Step-by-Step IE Irodov Solutions for JEE Physics Chapter 03 Laws Of Conservation Of Energy Momentum And Angular Momentum
Explore reliable textbook solutions for Chapter 03 Laws Of Conservation Of Energy Momentum And Angular Momentum tailored for JEE learners using IE Irodov methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.
Download Chapter 03 Laws Of Conservation Of Energy Momentum And Angular Momentum Textbook Solutions PDF
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
3. Laws of Conservation of Energy, Momentum and Angular Momentum - Problems 161-199
Part 3 (Q. 161-180)
Question 161. A cannon of mass M starts sliding freely down a smooth inclined plane at an angle α to the horizontal. After the cannon covered the distance l, a shot was fired, the shell leaving the cannon in the horizontal direction with a momentum p. As a consequence, the cannon stopped. Assuming the mass of the shell to be negligible, as compared to that of the cannon, determine the duration of the shot.
Solution. Velocity of the cannon (and of the shell, whose mass is negligible) just before the shot equals √(2gl sin α) down the incline, taken as the positive x-axis. Apply the linear impulse-momentum theorem in projection form along x for the system (cannon + shell): Δpx = FxΔt.
p cos α − M√(2gl sin α) = Mg sin α · Δt (as the mass of the shell is negligible)
or, Δt = [p cos α − M√(2gl sin α)] / (Mg sin α).
Teacher's Note: Use impulse along the incline; only the gravity component Mg sin α acts during the short shot.
Exam Note: Choose the incline as axis; resolve the shell momentum.
Question 162. A horizontally flying bullet of mass m gets stuck in a body of mass M suspended by two identical threads of length l (Fig. 1.42). As a result, the threads swerve through an angle θ. Assuming m << M, find: (a) the velocity of the bullet before striking the body; (b) the fraction of the bullet's initial kinetic energy that turned into heat.
Solution. From conservation of momentum for the system (bullet + body) along the initial direction of the bullet: mv0 = (m + M)v, or v = mv0/(m + M).
Corrected (the printed solution stops here; completed): After impact the system rises through a height l(1 − cos θ), so ½(m + M)v² = (m + M)g l(1 − cos θ), giving v = √(2gl(1 − cos θ)) = 2√(gl) sin(θ/2).
(a) v0 = (m + M)v/m ≈ (M/m)·2√(gl) sin(θ/2) (as m << M).
(b) Heat/initial KE = [½mv0² − ½(m + M)v²] / (½mv0²) = 1 − m/(m + M) = M/(m + M) ≈ 1 − m/M.
Teacher's Note: Momentum conserved in the collision; energy conserved only afterwards, during the swing. Do not mix the stages.
Exam Note: Separate collision stage from swing stage.
Question 163. A body of mass M (Fig. 1.43) with a small disc of mass m placed on it rests on a smooth horizontal plane. The disc is set in motion in the horizontal direction with velocity v. To what height (relative to the initial level) will the disc rise after breaking off the body M? The friction is assumed to be absent. (The body M has a smooth horizontal top that curves upward into a vertical-tangent surface; the disc slides up this curve and leaves it.)
Solution. From conservation of momentum along the x-axis for the system (disc + body): mv = (m + M)v′x, or v′x = mv/(m + M) (1).
From energy conservation for the same system in the field of gravity: ½mv² = ½(m + M)v′x² + ½mv′y² + mgh′, where h′ is the height of the break-off point from the initial level. Using (1): v′y² = v² − mv²/(m + M) − 2gh′.
If h″ is the height risen by the disc after break-off, then v′y² = 2gh″. So 2g(h″ + h′) = v² − mv²/(M + m).
Hence the total height raised from the initial level = h′ + h″ = Mv² / [2g(M + m)].
Teacher's Note: At break-off the disc shares the body's horizontal velocity; only the vertical part goes into height.
Exam Note: Write momentum (horizontal) and energy equations for the system.
Question 164. A small disc of mass m slides down a smooth hill of height h without initial velocity and gets onto a plank of mass M lying on the horizontal plane at the base of the hill (Fig. 1.44). Due to friction between the disc and the plank the disc slows down and, beginning with a certain moment, moves in one piece with the plank. (1) Find the total work performed by the friction forces in this process. (2) Can it be stated that the result obtained does not depend on the choice of the reference frame?
Solution. (a) When the disc slides onto the plank it has velocity v = √(2gh). Due to friction the disc slows down and after some time moves in one piece with the plank with velocity v′. From momentum conservation for (disc + plank) along the horizontal: mv = (m + M)v′, or v′ = mv/(m + M).
From the equation for the increment of total mechanical energy of the system: ½(M + m)v′² − ½mv² = Afr, i.e. ½(M + m)m²v²/(m + M)² − ½mv² = Afr, so ½v²[m²/(M + m) − m] = Afr.
Hence Afr = −[mM/(m + M)]gh = −μgh, where μ = mM/(m + M) is the reduced mass.
(b) Look at the problem from a frame in which the hill (together with the disc on it) moves to the right with speed u. In this frame the speed of the disc when it just gets onto the plank is, by the law of addition of velocities, ṽ = u + √(2gh). Similarly the common speed of plank and disc when they move together is ṽ′ = u + [m/(m + M)]√(2gh). Then, as above, Afr = ½(m + M)ṽ′² − ½mṽ² − ½Mu². Expanding, the terms in u cancel and Afr = −μgh again.
Thus the result does not depend on the choice of reference frame. Note, however, that it would be incorrect to apply the 'conservation of energy' formula in the frame in which the hill is moving: the energy carried by the hill is not negligible in that frame.
Teacher's Note: Friction work between two bodies is the same in all inertial frames: −μgh with reduced mass μ.
Exam Note: Quote μgh and state frame-independence.
Question 165. A stone falls down without initial velocity from a height h onto the Earth's surface. The air drag assumed to be negligible, the stone hits the ground with velocity v0 = √(2gh) relative to the Earth. Obtain the same formula in terms of the reference frame 'falling' to the Earth with a constant velocity v0.
Solution. In a frame moving relative to the earth, one has to include the kinetic energy of the earth as well as the earth's acceleration to be able to apply conservation of energy. In a reference frame falling to the earth with velocity v0, the stone is initially going up with velocity v0 and so is the earth. The final velocity of the stone is 0 = v0 − gt and that of the earth is v0 + (m/M)gt (M is the mass of the earth), from Newton's third law, where t = time of fall. From conservation of energy:
½mv0² + ½Mv0² + mgh = ½M(v0 + (m/M)v0)²
Hence ½v0²(m + m²/M) = mgh. Neglecting m/M in comparison with 1, we get v0² = 2gh, or v0 = √(2gh).
The point is that in the earth's rest frame the effect of the earth's acceleration is of order m/M and can be neglected, but in a frame moving with respect to the earth the effect of the earth's acceleration must be kept because it is of order one (i.e. large).
Teacher's Note: In a moving frame the Earth's kinetic energy changes too, so it cannot be ignored there.
Exam Note: Include Earth's kinetic energy; then neglect m/M.
Question 166. A particle of mass 1.0 g moving with velocity v1 = 3.0i − 2.0j experiences a perfectly inelastic collision with another particle of mass 2.0 g and velocity v2 = 4.0j − 6.0k. Find the velocity of the formed particle (both the vector v and its modulus), if the components of the vectors v1 and v2 are given in the SI units.
Solution. From conservation of momentum for the closed system 'both colliding particles': m1v1 + m2v2 = (m1 + m2)v,
or, v = (m1v1 + m2v2)/(m1 + m2) = [1(3i − 2j) + 2(4j − 6k)]/3 = i + 2j − 4k.
Hence |v| = √(1 + 4 + 16) m/s = 4.6 m/s.
Teacher's Note: Momentum is a vector: add components separately; masses can stay in grams since they form a ratio.
Exam Note: Add vector components, then take the modulus.
Question 167. Find the increment of the kinetic energy of the closed system comprising two spheres of masses m1 and m2 due to their perfectly inelastic collision, if the initial velocities of the spheres were equal to v1 and v2.
Solution. For a perfectly inelastic collision, in the C.M. frame the final kinetic energy of the colliding system (both spheres) becomes zero. Hence the initial kinetic energy of the system in the C.M. frame is completely turned into the internal energy Q of the formed body:
Q = T̃i = ½μ|v1 − v2|².
Now from energy conservation ΔT = −Q = −½μ|v1 − v2|², where μ = m1m2/(m1 + m2).
In the lab frame the same result is obtained as ΔT = ½|m1v1 + m2v2|²/(m1 + m2) − ½(m1|v1|² + m2|v2|²) = −½μ|v1 − v2|².
Teacher's Note: Kinetic energy lost equals the C.M.-frame energy, ½μ(relative speed)²; it depends only on relative velocity.
Exam Note: State ΔT = −½μ|v1 − v2|² with μ defined.
Question 168. A particle of mass m1 experienced a perfectly elastic collision with a stationary particle of mass m2. What fraction of the kinetic energy does the striking particle lose, if (a) it recoils at right angles to its original motion direction; (b) the collision is a head-on one?
Solution. (a) Let the initial and final velocities of m1 and m2 be u1, 0 and v1, v2 respectively; m2 moves at angle θ to the original direction and m1 moves perpendicular to it. From conservation of momentum along the horizontal and vertical directions:
m1u1 = m2v2 cos θ (1) and m1v1 = m2v2 sin θ (2).
Squaring (1) and (2) and adding: m2²v2² = m1²(u1² + v1²).
From kinetic energy conservation, ½m1u1² = ½m2v2² + ½m1v1² (3), or m1(u1² − v1²) = m2v2² = (m1²/m2)(u1² + v1²),
or, u1²(1 − m1/m2) = v1²(1 + m1/m2), or (v1/u1)² = (m2 − m1)/(m1 + m2) (4).
So the fraction of kinetic energy lost by particle 1 = (½m1u1² − ½m1v1²)/(½m1u1²) = 1 − v1²/u1² = 1 − (m2 − m1)/(m1 + m2) = 2m1/(m1 + m2) (5).
(b) When the collision is head-on, m1u1 = m1v1 + m2v2, so v2 = m1(u1 − v1)/m2, and from conservation of kinetic energy, ½m1u1² = ½m1v1² + ½m2[m1(u1 − v1)/m2]²,
or, v1(1 + m1/m2) = u1(m1/m2 − 1), or v1/u1 = (m1/m2 − 1)/(1 + m1/m2) (6).
Fraction of kinetic energy lost = 1 − v1²/u1² = 1 − [(m1 − m2)/(m1 + m2)]² = 4m1m2/(m1 + m2)².
Teacher's Note: Perpendicular recoil needs m2 > m1; head-on energy transfer peaks (100%) when masses are equal.
Exam Note: Combine momentum and energy equations; give both fractions.
Question 169. Particle 1 experiences a perfectly elastic collision with a stationary particle 2. Determine their mass ratio, if (a) after a head-on collision the particles fly apart in the opposite directions with equal velocities; (b) the particles fly apart symmetrically relative to the initial motion direction of particle 1 with the angle of divergence θ = 60°.
Solution. (a) When the particles fly apart in opposite directions with equal speeds (say v), momentum conservation gives m1u + 0 = (m2 − m1)v (1), and kinetic energy conservation gives ½m1u² = ½m1v² + ½m2v², or m1u² = (m1 + m2)v² (2).
From (1) and (2): m1u² = (m1 + m2)m1²u²/(m2 − m1)², or m2² − 3m1m2 = 0. Hence m2 = 3m1, i.e. m1/m2 = 1/3.
(b) Flying apart symmetrically with divergence θ = 60° (each at θ/2 to the initial direction), momentum conservation along and perpendicular to the initial direction gives:
m1u1 = m1v1 cos(θ/2) + m2v2 cos(θ/2) (1)
m1v1 sin(θ/2) = m2v2 sin(θ/2), or m1v1 = m2v2 (2)
Kinetic energy: ½m1u1² = ½m1v1² + ½m2v2² (3)
From (1) and (2): u1 = 2v1 cos(θ/2) (4). From (2), (3) and (4): 4m1cos²(θ/2)v1² = m1v1² + m2m1²v1²/m2², or 4cos²(θ/2) = 1 + m1/m2, so m1/m2 = 4cos²(θ/2) − 1. Putting θ = 60°: m1/m2 = 4 × 3/4 − 1 = 2.
Teacher's Note: Symmetric scattering forces equal transverse momenta, m1v1 = m2v2; then energy fixes the mass ratio.
Exam Note: Answers: (a) m1/m2 = 1/3; (b) m1/m2 = 2.
Question 170. (The statement of this problem is not printed in the source PDF; reconstructed from the solution.) Two identical smooth balls collide: one is stationary and the other moves with velocity u at an angle α to the line joining their centres at the moment of impact (Fig.). Find the maximum fraction η of the initial kinetic energy that is stored as deformation energy at the moment of greatest deformation, for α = 45°.
Solution. If (v1x, v1y) are the instantaneous velocity components of the incident ball and v2x, v2y those of the struck ball at the same moment, then since there are no external impulsive forces (other than the mutual interaction of the balls) we have:
u sin α = v1y, v2y = 0, and mu cos α = mv1x + mv2x.
The impulsive force of mutual interaction satisfies d(v1x)/dt = F/m = −d(v2x)/dt. (F is along the x axis as the balls are smooth, so the y component of momentum is not transferred.) Since the loss of K.E. is stored as deformation energy D:
D = ½mu² − ½mv1² − ½mv2² = ½mu²cos²α − ½mv1x² − ½mv2x² = (1/2m)[m²u²cos²α − m²v1x² − (mu cos α − mv1x)²] = m(v1xu cos α − v1x²) = m[u²cos²α/4 − (u cos α/2 − v1x)²].
D is maximum when v1x = u cos α/2, and Dmax = mu²cos²α/4. Then η = Dmax/(½mu²) = ½cos²α = 1/4 (for α = 45°).
Teacher's Note: At maximum deformation both balls share the same normal velocity component; only the normal part of KE is stored.
Exam Note: Reconstructed statement; answer η = (1/2)cos²α.
Question 171. A shell flying with velocity v = 500 m/s bursts into three identical fragments so that the kinetic energy of the system increases η = 1.5 times. What maximum velocity can one of the fragments obtain?
Solution. From the conservation of linear momentum of the shell just before and after its fragmentation: 3mv = m(v1 + v2 + v3), i.e. 3v = v1 + v2 + v3 (1), where v1, v2, v3 are the velocities of the fragments.
From the energy condition: 3ηv² = v1² + v2² + v3² (2).
Now ṽi = viC = vi − vC = vi − v (3), where vC = v is the velocity of the C.M. of the fragments (the velocity of the shell). In the C.M. frame the linear momentum of the system is zero, so ṽ1 + ṽ2 + ṽ3 = 0 (4).
Using (3) and (4) in (2): 3ηv² = (v + ṽ1)² + (v + ṽ2)² + (v − ṽ1 − ṽ2)² = 3v² + 2ṽ1² + 2ṽ2² + 2ṽ1·ṽ2,
or, 2ṽ1² + 2ṽ1ṽ2 cos θ + 2ṽ2² + 3(1 − η)v² = 0 (5).
The problem being symmetrical, we can look for the maximum of any one fragment; it is the same for each. For ṽ1 to be real in Eq. (5): 4ṽ2²cos²θ ≥ 8(2ṽ2² + 3(1 − η)v²), or 6(η − 1)v² ≥ (4 − cos²θ)ṽ2².
So ṽ2 ≤ v√[6(η − 1)/(4 − cos²θ)], i.e. ṽ2(max) = √(2(η − 1))·v (the maximum, reached when cos²θ = 1).
Hence v2(max) = |v + ṽ2|max = v + √(2(η − 1))·v = v(1 + √(2(η − 1))) = 1 km/s.
Thus, owing to the symmetry, v1(max) = v2(max) = v3(max) = v(1 + √(2(η − 1))) = 1 km/s.
Teacher's Note: Work in the C.M. frame, where fragment momenta sum to zero; maximum when the other two move together.
Exam Note: Answer 1 km/s; state C.M.-frame argument.
Question 172. Particle 1 moving with velocity v = 10 m/s experienced a head-on collision with a stationary particle 2 of the same mass. As a result of the collision, the kinetic energy of the system decreased by η = 1.0%. Find the magnitude and direction of the velocity of particle 1 after the collision.
Solution. Since the collision is head-on, particle 1 continues along the same line as before the collision, but the magnitude of its velocity changes. Let particle 1 move with velocity v1 and particle 2 with v2 after the collision (initial velocity u = v). Conservation of momentum: mu = mv1 + mv2, or u = v1 + v2 (1).
From the given condition, η = [½mu² − (½mv1² + ½mv2²)]/(½mu²) = 1 − (v1² + v2²)/u², or v1² + v2² = (1 − η)u² (2).
From (1) and (2): v1² + (u − v1)² = (1 − η)u², or 2v1² − 2uv1 + ηu² = 0.
So v1 = [2u ± √(4u² − 8ηu²)]/4 = ½u(1 ± √(1 − 2η)). The positive sign gives the velocity of the 2nd particle, which lies ahead; the negative sign is correct for v1.
Corrected: v1 = ½u(1 − √(1 − 2η)) = ½ × 10 × (1 − √0.98) = 0.05 m/s (the printed value '5 m/s' is wrong). Particle 1 continues moving in the same direction as before. Note that v1 = 0 if η = 0, as it must.
Teacher's Note: Two roots of the quadratic belong to the two particles; the slower one is the incident particle after impact.
Exam Note: Give 0.05 m/s, same direction; check η = 0 limit.
Question 173. A particle of mass m having collided with a stationary particle of mass M deviated by an angle π/2 whereas the particle M recoiled at an angle θ = 30° to the direction of the initial motion of the particle m. How much (in per cent) and in what way has the kinetic energy of this system changed after the collision, if M/m = 5.0?
Solution. Since no external impulsive force is effective on the system 'M + m', its total momentum along any direction remains conserved. From px = const: mu = Mv1 cos θ, or v1 = (m/M)·u/cos θ (1). From py = const: mv2 = Mv1 sin θ, or v2 = (M/m)v1 sin θ = u tan θ [using (1)].
Final kinetic energy of the system Tf = ½mv2² + ½Mv1², and initial kinetic energy = ½mu². So
% change = (Tf − Ti)/Ti × 100 = [½mu²tan²θ + ½M(m²/M²)u²/cos²θ − ½mu²]/(½mu²) × 100 = (tan²θ + (m/M)sec²θ − 1) × 100.
Putting the values of θ and m/M: tan²30° = 1/3, sec²30° = 4/3, m/M = 0.2, so the change = (1/3 + 0.2667 − 1) × 100 = −40%. The kinetic energy decreases by 40%.
Teacher's Note: Use momentum components along and across the initial direction, then compare kinetic energies as a ratio.
Exam Note: Answer: kinetic energy decreases by 40%.
Question 174. A closed system consists of two particles of masses m1 and m2 which move at right angles to each other with velocities v1 and v2. Find: (a) the momentum of each particle and (b) the total kinetic energy of the two particles in the reference frame fixed to their centre of inertia.
Solution. (a) Let the particles m1 and m2 move with velocities v1 and v2 respectively. On the basis of the solution of problem 1.147 (b), the momentum of each particle in the C.M. frame is p̃ = μvrel = μ|v1 − v2|. As v1 ⊥ v2, p̃ = μ√(v1² + v2²), where μ = m1m2/(m1 + m2).
(b) Again from 1.147 (b): T̃ = ½μvrel² = ½μ|v1 − v2|². So T̃ = ½μ(v1² + v2²).
Teacher's Note: In the C.M. frame the two momenta are equal and opposite, each of magnitude μ × relative speed.
Exam Note: Use perpendicular velocities: |v1 − v2|² = v1² + v2².
Question 175. A particle of mass m1 collides elastically with a stationary particle of mass m2 (m1 > m2). Find the maximum angle through which the striking particle may deviate as a result of the collision.
Solution. From conservation of momentum, p1 = p1′ + p2′, so (p1 − p1′)² = p1² − 2p1p1′cos θ1 + p1′² = p2′².
From conservation of energy: p1²/2m1 = p1′²/2m1 + p2′²/2m2.
Eliminating p2′ we get 0 = p1′²(1 + m2/m1) − 2p1′p1cos θ1 + p1²(1 − m2/m1).
This quadratic equation for p1′ has a real solution in terms of p1 and cos θ1 only if 4cos²θ1 ≥ 4(1 − m2²/m1²), or sin²θ1 ≤ m2²/m1², or sin θ1 ≤ +m2/m1 or sin θ1 ≥ −m2/m1.
This clearly implies (since only the + sign makes sense) that sin θ1,max = m2/m1, i.e. θ1,max = sin−1(m2/m1).
Teacher's Note: A heavier particle cannot bounce back: its deflection is capped by a real-root (discriminant) condition.
Exam Note: Answer sin θmax = m2/m1; show discriminant step.
Question 176. Three identical discs A, B, and C (Fig. 1.45) rest on a smooth horizontal plane. The disc A is set in motion with velocity v after which it experiences an elastic collision simultaneously with the discs B and C. The distance between the centres of the latter discs prior to the collision is η times greater than the diameter of each disc. Find the velocity of the disc A after the collision. At what value of η will the disc A recoil after the collision; stop; move on? (B and C touch-side by side, a distance ηd apart, and A approaches along their axis of symmetry.)
Solution. From the symmetry of the problem, the velocity of the disc A just after the impact is directed either in the initial direction or opposite to it. Let the velocity of A after the collision be v′, directed to the right. By symmetry, the discs B and C have equal speed v″ in the directions shown. From the geometry, cos θ = (ηd/2)/d = η/2, so sin θ = √(4 − η²)/2 (1).
For the three-disc system, from conservation of linear momentum in the symmetry direction (towards the right): mv = 2mv″ sin θ + mv′, or v = 2v″ sin θ + v′ (2).
From the definition of the coefficient of restitution, for the discs A and B (or C): e = (v″ − v′ sin θ)/(v sin θ − 0). But e = 1 for a perfectly elastic collision, so v sin θ = v″ − v′ sin θ (3).
From (2) and (3): v′ = v(1 − 2sin²θ)/(1 + 2sin²θ) = v(η² − 2)/(6 − η²) [using (1)].
Therefore the disc A will recoil if η < √2 and stop if η = √2. Completed: it will move on in the original direction if η > √2 (v′ > 0 for √2 < η < 2).
Note: one can write the equations of momentum conservation along the direction perpendicular to the initial direction of disc A and the conservation of kinetic energy instead of the equation of restitution.
Teacher's Note: Impulses act along line of centres (angle θ to the axis); use momentum along symmetry axis plus e = 1.
Exam Note: Answer v′ = v(η²−2)/(6−η²); give all three cases.
Question 177. A molecule collides with another, stationary, molecule of the same mass. Demonstrate that the angle of divergence (a) equals 90° when the collision is ideally elastic; (b) differs from 90° when the collision is inelastic.
Solution. (a) Let a molecule with velocity v1 strike another stationary molecule, and just after the collision their velocities become v1′ and v2′ respectively. As the masses are the same, conservation of linear momentum and of kinetic energy for the system respectively give: v1 = v1′ + v2′ and v1² = v1′² + v2′². From the property of vector addition (squaring the first equation and comparing with the second) it is obvious that v1′ ⊥ v2′, or v1′·v2′ = 0.
(b) Due to the loss of kinetic energy in an inelastic collision, v1² > v1′² + v2′², so v1′·v2′ > 0 and therefore the angle of divergence is less than 90°.
Teacher's Note: Squaring the momentum equation gives v1² = v1′² + v2′² + 2v1′·v2′; compare with the energy equation.
Exam Note: Show dot product zero (elastic), positive (inelastic).
Question 178. A rocket ejects a steady jet whose velocity is equal to u relative to the rocket. The gas discharge rate equals μ kg/s. Demonstrate that the rocket motion equation in this case takes the form mw = F − μu, where m is the mass of the rocket at a given moment, w is its acceleration, and F is the external force.
Solution. Suppose that at time t the rocket has mass m and velocity v relative to the reference frame employed. Now consider the inertial frame moving with the velocity that the rocket has at the given moment. In this reference frame, the momentum increment that the rocket and ejected gas system acquires during time dt is dp = m dv + μ dt u = F dt,
or, m dv/dt = F − μu,
or, mw = F − μu.
Teacher's Note: Choose the rocket's instantaneous rest frame so the old rocket momentum is zero; ejected gas carries momentum μu dt.
Exam Note: Equate momentum change to external impulse F dt.
Question 179. A rocket moves in the absence of external forces by ejecting a steady jet with velocity u constant relative to the rocket. Find the velocity v of the rocket at the moment when its mass is equal to m, if at the initial moment it possessed the mass m0 and its velocity was equal to zero. Make use of the formula given in the foregoing problem.
Solution. According to the question, F = 0 and μ = −dm/dt, so the equation for this system becomes m dv/dt = (dm/dt)u. As dv ↑↓ u, m dv = −u dm. Integrating within the limits: (1/u)∫0v dv = −∫m0m dm/m, or v/u = ln(m0/m).
Thus v = u ln(m0/m). As dv ↑↓ u, in vector form v = −u ln(m0/m).
Teacher's Note: Tsiolkovsky equation: speed gain depends only on exhaust speed and mass ratio, not on burn rate.
Exam Note: Answer v = u ln(m0/m); mention direction opposite to u.
Question 180. Find the law according to which the mass of the rocket varies with time, when the rocket moves with a constant acceleration w, the external forces are absent, the gas escapes with a constant velocity u relative to the rocket, and its mass at the initial moment equals m0.
Solution. According to the question, the external force F = 0. So m dv/dt = (dm/dt)u. As dv ↑↓ u, in scalar form m dv = −u dm, or w dt/u = −dm/m. Integrating within the limits for m(t): wt/u = −∫m0m dm/m, or v/u = −ln(m/m0).
Hence m = m0 e−wt/u.
Teacher's Note: Constant acceleration needs exponentially decreasing mass, since dv = w dt must equal −u dm/m.
Exam Note: Answer m = m0 exp(−wt/u).
Part 4 (Q. 181-199)
Question 181. A spaceship of mass m0 moves in the absence of external forces with a constant velocity v0. To change the motion direction, a jet engine is switched on. It starts ejecting a gas jet with velocity u which is constant relative to the spaceship and directed at right angles to the spaceship motion. The engine is shut down when the mass of the spaceship decreases to m. Through what angle α did the motion direction of the spaceship deviate due to the jet engine operation?
Solution. As F = 0, from the equation of dynamics of a body with variable mass: m dv/dt = u dm/dt, or dv = u dm/m (1).
Now dv ↑↓ u and since u ⊥ v, we must have |dv| = v0 dα (because v0 is constant), where dα is the angle by which the spaceship turns in time dt. So −u dm/m = v0 dα, or dα = −(u/v0) dm/m.
Or, α = −(u/v0)∫m0m dm/m = (u/v0) ln(m0/m).
Teacher's Note: Thrust is perpendicular to velocity, so speed stays v0 and only direction turns: dv = v0 dα.
Exam Note: Answer α = (u/v0) ln(m0/m).
Question 182. A cart loaded with sand moves along a horizontal plane due to a constant force F coinciding in direction with the cart's velocity vector. In the process, sand spills through a hole in the bottom with a constant velocity μ kg/s. Find the acceleration and the velocity of the cart at the moment t, if at the initial moment t = 0 the cart with loaded sand had the mass m0 and its velocity was equal to zero. The friction is to be neglected.
Solution. We have dm/dt = −μ, or dm = −μ dt. Integrating, ∫m0m dm = −μ∫0t dt, or m = m0 − μt.
As u = 0 (spilled sand leaves with the velocity of the cart), from the equation of the variable-mass system: (m0 − μt) dv/dt = F, or dv/dt = w = F/(m0 − μt).
Or ∫0v dv = F∫0t dt/(m0 − μt). Hence v = (F/μ) ln[m0/(m0 − μt)].
Teacher's Note: Spilled sand has zero velocity relative to the cart, so no thrust term: m dv/dt = F with m falling.
Exam Note: Give both w(t) and v(t), including the log.
Question 183. A flatcar of mass m0 starts moving to the right due to a constant horizontal force F (Fig. 1.46); sand is loaded onto it from a stationary hopper. The velocity of loading is constant and equal to μ kg/s. Find the time dependence of the velocity and the acceleration of the flatcar in the process of loading. The friction is negligibly small.
Solution. Let the car be moving in a reference frame to which the hopper is fixed and at any instant of time let its mass be m and velocity v. Then from the general equation for a variable-mass system, m dv/dt = F + u dm/dt. We write the equation for our system as m dv/dt = F − v dm/dt, as u = −v (1).
So d(mv)/dt = F and on integration v = Ft/m. But m = m0 + μt, so v = Ft/[m0(1 + μt/m0)].
Thus the sought acceleration is w = dv/dt = F/[m0(1 + μt/m0)²].
Teacher's Note: Falling sand starts at rest in the hopper frame, so net momentum changes only through F: d(mv)/dt = F.
Exam Note: Use d(mv)/dt = F, not m dv/dt = F.
Question 184. A chain AB of length l is located in a smooth horizontal tube so that its fraction of length h hangs freely and touches the surface of the table with its end B (Fig. 1.47). At a certain moment the end A of the chain is set free. With what velocity will this end of the chain slip out of the tube?
Solution. Let the length of the chain inside the smooth horizontal tube at an arbitrary instant be x, and let λ = m/l be the mass per unit length. For the chain inside the tube (u = 0, force along acceleration): λxw = T (1), where T is the tension.
Similarly for the overhanging part: λhw = λhg − T (2).
From (1) and (2): λ(x + h)w = λhg, or (x + h)v dv/ds = hg. As the length of the chain inside the tube decreases with time, ds = −dx, so (x + h)v dv/(−dx) = gh, or v dv = −gh dx/(x + h).
Integrating: ∫0v v dv = −gh∫l−h0 dx/(x + h), or v²/2 = gh ln(l/h), or v = √(2gh ln(l/h)).
Teacher's Note: Energy is not conserved (jerk when links start moving), so use Newton's law for both parts with common tension.
Exam Note: Answer v = √(2gh ln(l/h)); use T common to both parts.
Question 185. The angular momentum of a particle relative to a certain point O varies with time as M = a + bt², where a and b are constant vectors, with a ⊥ b. Find the force moment N relative to the point O acting on the particle when the angle between the vectors N and M equals 45°.
Solution. Force moment relative to point O: N = dM/dt = 2bt. Let the angle between M and N be α = 45° at t = t0. Then 1/√2 = M·N/(|M||N|) = (a + bt0²)·(2bt0)/[√(a² + b²t0⁴)·2bt0] = 2b²t0³/[√(a² + b²t0⁴)·2bt0] = bt0²/√(a² + b²t0⁴).
So 2b²t0⁴ = a² + b²t0⁴, or t0 = √(a/b) (as t0 cannot be negative). It is also obvious from the vector figure (components a and bt²) that the angle α equals 45° when a = bt0², i.e. t0 = √(a/b), and N = 2√(a/b)·b.
Teacher's Note: Torque is dM/dt, along b; 45° between M and b occurs when the a and bt² components are equal.
Exam Note: Answer N = 2√(a/b) b; use a ⊥ b.
Question 186. A ball of mass m is thrown at an angle α to the horizontal with the initial velocity v0. Find the time dependence of the magnitude of the ball's angular momentum vector relative to the point from which the ball is thrown. Find the angular momentum M at the highest point of the trajectory if m = 130 g, α = 45°, and v0 = 25 m/s. The air drag is to be neglected.
Solution. M(t) = r × p = (v0t + ½gt²) × m(v0 + gt) = ½m(v0 × g)t². Since the angle between v0 and g is π/2 + α, |v0 × g| = v0g cos α, and the direction is into the plane (−k). Thus M(t) = mv0gt² cos α/2.
At the maximum height, t = τ/2 = v0 sin α/g, so M(τ/2) = (mv0³/2g) sin²α cos α = 37 kg·m²/s.
Alternate: M(0) = 0, so M(t) = ∫0tNdt = ∫0t(r × mg)dt = ∫0t[(v0t + ½gt²) × mg]dt = (v0 × mg)t²/2.
Teacher's Note: Torque of gravity about launch point is r × mg; the g × g term vanishes, leaving a t² law.
Exam Note: Numerical check: 0.13×25³/(2×9.8)×0.354 ≈ 37.
Question 187. A disc A of mass m sliding over a smooth horizontal surface with velocity v experiences a perfectly elastic collision with a smooth stationary wall at a point O (Fig. 1.48). The angle between the motion direction of the disc and the normal of the wall is equal to α. Find: (a) the points relative to which the angular momentum M of the disc remains constant in this process; (b) the magnitude of the increment of the vector of the disc's angular momentum relative to the point O′ which is located in the plane of the disc's motion at the distance l from the point O.
Solution. (a) The disc experiences gravity, the reaction of the horizontal surface, and the reaction force R of the wall at the moment of impact against it. The first two forces counterbalance each other, leaving only the force R. Its moment relative to any point of the line along which the vector R acts, i.e. along the normal to the wall through O, is equal to zero, and therefore the angular momentum of the disc relative to any of these points does not change in the given process.
(b) During the collision with the wall the position of the disc is the same and equal to rOO′. Obviously the increment in the linear momentum of the ball is Δp = 2mv cos α n. Here, ΔM = rOO′ × Δp = 2mvl cos α n, directed normally, emerging from the plane of the figure. Thus |ΔM| = 2mvl cos α.
Teacher's Note: The wall force acts along the normal, so torque is zero about any point on that normal line.
Exam Note: Answer (b): 2mvl cos α; note only normal momentum reverses.
Question 188. A small ball of mass m suspended from the ceiling at a point O by a thread of length l moves along a horizontal circle with a constant angular velocity ω. Relative to which points does the angular momentum M of the ball remain constant? Find the magnitude of the increment of the vector of the ball's angular momentum relative to the point O picked up during half a revolution.
Solution. (a) The ball is under the influence of the forces T and mg at all moments of time while moving along a horizontal circle. The vertical component of T balances mg, so the net moment of these two about any point becomes zero. The horizontal component of T, which provides the centripetal acceleration of the ball, is directed toward the centre C of the horizontal circle, so its moment about the point C equals zero at all moments of time. Hence the net moment of the forces acting on the ball about point C equals zero, and that is why the angular momentum of the ball is conserved about the centre C of the horizontal circle.
(b) Let α be the angle which the thread forms with the vertical. From the equation of particle dynamics: T cos α = mg and T sin α = mω²l sin α, hence cos α = g/(ω²l) (1).
As |M| is constant in magnitude, from the vector figure |ΔM| = 2M cos α, where M = |Mi| = |Mf| = |r × mv| = mvl (as r ⊥ v). Thus |ΔM| = 2mvl cos α = 2mωl² sin α cos α = (2mgl/ω)√(1 − (g/(ω²l))²) (using (1)).
Teacher's Note: M about O has constant size but rotates with the ball; half a turn reverses its horizontal part.
Exam Note: Use cos α = g/(ω²l); watch v = ωl sin α.
Question 189. A ball of mass m falls down without initial velocity from a height h over the Earth's surface. Find the increment of the ball's angular momentum vector picked up during the time of falling (relative to the point O of the reference frame moving translationally in a horizontal direction with a velocity V). The ball starts falling from the point O. The air drag is to be neglected.
Solution. During the free fall time τ = √(2h/g) the reference point O moves in the horizontal direction (say towards the right) by the distance Vτ. In the translating frame, as M(O) = 0 initially, ΔM = Mf = r × mv = (−Vτ i + h j) × m[gτ j − Vi] = −mVgτ²k + mVh(+k) = −mVg(2h/g)k + mVhk = −mVh k (axes: i along V, j along g). Hence |ΔM| = mVh.
Teacher's Note: In the moving frame the ball also drifts backwards with speed V; its torque about O gives the result.
Exam Note: Answer mVh; choose i along V and j along g.
Question 190. A smooth horizontal disc rotates with a constant angular velocity ω about a stationary vertical axis passing through its centre, the point O. At a moment t = 0 a disc is set in motion from that point with velocity v0. Find the angular momentum M(t) of the disc relative to the point O in the reference frame fixed to the disc. Make sure that this angular momentum is caused by the Coriolis force.
Solution. The Coriolis force is 2mv′ × ω. Here ω is along the z-axis (vertical). The moving disc moves with the constant velocity v0, say along the x-axis. Then the Coriolis force is along the y-axis and has magnitude 2mv0ω. At time t the distance of the centre of the moving disc from O is v0t (along the x-axis). Thus the torque N due to the Coriolis force is N = 2mv0ω·v0t along the z-axis.
Hence, equating this to dM/dt: dM/dt = 2mv0²ωt, or M = mv0²ωt² + constant. The constant is irrelevant and may be put equal to zero since the disc is set in motion from the point O.
This discussion is approximate: the Coriolis force will cause the disc to swerve from straight-line motion and thus cause deviation from the above formula, which will be substantial for large t.
Teacher's Note: Only the Coriolis force has torque about O (centrifugal force is radial), so M = ∫ N dt.
Exam Note: Answer M = mωv0²t²; state it is due to Coriolis force.
Question 191. A particle moves along a closed trajectory in a central field of force where the particle's potential energy U = kr² (k is a positive constant, r is the distance of the particle from the centre O of the field). Find the mass of the particle if its minimum distance from the point O equals r1 and its velocity at the point farthest from O equals v2.
Solution. If ṙ = radial velocity of the particle, then the total energy of the particle at any instant is ½mṙ² + M²/(2mr²) + kr² = E (1), where the second term is the kinetic energy of angular motion about the centre O. Then the extreme values of r are determined by ṙ = 0, which gives the quadratic equation k(r²)² − Er² + M²/(2m) = 0. We get r² = [E ± √(E² − 2M²k/m)]/(2k).
From this we see that E = k(r1² + r2²) (2), where r1 is the minimum distance from O and r2 is the maximum distance (sum of the two roots). At the farthest point, E = ½mv2² + kr2² = k(r1² + r2²), since the radial velocity vanishes there. Hence ½mv2² = kr1², i.e. m = 2kr1²/v2².
Note: Eq. (1) can be derived from the standard expressions for kinetic energy and angular momentum in plane polar coordinates: T = ½mṙ² + ½mr²θ̇², M = mr²θ̇.
Teacher's Note: Turning points are roots of a quadratic in r²; their sum gives E, which links r1 and v2.
Exam Note: Answer m = 2k r1²/v2²; use sum of roots.
Question 192. A small ball is suspended from a point O by a light thread of length l. Then the ball is drawn aside so that the thread deviates through an angle θ from the vertical and set in motion in a horizontal direction at right angles to the vertical plane in which the thread is located. What is the initial velocity that has to be imparted to the ball so that it could deviate through the maximum angle π/2 in the process of motion?
Solution. The swinging sphere experiences two forces: gravity and the tension of the thread. The moment of these forces about the vertical axis through the point of suspension is Nz = 0. Consequently, the angular momentum Mz of the sphere relative to this axis is constant. Thus mv0(l sin θ) = mvl (1), where v is the velocity of the sphere in the position when the thread makes an angle π/2 with the vertical (there the velocity is horizontal and perpendicular to the thread).
Mechanical energy is also conserved, as the tension does no work, being always perpendicular to the velocity. Corrected (the printed Eq. (2) has the potential-energy term on the wrong side): ½mv0² = ½mv² + mgl cos θ (2) (the ball rises by l cos θ).
From (1), v = v0 sin θ; putting into (2): ½v0²(1 − sin²θ) = gl cos θ, i.e. v0² cos²θ = 2gl cos θ. Hence v0 = √(2gl/cos θ).
Teacher's Note: Vertical-axis angular momentum and energy are both conserved; at π/2 the speed is purely azimuthal.
Exam Note: Answer √(2gl/cos θ); ball rises l cos θ.
Question 193. A small body of mass m tied to a non-stretchable thread moves over a smooth horizontal plane. The other end of the thread is being drawn into a hole O (Fig. 1.49) with a constant velocity. Find the thread tension as a function of the distance r between the body and the hole if at r = r0 the angular velocity of the thread is equal to ω0.
Solution. The forces acting on the mass m are gravity mg, the normal reaction N (N = −mg, so their net torque about any fixed point is zero) and the tension T, a central force always directed towards the centre O. Hence the moment of T is also zero about O, and therefore the angular momentum of the particle is conserved about O.
Let the angular velocity of the particle be ω when the separation between hole and particle is r. Then m(ω0r0)r0 = m(ωr)r, or ω = ω0r0²/r².
Now, from the second law of motion for m (radial direction; the constant inward speed makes the radial acceleration zero, so T provides centripetal force): T = F = mω²r. Hence the sought tension F = mω0²r0⁴r/r⁴ = mω0²r0⁴/r³.
Teacher's Note: Central force means constant angular momentum: ω r² = const; tension then equals mω²r.
Exam Note: Answer T = mω0²r0⁴/r³.
Question 194. A light non-stretchable thread is wound on a massive fixed pulley of radius R. A small body of mass m is tied to the free end of the thread. At a moment t = 0 the system is released and starts moving. Find its angular momentum relative to the pulley axle as a function of time t.
Solution. On the given system the weight of the body m is the only force whose moment is effective about the axis of the pulley. Take the sense of rotation of the pulley at an arbitrary instant as the positive sense of the axis of rotation (z-axis). As Mz(0) = 0, ΔMz = Mz(t) = ∫Nzdt. So Mz(t) = ∫0tmgR dt = mgRt.
Teacher's Note: Angular momentum of body plus pulley grows by the external torque mgR per second; axle force has no torque.
Exam Note: Answer M = mgRt for the system.
Question 195. A uniform sphere of mass m and radius R starts rolling without slipping down an inclined plane at an angle α to the horizontal. Find the time dependence of the angular momentum of the sphere relative to the point of contact at the initial moment. How will the obtained result change in the case of a perfectly smooth inclined plane?
Solution. Let the point of contact of the sphere at the initial moment (t = 0) be O. At an arbitrary moment, the forces acting on the sphere are gravity mg, the normal reaction Nr = mg cos α, and static friction fr. The normal reaction and the component mg cos α of gravity both pass through the same line, and the force of static friction passes through the point O, so their moments about O vanish. Hence mg sin α is the only force which has an effective torque about O, and it is given by |N| = mgR sin α, directed normally out of the plane of the figure.
As M(t = 0) = 0, ΔM = M(t) = ∫Ndt. Hence M(t) = Nt = mgR sin α · t.
Completed (the printed solution does not state the smooth-plane case): friction produced no torque about O in any case, so on a perfectly smooth plane the torque, and hence M(t) = mgRt sin α, is unchanged (although the motion itself is different: the sphere slides without rotating about its centre).
Teacher's Note: Take the fixed initial contact point: friction and normal force have no torque; only mg sin α acts.
Exam Note: Answer mgRt sin α; unchanged for smooth plane.
Question 196. A certain system of particles possesses a total momentum p and an angular momentum M relative to a point O. Find its angular momentum M′ relative to a point O′ whose position with respect to the point O is determined by the radius vector r0. Find out when the angular momentum of the system of particles does not depend on the choice of the point O.
Solution. Let the position vectors of the particles of the system be ri and ri′ with respect to the points O and O′ respectively. Then ri = ri′ + r0 (1), where r0 is the radius vector of O′ with respect to O.
The angular momentum of the system relative to O is M = Σ(ri × pi) = Σ(ri′ × pi) + Σ(r0 × pi) [using (1)], or M = M′ + (r0 × p), where p = Σpi (2).
Hence M′ = M − r0 × p. From (2), if the total linear momentum of the system p = 0, then its angular momentum does not depend on the choice of the point O. Note that in the C.M. frame the system of particles as a whole is at rest.
Teacher's Note: Shifting origin adds r0 × p; vanishes only when total momentum is zero (C.M. frame).
Exam Note: Answer M′ = M − r0×p; independent when p = 0.
Question 197. Demonstrate that the angular momentum M of the system of particles relative to a point O of the reference frame K can be represented as M = M̃ + [rCp], where M̃ is its proper angular momentum (in the reference frame moving translationally and fixed to the centre of inertia), rC is the radius vector of the centre of inertia relative to the point O, and p is the total momentum of the system of particles in the reference frame K.
Solution. On the basis of the solution of problem 1.196, in the C.M. frame the angular momentum of a system of particles is independent of the choice of the point relative to which it is determined; in accordance with the problem, this is denoted by M̃. We denote the angular momentum of the system relative to the point O by M. Since the proper angular momentum M̃ in the C.M. frame does not depend on the choice of the point O′, this point may be taken to coincide with the point O of the K-frame at a given moment of time. Then at that moment the radius vectors of all the particles in both reference frames are equal (ri′ = ri) and the velocities are related by vi = ṽi + vC (1), where vC is the velocity of the C.M. frame relative to the K-frame. Consequently,
M = Σmi(ri × vi) = Σmi(ri′ × ṽi) + Σmi(ri × vC),
or M = M̃ + m(rC × vC), as Σmiri = mrC, where m = Σmi.
Or M = M̃ + (rC × mvC) = M̃ + (rC × p).
Teacher's Note: Angular momentum = spin about centre of mass plus orbital part r_C × p.
Exam Note: Split v = ṽ + v_C; use Σm r = m r_C.
Question 198. A ball of mass m moving with velocity v0 experiences a head-on elastic collision with one of the spheres of a stationary rigid dumbbell as shown in Fig. 1.50 (the ball moves along the line perpendicular to the dumbbell axis and hits sphere 1). The mass of each sphere equals m/2, and the distance between them is l. Disregarding the size of the spheres, find the proper angular momentum M̃ of the dumbbell after the collision, i.e. the angular momentum in the reference frame moving translationally and fixed to the dumbbell's centre of inertia.
Solution. From conservation of linear momentum along the direction of the incident ball for the system consisting of the colliding ball and sphere 1: mv0 = mv′ + (m/2)v1 (1), where v′ and v1 are the velocities of the ball and sphere 1 after the collision (the collision is head-on).
As the collision is perfectly elastic, from the coefficient of restitution, 1 = (v′ − v1)/(0 − v0), or v′ − v1 = −v0 (2).
Solving (1) and (2): v1 = 4v0/3, directed towards the right.
In the C.M. frame of spheres 1 and 2: p̃1 = −p̃2 and |p̃1| = |p̃2| = μ|v1 − v2| = (m/4)(4v0/3) = mv0/3. Also r1C = −r2C, thus M̃ = 2[r1C × p̃1]. As r1C ⊥ p̃1, M̃ = 2[(l/2)(mv0/3)]n, where n is the unit vector in the sense of r1C × p̃1.
Hence M̃ = mv0l/3.
Teacher's Note: Only sphere 1 is hit, so the dumbbell gains momentum and spin about its C.M.
Exam Note: Answer mv0 l/3; solve momentum plus restitution first.
Question 199. Two small identical discs, each of mass m, lie on a smooth horizontal plane. The discs are interconnected by a light non-deformed spring of length l0 and stiffness κ. At a certain moment one of the discs is set in motion in a horizontal direction perpendicular to the spring with velocity v0. Find the maximum elongation of the spring in the process of motion, if it is known to be considerably less than unity (i.e. much smaller than l0).
Solution. In the C.M. frame of the system (both discs + spring) the linear momenta of the discs are related by p̃1 = −p̃2 at all moments of time, where p̃1 = p̃2 = p̃ = μvrel, and the total kinetic energy of the system is T̃ = ½μvrel² [see solution of 1.147 (b)]; here μ = m/2. At the moment of maximum deformation of the spring the projection of vrel along the length of the spring becomes zero, i.e. vrel(x) = 0.
The conservation of mechanical energy of the system in the C.M. frame gives ½(m/2)v0² = ½κx² + ½(m/2)vrel(y)² (1), where x is the elongation.
From the conservation of angular momentum of the system about the C.M. (μv0l0 = μvrel(y)(l0 + x)): (m/2)v0l0 = (m/2)vrel(y)(l0 + x), or vrel(y) = v0l0/(l0 + x) = v0(1 + x/l0)−1 ≈ v0(1 − x/l0), as x << l0 (2).
Using (2) in (1): ½mv0²[1 − (1 − x/l0)²] = κx², or ½mv0²[1 − (1 − 2x/l0 + x²/l0²)] = κx², or mv0²x/l0 ≈ κx² [neglecting x²/l0²].
As x ≠ 0, x = mv0²/(κl0).
Teacher's Note: Use the C.M. frame: energy and angular momentum conservation; at maximum stretch only tangential relative velocity remains.
Exam Note: Answer x = mv0²/(κ l0); small-x expansion stated.
Step-by-Step IE Irodov Solutions for JEE Math
Complete Math Solutions for IE Irodov Solutions Chapter 3 Laws Of Conservation Of Energy Momentum And Angular Momentum Part 2
Access the complete chapter-wise PDF for IE Irodov Solutions Chapter 3 Laws Of Conservation Of Energy Momentum And Angular Momentum Part 2. These structured IE Irodov Solutions solutions for JEE Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Detailed Calculation Guides for JEE
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Explore More Study Resources for JEE Math
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.