IE Irodov Solutions Chapter 19 Electric Current Part 2

Download JEE Physics IE Irodov Textbook Solutions: Chapter 19 Electric Current

Review structured textbook solutions for JEE Physics Chapter 19 Electric Current prepared by IE Irodov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.

Access IE Irodov Textbook Answers and Solutions

Access the complete solution PDF for JEE Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.

Electric Current - Questions 184 to 218

Electric Current (Part - 3)

Question 184. Find a potential difference φA − φB between the plates of a capacitor C in the circuit shown in Fig. 3.47 if the sources have emf's ε1 = 4.0 V and ε2 = 1.0 V and the resistances are equal to R1 = 10 Ω, R2 = 20 Ω, and R3 = 30 Ω. The internal resistances of the sources are negligible.
R₃CABε₂R₂R₁ε₁+i₁ ↓i₃ →(i₁ − i₃)

Fig. 3.47: R3 and capacitor C in the top branch, ε2 in the middle vertical branch, R2 and R1 in the middle horizontal branch, ε1 in the bottom branch. Currents are marked as used in the solution.

Solution.

Indicate the currents in all the branches using charge conservation as shown in the figure (no current flows through the capacitor in the steady state). Applying the loop rule (−Δφ = 0) in the loops 12341 and 15781, we get

−ε1 + i3R1 − (i1 − i3)R2 = 0   (1)

and (i1 − i3)R2 − ε2 + i1R3 = 0   (2)

Solving Eqs. (1) and (2), we get

i3 = [ε1(R2 + R3) + ε2R2] / (R1R2 + R2R3 + R3R1)

Hence, the sought p.d.

φA − φB = ε2 − i3R1 = [ε2R3(R1 + R2) − ε1R1(R2 + R3)] / (R1R2 + R2R3 + R3R1) = −1 V

Teacher's Note: A capacitor carries no steady current, so solve the resistor loops first, then read the p.d. across C.

Exam Note: Show both loop equations; sign of the answer matters.

Question 185. Find the current flowing through the resistance R1 of the circuit shown in Fig. 3.48 if the resistances are equal to R1 = 10 Ω, R2 = 20 Ω, R3 = 30 Ω, and the potentials of points 1, 2, and 3 are equal to φ1 = 10 V, φ2 = 6 V, and φ3 = 5 V.
1R₁Ai →R₂R₃23i₁i − i₁

Fig. 3.48: R1 joins point 1 to the junction A; R2 and R3 join A to points 2 and 3.

Solution.

Let us distribute the currents in the paths as shown in the figure.

Now, φ1 − φ2 = iR1 + i1R2   (1)

and φ1 − φ3 = iR1 + (i − i1)R3   (2)

Simplifying Eqs. (1) and (2) we get

i = [R3(φ1 − φ2) + R2(φ1 − φ3)] / (R1R2 + R2R3 + R3R1) = 0.2 A

Teacher's Note: Three-terminal star: write potential drops from point 1 to points 2 and 3 and eliminate i1.

Exam Note: Substitute numbers last; state unit A.

Question 186. A constant voltage V = 25 V is maintained between points A and B of the circuit (Fig. 3.49). Find the magnitude and direction of the current flowing through the segment CD if the resistances are equal to R1 = 1.0 Ω, R2 = 2.0 Ω, R3 = 3.0 Ω, and R4 = 4.0 Ω.
AR₁R₃CDR₂R₄Bi₁i₂i₃ ↓i₁ − i₃i₂ + i₃

Fig. 3.49: R1 and R2 in the upper branch, R3 and R4 in the lower branch, C and D (between the resistors) joined by a wire. Currents are marked as used in the solution.

Solution.

Current is as shown. From Kirchhoff's second law

i1R1 = i2R3,

i1R1 + (i1 − i3)R2 = V,

i2R3 + (i3 + i2)R4 = V.

Eliminating i2:

i1(R1 + R2) − i3R2 = V

i1(R1/R3)(R3 + R4) + i3R4 = V

Hence

i3 = V[R3(R1 + R2) − R1(R3 + R4)] / [R3R4(R1 + R2) + R1R2(R3 + R4)]

On substitution we get i3 = 1.0 A from C to D.

Teacher's Note: A zero-resistance wire CD makes C and D equipotential, which gives i1R1 = i2R3.

Exam Note: Mark direction C to D with the number.

Question 187. Find the resistance between points A and B of the circuit shown in Fig. 3.50.
ArRRrrB

Fig. 3.50: upper branch r then R, lower branch R then r, and a middle resistor r joining the two mid-points.

Solution.

From the symmetry of the problem, current flow is as indicated in the figure: current i enters at A, i1 goes through the upper left r, (i − i1) through the lower left R, (i − 2i1) through the middle r (directed from node 2 up to node 5), (i − i1) through the upper right R and i1 through the lower right r.

Now, φA − φB = i1r + (i − i1)R   (1)

In the loop 12561, from −Δφ = 0:

(i − i1)R + (i − 2i1)r − i1r = 0

or, i1 = [(R + r)/(3r + R)] i   (2)

Equivalent resistance between the terminals A and B using (1) and (2):

R0 = (φA − φB)/i = {[(R + r)/(3r + R)](r − R) + R} = r(3R + r)/(3r + R)

Teacher's Note: Use the circuit symmetry to cut the unknown currents to one, then apply the loop rule.

Exam Note: Give the final form r(3R+r)/(R+3r).

Question 188. Find how the voltage across the capacitor C varies with time t (Fig. 3.51) after the shorting of the switch Sw at the moment t = 0.
εRRCSw

Fig. 3.51: source ε, switch Sw and resistor R in series, feeding a parallel combination of another resistor R and the capacitor C.

Solution.

Let, at any moment of time, the charge on the plates be +q and −q respectively; then the voltage across the capacitor is φ = q/C   (1)

From charge conservation, i = i1 + i2, where i2 = dq/dt   (2)

In the loop 65146, using −Δφ = 0:

q/C + (i1 + dq/dt)R − ε = 0   (3) [using (1) and (2)]

In the loop 25632, using −Δφ = 0:

−q/C + i1R = 0, or i1R = q/C   (4)

From (3) and (4):

R dq/dt = ε − 2q/C, or dq/(ε − 2q/C) = dt/R   (5)

On integrating expression (5) between suitable limits,

∫0q dq/(ε − 2q/C) = (1/R)∫0t dt, or −(C/2) ln[(ε − 2q/C)/ε] = t/R

Thus V = q/C = (ε/2)(1 − e−2t/RC)

Teacher's Note: The parallel R and C give a charging equation with time constant RC/2 and final voltage ε/2.

Exam Note: Quote V = (ε/2)(1 − e^(−2t/RC)); check t = 0 gives zero.

Question 189. What amount of heat will be generated in a coil of resistance R due to a charge q passing through it if the current in the coil
(a) decreases down to zero uniformly during a time interval Δt;
(b) decreases down to zero halving its value every Δt seconds?
Solution.

(a) As current i is a linear function of time, and at t = 0 and Δt it equals i0 and zero respectively, it may be represented as i = i0(1 − t/Δt).

Thus q = ∫0Δt i dt = ∫0Δt i0(1 − t/Δt) dt = i0Δt/2. So, i0 = 2q/Δt. Hence, i = (2q/Δt)(1 − t/Δt).

The heat generated: H = ∫0Δt i2R dt = ∫0Δt [(2q/Δt)(1 − t/Δt)]2 R dt = 4q2R/(3Δt)

(b) Obviously the current through the coil is given by i = i0(1/2)t/Δt.

Then charge q = ∫0∞ i dt = ∫0∞ i02−t/Δt dt = i0Δt/ln 2. So, i0 = q ln 2/Δt.

And hence, the heat generated in the circuit in the time interval t [0, ∞]:

H = ∫0∞ i2R dt = ∫0∞ [(q ln 2/Δt) 2−t/Δt]2 R dt = q2R ln 2/(2Δt)

Teacher's Note: Fix i0 from the given charge first, then integrate i2R over time.

Exam Note: Total heat needs q and Δt, not i0.

Question 190. A d.c. source with internal resistance R0 is loaded with three identical resistances R interconnected as shown in Fig. 3.52. At what value of R will the thermal power generated in this circuit be the highest?

Fig. 3.52: three resistors R in a chain, with two connecting wires that make all three effectively connected in parallel across the source (equivalent circuit shown below).

RRRε, R₀
Solution.

The equivalent circuit may be drawn as in the figure: the three resistors R are in parallel and connected across the source.

Resistance of the network = R0 + (R/3).

Let us assume the e.m.f. of the cell is ε; then the current i = ε/[R0 + (R/3)].

Now, the thermal power generated in the circuit (in the three resistors) is

P = i2R/3 = ε2/[R0 + (R/3)]2 · (R/3)

For P to be maximum, dP/dR = 0, which yields R = 3R0.

Teacher's Note: Redraw the shorted chain as three parallel R; maximum power transfer needs R/3 = R0.

Exam Note: State R = 3R0 after setting dP/dR = 0.

Question 191. Make sure that the current distribution over two resistances R1 and R2 connected in parallel corresponds to the minimum thermal power generated in this circuit.
R₁R₂ii₁i − i₁
Solution.

We assume current conservation but not Kirchhoff's second law. Then the thermal power dissipated is

P(i1) = i12R1 + (i − i1)2R2

= i12(R1 + R2) − 2ii1R2 + i2R2

= (R1 + R2)[i1 − R2i/(R1 + R2)]2 + i2R1R2/(R1 + R2)

The resistances being positive, we see that the power dissipated is minimum when

i1 = i R2/(R1 + R2)

This corresponds to the usual distribution of currents over resistances joined in parallel.

Teacher's Note: Complete the square in i1; the minimum sits at the parallel-current-divider value.

Exam Note: Show the completed square, not just the result.

Question 192. A storage battery with emf ε = 2.6 V loaded with an external resistance produces a current I = 1.0 A. In this case the potential difference between the terminals of the storage battery equals V = 2.0 V. Find the thermal power generated in the battery and the power developed in it by electric forces.
Solution.

Let the internal resistance of the cell be r, then V = ε − ir   (1), where i is the current in the circuit. The thermal power generated in the battery is Q = i2r   (2).

Putting r from (1) in (2), we obtain Q = (ε − V)i = 0.6 W.

In a battery, work is done by electric forces (whose origin lies in the chemical processes going on inside the cell). The power developed by these forces in the battery is the rate at which they move charge against the potential difference across the emf: P = εI = 2.6 × 1.0 = 2.6 W. (Check: this equals the power delivered to the external resistance, VI = 2.0 W, plus the heat in the battery, 0.6 W.)

Corrected: the printed solution gives P = −IV = −2.0 W, which is the power delivered to the outside circuit, not the power developed by the electric forces in the battery. The correct value is εI = 2.6 W.

Teacher's Note: Terminal voltage drop ε − V = Ir gives heat; total electrical power developed is εI.

Exam Note: Power developed = heat + external power.

Question 193. A voltage V is applied to a d.c. electric motor. The armature winding resistance is equal to R. At what value of current flowing through the winding will the useful power of the motor be the highest? What is it equal to? What is the motor efficiency in this case?
Solution.

As far as the motor is concerned, the power delivered is dissipated and can be represented by a load R0 in series with R, across voltage V. Thus

I = V/(R + R0) and P = I2R0 = V2R0/(R0 + R)2

This is maximum when R0 = R and the current I is then I = V/(2R).

The maximum power delivered is Pmax = V2/(4R).

The power input is V2/(R + R0) and its value when P is maximum is V2/(2R).

The efficiency then is 1/2 = 50%.

Teacher's Note: Treat the back-emf load as R0; maximum power transfer occurs at R0 = R.

Exam Note: Efficiency of maximum useful power is only 50%.

Question 194. How much (in per cent) has a filament diameter decreased due to evaporation if the maintenance of the previous temperature required an increase of the voltage by η = 1.0%? The amount of heat transferred from the filament into surrounding space is assumed to be proportional to the filament surface area.
Solution.

Let the wire diameter decrease by the fraction δ. Then by the information given, the power input P = V2/R = heat lost through the surface, H.

H ∝ (1 − δ), like the surface area, and R ∝ (1 − δ)−2.

So, [V2/R0](1 − δ)2 = A(1 − δ), or V2(1 − δ) = constant.

But V ∝ 1 + η, so (1 + η)2(1 − δ) = const = 1.

Thus δ ≈ 2η = 2%.

Teacher's Note: Resistance rises as (1−δ)−2 while loss area falls as (1−δ); equate to find δ.

Exam Note: Use the small-η approximation; state the answer 2%.

Question 195. A conductor has a temperature-independent resistance R and a total heat capacity C. At the moment t = 0 it is connected to a d.c. voltage V. Find the time dependence of the conductor's temperature T assuming the thermal power dissipated into surrounding space to vary as q = k(T − T0), where k is a constant, T0 is the environmental temperature (equal to the conductor's temperature at the initial moment).
Solution.

The equation of heat balance is V2/R − k(T − T0) = C dT/dt.

Put T − T0 = θ. So, Cθ′ + kθ = V2/R, or θ′ + (k/C)θ = V2/(CR),

or d/dt (θekt/C) = [V2/(CR)] ekt/C,

or θekt/C = (V2/kR) ekt/C + A, where A is a constant.

Clearly θ = 0 at t = 0, so A = −V2/(kR) and hence,

T = T0 + (V2/kR)(1 − e−kt/C)

Teacher's Note: Heat balance gives a first-order linear ODE; integrating factor ekt/C solves it.

Exam Note: Check T(0) = T0 and the limit T0 + V²/kR.

Question 196. A circuit shown in Fig. 3.53 has resistances R1 = 20 Ω and R2 = 30 Ω. At what value of the resistance Rx will the thermal power generated in it be practically independent of small variations of that resistance? The voltage between the points A and B is supposed to be constant in this case.
AR₁R₂RₓB

Fig. 3.53: R1 in series, followed by R2 and Rx in parallel, between A and B.

Solution.

Let φA − φB = φ. Now, the thermal power generated in the resistance Rx is

P = i′2Rx = [φ/(R1 + R2Rx/(R2 + Rx)) · R2/(R2 + Rx)]2 Rx

For P to be independent of Rx (for small variations), dP/dRx = 0, which yields

Rx = R1R2/(R1 + R2) = 12 Ω

Teacher's Note: Power is stationary where Rx equals the equivalent resistance of R1 and R2 in parallel.

Exam Note: Reason via dP/dRx = 0; give 12 Ω.

Question 197. In a circuit shown in Fig. 3.54 resistances R1 and R2 are known, as well as emf's ε1 and ε2. The internal resistances of the sources are negligible. At what value of the resistance R will the thermal power generated in it be the highest? What is it equal to?
ε₁R₁Rε₂R₂123i₁i →i − i₁

Fig. 3.54: three parallel branches between two common wires: (ε1 with R1), R alone, and (ε2 with R2). Currents are marked as used in the solution.

Solution.

Indicate the currents in the circuit as shown in the figure. Applying the loop rule in the closed loop 12561, −Δφ = 0, we get

i1R − ε1 + iR1 = 0   (1)

and in the loop 23452,

(i − i1)R2 + ε2 − i1R = 0   (2)

Solving (1) and (2), we get

i1 = (ε1R2 + ε2R1) / (RR1 + R1R2 + RR2)

So, the thermal power generated in the resistance R is

P = i12R = [(ε1R2 + ε2R1) / (RR1 + R1R2 + RR2)]2 R

For P to be maximum, dP/dR = 0, which yields

R = R1R2/(R1 + R2)

Hence, Pmax = (ε1R2 + ε2R1)2 / [4R1R2(R1 + R2)]

Teacher's Note: Two sources with R1, R2 act as one equivalent source; power peaks when R equals its internal resistance.

Exam Note: Quote both R and Pmax.

Question 198. A series-parallel combination battery consisting of a large number N = 300 of identical cells, each with an internal resistance r = 0.3 Ω, is loaded with an external resistance R = 10 Ω. Find the number n of parallel groups consisting of an equal number of cells connected in series, at which the external resistance generates the highest thermal power.
Solution.

Let there be x cells connected in series in each of the n parallel groups; then nx = N, or x = N/n   (1)

Now, for any one of the loops, consisting of x cells and the resistor R, from the loop rule (each group carries current i/n):

iR + (i/n)xr − xε = 0

So, i = xε / (R + xr/n) = (N/n)ε / (R + Nr/n2), using (1).

Heat generated in the resistor R:

Q = i2R = [Nnε / (n2R + Nr)]2 R   (2) Corrected: the printed denominator n2R + NR is a misprint; simplifying i above gives n2R + Nr, which is used here.

For Q to be maximum, dQ/dn = 0, which yields

n = √(Nr/R) = √(300 × 0.3 / 10) = 3

Teacher's Note: Cells in x-series groups with n groups: power peaks when external R equals battery internal resistance Nr/n2.

Exam Note: Show internal resistance xr/n and n = √(Nr/R).

Question 199. A capacitor of capacitance C = 5.00 μF is connected to a source of constant emf ε = 200 V (Fig. 3.55). Then the switch Sw was thrown over from contact 1 to contact 2. Find the amount of heat generated in a resistance R1 = 500 Ω if R2 = 330 Ω.
CR₂R₁21Swε

Fig. 3.55 (schematic): with the switch at contact 1 the capacitor C (in series with R2) is charged by ε; at contact 2 the capacitor discharges through R2 and R1 in series.

Solution.

When the switch is at 1, the maximum charge accumulated on the capacitor is qmax = Cε   (1)

When the switch is at 2, at any arbitrary instant of time, (R1 + R2)(−dq/dt) = q/C, because the capacitor is discharging.

or, ∫qmaxq dq/q = −[1/((R1 + R2)C)] ∫0t dt

Integrating, we get ln(q/qmax) = −t/((R1 + R2)C), or q = qmax e−t/((R1 + R2)C)   (2)

Differentiating with respect to time, i(t) = dq/dt = qmax e−t/((R1 + R2)C)(−1/((R1 + R2)C)), or, ignoring the sign (direction of current is not needed),

i(t) = [ε/(R1 + R2)] e−t/((R1 + R2)C)   (3)

When the capacitor discharges, the electric energy stored in it turns totally into heat in the resistors R1 and R2 (over a very long time). From energy conservation, the total heat liberated in the resistors is

H = Ui = q2/2C = ½Cε2

During the discharge the same current flows through R1 and R2 at all moments, thus H1 ∝ R1 and H2 ∝ R2. So H1 = HR1/(R1 + R2) (as H = H1 + H2), i.e.

H1 = ½ · CR1ε2/(R1 + R2) = ½ × 5.00×10−6 × 500 × (200)2 / 830 ≈ 0.060 J = 60 mJ

Teacher's Note: Whole stored energy ½Cε² ends as heat, shared between series resistors in ratio R1:R2.

Exam Note: Give the final value in mJ.

Question 200. Between the plates of a parallel-plate capacitor there is a metallic plate whose thickness takes η = 0.60 of the capacitor gap. When that plate is absent the capacitor has a capacity C = 20 nF. The capacitor is connected to a d.c. voltage source V = 100 V. The metallic plate is slowly extracted from the gap. Find:
(a) the energy increment of the capacitor;
(b) the mechanical work performed in the process of plate extraction.
Solution.

When the plate is absent the capacity of the condenser is C = ε0S/d.

When it is present, the capacity is C′ = ε0S/[d(1 − η)] = C/(1 − η).

(a) The energy increment is clearly

ΔU = ½CV2 − ½C′V2 = −[Cη/(2(1 − η))] V2 = −0.15 mJ

(b) The charge on the plates is qi = CV/(1 − η) initially and qf = CV finally. A charge CVη/(1 − η) has flowed through the battery charging it and withdrawing CV2η/(1 − η) units of energy from the system into the battery. The energy of the capacitor has decreased by just half of this. The remaining half, i.e.

A = ½ · CV2η/(1 − η) = 0.15 mJ

must be the work done by the external agent in withdrawing the plate. This ensures conservation of energy.

Corrected: the printed expression for ΔU in (a) lacks the minus sign (the energy decreases, since ½CV2 − ½C′V2 is negative). Numerical values added: ½ × 20×10−9 × 104 × 0.6/0.4 = 0.15 mJ.

Teacher's Note: Battery stays connected: capacitor energy falls by half of what the battery absorbs; the agent supplies the other half.

Exam Note: Note sign of ΔU is negative; work is positive.

Electric Current (Part - 4)

Question 201. A glass plate totally fills up the gap between the electrodes of a parallel-plate capacitor whose capacitance in the absence of that glass plate is equal to C = 20 nF. The capacitor is connected to a d.c. voltage source V = 100 V. The plate is slowly, and without friction, extracted from the gap. Find the capacitor energy increment and the mechanical work performed in the process of plate extraction.
Solution.

Initially, the capacitance of the system = Cε (ε is the dielectric constant of glass; the numerical answer corresponds to ε = 6).

So, the initial energy of the system: Ui = ½(Cε)V2.

And finally, the energy of the capacitor: Uf = ½CV2.

Hence the capacitor energy increment,

ΔU = ½CV2 − ½(Cε)V2 = −½CV2(ε − 1) = −0.5 mJ

From energy conservation ΔU = Acell + Aagent (as there is no heat liberation).

But Acell = (Cf − Ci)V2 = (C − Cε)V2.

Hence Aagent = ΔU − Acell = ½C(ε − 1)V2 = 0.5 mJ

Corrected: the printed final expression ½C(1 − ε)V2 has the wrong sign (it would give −0.5 mJ); ΔU − Acell = +½C(ε − 1)V2 = +0.5 mJ. The problem does not state ε; ε = 6 for glass is assumed, as in the source problem book.

Teacher's Note: Constant V: battery does −C(ε−1)V², capacitor energy changes by half of that; agent does the rest.

Exam Note: State assumed ε = 6; sign of work positive.

Question 202. A cylindrical capacitor connected to a d.c. voltage source V touches the surface of water with its end (Fig. 3.56). The separation d between the capacitor electrodes is substantially less than their mean radius. Find a height h to which the water level in the gap will rise. The capillary effects are to be neglected.
helectrodes (gap d)water surface

Fig. 3.56 (schematic cross-section): the lower end of the vertical cylindrical capacitor dips into water; water rises by h in the gap between the electrodes.

Solution.

If C0 is the initial capacitance of the condenser before water rises in it, then Ui = ½C0V2, where C0 = ε02πRl/d (R is the mean radius and l is the length of the capacitor plates).

Suppose the liquid rises to a height h in it. Then the capacitance of the condenser is

C = εε0h2πR/d + ε0(l − h)2πR/d = (ε02πR/d)(l + (ε − 1)h)

And the energy of the capacitor and the liquid (including both gravitational and electrostatic contributions) is

½(ε02πR/d)(l + (ε − 1)h)V2 + ρg(2πRdh)(h/2)

If the capacitor were not connected to a battery this energy would have to be minimized. But the capacitor is connected to the battery and, in effect, the potential energy of the whole system has to be minimized. Suppose we increase h by δh. Then the energy of the capacitor and the liquid increases by

δh [ (ε02πR/2d)(ε − 1)V2 + ρg(2πRd)h ]

And that of the cell diminishes by the quantity Acell, which is the product of charge flown and V:

δh (ε02πR/d)(ε − 1)V2

In equilibrium, the two must balance; so

ρgdh = ε0(ε − 1)V2/(2d)

Hence h = ε0(ε − 1)V2 / (2ρgd2)

Teacher's Note: With the battery attached, energy of capacitor plus liquid minus battery work is stationary at equilibrium.

Exam Note: Remember the battery term; ε is the water permittivity.

Question 203. The radii of spherical capacitor electrodes are equal to a and b, with a < b. The interelectrode space is filled with homogeneous substance of permittivity ε and resistivity ρ. Initially the capacitor is not charged. At the moment t = 0 the internal electrode gets a charge q0. Find:
(a) the time variation of the charge on the internal electrode;
(b) the amount of heat generated during the spreading of the charge.
Solution.

(a) Let us mentally isolate a thin spherical layer with inner and outer radii r and r + dr respectively. Lines of current at all the points of this layer are perpendicular to it and therefore such a layer can be treated as a spherical conductor of thickness dr and cross-sectional area 4πr2. Now, we know that the resistance

dR = ρ dr/S(r) = ρ dr/(4πr2)   (1)

Integrating expression (1) between the limits, R = ∫ dR = ∫ab ρ dr/(4πr2), or R = (ρ/4π)(1/a − 1/b)   (2)

Capacitance of the network, C = 4πε0ε/(1/a − 1/b)   (3)

And q = Cφ [where q is the charge at any arbitrary moment]   (4)

Also, φ = (−dq/dt)R, as the capacitor is discharging.   (5)

From Eqs. (2), (3), (4) and (5) we get dq/q = −dt/(ρεε0), i.e.

∫q0q dq/q = −(1/ρεε0) ∫0t dt

Integrating, hence q = q0 e−t/(ρε0ε)

(b) From energy conservation, the heat generated during the spreading of the charge is H = Ui − Uf [because Acell = 0]

= (1/2)(q02/(4πε0ε))(1/a − 1/b) − 0 = q02(b − a)/(8πε0ε ab)

Teacher's Note: Spherical resistance and capacitance multiply to ρεε0, independent of radii; heat equals initial energy.

Exam Note: Show RC = ρεε0; heat equals initial stored energy.

Question 204. The electrodes of a capacitor of capacitance C = 2.00 μF carry opposite charges q0 = 1.00 mC. Then the electrodes are interconnected through a resistance R = 5.0 MΩ. Find:
(a) the charge flowing through that resistance during a time interval τ = 2.00 s;
(b) the amount of heat generated in the resistance during the same interval.
Solution.

(a) Let, at any moment of time, the charge on the plates be (q0 − q); then the current through the resistor is i = −d(q0 − q)/dt, because the capacitor is discharging. Or, i = dq/dt.

Now, applying the loop rule in the circuit, iR − (q0 − q)/C = 0.

Or, R dq/dt = (q0 − q)/C. Or, dq/(q0 − q) = dt/(RC).

At t = 0, q = 0 and at t = τ, q = q. So, ln[(q0 − q)/q0] = −τ/(RC).

Thus q = q0(1 − e−τ/RC) = 0.18 mC

(b) The amount of heat generated = decrement in capacitor energy

= ½q02/C − ½[q0 − q0(1 − e−τ/RC)]2/C = ½(q02/C)[1 − e−2τ/RC] = 82 mJ

Teacher's Note: Time constant RC = 10 s; charge passed is q0(1 − e−τ/RC), heat is the energy drop.

Exam Note: Compute RC first; keep units mC and mJ.

Question 205. In a circuit shown in Fig. 3.57 the capacitance of each capacitor is equal to C and the resistance, to R. One of the capacitors was connected to a voltage V0 and then at the moment t = 0 was shorted by means of the switch Sw. Find:
(a) a current I in the circuit as a function of time t;
(b) the amount of generated heat provided a dependence I(t) is known.
CSwRC

Fig. 3.57: two capacitors C joined by a resistor R in the upper wire and a switch Sw in the lower wire.

Solution.

(a) Let, at any moment of time, the charge flown be q; then the current i = dq/dt. Applying the loop rule in the circuit, −Δφ = 0, we get (the capacitor that was charged to V0 has charge CV0 − q, the other has q):

iR − (CV0 − q)/C + q/C = 0, i.e. R dq/dt = V0 − 2q/C

or, dq/(CV0 − 2q) = dt/(RC)

So, ln[(CV0 − 2q)/(CV0)] = −2t/(RC) for 0 ≤ t,

or, q = (CV0/2)(1 − e−2t/RC)

Hence I = i = dq/dt = (CV0/2)(2/RC) e−2t/RC = (V0/R) e−2t/RC

(b) Now, the heat liberated,

Q = ∫0∞ i2R dt = (V02/R2) R ∫0∞ e−4t/RC dt = ¼CV02

Teacher's Note: Two equal capacitors share charge through R: time constant RC/2, half the stored energy is lost as heat.

Exam Note: Quote I = (V0/R)e^(−2t/RC) and Q = CV0²/4.

Question 206. A coil of radius r = 25 cm wound of a thin copper wire of length l = 500 m rotates with an angular velocity ω = 300 rad/s about its axis. The coil is connected to a ballistic galvanometer by means of sliding contacts. The total resistance of the circuit is equal to R = 21 Ω. Find the specific charge of current carriers in copper if a sudden stoppage of the coil makes a charge q = 10 nC flow through the galvanometer.
Solution.

In a rotating frame, to first order in ω, the main effect is a Coriolis force 2m v′ × ω. This unbalanced force will cause electrons to react by setting up a magnetic field B so that the magnetic force e v × B balances the Coriolis force.

Thus −(e/2m) B = ω, or B = −(2m/e) ω.

The flux associated with this is Φ = Nπr2B = Nπr2(2m/e)ω, where N = l/(2πr) is the number of turns of the coil. If ω changes (and there is time for the electrons to rearrange) then B also changes and so does Φ. An emf will be induced and a current will flow. This gives

I = Nπr2(2m/e)(ω/R) (integrated over the stopping time)

The total charge flowing through the ballistic galvanometer, as the coil is stopped, is q = Nπr2(2m/e)ω/R.

So, e/m = 2Nπr2ω/(qR) = lωr/(qR) ≈ 1.8 × 1011 C/kg

Numerical value added by calculation: 500 × 300 × 0.25 / (10−8 × 21) = 1.79 × 1011 C/kg.

Teacher's Note: Electrons lag the rotating lattice (inertia); stopping the coil releases that charge, and q = ΔΦ/R gives e/m.

Exam Note: Use N = l/2πr; give e/m in C/kg.

Question 207. Find the total momentum of electrons in a straight wire of length l = 1000 m carrying a current I = 70 A.
Solution.

Let n0 be the total number of electrons; then the total momentum of electrons is p = n0mevd   (1)

Now, I = ρSxvd = (n0e/V)Sxvd = (n0e/l)vd   (2)

Here Sx = cross-sectional area, ρ = electron charge density, V = volume of the sample.

From (1) and (2): p = (me/e) I l = 0.40 μN·s

Teacher's Note: Total momentum = N·m·vd, and N·e·vd = I·l, so p = meIl/e.

Exam Note: Result is independent of wire material and area.

Question 208. A copper wire carries a current of density j = 1.0 A/mm2. Assuming that one free electron corresponds to each copper atom, evaluate the distance which will be covered by an electron during its displacement l = 10 mm along the wire.
Solution.

By definition nevd = j (where vd is the drift velocity, n is the number density of electrons).

Then the time taken is τ = l/vd = nel/j.

So the distance actually travelled is

s = ⟨v⟩τ = nel⟨v⟩/j

(⟨v⟩ = mean velocity of thermal motion of an electron)

Numerical estimate added by calculation (the book leaves it in symbols): with n = 8.5×1028 m−3 (copper) and ⟨v⟩ = √(8kT/πm) ≈ 1.1×105 m/s at 300 K, τ = nel/j ≈ 1.4×102 s and s ≈ 1.5×107 m, i.e. about 1.5×104 km.

Teacher's Note: Time to drift 10 mm is l/vd; in that time the electron moves randomly at thermal speed.

Exam Note: Distinguish drift speed from thermal speed.

Question 209. A straight copper wire of length l = 1000 m and cross-sectional area S = 1.0 mm2 carries a current I = 4.5 A. Assuming that one free electron corresponds to each copper atom, find:
(a) the time it takes an electron to displace from one end of the wire to the other;
(b) the sum of electric forces acting on all free electrons in the given wire.
Solution.

Let n be the volume density of electrons; then from I = ρSxvd,

I = neSx|⟨v⟩| = neSx(l/t)

So, t = neSxl/I = 3 Ms (about 35 days).

(b) Sum of electric forces = |(nV) e E| = |nSle ρ j|, where ρ is the resistivity of the material,

= nSleρ(I/S) = nelρI = 1.0 MN

Corrected: the printed answers read "3 μs" and "1.0 μN"; recalculation with n = 8.5×1028 m−3 and ρ = 1.7×10−8 Ω·m gives t = 3.0×106 s = 3 Ms and F = 1.0×106 N = 1.0 MN.

Teacher's Note: Drift speed is tiny (~0.3 mm/s) so crossing 1 km takes weeks; force = N·eE.

Exam Note: Check units: mega, not micro.

Question 210. A homogeneous proton beam accelerated by a potential difference V = 600 kV has a round cross-section of radius r = 5.0 mm. Find the electric field strength on the surface of the beam and the potential difference between the surface and the axis of the beam if the beam current is equal to I = 50 mA.
Solution.

(a) From Gauss's theorem, the field strength at the surface of a cylindrical shape equals E = λ/(2πε0r), where λ is the linear charge density.

Now, eV = ½mv2, or v = √(2eV/m)   (1), where m is the mass of a proton.

Also, dq = λdx, so dq/dt = λ dx/dt, i.e. I = λv, or λ = I/v = I/√(2eV/m), using (1).

Hence E = [I/(2πε0r)] √(m/(2eV)) ≈ 17 kV/m

(b) For a point inside the solid charged cylinder (uniform charge density), applying Gauss' theorem,

2πrhE = πr2h · q/(ε0πR2l), or E = (q/l) r/(2πε0R2) = λr/(2πε0R2)

So, from E = −dφ/dr:

∫φ2φ1 (−dφ) = ∫0R [λ/(2πε0R2)] r dr, or

φ1 − φ2 = [λ/(2πε0R2)] [r2/2]0R = λ/(4πε0)

Hence φ1 − φ2 = [I/(4πε0)] √(m/(2eV)) ≈ 42 V

Corrected: the printed numerical answers (32 V/m and 0.80 V) do not follow from the formulas for a proton beam, and the printed potential formula carries a stray factor V. Using the proton mass m = 1.67×10−27 kg: v = 1.07×107 m/s, λ = 4.7×10−9 C/m, E ≈ 1.7×104 V/m, φ1 − φ2 ≈ 42 V.

Teacher's Note: Beam acts as a uniformly charged cylinder: λ = I/v from the accelerating voltage; inside, field grows linearly.

Exam Note: Use proton mass, not electron mass.

Question 211. Two large parallel plates are located in vacuum. One of them serves as a cathode, a source of electrons whose initial velocity is negligible. An electron flow directed toward the opposite plate produces a space charge causing the potential in the gap between the plates to vary as φ = ax4/3, where a is a positive constant, and x is the distance from the cathode. Find:
(a) the volume density of the space charge as a function of x;
(b) the current density.
Solution.

Between the plates φ = ax4/3. Or, ∂φ/∂x = a × (4/3) x1/3.

Or, d2φ/dx2 = (4/9) a x−2/3 = −ρ/ε0.

Or, ρ = −(4ε0a/9) x−2/3

Let the charge on the electron be −e. Then ½mv2 − eφ = const = 0, as the electron is initially emitted with negligible energy.

v2 = 2eφ/m, v = √(2eφ/m) = √(2ea/m) x2/3

So, j = −ρv = (4ε0a/9) √(2eφ/m) x−2/3 = (4ε0a/9) √(2ea/m), independent of x.

(j is measured from the anode to the cathode, so the − sign is taken.)

Teacher's Note: Poisson gives ρ from φ″; energy conservation gives v, and ρv comes out constant in x.

Exam Note: Constant j confirms steady flow; mind the sign.

Question 212. The air between two parallel plates separated by a distance d = 20 mm is ionized by X-ray radiation. Each plate has an area S = 500 cm2. Find the concentration of positive ions if at a voltage V = 100 V a current I = 3.0 μA flows between the plates, which is well below the saturation current. The air ion mobilities are u0+ = 1.37 cm2/(V·s) and u0− = 1.91 cm2/(V·s).
Solution.

E = V/d. So by the definition of mobility v+ = u0+V/d, v− = u0−V/d.

And j = (n+u0+ + n−u0−) eV/d

(The negative ions move towards the anode and the positive ions towards the cathode and the total current is the sum of the currents due to them.) On the other hand, in equilibrium n+ = n−.

So, n+ = n− = (I/S)/[(u0+ + u0−) eV/d]

= Id/[eVS(u0+ + u0−)] = 2.3 × 108 cm−3

Teacher's Note: Current density is the sum of positive and negative ion fluxes; n+ = n− in a neutral ionised gas.

Exam Note: Keep cm units consistently: u in cm²/(V·s).

Question 213. A gas is ionized in the immediate vicinity of the surface of plane electrode 1 (Fig. 3.58) separated from electrode 2 by a distance l. An alternating voltage varying with time t as V = V0 sin ωt is applied to the electrodes. On decreasing the frequency ω it was observed that the galvanometer G indicates a current only at ω < ω0, where ω0 is a certain cut-off frequency. Find the mobility of ions reaching electrode 2 under these conditions.
G12lV = V₀ sin ωt

Fig. 3.58 (schematic): plane electrodes 1 and 2, distance l apart; electrode 2 is connected to a galvanometer G, and the alternating voltage V is applied between the electrodes.

Solution.

Velocity = mobility × field, or v = u (V0/l) sin ωt, which is positive for 0 ≤ ωt ≤ π.

So, the maximum displacement in one direction is

xmax = ∫0π/ω u (V0/l) sin ωt dt = 2uV0/(lω)

At ω = ω0, xmax = l, so 2uV0/(lω0) = l.

Thus u = ω0l2/(2V0)

Teacher's Note: Ions reach electrode 2 only if their one-half-cycle drift 2uV₀/(lω) is at least l; cut-off sets equality.

Exam Note: Use ω = ω₀ at the cut-off, not general ω.

Question 214. The air between two closely located plates is uniformly ionized by ultraviolet radiation. The air volume between the plates is equal to V = 500 cm3, the observed saturation current is equal to Isat = 0.48 μA. Find:
(a) the number of ion pairs produced in a unit volume per unit time;
(b) the equilibrium concentration of ion pairs if the recombination coefficient for air ions is equal to r = 1.67 × 10−6 cm3/s.
Solution.

(a) When the current is saturated, all the ions produced reach the plates. Then

ṅi = Isat/(eV) = 6 × 109 cm−3s−1

(Both positive ions and negative ions are counted here, i.e. ion pairs.)

(b) The equation of balance is dn/dt = ṅi − rn2.

The first term on the right is the production rate and the second term is the recombination rate, which by the usual statistical arguments is proportional to n2 (= number of positive ions × number of negative ions). In equilibrium dn/dt = 0, so

neq = √(ṅi/r) = 6 × 107 cm−3

Teacher's Note: Saturation means every pair produced is collected; equilibrium balances production against recombination rn².

Exam Note: Equilibrium uses dn/dt = 0, giving a square root.

Question 215. Having been operated long enough, the ionizer producing ṅi = 3.5 × 109 cm−3·s−1 of ion pairs per unit volume of air per unit time was switched off. Assuming that the only process tending to reduce the number of ions in air is their recombination with coefficient r = 1.67 × 10−6 cm3/s, find how soon after the ionizer's switching off the ion concentration decreases η = 2.0 times.
Solution.

Initially n = n0 = √(ṅi/r), since we can assume that the long exposure to the ionizer has caused equilibrium to be set up. After the ionizer is switched off,

dn/dt = −rn2, or r dt = −dn/n2, or rt = 1/n + constant.

But n = n0 at t = 0, so rt = 1/n − 1/n0.

The concentration will decrease by a factor η when

rt0 = 1/(n0/η) − 1/n0 = (η − 1)/n0

or, t0 = (η − 1)/√(rṅi) = 13 ms

Teacher's Note: Pure recombination gives 1/n growing linearly in time; start from the equilibrium n0.

Exam Note: Substitute η = 2 last; answer in ms.

Question 216. A parallel-plate air capacitor whose plates are separated by a distance d = 5.0 mm is first charged to a potential difference V = 90 V and then disconnected from a d.c. voltage source. Find the time interval during which the voltage across the capacitor decreases by η = 1.0%, taking into account that the average number of ion pairs formed in air under standard conditions per unit volume per unit time is equal to ṅi = 5.0 cm−3·s−1 and that the given voltage corresponds to the saturation current.
Solution.

Ions produced will cause the charge to decay. Clearly,

ηCV = decrease of charge = ṅieA d t = (ε0A/d) V η, i.e. ṅieAd·t = (ε0A/d)Vη

Or, t = ε0Vη/(ṅied2) = 4.6 days

Note that ṅi here is the number of ion pairs produced per unit volume per unit time.

Teacher's Note: Saturated ionisation current ṅieAd drains charge ηCV; equate and solve for time.

Exam Note: Convert ṅi to SI (m⁻³s⁻¹); result 4.6 days.

Question 217. The gap between two plane plates of a capacitor equal to d is filled with a gas. One of the plates emits ν0 electrons per second which, moving in an electric field, ionize gas molecules; this way each electron produces α new electrons (and ions) along a unit length of its path. Find the electronic current at the opposite plate, neglecting the ionization of gas molecules by formed ions.
Solution.

If ν = the number of electrons per second moving to the anode at distance x, then dν/dx = αν, or ν = ν0eαx.

Assuming saturation, I = eν0eαd

Teacher's Note: Each electron multiplies along the path: dν/dx = αν gives exponential avalanche growth.

Exam Note: Evaluate at x = d for the anode current.

Question 218. The gas between the capacitor plates separated by a distance d is uniformly ionized by ultraviolet radiation so that ṅi electrons per unit volume per second are formed. These electrons moving in the electric field of the capacitor ionize gas molecules, each electron producing α new electrons (and ions) per unit length of its path. Neglecting the ionization by ions, find the electronic current density at the plate possessing a higher potential.
Solution.

Since the electrons are produced uniformly through the volume, the total current attaining saturation is clearly

I = ∫0d e(ṅiA dx) eαx = eṅiA (eαd − 1)/α

Thus, j = I/A = eṅi (eαd − 1)/α

Teacher's Note: Electrons born at depth x then multiply by eα(d−x) to the anode; integrate over the gap.

Exam Note: Integrate the source over the gap; limit α→0 gives eṅid.

IE Irodov Solutions for JEE Mathematics: IE Irodov Solutions Chapter 19 Electric Current Part 2

Complete Math Solutions for IE Irodov Solutions Chapter 19 Electric Current Part 2

Access the complete chapter-wise PDF for IE Irodov Solutions Chapter 19 Electric Current Part 2. These structured IE Irodov Solutions solutions for JEE Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.

Concept-Driven Math Answers

Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.

Next Steps in Your Mathematics Revision

Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.

FAQs

What are these IE Irodov Solutions for JEE Physics?

They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.

Are the IE Irodov JEE Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these IE Irodov solutions for JEE Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising IE Irodov JEE Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these JEE Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.