Evergreen Solutions Class 10 Science Chapter 12 Electricity

Download Class 10 Science Textbook Solutions: Chapter 12 Electricity

Review structured textbook solutions for Class 10 Science Chapter 12 Electricity prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.

Access Textbook Answers and Solutions

Navigate directly to the solved Science textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.

Periodic Test

Question 1. Define resistivity.

Solution. The resistance offered by a conductor of unit length and unit cross section is known as resistivity.

Teacher's Note: Resistivity is a material property; resistance also depends on length and area. Its SI unit is ohm-metre.

Exam Note: Write 'unit length and unit area'; add unit Ω m.

Question 2. Out of the following bulbs rated 40 W, 220 V, 60 W, 220 V and 100 W, 220 V, which one will glow the brightest when connected in series to a supply of 220 V?

Solution. We know that, P = V2/R, so R = V2/P

Now, as all the bulbs are given the same voltage so resistance of the 40 W bulb is the greatest.

As the bulbs are connected in series so the current through the bulbs is the same, and P = I2R.

So the power of the 40 W bulb is the greatest and the power dissipated gives the glow of the bulb. Hence the 40 W bulb glows the brightest.

Teacher's Note: Same current in series, so P = I²R: largest resistance glows brightest. In parallel the 100 W bulb would win.

Exam Note: Mention series gives same current; state 40 W bulb.

Question 3. State the factors that alter the resistance of a conductor. Write the mathematical expression.

Solution. The resistance (R) of a conductor of length l and area of cross section (A) is given by R = ρ(l/A).

With the change in length and area of the conductor the resistance changes. (It also depends on the material, through ρ, and on temperature.)

Teacher's Note: Resistance grows with length, falls with cross-section area, and depends on material and temperature.

Exam Note: Write R = ρl/A and name all four factors.

Question 4. State Joule's law of heating and give its expression.

Solution. According to Joule's law of heating the heat produced in the resistor is

1. Directly proportional to the square of the current through the resistor

2. Directly proportional to the resistance of the given resistor

3. Directly proportional to the time for which the current flows.

Mathematically, Joule's law of heating is given by H = I2Rt

Teacher's Note: Current is squared, so doubling current quadruples heat. All three proportionalities must be stated.

Exam Note: State all three factors; write H = I²Rt with units.

Question 5. Why does the cord of a heating element not glow while the heating element glows?

Solution. The glow of an element is due to the power dissipation of the element. The power of an element is given by P = I2R

As the resistance of the heating element is higher than the cords, the power dissipation of the heating element is greater and it glows.

Teacher's Note: Same current flows through both in series; heat depends on R, and the cord's R is tiny.

Exam Note: Link same current, P = I²R and higher resistance.

Question 6. What is the commercial unit of electrical energy? Convert it into joule. What is the other name of the commercial unit? What is meant by a parallel combination of resistors? Deduce an expression for the equivalent resistance when two resistors are connected in parallel.

Solution. Commercial unit of electrical energy is the unit in which all our household electrical consumptions are measured.

1 kWh = 1000 watt × 3600 seconds = 3.6 × 106 J

The commercial unit of electrical energy is kilowatt hour (kWh). Its other name is the "unit" (BOT unit, Board of Trade unit).

In parallel combination of resistors, the voltage across all the resistors is the same but the total current is divided among the branches.

As the current is given by I = V/R, in the circuit shown below, I = I1 + I2 + I3

V+R3I3 ←R2I2 ←R1I1 ←I →

Resistors R1, R2, R3 in parallel across a cell of potential difference V

V/R = V/R1 + V/R2 + V/R3

1/R = 1/R1 + 1/R2 + 1/R3

Hence, in parallel connection the reciprocal of equivalent resistance is equal to the sum of reciprocals of individual resistances. For two resistors, R = R1R2/(R1 + R2).

Teacher's Note: kWh measures energy, not power. In parallel, V is common and currents add.

Exam Note: Give 1 kWh in joule; derive using I = I₁ + I₂.

Question 7. Two resistors of 5 Ω and 10 Ω are connected in parallel. Eight such sets are connected in series. Find the equivalent resistance of this combination.

Solution. Equivalent resistance of the parallel combination is Rp = (r1 × r2)/(r1 + r2) = (5 × 10)/(5 + 10) = 50/15 = 10/3 Ω

These eight resistances are connected in series, so R = 10/3 + 10/3 + … + 10/3 = 8 × (10/3) = 80/3 Ω

So, the equivalent resistance of the combination is 80/3 Ω (≈ 26.7 Ω).

Teacher's Note: Reduce each parallel pair first, then add identical series sets: eight times 10/3.

Exam Note: Show parallel step, then series sum; final 80/3 Ω.

Question 8. In the circuit shown in figure, calculate (i) the current through the arms AB, AC and CDE, (ii) the potential difference across AB, CD and DE.

6 Ω4 Ω12 ΩCDEAB1.5 V

Circuit for Q.8: the 6 Ω and 4 Ω resistors (arm CDE) are in series; this arm is in parallel with the 12 Ω resistor (arm AB), and a 1.5 V cell is connected to the combination

Solution. The equivalent resistance of the series combination (arm CDE) is Rs = r1 + r2 = 6 + 4 = 10 Ω

The equivalent resistance of the parallel combination, and hence the circuit, is R = (r3 × Rs)/(r3 + Rs) = (12 × 10)/(12 + 10) = 120/22 = 5.45 Ω

If the key in the circuit is closed then only the current will flow. Total current I = 1.5/5.45 = 0.275 A

(i) As the circuit is in parallel combination, the current gets divided into the branches in inverse ratio of the resistances.

Current in the branch AB: IAB = (6 + 4)/(12 + 6 + 4) × 0.275 = (10/22) × 0.275 = 0.125 A

The current in the arm CDE (the same as in AC, as they are in series) IAC = 12/(12 + 4 + 6) × 0.275 = (12/22) × 0.275 = 0.15 A

(ii) As the circuit is in parallel connection the potential difference across AB and CE are the same: VAB = 1.5 V

Now the potential difference across CD and DE is proportional to the resistances, so VCD = 6/(6 + 4) × 1.5 = 0.9 V

And VDE = 4/(6 + 4) × 1.5 = 0.6 V

Teacher's Note: Series arm shares one current; parallel arms share one voltage. Divide current inversely to resistance.

Exam Note: Write R, total I, branch currents, then voltage divider; give units.

Question 9. Find the equivalent resistance of the following combination of resistors:

6 Ω12 Ω4 Ω3 Ω5 ΩCell (internal resistance 12 Ω)

Combination of resistors for Q.9

Solution. Answer: The points are marked as shown.

6 Ω12 Ω4 Ω3 Ω5 ΩCell (internal resistance 12 Ω)ABCDEF

Same circuit with the points A, B, C, D, E and F marked

The resistance across AB is RAB = 4 + (12 × 4)/(12 + 4) = 4 + 4 = 8 Ω. (Here the 6 Ω and 12 Ω resistors are in parallel; their combination 6 × 12/(6 + 12) = 4 Ω is in series with the 4 Ω resistor.)

The resistance across CD is (3 + 5) Ω: RCD = 3 + 5 = 8 Ω

The resistance across EF is REF = (RAB × RCD)/(RAB + RCD) = (8 × 8)/(8 + 8) = 4 Ω

Now, the internal resistance of the cell (12 Ω) is in series with REF

Req = 4 + 12 = 16 Ω

Teacher's Note: Reduce stepwise: parallel 6 and 12 first, then series, then the two branches in parallel, then the cell's 12 Ω.

Exam Note: Show each reduction step; final 16 Ω including internal resistance.

Question 10. (a) Express Ohm's law by a mathematical formula. (b) Draw a circuit diagram to verify Ohm's law. (c) Present the relationship between the voltage applied across a conductor and the current flowing through it graphically.

Solution. (a) Mathematically, Ohm's law is given by V = IR, where V is the potential difference, I is the current and R is the resistance.

(b) The circuit diagram to verify Ohm's law is shown below (B - battery, Rh - rheostat, K - key, A - ammeter, V - voltmeter, R - resistance).

Rh (rheostat)K (key)A−+B (battery)R (resistance)V+−

Circuit to verify Ohm's law: battery, rheostat, key and ammeter in series with resistance R; voltmeter connected across R

This circuit diagram explains Ohm's Law.

(c) The potential difference across a conductor is proportional to the current through the resistor. V ∝ I, so V = IR.

This is similar to the equation of a straight line passing through the origin. So the graph between voltage and current is a straight line through the origin (a V–I graph has slope R; the I–V graph shown below has slope 1/R).

Voltage V (volts)Current I (amperes)OVIslope = 1/R

Graph of I against V for a conductor obeying Ohm's law: a straight line through the origin

Teacher's Note: Vary current with the rheostat, note V and I; V/I stays constant. Voltmeter is in parallel with R.

Exam Note: Draw ammeter in series, voltmeter parallel, plot straight line through origin.

Comprehensive Exercises (MCQ)

Question 1. No current flows between two charged bodies when connected, if they have the same:
A. capacity
B. quantity of charge
C. charge to potential ratio
D. potential

Solution. Correct option: D. According to Ohm's Law current only flows when there is a potential difference; if the potential difference is zero then no current will flow.

Teacher's Note: Charge flows only due to a potential difference, like water needing a level difference.

Exam Note: Answer: same potential means zero current; do not pick charge.

Question 2. If a wire of resistance R is melted and recast to half of its length, then new resistance of the wire will be:
A. R/4
B. R/2
C. R
D. 2R

Solution. Correct option: A. As the volume of the wire remains same, A1l1 = A2l2

A1l = A2(l/2), so A2 = 2A1

R1 = R = ρ(l/A1)

R2 = ρ(l/2)/(2A1) = (1/4) × ρ(l/A1) = R1/4 = R/4

Teacher's Note: Volume is constant: halving length doubles area, so resistance becomes one-fourth.

Exam Note: Use constant volume; write R' = R/4 with steps.

Question 3. An equal resistor are first connected in series and then connected in parallel. The ratio of the maximum to the minimum resistance is:
A. n
B. 1/n
C. n2
D. 1/n2

Solution. Correct option: C. The maximum resistance is obtained in case of series combination (Rs) and the minimum resistance is obtained in case of parallel combination (Rp). If the resistance of each wire is R, then Rs = n × R and Rp = R/n

Therefore, Rs/Rp = nR/(R/n) = n2

Teacher's Note: Series gives nR, parallel gives R/n; dividing gives n squared. Check with n = 2.

Exam Note: Show both formulas, then ratio n².

Question 4. If R1 and R2 are the resistances of filaments of a 400 W and a 200 W lamp, designed to operate on the same voltage, then:
A. R1 = 2R2
B. R2 = 2R1
C. R2 = 4R1
D. R1 = R2

Solution. Correct option: B. We know that, P = V2/R, so R = V2/P

Hence, R1/R2 = P2/P1 = 200/400

R2 = 2R1

Teacher's Note: At fixed voltage resistance is inversely proportional to power; the lower-power lamp has higher resistance.

Exam Note: Use R = V²/P; ratio inverts power ratio.

Question 5. In a circuit containing two unequal resistors connected in parallel:
A. the current is same in both the resistors.
B. the current is large in the larger resistance.
C. the voltage is same across both the resistors.
D. the voltage drop is larger across the larger resistance.

Solution. Correct option: C. In parallel connection the voltage is equal in the branches.

Teacher's Note: Parallel branches share the same two nodes, so voltage is equal; the current divides.

Exam Note: State 'same voltage, different currents' for parallel.

Question 6. The equivalent resistance in series combination is:
A. smaller than the largest resistance.
B. larger than the largest resistance
C. smaller than the smallest resistance
D. larger than the smallest resistance.

Solution. Correct option: B. As the equivalent resistance in series connection is the sum of the individual resistances, so it is greater than the largest resistance.

Teacher's Note: Series resistances add, so the total exceeds every single one. Option D is true but not the best choice.

Exam Note: Pick the strongest statement: larger than the largest.

Question 7. A house is fitted with 5 tubes each of 40 W. If all the tubes are lighted for 20 hours and if the cost of electrical unit is Rs. 0.50, the total cost of electricity consumed is:
A. Rs. 20
B. Rs. 4
C. Rs. 5
D. Rs. 2

Solution. Correct option: D. The electrical power of a single tube in kilowatt = 40/1000 = 0.040 kW

The electrical power of 5 tubes in kilowatt = 0.2 kW

Total unit of energy consumed = 0.2 × 20 = 4 kWh = 4 units

The cost of electricity consumed = 4 × 0.50 = Rs. 2

Teacher's Note: Convert watts to kilowatts, multiply by hours to get units, then by rate per unit.

Exam Note: Show kW × h = units, then units × rate.

Question 8. Of the two bulbs in a house, one glows brighter than the other. Which of the two has a larger resistance?
A. the dim bulb
B. the brighter bulb
C. both have the same resistance
D. becomes four times

Solution. Correct option: A. The brightness of a bulb is representation of the power dissipated by the bulb. The power is given by P = V2/R

Household bulbs are in parallel at the same voltage, so the dimmer bulb (smaller P) has the larger resistance.

Teacher's Note: Household bulbs get the same voltage, so lower power means higher resistance. In series it reverses.

Exam Note: Quote P = V²/R at same voltage.

Question 9. You are given a resistance wire of length 50 cm and a battery of negligible resistance. In which of the following cases is the largest amount of heat generated:
A. when only half of the wire is connected to the battery.
B. when the wire is divided into four equal parts and all the four parts are connected in parallel.
C. when the wire is divided into two equal parts and both the parts are connected in parallel.
D. when the wire is connected to the battery directly.

Solution. Correct option: B. Heat generated in an element is given by H = (V2/R)t

For largest amount of heat generation, R must be smallest and R is smallest in parallel connection of four equal parts: Req = (R/4)/4 = R/16.

Teacher's Note: Battery voltage is fixed, so heat is V²t/R: choose the smallest equivalent resistance.

Exam Note: Use H = V²t/R; compare R, R/2, R/4, R/16.

Question 10. You are given three bulbs of 25 W, 40 W and 60 W marked at 220 V. Which one of them has lowest resistance?
A. 60 W bulb
B. 40 W bulb
C. 25 W bulb
D. no conclusion can be drawn

Solution. Correct option: A. The power of a bulb is given by P = V2/R

Hence, the resistance will be minimum if the power is maximum. So, the 60 W bulb will have the lowest resistance (the 25 W bulb has the largest).

Teacher's Note: Same rated voltage means R = V²/P; highest wattage gives lowest resistance. Don't reverse it.

Exam Note: Write R = V²/P; 60 W gives least resistance.

Question 11. The potential difference across a conductor is doubled, the rate of generation of heat will:
A. become one-fourth
B. be halved
C. be doubled
D. become four times

Solution. Correct option: D. Heat generated is given by H = (V2/R)t, so H ∝ V2

Hence, with doubling of the potential difference, the heat produced will be four times.

Teacher's Note: For fixed resistance, heat rate depends on V squared, so doubling V gives four times.

Exam Note: Quote H ∝ V² and substitute 2V.

Question 12. What are the essential requirements of a heater filament?
A. high resistivity, low melting point
B. low resistivity, low melting point
C. high resistivity, high melting point
D. low resistivity, high melting point.

Solution. Correct option: C. According to Joule's law of heating, H = I2Rt

So, greater the resistance (i.e. greater resistivity), greater the heat produced.

To bear the amount of heat produced, the melting point of the element must be high.

Teacher's Note: A heater needs high resistance for heat and high melting point to avoid melting. Nichrome fits both.

Exam Note: Give both reasons; name nichrome as example.

Question 13. Two wires of the same metal have the same length, but cross-sections are in the ratio 3:1. They are joined in series. The resistance of the thicker wire is 10 Ω. The total resistance of the combination will be:
A. 40 Ω
B. 40/3 Ω
C. 5/2 Ω
D. 100 Ω.

Solution. Correct option: A. As the length of the wires are the same so the resistances will depend only upon the cross-sectional area. R = ρl/A, so R ∝ 1/A

So, R1/R2 = A2/A1 = 1/3

R2 = 3R1 = 3 × 10 = 30 Ω

So, the resistance of the combination = R1 + R2 = 10 + 30 = 40 Ω

Teacher's Note: Thicker wire has lower resistance: the thinner one is three times larger, 30 Ω, then add.

Exam Note: Identify thicker wire first; add in series.

Question 14. You are given three equal resistors. The number of resistances which can be obtained by joining them in series and in parallel grouping is:
A. two
B. three
C. four
D. six

Solution. Correct option: C. The numbers of combinations are:

1. All three in parallel (R/3)

2. All three in series (3R)

3. Two in parallel and one in series (3R/2)

4. Two in series and one in parallel (2R/3)

Hence four different resistances can be obtained.

Teacher's Note: List systematically: all series, all parallel, and the two mixed arrangements with their values.

Exam Note: List all four with values; avoid missing a mixed one.

Comprehensive Exercises (T/F)

Question 1. Write true or false for the following statement: The unit of measurement of charge is coulomb.

Solution. True.

Charge is measured in coulomb.

Teacher's Note: One coulomb is the charge carried by a current of one ampere in one second.

Exam Note: Write unit C; link with I = Q/t.

Question 2. Write true or false for the following statement: A metal has a very large number of free electrons and a non-metal very less number of free electrons.

Solution. True.

Teacher's Note: Free electrons make metals good conductors; non-metals hold electrons tightly.

Exam Note: One-line reason: free electrons decide conduction.

Question 3. Write true or false for the following statement: An electron in a metal is free to move anywhere but cannot leave the metal.

Solution. True.

Due to attraction of the atoms, the free electrons cannot leave the metal.

Teacher's Note: Electrons move within the metal but the lattice attraction keeps them from escaping at normal conditions.

Exam Note: Add the reason: attraction of the metal atoms.

Question 4. Write true or false for the following statement: Potential and potential difference are vector quantities.

Solution. False.

Potential and potential difference are scalar quantities.

Teacher's Note: They have magnitude and sign but no direction; electric field is the vector.

Exam Note: Write 'scalar' and contrast with field.

Question 5. Write true or false for the following statement: Potential is positive of positively charged body and is negative of a negatively charged body.

Solution. True.

As potential depends on the charge of a body, potential is positive of positively charged body and is negative of a negatively charged body.

Teacher's Note: The sign of potential follows the sign of charge on the body.

Exam Note: State sign follows charge.

Question 6. Write true or false for the following statement: Positive charges flow from high potential to low potential.

Solution. True.

Teacher's Note: Conventional current direction is from high to low potential, opposite to electron flow.

Exam Note: Mention conventional current direction.

Question 7. Write true or false for the following statement: Battery is a source of maintaining a constant potential difference across two ends of a conductor.

Solution. True.

Teacher's Note: A cell uses chemical energy to maintain the potential difference that drives current.

Exam Note: Name chemical energy as the source.

Question 8. Write true or false for the following statement: The units of resistance are ampere.

Solution. False.

The unit of resistance is ohm (Ω).

Teacher's Note: Ampere is the unit of current; resistance is measured in ohm, where 1 Ω = 1 V/A.

Exam Note: Correct to ohm (Ω); give 1 Ω = 1 V/A.

Question 9. Write true or false for the following statement: If the resistance of a conductor is doubled, the current is halved.

Solution. True.

This is in accordance with Ohm's law (I = V/R, at constant V).

Teacher's Note: At constant voltage, current is inversely proportional to resistance.

Exam Note: Say 'at constant V' while applying I = V/R.

Question 10. Write true or false for the following statement: Resistance of a conductor increases with the increase in temperature.

Solution. True.

With increase in temperature the random motion of the atoms and electrons in a conductor increases, so collisions increase and the resistance increases.

Teacher's Note: Hotter metal ions vibrate more, scattering electrons more often, so resistance rises.

Exam Note: Give the reason: more collisions at higher temperature.

Question 11. Write true or false for the following statement: Insulator like wood and rubber has a very low electrical resistance.

Solution. False.

Insulator like wood and rubber has a very high electrical resistance.

Teacher's Note: Insulators lack free electrons, so their resistance is very high.

Exam Note: Correct to 'very high'; give free-electron reason.

Question 12. Write true or false for the following statement: If resistors are connected in series, the current through each resistor remains the same.

Solution. True.

In series connection the current through each resistance is the same.

Teacher's Note: Series has one path, so the same current flows through every element.

Exam Note: Pair with: voltage divides in series.

Question 13. Write true or false for the following statement: If resistors are connected in parallel, the voltage across each remains the same.

Solution. True.

In parallel connection the voltage across each resistance is the same.

Teacher's Note: Parallel branches connect the same two points, so they share one potential difference.

Exam Note: Pair with: current divides in parallel.

Question 14. Write true or false for the following statement: Resistance of a piece of rubber is more than that of a piece of copper.

Solution. True.

Because rubber is an insulator while copper is a conductor.

Teacher's Note: Rubber has almost no free electrons; copper has many, so its resistivity is tiny.

Exam Note: Compare insulator and conductor in one line.

Question 15. Write true or false for the following statement: Electric power of a circuit is the rate at which work is done in maintaining the electric current in the circuit.

Solution. True.

Teacher's Note: Power is energy transferred per second; P = VI, unit watt.

Exam Note: Write P = W/t = VI.

Question 16. Write true or false for the following statement: 1 kWh = 3.6 × 106 joule

Solution. True.

1 kWh = 1000 W × 3600 s = 3.6 × 106 J.

Teacher's Note: Convert kilowatt to watt and hour to seconds, then multiply.

Exam Note: Show 1000 × 3600 for full marks.

Question 17. Write true or false for the following statement: Electric power is also called BOTU.

Solution. False.

BOTU (Board of Trade Unit) measures electrical energy, not power.

Teacher's Note: BOT unit is another name for kWh, an energy unit; power is in watt.

Exam Note: Say BOTU = kWh, energy.

Question 18. Write true or false for the following statement: Heat dissipated by a conductor when a current is passed through it is directly proportional to the resistance of the conductor.

Solution. True.

According to Joule's law of heating, H = I2Rt (at constant current and time).

Teacher's Note: Heat is proportional to R only when current and time are fixed.

Exam Note: Add 'for constant I and t'.

Question 19. Write true or false for the following statement: Electric bulb works on heating effect of current.

Solution. True.

Teacher's Note: The filament heats up to incandescence because of Joule heating.

Exam Note: Link filament, heating effect and glow.

Question 20. Write true or false for the following statement: The electrical appliance having higher power draws a larger current.

Solution. True.

Power is given by P = VI, so at the same voltage I = P/V is larger for larger P.

Teacher's Note: At the same supply voltage, current is directly proportional to power rating.

Exam Note: Use I = P/V at fixed voltage.

Question 21. Write true or false for the following statement: The quantity of charge flowing past a point multiplied by time is current.

Solution. False.

Current is the amount of charge flowing per unit time: I = Q/t.

Teacher's Note: Current is charge divided by time, not multiplied.

Exam Note: Write I = Q/t clearly.

Question 22. Write true or false for the following statement: The flow of charge through a conducting wire connected to a cell is the result of chemical reaction inside the cell.

Solution. True.

Teacher's Note: Chemical reaction in the cell maintains the potential difference that drives the charge.

Exam Note: Mention the cell converts chemical to electrical energy.

Question 23. Write true or false for the following statement: The resistivity of all pure metals increases with increase in temperature.

Solution. True.

With increase in temperature the random motion of the atoms and electrons in a conductor increases, so collisions increase and the resistivity increases.

Teacher's Note: Pure metals have positive temperature coefficient; alloys change very little.

Exam Note: Add alloy contrast: nearly constant resistivity.

Question 24. Write true or false for the following statement: Ohm's law is a relation between the power used in a circuit to the current and the potential difference.

Solution. False.

According to Ohm's law, V = IR, a relation between potential difference, current and resistance (not power).

Teacher's Note: Ohm's law links V, I and R at constant temperature; power is P = VI.

Exam Note: State V = IR and the constant temperature condition.

Question 25. Write true or false for the following statement: A series circuit has only one conducting path for the electrons that move through it; a parallel circuit has multiple conducting paths.

Solution. True.

As in parallel connection there are multiple branches, so there are multiple conducting paths.

Teacher's Note: Series has one loop; parallel branches give several paths, so one failure does not stop all.

Exam Note: Mention household wiring is parallel.

Question 26. Write true or false for the following statement: A conducting wire offers resistance to the flow of electrons because electrons repel each other in the wire.

Solution. False.

A conducting wire offers resistance to the flow of electrons due to the random collision between the electrons and the stationary atoms (ions) of the wire.

Teacher's Note: Resistance comes from electrons colliding with lattice ions, not from mutual repulsion.

Exam Note: Give collision with ions as the cause.

Step-by-Step Evergreen Solutions for Class 10 Math

Complete Math Solutions for Evergreen Solutions Class 10 Science Chapter 12 Electricity

Explore reliable mathematical solutions for Evergreen Solutions Class 10 Science Chapter 12 Electricity tailored for Class 10 learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.

Step-by-Step Mathematical Explanations

Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.

Next Steps in Your Mathematics Revision

Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.

FAQs

What are these [current-page:node:field_author] Solutions for Class 10 Science?

They are chapter-wise solved questions from the book for Class 10 Science. Each answer is explained step by step so you can check your work and revise.

Are the [current-page:node:field_author] Class 10 Science Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these [current-page:node:field_author] solutions for Class 10 Science?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising [current-page:node:field_author] Class 10 Science questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these Class 10 Science Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.