Xam Idea Solutions Class 10 Science Chapter 13 Magnetic Effects Of Electric Current Long Answer Type Questions

Solutions for Class 10 Science: Chapter 13 Magnetic Effects Of Electric Current

Explore reliable textbook solutions for Chapter 13 Magnetic Effects Of Electric Current tailored for Class 10 learners using methodologies. Utilizing these Science answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.

Practice Class 10 Science Solutions: Chapter 13 Magnetic Effects Of Electric Current

Navigate directly to the solved Science textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.

Long Answer Type Questions

Question 1. (i) Two circular coils P and Q are kept close to each other, of which coil P carries a current. If coil P is moved towards Q, will some current be induced in coil Q? Give reason for your answer and name the phenomenon involved. (ii) What happens if coil P is moved away from Q? (iii) State any two methods of inducing current in a coil.

Solution.

(i) When coil P is moved towards Q, current will be induced in coil Q. This is because on moving P the magnetic field associated with Q increases and so a current is induced. The Phenomenon is electromagnetic induction.

(ii) If P is moved away from Q, the field associated with Q will decrease and a current will be induced but in the opposite direction

(iii) Current can be induced in a coil by (a) moving a magnet towards or away from the coil (b) moving a coil towards or away from a magnet (c) rotating a coil within a magnetic field.

Teacher's Note: Moving a current-carrying coil near another changes the flux through it, inducing a current in the second coil.

Exam Note: Changing flux induces current.

Question 2. Briefly explain an activity to plot the magnetic field lines around a bar magnet. Sketch the field pattern for the same specifying field directions. A region A has magnetic field lines relatively closer than another region B. Which region has stronger magnetic field. Give reason to support your answer.

Solution.

1. Take a drawing sheet and fix it on a smooth table with adhesive tape.

2. Place a bar magnet in the middle of the drawing sheet and draw its boundary with a sharp pencil.

3. Place a magnetic compass near one end of the magnet (N-pole) and mark the positions of the two ends (N and S-poles) of the compass needle using a sharp pencil.

4. Shift the compass from this position and place it in such a way that S-pole of its needle is on the point you marked in previous step for N-pole.

5. Again mark the position of the other end (N-pole) of the compass needle.

6. Repeat the steps 4 and 5, till you reach the other end (S-pole) of the bar magnet.

7. Join all the points with a sharp pencil to get a smooth curve.

8. Put the compass at some other points near the N-pole of the magnet and draw another magnetic field lines. Similarly, draw many field lines on both the sides of the bar magnet as shown in figure.

NS

9. Observe the pattern of the magnetic field lines.

Result: Magnetic field lines can be drawn around a bar magnet using a magnetic compass. The field lines do not cross each other.

Region A has stronger magnetic field. This is due to the strength of the field is proportional to the relative closeness of field lines.

Teacher's Note: A compass needle aligns along the field; closely spaced lines indicate a stronger field.

Exam Note: Plot with compass, show N to S arrows; closer lines stronger.

Question 3. Briefly explain an activity to plot the magnetic field lines around a straight current carrying conductor. Sketch the field pattern for the same, specifying current and field directions. What happens to the field, (a) if the strength of the current is decreased? (b) if the direction of the current is reversed?

Solution.

The pattern of magnetic field lines around a straight conductor carrying current can be described by the following activity.

(i) Insert vertically a long straight wire carrying an electric current so that it passes through the centre of a horizontal piece of plastic board as shown in figure.

(ii) Take care that the plastic board is fixed and does not move up and down. Now, sprinkle some iron filings onto the plastic board to show the shape of the field.

Straight wire (current out of the paper), iron filings on plastic board

(iii) You will notice that the iron filings get arranged round the wire in the shape of circles. This is due to the reason that the magnetic field lines around the current carrying straight conductor are circular. The iron filings align along these field lines.

(iv) On reversing the direction of flow of current, we observe that the iron filings arrange themselves in circles around the wire showing that the magnetic field lines are still circular in nature.

The direction of the magnetic field can be obtained by using a compass. If the current direction is reversed, the direction of the magnetic field is also reversed.

(a) When current through the wire is decreased, field also gets reduced.

(b) When the current is reversed, field also gets reversed in direction.

Teacher's Note: Iron filings reveal circular field lines; field strength depends on current and its direction decides the field direction.

Exam Note: Circles around wire; weaker current weakens field; reversal reverses it.

Question 4. (a) Explain an activity to show that a current-carrying conductor experiences a force when placed in a magnetic field. (b) State the rule which gives the direction of force acting on the conductor. (c) An electron moves perpendicular to a magnetic field as shown in the figure. What would be the direction of force experienced on the electron?

ElectronMagnetic field

Solution.

(a) A small aluminium rod is suspended horizontally from a stand using two connecting wires. Place a strong horseshoe magnet in such a way that the rod lies between the two poles with the magnetic field directed upwards. For this, put the north pole of the magnet vertically below and south pole vertically above the aluminium rod. Connect the aluminium rod in series with a battery, a key and a rheostat. Pass a current through the aluminium rod from one end to other (B to A). The rod is displaced towards left. When the direction of current flowing through the rod is reversed, the rod is displaced towards right.

SNBAstand/wireskey + rheostat

(b) Fleming's left-hand rule. Stretch the thumb, forefinger and middle finger of your left hand such that they are mutually perpendicular to one another. If the forefinger points in the direction of magnetic field and the middle finger in the direction of current, then the thumb will point in the direction of motion or the force acting on the conductor.

(c) According to Fleming's left-hand rule, the direction of force is perpendicular to the direction of magnetic field and current. We know that the direction of current is taken opposite to the direction of motion of electrons. Therefore, the force is directed upwards from the plane of the paper.

Teacher's Note: The force on a current-carrying conductor is perpendicular to both field and current, given by Fleming's left-hand rule.

Exam Note: Rod deflects; state left-hand rule; reverse current reverses force.

Question 5. With the help of a diagram, describe an experiment to show that a change in current flowing through a coil induces an electric current in a neighbouring coil.

Coil 1Coil 2KG

Solution.

Take two different coils of insulated copper wire having large number of turns (50 or even more). Insert the coils over a non-conducting cylindrical thick paper roll as shown in figure. Connect a battery of 6 V, a plug key K in series of coil-1. With coil-2 connect a sensitive galvanometer. Now put the plug in key K. Galvanometer joined with coil-2 also gives a momentary deflection and then pointer quickly returns to its mean position. On removing plug from key K in coil-1 the needle momentarily moves, but to the opposite side. It means that now the current flows in the opposite direction in coil 2. So we conclude that current is produced in coil-2 whenever the current flowing in the neighbouring coil is changing.

Teacher's Note: A changing current in one coil changes the magnetic flux through the other, inducing a momentary current.

Exam Note: Make or break circuit; galvanometer deflects momentarily.

Question 6. Draw an appropriate schematic diagram showing common domestic circuits and discuss the importance of fuse. Why is it that a burnt out fuse should be replaced by another fuse of identical rating?

Live wireNeutral wireEarth wiremain fusekWhmetermain switch+ fusesappliances (in parallel)

Solution.

A fuse in a circuit prevents damage to the appliances and the circuit due to overloading. Otherwise, the appliances or the circuit may be damaged.

When current in the circuit exceeds the value of fuse rating, the fuse wire melts due to heating. This causes a gap in the circuit and the current stops flowing in the circuit.

A burnt-out fuse must be replaced by one of identical rating. A fuse of higher rating will not melt at the current the circuit wiring can safely carry, so wires and appliances may overheat and cause a fire. A fuse of lower rating will blow even during normal use.

Teacher's Note: The fuse wire melts when current exceeds its rating, breaking the circuit and protecting wiring and appliances.

Exam Note: Fuse melts on overload; use same rating.

Question 7. (i) With the help of an activity, explain the method of inducing electric current in a coil with a moving magnet. State the rule used to find the direction of electric current thus generated in the coil. (ii) Two circular coils P and Q are kept close to each other, of which coil P carries a current. What will you observe in Q? (a) If current in the coil P is changed? (b) If both the coils are moved in the same direction with the same speed? Give reason.

Solution.

(i) Activity:

(a) Take a coil of wire AB having a large number of turns.

(b) Connect the ends of the coil to a galvanometer.

ABGNSmagnet moved towards coil

(c) Take a strong bar magnet and move its north pole towards the end B of the coil.

(d) There is a momentary deflection in the needle of the galvanometer, say to the right. This indicates the presence of a current in the coil AB. The deflection becomes zero the moment the motion of the magnet stops.

(e) Now withdraw the north pole of the magnet away from the coil. Now the galvanometer is deflected toward the left, showing that the current is now set up in the direction opposite to the first.

(f) Place the magnet stationary near the coil. The deflection of the galvanometer drops to zero when the coil and magnet are at rest with respect to each other. The needle deflects only when there is relative motion between the coil and the magnet.

To find the direction of electric current, Fleming's right-hand rule is applied. According to it, if we stretch the forefinger, middle finger and thumb of our right hand mutually perpendicular in such a way that thumb points along the direction of motion of conductor, forefinger along the direction of magnetic field; then the middle finger points along the direction of induced current.

(ii) (a) When current in P is changed, the field associated with Q will vary causing an induced current in Q.

(b) If both the coils are moved in the same direction with same speed, there will not be any change in the field associated with Q. Hence no current will be induced in Q.

Teacher's Note: Relative motion between magnet and coil changes the flux through the coil, inducing a current.

Exam Note: Relative motion induces current; same-speed motion induces none.

Question 8. Explain the underlying principle and working of direct current generator (or DC dynamo) by drawing a labelled diagram.

ABCDNSR₁R₂B₁B₂GArmature coil ABCD in field between N and S

Solution.

A device used to convert mechanical energy into electrical energy is called an electric generator. An armature-coil rotating in a magnetic field develops an alternating emf and sends alternating current in an external circuit. If, however, the connections of the ends of the coil to the external circuit are interchanged every time the emf in the coil reverses, the current in the external circuit flows always in the same direction. This is the principle of a DC dynamo.

The working of a single-coil DC dynamo is shown in the figure. The ends of the armature-coil ABCD are connected to the two separated halves R1 and R2 of a single copper ring R, which is called the 'split-ring commutator'. R1 and R2 rotate along with the armature between two brushes B1 and B2 to which the external circuit is connected.

When the armature-coil ABCD is rotated clockwise (say), an emf is induced in the coil and a current flows in the direction ABCD (Fleming's right-hand rule). In the external circuit, the current flows from B1 to B2. For half the revolution, R1 is in contact with B1 and R2 with B2. But as soon as the coil passes the vertical, R1 comes in contact with B2 and R2 with B1 and remain so during the next half revolution. Although the induced emf in the coil is reversed and the current in the coil flows in the direction DCBA, in the external circuit the current still flows from B1 to B2.

The current generated by such a simple dynamo is unidirectional. As long as the coil is rotating, the direct current flows through the device connected to the terminals of the generator.

Teacher's Note: A split-ring commutator reverses coil connections every half turn, keeping the external current in one direction.

Exam Note: Principle: electromagnetic induction plus commutator; label parts.

Question 9. (a) With the help of a labelled diagram, explain the distribution of magnetic field due to a current through a circular loop. Why is it that if a current carrying coil has n turns the field produced at any point is n times as large as that produced by a single turn? (b) Draw a pattern of magnetic field formed around a current carrying solenoid. What happens to the magnetic field when the current through the solenoid is reversed?

Solution.

(a) The pattern of the magnetic field lines near the wires of the coil are concentric circles. The diameter of these circles goes on increasing as we move away from the wire. At the centre of the circular loop, the field lines are nearly straight and parallel.

•Circular loop of current-carrying wire; field near the centre is straight and parallel

In a coil of n turns, the current in every turn flows in the same direction, so the fields due to the individual turns add up in the same direction. The field is therefore n times that of a single turn.

(b) The field pattern around a current-carrying solenoid is shown below; it is similar to that of a bar magnet. When the current through the solenoid is reversed, the magnetic field also gets reversed.

NSSolenoid: field inside is uniform and along the axis

Teacher's Note: Fields of all turns point the same way and add. A solenoid behaves like a bar magnet.

Exam Note: Turns add fields; solenoid like bar magnet; reversal reverses field.

Xam Idea Solutions for Class 10 Mathematics: Xam Idea Solutions Class 10 Science Chapter 13 Magnetic Effects Of Electric Current Long Answer Type Questions

Download Xam Idea Solutions for Class 10

Review detailed solutions for Class 10 Mathematics. The Xam Idea Solutions Class 10 Science Chapter 13 Magnetic Effects Of Electric Current Long Answer Type Questions PDF provides comprehensive answers mapped to standard Xam Idea Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.

Concept-Driven Math Answers

Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.

Complete Your Class 10 Exam Preparation

In addition to these Xam Idea Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.

FAQs

What are these [current-page:node:field_author] Solutions for Class 10 Science?

They are chapter-wise solved questions from the book for Class 10 Science. Each answer is explained step by step so you can check your work and revise.

Are the [current-page:node:field_author] Class 10 Science Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these [current-page:node:field_author] solutions for Class 10 Science?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising [current-page:node:field_author] Class 10 Science questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these Class 10 Science Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.