Step-by-Step IE Irodov Solutions for JEE Physics Chapter 05 Dynamics Of A Solid Body
Review structured textbook solutions for JEE Physics Chapter 05 Dynamics Of A Solid Body prepared by IE Irodov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Download Chapter 05 Dynamics Of A Solid Body Textbook Solutions PDF
View or download the dedicated Chapter 05 Dynamics Of A Solid Body solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Physics.
Dynamics Of A Solid Body - Problems 260 to 289
Dynamics Of A Solid Body (Part - 2)
Question 260. A uniform solid cylinder A of mass m1 can freely rotate about a horizontal axis fixed to a mount B of mass m2 (Fig. 1.66). A constant horizontal force F is applied to the end K of a light thread tightly wound on the cylinder. The friction between the mount and the supporting horizontal plane is assumed to be absent. Find: (a) the acceleration of the point K; (b) the kinetic energy of this system t seconds after the beginning of motion.
Solution. (a) For the translational motion of the system (m1 + m2), F = (m1 + m2)wc, so wc = F/(m1 + m2). (1)
For the rotational motion of the cylinder, Ncz = Icβz: Fr = (m1r2/2)β, so βr = 2F/m1. (2)
But wK = wc + βr, so
wK = F/(m1 + m2) + 2F/m1 = F(3m1 + 2m2)/[m1(m1 + m2)]. (3)
(b) From ΔT = Aext with ΔT = T(t): T(t) = Aext = Fx, where x is the displacement of the point of application of F in time t.
= F(½wKt2) = F2t2(3m1 + 2m2)/[2m1(m1 + m2)] (using Eq. 3).
Alternate: T(t) = Ttranslation + Trotation = ½(m1 + m2)[Ft/(m1 + m2)]2 + ½(m1r2/2)(2Ft/(m1r))2 = F2t2(3m1 + 2m2)/[2m1(m1 + m2)].
Teacher's Note: Thread point K accelerates as mount plus rim, wK = wc + βr; energy equals work F·x.
Exam Note: Work-energy shortcut earns marks; note K's displacement exceeds the centre's.
Question 261. A plank of mass m1 with a uniform sphere of mass m2 placed on it rests on a smooth horizontal plane. A constant horizontal force F is applied to the plank. With what accelerations will the plank and the centre of the sphere move provided there is no sliding between the plank and the sphere?
Solution. Take x and φ positive as in the figure. For the sphere, Fx = mwcx and Ncz = Icβz give fr = m2w2 and frr = (2/5)m2r2β (w2 is the acceleration of the centre of the sphere).
For the plank: F − fr = m1w1.
The no-slipping condition gives w1 = w2 + βr.
Solving the four equations: w1 = F/(m1 + (2/7)m2) and w2 = (2/7)w1.
Teacher's Note: No slipping links accelerations: plank = sphere centre + βr; friction drives both translation and spin of the sphere.
Exam Note: Write four equations (two per body) plus the kinematic constraint.
Question 262. A uniform solid cylinder of mass m and radius R is set in rotation about its axis with an angular velocity ω0, then lowered with its lateral surface onto a horizontal plane and released. The coefficient of friction between the cylinder and the plane is equal to k. Find: (a) how long the cylinder will move with sliding; (b) the total work performed by the sliding friction force acting on the cylinder.
Solution. (a) Take x and φ positive as in the figure. From Fx = mwcx and Ncz = Icβz:
kmg = mwcx, so wcx = kg (1)
−kmgR = (mR2/2)βz, so βz = −2kg/R (2)
Let pure rolling start at t = t0. From ωz = ω0z + βzt: ω = ω0 − 2(kg/R)t. (3)
From vcx = v0cx + wcxt: vc = 0 + kgt0.
At t = t0, vc = ωR, so kgt0 = (ω0 − 2kgt0/R)R, thus t0 = ω0R/(3kg).
(b) The work of friction is Afr = kmg[½wct02 − (ω0t0 + ½βt02)R], where the first term is the forward displacement of the centre and the second the backward slip of the contact point; with the values above
Afr = kmg(ω0R/3kg)[ω0R/6 + ω0R/3 − ω0R] = −mω02R2/6.
The same result follows from the work-energy theorem, Afr = ΔT.
Teacher's Note: Sliding ends when vc = ωR; friction work is negative, equal to the loss of kinetic energy.
Exam Note: Check by ΔT = ¾mv² − ¼mR²ω02.
Question 263. A uniform ball of radius r rolls without slipping down from the top of a sphere of radius R. Find the angular velocity of the ball at the moment it breaks off the sphere. The initial velocity of the ball is negligible.
Solution. At the moment of breaking off, the equation of motion of the centre of the ball is mv2/(R + r) = mg cos θ, where v is the velocity of the centre at that moment and θ the corresponding angle. From energy conservation: mgh = ½mv2 + ½Iω2, where I = (2/5)mr2. In addition, v = ωr and h = (R + r)(1 − cos θ).
From these four equations: ω = √[10g(R + r)/17]/r, i.e. ω = √(10g(R + r)/(17r2)).
Corrected: the printed final expression had its fraction bar missing (illegible); the form above was re-derived (cos θ = 10/17, v2 = 10g(R + r)/17).
Teacher's Note: Break-off when normal reaction vanishes; rolling adds ½Iω² = (1/5)mv².
Exam Note: Combine radial equation with energy; centre moves on radius R + r.
Question 264. A uniform solid cylinder of radius R = 15 cm rolls over a horizontal plane passing into an inclined plane forming an angle α = 30° with the horizontal (Fig. 1.67). Find the maximum value of the velocity v0 which still permits the cylinder to roll onto the inclined plane section without a jump. The sliding is assumed to be absent.
Solution. Since the cylinder moves without sliding, it rotates about the point O of the common edge of the planes; O is the foot of the instantaneous axis of rotation. At an instant when the velocity of the centre is v1 and the angle (see figure) is β:
mv12/R = mg cos β − N, or v12 = gR cos β − NR/m. (1)
Energy conservation: ½I0v12/R2 − ½I0v02/R2 = mgR(1 − cos β), with I0 = mR2/2 + mR2 = (3/2)mR2 (parallel-axis theorem).
Thus v12 = v02 + (4/3)gR(1 − cos β). (2)
From (1) and (2): v02 = (gR/3)(7 cos β − 4) − NR/m.
The angle β is smaller than or equal to α, so putting β = α: v02 = (gR/3)(7 cos α − 4) − N0R/m, where N0 is the corresponding reaction. Note N ≥ N0. No jump occurs if N0 > 0. Hence v0 must be less than
vmax = √[(gR/3)(7 cos α − 4)] (≈ 1.0 m/s for R = 15 cm, α = 30°).
Teacher's Note: Cylinder pivots about the edge; jump-off when the edge reaction N falls to zero at β = α.
Exam Note: Take I about the edge; set N = 0.
Question 265. A small body A is fixed to the inside of a thin rigid hoop of radius R and mass equal to that of the body A. The hoop rolls without slipping over a horizontal plane; at the moments when the body A gets into the lower position, the centre of the hoop moves with velocity v0 (Fig. 1.68). At what values of v0 will the hoop move without bouncing?
Solution. The tendency to bounce is greatest when the body A is at the highest point of the hoop. Let the velocity of the centre of the hoop be v at that position. Static friction does no work, so by conservation of mechanical energy (E1 = E2):
0 + ½mv02 + ½mR2(v0/R)2 − mgR = ½m(2v)2 + ½mv2 + ½mR2(v/R)2 + mgR,
or 3v2 = v02 − 2gR. (1)
For the body at the top: mg + N′ = mω2R = m(v/R)2R. (2)
The hoop has no vertical acceleration, so N + N′ = mg. (3)
From (2) and (3): N = 2mg − mv2/R. (4)
The hoop does not bounce if N ≥ 0. (5)
From (1), (4), (5): (8gR − v02)/(3R) ≥ 0, i.e. 8gR ≥ v02. Hence v0 ≤ √(8gR).
Teacher's Note: Worst case: body at the top, where it presses the hoop upward; bounce when ground reaction N turns zero.
Exam Note: Energy equation, then N ≥ 0 gives v0 ≤ √(8gR).
Dynamics Of A Solid Body (Part - 3)
Question 266. Determine the kinetic energy of a tractor crawler belt of mass m if the tractor moves with velocity v (Fig. 1.69).
Solution. Since the lower part of the belt is in contact with the rigid floor, its velocity is zero. The tractor moves with velocity v, hence the velocity of the upper part of the belt is 2v by the rolling condition, and the kinetic energy of the upper part = ½(m/2)(2v)2 = mv2, which is also the sought kinetic energy, assuming that the length of the belt is much larger than the radius of the wheels.
Teacher's Note: Lower belt at rest, upper belt at 2v, each half of the mass; wheel-end parts neglected.
Exam Note: Answer mv²; give the 2v argument.
Question 267. A uniform sphere of mass m and radius r rolls without sliding over a horizontal plane, rotating about a horizontal axle OA (Fig. 1.70). In the process, the centre of the sphere moves with velocity v along a circle of radius R. Find the kinetic energy of the sphere.
Solution. The sphere has two motions: rotation about its own axis and motion in a circle of radius R. Hence T = ½I1ω12 + ½I2ω22 (1), where I1 is the moment of inertia about its own axis and I2 that about the vertical axis through O.
I1 = (2/5)mr2 and I2 = (2/5)mr2 + mR2 (parallel-axis theorem). (2)
ω1 = v/r and ω2 = v/R. (3)
Using (2) and (3) in (1): T = (7/10)mv2(1 + 2r2/(7R2)).
Teacher's Note: Kinetic energy = spin about own axis + revolution about the vertical axis through O.
Exam Note: Add both rotations; parallel-axis theorem for I about the vertical axis.
Question 268. Demonstrate that in the reference frame rotating with a constant angular velocity ω about a stationary axis a body of mass m experiences the resultant (a) centrifugal force of inertia Fcf = mω2Rc, where Rc is the radius vector of the body's centre of inertia relative to the rotation axis; (b) Coriolis force Fcor = 2m[v′cω], where v′c is the velocity of the body's centre of inertia in the rotating reference frame.
Solution. For a point mass dm, seen from the rotating frame, the equation is dm w′ = f + dm ω2r′ + 2dm(v′ × ω), where r′ is the radius vector in the rotating frame with respect to the rotation axis and v′ the velocity in the same frame.
The total centrifugal force is Fcf = Σ dm ω2r′ = mω2Rc, where Rc is the radius vector of the centre of mass with respect to the rotation axis; also Fcor = 2m v′c × ω, where we have used the definitions mRc = Σ dm r′ and mv′c = Σ dm v′.
Teacher's Note: Both forces are linear in r′ and v′, so summing over elements uses the centre-of-mass definitions.
Exam Note: State the element force, then sum using mRc = Σ dm r′.
Question 269. A midpoint of a thin uniform rod AB of mass m and length l is rigidly fixed to a rotation axle OO′ as shown in Fig. 1.71. The rod is set into rotation with a constant angular velocity ω. Find the resultant moment of the centrifugal forces of inertia relative to the point C in the reference frame fixed to the axle OO′ and to the rod.
Solution. Consider a small element of length dx at a distance x from the point C; it rotates in a circle of radius r = x sin θ. Its mass is (m/l)dx, so the centrifugal force on it is (m/l)dx ω2x sin θ, and its moment about C is
|dN| = (m/l)dx ω2x sin θ · x cos θ = (mω2/2l) sin 2θ x2dx.
Hence the total moment N = 2∫0l/2 (mω2/2l) sin 2θ x2dx = (1/24)mω2l2 sin 2θ.
Teacher's Note: Moment arm of each element's force about C is x cos θ; integrate over both halves of the rod.
Exam Note: Show element, then integrate 0 to l/2, double.
Question 270. A conical pendulum, a thin uniform rod of length l and mass m, rotates uniformly about a vertical axis with angular velocity ω (the upper end of the rod is hinged). Find the angle θ between the rod and the vertical.
Solution. Consider the system in a frame rotating with the rod. In this frame the rod is at rest and experiences, besides the gravitational force mg and the reaction force R, the centrifugal force Fcf. From the equilibrium condition (net moment about O is zero): Ncf = mg(l/2) sin θ. (1)
Here Ncf is the moment of the centrifugal force about O. Take an element of length dx at distance x from O; it experiences a horizontal pseudo force (m/l)dx ω2x sin θ. Its moment about O is
dNcf = (m/l)dx ω2x sin θ · x cos θ = (mω2/l) sin θ cos θ x2dx.
So Ncf = ∫0l (mω2/l) sin θ cos θ x2dx = (mω2l2/3) sin θ cos θ. (2)
From (1) and (2): cos θ = 3g/(2ω2l), or θ = cos−1(3g/(2ω2l)).
Teacher's Note: Torque balance about the hinge in the rotating frame: gravity moment against integrated centrifugal moment.
Exam Note: Integrate element moments; sin θ cancels, leaving cos θ.
Question 271. A uniform cube with edge a rests on a horizontal plane whose friction coefficient equals k. The cube is set in motion with an initial velocity, travels some distance over the plane and comes to a stand-still. Explain the disappearance of the angular momentum of the cube relative to the axis lying in the plane at right angles to the cube's motion direction. Find the distance between the resultants of gravitational forces and the reaction forces exerted by the supporting plane.
Solution. When the cube is given an initial velocity on the table it acquires an angular momentum about an axis on the table perpendicular to the initial velocity (just below the centre of gravity). This angular momentum disappears when the cube stops, which can only be due to a torque. Frictional forces cannot do this by themselves because they act in the plane containing the axis. But if the normal reaction acts eccentrically, its torque can bring about the vanishing of the angular momentum.
The distance Δx between the point of application of the normal reaction and the centre of gravity is found by taking moments of all forces about the centre of gravity; this must vanish because the cube does not turn or tumble. With friction fr: fr·(a/2) = NΔx. But N = mg and fr = kmg, so Δx = ka/2.
Teacher's Note: Friction lies in the axis plane, so the shifted normal reaction supplies the torque that removes angular momentum.
Exam Note: Moments about the centre: kmg·a/2 = mg·Δx.
Question 272. A smooth uniform rod AB of mass M and length l rotates freely with an angular velocity ω0 in a horizontal plane about a stationary vertical axis passing through its end A. A small sleeve of mass m starts sliding along the rod from the point A. Find the velocity v′ of the sleeve relative to the rod at the moment it reaches its other end B.
Solution. In the motion of the system the kinetic energy and the angular momentum about the rotation axis do not vary. Hence
½(Ml2/3)ω02 = ½m(ω2l2 + v′2) + ½(Ml2/3)ω2 (ω is the final angular velocity of the rod),
and (Ml2/3)ω0 = (Ml2/3)ω + ml2ω.
From these equations: ω = ω0/(1 + 3m/M) and v′ = ω0l/√(1 + 3m/M).
Corrected: the printed expression for ω read ω0/(1 + 3M/M), a misprint; re-derived from the two equations above, the correct form is ω0/(1 + 3m/M).
Teacher's Note: Smooth rod: energy and angular momentum about the axis are both conserved; sleeve has radial and tangential speed.
Exam Note: Solve the two conservation equations; ω first, then v′.
Question 273. A uniform rod of mass m = 5.0 kg and length l = 90 cm rests on a smooth horizontal surface. One of the ends of the rod is struck with the impulse J = 3.0 N·s in a horizontal direction perpendicular to the rod. As a result, the rod obtains the momentum p = 3.0 N·s. Find the force with which one half of the rod will act on the other in the process of motion.
Solution. Due to the impulse, the angular impulse received by the rod about the C.M. is p·l/2. If ω is the angular velocity acquired by the rod, (ml2/12)ω = pl/2, or ω = 6p/(ml). (1)
In the frame of the C.M. the rod rotates about an axis through its midpoint with angular velocity ω. The force exerted by one half on the other = mass of one half × acceleration of the C.M. of that half in this frame = (m/2)(ω2l/4) = mω2l/8 = 9p2/(2ml) = 9 N.
Teacher's Note: Angular impulse about the centre gives ω; each half's centre moves in a circle of radius l/4.
Exam Note: Substitute p, m, l: 9 N.
Question 274. A thin uniform square plate with side l and mass M can rotate freely about a stationary vertical axis coinciding with one of its sides. A small ball of mass m flying with velocity v at right angles to the plate strikes elastically the centre of it. Find: (a) the velocity of the ball v′ after the impact; (b) the horizontal component of the resultant force which the axis will exert on the plate after the impact.
Solution. (a) During the impact the kinetic energy and the angular momentum about the rotation axis do not vary:
½mv2 = ½mv′2 + ½(Ml2/3)ω2 and mv(l/2) = mv′(l/2) + (Ml2/3)ω.
From these equations: v′ = [(3m − 4M)/(3m + 4M)]v and ω = 4v/[l(1 + 4M/3m)].
As v′ ↑↑ v, in vector form v′ = [(3m − 4M)/(3m + 4M)]v.
(b) The sought force provides the centripetal acceleration of the C.M. of the plate: Fn = Mwcn = Mω2(l/2) = 8Mv2/[l(1 + 4M/3m)2].
Teacher's Note: Elastic impact: both kinetic energy and angular momentum about the axis conserved; axis force gives centripetal pull.
Exam Note: Sign of v′ depends on 3m versus 4M.
Question 275. A vertically oriented uniform rod of mass M and length l can rotate about its upper end. A horizontally flying bullet of mass m strikes the lower end of the rod and gets stuck in it; as a result, the rod swings through an angle α. Assuming that m << M, find: (a) the velocity of the flying bullet; (b) the momentum increment in the system "bullet-rod" during the impact; what causes the change of that momentum; (c) at what distance x from the upper end of the rod the bullet must strike for the momentum of the system "bullet-rod" to remain constant during the impact.
Solution. (a) About the axis of rotation the angular momentum of the system is conserved. With v the bullet velocity: mvl = (ml2 + Ml2/3)ω, so ω = mv/[(m + M/3)l] ≈ 3mv/(Ml) as m << M. (1)
Energy conservation for the rod with bullet in the gravitational field: ½(ml2 + Ml2/3)ω2 = (M + m)g(l/2)(1 − cos α) (2) [the C.M. of the rod rises by (l/2)(1 − cos α)].
Solving (1) and (2): v = (M/m)√(2gl/3) sin(α/2) and ω = √(6g/l) sin(α/2).
(b) Δp = [m(ωl) + M(ωl/2)] − mv, where ωl is the velocity of the bullet and ωl/2 the velocity of the C.M. of the rod after the impact. Putting the values of v and ω: Δp ≈ ½mv = M√(gl/6) sin(α/2).
This change is caused by the reaction at the hinge on the upper end.
(c) If the bullet strikes at distance x: mvx = (Ml2/3 + mx2)ω′, so ω′ ≈ 3mvx/(Ml2). Final momentum pf = mxω′ + ∫0l yω′(M/l)dy = (M/2)ω′l = (3/2)mv(x/l).
So Δp = pf − pi = mv(3x/(2l) − 1). This vanishes for x = (2/3)l.
Teacher's Note: Angular momentum is conserved in the impact, energy afterwards; hinge reaction changes linear momentum.
Exam Note: Hinge impulse vanishes at the centre of percussion, x = 2l/3.
Question 276. A horizontally oriented uniform disc of mass M and radius R rotates freely about a stationary vertical axis passing through its centre. The disc has a radial guide along which can slide without friction a small body of mass m. A light thread running down through the hollow axle of the disc is tied to the body. Initially the body was located at the edge of the disc and the whole system rotated with an angular velocity ω0. Then by means of a force F applied to the lower end of the thread the body was slowly pulled to the rotation axis. Find: (a) the angular velocity of the system in its final state; (b) the work performed by the force F.
Solution. (a) As the force F on the body is radial, its moment about the axis is zero, so the angular momentum of the system about the axis is conserved: (MR2/2)ω0 + mω0R2 = (MR2/2)ω, or ω = ω0(1 + 2m/M).
(b) From ΔT = Aext: ½(MR2/2)ω2 − ½(MR2/2 + mR2)ω02 = Aext. Putting the value of ω from part (a) and solving: Aext = (mω02R2/2)(1 + 2m/M).
Teacher's Note: Radial force exerts no torque about the axis, so angular momentum is conserved; work equals rise in KE.
Exam Note: Final body sits on the axis, contributing no moment of inertia.
Question 277. A man of mass m1 stands on the edge of a horizontal uniform disc of mass m2 and radius R which is capable of rotating freely about a stationary vertical axis passing through its centre. At a certain moment the man starts moving along the edge of the disc; he shifts over an angle φ′ relative to the disc and then stops. In the process of motion the velocity of the man varies with time as v′(t). Assuming the dimensions of the man to be negligible, find: (a) the angle through which the disc had turned by the moment the man stopped; (b) the force moment (relative to the rotation axis) with which the man acted on the disc in the process of motion.
Solution. (a) Let z be the rotation axis of the disc and φ its rotation angle (right-hand screw rule; φ and φ′ are measured in the same sense algebraically). The angular momentum Mz of the system (disc + man) is conserved and initially zero, so at any instant
0 = (m2R2/2)(dφ/dt) + m1[(dφ′/dt)R + (dφ/dt)R]R,
or dφ = −[m1/(m1 + m2/2)]dφ′.
Integrating: φ = −[m1/(m1 + m2/2)]φ′. (1)
This gives the total angle of rotation of the disc.
(b) From (1): dφ/dt = −[m1/(m1 + m2/2)]dφ′/dt = −[m1/(m1 + m2/2)]v′(t)/R. Differentiating: d2φ/dt2 = −[m1/(m1 + m2/2)](1/R)dv′(t)/dt.
The sought moment from Nz = Iβz: Nz = (m2R2/2)d2φ/dt2 = −(m2R2/2)[m1/(m1 + m2/2)](1/R)dv′/dt.
Hence Nz = −[m1m2R/(2m1 + m2)] dv′(t)/dt.
Teacher's Note: Zero total angular momentum: man's absolute angular speed is φ′ plus disc's φ, so the disc turns backwards.
Exam Note: Disc turns opposite to the man; torque on the disc = I·β.
Question 278. Two horizontal discs rotate freely about a vertical axis passing through their centres. The moments of inertia of the discs relative to this axis are equal to I1 and I2, and the angular velocities to ω1 and ω2. When the upper disc fell on the lower one, both discs began rotating, after some time, as a single whole (due to friction). Find: (a) the steady-state angular rotation velocity of the discs; (b) the work performed by the friction forces in this process.
Solution. (a) From conservation of angular momentum about the vertical axis z: I1ω1z + I2ω2z = (I1 + I2)ωz. (1)
Hence ωz = (I1ω1z + I2ω2z)/(I1 + I2). For ωz > 0 the vector ω points along the positive z axis, and vice versa. As both discs rotate about the same vertical axis, in vector form ω = (I1ω1 + I2ω2)/(I1 + I2). The problem makes sense only if ω1 ↑↑ ω2 or ω1 ↑↓ ω2.
(b) From Afr = ΔT: Afr = ½(I1 + I2)ωz2 − ½I1ω1z2 − ½I2ω2z2. Using Eq. (1): Afr = −[I1I2/(2(I1 + I2))](ω1z − ω2z)2.
Note: the printed energy line had a sign misprint (+½I2ω2z2); the form above is the correct one and gives the printed final result.
Teacher's Note: Friction is internal: angular momentum conserved, kinetic energy lost equals μ-type loss ∝ (ω₁−ω₂)².
Exam Note: Use signed components; opposite spins give ω₁z − ω₂z large.
Question 279. A small disc and a thin uniform rod of length l, whose mass is η times greater than the mass of the disc, lie on a smooth horizontal plane. The disc is set in motion, in horizontal direction and perpendicular to the rod, with velocity v, after which it elastically collides with the end of the rod. Find the velocity of the disc and the angular velocity of the rod after the collision. At what value of η will the velocity of the disc after the collision be equal to zero? reverse its direction?
Solution. For the closed system (disc + rod) the angular momentum is conserved about any axis. Taking the axis through the C.M. of the rod, with m the mass of the disc: mv(l/2) = mv′(l/2) + (ηml2/12)ω (1), where v′ is the final velocity of the disc and ω the angular velocity of the rod.
Linear momentum is also conserved: with vc = lω/6 (velocity of the rod's C.M.), v − v′ = ηvc. (2)
The collision is elastic, so ½mv2 = ½mv′2 + ½ηmvc2 + ½(ηml2/12)ω2 (3), or v2 − v′2 = 4ηvc2, and hence v + v′ = 4vc.
Then v′ = [(4 − η)/(4 + η)]v and ω = 12v/[(4 + η)l].
Vectorially, taking v′ parallel to v: u′ = [(4 − η)/(4 + η)]v. So u′ = 0 for η = 4 and u′ ↑↓ v (direction reversed) for η > 4.
Note: vc = lω/6 follows from (1) and (2) and is consistent with the final results; the printed relation was hard to read.
Teacher's Note: Three conservation laws (linear, angular, energy) give three equations for v′, vc, ω.
Exam Note: Disc stops at η = 4; reverses for η > 4.
Question 280. A stationary platform P which can rotate freely about a vertical axis (Fig. 1.72) supports a motor M and a balance weight N. The moment of inertia of the platform with the motor and the balance weight relative to this axis is equal to I. A light frame is fixed to the motor's shaft with a uniform sphere A rotating freely with an angular velocity ω0 about a shaft BB′ coinciding with the axis OO′. The moment of inertia of the sphere relative to the rotation axis is equal to I0. Find: (a) the work performed by the motor in turning the shaft BB′ through 90°; through 180°; (b) the moment of external forces which maintains the axis of the arrangement in the vertical position after the motor turns the shaft BB′ through 90°. (Fig. 1.72: platform P on the vertical axis OO′ carries the motor M and balance weight N; sphere A in a frame sits on the motor shaft BB′ along OO′.)
Solution. (a) When the shaft BB′ is turned through 90° the platform must start turning with angular velocity Ω so that the angular momentum remains constant: (I + I0)Ω = I0ω0, or Ω = I0ω0/(I + I0). The work performed by the motor is therefore ½(I + I0)Ω2 = ½I02ω02/(I + I0).
If the shaft is turned through 180°, the angular velocity of the sphere changes sign. From conservation of angular momentum: IΩ − I0ω0 = I0ω0 (here −I0ω0 is the complete angular momentum of the sphere, i.e. its angular velocity is now −ω0). Then Ω = 2I0ω0/I and the work done is ½IΩ2 + ½I0ω02 − ½I0ω02 = 2I02ω02/I.
(b) In case (a), first part, the angular momentum vector of the sphere precesses with angular velocity Ω. Thus a torque I0ω0Ω = I02ω02/(I + I0) is needed.
Note: the printed statement gave the sphere's moment of inertia as I, which is a misprint for I0 (the solution uses I0).
Teacher's Note: Turning the spin axis transfers angular momentum to the platform; motor work equals kinetic energy gained.
Exam Note: After 180° spin reverses, so Ω doubles; torque = L·Ω.
Dynamics Of A Solid Body (Part - 4)
Question 281. A horizontally oriented uniform rod AB of mass m = 1.40 kg and length l0 = 100 cm rotates freely about a stationary vertical axis OO′ passing through its end A. The point A is located at the middle of the axis OO′ whose length is equal to l = 55 cm. At what angular velocity of the rod is the horizontal component of the force acting on the lower end of the axis OO′ equal to zero? What is in this case the horizontal component of the force acting on the upper end of the axis?
Solution. The total centrifugal force on the rod is ∫0l0(m/l0)ω2x dx = ½ml0ω2. Let T1 and T2 be the horizontal forces on the lower and upper ends of the axis (equal and opposite to the rod's reactions, as in the figure). For equilibrium in the rotating frame: (T2 − T1)(l/2) = mg(l0/2) and T2 + T1 = ½ml0ω2.
Thus T1 vanishes when ω2 = 2g/l, i.e. ω = √(2g/l) = 6 rad/s. Then T2 = mg(l0/l) = 25 N.
Teacher's Note: Rotating frame: centrifugal force at mid-length and weight's moment about A must balance via axis reactions.
Exam Note: Two equations, T₁ = 0 gives ω; numbers: 6 rad/s, 25 N.
Question 282. The middle of a uniform rod of mass m and length l is rigidly fixed to a vertical axis OO′ so that the angle between the rod and the axis is equal to θ (see Fig. 1.71). The ends of the axis OO′ are provided with bearings. The system rotates without friction with an angular velocity ω. Find: (a) the magnitude and direction of the rod's angular momentum M relative to the point C, as well as its angular momentum relative to the rotation axis; (b) how much the modulus of the vector M relative to the point C increases during a half-turn; (c) the moment of external forces N acting on the axle OO′ in the process of rotation.
Solution. (a) The angular velocity ω about OO′ can be resolved into a component parallel to the rod and a component ω sin θ perpendicular to the rod through C. The parallel component does not contribute, so the angular momentum M = Iω sin θ = (1/12)ml2ω sin θ, directed perpendicular to the rod (in the plane of rod and axis). Also Mz = M sin θ = (1/12)ml2ω sin2θ. As the rod turns, M sweeps out a cone about the axis (half-angle 90° − θ).
(b) The modulus of M does not change; the modulus of the change of the vector M in a half-turn is |ΔM| = 2M sin(90° − θ) = (1/12)ml2ω sin 2θ.
(c) Here M⊥ = M cos θ = Iω sin θ cos θ. Since M precesses with angular velocity ω, |dM/dt| = Iω sin θ cos θ · ω = (1/24)ml2ω2 sin 2θ, which is the moment N of the external forces.
Teacher's Note: M is perpendicular to the rod and precesses about the axis; its modulus is constant but its vector changes.
Exam Note: Distinguish |M| unchanged from |ΔM|; torque = ω × M.
Question 283. A top of mass m = 0.50 kg, whose axis is tilted by an angle θ = 30° to the vertical, precesses due to gravity. The moment of inertia of the top relative to its symmetry axis is equal to I = 2.0 g·m2, the angular velocity of rotation about that axis is equal to ω = 350 rad/s, the distance from the point of rest to the centre of inertia of the top is l = 10 cm. Find: (a) the angular velocity of the top's precession; (b) the magnitude and direction of the horizontal component of the reaction force acting on the top at the point of rest.
Solution. Here M = Iω is along the symmetry axis. It has two components: Mz = Iω cos θ is constant and the part M⊥ = Iω sin θ precesses, so
|dM/dt| = Iω sin θ ω′ = mgl sin θ, or ω′ = mgl/(Iω) = 0.7 rad/s.
(b) This force is the centripetal force due to precession. It acts inward (towards the axis of precession) and has the magnitude |F| = |Σmiω′2ρi| = mω′2l sin θ = 12 mN. (ρi is the distance of the i-th element from the axis.) This is the force that the table exerts on the top.
Teacher's Note: Gravity torque mgl sinθ equals rate of change of horizontal part of L, which turns at rate ω′.
Exam Note: Slow precession: ω′ = mgl/(Iω), independent of θ.
Question 284. A gyroscope, a uniform disc of radius R = 5.0 cm at the end of a rod of length l = 10 cm (Fig. 1.73), is mounted on the floor of an elevator car going up with a constant acceleration w = 2.0 m/s2. The other end of the rod is hinged at the point O. The gyroscope precesses with an angular velocity n = 0.5 rps. Neglecting the friction and the mass of the rod, find the proper angular velocity of the disc. (Fig. 1.73: the disc of radius R is mounted on a horizontal rod of length l hinged at O on the floor.)
Solution. The moment of inertia of the disc about its symmetry axis is ½mR2. If its angular velocity is ω, the angular momentum is ½mR2ω. The precession frequency being 2πn, |dM/dt| = ½mR2ω × 2πn.
This must equal m(g + w)l, the effective gravitational torque (g being replaced by g + w in the elevator). Thus ω = (g + w)l/(πR2n) = 300 rad/s.
Teacher's Note: In an accelerating lift effective gravity is g + w; torque equals rate of change of angular momentum.
Exam Note: Replace g by g + w; n is in rev/s here.
Question 285. A top of mass m = 1.0 kg and moment of inertia relative to its own axis I = 4.0 g·m2 spins with an angular velocity ω = 310 rad/s. Its point of rest is located on a block which is shifted in a horizontal direction with a constant acceleration w = 1.0 m/s2. The distance between the point of rest and the centre of inertia of the top equals l = 10 cm. Find the magnitude and direction of the angular velocity of precession ω′.
Solution. The effective g is √(g2 + w2), inclined at the angle tan−1(w/g) with the vertical. With reference to the new "vertical" we proceed as in Problem 283. Thus ω′ = ml√(g2 + w2)/(Iω) = 0.8 rad/s. The vector ω′ forms an angle θ = tan−1(w/g) = 6° with the normal vertical.
Teacher's Note: Horizontal acceleration tilts effective gravity by tan⁻¹(w/g); precession axis follows it.
Exam Note: Use g_eff = √(g²+w²); give magnitude and tilt 6°.
Question 286. A uniform sphere of mass m = 5.0 kg and radius R = 6.0 cm rotates with an angular velocity ω = 1250 rad/s about a horizontal axle passing through its centre and fixed on the mounting base by means of bearings. The distance between the bearings equals l = 15 cm. The base is set in rotation about a vertical axis with an angular velocity ω′ = 5.0 rad/s. Find the modulus and direction of the gyroscopic forces.
Solution. The moment of inertia of the sphere is (2/5)mR2, hence its angular momentum is (2/5)mR2ω. Since it precesses at ω′, the required torque is (2/5)mR2ωω′ = F′l. So F′ = (2/5)mR2ωω′/l = 300 N. (The force F′ must be vertical.)
Teacher's Note: Forcing precession needs torque Iωω′, supplied by equal and opposite vertical forces at the two bearings.
Exam Note: Force = torque / bearing separation; direction vertical.
Question 287. A cylindrical disc of a gyroscope of mass m = 15 kg and radius r = 5.0 cm spins with an angular velocity ω = 330 rad/s. The distance between the bearings in which the axle of the disc is mounted is equal to l = 15 cm. The axle is forced to oscillate about a horizontal axis with a period T = 1.0 s and amplitude φm = 20°. Find the maximum value of the gyroscopic forces exerted by the axle on the bearings.
Solution. The moment of inertia is ½mr2 and the angular momentum is ½mr2ω. The axle oscillates about a horizontal axis making an instantaneous angle φ = φm sin(2πt/T). This means there is a variable precession with rate dφ/dt, the maximum value of which is 2πφm/T. When the angle between the axle and the axis is at its maximum, a torque Iω Ω = ½mr2ω(2πφm/T) = πmr2ωφm/T acts on it. The corresponding gyroscopic force is πmr2ωφm/(lT) = 90 N.
Teacher's Note: Oscillation gives variable precession rate; its maximum 2πφm/T gives maximum torque IωΩ.
Exam Note: Convert φm to radians first.
Question 288. A ship moves with velocity v = 36 km per hour along an arc of a circle of radius R = 200 m. Find the moment of the gyroscopic forces exerted on the bearings by the shaft with a flywheel whose moment of inertia relative to the rotation axis equals I = 3.8·103 kg·m2 and whose rotation velocity n = 300 rpm. The rotation axis is oriented along the length of the ship.
Solution. With n the revolutions per minute (converted to per second), the angular momentum of the flywheel is I × 2πn. The rate of precession is v/R. Thus N = 2πInv/R = 5.97 kN·m.
Teacher's Note: Ship's turn rate v/R precesses the flywheel's angular momentum; torque = L × turn rate.
Exam Note: Convert 36 km/h to 10 m/s and 300 rpm to 5 rps.
Question 289. A locomotive is propelled by a turbine whose axle is parallel to the axes of wheels. The turbine's rotation direction coincides with that of wheels. The moment of inertia of the turbine rotor relative to its own axis is equal to I = 240 kg·m2. Find the additional force exerted by the gyroscopic forces on the rails when the locomotive moves along a circle of radius R = 250 m with velocity v = 50 km per hour. The gauge is equal to l = 1.5 m. The angular velocity of the turbine equals n = 1500 rpm.
Solution. As in the previous problem a couple 2πInv/R must come into play. This can be done if a force 2πInv/(Rl) acts on the rails in opposite directions in addition to the centrifugal and other forces. The force on the outer rail is increased and that on the inner rail decreased. The additional force in this case has the magnitude 1.4 kN.
Note: the book prints the unit as kN·m; as a force the unit is kN.
Teacher's Note: Gyroscopic couple 2πInv/R is balanced by a pair of rail forces separated by the gauge l.
Exam Note: Outer rail loaded more; divide the couple by the gauge.
Download IE Irodov Solutions for JEE Math PDF
Complete Math Solutions for IE Irodov Solutions Chapter 5 Dynamics Of A Solid Body Part 2
Access the complete chapter-wise PDF for IE Irodov Solutions Chapter 5 Dynamics Of A Solid Body Part 2. These structured IE Irodov Solutions solutions for JEE Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Mastering Core Concepts with IE Irodov Solutions
Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.
Additional Study Materials for 2026
Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.
FAQs
They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.