Download Class 10 Science Textbook Solutions: Chapter 13 Magnetic Effects Of Electric Current
Review structured textbook solutions for Class 10 Science Chapter 13 Magnetic Effects Of Electric Current prepared by . Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Access Textbook Answers and Solutions
Navigate directly to the solved Science textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Check Point 01
Question 1. What is the SI unit of magnetic field?
Solution.
The SI unit of magnetic field is Tesla denoted by T.
1 T is defined as the magnetic field in which particle of charge 1 Coulomb moving perpendicularly to a magnetic field at a speed of 1 m/s experiences the force of 1N.
Teacher's Note: Magnetic field strength is measured in tesla, named after Nikola Tesla; one tesla equals one newton per ampere-metre.
Exam Note: SI unit of magnetic field: tesla (T).
Question 2. What is the direction of magnetic field inside a bar magnet?
Solution.
The Magnetic field lines always begin from the North ‘N’ pole of the magnet and ends on south ‘S’ pole of the magnet.
However inside the magnet the direction of magnetic field lines is from ‘S’ pole to ‘N’ pole.
The figure below illustrates the magnetic field lines direction inside the bar magnet.
Teacher's Note: Outside a bar magnet field lines run from north to south; inside the magnet they continue from south to north.
Exam Note: Closed loops: N to S outside, S to N inside.
Question 3. Why can’t two field lines intersect each other?
Solution.
The two magnetic field lines never intersect each other because if they intersect than two tangents can be drawn from the point of intersection of the field lines which will give the two directions of the field from the same point (shown in figure below) which is impossible because the resultant force on a pole (north/south) at any point can only be in one direction. Hence the field lines never intersect.
Teacher's Note: A field line gives the field direction at each point; two lines crossing would give two directions at one point.
Exam Note: Field lines never intersect: one direction at each point.
Question 4. How can we predict about the strength of a magnetic field in a space?
Solution.
Following are the ways by which we can determine the magnetic field in a space.
1. Magnetic field can be written in terms of vector potential an by determining the potential we can find the strength.
2. By using the magnetometer we can measure the strength of the magnetic field.
Teacher's Note: Strength of a magnetic field can be measured with a magnetometer; closer field lines indicate a stronger field.
Exam Note: Closer field lines mean stronger field; measure with magnetometer.
Question 5. Where is the magnetic field due to a straight current wire (i) Stronger (ii) Weaker?
Solution.
(i) Stronger = the magnetic field lines are stronger in the region around the wire and it decreases with the increase in the distance from the wire.
(ii) Weaker = the magnetic field lines are weaker in the region far away from the wire because as the distance from the wire increases the magnetic field intensity decreases. Figure below shows the field lines due to wire.
Teacher's Note: Field around a straight current wire forms concentric circles; strength decreases as distance from the wire increases.
Exam Note: Straight wire: field strongest near wire, weaker farther away.
Check Point 02
Question 1. What happens to the strength of the magnetic field if the number of turns is increased?
Solution.
The magnetic field is directly proportional to the number of turns in the magnet. Therefore on increasing the number of turns the magnetic field will increase because, with addition of each turn there will be an increase in number of charge carriers that contribute to the field at a point.
Teacher's Note: A coil with more turns carries more current loops, so each turn adds to the magnetic field.
Exam Note: More turns, stronger magnetic field.
Question 2. What is the nature of magnetic field inside a solenoid?
Solution.
When current is passed through a solenoid, the magnetic fields act almost like that of a bar magnet. One end acts as the magnetic north pole, and the other end acts as the magnetic South Pole.
The magnetic field lines inside the solenoid are in parallel straight lines, which indicate that the magnetic field is same at all points inside the solenoid. However, the field lines outside the solenoid travels from one pole to the other. Figure below shows the magnetic field lines inside the solenoid.
Teacher's Note: Inside a current-carrying solenoid the field is uniform, with parallel straight field lines, like a bar magnet's field.
Exam Note: Solenoid: uniform field inside, bar-magnet pattern outside.
Question 3. A circular loop carrying a current is placed on a horizontal surface (current is in the clockwise direction). What is the direction of its magnetic field at the centre? What is the direction of the magnetic field at a point outside the surface of the loop?
Solution.
The direction of the current in the circular current carrying coil is given by the Thumb rule.
Direction of magnetic field at centre for the loop carrying current in clockwise direction is perpendicular to the plane and is inward (going into the plane) which is south pole shown in the figure below.
Teacher's Note: Clock rule: a face with clockwise current acts as a south pole; the field is directed into that face.
Exam Note: Clockwise current: field into the plane at the centre.
Question 4. What is difference in the pattern of magnetic field due to a circular loop and inside a solenoid?
Solution.
| Circular Loop | Solenoid |
|---|---|
| 1. Induced North Pole and South Pole are close to each other. | Induced north pole and south pole are some distance apart from each other due to many turns of wire. |
| 2. Magnetic field is present inside circular loop. | A strong, uniform magnetic field is present inside the solenoid, while the field outside is very weak. |
Teacher's Note: A loop gives a field that is strong only near its wire; a solenoid gives a strong uniform field inside.
Exam Note: Loop: concentric circles; solenoid: strong uniform field inside.
Question 5. What is the principle of an electromagnet?
Solution.
An electromagnet works on the magnetic effect of electric current: when current flows through a coil wound on a soft iron core, the core becomes a magnet.
An electromagnet is a device used to generate a magnetic field with the help of an electric current.
Under the influence of electric current, all atoms are reoriented to start pointing in the same direction. All these individual magnetic fields together create a strong magnetic field. As the current flow increases, this degree of reorientation also increases, resulting in a stronger magnetic field.
Once all the particles are reoriented perfectly in the same direction, increasing current flow will not affect the magnetic field produced. At this point, the magnet is said to be saturated.
Teacher's Note: Electromagnet works on the magnetic effect of current: a current in a coil magnetises a soft iron core.
Exam Note: Electromagnet: current in a coil on soft iron.
Check Point 03
Question 1. When is the force on a current carrying wire.
(i) Maximum (ii) Minimum
Solution.
(i) Maximum: When the direction of current is perpendicular to the direction of the magnetic field the force on wire is maximum.
(ii) Minimum: When the direction of current is parallel to the direction of the magnetic field the force on wire is minimum.
Teacher's Note: Force on a current-carrying wire depends on the angle between the current and the field; it is zero when parallel.
Exam Note: Maximum force at 90 degrees; zero when parallel.
Question 2. Name the rule that gives the direction of force on a current carrying conductor placed perpendicular to the magnetic field.
Solution.
Fleming’s Left hand rule gives the direction of force on a current carrying conductor placed perpendicular to the magnetic field.
Fleming’s Left hand rule: According to this rule, stretch the thumb, fore-finger and middle finger of left hand such that they are mutually perpendicular. If the fore-finger points in the direction of the magnetic field, the middle finger points in the direction of flow of current, then the thumb points in the direction of motion i.e., force acting on the conductor.
Figure below illustrates it.
Teacher's Note: Fleming's left-hand rule gives the direction of force on a current-carrying conductor in a magnetic field.
Exam Note: Left hand: forefinger field, middle finger current, thumb force.
Question 3. The direction of magnetic field at a place is coming out of the paper. A wire whose direction of current flow is as shown in the figure is placed there. In which direction is the force due to the magnetic field experienced by the wire?
Solution.
According to Fleming’s left hand rule, the forefinger points in the direction of the magnetic field (out of the paper), the middle finger points in the direction of the current (towards north-east), and then the thumb gives the direction of the force on the conductor, which is perpendicular to both. Therefore the direction of the force on the conductor is south-east.
Teacher's Note: Force on a current-carrying wire is perpendicular to both field and current, as given by Fleming's left-hand rule.
Exam Note: Force is perpendicular to both field and current.
Question 4. What is the cause of magnetic field inside a human body?
Solution.
The magnetic field in the human body comes from the metabolism within the cells in the body.
In human body small electric current travel along the nerve cells due to ions, same way as electricity flows through the wire. This current produces very weak magnetic field in the human body. Heart and Brain are the two main organs in the human body where this field is significant.
Teacher's Note: Nerve cells carry tiny ionic currents, and these currents produce very weak magnetic fields, mostly from heart and brain.
Exam Note: Body field comes from tiny currents in nerve cells.
Question 5. What is an electric motor?
Solution.
Electric motor is the device in which electrical energy is converted into the mechanical energy.
Teacher's Note: A motor turns electrical energy into mechanical energy using the force on a current-carrying coil in a magnetic field.
Exam Note: Motor: electrical to mechanical energy; split ring reverses current.
Check Point 04
Question 1. What is electromagnetic induction?
Solution.
Electromagnetic Induction is a current produced because of voltage production (electromotive force) due to a changing magnetic field. This either happens when a conductor is placed in a moving magnetic field (when using AC power source) or when a conductor is constantly moving in a stationary magnetic field.
This phenomenon was discovered by Michael Faraday. Figure below shows the setup for electromagnetic induction.
Teacher's Note: Changing magnetic flux through a coil induces an emf and a current in the coil.
Exam Note: Induction needs changing magnetic field; discovered by Faraday.
Question 2. Where is Fleming’s right hand rule used?
Solution.
It can be used to determine the direction of current in a generator's windings. It can also be used to show the direction of induced current when a conductor attached to a circuit moves in a magnetic field.
Fleming right hand rule is mainly applicable for the electric generator. Figure below shows how to determine the direction of current using Fleming right hand rule.
Teacher's Note: Fleming's right-hand rule gives the direction of induced current in a conductor moving in a magnetic field.
Exam Note: Right hand: forefinger field, thumb motion, middle finger current.
Question 3. Differentiate between the time varying and constant currents.
Solution.
| Time Varying current | Constant current |
|---|---|
| 1. It is the current of magnitude varying with time | It is the current of constant magnitude. |
| 2. It reverses its direction while flowing in a circuit. | It flows in one direction in the circuit. |
| 3. The frequency of this current is 50Hz or 60Hz depending upon the country | The frequency of constant current is zero. |
| 4. Safe to transfer over longer city distances and can provide more power | Voltage of constant current cannot travel very far until it begins to lose energy. |
Teacher's Note: Time-varying current changes with time, usually reversing; constant current flows steadily in one direction.
Exam Note: AC reverses and varies; DC is steady with zero frequency.
Question 4. What is an electric generator?
Solution.
Electric generator is the device which converts the mechanical energy into the electrical energy.
It works on the Faraday’s law of the Electromagnetic Induction which says that whenever a conductor is placed in a varying magnetic field, EMF is induced and this induced EMF is equal to the rate of change of flux.
Electric generators are of two types A.C generator and D.C generator. Figure below shows the A.C generator.
Teacher's Note: A generator turns a coil in a magnetic field, inducing an emf by electromagnetic induction.
Exam Note: Generator: mechanical to electrical energy, by induction.
Question 5. Write down the differences between AC and DC generators.
Solution.
| AC Generators | DC Generators |
|---|---|
| 1. AC generator is a mechanical device which converts mechanical energy into AC electrical power. | DC generator is a mechanical device which converts mechanical energy into DC electrical power. |
| 2. In an AC generator, the electrical current reverses direction periodically. | In a DC generator, the electrical current flows only in one direction. |
| 3. AC generator does not have commutators. | DC generators have commutators to make the current flow in one direction only. |
| 4. AC generators have slip-rings. | DC generators have split-ring commutators. |
Teacher's Note: AC generators use slip rings; DC generators use a split-ring commutator to keep current in one direction.
Exam Note: AC: slip rings; DC: split-ring commutator.
Check Point 05
Question 1. At what potential and frequency are the domestic electric circuits operated?
Solution.
In our country the potential difference is 220 V and the frequency is 50 Hz. It is different for the different countries. And the potential difference is between the live wire and the neutral wire.
Teacher's Note: Household supply in India is about 220 V and 50 Hz, applied between live and neutral wires.
Exam Note: India: 220 V, 50 Hz between live and neutral.
Question 2. Usually, three insulated wires of different colours are used in an electrical appliance. Identify the three colours.
Solution.
Electrical wires follow standard color coding that helps classify each wire function in the circuit. In India wires are RGB mode i.e. Red- Green- Black. Each of these RGB wire have different functions.
1. RED = Red wire signifies the phase in electric circuit. It is the live wire, which must never be connected to the black (neutral) wire.
2. BLACK = Black wires signifies neutral wire in electric circuit. The neutral wire is connected to neutral bus bar inside an electric panel.
3. GREEN = Green wire stands for grounding/ Earthing in electric circuit. A green wire should be connected to a green wire only (no other wire).
Teacher's Note: Household wiring uses a colour code: red for live, black for neutral and green for the earth wire.
Exam Note: Red live, black neutral, green earth.
Question 3. Why should a fuse wire of defined rating not be replaced by one with a larger rating?
Solution.
Fuse is used for protecting appliances due to short-circuiting or overloading. The fuse is rated for a certain maximum current and blows off when a current more than the rated value flows through it.
If a fuse is replaced by one with larger ratings, the appliances may get damaged while the protecting fuse does not burn off. This practice of using fuse of improper rating should always be avoided.
Teacher's Note: A fuse melts when current exceeds its rating; a higher-rated fuse would not protect the appliance.
Exam Note: Higher-rated fuse fails to protect; never replace with larger rating.
Question 4. What does it mean when we say that a circuit is short circuited?
Solution.
A short circuit is an electrical circuit that allows a current to travel along an unintended path with no or a very low resistance. This results in an excessive amount of current flowing into the circuit A common type of short circuit occurs when the positive and negative terminals of a battery are connected with a low-resistance conductor, like a wire. With a low resistance in the connection, a high current will flow, causing the delivery of a large amount of energy in a short period of time
Teacher's Note: Short circuit means current takes a very low-resistance path, producing a very large current and heating.
Exam Note: Short circuit: very low resistance path, huge current.
Question 5. What is overloading of an electric circuit?
Solution.
The current in a circuit depends on the rating of the appliances connected to it. The choice of wires depends upon the maximum current estimated to pass through them. If the total power rating of the appliances exceeds this permitted limit, they tend to draw a large current. This is known as overloading, because of which excessive heating takes place.
Overloading occurs when too many appliances are connected in a single socket or when there is an accidental hike in the supply voltage.
Teacher's Note: Overloading means drawing more current than the circuit can safely carry, causing excessive heating.
Exam Note: Overloading: too many appliances, current exceeds safe limit.
Chapter Exercise
Question 1. What name is given to the device which automatically cut-off the electrical supply during short circuiting in household wiring?
Solution.
A fuse is an electrical safety device that is used to cut electrical supply during short circuit. It is a metal wire or strip that melts when too much current flows through it, thereby interrupting the current.
Teacher's Note: A fuse is a thin wire of low melting point that melts and breaks the circuit during excess current.
Exam Note: Fuse: breaks circuit in short circuit or overload.
Question 2. In which wire in an AC housing circuit, is the switch introduced to operate the light?
Solution.
The switch is introduced in the live wire. When the switch is off, the appliance is cut off from the live wire and cannot give an electric shock. The neutral wire completes the circuit, and the earth wire is connected to the metallic body of the appliance to prevent electric shock.
Teacher's Note: A switch is placed in the live wire so the appliance is isolated from live supply when switched off.
Exam Note: Switch goes in the live wire.
Question 3. The diagram shows a coil of wire wound on a soft iron core forming an electromagnet. A current is passed through the coil in the direction indicated by the arrows. Mark the N and S-poles produced in the iron core.
Solution.
By using the clock face rule which states that “When an observer, looking at the face of the coil, finds the current to be flowing in the anti-clockwise direction, then the face of the coil will behave like the North Pole. While if the current is in the clockwise direction, the face of the coil will behave like South Pole.”
South Pole: A
North Pole: B
Teacher's Note: Clock rule: the end where current appears anticlockwise is a north pole; clockwise is a south pole.
Exam Note: Anticlockwise face is north; clockwise face is south.
Question 4. Why is an alternating current considered to be advantageous over direct current for long range transmission of electric energy.
Solution.
Alternating current can be transmitted over the long distances with very little loss of energy. Also alternating voltage can be stepped up and stepped down using transformer.
Teacher's Note: AC voltage can be stepped up or down by transformers, so power can be sent far with little loss.
Exam Note: AC: transformers allow high-voltage transmission with low loss.
Question 5. A magnet AB is broken into two pieces. Point out the polarity of A, B, C and D.
Solution.
A magnet AB is broken into two pieces, AC and DB, as shown in the figure below.
If A is the north pole of the original magnet (so that B is its south pole), then the polarity of A is north and of C is south; the polarity of D is north and of B is south.
Because single poles of a magnet do not exist, when the magnet is broken the two poles (north and south) are created immediately at the broken ends, and each piece becomes a complete magnet.
Teacher's Note: Breaking a magnet always gives smaller magnets, each with its own north and south poles.
Exam Note: Isolated magnetic poles do not exist; every piece has two poles.
Question 6. The diagram shows a beam of electrons about to enter a magnetic field. The direction of the field is into the page. What will be the direction of the deflection, if any beam passes through the field?
Solution.
The electrons move from left to right, so the direction of conventional current is from right to left, and the magnetic field is into the page.
According to Fleming’s left hand rule the force is perpendicular to both the current and the field, and it acts towards the bottom of the page. So the electron beam deflects towards the bottom of the page, as shown in the figure below.
Teacher's Note: Moving electrons in a magnetic field experience a force perpendicular to both velocity and field.
Exam Note: Electron current is opposite to electron motion.
Question 7. A small valued resistance XY is connected across the ends of a coil. Predict the direction of induced current in the resistance XY when.
(ii) South pole of a magnet moves away from end A of the coil.
Solution.
(i) According to Lenz’s law, the induced emf opposes the change that produces it. To oppose the approaching south pole of the magnet, a south pole is developed at end A of the coil. Thus the current will flow in the clockwise direction when viewed from end A, the magnet's side, as shown in the figure below.
(ii) According to Lenz’s law, the induced emf opposes the change that produces it. To oppose the south pole going away, a north pole is developed at end A of the coil so that the south pole of the magnet is attracted and does not go away. Thus the current will flow in the anticlockwise direction when viewed from end A, as shown in the figure below.
Teacher's Note: By Lenz's law, induced current opposes the change producing it, so the coil end acts as a magnet pole.
Exam Note: Approaching pole: like pole forms; receding pole: opposite forms.
Question 8. A coil P is connected to a torch bulb and placed to another coil Q as shown in figure below:
(i) Bulb lights and (ii) bulb gets dimmer, if the coil P is moves upwards.
Solution.
(i) The bulb lights due to the mutual induction. The emf is produced in the conductor when the magnetic flux linked with the conductor changes. Due to this emf the bulb gets lighted.
(ii) When the coil P is move upwards the magnetic flux linked with the coil gets decreased due to which the induced emf gets decreased, hence the bulb gets dimmer.
Teacher's Note: Alternating current in coil Q produces changing flux through coil P, inducing an emf by mutual induction.
Exam Note: Mutual induction: changing flux induces emf in neighbouring coil.
Question 9. Three diagrams in the following figures show the magnetic field lines between the poles of the magnets. Identify the poles between A,B,C,D,E and F.
Solution.
(i) A is North Pole and B is South Pole because magnetic field lines originate from North Pole and ends at South Pole.
(ii) C and D are South Pole because the magnetic field lines end at the South Pole and same type of poles repel each other.
(iii) E and F are South Pole because the magnetic field lines end at the South Pole and same type of poles repel each other.
Teacher's Note: Field lines leave a north pole and enter a south pole; similar poles make lines bend away from each other.
Exam Note: Lines leave N, enter S; like poles repel.
Question 10. Why does a magnetic compass needle pointing North and South in the absence of a nearby magnet gets deflected when a bar magnet or a current carrying loop is brought near it. Describe some salient features of magnetic field lines concept.
Solution.
A magnetic compass needle pointing North and South shows deflection when a bar magnet or a current carrying loop is brought near it. This happens because the magnetic fields of the compass needle and the bar magnet (or current carrying loop) interact with each other.
Salient features of magnetic field lines:- a. Outside a magnet, magnetic field lines follow the direction from the North Pole to the South Pole.
b. Magnetic field lines are closed curves.
c. Magnetic field lines do not cross one another.
d. Closer the field lines; stronger is the magnetic field and vice-versa is also true.
e. Magnetic field lines are closer near the poles; which shows greater strength of magnetic field near the poles.
Teacher's Note: A compass needle is a small magnet, so a nearby magnetic field exerts torque on it.
Exam Note: Field lines: closed, never cross, closer means stronger.
Question 11. With the help of a labelled circuit diagram illustrate the pattern of field lines of the magnetic field around a long current carrying straight conducting wire. How is the right hand thumb rule useful to find direction of magnetic field associated with a current carrying conductor?
Solution.
The magnetic field lines around a straight conductor (straight wire) carrying current are concentric circles whose centers lie on the wire. Figure below shows the field lines.
Teacher's Note: Field lines around a straight current-carrying wire are concentric circles; right-hand thumb rule gives their direction.
Exam Note: Thumb along current; curled fingers show field direction.
Question 12. You are given the following current- time graphs from two different sources:
(i) Name the type of current in two cases.
(ii) Identify any one source for each type of these currents.
(iii) What is the frequency of current in case (b) in India?
(iv) Use above graphs to write two differences between the current in two cases.
Solution.
(i) The current in first case is the Direct current because it is constant with the time. The current in second case is the Alternating current because its direction and magnitude changes continuously with the time.
(ii) Source of direct current are solar cell, fuel cell etc.
Source of alternating current the electricity coming to our home.
(iii) The frequency of the Alternating current in India is 50 Hz.
(iv)
| Alternating current | Direct current |
|---|---|
| 1. The frequency of alternating current is 50Hz or 60Hz depending upon the country. | The frequency of direct current is Zero. |
| 2. It is the current of magnitude varying with time | It is the current of constant magnitude. |
Teacher's Note: Direct current is constant with time; alternating current changes direction and magnitude periodically; Indian mains frequency is 50 Hz.
Exam Note: DC constant; AC periodic; India 50 Hz.
Question 13.
(ii) Give one difference between the wires used in the element of an electric heater and in a fuse.
(iii) List two advantages of parallel connection over series connection.
Solution.
(i) Following are the errors in the circuit given above.
a) Fuse is incorrectly connected to the Neutral wire (N), it must be connected to the live wire (L).
b) Bulb B2 is not connected to the neutral wire; its lower terminal is wrongly connected to the earth wire (E).
c) Switch S2 is connected in the neutral wire, it must be connected in the live wire.
(ii) Element of electric heater has high melting point in order to stand high temperatures while element of fuse has low melting point.
(iii) 1. Each appliance will have an equal potential difference.
2. Each appliance will have a separate switch to ON/OFF the flow of the current.
Teacher's Note: Safe wiring puts fuse and switches in the live wire and connects every appliance between live and neutral.
Exam Note: Fuse and switch belong in live wire only.
Question 14. Overloading in an electric circuit causes fire. Many people are unaware of this fact. Amit, an intelligent student told people of his building about overloading. He told them various precautions to avoid it. Answer the following questions:
(i) What harm does overloading in the circuit cause?
(ii) What values are shown by Amit?
Solution.
(i) Overloading can lead to damage, poor performance and possible failure. There may be a risk of fire or damage to components. It can also lead to sparks, arcs or insulation failure. Current overload will cause things to heat up, and then possibly melt, set on fire, damage insulation or cause components to fail. Some components will be damaged by the excessive current without overheating.
(ii) Amit is very caring and worried towards his society and people. He is also quite aware and intelligent. He uses his knowledge of science for helping society which is the sole purpose of education.
Teacher's Note: Overloading overheats wires and insulation, which can cause fires, so awareness and precautions protect people.
Exam Note: Overloading: heating, insulation failure, fire risk.
Question 15. Rajat had gone to his aunt’s home in a foreign country, where domestic electric supply is DC. An electrician working in her kitchen was trying to locate the electric wiring in a particular wall for some electrical work but failed to do so. Electrician, then suggested the breaking of substantial position of wall to Rajat’s aunt.
But Rajat told his aunt that he could locate the position of current carrying wires in the kitchen without any breakage. He brought a small device from market and within ten minutes, located the position of all current carrying wires on wall of his aunt got very happy from him.
Read the above passage and answer the following questions:
(i) Which device was purchased by Rajat?
(ii) What was noticed by Rajat when he moved this device slowly over the current carrying wires embedded kitchen?
(iii) What values are shown by Rajat in this episode?
Solution.
(i) Rajat has purchased a Compass because it contains the magnet and in presence of the electric current the needle in it deflects which helps in detecting the current carrying wires.
(iii) Rajat is very aware and clever. He quickly brought the instrument to help his aunt this shows he is very helping and caring towards his aunt.
Teacher's Note: A compass needle deflects near a current-carrying wire, so it can detect hidden wires.
Exam Note: Compass deflection detects magnetic field of current.
Challengers
Question 1. Which of the following figures shows the correct magnetic field lines?
Figure: four patterns of iron filings: (a) a circular (ring-shaped) pattern; (b) lines bulging out in the middle and bunched together at the top and bottom; (c) lines running along and through a solenoid; (d) lines forming a rectangular closed frame with a small magnet (N, S) in its top side.
A. (a)
B. (b)
C. (c)
D. (d)
Solution.
In option A the magnetic field lines are circular and closed. But in option D the magnetic field lines are shown as square in shape, therefore it is incorrect. In options B and C the lines are not shown as closed circular curves.
Teacher's Note: Magnetic field lines are continuous closed curves; around a straight wire they form concentric circles.
Exam Note: Field lines are closed, smooth curves, never square.
Question 2.
Solution.
Since the key is taken out due to which there is no magnetic field due to wire. Hence only magnetic field of earth is present and the magnetic field lines of the earth are straight lines parallel to each other.
Hence the correct option is C.
Teacher's Note: With no current, only Earth's field acts, and its lines near a small region are straight and parallel.
Exam Note: Key open: only Earth's field, parallel straight lines.
Question 3. Three plotting compasses are placed near a solenoid carrying a current. How many of the compass needles will change direction, if the current through the solenoid is increased? (Ignore the effect of the earth’s magnetic field).
A. Only 1 compass needle
B. 2 compass needle
C. 3 compass needle
D. None of the above
Solution.
Increasing the current only increases the strength of the magnetic field of the solenoid; it does not change the direction of the field. Since the earth’s magnetic field is ignored, the direction of each compass needle, which is set by the solenoid’s field, remains the same. Hence no compass needle will change its direction (option D).
Teacher's Note: Increasing current strengthens a solenoid's field but does not change its direction.
Exam Note: Stronger current changes strength, not direction.
Question 4. A ship is to reach a place 8° south of west. In what direction should the ship be steered if declination at the place is 18° west?
A. West of magnetic north at angle 64° B. East of magnetic south at angle 64° C. West of magnetic south at angle 50° D. East of magnetic north at angle 18°
Solution.
Initially the ship is at 8° south of west. Applying the declination of 18° gives the actual direction. Now from north we get the direction of 90 − 18 − 8 = 90 − 26 = 64° west of north. Hence the correct option is A.
Teacher's Note: Declination is the angle between geographic north and magnetic north, used to correct compass bearings.
Exam Note: Apply declination to convert true to magnetic bearing.
Question 5. A rectangular loop carrying a current is situated near a long straight wire such that the wire is parallel to one of the sides of the loop and is in the plane of the loop. If a steady current its created in wire as shown in figure below, then the loop will.
Solution.
The side of the loop nearer to the long wire carries current in the same direction as the current in the wire, so it is attracted towards the wire. The side which is farther carries current in the opposite direction, so it is repelled.
F (attraction) > F (repulsion), because the nearer side is in a stronger magnetic field. Hence the loop moves towards the wire (option B).
Teacher's Note: Parallel currents attract and opposite currents repel; the nearer side feels the stronger force.
Exam Note: Parallel currents attract; nearer side dominates.
Question 6. Four metal rods are placed, in turn, inside a coil of copper wire,
The table below gives the results of the experiment. Which rod would be the most suitable to use for the case of a coil in a circuit breaker?
| Metal rod | Number of paper clips picked up when there is a current in the coil | Number of paper clips still attracted when the current is switched off |
|---|---|---|
| (a) | 1 | 0 |
| (b) | 20 | 2 |
| (c) | 35 | 0 |
| (d) | 35 | 30 |
A. (a)
B. (b)
C. (c)
D. (d)
Solution.
The core of solenoid must be of some soft type magnetic material which can be strongly magnetized but does not retain induced magnetism. Rod (c) picks up the most paper clips (35) and retains none (0) when the current is switched off. Hence the most suitable rod is (c).
Teacher's Note: Circuit breaker cores need soft magnetic material: strongly magnetised with current, demagnetised when current stops.
Exam Note: Soft iron core: strong magnet, retains nothing.
Question 7. A copper wire is held between the poles of a magnet.
The current in the wire can be reversed. The pole of the magnet can also be changed over. In how many of the four directions shown can the force act on the wire?
A. 1
B. 2
C. 3
D. 4
Solution.
The force on the wire due to the interaction of magnetic fields of the magnet and the current carrying wire can act only in upwards or downwards direction. Hence the force can act in 2 of the four directions shown (option B).
Teacher's Note: Force on a wire in a magnetic field is perpendicular to both wire and field.
Exam Note: Force is perpendicular to both current and field.
Free study material for Science
Class 10 Mathematics: All In One Solutions for All In One Solutions Class 10 Science Chapter 13 Magnetic Effects Of Electric Current
Chapter-wise All In One Solutions: All In One Solutions Class 10 Science Chapter 13 Magnetic Effects Of Electric Current
Review detailed solutions for Class 10 Mathematics. The All In One Solutions Class 10 Science Chapter 13 Magnetic Effects Of Electric Current PDF provides comprehensive answers mapped to standard All In One Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Detailed Calculation Guides for Class 10
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Next Steps in Your Mathematics Revision
In addition to these All In One Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the book for Class 10 Science. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.