All In One Solutions Class 10 Science Chapter 12 Electricity

Step-by-Step Solutions for Class 10 Science Chapter 12 Electricity

Review structured textbook solutions for Class 10 Science Chapter 12 Electricity prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.

Download Chapter 12 Electricity Textbook Solutions PDF

Navigate directly to the solved Science textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.

Check Point 01

Question 1. If a body has positive charge, then what does it mean?

Solution.

If a body has positive charge it means that it has less no. of electrons than the no. of protons. Due to this imbalance of the charges, the body will attract the negative charged body.

Teacher's Note: A body becomes positively charged when it loses electrons, leaving more protons than electrons.

Exam Note: Positive charge means electron deficiency; it attracts negative charge.

Question 2. In which direction does current flow in an electric circuit?

Solution.

In an electrical circuit the current flows from the positive to the negative. The conventional current always flows in the direction opposite to the direction of flow of the electron.

Teacher's Note: By convention, current flows from the positive to the negative terminal outside the cell, opposite to electron flow.

Exam Note: Conventional current is opposite to electron flow.

Question 3. The charge on an electron is 1.6 × 10-19C. Find the number of electrons that will flow per second to constitute a current of 2A.

Solution.

We know that;

Q = ne

Where,

n is an integral multiple can take values 1, 2, 3….

e⁻ is the charge on the electron.

And, \( I = \dfrac{Q}{t} \)

\( \therefore I = \dfrac{ne}{t} \)

Thus, \( n = \dfrac{I \times t}{e} \)

\( n = \dfrac{2 \times 1}{1.6 \times 10^{-19}} \)

\( \therefore n = 1.25 \times 10^{19} \)

Teacher's Note: Charge is quantised: total charge equals number of electrons times electron charge, and current is charge per second.

Exam Note: Use Q = ne and I = Q/t.

Question 4. Write a low resistance device name which is always connected in series with the device through which the current is to be measured.

Solution.

Ammeter is a device that is connected in series so as to measure the current through the circuit. It has a very low resistance so that maximum current passes through it and thus the correct amount of current through the circuit can be measured.

Teacher's Note: An ammeter measures current and has very low resistance, so it is connected in series without changing the current.

Exam Note: Ammeter: low resistance, connected in series.

Question 5. If work done in moving a charge of 20 mC from infinity to a point O in an electric field is 15 J, then what is the electric potential at this point?

Solution.

We know that work done in moving a charge Q in a potential V is given by:

\( W = Q \times V \)

\( \therefore V = \dfrac{W}{Q} \)

\( V = \dfrac{15\,\text{J}}{20 \times 10^{-3}\,\text{C}} \)

Since, Q = 20 mC = 20 × 10⁻³ C

\( V = 7.5 \times 10^{2}\ \text{V} \)

Teacher's Note: Electric potential is work done per unit charge in bringing a charge from infinity; its unit is volt.

Exam Note: V = W/Q; convert mC to C.

Question 6. Write a high resistance device name which is always connected in parallel.

Solution.

Voltmeter is a high resistive device that is used to measure the voltage across a component. It is always connected in parallel to the component whose voltage is to be measured. It is highly resistive so that the current cannot pass through it and thus the current will pass through the component connected in parallel to it so as to measure the accurate voltage drop across the component.

Teacher's Note: A voltmeter has very high resistance and is connected in parallel across a component to measure its potential difference.

Exam Note: Voltmeter: high resistance, connected in parallel.

Check Point 02

Question 1. What does it mean a circuit is closed or open?

Solution.

If a circuit is closed that means electrons can easily flow through the circuit and thus electric current will flow through it.

If a circuit is open that means the electrons will not be able to flow through the circuit which means that there will be no current flowing through it.

Teacher's Note: A closed circuit forms a complete conducting path so current flows; an open circuit has a break, so no current.

Exam Note: Closed: current flows; open: no current.

Question 2. A student made an electric circuit as shown below

V+−A+−R₁R₂+−

Is there any mistake in this circuit? If any then correct it.

Solution.

Here, in this circuit, the student has kept the ammeter in parallel and the voltmeter in series with the circuit.

But actually, the ammeter should always be connected in series as it has a very low resistance so when we connect the ammeter in series, maximum current will pass through it and thus the correct amount of current through the circuit can be measured.

In the same way, the voltmeter should always be connected in parallel as it is highly resistive due to which the current cannot pass through it and thus the current will pass through the component connected in parallel to it so as to measure the accurate voltage drop across the component.

A+−V+−R₁R₂+−

Teacher's Note: Ammeter must be in series because of low resistance; voltmeter must be in parallel because of high resistance.

Exam Note: Ammeter in series, voltmeter in parallel.

Question 3. Define the electric resistance of a wire and also write its SI unit.

Solution.

Electric resistance (R) is defined as the ratio of the voltage applied (V) to the current (I) flowing through the circuit.

It is given by the formula:

\( R = \dfrac{V}{I} \)

Its SI unit is known as ohm (Ω).

Teacher's Note: Resistance is the opposition a conductor offers to current flow; it equals potential difference divided by current.

Exam Note: R = V/I; unit ohm (Ω).

Question 4. Keeping the potential difference constant, the resistance of a circuit is halved. Then, how much does the current changes?

Solution.

We know that by Ohm’s Law:

V = I × R

\( \therefore I = \dfrac{V}{R} \)

Now,

New resistance R′ = R/2

\( \therefore I' = \dfrac{V}{R/2} = 2\dfrac{V}{R} \)

We know that: \( \dfrac{V}{R} = I \)

∴ I′ = 2I

Thus, from this we can conclude that if the resistance of the circuit is halved then the current gets doubled.

Teacher's Note: At constant voltage, current is inversely proportional to resistance, so halving resistance doubles the current.

Exam Note: Constant V: halve R, current doubles.

Question 5. What is the difference between a good conductor and a poor conductor? Give two example of each.

Solution.

Good ConductorPoor Conductor
1. It allows the electricity to pass through it easily.1. It doesn’t allow the electricity to pass through it.
2. It has less resistivity towards the flow of current.2. It has more resistivity towards the flow of current.
3. Example: Iron, Graphite3. Example: Wood, Plastic

Teacher's Note: Good conductors allow current easily because of low resistivity; poor conductors resist current because of high resistivity.

Exam Note: Good: low resistivity (iron, graphite); poor: high (wood, plastic).

Question 6. The potential difference across wire is 75V and its electric resistance is 30Ω. Find out the electric current through the wire.

Solution.

We know that by Ohm’s Law:

V = I × R

\( \therefore I = \dfrac{V}{R} \)

Here: V = 75 V

And, R = 30 Ω

\( I = \dfrac{75\,\text{V}}{30\,\Omega} \)

∴ I = 2.5 A

Teacher's Note: Ohm's law states that potential difference across a conductor is proportional to current, giving I = V/R.

Exam Note: I = V/R = 75/30 = 2.5 A.

Question 7. If the length of a wire is halved and its cross-sectional area is doubled, then what would be the resistance of the wire?

(Given, initially the resistance of the wire is R)

Solution.

The formula of resistance is:

\( R = \dfrac{\rho \times l}{A} \)

Where,

ρ = resistivity

l = Length of the conductor

A = Area of the conductor

If length of the conductor is halved then, \( l_1 = \dfrac{l}{2} \)

And, the cross sectional area is doubled, A₁ = 2A

\( \therefore R_1 = \dfrac{\rho \times l_1}{A_1} \)

\( R_1 = \dfrac{\rho \times \frac{l}{2}}{2A} \)

\( R_1 = \dfrac{1}{4} \times \dfrac{\rho \times l}{A} \)

Now, \( \dfrac{\rho \times l}{A} = R \)

\( \therefore R_1 = \dfrac{R}{4} \)

Thus, we can conclude that the new resistance of the wire when the area of wire is doubled and length is halved becomes 1/4th of the initial resistance.

Teacher's Note: Resistance is directly proportional to length and inversely proportional to cross-sectional area, R = ρl/A.

Exam Note: R ∝ l/A: half length, double area gives R/4.

Length of the conductor

Question 8. Define the electric resistivity of material and also write its SI unit.

Solution.

Resistivity: It is defined as the resistance offered by a conductor having unit length and unit cross-sectional area. It is denoted by ρ (rho).

\( \rho = \dfrac{R \times A}{l} \)

The SI unit of resistivity ρ is Ωm.

Teacher's Note: Resistivity is a property of the material, equal to resistance of a wire of unit length and unit area.

Exam Note: ρ = RA/l; SI unit ohm-metre (Ωm).

Check Point 03

Question 1. In which type of combination of different resistors will have equal value of electric current through them?

Solution.

When different resistors are connected in series combination the current passing through them remains the same.

V = V₁ + V₂ + V₃ + … + Vₙ

Since, V = IR

Putting the value in the above equation.

I Req = I(R₁ + R₂ + R₃ + … + Rₙ)

Req = R₁ + R₂ + R₃ + … + Rₙ

Thus, we can say that the current remains constant in series connection.

Teacher's Note: In a series combination the same current flows through every resistor, and the total resistance is their sum.

Exam Note: Series: same current; Req = R1 + R2 + R3.

Question 2. IF different resistors have the same value of electric potential across them, in which way they are connected to each other?

Solution.

When different resistors are connected in parallel combination the voltage drop remains the same.

Teacher's Note: In a parallel combination every resistor has the same potential difference across it, while the current divides.

Exam Note: Parallel: same voltage across each resistor.

Question 3. Why, we do not use series combination of connecting electric appliances in household circuit?

Solution.

We do not use series combination for connecting electrical appliances in household circuit because if there is a fault in one of the appliances which leads to a break in the circuit, the other appliances connected in the series will also stop working.

Thus, Parallel combination is used for connecting electrical appliance in the household circuit.

Teacher's Note: In series, one faulty appliance breaks the whole circuit and each appliance gets less voltage; household circuits use parallel wiring.

Exam Note: Household wiring is parallel: independent appliances, same voltage.

Question 4. What do you understand by a mixed combination of resistances?

Solution.

A Mixed combination of resistances means when two or more resistances are connected in series and parallel simultaneously.

These types of combinations are known as Mixed combination.

RRRRVR+

Teacher's Note: A mixed combination has some resistors in series and others in parallel in the same circuit.

Exam Note: Mixed: reduce the parallel groups first, then add series.

Question 5. In the circuit shown below, calculate the net resistance of the circuit.

10 Ω15 Ω20 Ω5 Ω45 V

Solution.

Here, the resistances 10Ω and 15Ω are connected in series and also the resistances 20Ω and 5Ω are also connected in series.

Thus, R₁ = 10Ω + 15Ω = 25Ω

R₂ = 20Ω + 5Ω = 25Ω

Now, these two resistances R₁ and R₂ are connected in parallel

\( \therefore \dfrac{1}{R} = \dfrac{1}{R_1} + \dfrac{1}{R_2} \)

\( R = \dfrac{R_1 \times R_2}{R_1 + R_2} \)

\( R = \dfrac{25 \times 25}{25 + 25}\,\Omega = \dfrac{625}{50}\,\Omega \)

R = 12.5 Ω

Thus the net resistance is 12.5Ω.

Teacher's Note: Add resistors in each series branch first, then combine the two equal branches in parallel.

Exam Note: Series first, then parallel: 25 Ω ∥ 25 Ω = 12.5 Ω

Check Point 04

Question 1. What is the heating effect of electric current?

Solution.

When current flows through a conductor, it produces some amount of heat. This phenomenon is known as the heating effect of electric current.

The heat (H) produced during the heating effect of electric current is given by the formula:

Heat, H = I²Rt

Where, I = Current

R = Resistance of conductor

t = time

The SI unit of the heat produced is Joules (J).

Teacher's Note: Current passing through a resistor converts electrical energy into heat; heat produced equals I squared times R times t.

Exam Note: H = I²Rt, measured in joules.

Question 2. State the factors on which the heat produced in a current conductor depends. Give one practical application of this effect.

Solution.

The factors on which heating effect in a current conductor depends are:

a) The time for which the current is flowing through the circuit. Greater the time greater will be the heating effect.

b) Resistance of the conductor. More resistance yields more heating effect.

c) The amount of current flowing through the circuit.

Application: This principle of heating effect of current carrying conductor is used in the iron.

Teacher's Note: Heat depends on current, resistance and time (H = I²Rt); heaters and electric irons use this effect.

Exam Note: Heat depends on I², R and t.

Question 3. A fuse wire consists of an alloy of lead and tin. Why?

Solution.

The fuse wire is made up of lead and tin alloy as this alloy has a very low melting point and a very high resistivity. When a large amount of current flows through this alloy, due to the high resistivity heat is produced due to the flow of high current which makes the alloy melt (as it has a very low melting point). Thus, as alloy melts the circuit breaks and the appliances connected to it are saved from any damage due to the high amount of current flowing in the circuit.

Teacher's Note: A fuse wire melts when excessive current flows, breaking the circuit and protecting appliances; lead-tin alloy melts easily.

Exam Note: Fuse: low melting point, connected in series, protects appliances.

Question 4. An electric heater of resistance 500Ω is connected to a mains supply for 30 min. If 15A current flows through the filament of the heater, then calculate the heat energy produced in the heater.

Solution.

We know that the formula of heat is given by:

Heat, H = I²Rt

Where;

t = 30 min = 30×60 sec = 1800 sec

I = 15 A

R = 500 Ω

∴ H = (15)² × 500 × 1800 J

H = 225 × 500 × 1800 J

∴ H = 20.25 × 10⁷ J

Thus Total heat produced by the heater is 20.25 × 10⁷ J in 30 min due to flow of 15 A current.

Teacher's Note: Heat produced in a resistor is I²Rt; convert time to seconds before substituting to get joules.

Exam Note: Convert minutes to seconds; H = I²Rt.

Question 5. Why are electric bulbs filled with chemically inactive nitrogen and argon?

Solution.

The electric bulbs are filled with chemically inactive gases such as nitrogen or argon.

When current is passed through the bulb, the bulb filament made of tungsten glows due to its high resistivity. If it were exposed to air, the very hot tungsten would react with oxygen (oxidise) and burn out, so the filament would break and the circuit would open.

Thus for the long life of the bulb the electric bulb is filled with chemically inactive nitrogen and argon.

Teacher's Note: Inert gases prevent the very hot tungsten filament from reacting with oxygen, so it lasts longer.

Exam Note: Inert gas prevents filament oxidation, increasing bulb life.

Question 6. What is the maximum power in kilowatts of the appliance that can be connected safely to a 13A, 230V mains socket?

Solution.

We know that the formula of power is:

P = VI

Here;

V = 230 V

I = 13 A

P = 230 × 13 W

∴ P = 2990 W

or, P = 2.99 kW

Thus, the maximum power of 2.99 kW can be drawn from the circuit.

Teacher's Note: Power drawn equals voltage times current, so the socket rating limits the maximum safe appliance power.

Exam Note: P = VI = 230 × 13 = 2990 W.

Question 7. Power of a lamp is 60 W. Find the energy in joules consumed by it in 1s.

Solution.

We know that the power can be stated as the amount of electric energy consumed per unit time.

\( \text{Power}, P = \dfrac{\text{Energy consumed}, E}{\text{Time}, t} \)

On solving for Energy, we get

Energy, E = P × t

Here;

P = 60 W

t = 1 s

E = 60 W × 1 s

∴ E = 60 J

Thus, the energy in joules is 60 J.

Teacher's Note: Energy consumed equals power multiplied by time; one watt means one joule per second.

Exam Note: E = P × t = 60 × 1 = 60 J.

Chapter Exercise

Question 1. Electric fuse is an important component of all domestic circuits. Why?

Solution.

Electric fuse is used as a safety device. Whenever, there is a large amount of current flowing through a circuit due to some faults, due to the lower melting point of the alloy, the fuse melts down which breaks the circuit connection.

Thus, electric fuse is an important component of all domestic circuits.

Teacher's Note: A fuse is a safety device connected in series; it melts when current is too high and breaks the circuit.

Exam Note: Fuse protects appliances from overload and short circuit.

Question 2. State the law which governs the amount of heat produced in a metallic conductor when current is passed through it for a given time. Express this law mathematically.

Solution.

When current flows through a conductor for a given time, it produces some amount of heat. This phenomenon is known as the heating effect of electric current (Joule’s law of heating).

The heat (H) produced during the heating effect of electric current is given by the formula:

H = I²Rt

Here, I = Current

R = Resistance of conductor

t = time

The SI unit of the heat produced is Joules (J).

Teacher's Note: Joule's law says heat produced in a conductor is proportional to square of current, resistance and time.

Exam Note: Joule's law: H = I²Rt.

Question 3. Name two common materials, used as heating elements.

Solution.

The two common materials, used as heating element are:

i. Tungsten wire.

ii. Nichrome wire (It is made of 80% of nickel and 20% of chromium).

Teacher's Note: Heating elements need high resistivity and high melting point; nichrome and tungsten both satisfy this.

Exam Note: Heating elements: nichrome, tungsten; high resistivity, high melting point.

Question 4. Relate 1 kWh and SI unit of energy.

Solution.

1 kWh = 1000 watt × 3600 seconds

= 3.6 × 10⁶ watt second

= 3.6 × 10⁶ joule (J)

The SI unit of energy is joules (J).

Thus, we conclude that 1 kWh is 3.6 × 10⁶ J

Teacher's Note: The kilowatt-hour is the commercial unit of electrical energy: energy used by a 1 kW appliance in one hour.

Exam Note: 1 kWh = 3.6 × 10⁶ J.

Question 5. You are given three bulbs of 40 W, 60 W and 100W. Which of them has lower resistance?

Solution.

We know that the formula of power is given by:

\( P = \dfrac{V^2}{R} \)

So, from this equation we can see that power is inversely proportional to the resistance R (for the same voltage), which means that lower is the resistance, more will be the power.

Thus we can say that: 100W will have the lower resistance.

Teacher's Note: At the same voltage, power is inversely proportional to resistance, so the highest wattage bulb has the least resistance.

Exam Note: Same voltage: P = V²/R, so higher power means lower resistance.

Question 6. Mention two special features of the material used as an element of an electric iron.

Solution.

Two features of the material used as an element of an electric iron are:

a) It should have a high melting point.

b) It should have a very high resistance.

Teacher's Note: A heating element must have high resistivity to produce heat and a high melting point so it does not melt.

Exam Note: Element: high melting point and high resistivity (not low).

Question 7. Write the advantages of connecting electrical appliances in parallel and disadvantages of connecting them in series in a household circuit.

Solution.

Parallel Connection: The electrical appliances should always be connected in parallel combination because if there is any fault/damage in any of the appliances then in series combination the whole circuit will get open but in parallel combination only that part containing the damaged appliance is open which will have no effect on the working of other appliances in the circuit.

CellBulbBulb

Series Connection: We do not use series combination for connecting electrical appliances in household circuit as whenever there will be a damage/breakage in the circuit of any one appliance of the household then, due to the series connection all other connections will also break.

Teacher's Note: In parallel wiring each appliance works independently at full voltage; in series, one fault switches off all.

Exam Note: Parallel: independent appliances; series: one break stops all.

Question 8. Derive the relation between kilowatt hour and joule.

Solution.

1 kWh = 1000 watt × 3600 seconds

= 3.6 × 10⁶ watt second

= 3.6 × 10⁶ joule (J)

The SI unit of energy is joules (J).

Teacher's Note: One kWh is the energy of 1000 W working for 3600 s, which converts directly to joules.

Exam Note: 1 kWh = 3.6 × 10⁶ J.

Question 9. What kind of graph is obtained by plotting values of V and I? Why?

Solution.

The graph obtained by plotting the values of V and I is a linear graph. We will observe that as the voltage V increases the value of current I also increases linearly.

This happens because we know that according to the Ohm’s Law:

V ∝ I

∴ V = IR

Ohm's lawCurrentVolt

Teacher's Note: Ohm's law makes V proportional to I, so the V-I graph is a straight line through the origin.

Exam Note: V-I graph is a straight line through the origin.

Question 10. It is possible to replace resistors joined in series by an equivalent single resistor of resistance. How?

Solution.

Yes, it is possible to replace resistors joined in series by an equivalent single resistor.

Example: Suppose there are three resistors of 1Ω, 2Ω and 3Ω connected in series.

So, if we want to attach only one resistor instead of these three resistors then we add these resistors i.e.

1Ω + 2Ω + 3Ω = 6Ω

Thus, we can place a single equivalent resistance of 6Ω instead of these three resistors.

Teacher's Note: Resistors in series carry the same current, so their equivalent resistance is simply the sum of individual resistances.

Exam Note: Series: Req = R1 + R2 + R3.

Question 11. Aluminium wire has radius 0.25 mm and length of 75 m. If the resistance of the wire is 10Ω, calculate the resistivity of aluminium.

Solution.

The formula of resistance is:

\( R = \dfrac{\rho \times l}{A} \)

Where,

ρ = resistivity

l = Length of the conductor

A = Area of the conductor

\( \therefore \rho = \dfrac{R \times A}{l} \)

Here:

R = 10 Ω

r = 0.25 mm

l = 75 m

We know that the area of the wire will be:

A = πr²

∴ A = 3.14 × (0.25 × 10⁻³)² m²

A = 0.196 × 10⁻⁶ m²

Putting the given values in the above formula,

\( \rho = \dfrac{10 \times 0.196 \times 10^{-6}}{75} \)

\( \rho = 2.61 \times 10^{-8}\ \Omega\text{m} \)

Teacher's Note: Resistivity follows from R = ρl/A; the wire's area comes from the radius, with millimetres converted to metres.

Exam Note: ρ = RA/l; convert mm to m.

Question 12. You are given three resistors each of 3Ω and you are asked to get all possible values of resistance when you connect them in different combinations. How many values of resistance can you get?

Solution.

Here: R₁ = 3Ω

R₂ = 3Ω

R₃ = 3Ω

Parallel combination:

R₁, R₂ and R₃ connected in stair like pattern one above the other.

\( \dfrac{1}{R_{eq}} = \dfrac{1}{R_1} + \dfrac{1}{R_2} + \dfrac{1}{R_3} \)

\( \dfrac{1}{R_{eq}} = \dfrac{1}{3} + \dfrac{1}{3} + \dfrac{1}{3} \)

\( \dfrac{1}{R_{eq}} = \dfrac{3}{3} \)

\( R_{eq} = \dfrac{3}{3}\,\Omega \)

Req = 1Ω

Series Combination:

R₁, R₂ and R₃ connected in same line across the potential difference V

Req = R₁ + R₂ + R₃

Req = 3 + 3 + 3

Req = 9Ω

Mixed combination:

R₁ is connected in series with the parallel combination of R₂ and R₃.

\( \dfrac{1}{R_p} = \dfrac{1}{R_2} + \dfrac{1}{R_3} \)

Putting the values of the resistance, we get

Thus, we get \( R_p = 1.5\,\Omega \)

Rs = R₁ + Rp = 3 + 1.5 = 4.5Ω

Another mixed combination: R₁ and R₂ are connected in series and this combination is connected in parallel with R₃.

Rs = R₁ + R₂ = 3 + 3 = 6Ω

\( \dfrac{1}{R} = \dfrac{1}{6} + \dfrac{1}{3} = \dfrac{3}{6} = \dfrac{1}{2} \)

R = 2Ω

Thus, using all three resistors, four different values of resistance can be obtained: 1Ω, 9Ω, 4.5Ω and 2Ω.

Teacher's Note: Three equal resistors can be joined in four ways using all of them, giving 9, 1, 4.5 and 2 ohm.

Exam Note: Use series, parallel and both: 9, 1, 4.5, 2 Ω.

Question 13. Find the current drawn from the battery by network of four resistors shown in the figure?

10 Ω10 Ω10 Ω10 Ω+−3 VK

Solution.

Given:

V = 3 V

R₁ = R₂ = R₃ = R₄ = 10Ω

Here, R₁ and R₂ are connected in series

And, R₃ and R₄ are connected in series.

\( \therefore \dfrac{1}{R_{eq}} = \dfrac{1}{R_1 + R_2} + \dfrac{1}{R_3 + R_4} \)

\( \dfrac{1}{R_{eq}} = \dfrac{1}{10 + 10} + \dfrac{1}{10 + 10} = \dfrac{1}{20} + \dfrac{1}{20} = \dfrac{2}{20} \)

\( R_{eq} = \dfrac{20}{2} = 10\,\Omega \)

Now, by Ohm’s Law

V = I × R

\( I = \dfrac{V}{R} = \dfrac{3}{10} \)

∴ I = 0.3 A

Thus, Current drawn by the resistors from the battery is 0.3 A

Teacher's Note: Two resistors in series on each side of the diamond form two 20 ohm branches in parallel, giving 10 ohm.

Exam Note: Reduce series first, then parallel; I = V/Req = 0.3 A.

Question 14. A wire is cut into three equal parts and then connected in parallel with the same source. How will its

(i) resistance and resistivity gets affected?

(ii) How would the total current and the current through the parts change?

Solution.

i. Here, the new resistance of each part: R′ = R/3

\( \dfrac{1}{R_{eq}} = \dfrac{1}{R_1} + \dfrac{1}{R_2} + \dfrac{1}{R_3} \)

\( \dfrac{1}{R_{eq}} = \dfrac{1}{R/3} + \dfrac{1}{R/3} + \dfrac{1}{R/3} \)

\( \dfrac{1}{R_{eq}} = \dfrac{3}{R} + \dfrac{3}{R} + \dfrac{3}{R} \)

\( \dfrac{1}{R_{eq}} = \dfrac{9}{R} \)

\( R_{eq} = \dfrac{R}{9} \)

The resistivity is dependent on the nature of the material.

Hence, there will be no change in the resistivity of the wire.

ii. Now, by Ohm’s Law

V = I × R

\( I' = \dfrac{V}{R_{eq}} = \dfrac{V}{R/9} = \dfrac{9V}{R} \)

∴ I′ = 9I

Thus, the total current will increase 9 times than the previous current.

The current through each part is V/(R/3) = 3V/R = 3I, i.e. 3 times the previous current.

Teacher's Note: Cutting into three equal parts makes each R/3; three in parallel give R/9. Resistivity depends only on the material.

Exam Note: Parallel of three R/3 parts gives R/9; resistivity unchanged.

Question 15. How will you conclude that the same potential difference (voltage) exists across three resistors connected in a parallel arrangement to a battery?

Solution.

Suppose 3 resistances are R₁, R₂ and R₃. We will connect these resistances in parallel with an ammeter (A), a voltmeter (V), a plug key (K) and a battery of known voltage as shown in figure given below.

We will close the key K and record the ammeter and voltmeter readings.

R₁R₂R₃XYV+−A−+II+−K

Now we will open the key and switch the position of voltmeter and ammeter as shown in the figure given below.

A+−V+−YXR₁R₂R₃

We will close the switch and note the readings. Similarly, we will switch the position of voltmeter to resistances R₂ and R₃ and observe the readings.

We will find that readings of ammeter keep on changing but readings of voltmeter in all cases remain almost the same.

Teacher's Note: Resistors in parallel share the same two end points, so a voltmeter across any one reads the same potential difference.

Exam Note: Parallel: same voltage across every resistor, currents differ.

Question 16. What will be the length of a nichrome wire resistance 5.0Ω, if the length of similar wire of 120 cm has resistance of 2.5 Ω? Why?

Solution.

Here,

l₂ = 120 cm = 1.20 m

R₁ = 5.0Ω

R₂ = 2.5Ω

Now,

\( R_1 = \dfrac{\rho \times l_1}{A} \)

And

\( R_2 = \dfrac{\rho \times l_2}{A} \)

(Here, resistivity ρ and the area A remain same as the wires are similar.)

\( \therefore \dfrac{R_1}{R_2} = \dfrac{\rho \times l_1 / A}{\rho \times l_2 / A} \)

\( \dfrac{R_1}{R_2} = \dfrac{l_1}{l_2} = \dfrac{l_1}{120 \times 10^{-2}} \)

Now,

\( \dfrac{5.0}{2.5} = \dfrac{l_1}{120 \times 10^{-2}} \)

l₁ = 2 × 120 × 10⁻² m

l₁ = 24 × 10⁻¹ m

∴ l₁ = 240 cm

Teacher's Note: For wires of the same material and area, resistance is directly proportional to length, so double resistance means double length.

Exam Note: Same material, same area: R1/R2 = l1/l2.

Question 17. Disha was given two thin wires A and B in science laboratory. The teacher asked her to find out which wire was “fuse wire” and which one was “nichrome wire”. Disha was given batteries of 3 V and 12 V and some connecting wires. The teachers also advised her to switch off fan while performing the activities and take necessary precautions to avoid burns. Disha performed the activities for testing and concluded that wire A is nichrome wire, whereas wire B is fuse wire.

On the basis of above information, answer the following questions

(i) Describe the activity which Disha performed to conclude that wire A is nichrome wire.

(ii) Describe the activity which Disha performed to conclude that wire B is fuse wire.

Solution.

i) Disha connected wire A with both the batteries.

When wire A was connected with 3 V battery, Disha found that the wire started heating. When the wire A was connected with 12 V battery, she found that the wire is emitting a large amount of heat.

Thus, she concluded that wire A is a nichrome wire as nichrome wire has a very large resistance and it produces a large amount of heat.

ii) Disha connected wire B with both the batteries.

When wire B was connected with 3 V battery, she did not find anything.

When the wire B was connected with 12 V battery, she found that the wire has started melting.

Thus, she concluded that wire B is a fuse wire as fuse wire has a very low melting point and it melts as a large amount of current is made to pass through it.

Teacher's Note: Nichrome has high resistivity and a high melting point so it heats up; a fuse wire melts at low temperature.

Exam Note: Nichrome glows without melting; fuse wire melts quickly.

Challengers

Question 1. Three different circuits (I, II and III) are constructed using identical batteries and resistors of R and 2R ohm. What can be said about current I in arm AB of each circuit.

ER2RR2RR2RRABIER2RR2RR2RR2RR2RR2RRABIIER2RR2RR2RR2RR2RR2RR2RR2RRABIII

A. I<sub>I</sub> &gt; I<sub>II</sub> &gt; I<sub>III</sub>

B. I<sub>I</sub> &lt; I<sub>II</sub> &lt; I<sub>III</sub>

C. I<sub>II</sub> &lt; I<sub>I</sub> &lt; I<sub>III</sub>

D. I<sub>I</sub> = I<sub>II</sub> = I<sub>III</sub>

Solution.

The equivalent resistance in all the three circuits comes out to be the same so II = III = IIII. The reason being, the two end resistors of R and R ohms add up to 2R and then the two resistors of 2R in parallel are equivalent to a single resistor of R ohms and then the process repeats until the arm AB is reached, so, finally the equivalent resistance of all the circuits is the same.

Hence, option D is correct.

Teacher's Note: In an R-2R ladder each stage reduces to R, so every circuit has equal resistance and equal battery current.

Exam Note: Ladder repeats: equivalent resistance same, so currents equal.

Question 2. Two cells of 3V each are connected in parallel. An external resistance of 0.5 Ω is connected in series to the junction of two parallel resistors of 4 Ω and 2Ω and then to common terminal of battery through each resistor as shown in figure. What is the current flowing through 4Ω resistor?

3 V3 V0.5 Ω4 Ω2 Ω

A. 0.25 A

B. 0.55 A

C. 0.35 A

D. 1.50 A

Solution.

The given circuit can be reduced to:

3 V11/6 Ω18/11 A

The equivalent resistance can be calculated as:

3 V3 V0.5 Ω4 Ω2 Ω18/11 A

\( R_{eq} = \dfrac{4 \times 2}{4 + 2} + 0.5 = \dfrac{11}{6}\,\Omega \)

The net current in the circuit is given as

\( I = \dfrac{V}{R} = \dfrac{3}{11/6} = \dfrac{18}{11}\ \text{A} \)

so, Inet = 18/11 A.

The circuit can be drawn as shown above.

The voltage drop across the parallel resistance combination is \( \dfrac{18}{11} \times \dfrac{4}{3} = \dfrac{24}{11}\,\text{V} \), so net current in the 4 Ω resistor is \( \dfrac{24/11}{4} = \dfrac{6}{11} \) = 0.55 A.

Hence, option B is correct.

Teacher's Note: Find total current from equivalent resistance, then use the voltage across the parallel pair to get the 4 ohm current.

Exam Note: Req = 11/6 Ω; I = 18/11 A; I₄ = 6/11 A.

Question 3. The current flowing through a wire of resistance 2 Ω varies with time as shown in figure alongside. The amount of heat produced (in J) in 3 s would be

−3−2−11230ABCDEFGHIJt (s)I (A)

A. 2 J

B. 18 J

C. 28 J

D. 10 J

Solution.

Assuming that each interval is of 1 second, we can calculate the heat for each interval and just sum it up to find the net heat produced,

Heat, H = I²Rt

Where,

I is the current,

R is the resistance,

t is the time taken

For AD,

I = 3 A, R = 2 Ω, t = 1 sec

Putting the values in the above formula, we get

H_AD = 3² × 2 × 1 = 18 J

For DG,

I = −2 A, R = 2 Ω, t = 1 sec

Putting the values in the above formula, we get

H_DG = (−2)² × 2 × 1 = 8 J

For GJ,

I = 1 A, R = 2 Ω, t = 1 sec

Putting the values in the above equation, we get

H_GJ = 1² × 2 × 1 = 2 J

So Total amount of heat generated in 3 sec

H_NET = 18 + 8 + 2 = 28 J

Hence, option C is correct.

Teacher's Note: Heat in each interval is I²Rt; squaring makes the negative current give positive heat, so add all intervals.

Exam Note: Heat uses I², so negative current still heats.

Question 4. In the movie Tango and Cash, Kurt Russell and Sylvester Stallone escape from a prison by jumping off the top of a tall wall through the air and onto a high voltage power line. Before the jump, Stallone objects to the idea; Russell responds with “You did not take high school Physics. Did you? As long as you are only touching one wire. And your feet are not touching the ground, you do not get electrocuted.” Is this a correct statement?

Solution.

The statement is correct.

Explanation: The statement is true since the motion of charges through a material requires a high potential and a low potential, that is, a potential difference. Since their feet are not touching the ground, the electric charges are not able to flow through their body.

Thus we conclude that the electric charges require a potential difference to flow across a material. This is the reason why birds sitting on the high tension line are not electrocuted.

Teacher's Note: Current flows only across a potential difference; touching one wire with no path to ground gives none.

Exam Note: Charge flows only with potential difference; birds on wires are safe.

Question 5. Two wire A and B with circular cross-sections having identical lengths and are made of the same material. Yet, wire A has four times the resistance of wire B. How many times greater is the diameter of wire B than wire A?

Solution.

If wire A has four times the resistance, then it must have the smaller cross-sectional area since resistance and cross-sectional area are inversely proportional. In fact, A must have one-fourth the cross-sectional area of B. Since the cross-sectional area of a circular cross-section is given by the expression:

\( A = \pi \times r^2 \)

Wire A must have one-half the radius of wire B and therefore one-half the diameter. Put another way, the diameter of wire B is two times greater than the diameter of wire A.

Teacher's Note: With equal length and material, resistance is inversely proportional to area, which depends on the square of the diameter.

Exam Note: R ∝ 1/d²: four times R means half diameter.

Question 6. Calculate the equivalent resistance of the network across the points A and B shown in figure.

DEFCAB4 Ω4 Ω8 Ω8 Ω

Solution.

Here in this diagram, say:

R₁ = 4Ω

R₂ = 8Ω

R₃ = 4Ω

R₄ = 8Ω

When we want to find the resistance across points A and B then resistances R₁ and R₂ are connected in series and resistances R₃ and R₄ are also connected in series. Thus,

R₅ = R₁ + R₂ = 4Ω + 8Ω = 12Ω

And, R₆ = R₃ + R₄ = 4Ω + 8Ω = 12Ω

Now, this R₅ and R₆ are connected to each other in parallel. Thus the equivalent resistance R_AB across points A and B is:

\( \dfrac{1}{R_{AB}} = \dfrac{1}{R_5} + \dfrac{1}{R_6} \)

\( \dfrac{1}{R_{AB}} = \dfrac{1}{12} + \dfrac{1}{12} \)

\( \dfrac{1}{R_{AB}} = \dfrac{2}{12} = \dfrac{1}{6} \)

\( \therefore R_{AB} = 6\,\Omega \)

Teacher's Note: Two 12 ohm paths between the terminals, each formed by series resistors, are joined in parallel to give 6 ohm.

Exam Note: Series 4+8 = 12 Ω; two in parallel give 6 Ω.

Question 7. The amount of energy transferred when 10C of charge passes through a potential difference of 20 V is the same as the energy needed to raise a 2kg mass through a distance x. Find the value of x, take the value of g as 10 m/s2

Solution.

Given:

Mass of the object = 2 kg,

Charge = 10 C,

Potential difference = 20 V,

Calculations:

We know that the energy transferred when a charge q is moved through a potential difference V is given by

E = q · V

Where,

q is the charge,

V is the potential difference

Also gravitational potential energy stored in an object is given as:

E = m × g × h

Where,

m is the mass of the object,

g is gravitational acceleration,

h is the height through which it is raised,

As per the problem both are equal,

m·g·x = q·V

Putting the values in the equation, we get

2 × 10 × x = 10 × 20

\( x = \dfrac{200}{20} \)

x = 10 meters.

Teacher's Note: Electrical energy equals charge times potential difference; equate it to gravitational potential energy mgx to find height.

Exam Note: qV = mgx, so x = 200/20 = 10 m.

Question 8. The diagram shows a cell connected in series with an ammeter and three resistors (10 Ω, 20Ω, 30Ω). The circuit can be completed by a movable contact M. When M is connected to x, then ammeter reads 0.6 A. What is the ammeter reading when M is connected to y?

AXYZM10 Ω20 Ω30 Ω+−

Solution.

The current when it is connected to x is 0.6 A, so net resistance is 10 ohms so the cell voltage is 10 × 0.6 = 6 V.

Now when M is connected to y

The net resistance is the sum of the resistances of 10 Ω and 20 Ω

Rnet = 10 + 20 = 30 Ω

As we know by Ohm’s law,

V = I R

Putting the values in the equation, we get

6 V = I × 30 Ω

\( I = \dfrac{6}{30} = 0.2\ \text{A} \)

Thus, the reading of ammeter is 0.2 A.

Teacher's Note: Find the cell voltage from the first reading, then divide it by the new total resistance.

Exam Note: V = 6 V; I = 6/30 = 0.2 A.

Question 9. The circuit diagram is for a fan dryer that blows either hot air or cold air. Both switches R and S are as shown open. Which switch(es) is/are to be closed to obtain either hot or cold air?

SourceHeaterFanRS

Solution.

In this circuit if we want Hot air to come out of the hair dryer then we will have to close both the switches R and S. If we want cold air then we need to close the switch S. This will cause only the fan to work and the heater will be OFF and thus we’ll get cold air as an output.

(In both cases the unlabelled switch in the wire from the source must also be closed, so that current can flow.)

Teacher's Note: The heater and fan are in parallel branches with their own switches, so each can be switched independently.

Exam Note: Hot air: fan and heater on; cold air: fan only.

Class 10 Mathematics: All In One Solutions for All In One Solutions Class 10 Science Chapter 12 Electricity

Chapter-wise All In One Solutions: All In One Solutions Class 10 Science Chapter 12 Electricity

Explore reliable mathematical solutions for All In One Solutions Class 10 Science Chapter 12 Electricity tailored for Class 10 learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.

Step-by-Step Mathematical Explanations

Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.

Explore More Study Resources for Class 10 Math

Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.

FAQs

What are these [current-page:node:field_author] Solutions for Class 10 Science?

They are chapter-wise solved questions from the book for Class 10 Science. Each answer is explained step by step so you can check your work and revise.

Are the [current-page:node:field_author] Class 10 Science Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these [current-page:node:field_author] solutions for Class 10 Science?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising [current-page:node:field_author] Class 10 Science questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these Class 10 Science Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.