LA Sena Solutions Physics Chapter 4 Direct Current

Download JEE Physics LA Sena Textbook Solutions: Chapter 04 Direct Current

Explore reliable textbook solutions for Chapter 04 Direct Current tailored for JEE learners using LA Sena methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.

Access LA Sena Textbook Answers and Solutions

View or download the dedicated Chapter 04 Direct Current solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Physics.

Chapter 4 Direct Current - Problems 4.1 to 4.42

Problems and Answers

Question 4.1. Two conductors, 1-3-5 and 2-4-6, connected points with equal potentials on the resistors Ra and Rb, so that no current flows through either of them. Will there be currents flowing through them and through the 3-4 section if the key K is closed? Will this lead to a change in the reading of the ammeter? (Fig. 4.1: resistors Ra (top) and Rb (bottom) are joined by the conductors 1-3-5 and 2-4-6; key K connects 3 and 4; the ammeter is in the external lead.)

Solution. The two conductors 1-3-5 and 2-4-6 have different potentials, so when key K is closed a current will flow from 3 to 4, while the currents through the resistors will differ: from 1 to 3, from 5 to 3, from 4 to 2 and from 4 to 6. The closing of the key leads to an increase in the current flowing through the ammeter. If the resistances of the conductors 1-3-5, 2-4-6 and 3-4 are extremely low, then the sections 1-2 and 5-6 will be shorted for all practical purposes.

Teacher's Note: Closing K joins points of unequal potential, so new current paths appear and the total resistance falls.

Exam Note: State the effect on the ammeter reading with a reason.

Question 4.2. How will the reading of the ammeter change if the key K is closed? (Fig. 4.2: resistors R and 2R in the upper branch, 2R and R in the lower branch, key K joining the midpoints, ammeter in the external lead.)

Solution. Prior to closing the key, the circuit consists of two resistors connected in parallel (the resistance of each resistor being 3R). This means that the total resistance of the circuit is 1.5R. After the key has been closed, the circuit consists of two sections in series, each of which has two resistors connected in parallel. The resistance R' of each section is given by the formula 1/R' = 1/R + 1/2R and is equal to 2R/3. The resistance of the entire circuit is 4R/3. The current measured by the ammeter is higher than that measured prior to closing the key.

Teacher's Note: Compare total resistance before (1.5R) and after (4R/3) closing the key; lower resistance means larger current.

Exam Note: Show both resistances, then compare currents.

Question 4.3. A voltage U0 is applied to a potentiometer whose sliding contact is exactly in the middle. A voltmeter V is connected between the sliding contact and one fixed end of the potentiometer. It is assumed that the resistance of the voltmeter is not very high if compared with the resistance of the potentiometer. What voltage will the voltmeter show: higher than, less than, or equal to U0/2?

Solution. If R is the resistance of the whole potentiometer and RV is the resistance of the voltmeter, the total resistance of section ab of the potentiometer is Rab = RV(R/2)/(RV + R/2) = R/[2(1 + R/2RV)] < R/2. The resistance of section bc is equal to R/2. The voltage applied to the potentiometer will not be distributed evenly. Since the resistance of ab is less than that of bc, the voltage applied to the first section is lower than that applied to the second. The higher the resistance of the voltmeter, the closer the readings of the voltmeter are to one-half of the applied voltage.

Teacher's Note: A voltmeter of finite resistance across half the potentiometer lowers that half's resistance, so it reads below U0/2.

Exam Note: Answer: less than U0/2, because of loading.

Question 4.4. A "black box" is an electric unit with four terminals, 1, 2, 3 and 4, and an unknown internal structure. The box shown in Figure (a) and (b) possesses the following properties: if a constant voltage of 220 V is applied to terminals 1 and 2, a voltage of 127 V appears across terminals 3 and 4 (Figure (a)), while if a voltage of 127 V is applied to terminals 3 and 4, the same voltage of 127 V appears across terminals 1 and 2 (Figure (b)). What is inside the "black box"? The formulation of the problem is quite meaningful if the voltages are measured by electrostatic voltmeters, which do not consume electric current. If voltmeters of the magnetoelectric, thermal, or electromagnetic type are employed, the voltages across the "out" terminals of the "black box" may somewhat differ from the ones indicated in Figures (a) and (b).

Solution. Since the voltage applied to the "black box" is supplied by a DC source, it is natural to assume that there are only resistances inside the "box". The simplest way to lower voltage is to use a potentiometer (see the figure accompanying the answer). However, there is not a single circuit employing only resistances that can raise voltage. As the figure accompanying the answer demonstrates, from the voltage applied to terminals 1 and 2 one can always "take" a certain fraction, e.g. 127 V, while the 127 V applied to terminals 3 and 4 will yield the same 127 V on terminals 1 and 2. The remark (made in the problem) that concerns the role of the measuring device is important since a voltmeter, which always has a finite resistance, redistributes the resistances in the circuit and, hence, changes the voltages (see Problem 4.3).
(Figure in the book: a potentiometer across 1-2 with terminal 3 taken from a sliding contact at the 127 V point and terminal 4 joined to terminal 2, drawn for both connections (a) and (b).)

Teacher's Note: Resistor networks only divide voltage, so the box is a potentiometer tapped at 127 V; voltmeter loading explains deviations.

Exam Note: Explain why resistors alone cannot step voltage up.

Question 4.5. Two potentiometers are connected in series, and their sliding contacts are connected electrically, too. In one potentiometer the sliding contact remains fixed at the midpoint. How will the reading of the ammeter vary as the sliding contact of the second potentiometer is moved from one end of the potentiometer to the other? (Fig. 4.5)

Solution. Let us assume, for the sake of simplicity, that the resistances of the two potentiometers are the same. When the sliding contact of each potentiometer is in the middle, the total resistance of the circuit is R0/2, where R0 is the resistance of each potentiometer. If the sliding contact of the second potentiometer is in the extreme (left or right) position, we have two resistances, R0 and R0/2, connected in parallel (assuming that the wires have no resistance), so that the total resistance is R = R0/3. The reading of the ammeter proves to be greater than when the sliding contact of the second potentiometer was in the middle position by a factor of 1.5. Thus, when the sliding contact of the second potentiometer is moved from one extreme position to the other, the readings of the ammeter pass through a minimum.

Teacher's Note: Find the circuit resistance at the middle (R0/2) and at an end (R0/3); current is smallest where resistance is largest.

Exam Note: Answer: current passes through a minimum, 1.5 times smaller at middle.

Question 4.6. A constant voltage U0 is applied to a potentiometer of resistance R connected to an ammeter. A constant resistor r is connected to the sliding contact of the potentiometer and the fixed end of the potentiometer (after the current). How will the reading of the ammeter vary as the sliding contact is moved from one end of the potentiometer to the other? The resistance of the ammeter is assumed to be negligible. (Fig. 4.6)

Solution. If x is the resistance of the potentiometer between point a and the sliding contact, the total resistance between a and the sliding contact is rx/(r + x), while the resistance of the entire circuit is R − x + rx/(r + x). The current supplied by the DC source is I = U0/[R − x + rx/(r + x)]. The potential difference between the sliding contact and point a is U = U0rx/[(R − x)(r + x) + rx] = U0rx/(Rx − x2 + Rr). The current passing through the ammeter is Ia = U0r/(Rx − x2 + Rr) (4.6.1). To find the extremum, we take the derivative dIa/dx = U0r[(−R + 2x)/(Rx − x2 + Rr)2] (4.6.2). Nullifying (4.6.2) yields x = R/2 (4.6.3). If we substitute (4.6.3) into (4.6.1) we find the minimal current: Imin = U0r/[R(r + R/4)]. Thus, as the sliding contact is moved, the current through the ammeter passes through a minimum, and the smaller the r the deeper the minimum. At x = 0 and x = R, a current of Imax = U0/R passes through the ammeter. The ratio of Imin to Imax is printed in the book as (r/R)(1 + r/R)−1. Corrected: from the two currents above, Imin/Imax = r/(r + R/4) = (4r/R)/(1 + 4r/R); the printed form would give 0.5 for r = R, whereas the book's own curve shows 0.8. The Ia/Imax vs. x/R curves for several values of r/R are shown in the figure accompanying the answer (U-shaped curves, equal to 1 at both ends and lowest at x/R = 0.5; deeper for smaller r/R, for r/R = 1, 0.5, 0.2, 0.1).

Teacher's Note: Write ammeter current as a function of x, set dI/dx = 0; the minimum sits at x = R/2.

Exam Note: Show derivative step; state minimum at the midpoint.

Question 4.7. To measure a small emf (of, say, a galvanic cell or a thermocouple) the so-called balancing method is employed. The circuit diagram of this method is shown in the figure. Here ℰx is the sought emf, ℰ is the source of current whose emf is much higher than ℰx, G is a galvanometer with the zero in the middle of the scale, A is an ammeter, and R is the resistance box. How should one operate this circuit so as to ensure an accuracy in measuring ℰx that is determined by the precision of the measuring devices? (Fig. 4.7)

Solution. The exact value of ℰx can be determined if one measures exactly the potential difference between points a and b provided that the current passing through the source in question is zero. This can be achieved by selecting a proper ratio of resistances between points a and b and points b and c using the resistance box. Knowing the resistance R between points a and b and the current I, measured by the ammeter, we find the sought emf: ℰx = IR.

Teacher's Note: Adjust the resistance box for zero galvanometer reading; the unknown cell then carries no current, so its emf equals IR.

Exam Note: Zero galvanometer deflection means ℰx = IR.

Question 4.8. Two resistors with resistances R1 and R2 are connected in series, and so are two capacitors with capacitances C1 and C2. The two systems are connected in parallel and an external voltage is applied to the new system (see the figure accompanying the problem). What must be the relationship between R1, R2, C1 and C2 for the potential difference between the points a and b to be zero? (Fig. 4.8)

Solution. Since the currents in the resistors R1 and R2 are the same, we can write UAa/R1 = UaB/R2. The charges on capacitors connected in series are the same, which means that UAbC1 = UbBC2. Since UAa/UaB = R1/R2, UAb/UbB = C2/C1, UAa = UAb, UaB = UbB, we have R1/R2 = C2/C1. The resistances and capacitances are in inverse ratio. Just as in Problem 3.27, where a DC source generates a potential difference between points A and B, the solution holds true only if the (active) resistances of the capacitors are infinitely large.

Teacher's Note: Equal potential at a and b means the resistor divider ratio equals the capacitor divider ratio, inverse to capacitance.

Exam Note: Final relation: R1/R2 = C2/C1.

Question 4.9. All the resistances and emf's shown in the figure accompanying the problem are assumed known. How many values of current can exist for such a circuit? How many equations for finding these values must we construct on the basis of Kirchhoff's first law and how many must we construct on the basis of Kirchhoff's second law? (Fig. 4.9)

Solution. The current remains unchanged on the entire section from one junction to another. A junction is a point in a circuit where more than three conductors meet. There are seven such sections in the figure accompanying the problem. If there are n junctions in a circuit, then Kirchhoff's first law yields n − 1 independent equations. There are four junctions in the circuit in question (1, 4, 5 and 7). Thus, to determine seven currents we are lacking four equations, which Kirchhoff's second law will yield. The simplest way to employ Kirchhoff's second law is to use loops that do not overlap, namely 1-2-3-4-1, 1-4-5-1, 1-5-7-1, and 5-6-7-5.

Teacher's Note: Count branches (7) and junctions (4): first law gives n − 1 = 3 equations, second law the remaining 4.

Exam Note: Answer: 7 currents; 3 junction and 4 loop equations.

Question 4.10. Twelve conductors are connected in such a way that they form a cube, and an emf source is connected into an edge of the cube. All the resistances and the emf's are known. There are eight junctions (eight vertices of the cube) and six loops (six faces of the cube) in the circuit. Construct the equations for determining all the currents in the circuit. (Fig. 4.10)

Solution. There are eight junctions in the circuit. Since Kirchhoff's first law yields only n − 1 independent equations, for n junctions, we have seven such equations. If the circuit is transformed onto a plane (see the figure accompanying the answer: a square within a square with the source on the edge 2-3 side), there are five nonoverlapping loops, while the loop 1-4-8-5-1 overlaps all other loops and therefore can be obtained from these.

Teacher's Note: Use n − 1 = 7 junction equations plus five independent loops of the planar drawing; the sixth is dependent.

Exam Note: Answer: 7 junction plus 5 loop equations.

Question 4.11. A source of electric current with an emf ℰ0 and an internal resistance r is connected to an external circuit with a resistance R. What must be the relationship between r and R for the power output in the external circuit to be maximal? What is the efficiency of the current source in this case, provided that the power output in the external circuit is assumed to be the useful output?

Solution. The current flowing in the circuit is I = ℰ/(R + r). The power output in the external circuit is P = I2R = ℰ2R/(R + r)2. The maximal power output can be found from the condition dP/dR = 0, or dP/dR = ℰ2[(R + r)2 − 2(R + r)R]/(R + r)4 = 0, whence R = r. The fact that the resistances are equal means that the power outputs must be equal, too: I2r = I2R. Hence, the efficiency is equal to 0.5.

Teacher's Note: Differentiate P = ℰ2R/(R + r)2; maximum at R = r, where half the source power is wasted.

Exam Note: Answer: R = r, efficiency 50%.

Question 4.12. In two circuits, each of which contains a DC source and an external resistance, the maximal currents are the same, while the maximum power output in the external resistance of one circuit is twice that in the other. In what parameters do these circuits differ?

Solution. The current is maximal when the circuit is shorted, or when the external resistance is zero: Im = ℰ/r. Thus, in both cases the ratio of the emf to the internal resistance is the same. Maximal useful power output (the power output of the external resistance) is achieved when the external resistance is made equal to the internal resistance (see the answer to Problem 4.11), that is, when the current is one-half the maximal current. This power output is P = ℰ2/4R = ℰ2/4r. Since the ratio ℰ/r is the same in both cases, a double useful power output is achieved at a double electromotive force (for equal currents). Note that the internal resistance of the DC source must also be doubled if we want the ratio to remain unchanged.

Teacher's Note: Maximum output ℰ2/4r with ℰ/r fixed means power is proportional to ℰ; doubling power needs doubled emf and r.

Exam Note: Answer: emf and internal resistance both doubled.

Question 4.13. A DC source is connected to a rheostat. When the sliding contact is x distant from either end of the rheostat (the length of the rheostat is set at unity), the power output in the rheostat is the same in both cases. Determine the internal resistance of the DC source if the resistance of the rheostat is R. (Fig. 4.13)

Solution. If in one position of the sliding contact the rheostat has a resistance R1 and in the other, a resistance R2, the current is ℰ/(R1 + r) in the first case and ℰ/(R2 + r) in the other. Correspondingly, the power output in the external circuit (the same in both cases) is P = ℰ2R1/(R1 + r)2 = ℰ2R2/(R2 + r)2. Dividing this expression by ℰ2 and solving for r, we find that r = √(R1R2). By hypothesis, in one case R1 = xR and in the other, R2 = (1 − x)R. Whence r = R√[x(1 − x)].

Teacher's Note: Equate P for R1 and R2; r is the geometric mean of the two resistances.

Exam Note: Answer: r = R√[x(1 − x)].

Question 4.14. How must a large number of galvanic cells, each having the same emf ℰ and the same internal resistance r, be connected so that in an external circuit whose resistance is R the power output is maximal?

Solution. The likely circuit, apparently, consists of a combination of cells connected in parallel and in series. There are two possibilities here: several parallel groups of cells connected in series or several in-series groups of cells connected in parallel. First, it can be shown that the two variants are equivalent. Indeed, in the first variant, the potentials at the points a1, a2, a3 etc. coincide, i.e. Ua1 = Ua2 = Ua3 = ...; the same is true of the potentials at the points b1, b2, b3, etc., i.e. Ub1 = Ub2 = Ub3 = .... This line of reasoning can be continued. The respective points can be interconnected, and the entire circuit will be transformed into the second variant. Suppose the overall number of cells is N. We connect these cells in such a manner that groups of n cells that form m = N/n parallel groups are connected in series. In this case the current in the external circuit is I = ℰn/(R + rn/m) = ℰNn/(RN + rn2). The power output in the external circuit is P = I2R = (ℰN)2R n2/(RN + rn2)2. To find the maximal value, we nullify the derivative of P with respect to n: dP/dn = [2ℰ2N2n/(RN + rn2)3](RN − rn2) = 0. Whence n = √(RN/r) (4.14.1). But this does not solve the problem completely. The number n should be one of the cofactors of N. To find a practical value of n, we must compare the power outputs for two values of n that are closest to the one given by (4.14.1), that is, one must be smaller than the calculated value and the other must be greater, and yet the two must be cofactors of N. Here is an example. Suppose N = 400, R = 16 Ω and r = 9 Ω. The calculated value is n = √(400 × 16/9) = 26.7. The closest cofactors of N are 25 and 40. In this example the greater power output is at n = 25. Thus, the circuit consists of 16 parallel groups of 25 cells connected in series in each group.
(Figure 4.14 in the book: m parallel rows of cells, each row n cells in series, all rows joined to the resistor R.)

Teacher's Note: Maximum power needs n = √(RN/r) cells per row; then compare outputs for the nearest factors of N.

Exam Note: Result n = √(RN/r); round to a factor of N.

Question 4.15. Can a circuit be constructed in which the displacement current in the capacitor remains practically constant over a definite time interval?

Solution. Since the displacement current is defined as Idis = S dD/dt, after performing certain manipulations we can write Idis = (ε0εS/l) dU/dt = dQ/dt, where Q is the charge on the capacitor. Thus, the displacement current may be made constant over a definite time interval if the capacitor is charged (or discharged) by a direct current. For this, in the circuit of the capacitor being charged we must have a device that restricts the current flowing through it within broad voltage limits (Figure (a)). A diode operating in the saturation mode may serve as such a device. For the case of a thermionic valve (or diode) the appropriate circuit is shown in Figure (b), while for the case of a semiconductor diode the circuit is shown in Figure (c). The diode is introduced into the circuit in the cut-off direction, and the voltage across the diode is Ud = ℰ0 − UC. As long as Ud remains within the saturation region, the current through the diode (and, hence, the charging current) remains constant. The displacement current remains constant in the process. After a certain time interval has elapsed (the lower the charging current the longer the interval), the charging current rapidly falls off to zero. The time dependence of the displacement current is illustrated schematically in Figure (d).
(Fig. 4.15: (a) battery, key K, capacitor C and a current limiter in series; (b) the same with a thermionic diode; (c) the same with a p-n diode; (d) Idis stays flat, then drops sharply to zero at later time t.)

Teacher's Note: A constant charging current gives constant dQ/dt; a saturated diode limits current, so yes, for a limited time.

Exam Note: Answer: yes, with a saturated diode as current limiter.

Question 4.16. A DC source with known emf ℰ is charging a capacitor C. After the charging process has been completed, the capacitor is disconnected from the DC source via a key K, and is connected to a resistor R, through which the capacitor discharges. The capacitance of the capacitor and the resistance of the resistor are selected in such a way that the charging process takes several minutes, so that the discharge current can be registered by a measuring device, G. The results of measurements are used to draw a rough curve on a diagram in which the time of discharge is laid off on the horizontal axis and the logarithm of the current, on the vertical axis. Determine the law by which the current varies and the curve representing the dependence of the logarithm of the current on the time of discharge. How can the curve help in determining the parameters of the discharge circuit, R and C? (Fig. 4.16)

Solution. At each moment of time the capacitor voltage is equal to the potential drop across the resistor; U = IR. Bearing in mind that U = Q/C and I = −dQ/dt (the minus sign shows that the capacitor's charge decreases), we get Q/C = −R dQ/dt, or dQ/Q = −(1/RC) dt (4.16.1). Integrating (4.16.1) from the initial charge Q0 to Q and from the initial moment t = 0 to time t, we get Q = Q0 exp(−t/RC) = U0C exp(−t/RC). Accordingly, the current varies with time as follows: I = I0 exp(−t/RC) (4.16.2), with I0 = U0/R. Taking logs, we can write (4.16.2) as ln I = ln I0 − (1/RC)t. Thus, the time dependence of ln I is represented by a straight line with a negative slope, whose absolute value is 1/RC. The resistance R determines the current at the first moment of discharge and the initial capacitor voltage, which is equal to the emf of the source. The value of R determined in this manner and the slope of the straight line fix the value of C.

Teacher's Note: Solve RC dQ/dt = −Q; ln I falls linearly with slope −1/RC and intercept ln(ℰ/R), giving R and then C.

Exam Note: Intercept gives R; slope gives C.

Question 4.17. A capacitor of capacitance C is charged to a potential difference U0 and is then discharged through a resistance R. The discharge current gradually decreases, with a straight line 1 corresponding to this process (see the figure accompanying the problem, where time is laid off on the horizontal axis and the logarithm of the current, on the vertical axis). Then one of the three parameters, U0, R, or C, is changed in such a manner that the ln I vs. t dependence is represented by the straight line 2. Which of the three parameters was changed and in what direction? (Fig. 4.17: lines 1 and 2 start from the same point on the ln I axis; line 2 is less steep than line 1.)

Solution. As shown in the answer to Problem 4.16, the discharge current varies with time as I = I0 exp(−t/RC), or ln I = ln I0 − (1/RC)t. Initially, i.e. at t = 0, both currents are the same (see the figure accompanying the problem). For a fixed capacitance C this is possible if the other two parameters, U and R, change simultaneously. Since by hypothesis only one parameter changes, we conclude that the capacitance C varies. The fact that the slope of the straight line representing the ln I vs. t dependence decreases means that the capacitance C increases.

Teacher's Note: Both lines share the initial current U0/R, so U0 and R are unchanged; only the slope 1/RC differs.

Exam Note: Answer: C was increased.

Question 4.18. A charged capacitor is discharged through a resistor two times. The time dependence of the logarithm of the discharge current obtained in the two experiments is represented by the two straight lines, 1 and 2, in the figure accompanying the problem. The experimental conditions differed only in one of the three parameters: the initial voltage of the capacitor U, the capacitance C, or the resistance R. Determine the parameter that was varied in these experiments and in which case this parameter is greater. (Fig. 4.18: two parallel straight lines, line 1 above line 2.)

Solution. The time variation of the current proceeds as follows: ln I = ln I0 − (1/RC)t. The fact that the two straight lines, 1 and 2, are parallel indicates that the product RC must be constant. Since by hypothesis the discharge processes differ only in the value of one parameter, both R and C remain constant. What is different is the initial capacitor voltage, and since for straight line 1 the initial current is higher than for straight line 2, so is the initial capacitor voltage.

Teacher's Note: Parallel lines mean equal slope 1/RC, so only U0 differs; the higher intercept belongs to the higher U0.

Exam Note: Answer: U0, greater in experiment 1.

Question 4.19. Prove that when a capacitor of capacitance C that has been charged to a potential difference U0 is discharged through a resistance R, the amount of heat liberated in the conductors is equal to the initial energy stored in the capacitor.

Solution. The current flowing through the resistor with resistance R will generate during a time interval dt the following amount of heat: dq = I2R dt. The time variation of the discharge current of the capacitor is I = I0 exp(−t/RC). Thus, dq = I02R exp(−2t/RC) dt. Integrating this expression with respect to t from t = 0 to t = ∞, we get q = I02R2C/2 (4.19.1) (Corrected: the book prints I02RC/2, which has the wrong dimensions; ∫I02R e−2t/RCdt = I02R·RC/2). At the first moment the discharge current is I0 = U0/R (4.19.2). Substituting (4.19.2) into (4.19.1), we obtain the initial energy stored in the charged capacitor: q = U02C/2.

Teacher's Note: Integrate I2R over all time: ∫0∞I02R e−2t/RCdt = CU02/2, independent of R.

Exam Note: Heat equals ½CU02, whatever R is.

Question 4.20. Prove that when a capacitor is charged through a resistor R from a DC source with an emf equal to ℰ half of the energy supplied by the source goes to the capacitor and half, to heating the resistor. (Fig. 4.20 is not separately shown; battery, resistor R and capacitor C in series.)

Solution. According to Kirchhoff's second law, at each moment of time the emf of the DC source is equal to the sum of the potential drop across the resistor and the capacitor voltage: ℰ = IR + U. Bearing in mind that I = dQ/dt and U = Q/C, we get ℰ = R dQ/dt + Q/C, or dQ/(Q − ℰC) = −(1/RC) dt. Integration from Q = 0 to Q and from t = 0 to t and appropriate transformations yield Q = ℰC[1 − exp(−t/RC)], whence I = (ℰ/R) exp(−t/RC) = I0 exp(−t/RC). The amount of heat generated by the current in the resistor R in the course of dt is dq = I2R dt = I02R exp(−2t/RC). Integration from t = 0 to t = ∞ yields q = I02R2C/2 = ℰ2C/2. The same amount of energy is stored by the capacitor when the latter is charged to a voltage equal to the source's emf. The total energy used up by the source, ∫0∞ℰI dt = ℰI0∫0∞e−t/(RC)dt, is equal to ℰ2C, which is the sum of two equal quantities ℰ2C/2.

Teacher's Note: Source energy ℰQ = ℰ2C splits into capacitor energy ℰ2C/2 and heat ℰ2C/2, whatever R is.

Exam Note: Compute heat, capacitor energy, source energy; compare.

Question 4.21. A charged capacitor is connected to an uncharged capacitor with the same capacitance. Determine the changes in the energies stored by the two capacitors and explain the origin of these changes from the viewpoint of energy conservation.

Solution. The energy stored by a charged capacitor can be written in the form W0 = Q2/2C. After the second (uncharged) capacitor is connected to the first, the total charge does not change while the capacitance doubles. Thus, the total energy stored by this system becomes W = Q2/4C, which is one-half of the initial energy. So where did the other half go to? As the charge is redistributed between the two capacitors, a current flows through the conductors connecting them and generates heat. In addition, there is always a magnetic field around a conductor with current, and this magnetic field carries energy, just as an electric field does. If the resistance of the conductors is low (zero in the case of superconductors), the difference between the initial and the final energy will go to the magnetic field. Eventually the second capacitor will become fully charged while the first capacitor will become completely discharged and the current will cease. Then the second capacitor will begin to discharge, and charge will flow to the first capacitor. This process will continue, that is, there will appear electromagnetic oscillations in which the energy will alternate between that of the electric field and the magnetic field.

Teacher's Note: Charge is conserved so energy halves (Q2/2C to Q2/4C); the missing half is heat and field energy.

Exam Note: Answer: half the energy lost as heat/field energy.

Question 4.22. A conducting disk is rotating with an angular velocity ω. Allowing for the fact that electrons are the current carriers in a conductor, determine the potential difference between the center of the disk and the edge. (Fig. 4.22: a disk rotating about its axis, with a measuring circuit between the axis and the rim.)

Solution. For an electron that is inside the disk at a distance r from the axis to move along a circle, there should be a force pulling it to the axis. According to Newton's second law, F = mω2r. This force is generated by a radial electric field caused by the redistribution of the electrons in the disk and is such that the force acting on the electron is F = eE = mω2r. If we substitute −dφ/dt for E and integrate from φ1 to φ2 and from 0 to R, where R is the radius of the disk, we get ∫dφ = −(mω2/e)∫0R r dr. As a result, we get the potential difference between the center of the disk and the edge: U = φ1 − φ2 = mω2R2/2e = mv2/2e (4.22.1), where v is the linear velocity of points at the edge of the disk. Theoretically formula (4.22.1) can be used to determine the electron's charge-to-mass ratio. But actually this constitutes a problem, as shown by an estimate of the potential difference between the axis and the edge. The electron charge is 1.6 × 10−19 C and the electron mass is 9.1 × 10−31 kg. We set the electron linear velocity on the edge at 300 m/s. The potential difference then proves to be less than 10−9 V (as printed; Corrected: with these numbers mv2/2e = 2.6 × 10−7 V, so the safe statement is "less than 10−6 V"). It is extremely difficult to measure such a quantity in such a rotating system.

Teacher's Note: Centripetal force on electrons comes from a radial electric field; integrate eE = mω2r from centre to rim.

Exam Note: Result U = mω2R2/2e.

Question 4.23. In the Tolman-Stewart experiment, a cylinder is mounted on a shaft and is rotated very rapidly. The surface of the cylinder is wound with many turns of wire of length l in a single layer. After the cylinder has been set spinning at a large angular velocity, it is braked to a stop as quickly as possible. In the circuit consisting of the wire and a measuring device, this braking manifests itself in a pulse of current caused by the potential difference that appears between the ends of the wire. If the potential difference is registered by an oscillograph, we obtain a curve similar to the one shown in the figure accompanying the problem, where time is laid off on the horizontal axis. How, knowing the initial linear velocity of the winding, the length of the wire, and the voltage oscillogram, can one determine the electron charge-to-mass ratio? (In the Tolman-Stewart experiment, the quantity measured was not the potential difference but the amount of electricity passing through the circuit. This was done using a device called the ballistic galvanometer.) (Fig. 4.23: U against t, a pulse rising and then decaying.)

Solution. Moving together with the cylinder, the electrons in the wire have a momentum mv each. When the cylinder is braked, the electrons continue to move, but the generated potential difference creates a braking electric field of strength E. The force acting on every electron in the wire is F = eU/l, with U the instantaneous potential difference. According to Newton's second law, Δmv = (e/l)∫0tU dt, where Δmv is the momentum lost by an electron during the entire braking time, which quantity is equal to the initial momentum mv. The charge-to-mass ratio for the electron is then e/m = vl/∫0∞U dt. The integral in the denominator can be evaluated by calculating the area under the voltage oscillogram.

Teacher's Note: Impulse of braking force eU/l equals the initial momentum mv, so e/m = vl over the oscillogram area.

Exam Note: Result e/m = vl/∫U dt.

Question 4.24. The section of a conductor between the points a and b is being heated. Does this lead to a redistribution of potential along the conductor (the arrow indicates the direction in which the current is flowing)? Will the passage of current change the temperature distribution in the conductor? (Fig. 4.24: a conductor ab, current flowing from left to right.)

Solution. The heating of the conductor will result in the electron diffusing into the neighborhood of section ab, with the potential of the conductor somewhat increasing. The current flowing in the conductor will have to overcome a potential barrier at point a. This requires additional energy, which will be taken from the metal. On the other hand, when passing through the conductor at point b, the current goes to a region with a lower potential, and in this place energy will be released to the metal. As a result, the point where the temperature is at a maximum will shift in the direction of current flow.

Teacher's Note: Heating drives electron diffusion, creating potential steps at a and b; energy is absorbed at a and released at b.

Exam Note: State both effects: potential changes, hot spot shifts along current.

Question 4.25. A constant voltage is applied to a metal wire. The current passing through the wire heats the wire to a certain temperature. Then half of the wire is cooled by a stream of air from a fan. How will the temperature of the other half of the wire change in the process? (Fig. 4.25: a wire stretched between two supports with a fan blowing on half of it.)

Solution. Prior to cooling, the resistance of the wire was the same over the entire length of the wire (precisely, the resistivity was the same at all points of the wire). When the fan is switched on, the resistance of the section that is being cooled will lower. This leads to a redistribution of the potential between the cooled and uncooled sections, with the greater voltage applied to the latter section, as a result of which its temperature increases. This phenomenon is enhanced by the fact that the resistance of the uncooled section somewhat grows with temperature, which leads to a still greater inhomogeneity in the distribution of the potential in both sections.

Teacher's Note: Cooling lowers the cooled half's resistance, so more voltage falls across the uncooled half, heating it further.

Exam Note: Answer: the other half becomes hotter.

Question 4.26. Two electric bulbs whose rated voltage is 127 V and whose rated wattages are 25 and 150 W are connected in series to a DC source of 220 V. Which of the two bulbs will burn out?

Solution. The resistances of bulbs with the same rated voltage are in inverse proportion to the rated wattages. Hence, the resistance of the bulb with the lower wattage is six times the resistance of the bulb with the higher wattage. When the bulbs are connected in series with the DC source, the current is the same and six-sevenths of the total voltage of 220 V, or 189 V, is applied to the first (25 W) bulb and one-seventh, to the second (150 W) bulb. Actually the difference is still greater because the resistance of the first bulb will increase due to overheating, while that of the second will decrease. Hence, the 25-W bulb must burn out.

Teacher's Note: R = V2/P gives 6:1 ratio; in series the 25 W bulb gets 189 V against its 127 V rating.

Exam Note: Answer: the 25 W bulb; show the 189 V share.

Question 4.27. A conductor and a semiconductor are connected in parallel. At a certain voltage both ammeters register the same current. Will this condition remain as such if the voltage of the DC source is increased? (Fig. 4.27: a conductor with ammeter A1 and a semiconductor with ammeter A2 in parallel branches.)

Solution. An increase in voltage will lead to an increase in the currents passing through the conductor and semiconductor, and this will lead to an increase in temperature of both. As a result the resistance of the conductor will increase and that of the semiconductor will decrease. Hence, the current through the semiconductor will increase greater than in proportion to the voltage, while the current through the conductor will increase lesser than in proportion to the applied voltage, with the result that the ammeter in the semiconductor circuit will register a higher current than the ammeter in the conductor circuit.

Teacher's Note: Heating raises a conductor's resistance but lowers a semiconductor's, so the semiconductor branch takes more current.

Exam Note: Answer: no; A2 reads more than A1.

Question 4.28. A conductor and a semiconductor are connected in series. The voltage applied to this system is selected in such a way that the readings of the voltmeters V1 and V2 coincide. Will this condition remain unchanged if the voltage of the DC source is increased? (Fig. 4.28: conductor with voltmeter V1 and semiconductor with voltmeter V2 in series.)

Solution. Prior to an increase in voltage, the resistances of the semiconductor and the conductor were equal. When the voltage is increased, the current in the circuit increases, too, and so does the temperatures of the semiconductor and conductor. This leads to a drop in the resistance of the semiconductor and an increase in the resistance of the conductor. The voltage between the semiconductor and conductor will redistribute in such a manner that the voltmeter connected to the conductor will register a higher voltage than the voltmeter connected to the semiconductor.

Teacher's Note: In series the same current heats both; conductor resistance rises, semiconductor's falls, so the conductor takes the larger voltage.

Exam Note: Answer: no; V1 reads higher than V2.

Question 4.29. A thermionic valve, or diode, has a heated filament and a plate near it. The dependence of the current flowing between filament and plate on the voltage applied to valve (the current-voltage characteristic) is as follows. First the current grows with voltage, but then goes into a plateau at a sufficiently high voltage. Why, notwithstanding the fact that the filament may emit the number of electrons required for the saturation current to set in, the latter does not manifest itself at an arbitrarily small voltage between the electrodes? In which respect does curve 1 differ from curve 2 from the standpoint of the experimental conditions if the two are obtained using the same device? (Fig. 4.29: current I against voltage U; curve 1 and curve 2 rise together, then flatten to plateaus, curve 2 plateau higher.)

Solution. The electrons leaving the filament, or cathode, create a negative space charge whose field does not let all the emitted electrons into the region. According to the Child-Langmuir theory developed for parallel plane electrodes on the assumption that the initial velocity of the electrons is zero, the current density between the electrodes is j = (4√2 ε0/9)√(e/m) U3/2/d2 (the three-halves power law). Here e and m are the electron charge and electron mass, U is the voltage drop across the electrodes, and d is the distance between the electrodes. On the current-voltage characteristic, the initial segment of the curve agrees with the three-halves power law. Then, as the electron cloud is dissipated, the current gradually reaches a plateau and saturation sets in, with the saturation current being the total flux of electrons that the cathode can deliver at a given temperature. The temperature dependence of the current density is given by the Richardson-Dushman equation jsat = A'T2 exp(−P/kT). The quantity P in the numerator of the exponent is the so-called work function, or the work that an electron must do to leave the metal. The other quantities in the equation are as follows: T the thermodynamic temperature, k the Boltzmann constant, A' = 6.02 × 105 A/m2·K2 is a constant that is a combination of universal constants (older value as printed; the modern value is about 1.2 × 106 A/m2·K2). The difference in the curves in the figure accompanying the problem lies in the temperature of the cathode, which is higher for curve 2.

Teacher's Note: Space charge near the cathode repels emitted electrons, giving j ∝ U3/2; saturation depends only on cathode temperature.

Exam Note: Saturation current rises with temperature: curve 2 is hotter.

Question 4.30. A cutoff voltage is applied between the cathode and the anode of a thermionic valve ("minus" at the anode and "plus" at the cathode). The cathode temperature, however, is sufficient for thermionic emission to manifest itself. If the direction of the electric field is reversed by applying between the cathode and the anode a voltage at which saturation current will flow through the valve, will the temperature of the cathode maintained in the cutoff direction of the field remain the same?

Solution. When thermoelectric current flows from the cathode to the anode, the electrons leaving the cathode carry away energy required for overcoming the potential barrier that exists at the metal-vacuum interface (the work function of the electrons), with the result that the cathode cools off. To maintain a constant cathode temperature, the filament current must be increased.

Teacher's Note: Every emitted electron removes its work-function energy from the cathode, so a larger emission current cools it.

Exam Note: Answer: no; the cathode cools, so filament current must rise.

Question 4.31. For a current passing through an electrolyte (Figure (a)), the distribution of potential between the electrodes is shown in Figure (b). Why, notwithstanding the fact that the electrodes are flat and the distance between them is much smaller than their linear dimensions, is the field between the electrodes nonuniform? (Fig. 4.31: (a) two flat electrodes in an electrolyte, + on the left, − on the right; (b) U against x, steep near both electrodes and flatter in the middle.)

Solution. When the potential difference between the electrodes is nil, the concentration of positive and negative ions (cations and anions) is the same in practically the entire volume. When an external voltage is applied, a current generated by the motions of cations to the cathode and anions to the anode begins to flow in the electrolyte. As a result, the regions near the electrodes prove to be depleted of ions whose sign is that of the electrode. Cations leave the anode and anions leave the cathode. For this reason, near the anode an excess of negative charge is formed, while an excess of positive charge is formed in the region near the cathode. All this leads to a distortion in the electric field. The enhanced field near the electrodes imparts to the ions an enhanced velocity. This ensures the flow of current under lower charge carrier concentrations.

Teacher's Note: Ions leave the electrode regions faster than they arrive, producing space charge there, which distorts the field.

Exam Note: Cause: volume charge near the electrodes.

Question 4.32. The distribution of potential between the cathode and anode in a glow discharge is shown in the figure accompanying the problem (the distance from the cathode is laid off on the horizontal axis). Within which regions of space is there a positive volume charge, a negative volume charge, and a volume charge that is practically zero? (Fig. 4.32: U against x, rising from the cathode to a maximum at point 1, falling to a minimum at point 2, then rising nearly linearly to the anode at point 3, with the numbers 1, 2, 3 marked on the horizontal axis.)

Solution. The sign of the volume charge is determined by the direction of convexity of the U vs. x curve (see Problems 3.28 and 3.29). The volume charge is positive where the curve is convex upward and negative where the curve is convex downward, while the volume charge is nil where the U vs. x dependence is represented by a straight line. Hence, the entire region between the cathode and the anode is divided, within the first approximation (i.e. ignoring certain details), into the cathode space (from point 0 to point 1 in the figure accompanying the problem) with a surplus positive charge, the Faraday dark space (from point 1 to point 2) with a negative charge, and the region of the "positive column" (from point 2 to point 3), which constitutes a plasma with practically equal concentrations of electrons and positive ions and, hence, with a net charge that is practically nil.

Teacher's Note: Poisson's equation links charge sign to curvature of U(x): convex up means positive, convex down means negative, straight means zero.

Exam Note: Name three regions with their charge signs.

Question 4.33. In the plasma of a gas discharge, the concentration of electrons and that of positive ions are practically the same. Does this mean that the current densities created by the motion of electrons and ions are also the same? Will an ammeter connected in series with the gas discharge gap show the sum of the electron and ion currents or their difference?

Solution. The conduction-current density is given by the formula j = e∑knkukZk (4.33.1), where e is the magnitude (without taking into account the sign) of the elementary charge (the electron charge), nk the concentration of the given type of charge carriers, uk the average directional velocity of the carriers, and Zk the charge number, or valence, of the carriers. For an electron Z = −1, while for a positive doubly charged ion (say, He++) Z = +2. Electron velocities exceed ion velocities by a factor of 10 or even 100, with the result that even at equal concentrations the electron current is much stronger than the ion current. Since in an electric field electrons and ions move in opposite directions, we can assume that the electron velocity is negative if the ion velocity is set positive. Since the number Z for electrons is negative, the signs of the products in (4.33.1) coincide, with the result that the ammeter in the gas discharge circuit will register the total current of electrons and ions.

Teacher's Note: Electrons are far more mobile than ions; opposite motion and opposite charge make the two currents add.

Exam Note: Answer: not equal; currents add.

Question 4.34. A negatively charged particle is accelerated in its motion from a cathode C to an anode A, passes through an aperture in the latter, and moves toward a Faraday cylinder F that is at the same potential as the anode (Figure (a)). For the sake of simplicity it will be assumed that the particle moves from A to F with a constant velocity. Determine the moment of time when a measuring device G in the circuit will register a current (the time is reckoned from the moment when the particle leaves the anode) and the form of the current, that is, whether the current is in the form of a pulse when the particle leaves the anode (Figure (b)) or whether it is a pulse when the particle enters the Faraday cylinder (Figure (c)), or whether there are two pulses (one when the particle leaves the anode and the other when the particle enters the Faraday cylinder; see Figure (d)) or whether the current is steady over the entire motion of the particle from the anode to the Faraday cylinder (Figure (e)). (Fig. 4.34: (a) the circuit with cathode C, anode A, Faraday cylinder F and galvanometer G; (b) to (e) current I against time t for the four options: (b) a pulse at the start, (c) a pulse at the end, (d) two pulses, (e) a constant current throughout.)

Solution. As the particle moves from the anode to the Faraday cylinder, the field in the region between A and F constantly changes. When the particle leaves the anode (through the aperture) and is moving toward the Faraday cylinder, it induces positive charges on these electrodes, and the magnitude of these charges constantly changes. The density of these charges on the anode decreases while that on the Faraday cylinder increases (the variation in the distribution of electric charge for three moments in time is shown in the figure accompanying the answer). For this reason, in the region of space between A and F there appears a continuous displacement current, which means that an exact replica of this current appears in the circuit. The current in the circuit can be graphically represented as a consequence of the fact that in approaching the Faraday cylinder the particle repels, so to say, the electrons which, in effect, move toward the anode through the measuring device G. Thus, the current in the circuit exists during the entire time of motion of the particle between the anode and the Faraday cylinder, as shown in Figure (e) accompanying the problem.
(Fig. 4.34 of the answer: three snapshots, at t1, t2, t3, of the field lines and induced charges between A and F, the induced charge shifting from the anode to the cylinder.)

Teacher's Note: The induced charge moves continuously from anode to cylinder while the particle travels, so a steady current flows throughout.

Exam Note: Answer: option (e), steady current during transit.

Question 4.35. The behavior of the potential energy of an electron inside and outside a metal is shown in Figures (a) and (b) for two metals. The same figures indicate the limiting kinetic energies WF of electrons in the metals (the Fermi levels) at T = 0 K. If the metals are brought into contact, what will be the values of the internal and external contact potential differences? In which metal will the electron concentration be higher? (Fig. 4.35: for each metal, a potential well with depth, work function eφ1 or eφ2, and Fermi energy WF1 or WF2 marked.)

Solution. If two metals are brought into contact, the limiting energies of the electrons will establish themselves at a common level (the common Fermi level; see the figure accompanying the answer). The difference between the height of a potential barrier and the Fermi level determines the external work function eφ. The difference between the two work functions (for the two barriers) is equal to the external contact potential difference. To transfer an electron from the surface of metal 2 to the surface of metal 1 requires performing an amount of work equal to eΔφ. The distance between the levels of minimal electron energy in the metals determines the internal contact potential difference ΔWF. According to the quantum theory of metals, the Fermi level at 0 K is pinned at (h2/2m) × (3n/π)2/3 in the book as printed, where h is the Planck constant, m the electron mass and n the electron concentration in a metal. Corrected: the Fermi energy with spin degeneracy is WF = (h2/8m)(3n/π)2/3 = (h2/2m)(3n/8π)2/3; the printed prefactor is four times too large (for copper, n = 8.5 × 1028 m−3, it gives 7.0 eV only with h2/8m). In either form WF increases with n, so the concentration of electrons in metal 1 is higher.
(Fig. 4.35 of the answer: both wells with a common Fermi level; the minimal-energy levels differ by ΔWF and the vacuum levels by eΔφ.)

Teacher's Note: Contact aligns Fermi levels; external contact p.d. is the work-function difference; higher density gives higher WF.

Exam Note: Link WF ∝ n2/3 to which metal has more electrons.

Question 4.36. The energy distribution function for electrons in a metal at absolute zero can be written as follows: f(W) = CW1/2, (4.36.1) where C is a constant coefficient that is a combination of universal constants, which is the limiting energy, or the Fermi level. Using (4.36.1), establish how the limiting energy depends on electron concentration. (Fig. 4.36: f(W) rising as W1/2 up to WF, then falling to zero.)

Solution. The concentration of electrons whose energy ranges from W to W + ΔW is dn = f(W) dW = CW1/2dW, in accordance with Eq. (4.36.1). Integrating this expression from zero to the limiting energy, we obtain the concentration of electrons in the entire energy range: n = C∫0WFW1/2dW = (2/3)CWF3/2. Hence, WF ∝ n2/3. As is proved in the quantum theory of metals, WF is given by the following formula (with due regard for universal constants): WF = (h2/2m)(3n/π)2/3 as printed. Corrected: WF = (h2/8m)(3n/π)2/3, which agrees with n = (2/3)CWF3/2 for C = 4π(2m)3/2/h3 and gives 7.0 eV for copper.

Teacher's Note: Integrating CW1/2 up to WF gives n ∝ WF3/2, so WF ∝ n2/3.

Exam Note: Show the integral; state WF ∝ n2/3.

Question 4.37. The dependence of the logarithm of conductivity, ln σ, on T−1, where T is the temperature, for two semiconductors is shown in the figure. In which of the two semiconductors is the gap (the forbidden band) between the valence band and the conduction band wider? (Fig. 4.37: two straight lines with negative slope, line 2 less steep than line 1.)

Solution. The electrical conductivity (specific conductance) of a semiconductor depends on temperature according to the following law: σ = σ0 exp(−W/kT), or ln σ = ln σ0 − W/kT, where W is the width of the forbidden band. This law implies that the wider the forbidden band, the steeper the straight line representing the ln σ vs. T−1 dependence. Hence, semiconductor 1 has a wider forbidden band.

Teacher's Note: Slope of ln σ against 1/T equals −W/k, so the steeper line means the wider band gap.

Exam Note: Answer: semiconductor 1 (steeper line).

Question 4.38. The dependence of the logarithm of conductivity, ln σ, on 1/T for two semiconductors is shown schematically in the figure. In which respect do these semiconductors differ? (Fig. 4.38: two curves, each with a steep upper (high-temperature) section and a gentler lower (low-temperature) section; the upper sections coincide, the lower sections are parallel, curve 1 lying above curve 2.)

Solution. Since the upper sections of the curves for the two semiconductors coincide and the slopes of the lower sections are smaller than those of the upper, the intrinsic conductivities are the same. Also, since the lower sections of the curves slope in the same manner (i.e. the slopes are equal), the width of the forbidden band for the impurities is the same for both semiconductors. Thus, these diagrams can be interpreted as a characteristic of impurity semiconductors with different concentrations of the same impurities. For a fixed temperature, a higher conductivity corresponds to a higher located characteristic, 1, and, hence, a higher concentration of impurities.

Teacher's Note: Same intrinsic section and same impurity slope mean same material and impurity type; only impurity concentration differs.

Exam Note: Answer: curve 1 has the higher impurity concentration.

Question 4.39. The distribution of potential near the boundary between two semiconductors with different types of conduction depends on the direction of the applied external voltage. Which distribution corresponds to the blocking direction and which, to conduction? To what semiconductors do the left and right branches of the curves in the figure belong? (Fig. 4.39: potential φ against x for curves 0, 1, 2, all passing through the origin, falling from positive on the left to negative on the right; curves 1 and 2 are the two modified curves, one steeper and one flatter than curve 0.)

Solution. The diffusion of electrons from an n-type semiconductor into a p-type one and of holes from the p-type semiconductor to the n-type one leads to the appearance of a positive potential on the n-type semiconductor (the left branch of curve 0) and a negative potential on the p-type semiconductor (the right branch of the same curve). If we now apply a positive potential to the n-type semiconductor and a negative potential to the p-type, the potential difference between the two semiconductors will increase (curve 1), whence the boundary between the two semiconductors is depleted of charge carriers as a result of electrons being drained to the n-type semiconductor and holes, to the p-type semiconductor. Such a direction of the potential difference is the cut-off one. When the external voltage is applied in the reverse direction (curve 2), the potential difference lowers, it proves easier for the electrons to move to the p-type semiconductor and the holes, to the n-type. This direction is the conducting one.

Teacher's Note: Forward bias lowers the junction barrier (curve 2), reverse bias raises it (curve 1); left is n-type, right p-type.

Exam Note: Curve 1 blocking, curve 2 conducting; left n, right p.

Question 4.40. The current-voltage characteristic of a semiconductor diode based on the properties of a p-n junction has two branches: the upper right branch and the lower left branch. Since the right branch corresponds to small voltages and the left branch to considerably higher voltages (with the currents in the conductive direction being much higher than the currents in the blocking direction), the two branches are constructed using different scales. What is the explanation for the existence of the left branch and in what manner does the current in the blocking direction depend on the temperature of the diode? (Fig. 4.40: I in mA from 0 to 80 against U in volts; right branch rises steeply from 0 to about 4 V; left branch from −400 V to 0 with a current of about −5 μA.)

Solution. Every semiconductor possesses intrinsic conduction in addition to extrinsic (or impurity) conduction. Intrinsic conduction is caused by the transfer of electrons from the valence band to the conduction band and by simultaneous formation of holes in the valence band. Intrinsic conduction is of a mixed nature for this reason, and because of this the n-type semiconductor carries a small number of holes while the p-type semiconductor carries a small number of electrons. When a voltage is applied in the cut-off direction, these charge carriers constitute the so-called reverse current. As the temperature of a semiconductor diode is increased, the electron and hole concentrations grow, as a result of which conductivity in the cut-off direction grows, too. The reverse current reaches a plateau when practically all the "alien" charge carriers (holes in the n-type semiconductor and electrons in the p-type) participate. Usually this current is several orders of magnitude less than the direct current, with the plateau reached at relatively high voltages. The direct current grows with voltage very rapidly, since as the voltage is increased, it becomes easier for the charge carriers to pass through the junction.

Teacher's Note: Reverse current comes from thermally generated minority carriers, so it grows with temperature and saturates at a small value.

Exam Note: Answer: minority carriers; reverse current rises with temperature.

Question 4.41. The phenomenon of secondary electron emission consists in the following. When electrons bombard a solid surface, the surface emits secondary electrons (and partially reflects the primary electrons, which impinge on the surface). Secondary electron emission is characterized by the secondary emission coefficient σ, which is the ratio of the secondary electron current to the primary current. The dependence of the secondary emission coefficient on the primary electron energy W1 for a certain dielectric is depicted in the figure. At σ = 1 the surface of the dielectric does not change its potential under electron bombardment, since the number of electrons leaving the surface every second is equal in this case to the number of electrons bombarding the surface every second. The two points a and b on the σ vs. W1 curve correspond to σ = 1. At which point is the process stable and at which is it unstable? (Fig. 4.41: σ against W1, rising from 0 through a at σ = 1 to a maximum, then falling and crossing σ = 1 again at b.)

Solution. Let us suppose that there is a small deviation from the state with σ = 1. If σ drops at point a, the number of electrons impinging on the surface is smaller than the number of electrons leaving the surface, with the surface acquiring a negative potential, which brings down σ still further. And this leads to a further increase in the negative potential. The process continues until the current of primary electrons becomes totally cut off. If at the same point the value of σ increases somewhat, the surface acquires a positive potential, the velocity of the electrons increases, and the current continues to grow, which leads to an increase in σ, up to the maximum on the curve, and then to point b, where σ = 1, just as at point a. Similar reasoning leads us to the conclusion that small variations in σ at point b change the potential of the surface in such a way that σ returns to its initial value σ = 1. Thus, point a corresponds to an unstable state, while point b corresponds to a stable state. For a small deviation from the state of equilibrium corresponding to point a, the surface acquires a potential that either completely cuts off the current of the primary electrons or corresponds to that at point b.

Teacher's Note: At a a small change in σ is amplified by surface potential; at b it is opposed, restoring σ=1.

Exam Note: Answer: a unstable, b stable.

Question 4.42. Under secondary electron emission (see Problem 4.41), the energy distribution function F(W2) for secondary electrons is represented sufficiently well by two curves (1 and 2) shown in the figure accompanying the problem. Which of the two curves represents the primary electrons and which, the "true" secondary electrons? (Fig. 4.42: F(W2) against W2; curve 1 is a broad low hump over low energies, curve 2 a very narrow tall peak at the highest energy.)

Solution. The reflected electrons retain practically all their initial energy and, hence, correspond to curve 2 in the figure accompanying the problem. Secondary electrons, on the other hand, are freed from the solid bombarded with the primary electrons at the expense of the energy of the primary electrons, and this energy is distributed between the emitted electrons. The energy of the latter is, as a rule, considerably less than that of the primary electrons. Moreover, while all the reflected electrons have velocities that are concentrated within a narrow interval and have energies close to those of the primary electrons, the secondary electrons form a broad spectrum of velocities. The "true" secondary electrons are represented by curve 1 in the figure accompanying the problem.

Teacher's Note: Reflected primaries keep nearly their full energy (narrow peak); true secondaries share energy, giving a broad low-energy spectrum.

Exam Note: Curve 2: primary (reflected); curve 1: true secondary.

LA Sena Solutions for JEE Mathematics: LA Sena Solutions Physics Chapter 4 Direct Current

Access JEE Mathematics Solutions

Access the complete chapter-wise PDF for LA Sena Solutions Physics Chapter 4 Direct Current. These structured LA Sena Solutions solutions for JEE Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.

Detailed Calculation Guides for JEE

Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.

Additional Study Materials for 2026

In addition to these LA Sena Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.

FAQs

What are these LA Sena Solutions for JEE Physics?

They are chapter-wise solved questions from the LA Sena book for JEE Physics. Each answer is explained step by step so you can check your work and revise.

Are the LA Sena JEE Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these LA Sena solutions for JEE Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising LA Sena JEE Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these JEE Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.