Step-by-Step IE Irodov Solutions for JEE Physics Chapter 20 Constant Magnetic Field Magnetics
Review structured textbook solutions for JEE Physics Chapter 20 Constant Magnetic Field Magnetics prepared by IE Irodov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Download Chapter 20 Constant Magnetic Field Magnetics Textbook Solutions PDF
Access the complete solution PDF for JEE Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Constant Magnetic Field - Questions 219 to 251
Questions 219-251
Question 219. A current I = 1.00 A circulates in a round thin-wire loop of radius R = 100 mm. Find the magnetic induction (a) at the centre of the loop; (b) at the point lying on the axis of the loop at a distance x = 100 mm from its centre.
Solution. (a) From the Biot-Savart law, dB = (μ0/4π) I (dl × r)/r3. Since dl ⊥ r, dB = (μ0/4π) I (R dθ) R/R3. By symmetry all contributions point along the axis, so
B = ∫dB = ∫02π (μ0/4π)(I/R) dθ = μ0I/(2R) = 6.3 μT.
(b) From the Biot-Savart law, B = (μ0/4π) I ∮ dl × r/r3, where r = R + x. So B = (μ0/4π)(I/r3)[∮dl × R + ∮dl × x]. Since x is a constant vector, ∮dl × x = (∮dl) × x = 0. Also ∮dl × R = ∮R dl n = 2πR2 n, where n is the unit vector perpendicular to the plane of the loop, along the axis. Thus
B = (μ0/4π) · 2πR2I/(x2 + R2)3/2 n.
For x = R: B = μ0I/(4√2 R) ≈ 2.2 μT. (Answer: 6.3 μT and 2.2 μT.)
Teacher's Note: On-axis terms cancel except the axial component; at x = R the field is 1/23/2 of the centre value.
Exam Note: State the axial formula, then substitute x = R.
Question 220. A current I flows along a thin wire shaped as a regular polygon with n sides which can be inscribed into a circle of radius R. Find the magnetic induction at the centre of the polygon. Analyse the obtained expression for n → ∞.
Solution. Let AB be one side with centre O of the polygon, and OC the perpendicular from O to AB. Since ∠AOB = 2π/n, the perpendicular distance of any side from the centre is R cos(π/n).
The field at O due to side AB is perpendicular to the plane of the figure, with magnitude
B = ∫(μ0/4π) I (dx/r2) cos θ = ∫−π/nπ/n (μ0I/4π)(R cos(π/n) sec2θ dθ)/(R2cos2(π/n) sec2θ) cos θ = (μ0I/4π)(1/(R cos(π/n))) · 2 sin(π/n).
All n sides give fields of equal magnitude and the same direction at O. So
B0 = (μ0/4π)(nI/(R cos(π/n))) · 2 sin(π/n) = (μ0/2π)(nI/R) tan(π/n).
For n → ∞: B0 = (μ0I/2R) limn→∞ [tan(π/n)/(π/n)] = μ0I/(2R), the field at the centre of a circular loop.
Teacher's Note: Each side contributes equally; the limit tan x/x → 1 recovers the circular-loop result.
Exam Note: Show the limit step to earn the analysis mark.
Question 221. Find the magnetic induction at the centre of a rectangular wire frame whose diagonal is equal to d = 16 cm and the angle between the diagonals is equal to φ = 30°; the current flowing in the frame equals I = 5.0 A.
Solution. The magnetic induction due to a straight current-carrying wire at a point at perpendicular distance r from it is B = (μ0/4π)(I/r)(sin θ1 + sin θ2), where θ1, θ2 are the angles that the lines joining the ends of the wire to the point make with the perpendicular to the wire.
For the two sides of the frame opposite the angle φ (sides 1 and 3): B1 = B3 = (μ0/4π) · I/((d/2) sin(φ/2)) · [cos(φ/2) + cos(φ/2)].
For the other two sides (2 and 4): B2 = B4 = (μ0/4π) · I/((d/2) cos(φ/2)) · [sin(φ/2) + sin(φ/2)].
All four fields point the same way, so
B0 = B1 + B2 + B3 + B4 = (μ0/4π)(4I/(d/2)) [cos(φ/2)/sin(φ/2) + sin(φ/2)/cos(φ/2)] = 4μ0I/(π d sin φ) = 0.10 mT.
Teacher's Note: Use the finite-wire formula for each side; cot + tan simplifies to 2/sin φ.
Exam Note: Check numbers: 4μ0I/(πd sin φ) = 0.10 mT.
Question 222. A current I = 5.0 A flows along a thin wire shaped as shown in Fig. 3.59 (a circular arc of radius R = 120 mm subtending 2π − 2φ at the centre O, closed by a straight chord that subtends 2φ at O). The angle 2φ = 90°. Find the magnetic induction of the field at the point O.
Solution. The magnetic induction due to the arc segment at O is Barc = (μ0/4π)(I/R)(2π − 2φ).
The straight segment (the chord, at perpendicular distance R cos φ from O, with both ends at angle φ) gives Bline = (μ0/4π)(I/(R cos φ))[2 sin φ].
Both fields point the same way, so the total at O is
B0 = Barc + Bline = (μ0/2π)(I/R)[π − φ + tan φ] = 28 μT.
Teacher's Note: Arc field is proportional to its angle; chord uses the finite straight-wire formula, and both add.
Exam Note: Convert φ to radians (π/4) before substituting.
Question 223. Find the magnetic induction of the field at the point O of a loop with current I, whose shape is illustrated (a) in Fig. 3.60a, where the radii a and b, as well as the angle φ are known; (b) in Fig. 3.60b, where the radius a and the side b are known. (In (a) the loop consists of an arc of radius a subtending 2π − φ at O, two radial straight pieces, and an arc of radius b subtending φ at O. In (b) it consists of an arc of radius a subtending 3π/2 at O, two straight pieces along radii, and three sides of a square of side b; the straight piece 5 passes through O.)
Solution. (a) From the Biot-Savart law, dB = (μ0/4π) I (dl × r)/r3. The field due to segment 1 (arc of radius a) at O is B1 = (μ0/4π)(I/a)(2π − φ). The radial segments give B2 = B4 = 0, since dl ∥ r. The arc of radius b gives B3 = (μ0/4π)(I/b)φ. Hence
B0 = B1 + B2 + B3 + B4 = (μ0/4π) I [(2π − φ)/a + φ/b].
(b) Here B1 = (μ0/4π)(I/a)(3π/2), B2 = 0, B3 = (μ0/4π)(I/b) sin 45°, B4 = (μ0/4π)(I/b) sin 45°, and B5 = 0. So
B0 = (μ0/4π) I [3π/(2a) + √2/b].
Teacher's Note: Radial wires through O give zero; arcs give (μ0I/4πr)×angle; far square sides use sin 45°.
Exam Note: Mark which segments vanish; add the rest.
Question 224. A current I flows along a lengthy thin-walled tube of radius R with a longitudinal slit of width h. Find the induction of the magnetic field inside the tube under the condition h ≪ R.
Solution. The thin-walled tube with a longitudinal slit can be considered equivalent to a full tube plus a strip carrying the same current density in the opposite direction. Inside the tube the former does not contribute, so the total magnetic field is simply that due to the strip:
B = (μ0/2π) · ((I/2πR)h)/r = μ0Ih/(4π2Rr),
where r is the distance of the field point from the strip. (On the axis r = R, so B = μ0Ih/(4π2R2).)
Teacher's Note: Superposition: full tube (zero inside, Ampere's law) plus a narrow reverse-current strip acting as a thin wire.
Exam Note: Name the superposition idea explicitly.
Question 225. A current I flows in a long straight wire with cross-section having the form of a thin half-ring of radius R (Fig. 3.61). Find the induction of the magnetic field at the point O (the centre of the half-ring).
Solution. First find the direction of B at O. Divide the conductor into elementary long strips carrying current dI. The sum of the fields of any two symmetric strips is along the symmetry axis of the half-ring (perpendicular to the line joining O to the middle of the ring), so the vector B is directed along that axis. So
B = ∫dB sin φ = ∫(μ0/2πR) dI sin φ = ∫0π (μ0/2π2R) I sin φ dφ, (as dI = (I/π)dφ)
Hence B = μ0I/(π2R).
Teacher's Note: Each strip acts as a long wire; only components along the symmetry axis survive.
Exam Note: Justify the symmetry before integrating.
Question 226. Find the magnetic induction of the field at the point O if a current-carrying wire has the shape shown in Fig. 3.62 a, b, c. The radius of the curved part of the wire is R, the linear parts are assumed to be very long. ((a) two collinear straight wires joined by a semicircle of radius R with O at its centre; (b) a straight wire ending tangentially in a 3π/2 arc of radius R, with the return wire parallel; (c) two parallel straight wires joined by a semicircle of radius R with O at its centre.)
Solution. (a) From symmetry, the straight parts lie along lines through O, so B1 = B3 = 0:
B0 = B1 + B2 + B3 = 0 + (μ0/4π)(I/R)π + 0 = μ0I/(4R).
(b) B0 = B1 + B2 + B3 = (μ0/4π)(I/R) + (μ0/4π)(I/R)(3π/2) + 0 = (μ0/4π)(I/R)[1 + 3π/2].
(c) B0 = B1 + B2 + B3 = (μ0/4π)(I/R) + (μ0/4π)(I/R)π + (μ0/4π)(I/R) = (μ0/4π)(I/R)(2 + π).
Teacher's Note: Semi-infinite wire ending at the foot of the perpendicular gives μ0I/4πR; arc gives angle × μ0I/4πR.
Exam Note: Check each part's direction before adding.
Question 227. A very long wire carrying a current I = 5.0 A is bent at right angles. Find the magnetic induction at a point lying on a perpendicular to the wire, drawn through the point of bending, at a distance l = 35 cm from it.
Solution. The point lies on the perpendicular to the plane of the bend drawn through the corner, so it is at distance l from each arm, with the foot of the perpendicular at the corner. Each arm is a semi-infinite wire, so each gives μ0I/(4πl) (using the result of Problem 221), and the two fields B1, B2 are perpendicular. Hence
|B0| = |B1 + B2| = (μ0I/(4πl))·√2 = 2.0 μT.
Teacher's Note: Two perpendicular semi-infinite wires each give μ0I/4πl at the corner's perpendicular; add as vectors.
Exam Note: Quote the semi-infinite wire result, then √2.
Question 228. Find the magnetic induction at the point O if the wire carrying a current I = 8.0 A has the shape shown in Fig. 3.63 a, b, c. The radius of the curved part of the wire is R = 100 mm, the linear parts of the wire are very long. (The wire is made of straight parts in the xy-plane and a semicircle or circle of radius R in the yz-plane; in (c) the circle is a ring whose two arcs, of lengths in the ratio 1 : 3, are connected in parallel and have equal cross-section and material.)
Solution. (a) B0 = B1 + B2 + B3 = (μ0/4π)(I/R)(−k) + (μ0/4π)(I/R)π(−i) + (μ0/4π)(I/R)(−k) = −(μ0/4π)(I/R)[2k + πi].
So |B0| = (μ0/4π)(I/R)√(π2 + 4) = 30 μT.
Corrected: the book prints 0.30 μT; with μ0I/(4πR) = 8.0 μT the value is 8.0 × 3.72 ≈ 30 μT.
(b) B0 = (μ0/4π)(I/R)(−k) + (μ0/4π)(I/R)π(−i) + (μ0/4π)(I/R)(−i) = −(μ0/4π)(I/R)[k + (π + 1)i].
So |B0| = (μ0/4π)(I/R)√(1 + (π + 1)2) = 34 μT.
Corrected: the book prints 0.34 μT; the correct value is 34 μT.
(c) Using the law of parallel resistances, I1 + I2 = I and I1/I2 = 1/3, so (I1 + I2)/I2 = 4/3, giving I2 = (3/4)I and I1 = (1/4)I. Thus
B0 = (μ0/4π)(I/R)(−k) + (μ0/4π)(I/R)(−j) + [(μ0/4π)(3π/2)(I1/R)(−i) + (μ0/4π)((π/2)I2/R)i].
The two arc terms are equal and opposite (3π/2 · I/4 = π/2 · 3I/4), so they cancel and B0 = −(μ0/4π)(I/R)(j + k).
Thus |B0| = (μ0/4π)(√2 I/R) = 11 μT.
Corrected: the book prints 0.11 μT; the correct value is 11 μT.
Teacher's Note: Add vector contributions with unit vectors; in (c) the current divides inversely as arc length and the arcs cancel.
Exam Note: Final magnitudes: 30 μT, 34 μT, 11 μT.
Question 229. Find the magnitude and direction of the magnetic induction vector B (a) of an infinite plane carrying a current of linear density i; the vector i is the same at all points of the plane; (b) of two parallel infinite planes carrying currents of linear densities i and −i; the vectors i and −i are constant at all points of the corresponding planes.
Solution. (a) Apply the circulation theorem to a rectangular loop of side l, perpendicular to the current and symmetric about the plane. The current in the plane flows (say) vertically upwards, and the magnetic field is horizontal and parallel to the plane, directed oppositely on the two sides. Then
∮B·dl = 2Bl = μ0il, or B = μ0i/2.
(b) Each plane contributes μ0i/2. Between the planes the two fields add and outside the planes they cancel. Thus
B = μ0i between the planes, B = 0 outside.
Teacher's Note: Ampere loop symmetric about the sheet gives μ0i/2; opposite currents add between, cancel outside.
Exam Note: Sketch the loop and field directions.
Question 230. A uniform current of density j flows inside an infinite plate of thickness 2d parallel to its surface. Find the magnetic induction induced by this current as a function of the distance x from the median plane of the plate. The magnetic permeability is assumed to be equal to unity both inside and outside the plate.
Solution. Assume the current flows perpendicular to the plane of the paper. Take a rectangular loop symmetric about the median plane (x = 0). By the circulation theorem, inside the plate 2B dl = μ0(2x dl) j, or
B = μ0jx, for |x| ≤ d.
Outside the plate, 2B dl = μ0(2d dl) j, or
B = μ0jd, for |x| ≥ d.
(The field is directed oppositely on the two sides of the median plane, so B changes sign with x.)
Teacher's Note: Enclosed current grows with |x| inside the plate, then saturates at 2dj per unit length.
Exam Note: Give both ranges, |x| ≤ d and |x| ≥ d.
Question 231. A direct current I flows along a lengthy straight wire. From the point O (Fig. 3.64) the current spreads radially all over an infinite conducting plane perpendicular to the wire. Find the magnetic induction at all points of space.
Solution. There can only be a circuital magnetic field (component Bφ) both in region 1 (on the side of the plane where the wire is) and in region 2 (the other side). Any radial field in region 1 or any Bz away from the current plane would violate Gauss' law of magnetostatics; Bφ must obviously be symmetrical about the straight wire. Then in region 1, taking a circle of radius r around the wire,
Bφ · 2πr = μ0I, or Bφ = μ0I/(2πr).
In region 2 no current passes through the circle, so Bφ · 2πr = 0, or Bφ = 0.
Teacher's Note: Symmetry and ∇·B = 0 leave only Bφ; Ampere's law then depends on enclosed current alone.
Exam Note: State why B is azimuthal before applying Ampere.
Question 232. A current I flows along a round loop. Find the integral ∫B·dr along the axis of the loop within the range from −∞ to +∞. Explain the result obtained.
Solution. On the axis, B = Bx = μ0IR2/(2(R2 + x2)3/2), along the axis. Thus
∫B·dr = ∫−∞∞ Bx dx = (μ0IR2/2) ∫−∞∞ dx/(R2 + x2)3/2
= (μ0IR2/2) ∫−π/2π/2 R sec2θ dθ/(R3 sec3θ), on putting x = R tan θ,
= (μ0I/2) ∫−π/2π/2 cos θ dθ = μ0I.
Physical interpretation: ∫Bxdx can be thought of as the circulation of B over a closed loop, by imagining that the two ends of the axis are connected by a line at infinity (e.g. a semicircle of infinite radius), where B vanishes. The loop encloses the current I, so the circulation is μ0I.
Teacher's Note: Substitution x = R tan θ gives μ0I; it equals the circulation theorem for a loop closed at infinity.
Exam Note: Mention that B falls to zero at infinity.
Question 233. A direct current of density j flows along a round uniform straight wire with cross-section radius R. Find the magnetic induction vector of this current at the point whose position relative to the axis of the wire is defined by a radius vector r. The magnetic permeability is assumed to be equal to unity throughout all the space.
Solution. By the circulation theorem, inside the conductor (r < R): Bφ · 2πr = μ0jzπr2, or Bφ = μ0jzr/2, i.e. B = (1/2)μ0 j × r.
Similarly outside the conductor (r > R): Bφ · 2πr = μ0jzπR2, or Bφ = (1/2)μ0jzR2/r. So B = (1/2)μ0(j × r) R2/r2.
Teacher's Note: Inside, enclosed current ∝ r2 so B ∝ r; outside it is fixed so B ∝ 1/r.
Exam Note: Give inside and outside results separately.
Question 234. Inside a long straight uniform wire of round cross-section there is a long round cylindrical cavity whose axis is parallel to the axis of the wire and displaced from the latter by a distance l. A direct current of density j flows along the wire. Find the magnetic induction inside the cavity. Consider, in particular, the case l = 0.
Solution. The given current, assumed uniform, can be thought of as the true (full-wire) current with a negative current of the same density flowing in the cavity, superimposed everywhere including the cavity. Let A and B be the axes of the wire and of the cavity, and P a point in the cavity. From the previous problem, by superposition,
B = (1/2)μ0 j × (AP − BP) = (1/2)μ0 j × l, where l = AB.
So the field in the cavity is uniform. If l = 0, so that the cavity is concentric with the conductor, there is no magnetic field in the cavity.
Teacher's Note: Full wire plus a reverse-current cylinder; the position-dependent parts cancel, leaving a uniform field.
Exam Note: Quote the superposition idea and the l = 0 case.
Question 235. Find the current density as a function of distance r from the axis of a radially symmetrical parallel stream of electrons if the magnetic induction inside the stream varies as B = brα, where b and α are positive constants.
Solution. By the circulation theorem, Bφ · 2πr = μ0 ∫0r j(r′) 2πr′ dr′. Using Bφ = brα inside the stream,
brα+1 = μ0 ∫0r j(r′) r′ dr′.
Differentiating, (α + 1)brα = μ0 j(r) r. Hence
j(r) = (b(α + 1)/μ0) rα−1.
Teacher's Note: Differentiate Ampere's law with respect to r to recover j(r) from B(r).
Exam Note: Check: α = 1 gives uniform j = 2b/μ0.
Question 236. A single-layer coil (solenoid) has length l and cross-section radius R. A number of turns per unit length is equal to n. Find the magnetic induction at the centre of the coil when a current I flows through it.
Solution. On the surface of the solenoid there is a surface current density js = nI eφ. Then
B = −(μ0/4π) nI ∫ R dφ dz (eφ × r0)/r03,
where r0 is the vector from the current element to the field point, the centre of the solenoid. Now −eφ × r0 = R ez and r0 = (z2 + R2)1/2. Thus B = Bz = (μ0nI/4π) × 2πR2 ∫−l/2l/2 dz/(R2 + z2)3/2
= (1/2)μ0nI ∫−tan⁻¹(l/2R)+tan⁻¹(l/2R) cos α dα (on putting z = R tan α)
= μ0nI sin α = μ0nI (l/2)/√((l/2)2 + R2) = μ0nI/√(1 + (2R/l)2).
Teacher's Note: Treat each turn as a ring and integrate the axial-ring formula; for l ≫ R it tends to μ0nI.
Exam Note: Give the long-solenoid limit as a check.
Question 237. A very long straight solenoid has a cross-section radius R and n turns per unit length. A direct current I flows through the solenoid. Suppose that x is the distance from the end of the solenoid, measured along its axis. Find: (a) the magnetic induction B on the axis as a function of x; draw an approximate plot of B vs the ratio x/R; (b) the distance x0 to the point on the axis at which the value of B differs by η = 1% from that in the middle section of the solenoid.
Solution. We proceed exactly as in the previous problem. (a) The magnetic induction on the axis at a distance x from one end is
B = (μ0nI/4π) × 2πR2 ∫0∞ dz/[R2 + (z − x)2]3/2 = (1/2)μ0nIR2 ∫x∞ dz/(z2 + R2)3/2
= (1/2)μ0nI ∫tan⁻¹(x/R)π/2 cos θ dθ = (1/2)μ0nI (1 − x/√(x2 + R2)).
Here x > 0 means the field point is outside the solenoid, and B falls with x. x < 0 means the field point is inside the solenoid; B then increases with |x| and eventually becomes constant, equal to μ0nI. The B–x graph is shown below.
(b) We have (B0 − δB)/B0 = (1/2)[1 − x0/√(R2 + x02)] = 1 − η, or −x0/√(R2 + x02) = 1 − 2η. Since η is small (≈ 1%), x0 must be negative, x0 = −|x0|. And |x0|/√(R2 + |x0|2) = 1 − 2η, so |x0|2 = (1 − 4η + 4η2)(R2 + |x0|2), i.e. 0 = (1 − 2η)2R2 − 4η(1 − η)|x0|2. Or
|x0| = (1 − 2η)R/(2√(η(1 − η))) ≈ 4.9R for η = 0.01,
i.e. the point lies inside the solenoid at this distance from the end.
Teacher's Note: End-field is half the middle value; use (1/2)(1 ∓ x/√(x2+R2)) and solve for the 1% point.
Exam Note: Quote B = μ0nI/2 at the end.
Question 238. A thin conducting strip of width h = 2.0 cm is tightly wound in the shape of a very long coil with cross-section radius R = 2.5 cm to make a single-layer straight solenoid. A direct current I = 5.0 A flows through the strip. Find the magnetic induction inside and outside the solenoid as a function of the distance r from its axis.
Solution. If the strip is tightly wound, it must have a pitch of h. This means that the current flows obliquely, partly along eφ and partly along ez. Obviously, the surface current density is
Js = (I/h)[√(1 − (h/2πR)2) eφ + (h/2πR) ez].
By comparison with the case of a solenoid and a hollow straight conductor, the field inside the coil is B = μ0(I/h)√(1 − (h/2πR)2) (cf. B = μ0nI), uniform for r < R. This is about 0.31 mT.
Outside, only the other term (the axial current) contributes, so Bφ · 2πr = μ0(I/h)(h/2πR) × 2πR = μ0I, or Bφ = (μ0/4π)(2I/r) = μ0I/(2πr), i.e. B ≈ 1.0 μT·m / r for r > R.
Note: surface current density is defined as the current flowing normally across a unit length over a surface.
Teacher's Note: Resolve the strip current into azimuthal (solenoid-like) and axial (straight-wire-like) parts.
Exam Note: Inside: only azimuthal part; outside: only axial part.
Question 239. N = 2.5·103 wire turns are uniformly wound on a wooden toroidal core of very small cross-section. A current I flows through the wire. Find the ratio η of the magnetic induction inside the core to that at the centre of the toroid.
Solution. Suppose a is the radius of cross-section of the core and R the radius of the toroid. The winding has a pitch 2πR/N, so the surface current density is
Js = (I/(2πR/N)) e1 + (I/(2πa)) e2,
where e1 is a unit vector along the cross-section of the core and e2 a unit vector along its length. The magnetic field inside the core is due to the first term, with total current NI: Bφ · 2πR = μ0NI, so Bφ = μ0NI/(2πR).
The field at the centre of the toroid is due to the second term (current I flowing round the toroid's circumference), from dB = (μ0/4π)(Js × r0)/r03 dS: Bz = (μ0/4π)(I/(2πa)) ∫(1/R3) R dφ × 2πa, or Bz = μ0I/(2R).
The ratio of the two fields is η = N/π ≈ 8·102.
Teacher's Note: Inside field from Ampere's law with NI enclosed; centre field is that of one circular loop carrying I.
Exam Note: N/π = 2500/π ≈ 800.
Question 240. A direct current I = 10 A flows in a long straight round conductor. Find the magnetic flux through a half of wire's cross-section per one metre of its length.
Solution. We need the flux through the shaded area, the half-plane section of the wire (length 1 m, from the axis out to the surface r = R) containing the axis. By Ampere's theorem, Bφ 2πr = μ0(I/πR2)πr2, or Bφ = (μ0/2π) I r/R2. The flux through the shaded region is
Φ1 = ∫0R 1·dr·Bφ(r) = ∫0R (μ0/2π) I (r/R2) dr = μ0I/(4π) = 1.0 μWb.
Teacher's Note: Field inside the wire grows linearly with r; the flux through the axial half-plane is independent of R.
Exam Note: Result μ0I/4π is independent of wire radius.
Question 241. A very long straight solenoid carries a current I. The cross-sectional area of the solenoid is equal to S, the number of turns per unit length is equal to n. Find the flux of the vector B through the end plane of the solenoid.
Solution. Using Q. 237, the magnetic field on the axis is B = (1/2)μ0nI (1 − x/√(x2 + R2)). At the end (x = 0), B = (1/2)μ0nI = B0/2, where B0 = μ0nI is the field deep inside the solenoid. Thus
Φ = (1/2)μ0nIS = Φ0/2, where Φ0 = μ0nIS
is the flux of the vector B through the cross-section deep inside the solenoid.
Teacher's Note: Half the flux leaks out through the sides; end flux equals half the interior flux.
Exam Note: Link back to the end-field B0/2 from Q. 237.
Question 242. Fig. 3.65 shows a toroidal solenoid whose cross-section is rectangular. Find the magnetic flux through this cross-section if the current through the winding equals I = 1.7 A, the total number of turns is N = 1000, the ratio of the outside diameter to the inside one is η = 1.6, and the height is equal to h = 5.0 cm.
Solution. By the circulation theorem, Bφ 2πr = μ0NI, or Bφ = μ0NI/(2πr). Then, for a ≤ r ≤ b,
Φ = ∫ab Bφ h dr = (μ0/4π) 2NIh ln η, where η = b/a.
Numerically, Φ = 2×10−7 × 1000 × 1.7 × 0.05 × ln 1.6 ≈ 8.0 μWb.
Teacher's Note: Field varies as 1/r across the section, so the flux needs integration, giving a logarithm of b/a.
Exam Note: Write η = b/a, then substitute numbers.
Question 243. Find the magnetic moment of a thin round loop with current if the radius of the loop is equal to R = 100 mm and the magnetic induction at its centre is equal to B = 6.0 μT.
Solution. The magnetic moment of a current loop is given by pm = nIS (where n is the number of turns and S the cross-sectional area). Here n = 1, S = πR2 and B = μ0I/(2R). So
pm = (2BR/μ0)πR2 = 2πBR3/μ0 = 30 mA·m2.
Teacher's Note: Eliminate I between B = μ0I/2R and pm = Iπ R2.
Exam Note: Final: 2πBR3/μ0 ≈ 3.0×10−2 A·m2.
Question 244. Calculate the magnetic moment of a thin wire with a current I = 0.8 A, wound tightly on half a tore (Fig. 3.66). The diameter of the cross-section of the tore is equal to d = 5.0 cm, the number of turns is N = 500.
Solution. Take an element of length r dθ containing (N/πr)·r dθ = (N/π)dθ turns. Its magnetic moment is (N/π)dθ · (π/4)d2I, directed normal to the plane of the cross-section. Resolve it along OA and OB, as shown in the figure. The moment along OA integrates to
∫0π (N/4)d2I cos θ dθ = 0,
while that along OB gives
pm = ∫0π (Nd2I/4) sin θ dθ = (1/2)Nd2I = 0.5 A·m2.
Teacher's Note: Each turn's moment is Iπd²/4; only components along one axis survive the θ integration.
Exam Note: Show the cos θ term vanishing.
Question 245. A thin insulated wire forms a plane spiral of N = 100 tight turns carrying a current I = 8 mA. The radii of inside and outside turns (Fig. 3.67) are equal to a = 50 mm and b = 100 mm. Find: (a) the magnetic induction at the centre of the spiral; (b) the magnetic moment of the spiral with a given current.
Solution. (a) By the Biot-Savart law, the induction at the centre of a circular loop of radius r is Br = μ0I/(2r). The plane spiral is made up of concentric circular loops of radii from a to b, so
B0 = ∫(μ0I/2r) dN, where dN = (N/(b − a)) dr is the number of turns in the interval (r, r + dr).
Hence B0 = ∫ab (μ0I/2r)(N/(b − a)) dr = (μ0IN/(2(b − a))) ln(b/a) ≈ 7.0 μT.
(b) The magnetic moment of a turn of radius r is pm = Iπr2, and of all turns,
p = ∫pm dN = ∫ab Iπr2 (N/(b − a)) dr = πIN(b3 − a3)/(3(b − a)) ≈ 15 mA·m2.
Corrected: the book prints (b3 − a2) in the last expression; the integral of r2 gives (b3 − a3)/3, as written above.
Teacher's Note: Treat the spiral as concentric rings with uniform turn density dN = N dr/(b − a).
Exam Note: Integrate rings; B gives ln(b/a), moment gives r2.
Question 246. A non-conducting thin disc of radius R charged uniformly over one side with surface density σ rotates about its axis with an angular velocity ω. Find: (a) the magnetic induction at the centre of the disc; (b) the magnetic moment of the disc.
Solution. (a) Take a ring element of radius r and thickness dr. The charge on it is dq = σ·2πr dr, and the current due to this element is dI = (σ 2πr dr)ω/2π = σωr dr. The magnetic induction at the centre due to this element is dB = (μ0/2)(dI/r). Hence, from symmetry,
B = ∫dB = ∫0R μ0σω r dr/(2r) = (μ0/2)σωR.
(b) The magnetic moment of the element is dpm = (dI)πr2 = σω dr πr2 = σπω r3 dr. Hence the magnetic moment is
pm = ∫dpm = ∫0R σπω r3 dr = σωπR4/4.
Teacher's Note: Split the disc into rings; each ring is a current loop with dI = σωr dr.
Exam Note: Integrate rings for both B and pm.
Question 247. A non-conducting sphere of radius R = 50 mm charged uniformly with surface density σ = 10.0 μC/m2 rotates with an angular velocity ω = 70 rad/s about the axis passing through its centre. Find the magnetic induction at the centre of the sphere.
Solution. As only the outer surface of the sphere is charged, consider a ring element on the surface at polar angle θ from the axis, of radius R sin θ and width R dθ. Its equivalent current is
dI = (ω/2π)(2πR sin θ · R dθ) σ = σωR2 sin θ dθ.
Using the result of Q. 219 (b) for the field of a ring at a point on its axis, the induction at the centre O from this ring is dB = μ0 dI (R sin θ)2/(2R3) = μ0 dI sin2θ/(2R). Hence the total induction at O is
B = ∫0π (μ0σωR/2) sin3θ dθ = (2/3)μ0σωR ≈ 29 pT.
Corrected: some intermediate lines of the book's working carry a missing numerical factor (they integrate sin3θ over 0 to π/2 with the wrong prefactor); the final result (2/3)μ0σωR = 29 pT is right and the working above gives it consistently.
Teacher's Note: Slice the sphere into rings parallel to the equator; ∫sin3θ dθ over 0 to π equals 4/3.
Exam Note: Use the axial ring formula, then integrate over θ.
Question 248. A charge q is uniformly distributed over the volume of a uniform ball of mass m and radius R which rotates with an angular velocity ω about the axis passing through its centre. Find the respective magnetic moment and its ratio to the mechanical moment.
Solution. The magnetic moment must clearly be along the axis of rotation. Consider a volume element dV at distance r from the centre and polar angle θ. It contains a charge (q/((4π/3)R3)) dV = (3q/(4πR3)) dV. The rotation of the sphere causes this charge to revolve about the axis and constitute a current (3q/(4πR3)) dV × ω/2π. Its magnetic moment is (3q/(4πR3)) dV × (ω/2π) × πr2 sin2θ. So the total magnetic moment is
pm = ∫0R∫0π (3q/(2R3)) r2 sin θ dθ (ωr2 sin2θ/2) dr = (3q/(2R3)) × (ω/2) × (R5/5) × (4/3) = (1/5)qR2ω.
The mechanical moment (angular momentum) is M = (2/5)mR2ω. So
pm/M = q/(2m).
Teacher's Note: Integrate ring-moments over the volume; the ratio q/2m is the classical gyromagnetic ratio.
Exam Note: Use I = (2/5)mR2 for a uniform ball.
Question 249. A long dielectric cylinder of radius R is statically polarized so that at all its points the polarization is equal to P = αr, where α is a positive constant, and r is the distance from the axis. The cylinder is set into rotation about its axis with an angular velocity ω. Find the magnetic induction B at the centre of the cylinder.
Solution. Because of polarization a space charge is present within the cylinder. Its density is ρp = −div P = −2α. Since the cylinder as a whole is neutral, a surface charge density σp must be present on its surface also. Algebraically, σp × 2πR = 2απR2, or σp = αR.
When the cylinder rotates, currents are set up which give rise to magnetic fields. The contributions of ρp and σp can be calculated separately and then added.
Surface charge: for a particular element of length dx the current is αR × 2πR dx × ω/2π = αR2ω dx. Its contribution to the field at the centre is μ0R2(αR2ω dx)/(2(x2 + R2)3/2). The total field is
Bs = ∫−∞∞ μ0R2(αR2ω dx)/(2(x2 + R2)3/2) = (μ0αR4ω/2) × 2/R2 = μ0αR2ω.
Volume charge: consider a ring of radius r, radial thickness dr and length dx. The current is −2α × 2πr dr dx × ω/2π = −2αrω dr dx. The total field due to the volume charge is
Bv = −∫0R dr ∫−∞∞ dx 2αrω μ0r2/(2(x2 + r2)3/2) = −∫0R αμ0ω r3 dr ∫ dx/(x2 + r2)3/2 = −∫0R αμ0ωr dr × 2 = −μ0αωR2.
So B = Bs + Bv = 0.
Teacher's Note: Bound surface charge and negative volume charge rotate; their axial fields are equal and opposite.
Exam Note: Find ρp = −div P and σp first.
Question 250. Two protons move parallel to each other with an equal velocity v = 300 km/s. Find the ratio of forces of magnetic and electrical interaction of the protons.
Solution. Force of magnetic interaction, Fmag = e(v × B), where B = (μ0/4π) e(v × r)/r3. So
Fmag = (μ0/4π)(e2/r3)[v × (v × r)] = (μ0/4π)(e2/r3)[(v·r)v − (v·v)r] = (μ0/4π)(e2/r3)(−v2r), since v ⊥ r.
And Fele = eE = e (1/4πε0) er/|r|3. Hence the magnitudes are in the ratio
Fmag/Fele = v2μ0ε0 = (v/c)2 = 1.00×10−6.
(The magnetic force is attractive while the electric force is repulsive, which is why the book shows a minus sign.)
Teacher's Note: Ratio reduces to (v/c)2 since μ0ε0 = 1/c2; magnetic force is tiny at low speed.
Exam Note: v/c = 10−3, so the ratio is 10−6.
Question 251. Find the magnitude and direction of a force vector acting on a unit length of a thin wire, carrying a current I = 8.0 A, at a point O, if the wire is bent as shown in (a) Fig. 3.68a, with curvature radius R = 10 cm; (b) Fig. 3.68b, the distance between the long parallel segments of the wire being equal to l = 20 cm. (In (a), the wire is a semicircle of radius R with straight segments continuing along the diameter, O being the centre, on the straight segment; in (b), two long parallel segments joined at the left end by a perpendicular segment, O being at the middle of the perpendicular segment.)
Solution. (a) The magnetic field at O is only due to the curved path, since for the straight line elements dl ∥ r. Taking x to the right, y up and z towards the viewer (out of the page), the current goes clockwise round the semicircle, so
B = (μ0I/4πR) π (−k) = (μ0I/4R)(−k).
Thus the force per unit length is Fu = I B (−j) = (μ0I2/4R)(−j), so Fu = μ0I2/(4R) = 0.20 mN/m, directed along −y (away from the semicircle).
Corrected: the book prints 0.20 N/m; μ0I2/(4R) = (4π×10−7 × 64)/(0.4) = 2.0×10−4 N/m = 0.20 mN/m.
(b) Here the magnetic induction at O is effective only due to the two semi-infinite segments of wire. Hence
B = 2 · (μ0I/(4π(l/2))) sin(π/2) (−k) = (μ0I/(πl))(−k).
Thus the force per unit length is Fu = (μ0I2/(πl))(−i), of magnitude μ0I2/(πl) = 0.13 mN/m, directed along −x (away from the loop).
Teacher's Note: Force per unit length is IB, B from the rest of the circuit; direction from I dl × B.
Exam Note: Straight segments give zero field at O.
Download IE Irodov Solutions for JEE Math PDF
Download IE Irodov Solutions for JEE
Review detailed solutions for JEE Mathematics. The IE Irodov Solutions Chapter 20 Constant Magnetic Field Magnetics Part 1 PDF provides comprehensive answers mapped to standard IE Irodov Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Mastering Core Concepts with IE Irodov Solutions
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Additional Study Materials for 2026
Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.
FAQs
They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.