Pradeep's KL Gogia Solutions for Class 11 Physics: Chapter 03 Elasticity
Review structured textbook solutions for Class 11 Physics Chapter 03 Elasticity prepared by Pradeep's KL Gogia. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Practice Class 11 Physics Solutions: Chapter 03 Elasticity
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Elasticity - Sample Problems 1-46
Sample problems based on Stress
Question 1. A and B are two wires. The radius of A is twice that of B. They are stretched by the same load. Then the stress on B is: (a) Equal to that on A (b) Four times that on A (c) Two times that on A (d) Half that on A [MP PMT 1993]
Solution. (b) Stress = Force/Area = F/(πr²). So stress ∝ 1/r², giving (Stress)B/(Stress)A = (rA/rB)² = (2)² , i.e. (Stress)B = 4 × (Stress)A [as F is constant].
Teacher's Note: For the same load, stress varies inversely as the square of the radius, so the thinner wire carries more.
Exam Note: Write stress ∝ 1/r² first.
Question 2. One end of a uniform wire of length L and of weight W is attached rigidly to a point in the roof and a weight W1 is suspended from its lower end. If S is the area of cross-section of the wire, the stress in the wire at a height 3L/4 from its lower end is: (a) W1/S (b) [W1 + (W/4)]/S (c) [W1 + (3W/4)]/S (d) (W1 + W)/S
Solution. (c) As the wire is uniform, the weight of the wire below point P (at height 3L/4 from the lower end) is 3W/4. Total force at P = W1 + 3W/4 and area of cross-section = S. Stress at P = Force/Area = [W1 + (3W/4)]/S.
Teacher's Note: Tension at a point equals the hanging load plus the weight of the wire portion below that point.
Exam Note: Count only the wire length below P.
Question 3. On suspending a weight Mg, the length l of an elastic wire of area of cross-section A becomes double the initial length. The instantaneous stress acting on the wire is: (a) Mg/A (b) Mg/2A (c) 2Mg/A (d) 4Mg/A
Solution. (c) When the length of the wire becomes double, its area of cross-section becomes half because the volume of the wire is constant (V = AL). So the instantaneous stress = Force/Area = Mg/(A/2) = 2Mg/A.
Teacher's Note: Constant volume means doubling the length halves the area, so true stress doubles.
Exam Note: Use the new area A/2.
Question 4. A bar is subjected to equal and opposite forces F as shown in the figure. PQRS is a plane making angle θ with the cross-section of the bar. If the area of cross-section is A, what is the tensile stress on PQRS? (a) F/A (b) F cosθ/A (c) F cos²θ/A (d) F/(A cosθ)
Solution. (c) Tensile stress = Normal force/Area = FN/AN. Here AN = A/cosθ and FN = normal force = F cosθ. So tensile stress = F cosθ/(A/cosθ) = F cos²θ/A.
Teacher's Note: On an inclined plane resolve F normally; the plane's area is larger, A/cosθ.
Exam Note: Show FN and AN separately.
Question 5. In the above question, what is the shearing stress on PQ? (a) F/(A cosθ) (b) F sin2θ/2A (c) F/(2A sin2θ) (d) F cosθ/A
Solution. (b) Shear stress = Tangential force/Area = F sinθ/(A/cosθ) = F sinθ cosθ/A = F sin2θ/2A.
Teacher's Note: The tangential component is F sinθ; divide by the inclined area A/cosθ, then use sin2θ.
Exam Note: Quote sinθcosθ = sin2θ/2.
Question 6. In the above question, when is the tensile stress maximum? (a) θ = 0° (b) θ = 30° (c) θ = 45° (d) θ = 90°
Solution. (a) Tensile stress = F cos²θ/A. It is maximum when cos²θ is maximum, i.e. cosθ = 1 ⇒ θ = 0°.
Teacher's Note: At θ = 0 the plane is the cross-section itself, where the full force acts normally.
Exam Note: State cos²θ = 1 at θ = 0.
Question 7. In the above question, when is the shearing stress maximum? (a) θ = 0° (b) θ = 30° (c) θ = 45° (d) θ = 90°
Solution. (c) Shearing stress = F sin2θ/2A. It is maximum when sin2θ is maximum, i.e. sin2θ = 1 ⇒ 2θ = 90° ⇒ θ = 45°.
Teacher's Note: Maximum shear on a plane at 45° to the axis explains why ductile bars slip along 45° planes.
Exam Note: Set sin2θ = 1 to get 45°.
9.8 Strain: Sample problems based on Strain
Question 8. A cube of aluminium of sides 0.1 m is subjected to a shearing force of 100 N. The top face of the cube is displaced through 0.02 cm with respect to the bottom face. The shearing strain would be: (a) 0.02 (b) 0.1 (c) 0.005 (d) 0.002 [MP PAT 1990]
Solution. (d) Shearing strain φ = x/L = 0.02 cm/0.1 m = 0.0002 m/0.1 m = 0.002.
Teacher's Note: Shearing strain is displacement over height; convert 0.02 cm to metres first.
Exam Note: Unit conversion earns the mark.
Question 9. A wire is stretched to double its length. The strain is: (a) 2 (b) 1 (c) Zero (d) 0.5
Solution. (b) Strain = Change in length/Original length = (2L − L)/L = 1.
Teacher's Note: Strain uses the change in length, not the final length; doubling gives strain 1.
Exam Note: Do not answer 2.
Question 10. The length of a wire increases by 1% by a load of 2 kg-wt. The linear strain produced in the wire will be: (a) 0.02 (b) 0.001 (c) 0.01 (d) 0.002
Solution. (c) Strain = Change in length/Original length = (1% of L)/L = (L/100)/L = 0.01.
Teacher's Note: A percentage extension is directly the strain as a decimal; the load value is not needed.
Exam Note: 1% means 0.01.
Sample problems based on Stress-strain curve
Question 11. The stress-strain curves for brass, steel and rubber are shown in the figure. The lines A, B and C are for: (a) Rubber, brass and steel respectively (b) Brass, steel and rubber respectively (c) Steel, brass and rubber respectively (d) Steel, rubber and brass respectively
Solution. (c) From the graph tanθC < tanθB < tanθA ⇒ YC < YB < YA. ∴ YRubber < YBrass < YSteel. So A is steel, B is brass, C is rubber.
Teacher's Note: On a stress-strain graph the slope is Young's modulus; steepest line is steel, shallowest is rubber.
Exam Note: Rank by slope, then name materials.
Question 12. The strain-stress curves of three wires of different materials are shown in the figure. P, Q and R are the elastic limits of the wires. The figure shows that: (a) Elasticity of wire P is maximum (b) Elasticity of wire Q is maximum (c) Tensile strength of R is maximum (d) None of the above is true
Solution. (d) On the graph, stress is represented on the X-axis and strain on the Y-axis. So from the graph Y = cotθ = 1/tanθ ∝ 1/θ, where θ is the angle from the stress axis. ∴ YP < YQ < YR [as θP > θQ > θR]. We can say that elasticity of wire P is minimum and R is maximum.
Teacher's Note: Axes are swapped here, so Young's modulus is the inverse slope; the steepest line has the least Y.
Exam Note: Check which axis is stress.
Sample problems based on Young's modulus
Question 13. The diameter of a brass rod is 4 mm and Young's modulus of brass is 9 × 1010 N/m². The force required to stretch it by 0.1% of its length is: (a) 360π N (b) 36 N (c) 144π × 103 N (d) 36π × 105 N [MP PET 1991; BVP 2003]
Solution. (a) r = 2 × 10−3 m, Y = 9 × 1010 N/m², l = 0.1% of L ⇒ l/L = 0.001. As Y = (F/A)/(l/L), F = YA(l/L) = 9 × 1010 × π(2 × 10−3)² × 0.001 = 360π N.
Teacher's Note: Use radius, not diameter, in A = πr²; 0.1% means strain 0.001.
Exam Note: Halve the diameter before squaring.
Question 14. A wire of length 2 m is made from 10 cm³ of copper. A force F is applied so that its length increases by 2 mm. Another wire of length 8 m is made from the same volume of copper. If the force F is applied to it, its length will increase by: (a) 0.8 cm (b) 1.6 cm (c) 2.4 cm (d) 3.2 cm [MP PET 2003]
Solution. (d) l = FL/(AY) = FL²/(VY) ∴ l ∝ L² [as V, Y and F are constant]. l2/l1 = (L2/L1)² = (8/2)² = 16 ⇒ l2 = 16 l1 = 16 × 2 mm = 32 mm = 3.2 cm.
Teacher's Note: At fixed volume, A = V/L, so extension grows as the square of the length.
Exam Note: Convert 32 mm to 3.2 cm.
Question 15. A wire of length L and radius r is rigidly fixed at one end. On stretching the other end of the wire with a force F, the increase in its length is l. If another wire of same material but of length 2L and radius 2r is stretched with a force of 2F, the increase in its length will be: (a) l (b) 2l (c) l/2 (d) l/4 [AIIMS 1980; MP PAT 1990; MP PET 1989, 92; MP PET/PMT 1988; MP PMT 1996, 2002; UPSEAT 2002]
Solution. (a) l = FL/(πr²Y) ⇒ l2/l1 = (F2/F1)(L2/L1)(r1/r2)² = 2 × 2 × (1/2)² = 1. ∴ l2 = l1, i.e. the increment in length will be the same.
Teacher's Note: Extension ∝ FL/r²; the factors 2, 2 and 1/4 cancel to give 1.
Exam Note: Square the radius ratio.
Question 16. Two wires A and B are of same materials. Their lengths are in the ratio 1 : 2 and diameters are in the ratio 2 : 1 when stretched by force FA and FB respectively they get equal increase in their lengths. Then the ratio FA/FB should be: (a) 1 : 2 (b) 1 : 1 (c) 2 : 1 (d) 8 : 1 [Orissa JEE 2002]
Solution. (d) Y = FL/(πr²l) ∴ F = Yπr² l/L. FA/FB = (YA/YB)(rA/rB)²(lA/lB)(LB/LA) = 1 × (2/1)² × (1) × (2/1) = 8.
Teacher's Note: For equal extension F ∝ r²/L; the thicker, shorter wire needs more force.
Exam Note: Invert the length ratio.
Question 17. A uniform plank of Young's modulus Y is moved over a smooth horizontal surface by a constant horizontal force F. The area of cross-section of the plank is A. The compressive strain on the plank in the direction of the force is: (a) F/AY (b) 2F/AY (c) (1/2)(F/AY) (d) 3F/AY [Kerala (Engg.) 2002]
Solution. (a) Compressive strain = Stress/Young's modulus = (F/A)/Y = F/AY.
Teacher's Note: Strain is stress divided by Y; the force acts on the full cross-section A.
Exam Note: Apply Y = stress/strain directly.
Question 18. A wire is stretched by 0.01 m by a certain force F. Another wire of same material whose diameter and length are double to the original wire is stretched by the same force. Then its elongation will be: (a) 0.005 m (b) 0.01 m (c) 0.02 m (d) 0.002 m [EAMCET (Engg.) 1995; CPMT 2001]
Solution. (a) l = FL/(πr²Y) ∴ l ∝ L/r² [as F and Y are constants]. l2/l1 = (L2/L1)(r1/r2)² = (2)(1/2)² = 1/2 ⇒ l2 = l1/2 = 0.01/2 = 0.005 m.
Teacher's Note: Doubling length doubles extension but doubling radius cuts it to a quarter; net one half.
Exam Note: Diameter doubled means radius doubled.
Question 19. The length of an elastic string is a metres when the longitudinal tension is 4 N and b metres when the longitudinal tension is 5 N. The length of the string in metres when the longitudinal tension is 9 N is: (a) a − b (b) 5b − 4a (c) 2b − a/4 (d) 4a − 3b [EAMCET 2001]
Solution. (b) Let the original length of the elastic string be L and its force constant be k. When longitudinal tension 4 N is applied: L + 4/k = a ......(i). When tension 5 N is applied: L + 5/k = b ......(ii). By solving (i) and (ii) we get k = 1/(b − a) and L = 5a − 4b. Now when longitudinal tension 9 N is applied, its length = L + 9/k = 5a − 4b + 9(b − a) = 5b − 4a.
Teacher's Note: Length is natural length plus T/k; two readings fix L and k, then extrapolate.
Exam Note: Subtract (i) from (ii) first.
Question 20. The load versus elongation graph for four wires of the same material is shown in the figure. The thickest wire is represented by the line: (a) OD (b) OC (c) OB (d) OA [KCET (Engg./Med.) 2001]
Solution. (a) Young's modulus Y = FL/(Al) ∴ l ∝ 1/A (as Y, L and F are constant). From the graph it is clear that for the same load, elongation is minimum for graph OD. As elongation (l) is minimum, therefore area of cross-section (A) is maximum. So the thickest wire is represented by OD.
Teacher's Note: Steepest load-elongation line means least stretch per load, so largest area.
Exam Note: Link slope to area through l ∝ 1/A.
Question 21. A 5 m long aluminium wire (Y = 7 × 1010 N/m²) of diameter 3 mm supports a 40 kg mass. In order to have the same elongation in a copper wire (Y = 12 × 1010 N/m²) of the same length under the same weight, the diameter should now be, in mm: (a) 1.75 (b) 2.0 (c) 2.3 (d) 5.0
Solution. (c) l = FL/(πr²Y) = 4FL/(πd²Y) [as r = d/2]. If the elongations in both wires (of same length) are the same under the same weight then d²Y = constant. (dCu/dAl)² = YAl/YCu ⇒ dCu = dAl × √(YAl/YCu) = 3 × √(7 × 1010/12 × 1010) = 2.29 mm.
Teacher's Note: Same F, L and extension give d²Y constant; stiffer copper needs a thinner wire.
Exam Note: Take the square root of 7/12.
Question 22. On applying a stress of 20 × 108 N/m² the length of a perfectly elastic wire is doubled. Its Young's modulus will be: (a) 40 × 108 N/m² (b) 20 × 108 N/m² (c) 10 × 108 N/m² (d) 5 × 108 N/m² [MP PET 2000]
Solution. (b) When strain is unity then Young's modulus is equal to stress. Doubling the length gives strain 1, so Y = 20 × 108 N/m².
Teacher's Note: Doubled length means strain 1, so Y equals the applied stress numerically.
Exam Note: Strain = (2L − L)/L = 1.
Question 23. The dimensions of four wires of the same material are given below. In which wire the increase in length will be maximum when the same tension is applied: (a) Length 100 cm, diameter 1 mm (b) Length 200 cm, diameter 2 mm (c) Length 300 cm, diameter 3 mm (d) Length 50 cm, diameter 0.5 mm [IIT-JEE 1981; NCERT 1976; CPMT 1983, 90; MP PMT 1992, 94, 97; MP PET/PMT 1998; MP PMT 1989, 90, 99]
Solution. (d) If the same force is applied on four wires of same material then elongation in each wire depends on the length and diameter of the wire and is given by l ∝ L/d², and the ratio of L/d² is maximum for option (d). (Check: L/d² in cm/mm² is 100, 50, 33.3 and 200 for (a), (b), (c), (d).)
Teacher's Note: Compare L/d² for each wire; the thin short wire wins because d is squared.
Exam Note: Tabulate L/d² for all four.
Sample problems based on Young's modulus (continued)
Question 24. The Young's modulus of a wire of length L and radius r is Y N/m². If the length and radius are reduced to L/2 and r/2, then its Young's modulus will be: (a) Y/2 (b) Y (c) 2Y (d) 4Y [MP PMT 1985; MP PET 1997; KCET (Engg./Med.) 1999]
Solution. (b) Young's modulus does not depend upon the dimensions of the wire. It is constant for a given material of wire.
Teacher's Note: Y is a material property; only force constant k = YA/L depends on dimensions.
Exam Note: Say Y is independent of size.
Question 25. A fixed volume of iron is drawn into a wire of length L. The extension x produced in this wire by a constant force F is proportional to: (a) 1/L² (b) 1/L (c) L² (d) L
Solution. (c) l = FL/(AY) = FL²/(ALY) = FL²/(VY); for a fixed volume l ∝ L².
Teacher's Note: Fixed volume gives A = V/L, so the extension depends on L squared.
Exam Note: Replace A by V/L.
Question 26. A rod is fixed between two points at 20°C. The coefficient of linear expansion of material of rod is 1.1 × 10−5/°C and Young's modulus is 1.2 × 1011 N/m². Find the stress developed in the rod if temperature of rod becomes 10°C. (a) 1.32 × 107 N/m² (b) 1.10 × 1015 N/m² (c) 1.32 × 108 N/m² (d) 1.10 × 106 N/m²
Solution. (a) Thermal stress = F/A = YαΔθ = 1.2 × 1011 × 1.1 × 10−5 × (20 − 10) = 1.32 × 107 N/m².
Teacher's Note: A rod clamped at both ends develops stress YαΔθ; cooling makes it tensile.
Exam Note: Use the magnitude of Δθ = 10°C.
Question 27. The coefficient of linear expansion of brass and steel are α1 and α2. If we take a brass rod of length L1 and steel rod of length L2 at 0°C, their difference in length (L2 − L1) will remain the same at any temperature if: (a) α1L2 = α2L1 (b) α1L22 = α22L1 (c) α12L1 = α22L2 (d) α1L1 = α2L2 [EAMCET (Med.) 1995]
Solution. (d) The difference in lengths of the rods will remain the same if expansion is the same in both rods. If expansion in the first rod is l1 = L1α1Δθ and expansion in the second rod is l2 = L2α2Δθ, then L1α1Δθ = L2α2Δθ ∴ L1α1 = L2α2.
Teacher's Note: A constant length difference needs equal absolute expansions, so L·α must match.
Exam Note: Equate l1 and l2.
Question 28. The force required to stretch a steel wire of 1 cm² cross-section to 1.1 times its length would be (Y = 2 × 1011 N m−2): (a) 2 × 106 N (b) 2 × 103 N (c) 2 × 10−6 N (d) 2 × 10−7 N [MP PET 1992]
Solution. (a) L2 = 1.1 L1 ∴ Strain = l/L1 = (L2 − L1)/L1 = (1.1L1 − L1)/L1 = 0.1. F = YA(l/L) = 2 × 1011 × 1 × 10−4 × 0.1 = 2 × 106 N.
Teacher's Note: Stretching to 1.1 times gives strain 0.1, not 1.1; convert 1 cm² to 10−4 m².
Exam Note: Strain is change over original.
Question 29. A two metre long rod is suspended with the help of two wires of equal length. One wire is of steel and its cross-sectional area is 0.1 cm² and another wire is of brass and its cross-sectional area is 0.2 cm². If a load W is suspended from the rod and stress produced in both the wires is the same then the ratio of tensions in them will be: (a) Will depend on the position of W (b) T1/T2 = 2 (c) T1/T2 = 1 (d) T1/T2 = 0.5
Solution. (d) Stress = Tension/Area of cross-section = constant. ∴ T1/A1 = T2/A2 ⇒ T1/T2 = A1/A2 = 0.1/0.2 = 1/2 = 0.5.
Teacher's Note: Equal stress means tension is proportional to cross-sectional area, whatever the material.
Exam Note: Ignore Y; use area ratio.
Question 30. Three blocks, each of same mass m, are connected with wires W1 and W2 of same cross-sectional area a and Young's modulus Y. Neglecting friction the strain developed in wire W2 is: (a) 2mg/3aY (b) 3mg/2aY (c) 1mg/3aY (d) 3mg/aY
Solution. (a) If the system moves with acceleration a and T is the tension in the string W2 then by comparing with the standard case, T = m1m2g/(m1 + m2). In the given problem m1 = (m + m) = 2m and m2 = m. ∴ Tension = m · 2m · g/(m + 2m) = (2/3)mg. ∴ Stress = T/a = 2mg/3a and Strain = Stress/(Young's modulus) = 2mg/(3aY).
Teacher's Note: W2 pulls the two table blocks (2m) with the hanging m; tension is 2mg/3, then divide by aY.
Exam Note: Find tension before strain.
Question 31. A wire elongates by 1.0 mm when a load W is hanged from it. If this wire goes over a pulley and two weights W each are hung at the two ends, the elongation of the wire will be: (a) 0.5 m (b) 1.0 mm (c) 2.0 mm (d) 4.0 mm
Solution. (b) Elongation in the wire ∝ Tension in the wire. In the first case T1 = W and in the second case T2 = 2W × W/(W + W) = W. As T1/T2 = 1 ∴ l1/l2 = 1 ⇒ l2 = l1 = 1.0 mm.
Teacher's Note: Over a pulley with equal weights each side the tension is only W, so the stretch is unchanged.
Exam Note: Tension is W, not 2W.
Question 32. The Young's modulus of three materials are in the ratio 2 : 2 : 1. Three wires made of these materials have their cross-sectional areas in the ratio 1 : 2 : 3. For a given stretching force the elongations in the three wires are in the ratio: (a) 1 : 2 : 3 (b) 3 : 2 : 1 (c) 5 : 4 : 3 (d) 6 : 3 : 4
Solution. (d) l = FL/(AY) and for a given stretching force l ∝ 1/(AY). Let the three wires have Young's modulus 2Y, 2Y and Y and cross-sectional areas A, 2A and 3A respectively. l1 : l2 : l3 = 1/(A·2Y) : 1/(2A·2Y) : 1/(3A·Y) = 1/2 : 1/4 : 1/3 = 6 : 3 : 4.
Teacher's Note: Elongation ∝ 1/(AY); put fractions over 12 to get the integer ratio.
Exam Note: Assume equal lengths.
Question 33. A light rod with uniform cross-section of 10−4 m² is shown in the adjoining figure. The rod consists of three different materials whose lengths are 0.1 m, 0.2 m and 0.15 m respectively and whose Young's moduli are 2.5 × 1010 N/m², 4 × 1010 N/m² and 1 × 1010 N/m² respectively. The displacement of point B will be: (a) 24 × 10−6 m (b) 9 × 10−6 m (c) 4 × 10−6 m (d) 1 × 10−6 m
Solution. (c) Increment in the length AB = MgL/(AY) = (10 × 10 × 0.1)/(10−4 × 2.5 × 1010) = 4 × 10−6 m. ∴ Displacement of point B = 4 × 10−6 m.
Teacher's Note: Point A is fixed, so B's displacement is just the extension of segment AB (g = 10 m/s²).
Exam Note: Use g = 10 as the book does.
Question 34. In the above problem, the displacement of point C will be: (a) 24 × 10−6 m (b) 9 × 10−6 m (c) 4 × 10−6 m (d) 1 × 10−6 m
Solution. (b) Increment in the length BC = MgL/(AY) = (10 × 10 × 0.2)/(10−4 × 4 × 1010) = 5 × 10−6 m. ∴ Displacement of point C = 4 × 10−6 + 5 × 10−6 = 9 × 10−6 m.
Teacher's Note: Displacements add along the rod: C moves by AB's extension plus BC's extension.
Exam Note: Add the previous displacement.
Question 35. In the above problem, the displacement of point D will be: (a) 24 × 10−6 m (b) 9 × 10−6 m (c) 4 × 10−6 m (d) 1 × 10−6 m
Solution. (a) Increment in the length CD = MgL/(AY) = (10 × 10 × 0.15)/(10−4 × 1 × 1010) = 15 × 10−6 m. ∴ Displacement of point D = 4 × 10−6 + 5 × 10−6 + 15 × 10−6 = 24 × 10−6 m.
Teacher's Note: Total extension of the rod is the sum of the three segment extensions, each under the same 100 N.
Exam Note: Sum all three segments.
Question 36. Two blocks of masses m1 and m2 are joined by a wire of Young's modulus Y via a massless pulley. The area of cross-section of the wire is S and its length is L. When the system is released, the increase in length of the wire is: (a) m1m2gL/[YS(m1 + m2)] (b) 2m1m2gL/[YS(m1 + m2)] (c) (m1 − m2)gL/[YS(m1 + m2)] (d) 4m1m2gL/[YS(m1 + m2)]
Solution. (b) Tension in the wire T = 2m1m2g/(m1 + m2) ∴ stress in the wire = T/S = 2m1m2g/[S(m1 + m2)]. ∴ Strain l/L = Stress/Y = 2m1m2g/[YS(m1 + m2)] ⇒ l = 2m1m2gL/[YS(m1 + m2)].
Teacher's Note: In a released Atwood machine the string tension is 2m1m2g/(m1 + m2), not a weight.
Exam Note: Find T first, then l = TL/YS.
Question 37. A steel wire of diameter d, area of cross-section A and length 2L is clamped firmly at two points A and B which are 2L metre apart and in the same plane. A body of mass m is hung from the middle point of wire such that the middle point of wire sags by x lower from original position. If Young's modulus is Y then m is given by: (a) (1/2)YAx²/(gL²) (b) (1/2)YAL²/(gx²) (c) YAx³/(gL³) (d) YAL³/(gx²)
Solution. (c) Let the tension in the wire be T and for the equilibrium of mass m: 2T sinθ = mg ⇒ T = mg/(2 sinθ) = mgL/(2x) [as θ is small, sinθ ≈ x/L]. Increment in the length (each half) l = AC − AB = √(L² + x²) − L = (L² + x²)1/2 − L = L[(1 + x²/L²)1/2 − 1] = L[1 + x²/(2L²) − 1] = x²/(2L). As Young's modulus Y = (T/A)(L/l), ∴ T = YAl/L. Substituting the values of T and l: mgL/(2x) = (YA/L)(x²/2L) ∴ m = YAx³/(gL³).
Teacher's Note: Small sag: binomial expansion gives extension x²/2L per half; balance the vertical forces.
Exam Note: State the small-angle approximation used.
Question 38. Two wires of equal length and cross-section are suspended as shown. Their Young's moduli are Y1 and Y2 respectively. The equivalent Young's modulus will be: (a) Y1 + Y2 (b) (Y1 + Y2)/2 (c) Y1Y2/(Y1 + Y2) (d) √(Y1Y2)
Solution. (b) Let the equivalent Young's modulus of the given combination be Y and the area of cross-section 2A. For a parallel combination k1 + k2 = keq: Y1A/L + Y2A/L = Y·2A/L, so Y1 + Y2 = 2Y ∴ Y = (Y1 + Y2)/2.
Teacher's Note: Wires side by side are springs in parallel; force constants add and total area is 2A.
Exam Note: Divide by 2 for doubled area.
Question 39. If a load of 9 kg is suspended on a wire, the increase in length is 4.5 mm. The force constant of the wire is: (a) 0.49 × 104 N/m (b) 1.96 × 104 N/m (c) 4.9 × 104 N/m (d) 0.196 × 104 N/m
Solution. (b) Force constant k = F/l = mg/l = (9 × 9.8)/(4.5 × 10−3) ⇒ k = 1.96 × 104 N/m.
Teacher's Note: Force constant is force per unit extension; convert 4.5 mm to metres.
Exam Note: Use F = mg in newtons.
Question 40. One end of a long metallic wire of length L, area of cross-section A and Young's modulus Y is tied to the ceiling. The other end is tied to a massless spring of force constant k. A mass m hangs freely from the free end of the spring. It is slightly pulled down and released. Its time period is given by: (a) 2π√(m/K) (b) 2π√(mYA/KL) (c) 2π√(mK/YA) (d) 2π√[m(KL + YA)/(KYA)]
Solution. (d) Force constant of wire k1 = F/l = YA/L and force constant of spring k2 = k (given). Equivalent force constant for the given (series) combination: 1/keq = 1/k1 + 1/k2 = L/YA + 1/k ⇒ keq = kYA/(kL + YA). ∴ Time period T = 2π√(m/keq) = 2π√[m(kL + YA)/(kYA)].
Teacher's Note: Wire and spring are in series, so reciprocals of force constants add, then T = 2π√(m/keq).
Exam Note: Use k = YA/L for the wire.
Question 41. Two wires A and B have the same length and area of cross section. But Young's modulus of A is two times the Young's modulus of B. Then the ratio of force constant of A to that of B is: (a) 1 (b) 2 (c) 1/2 (d) √2
Solution. (b) Force constant of wire k = YA/L ⇒ kA/kB = YA/YB = 2 [as L and A are same].
Teacher's Note: With equal L and A, force constant is directly proportional to Young's modulus.
Exam Note: Quote k = YA/L.
9.12 Work Done in Stretching a Wire: Sample problems
Question 42. A wire suspended vertically from one of its ends is stretched by attaching a weight of 200 N to the lower end. The weight stretches the wire by 1 mm, then the elastic energy stored in the wire is: (a) 0.1 J (b) 0.2 J (c) 10 J (d) 20 J
Solution. (a) Elastic energy stored in wire = U = (1/2)Fl = (1/2) × 200 × 1 × 10−3 = 0.1 J.
Teacher's Note: Stored energy is half of force times extension, the area under the force-extension line.
Exam Note: Do not forget the factor 1/2.
Question 43. The graph shows the behaviour of a length of wire in the region for which the substance obeys Hooke's law. P and Q represent: (a) P = applied force, Q = extension (b) P = extension, Q = applied force (c) P = extension, Q = stored elastic energy (d) P = stored elastic energy, Q = extension [AMU 2001]
Solution. (c) The graph between applied force and extension will be a straight line because in the elastic range applied force ∝ extension, but the graph between extension and stored elastic energy will be parabolic in nature. As U = (1/2)kx², or U ∝ x².
Teacher's Note: A curved, upward-bending graph means a square law; U ∝ x² fits extension against energy.
Exam Note: Force-extension would be a straight line.
Question 44. When a 4 kg mass is hung vertically on a light spring that obeys Hooke's law, the spring stretches by 2 cm. The work required to be done by an external agent in stretching this spring by 5 cm will be (g = 9.8 m/s²): (a) 4.900 J (b) 2.450 J (c) 0.495 J (d) 0.245 J [MP PMT 1995]
Solution. (b) When a 4 kg mass is hung vertically on a spring, it stretches by 2 cm ∴ k = F/x = (4 × 9.8)/(2 × 10−2) = 1960 N/m. Now work done in stretching this spring by 5 cm: U = (1/2)kx² = (1/2) × 1960 × (5 × 10−2)² = 2.45 J.
Teacher's Note: Find k from the hanging mass, then work equals (1/2)kx² for the new stretch.
Exam Note: Convert cm to m before squaring.
Question 45. A rod of iron of Young's modulus Y = 2.0 × 1011 N/m² just fits the gap between two rigid supports 1 m apart. If the rod is heated through 100°C the strain energy of the rod is (α = 18 × 10−6 °C−1 and area of cross-section A = 1 cm²): (a) 32.4 J (b) 32.4 mJ (c) 26.4 J (d) 26.4 mJ
Solution. (a) U = (1/2) × Y × (strain)² × volume = (1/2) × Y(αΔθ)² × A × L [thermal strain = l/L = αΔθ] = (1/2) × (2 × 1011) × (18 × 10−6 × 100)² × 1 × 10−4 × 1 = 324 × 10−1 = 32.4 J.
Teacher's Note: Blocked expansion gives strain αΔθ; energy is (1/2)Y(strain)² times volume.
Exam Note: Volume is A × L = 10−4 m³.
Question 46. Which of the following cases will have the greatest strain energy (F is the stretching force, A is the area of cross section and s is the strain)? (a) F = 10 N, A = 1 cm², s = 10−3 (b) F = 15 N, A = 2 cm², s = 10−3 (c) F = 10 N, A = (1/2) cm², s = 10−4 (d) F = 5 N, A = 3 cm², s = 10−3
Solution. (b) Strain energy = (1/2) × stress × strain × volume = (1/2) × (F/A) × strain × AL = (1/2) × F × strain × L. For wire (a) U = (1/2) × 10 × 10−3 × L = 5 × 10−3 L; for wire (b) U = (1/2) × 15 × 10−3 × L = 7.5 × 10−3 L; for wire (c) U = (1/2) × 10 × 10−4 × L = 0.5 × 10−3 L; for wire (d) U = (1/2) × 5 × 10−3 = 2.5 × 10−3 L. For a given length, wire (b) will have the greatest strain energy.
Teacher's Note: Area cancels: U = (1/2)·F·s·L, so compare the products F × s for equal length.
Exam Note: Assume equal lengths.
Free study material for Physics
Download Pradeep's KL Gogia Solutions for Class 11 Math PDF
Chapter-wise Pradeep's KL Gogia Solutions: Pradeep's KL Gogia Solutions Physics Chapter 3 Elasticity Part 1
Review detailed solutions for Class 11 Mathematics. The Pradeep's KL Gogia Solutions Physics Chapter 3 Elasticity Part 1 PDF provides comprehensive answers mapped to standard Pradeep's KL Gogia Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Step-by-Step Mathematical Explanations
Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.
Additional Study Materials for 2026
Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.
FAQs
They are chapter-wise solved questions from the Pradeep's KL Gogia book for Class 11 Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.