Official IE Irodov Textbook Solutions: JEE Physics Chapter 24 Electric Oscillations
Review structured textbook solutions for JEE Physics Chapter 24 Electric Oscillations prepared by IE Irodov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Chapter-wise Solutions for Physics: Chapter 24 Electric Oscillations
Access the complete solution PDF for JEE Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Chapter 24 Electric Oscillations - Questions 123 to 149
Electric Oscillations
Question 123. Draw the approximate voltage vector diagrams in the electric circuits shown in Fig. 4.33 a, b. The external voltage V is assumed to be alternating harmonically with frequency ω.
Solution.
The book gives phasor (vector) diagrams for the two circuits of Fig. 4.33 (the circuit figure itself is not reproduced here), drawn with the current as the reference direction.
Diagram (a): the voltage across the resistance, VR, is drawn along the current. The inductor voltage VL is drawn perpendicular to it. The external voltage V is the vector sum of these (the diagonal of the parallelogram), and it makes an angle φ with the current. The book gives
tan φ = (ωL − 1/ωC)/R, which is negative since ω² < 1/LC.
Diagram (b): VR (along the current) and VL (perpendicular to it) add to give the coil voltage VL,R. The capacitor voltage is drawn along the line perpendicular to the current, opposite to VL. The external voltage V is the vector sum of VL,R and the capacitor voltage, and the angle φ between V and the current is small.
Teacher's Note: Current is the reference; resistor voltage is in phase, inductor leads and capacitor lags by 90°.
Exam Note: Label all vectors and mark φ clearly.
Question 124. A series circuit consisting of a capacitor with capacitance C = 22 μF and a coil with active resistance R = 20 Ω and inductance L = 0.35 H is connected to a source of alternating voltage with amplitude Vm = 180 V and frequency ω = 314 s−1. Find: (a) the current amplitude in the circuit; (b) the phase difference between the current and the external voltage; (c) the amplitudes of voltage across the capacitor and the coil.
Solution.
(a) Im = Vm/√(R² + (ωL − 1/ωC)²) = 4.48 A.
(b) tan φ = (ωL − 1/ωC)/R, φ = −60°. The current lags behind the voltage V by φ (as printed in the book).
(c) VC = Im/ωC = 0.65 kV; VL/R = Im√(R² + ω²L²) = 0.5 kV.
Teacher's Note: Compute X = ωL − 1/ωC first; Z = √(R²+X²) gives Im, and tan φ = X/R.
Exam Note: Show Z, then Im, then each voltage with units.
Question 125. A series circuit consisting of a capacitor with capacitance C, a resistance R, and a coil with inductance L and negligible active resistance is connected to an oscillator whose frequency can be varied without changing the voltage amplitude. Find the frequency at which the voltage amplitude is maximum (a) across the capacitor; (b) across the coil.
Solution.
(a) VC = (1/ωC)·Vm/√(R² + (ωL − 1/ωC)²) = Vm/√((ωRC)² + (ω²LC − 1)²)
= Vm/√((ω²/ω0² − 1)² + 4β²ω²/ω04)
= Vm/√((ω²/ω0² − 1 + 2β²/ω0²)² + 4β²/ω0² − 4β4/ω04)
This is maximum when
ω² = ω0² − 2β² = 1/LC − R²/2L², i.e. ω = √(ω0² − 2β²).
(b) VL = ImωL = VmωL/√(R² + (ωL − 1/ωC)²)
= VmL/√(R²/ω² + (L − 1/ω²C)²) = VmL/√(L² − (1/ω²)(2L/C − R²) + 1/(ω4C²))
= VmL/√((1/ω²C − (L − CR²/2))² + L² − (L − ½CR²)²)
This is maximum when 1/(ω²C) = L − ½CR², or
ω² = 1/(LC − ½C²R²) = 1/(1/ω0² − 2β²/ω04) = ω04/(ω0² − 2β²),
ω = ω0²/√(ω0² − 2β²).
Teacher's Note: Complete the square in the denominator; the maximum occurs when the squared bracket vanishes.
Exam Note: Quote ωC below and ωL above ω0.
Question 126. An alternating voltage with frequency ω = 314 s−1 and amplitude Vm = 180 V is fed to a series circuit consisting of a capacitor and a coil with active resistance R = 40 Ω and inductance L = 0.36 H. At what value of the capacitor's capacitance will the voltage amplitude across the coil be maximum? What is this amplitude equal to? What is the corresponding voltage amplitude across the condenser?
Solution.
VL = Im√(R² + ω²L²) = Vm√(R² + ω²L²)/√(R² + (ωL − 1/ωC)²).
For given ω, L, R, this is maximum when 1/ωC = ωL, or C = 1/ω²L = 28.2 μF.
For that C, VL = Vm√(R² + ω²L²)/R = Vm√(1 + (ωL/R)²) = 0.540 kV.
At this C, VC = (1/ωC)·Vm/R = VmωL/R = 0.509 kV.
Teacher's Note: Coil voltage is largest at resonance of the series circuit, where the capacitor reactance equals ωL.
Exam Note: State C, VL and VC with units.
Question 127. A capacitor with capacitance C whose interelectrode space is filled up with poorly conducting medium with active resistance R is connected to a source of alternating voltage V = Vm cos ωt. Find the time dependence of the steady-state current flowing in lead wires. The resistance of the wires is to be neglected.
Solution.
The capacitor with a poorly conducting medium is equivalent to an ideal capacitor C with the resistance R connected in parallel (current I′ through R, current I − I′ into the capacitor).
Use the complex voltage V = Vmeiωt. The voltage across the capacitor is (I − I′)/(iωC), and that across the resistance is RI′; both equal V. Thus
I′ = (Vm/R)eiωt, I − I′ = iωCVmeiωt.
Hence I = (Vm/R)(1 + iωRC)eiωt.
The actual current is the real part:
I = (Vm/R)√(1 + (ωRC)²) cos(ωt + φ), where tan φ = ωRC.
Note: a condenser with poorly conducting material (dielectric of high resistance) between the plates is equivalent to an ideal condenser with a high resistance joined in parallel between its plates.
Teacher's Note: Treat the leaky capacitor as an ideal C in parallel with R; add the two currents as complex numbers.
Exam Note: Give amplitude and phase φ = tan⁻¹(ωRC).
Question 128. An oscillating circuit consists of a capacitor of capacitance C and a solenoid with inductance L1. The solenoid is inductively connected with a short-circuited coil having an inductance L2 and a negligible active resistance. Their mutual inductance coefficient is equal to L12. Find the natural frequency of the given oscillating circuit.
Solution.
Equations for the two circuits:
L1 dI1/dt + (∫I1dt)/C = −L12 dI2/dt
L2 dI2/dt = −L12 dI1/dt
From the second equation, L2I2 = −L12I1.
Then (L1 − L12²/L2) d²I1/dt² + I1/C = 0.
Thus the current oscillates with frequency
ω = 1/√(C(L1 − L12²/L2)).
Teacher's Note: Short-circuited coil with zero resistance conserves flux, so it lowers the effective inductance of L1.
Exam Note: Write both loop equations before eliminating I2.
Question 129. Find the quality factor of an oscillating circuit connected in series to a source of alternating emf if at resonance the voltage across the capacitor is n times that of the source.
Solution.
Given V = Vm cos ωt, I = Im cos(ωt − φ) for a series circuit with coil (L, R), capacitor C and source V, where
Im = Vm/√(R² + (ωL − 1/ωC)²).
Then VC = (∫I dt)/C = Im sin(ωt − φ)/ωC = Vm/√((1 − ω²LC)² + (ωRC)²) · sin(ωt − φ).
At resonance (ω = 1/√(LC)) the voltage amplitude across the capacitor is
Vm/(RC·(1/√(LC))) = √(L/(CR²)) · Vm = nVm.
So L/(CR²) = n². Now
Q = √(L/(CR²) − 1/4) = √(n² − 1/4).
Teacher's Note: Resonant capacitor voltage is Vm√(L/C)/R; the quality factor then follows from Q² = L/CR² − 1/4.
Exam Note: Give Q = √(n² − 1/4), not simply n.
Question 130. An oscillating circuit consisting of a coil and a capacitor connected in series is fed an alternating emf, with coil inductance being chosen to provide the maximum current in the circuit. Find the quality factor of the system, provided an n-fold increase of inductance results in an η-fold decrease of the current in the circuit.
Solution.
The current amplitude Im = Vm/√(R² + (ωL − 1/ωC)²) is maximum when L = 1/(ω²C), and then Im0 = Vm/R.
Now with the inductance increased n-fold, ωL − 1/ωC = (n − 1)/ωC, so
Im0/η = Vm/√(R² + (n − 1)²/(ω²C²)).
So η = √(1 + (n − 1)²/(ωRC)²), giving ωRC = (n − 1)/√(η² − 1).
Now Q = √(L/(CR²) − 1/4) = √((1/ωRC)² − 1/4), since L/(CR²) = 1/(ωRC)²:
Q = √((η² − 1)/(n − 1)² − 1/4).
Teacher's Note: At the chosen L the circuit is at resonance, so L = 1/ω²C converts the data into ωRC.
Exam Note: Show ωRC first, then substitute into Q.
Question 131. A series circuit consisting of a capacitor and a coil with active resistance is connected to a source of harmonic voltage whose frequency can be varied, keeping the voltage amplitude constant. At frequencies ω1 and ω2 the current amplitudes are n times less than the resonance amplitude. Find: (a) the resonance frequency; (b) the quality factor of the circuit.
Solution.
At resonance ω0L = 1/(ω0C), i.e. ω0 = 1/√(LC), and (Im)res = Vm/R.
Now Vm/(nR) = Vm/√(R² + (ω1L − 1/ω1C)²) = Vm/√(R² + (ω2L − 1/ω2C)²).
Then ω1L − 1/(ω1C) = −√(n² − 1) R and ω2L − 1/(ω2C) = +√(n² − 1) R (assuming ω2 > ω1),
or ω1 − ω0²/ω1 = −ω2 + ω0²/ω2 = −√(n² − 1) R/L.
Hence ω1 + ω2 = (ω0²/(ω1ω2))(ω1 + ω2), so (a) ω0 = √(ω1ω2).
Also ω2 − ω1 = √(n² − 1) R/L, so β = R/2L = (ω2 − ω1)/(2√(n² − 1)).
(b) Q = √(ω0²/(4β²) − 1/4) = √((n² − 1)ω1ω2/(ω2 − ω1)² − 1/4).
Teacher's Note: The two half-power-type frequencies satisfy opposite-sign reactance conditions; adding them gives the geometric mean.
Exam Note: State ω0 = √(ω1ω2) before finding Q.
Question 132. Demonstrate that at low damping the quality factor Q of a circuit maintaining forced oscillations is approximately equal to ω0/Δω, where ω0 is the natural oscillation frequency, Δω is the width of the resonance curve I(ω) at the "height" which is √2 times less than the resonance current amplitude.
Solution.
For low damping, Q = ω/2β ≈ ω0/2β.
Now Im/√2 = R Im/√(R² + (ωL − 1/ωC)²), where Im is the current amplitude at resonance.
Or ω − ω0²/ω = ±R/L = ±2β.
Thus ω ≈ ω0 ± β.
So Δω = 2β and Q = ω0/Δω.
Teacher's Note: Set current to 1/√2 of resonance: reactance equals ±R, giving frequencies ω0 ± β for small β.
Exam Note: State the low-damping approximation ω ≈ ω0 ± β clearly.
Question 133. A circuit consisting of a capacitor and a coil connected in series is fed two alternating voltages of equal amplitudes but different frequencies. The frequency of one voltage is equal to the natural oscillation frequency (ω0) of the circuit, the frequency of the other voltage is η times higher. Find the ratio of the current amplitudes (I0/I) generated by the two voltages if the quality factor of the system is equal to Q. Calculate this ratio for Q = 10 and 100, if η = 1.10.
Solution.
At resonance ω = ω0, Im(ω0) = Vm/R.
Then Im(ηω0) = Vm/√(R² + (ηω0L − 1/(ηω0C))²) = Vm/√(R² + (η − 1/η)² L/C) = Vm/(R√(1 + (Q² + 1/4)(η − 1/η)²)),
using L/(CR²) = Q² + 1/4. Hence
I0/I = √(1 + (Q² + 1/4)(η − 1/η)²).
For η = 1.10: I0/I ≈ 2.2 for Q = 10, and ≈ 19 for Q = 100. (These two numerical values are not shown in the scanned source and were computed here: 2.16 and 19.1.)
Teacher's Note: Reactance at ηω0 equals (η − 1/η)√(L/C); divide by R to bring in Q.
Exam Note: Give the formula, then both numbers.
Question 134. It takes t0 hours for a direct current I0 to charge a storage battery. How long will it take to charge such a battery from the mains using a half-wave rectifier, if the effective current value is also equal to I0?
Solution.
The a.c. current must be I = I0√2 sin ωt.
Then the d.c. component of the rectified current is
⟨I′⟩ = (1/T)∫0T/2 I0√2 sin ωt dt = I0√2 · (1/2π) ∫0π sin θ dθ = I0√2/π.
Since the charge deposited must be the same, I0t0 = (I0√2/π)t, so t = πt0/√2 ≈ 2.2 t0.
Teacher's Note: Charge depends on the mean (d.c.) component; half-wave rectification gives Im/π.
Exam Note: Effective value of the a.c. before rectifying is I0; state it.
Question 135. Find the effective value of current if its mean value is I0 and its time dependence is (a) shown in Fig. 4.34 (a saw-tooth current rising linearly from zero to a maximum in each period and then dropping back to zero); (b) I ∝ |sin ωt|.
Solution.
(a) I(t) = I1t/T for 0 ≤ t < T, with I(t ± T) = I(t).
Mean current ⟨I⟩ = (1/T)∫0T I1(t/T) dt = I1T²/(2T²) = I1/2. Then I1 = 2I0 since ⟨I⟩ = I0.
Mean square current ⟨I²⟩ = 4I0² (1/T)∫0T (t²/T²) dt = 4I0²/3.
So effective current = 2I0/√3.
(b) Here I = I1|sin ωt| and I0 = (1/T)∫0T I1|sin ωt| dt = (I1/2π)∫02π |sin θ| dθ = (I1/π)∫0π sin θ dθ = 2I1/π.
So I1 = πI0/2. Then the mean square current is ⟨I²⟩ = (π²I0²/4)(1/T)∫0T sin² ωt dt = (π²I0²/4)(1/2π)∫02π sin² θ dθ = π²I0²/8.
So effective current = πI0/√8 = πI0/(2√2).
Teacher's Note: Mean value fixes the peak I1; then rms is √(mean of I²) over one period.
Exam Note: Find I1 from the mean first, then rms.
Question 136. A solenoid with inductance L = 7 mH and active resistance R = 44 Ω is first connected to a source of direct voltage V0 and then to a source of sinusoidal voltage with effective value V = V0. At what frequency of the oscillator will the power consumed by the solenoid be η = 5.0 times less than in the former case?
Solution.
Pd.c. = V0²/R.
Pa.c. = (V0²/√(R² + ω²L²))·(R/√(R² + ω²L²)) = (V0²/R)/(1 + (ωL/R)²) = Pd.c./η.
Thus ωL/R = √(η − 1), or ω = (R/L)√(η − 1).
ν = (R/2πL)√(η − 1) ≈ 2 kHz on putting the values.
Teacher's Note: Average a.c. power is V²R/Z²; equate to Pd.c./η to get ωL/R.
Exam Note: Use effective (rms) values; give ν not ω.
Question 137. A coil with inductive resistance XL = 30 Ω and impedance Z = 50 Ω is connected to the mains with effective voltage value V = 100 V. Find the phase difference between the current and the voltage, as well as the heat power generated in the coil.
Solution.
Z = √(R² + XL²), or R = √(Z² − XL²) = 40 Ω.
tan φ = XL/√(Z² − XL²), so cos φ = √(Z² − XL²)/Z = √(1 − (XL/Z)²).
The current lags by φ behind the voltage: φ = cos⁻¹√(1 − (XL/Z)²) = 37°.
Also P = VI cos φ = (V²/Z²)√(Z² − XL²) = 0.160 kW.
Teacher's Note: Resistance follows from Z and XL; heat power is I²R = V²R/Z², not V²/Z.
Exam Note: Give φ with 'current lags' and power in watts.
Question 138. A coil with inductance L = 0.70 H and active resistance r = 20 Ω is connected in series with an inductance-free resistance R. An alternating voltage with effective value V = 220 V and frequency ω = 314 s−1 is applied across the terminals of this circuit. At what value of the resistance R will the maximum heat power be generated in the circuit? What is it equal to?
Solution.
P = V²(R + r)/((R + r)² + ω²L²).
This is maximum when R + r = ωL, for
P = V²/(R + r + (ωL)²/(R + r)) = V²/([√(R + r) − ωL/√(R + r)]² + 2ωL).
Thus R = ωL − r for maximum power, and Pmax = V²/(2ωL).
Substituting the values, R ≈ 200 Ω and Pmax = 0.110 kW.
Corrected: the book prints Pmax = 0.114 kW; V²/(2ωL) = 220²/(2 × 314 × 0.70) = 110 W.
Teacher's Note: Source power is largest when total resistance R + r equals the coil reactance ωL.
Exam Note: Quote R = ωL − r, then Pmax = V²/2ωL.
Question 139. A circuit consisting of a capacitor and a coil in series is connected to the mains. Varying the capacitance of the capacitor, the heat power generated in the coil was increased n = 1.7 times. How much (in per cent) was the value of cos φ changed in the process?
Solution.
P = V²R/(R² + (XL − XC)²).
Varying the capacitor does not change R, so if P increases n times, Z = √(R² + (XL − XC)²) must decrease √n times.
Thus cos φ = R/Z increases √n times, so the % increase in cos φ = (√n − 1) × 100% = 30.4% (about 30%).
Teacher's Note: Only Z changes with C, so power ∝ 1/Z² and cos φ = R/Z ∝ 1/Z.
Exam Note: Answer is the percentage increase, (√n − 1) × 100.
Question 140. A source of sinusoidal emf with constant voltage is connected in series with an oscillating circuit with quality factor Q = 100. At a certain frequency of the external voltage the heat power generated in the circuit reaches the maximum value. How much (in per cent) should this frequency be shifted to decrease the power generated n = 2.0 times?
Solution.
P = V²R/(R² + (XL − XC)²). At resonance XL = XC ⇒ ω0 = 1/√(LC).
Power decreases n times when (XL − XC)² = (ωL − 1/ωC)² = (n − 1)R²,
or ω − ω0²/ω = ±√(n − 1) R/L = ±√(n − 1) 2β.
Thus ω² ∓ 2√(n − 1) βω − ω0² = 0, so (ω ∓ √(n − 1) β)² = ω0² + (n − 1)β²,
or ω/ω0 = √(1 + (n − 1)β²/ω0²) ± √(n − 1) β/ω0.
(Taking only the positive sign in the first term to ensure a positive value for ω/ω0.)
Now Q = ω/2β = ½√((ω0/β)² − 1), so ω0/β = √(1 + 4Q²). Thus
ω/ω0 = √(1 + (n − 1)/(1 + 4Q²)) ± √(n − 1)/√(1 + 4Q²).
For large Q: |ω − ω0|/ω0 = √(n − 1)/(2Q) = (√(n − 1)/2Q) × 100% = 0.5%.
Teacher's Note: Power halves when reactance equals ±R; for large Q the shift is √(n − 1)/2Q.
Exam Note: Give the shift as a percentage of ω0.
Question 141. A series circuit consisting of an inductance-free resistance R = 0.16 kΩ and a coil with active resistance is connected to the mains with effective voltage V = 220 V. Find the heat power generated in the coil if the effective voltage values across the resistance R and the coil are equal to V1 = 80 V and V2 = 180 V respectively.
Solution.
Let R1 be the active resistance and XL the reactance of the coil. We have
V1 = VR/√((R + R1)² + XL²), V2 = V√(R1² + XL²)/√((R + R1)² + XL²),
so (R + R1)² + XL² = (VR/V1)², R1² + XL² = (V2R/V1)².
Hence R² + 2RR1 = (R²/V1²)(V² − V2²), or R1 = (R/2V1²)(V² − V2² − V1²).
Heat generated in the coil = V1²R1/R² = (V1²/R²) × (R²/2V1²)(V² − V1² − V2²) = (V² − V1² − V2²)/(2R) = 30 W.
Teacher's Note: Same current flows in both; subtract squared voltages to isolate the coil's resistive part.
Exam Note: Coil heat power uses its resistance R1, not its impedance.
Question 142. A coil and an inductance-free resistance R = 25 Ω are connected in parallel to the ac mains. Find the heat power generated in the coil provided a current I = 0.90 A is drawn from the mains. The coil and the resistance R carry currents I1 = 0.50 A and I2 = 0.60 A respectively.
Solution.
Here I2 = V/R (V effective voltage), I1 = V/√(R1² + XL²) (R1, XL for the coil), and
I = V√((R + R1)² + XL²)/(R√(R1² + XL²)) = V/Reff, where Reff is the impedance of the coil and the resistance in parallel.
Now (I² − I2²)/I2² = (R² + 2RR1)/(R1² + XL²) = (I1/I2)² + 2RR1/(R1² + XL²),
so (I² − I2² − I1²)/I2² = 2RR1/(R1² + XL²).
Mean power consumed in the coil = I1²R1 = V²R1/(R1² + XL²) = I2²R(I² − I1² − I2²)/(2I2²) = ½R(I² − I1² − I2²) = 2.5 W.
Teacher's Note: Total current is the vector sum of branch currents; the cosine rule isolates the coil's in-phase part.
Exam Note: Final formula: P = ½R(I² − I1² − I2²).
Question 143. An alternating current of frequency ω = 314 s−1 is fed to a circuit consisting of a capacitor of capacitance C = 73 μF and an active resistance R = 100 Ω connected in parallel. Find the impedance of the circuit.
Solution.
1/Z = 1/R + 1/(1/iωC) = 1/R + iωC = (1 + iωRC)/R.
|Z| = R/√(1 + (ωRC)²) = 40 Ω.
Corrected: the source prints the capacitance as "73 ηF" (a misprint); with C = 73 μF the book's answer 40 Ω is obtained (ωRC = 2.29).
Teacher's Note: Parallel R and C: add admittances 1/R and iωC, then take the modulus.
Exam Note: Write |Z| = R/√(1 + (ωRC)²) with units.
Question 144. Draw the approximate vector diagrams of currents in the circuits shown in Fig. 4.35. The voltage applied across the points A and B is assumed to be sinusoidal; the parameters of each circuit are so chosen that the total current I0 lags in phase behind the external voltage by an angle φ. Fig. 4.35: (a) resistance R in parallel with a coil (L, r); (b) capacitor C in parallel with a coil (L, R); (c) resistance R in parallel with a branch of capacitor C and coil L in series.
Solution.
(a) For the resistance, the voltage and the current are in phase. For the coil the voltage is ahead of the current by less than 90°. The current is obtained by addition because the elements are in parallel.
(b) IC is ahead of the voltage by 90°; the coil current IL,R lags it by less than 90°, and the total current I0 is their sum.
(c) The coil has no resistance, so IL is 90° behind the voltage, while IC is 90° ahead of it; IR is in phase. I0 = IR + IC + IL (with IL larger than IC so that I0 lags).
(Diagrams redrawn schematically; vector lengths are illustrative.)
Teacher's Note: In parallel branches add currents as vectors: resistor in phase, inductor lags, capacitor leads voltage.
Exam Note: Take voltage as reference axis and label every current.
Question 145. A capacitor with capacitance C = 1.0 μF and a coil with active resistance R = 0.10 Ω and inductance L = 1.0 mH are connected in parallel to a source of sinusoidal voltage V = 31 V. Find: (a) the frequency ω at which the resonance sets in; (b) the effective value of the fed current in resonance, as well as the corresponding currents flowing through the coil and through the capacitor.
Solution.
When the coil and the condenser are in parallel, the equations are
L dI1/dt + RI1 = (∫I2dt)/C = Vm cos ωt, I = I1 + I2.
Using complex voltages: I1 = Vmeiωt/(R + iωL), I2 = iωCVmeiωt, and
I = (1/(R + iωL) + iωC)Vmeiωt = [(R − iωL + iωC(R² + ω²L²))/(R² + ω²L²)]Vmeiωt.
Thus, taking real parts, I = (Vm/|Z(ω)|) cos(ωt − φ), where
1/|Z(ω)| = [R² + {ωC(R² + ω²L²) − ωL}²]1/2/(R² + ω²L²), and tan φ = (ωL − ωC(R² + ω²L²))/R.
(a) To get the frequency of resonance we must define what we mean by resonance. One definition requires the extremum (maximum or minimum) of the current amplitude. The other requires rapid change of phase, with φ passing through zero at resonance. For the series circuit Im = Vm/{R² + (ωL − 1/ωC)²}1/2 and tan φ = (ωL − 1/ωC)/R; both definitions give ω² = 1/LC. In the present case the two definitions do not agree (except when R = 0). The definition adopted in the answer given in the book is the vanishing of phase. This requires C(R² + ω²L²) = L, or
ω² = 1/LC − R²/L² = ωres², ωres = 31.6 × 10³ rad/s.
Note that for small R, φ rapidly changes from −π/2 to +π/2 as ω passes through ωres.
(b) At resonance Im = VmR/(L/C) = VmCR/L. So the effective value of the total current is I = VCR/L = 3.1 mA.
Similarly IL = V/√(L/C) = V√(C/L) = 0.98 A, and IC = ωCV = V√(C/L − R²C²/L²) = 0.98 A.
Note: the vanishing of phase (its passing through zero) is considered a more basic definition of resonance.
Teacher's Note: Parallel resonance here means zero phase: C(R² + ω²L²) = L; then the line current is tiny.
Exam Note: State which resonance definition you use.
Question 146. A capacitor with capacitance C and a coil with active resistance R and inductance L are connected in parallel to a source of sinusoidal voltage of frequency ω. Find the phase difference between the current fed to the circuit and the source voltage.
Solution.
We use the method of complex voltage V = V0eiωt. Then IC = V0eiωt/(1/iωC) = iωCV0eiωt and IL,R = V0eiωt/(R + iωL).
I = IC + IL,R = V0 [(R − iωL + iωC(R² + ω²L²))/(R² + ω²L²)] eiωt.
Then taking the real part,
I = V0√(R² + {ωC(R² + ω²L²) − ωL}²)/(R² + ω²L²) · cos(ωt − φ),
where tan φ = (ωL − ωC(R² + ω²L²))/R.
Teacher's Note: Add the capacitor and coil branch currents as complex numbers; the phase comes from their ratio of parts.
Exam Note: Give tan φ with its sign convention (cos(ωt − φ)).
Question 147. A circuit consists of a capacitor with capacitance C and a coil with active resistance R and inductance L connected in parallel. Find the impedance of the circuit at frequency ω of alternating voltage.
Solution.
From the previous problem
Z = (R² + ω²L²)/√(R² + {ωC(R² + ω²L²) − ωL}²)
= (R² + ω²L²)/√((R² + ω²L²)(1 − 2ω²LC) + ω²C²(R² + ω²L²)²)
= √(R² + ω²L²)/√((1 − 2ω²LC) + ω²C²(R² + ω²L²))
= √(R² + ω²L²)/√((1 − ω²LC)² + (ωRC)²).
Teacher's Note: Expand the square under the root and regroup it as (1 − ω²LC)² + (ωRC)².
Exam Note: Final form must show both terms under the root.
Question 148. A ring of thin wire with active resistance R and inductance L rotates with constant angular velocity ω in the external uniform magnetic field perpendicular to the rotation axis. In the process, the flux of magnetic induction of the external field across the ring varies with time as Φ = Φ0 cos ωt. Demonstrate that (a) the inductive current in the ring varies with time as I = Im sin(ωt − φ), where Im = ωΦ0/√(R² + ω²L²) with tan φ = ωL/R; (b) the mean mechanical power developed by external forces to maintain rotation is defined by the formula P̄ = ½ω²Φ0²R/(R² + ω²L²).
Solution.
(a) We have ε = −dΦ/dt = ωΦ0 sin ωt = L dI/dt + RI.
Put I = Im sin(ωt − φ). Then
ωΦ0 sin ωt = ωΦ0{sin(ωt − φ)cos φ + cos(ωt − φ)sin φ} = LImω cos(ωt − φ) + RIm sin(ωt − φ).
So RIm = ωΦ0 cos φ and LIm = Φ0 sin φ, or
Im = ωΦ0/√(R² + ω²L²) and tan φ = ωL/R.
(b) Mean mechanical power required to maintain rotation = energy loss per unit time
= (1/T)∫0T RI² dt = ½RIm² = ½ω²Φ0²R/(R² + ω²L²).
Teacher's Note: Match sin(ωt − φ) and cos(ωt − φ) coefficients; mean power is ½RIm², since no energy is stored on average.
Exam Note: Show both coefficient equations before solving.
Question 149. A wooden core (Fig. 4.36) supports two coils: coil 1 with inductance L1 and short-circuited coil 2 with active resistance R and inductance L2. The mutual inductance of the coils depends on the distance x between them according to the law L12(x). Find the mean (averaged over time) value of the interaction force between the coils when coil 1 carries an alternating current I1 = I0 cos ωt.
Solution.
We consider the force F12 that a circuit 1 exerts on another closed circuit 2: F12 = ∮ I2 dl2 × B12, where B12 is the magnetic field at the site of the current element dl2 due to the current I1 flowing in 1:
B12 = (μ0/4π)∮ I1 dl1 × r12/r12³, where r12 = r2 − r1 is the vector from dl1 to dl2.
Now F12 = (μ0/4π)∬ I1I2 dl2 × (dl1 × r12)/r12³ = (μ0/4π)∬ I1I2 [dl1(dl2·r12) − (dl1·dl2)r12]/r12³.
In the first term, carry out the integration over dl2 first. Then ∮ (dl2·r12)/r12³ = −∮ dl2·∇2(1/r12) = 0, because this equals −∫ dS2·curl(∇(1/r12)) = 0. Thus
F12 = −(μ0/4π)∬ I1I2 (dl1·dl2) r12/r12³.
The integral depends on the vector a that defines the separation of the (suitably chosen) centres C1 and C2 of the two coils. Write r12 = r2 − r1 = ρ2 − ρ1 + a, where ρ1 (ρ2) is the position of dl1 (dl2) from C1 (C2) and a = C1C2. Then r12/r12³ = −∇a(1/r12) and
F12 = ∇a[I1I2 (μ0/4π)∬ dl1·dl2/r12].
The bracket defines the mutual inductance L12. Thus, noting the definition of x, ⟨Fx⟩ = (∂L12/∂x)⟨I1I2⟩, where ⟨ ⟩ denotes time average.
Now I1 = I0 cos ωt = real part of I0eiωt. The current in coil 2 satisfies RI2 + L2 dI2/dt = −L12 dI1/dt, or (complex) I2 = −iωL12I0eiωt/(R + iωL2). Taking the real part,
I2 = −(ωL12I0/(R² + ω²L2²))(ωL2 cos ωt − R sin ωt) = −(ωL12/√(R² + ω²L2²)) I0 cos(ωt + φ), where tan φ = R/(ωL2).
Taking the time average, ⟨I1I2⟩ = −½ I0·(ωL12I0/√(R² + ω²L2²)) cos φ, so
⟨Fx⟩ = −ω²L2L12I0²/(2(R² + ω²L2²)) · ∂L12/∂x.
The repulsive nature of the force is also consistent with Lenz's law, assuming, of course, that L12 decreases with x (so ∂L12/∂x < 0 and ⟨Fx⟩ > 0).
Corrected: the printed final result omits the minus sign (the printed step has the plus sign, which would give attraction for decreasing L12); redoing the average gives the negative sign shown above.
Teacher's Note: Induced current in the shorted coil lags and opposes I1, so coils repel; force = ⟨I1I2⟩∂L12/∂x.
Exam Note: Mention repulsion and that L12 falls with x.
Download IE Irodov Solutions for JEE Math PDF
Chapter-wise IE Irodov Solutions: IE Irodov Solutions Chapter 24 Electric Oscillations Part 2
Review detailed solutions for JEE Mathematics. The IE Irodov Solutions Chapter 24 Electric Oscillations Part 2 PDF provides comprehensive answers mapped to standard IE Irodov Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Concept-Driven Math Answers
Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.
Explore More Study Resources for JEE Math
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.