1
Solution. (d). By conservation of momentum m1u1 + m2u2 = (m1 + m2)V. ∴ V = [1(3i - 2j) + 2(4j - 6k)]/(1 + 2) = (3i + 6j - 12k)/3 = i + 2j - 4k. |V| = √((1)2 + (2)2 + (-4)2) = √(1 + 4 + 16) = √21 = 4.6 m s-1.
Teacher's Note: Add momenta as vectors component by component, then take the magnitude.
Exam Note: Vector momentum conservation; magnitude is √21.
Question 115. A body of mass 2 kg is placed on a horizontal frictionless surface. It is connected to one end of a spring whose force constant is 250 N/m. The other end of the spring is joined with the wall. A particle of mass 0.15 kg moving horizontally with speed v sticks to the body after collision. If it compresses the spring by 10 cm, the velocity of the particle is
(a) 3 m/s (b) 5 m/s (c) 10 m/s (d) 15 m/s
Solution. (d). By the conservation of momentum, initial momentum of particle = final momentum of system ⇒ m × v = (m + M)V ∴ velocity of system V = mv/(m + M). Now the spring compresses due to the kinetic energy of the system, so by the conservation of energy ½kx2 = ½(m + M)V2 = ½(m + M)[mv/(m + M)]2 ⇒ kx2 = m2v2/(m + M) ⇒ v = √(kx2(m + M)/m2) = (x/m)√(k(m + M)). Putting m = 0.15 kg, M = 2 kg, k = 250 N/m, x = 0.1 m we get v ≈ 15 m/s (calculated 15.45 m/s, nearest option 15 m/s).
Teacher's Note: Momentum conservation in the collision, then energy conservation during compression.
Exam Note: Two stages: collision (momentum), compression (energy).
Question 116. A bullet of mass m moving with velocity v strikes a block of mass M at rest and gets embedded into it. The kinetic energy of the composite block will be
(a) ½mv2 × m/(m + M) (b) ½mv2 × M/(m + M) (c) ½mv2 × (M + m)/M (d) ½Mv2 × m/(m + M)
Solution. (a). By conservation of momentum, momentum of the bullet (mv) = momentum of the composite block (m + M)V ⇒ velocity of composite block V = mv/(m + M). ∴ Kinetic energy = ½(m + M)V2 = ½(m + M)[mv/(m + M)]2 = ½m2v2/(m + M) = ½mv2[m/(m + M)].
Teacher's Note: Only the fraction m/(m+M) of the bullet's KE survives; the rest is lost as heat.
Exam Note: KE retained = initial KE × m/(m + M).
Question 117. A mass of 10 gm, moving horizontally with a velocity of 100 cm/sec, strikes the bob of a pendulum and strikes to it. The mass of the bob is also 10 gm (see fig.). The maximum height to which the system can be raised is (g = 10 m/sec2)
(a) Zero (b) 5 cm (c) 2.5 cm (d) 1.25 cm
Solution. (d). By the conservation of momentum, momentum of the bullet = momentum of system ⇒ 10 × 1 = (10 + 10) × v ⇒ v = 1/2 m/s. Now maximum height reached by system Hmax = v2/2g = (1/2)2/(2 × 10) m = 1.25 cm.
Teacher's Note: Convert 100 cm/s to 1 m/s; equal masses halve the speed after sticking.
Exam Note: Use SI units: v = 0.5 m/s, h = v2/2g.
Question 118. A bullet of mass m moving with a velocity v strikes a suspended wooden block of mass M as shown in the figure and sticks to it. If the block rises to a height h the initial velocity of the bullet is [MP PMT 1997]
(a) [(m + M)/m]√(2gh) (b) √(2gh) (c) [(M + m)/M]√(2gh) (d) [m/(M + m)]√(2gh)
Solution. (a). By the conservation of momentum mv = (m + M)V and if the system goes up to height h then V = √(2gh). ∴ mv = (m + M)√(2gh) ⇒ v = [(m + M)/m]√(2gh).
Teacher's Note: Two stages: momentum conservation in impact, energy conservation in the swing.
Exam Note: Swing gives V = √(2gh); impact gives v.
Question 119. A bag P (mass M) hangs by a long thread and a bullet (mass m) comes horizontally with velocity v and gets caught in the bag. Then for the combined (bag + bullet) system the
(a) Momentum is mvM/(M + m) (b) Kinetic energy is mV2/2 (c) Momentum is mv(M + m)/M (d) Kinetic energy is m2v2/2(M + m)
Solution. (d). Velocity of combined system V = mv/(m + M). Momentum for combined system = (m + M)V = (m + M)mv/(m + M) = mv. Kinetic energy for combined system = ½(m + M)V2 = ½(m + M)[mv/(m + M)]2 = m2v2/2(m + M).
Teacher's Note: Momentum of the combined system equals the bullet's initial momentum mv.
Exam Note: Momentum conserved; KE = p2/2(m + M).
Question 120. A wooden block of mass M is suspended by a cord and is at rest. A bullet of mass m, moving with a velocity v pierces through the block and comes out with a velocity v/2 in the same direction. If there is no loss in kinetic energy, then up to what height the block will rise
(a) m2v2/2M2g (b) m2v2/8M2g (c) m2v2/4Mg (d) m2v2/2Mg
Solution. (b). By the conservation of momentum, initial momentum = final momentum: mv + M × 0 = m(v/2) + M × V ⇒ V = mv/2M. If the block rises up to height h then h = V2/2g = (mv/2M)2/2g = m2v2/8M2g.
Teacher's Note: Bullet gives up half its momentum; block's speed is mv/2M, then h = V2/2g.
Exam Note: Momentum lost by bullet is gained by block.
Free study material for Physics
Step-by-Step Pradeep's KL Gogia Solutions for Class 11 Math
Download Pradeep's KL Gogia Solutions for Class 11
Explore reliable mathematical solutions for Pradeep's KL Gogia Solutions Physics Chapter 22 Work Energy Power And Collision Part 2 tailored for Class 11 learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.
Detailed Calculation Guides for Class 11
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Explore More Study Resources for Class 11 Math
In addition to these Pradeep's KL Gogia Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the Pradeep's KL Gogia book for Class 11 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.