Step-by-Step P Bahadur Solutions for JEE Chemistry Chapter 14 Conductance Of A Solution
Access comprehensive textbook solutions for Chapter 14 Conductance Of A Solution using the P Bahadur reference material for JEE Chemistry. Designed to align with the 2026 academic curriculum, these detailed answers help students reinforce core academic concepts and master complex problem-solving methods.
Download Chapter 14 Conductance Of A Solution Textbook Solutions PDF
Navigate directly to the solved Chemistry textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Chapter 14 Conductance of a Solution - Numerical, Objective and Previous Years Problems (pages 1-16)
Numerical Problems
Question 1. The resistance of a 0.01 N solution of an electrolyte was found to be 210 ohm at 298 K using a conductivity cell with a cell constant of 0.88 cm-1. Calculate conductivity and equivalent conductivity of solution.
Solution.
Given: R = 210 ohm, l/a = 0.88 cm-1, N = 0.01.
κ = (1/R)(l/a) = 0.88/210 = 4.19 × 10-3 mho cm-1 (S cm-1).
Λeq = κ × 1000/N = 4.19 × 10-3 × 1000/0.01 = 419.05 S cm2 eq.-1.
Teacher's Note: Conductivity needs the cell constant: κ = cell constant / R. Then Λ = κ × 1000 / normality.
Exam Note: Show κ first; units S cm-1 then S cm2 eq.-1.
Question 2. The conductivity of N/50 solution of a cell of KCl at 25°C is 0.002765 S cm-1. If the resistance of a cell containing this solution is 400 ohm, find out cell constant.
Solution.
κ = (1/R) × (l/a), so 0.002765 = (1/400) × cell constant.
Cell constant = 0.002765 × 400 = 1.106 cm-1.
Teacher's Note: Cell constant l/a = κ × R; it is fixed for a given cell and found using standard KCl.
Exam Note: State unit cm-1; formula l/a = κR earns the mark.
Question 3. The resistance of a decinormal solution of a salt occupying a volume between two platinum electrodes 1.80 cm apart and 5.4 cm2 in area was found to be 32 ohm. Calculate the conductivity and equivalent conductivity of solution.
Solution.
κ = (1/R)(l/a) = (1/32) × (1.80/5.4) = 0.01042 S cm-1 (the book prints 0.01041).
Λeq = κ × 1000/N = 0.01042 × 1000/0.1 = 104.2 S cm2 eq.-1 (the book prints 104.1, a truncation of the same value).
Teacher's Note: Decinormal means N = 0.1. Geometry gives l/a = 1.80/5.4 = 1/3 cm-1.
Exam Note: Decinormal = 0.1 N; do not use 1 N by mistake.
Question 4. When a certain conductance cell was filled with 0.02 M KCl solution (conductivity 0.002768 S cm-1), it had a resistance of 82.4 ohm at 298 K. When filled with 0.005 N K2SO4, it had a resistance of 324 ohm. Calculate: (a) cell constant, (b) conductance of 0.005 N K2SO4 solution, (c) conductivity of 0.005 N K2SO4 solution, (d) equivalent conductivity of 0.005 N K2SO4 solution, (e) molecular conductivity of 0.005 N K2SO4.
Solution.
(a) From the KCl data, l/a = κ × R = 0.002768 × 82.4 = 0.2281 cm-1.
(b) C = 1/R = 1/324 = 3.086 × 10-3 S.
(c) κ = C × (l/a) = 3.086 × 10-3 × 0.2281 = 7.04 × 10-4 S cm-1.
(d) Λeq = κ × 1000/N = 7.04 × 10-4 × 1000/0.005 = 140.80 S cm2 eq.-1.
(e) K2SO4 is bivalent, so M = N/2 = 0.0025. ΛM = κ × 1000/M = 7.04 × 10-4 × 1000/0.0025 = 281.6 S cm2 mol-1.
Teacher's Note: Standard KCl calibrates the cell; molar conductivity of K2SO4 is twice its equivalent value because M = N/2.
Exam Note: Do (a) first; all later parts depend on it.
Question 5. At 18°C, the velocity of migration of Ag+ ion is 0.00057 cm sec-1 and that of NO3- is 0.00063 cm sec-1 at infinite dilution. What is the equivalent conductivity of AgNO3 at infinite dilution?
Solution.
λ°cation = u°cation × Faraday = 0.00057 × 96500, so λ°Ag+ = 55.005 S cm2 eq.-1.
λ°anion = u°anion × Faraday = 0.00063 × 96500, so λ°NO3- = 60.795 S cm2 eq.-1.
By Kohlrausch law, Λ°AgNO3 = 55.005 + 60.795 = 115.8 S cm2 eq.-1.
Teacher's Note: Ionic conductance = mobility × F; the given speeds are per unit potential gradient. Add ions by Kohlrausch law.
Exam Note: Use F = 96500 C; add cation and anion values.
Question 6. The molar conductivity of acetic acid at infinite dilution is 390.7 and for 0.1 M acetic acid solution is 5.2 S cm2 mol-1. Calculate the (1) degree of dissociation of acetic acid, (2) [H+] in solution.
Solution.
(1) α = Λv/Λ° = 5.2/390.7 = 0.0133, i.e. 1.33%.
(2) CH3COOH ⇌ CH3COO- + H+: initially 1, 0, 0; after dissociation (1 - α), α, α.
[H+] = Cα = 0.1 × 0.0133 = 0.00133 M.
Teacher's Note: For a weak electrolyte α = Λv/Λ°; then [H+] = Cα.
Exam Note: Write α formula, then [H+] = Cα with units.
Question 7. 0.04 N solution of a weak acid has a conductivity 4.23 × 10-4 S cm-1. The degree of dissociation of acid at this dilution is 0.0612. Calculate the equivalent conductivity of weak acid at infinite dilution.
Solution.
Λeq = κ × 1000/N = 4.23 × 10-4 × 1000/0.04 = 10.575 S cm2 eq.-1.
α = Λeq/Λ°eq, so 0.0612 = 10.575/Λ°eq.
Λ°eq = 172.79 S cm2 eq.-1.
Teacher's Note: First get Λ at the given concentration from κ, then extrapolate using α = Λ/Λ°.
Exam Note: Compute Λ first, then Λ° = Λ/α.
Question 8. The equivalent conductivity of 0.05 N solution of a monobasic acid is 15.8 S cm2 eq.-1. If equivalent conductivity of the acid at infinite dilution is 350 S cm2 eq.-1, calculate the (1) degree of dissociation of acid, (2) dissociation constant of acid.
Solution.
(1) α = Λeq/Λ°eq = 15.8/350 = 0.04514.
(2) For HA ⇌ H+ + A-: K = Cα2/(1 - α) ≈ Cα2 = 0.05 × (0.04514)2 = 1.019 × 10-4.
Note: since α = 0.04514, 1 - α ≈ 1 is assumed. C is in mol litre-1; HA is monobasic, so normality = molarity.
Teacher's Note: Ostwald dilution law with 1 - α ≈ 1 when α is small. Monobasic acid: N = M.
Exam Note: State the approximation 1 - α ≈ 1 for K.
Question 9. The resistance of a solution 'A' is 50 ohm and that of solution 'B' is 100 ohm, both solutions being taken in the same conductivity cell. If equal volumes of solutions A and B are mixed, what will be the resistance of the mixture using the same cell? (Assume that there is no increase in the degree of dissociation of A and B on mixing.)
Solution.
Let κ1 and κ2 be the conductivities of A and B and x the cell constant.
κ1 = (1/50) × x ...(1); κ2 = (1/100) × x ...(2).
On mixing equal volumes each solution is diluted to double its volume, so the contributions are κ1/2 and κ2/2 and the conductivity of the mixture is (1/2)(κ1 + κ2) = (1/R) × x ...(3), where R is the resistance of the mixture.
From (1), (2) and (3): R = 66.67 ohm.
Teacher's Note: Equal volumes halve each concentration, so conductivities add and are halved: κ = (κ1 + κ2)/2.
Exam Note: Do not average resistances; average conductivities.
Question 10. A big irregular shaped vessel contained water, the conductivity of which was 2.56 × 10-5 S cm-1. 500 g of NaCl was then added to the water and the conductivity after the addition of NaCl was found to be 3.10 × 10-5 S cm-1. Find the capacity of the vessel if it is fulfilled with water (Λ°M of NaCl = 149.9).
Solution.
Let the volume of the vessel be V litre. Equivalents of NaCl = 500/58.5 = 8.547, so N = 8.547/V.
Conductivity due only to Na+ and Cl-: κv = 3.10 × 10-5 - 2.56 × 10-5 = 0.54 × 10-5 S cm-1.
ΛM NaCl = 0.54 × 10-5 × 1000V/8.547. Since the vessel is big, the resulting solution may be supposed to be dilute, so ΛM NaCl = Λ°M NaCl.
0.54 × 10-5 × 1000V/8.547 = 149.9, so V = 2.3725 × 105 litre (the book writes 2372.5 × 102), i.e. V ≈ 2.37 × 105 litre.
Teacher's Note: Subtract water conductivity first; the huge volume means dilute, so Λ ≈ Λ°.
Exam Note: Subtract solvent conductivity before using κ.
Question 11. The equivalent conductivity of 0.1 N solution of MgCl2 is 97.1 S cm2 eq.-1 at 25°C. A cell with electrodes that are 1.50 cm2 in surface area and 0.50 cm apart is filled with 0.1 N MgCl2 solution. How much current will flow when the potential difference between the electrodes is 5 volts?
Solution.
Cell constant = 0.50/1.50 = 1/3 cm-1.
Conductivity = (equivalent conductivity) × N/1000 = 97.1 × 0.1/1000 = 0.00971 S cm-1.
Conductance = κ/(cell constant) = 0.00971/(1/3) = 0.02913 S, so resistance = 1/0.02913 ohm.
Current = V/R = 5/(1/0.02913) = 0.1456 ampere.
Teacher's Note: Chain: Λ gives κ, cell constant gives conductance, then Ohm's law gives current.
Exam Note: Convert Λ to κ, then use I = V × conductance.
Question 12. At 18°C the conductivities of H+ and CH3COO- at infinite dilution are 315 and 35 S cm2 eq.-1 respectively. The conductivity of 0.001 N solution of acetic acid is 4.1 × 10-5 S cm-1 at the same temperature. What is the degree of dissociation of acetic acid?
Solution.
Λ°eq CH3COOH = λ°H+ + λ°CH3COO- = 315 + 35 = 350 S cm2 eq.-1.
Λeq = κ × 1000/N = 4.1 × 10-5 × 1000/0.001 = 41 S cm2 eq.-1.
α = Λeq/Λ°eq = 41/350 = 0.117, i.e. 11.7%.
Teacher's Note: Kohlrausch gives Λ° from ion values; measured κ gives Λ; their ratio is α.
Exam Note: Convert κ to Λ with 1000/N before dividing.
Question 13. The equivalent conductivity of acetic acid at infinite dilution is 387 S cm2 eq.-1. At the same temperature, 0.001 M solution of acetic acid, it is 55 S cm2 eq.-1. What is the degree of dissociation of 0.1 N acetic acid? Assume 1 - α ≈ 1.
Solution.
For 0.001 M CH3COOH: α = Λeq/Λ°eq = 55/387 = 0.142 (14.2%).
Ka = Cα2/(1 - α) = 0.001 × (0.142)2/(1 - 0.142) = 2.35 × 10-5.
Now for 0.1 N: Ka = Cα2/(1 - α) = 0.1 × α2/(1 - α) = 2.35 × 10-5; with 1 - α ≈ 1, αat 0.1 = 0.015 or 1.5%.
Teacher's Note: Ka is constant at fixed temperature: get it from the dilute data, then reuse it.
Exam Note: Use Ka from first case; α = √(Ka/C).
Question 14. Ionic conductivity at infinite dilution of Al3+ and SO42- ions are 189 S cm2 eq.-1 and 160 S cm2 eq.-1 respectively. Calculate the equivalent and molar conductivity of Al2(SO4)3 at infinite dilution.
Solution.
Λ°eq Al2(SO4)3 = (1/n+)λ°Al3+ + (1/n-)λ°SO42- = (1/3) × 189 + (1/2) × 160 = 143 S cm2 eq.-1.
Λ°M Al2(SO4)3 = 6 × Λ°eq = 6 × 143 = 858 S cm2 mol-1.
Check: Λ°M = γ+λ°Al3+ + γ-λ°SO42- = 2 × 189 + 3 × 160 = 858 S cm2 mol-1.
Note: the book treats 189 and 160 as the conductances per mole of ion (that is why they are divided by the charge); the unit "eq.-1" in the statement should read "mol-1".
Teacher's Note: Equivalent value divides each ionic conductance by its charge; molar value uses stoichiometric numbers 2 and 3.
Exam Note: Al2(SO4)3 has 6 equivalents per mole: ΛM = 6Λeq.
Question 15. The equivalent conductivity of CH3COONa, HCl and NaCl at infinite dilution are 91.6, 425.0 and 128.1 S cm2 eq.-1 respectively. Calculate equivalent conductivity of acetic acid at infinite dilution. Also if degree of dissociation of 0.1 N acetic acid is 0.001, find the equivalent conductivity at this dilution and concentration of acetic acid.
Solution.
By Kohlrausch law Λ°eq CH3COOH = λ°CH3COO- + λ°H+.
Λ°CH3COONa = 91.6 = λ°CH3COO- + λ°Na+ ...(1); Λ°HCl = 425.0 = λ°H+ + λ°Cl- ...(2); Λ°NaCl = 128.1 = λ°Na+ + λ°Cl- ...(3).
(1) + (2) - (3): Λ°CH3COOH = 91.6 + 425.0 - 128.1 = 388.5 S cm2 eq.-1.
α = Λeq/Λ°eq: 0.001 = Λeq/388.5, so Λeq = 0.3885 S cm2 eq.-1.
Teacher's Note: Add the two sodium-free combinations and subtract NaCl so Na+ and Cl- cancel.
Exam Note: Show the three equations and the cancellation of Na+ and Cl-.
Question 16. Calculate molar conductivity for NH4OH, given that molar conductivity for Ba(OH)2, BaCl2 and NH4Cl are 523.28, 280.0 and 129.8 S cm2 mol-1 respectively.
Solution.
Λ°M Ba(OH)2 = λ°Ba2+ + 2λ°OH- = 523.28 ...(1)
Λ°M BaCl2 = λ°Ba2+ + 2λ°Cl- = 280.00 ...(2)
Λ°M NH4Cl = λ°NH4+ + λ°Cl- = 129.80 ...(3)
Multiply (3) by 2 and subtract from (2): λ°Ba2+ - 2λ°NH4+ = 280 - 2 × 129.8 = 20.40 ...(4).
Subtract (4) from (1): 2λ°NH4+ + 2λ°OH- = 502.88.
Therefore λ°NH4+ + λ°OH- = Λ°M NH4OH = 502.88/2 = 251.44 S cm2 mol-1.
Teacher's Note: Eliminate Ba2+ and Cl- by combining (1) - (2) + 2 × (3), then halve.
Exam Note: Equation combination: [Ba(OH)2 - BaCl2 + 2NH4Cl]/2.
Question 17. Calculate the dissociation constant of H2O at 25°C from the following data: Conductivity of H2O = 5.8 × 10-8 S cm-1, λ°H+ = 350.0 and λ°OH- = 198.0 S cm2 eq.-1.
Solution.
Suppose water contains N mol/litre (N eq./litre) of H+ or OH- ions. Equivalents of H+ = equivalents of H2O in solution, so the equivalent conductivity of water = κ × 1000/N = 5.8 × 10-8 × 1000/N.
Water dissociates feebly, so it is a dilute solution of H+ and OH- and Λeq H2O = Λ°eq H2O = λ°H+ + λ°OH- = 350 + 198 = 548.
5.8 × 10-8 × 1000/N = 548, so N = 1.058 × 10-7, i.e. [H+] = [OH-] = 1.058 × 10-7.
For H2O ⇌ H+ + OH-: K = [H+][OH-]/[H2O], so Kw = K × [H2O] = [H+][OH-] = 1.119 × 10-14.
K = Kw/[H2O] = 1.119 × 10-14/55.5 = 2 × 10-16 mol litre-1 (where [H2O] = 1000/18 = 55.5 mol/litre).
Alternate solution: taking the molarity of water as 55.6 mol litre-1 and Λ°eq H2O = 350.0 + 198.0 = 548, Λ/Λ° = 5.8 × 10-8 × 1000/(55.6 × 548) = 1.9 × 10-9. Then K = Cα2/(1 - α) ≈ Cα2 = 55.6 × (1.9 × 10-9)2 = 2.0 × 10-16 mol litre-1.
Teacher's Note: Pure water is extremely dilute, so Λ ≈ Λ° = λ(H+) + λ(OH-); K = Kw/55.5.
Exam Note: Do not confuse K (2 × 10-16) with Kw (10-14).
Question 18. The equivalent conductivity of KCl at infinite dilution is 130 S cm2 eq.-1. The transport no. of Cl- ion in KCl at the same temperature is 0.505. What is the limiting ionic mobility and ionic conductance of K+ ion?
Solution.
tCl- = 0.505 and tK+ + tCl- = 1, so tK+ = 1 - 0.505 = 0.495.
Ionic conductance λ°K+ = Λ°KCl × tK+ = 130 × 0.495 = 64.35 S cm2 eq.-1.
λ°K+ = u°K+ × F, so limiting ionic mobility u°K+ = 64.35/96500 = 6.67 × 10-4 cm2 sec-1 volt-1.
Teacher's Note: Transport numbers add to 1; ionic conductance = t × Λ°; mobility = λ°/F.
Exam Note: Units of mobility: cm2 V-1 s-1.
Question 19. At a certain temperature, the saturated solution of silver chloride has conductivity 1.12 × 10-6 S cm-1. The ionic conductances of Ag+ and Cl- ions at infinite dilution are 54.3 and 65.5 S cm2 eq.-1 at same temperature. Find the solubility of AgCl in g litre-1 at this temperature.
Solution.
Λ°eq AgCl = λ°Ag+ + λ°Cl- = 54.3 + 65.5 = 119.8 S cm2 eq.-1.
For a sparingly soluble salt Λeq = Λ°eq, and Λeq = κ × 1000/N, so 119.8 = 1.12 × 10-6 × 1000/N.
N = 1.12 × 10-3/119.8 eq./litre = 9.35 × 10-6 eq./litre.
S = (1.12 × 10-3/119.8) × 143.5 g/litre = 1.34 × 10-3 g/litre.
Note: in the case of sparingly soluble salts ΛM = Λ°M, since solubility is very low and the electrolyte is assumed to be 100% ionised at normal conditions.
Teacher's Note: Sparingly soluble salt: solution so dilute that Λ = Λ°; then N = 1000κ/Λ°, solubility = N × molar mass.
Exam Note: Multiply by 143.5 g mol-1 for g/litre; AgCl is univalent.
Question 20. The conductivity of a saturated aqueous solution of Co2[Fe(CN)6] is 2.06 × 10-6 S cm-1. The conductivity of water used to prepare the solution has conductivity 4.1 × 10-7 S cm-1. If ionic molar conductivities of Co2+ and [Fe(CN)6]4- are 86 S cm2 mol-1 and 444.0 S cm2 mol-1 respectively. Calculate the solubility product of Co2[Fe(CN)6].
Solution.
The saturated solution is assumed to be 100% ionised, i.e. the condition at infinite dilution. For Co2[Fe(CN)6]: Λ°M = 2λ°Co2+ + λ°Fe(CN)64- = 2 × 86 + 444 = 616 S cm2 mol-1.
κcomplex = κsol - κH2O = 2.06 × 10-6 - 0.41 × 10-6 = 1.65 × 10-6 S cm-1.
If CM is the molarity: Λ°M = κ × 1000/CM, so 616 = 1.65 × 10-6 × 1000/CM and CM = 2.68 × 10-6 mol/litre.
Co2[Fe(CN)6] ⇌ 2Co2+ + [Fe(CN)6]4- (concentrations 2s and s), so Ksp = 4s3 = 4 × (2.68 × 10-6)3 = 7.699 × 10-17 (about 7.7 × 10-17).
Teacher's Note: Subtract water's conductivity, use Λ° (very dilute), find s; Ksp = (2s)2(s) = 4s3.
Exam Note: Stoichiometry 2:1 gives 4s3; subtract solvent κ first.
Question 21. Explain the conducting power order of the following ions: Li+(aq.) < Na+(aq.) < K+(aq.) < Rb+(aq.) < Cs+(aq.)
Solution.
The size of ions is Li+ < Na+ < K+ < Rb+, thus the smallest ion should move most rapidly. However ionic mobility shows the reverse trend because smaller ions are more easily hydrated and thus hydrated ion size for these ions is Li+(aq.) > Na+(aq.) > K+(aq.) > Rb+(aq.) > Cs+(aq.). Thus ionic mobility of Li+(aq.) is minimum.
Teacher's Note: Conductance depends on hydrated size: smaller bare ion, stronger hydration, larger hydrated ion, lower mobility.
Exam Note: Say "hydrated size", not crystal size, to earn the mark.
Question 22. A dilute solution of KCl was placed between two Pt electrodes 10.0 cm apart, across which a potential difference of 6.0 volt was applied. How far would K+ ions move in 2 hours at 25°C? Ionic conductance of K+ at infinite dilution is 73.52 S cm2 eq.-1 at 25°C.
Solution.
λ°K+ = 73.52. Ionic mobility u°K+ = λ°/F = 73.52/96500 = 7.619 × 10-4 cm2 sec-1 volt-1.
Potential gradient applied = 6.0/10 = 0.6 volt cm-1.
Speed of K+ = ionic mobility × potential gradient = 7.619 × 10-4 × 0.6 = 45.714 × 10-5 cm sec-1.
Distance travelled by K+ in 2 hours = 45.714 × 10-5 × 2 × 60 × 60 = 3.292 cm.
Teacher's Note: Mobility = λ°/F; speed = mobility × (V/l); distance = speed × time in seconds.
Exam Note: Convert 2 hours to 7200 s; use gradient V/l.
Question 23. The molar conductivities at infinite dilution of AgNO3, NaCl and NaNO3 are 116.5, 110.3 and 105.2 S cm2 mol-1 respectively. The conductivity of AgCl in water is 2.40 × 10-6 S cm-1 and of water used is 1.16 × 10-6 S cm-1. Find the solubility of AgCl in g litre-1.
Solution.
For monovalent electrolytes equivalent conductance = molar conductance. Λ°M AgNO3 = 116.5 = λ°Ag+ + λ°NO3- ...(1); Λ°M NaCl = 110.3 = λ°Na+ + λ°Cl- ...(2); Λ°M NaNO3 = 105.2 = λ°Na+ + λ°NO3- ...(3).
Λ°M AgCl = (1) + (2) - (3) = 116.5 + 110.3 - 105.2 = 121.6 S cm2 mol-1. For a sparingly soluble salt ΛM = Λ°M.
κAgCl = (2.40 - 1.16) × 10-6 = 1.24 × 10-6 S cm-1.
ΛM = κ × 1000/M: 121.6 = 1.24 × 10-6 × 1000/M, so M = 1.24 × 10-3/121.6 mol/litre.
Solubility = (1.24 × 10-3/121.6) × 143.5 = 1.463 × 10-3 g litre-1.
Teacher's Note: Get Λ° of AgCl by Kohlrausch combination, subtract water's κ, then solubility = 1000κ/Λ° × molar mass.
Exam Note: Subtract water conductivity; combine AgNO3 + NaCl - NaNO3.
Question 24. A water sample of swimming pool shows the resistance of 9.2 × 103 ohm at 25°C using a conductivity cell. The same cell dipped in 0.02 M KCl has the resistance of 85 ohm. Now 0.5 kg sodium chloride is dissolved in pool and thoroughly stirred. The solution sample now shows the resistance of 7.6 × 103 ohm. If Λ°M for NaCl and Λv for 0.02 M KCl are 126.5 S cm2 mol-1 and 138.0 S cm2 mol-1, calculate the volume of water in pool.
Solution.
For 0.02 M KCl: ΛM = κ × 1000/M, so 138 = κ × 1000/0.02 and κ = 2.76 × 10-3 S cm-1.
κ = (1/R)(l/a): 2.76 × 10-3 = (1/85) × (l/a), so the cell constant l/a = 0.2346 cm-1.
Conductance of pool water Cpool water = 1/(9.2 × 103) = 1.087 × 10-4 S. (Note: conductivity is an additive property but resistance is not.)
CNaCl(aq.) = 1/(7.6 × 103) = 1.316 × 10-4 S, so CNaCl = CNaCl(aq.) - Cpool water = (1.316 - 1.087) × 10-4 = 2.29 × 10-5 S.
κNaCl = C × l/a = 2.29 × 10-5 × 0.2346 = 5.37 × 10-6 S cm-1.
Λ°M = κ × 1000/M, where M = (500/58.5)/V(l) = 8.55/Vl (V is the volume of water ≈ volume of solution): 126.5 = 5.37 × 10-6 × 1000 × V(l)/8.55.
Hence V(l) = 2.01 × 105 litre.
Teacher's Note: KCl standard gives the cell constant; subtract pool-water conductance from the salted-water conductance.
Exam Note: Subtract conductances, never resistances.
Question 25. At 298 K, the conductivity of pure water is 5.51 × 10-8 S cm-1. The ionic conductances of H+ and OH- at this temperature are 349.8 and 198.5 S cm2 eq.-1 respectively. Calculate the ionic product of water.
Solution.
Λ°eq H2O = λ°H+ + λ°OH- = 349.8 + 198.5 = 548.3 S cm2 eq.-1. For water Λeq = Λ°eq.
Λeq = κ × 1000/N: 548.3 = 5.51 × 10-8 × 1000/N, so N = 1.005 × 10-7 eq. litre-1.
[H+] = [OH-] = 1.005 × 10-7, so Kw = [H+][OH-] = (1.005 × 10-7)2 = 1.01 × 10-14.
Teacher's Note: Pure water is ultra-dilute, so Λ ≈ Λ°; N = 1000κ/Λ° gives [H+].
Exam Note: Square [H+] to get Kw.
Question 26. A decinormal solution of AgNO3 was electrolysed between Pt electrodes. After passing a small current for two hour, a fall of concentration of 0.0005124 equivalent occurred in anodic solution. The mass of copper deposited in copper coulometer placed in series was found to be 0.03879 g. Find the transport no. of Ag+ and NO3- in AgNO3.
Solution.
Fall of concentration around anode = 0.0005124 eq. Mass of copper deposited in coulometer = 0.03879 g, so equivalents of copper = 0.03879/31.8 = 0.001219 eq.
For Pt electrodes, tAg+ = (equivalents of Ag+ lost in anode)/(equivalents of Cu deposited in coulometer) = 0.0005124/0.001219 = 0.4201.
Corrected: the book prints tAg+ = 0.4303, but 0.0005124/0.001219 = 0.4201 (checked).
tNO3- = 1 - 0.4201 = 0.5799 (the book prints 0.5697 as a consequence of its wrong arithmetic).
Teacher's Note: Hittorf with inert electrodes: t(cation) = fall in anode concentration / total charge passed (copper coulometer).
Exam Note: Check the division; t+ + t- = 1.
Question 27. A solution of AgNO3 was electrolysed between silver electrodes. Before electrolysis, 10 g of solution contained 0.01788 g of AgNO3. After the experiment, 20.09 g of the anodic solution contained 0.06227 g of AgNO3. At the same time, 0.009479 g of Cu was deposited in copper coulometer placed in series. Calculate transport no. of Ag+ and NO3-.
Solution.
After electrolysis: 20.09 g of anodic solution contained 0.06227 g AgNO3, so water = 20.09 - 0.06227 = 20.02773 g. 0.06227 g AgNO3 = 0.06227/170 = 0.0003664 equivalent of Ag+.
Before electrolysis: 10 g solution contained 0.01788 g AgNO3, so water = 10 - 0.01788 = 9.98212 g. The same 20.02773 g of water has 0.01788 × 20.02773/(170 × 9.98212) = 0.0002111 equivalent of Ag+.
Apparent increase in Ag+ around anode = 0.0003664 - 0.0002111 = 0.0001553 eq.
Cu deposited in coulometer = 0.009479/31.8 = 0.0002982 eq. This is also the actual increase around the anode (equal equivalents are discharged at either electrode, Ag dissolving from the anode).
Ag+ has migrated away from the anode, which brings a fall in concentration, so the fall = actual increase - apparent increase = 0.0002982 - 0.0001553 = 0.0001429 eq. of Ag+.
tAg+ = (eq. of Ag+ lost from anode)/(eq. of Cu deposited) = 0.0001429/0.0002982 = 0.479 (book 0.4792), so tNO3- = 1 - 0.4792 = 0.5208.
Teacher's Note: Active silver anode adds Ag+; migration loss = (coulometer equivalents) - (apparent gain). Water mass is the reference.
Exam Note: Compare equal masses of water before and after.
Question 28. Calculate the transport no. of H+ and Cl- ions from the following data obtained by moving boundary method using CdCl2 as the indicator electrolyte: Concentration of HCl solution = 0.1 N; Wt. of Ag deposited in coulometer = 0.1209 g; Movement of boundary = 7.50 cm; Cross-section of tube = 1.24 cm2.
Solution.
Transport no. of H+ = l·A·C/(1000 Q), where l = length of migration = 7.50 cm, A = area of cross-section = 1.24 cm2, C = concentration of solution = 0.1 N, and Q = charge passed = equivalents of Ag deposited = 0.1209/108 Faraday (Q = W/E).
tH+ = 7.5 × 1.24 × 0.1 × 108/(0.1209 × 1000) = 0.8308.
tH+ + tCl- = 1, so tCl- = 1 - 0.8308 = 0.1692.
Teacher's Note: Moving boundary: equivalents of H+ swept = lAC/1000; divide by Faradays passed (Ag deposited/108).
Exam Note: Use equivalent weight of Ag = 108 for Faradays.
Question 29. Calculate the conductivity (in 1 × 10-7 S m-1 unit) of a solution prepared by dissolving 10-7 mole of AgNO3 in 1 litre of saturated aqueous solution of AgBr. Ksp of AgBr = 12 × 10-14 and λ°Ag+, λ°Br- and λ°NO3- are 6 × 10-3, 8 × 10-3 and 7 × 10-3 S m2 mol-1 respectively. Neglect the contribution of solvent. (IIT 2006)
Solution.
Solubility of AgBr in presence of 10-7 mole of AgNO3: Ksp = [Ag+][Br-], so 12 × 10-14 = [S + 10-7] × S, giving S = 3 × 10-7 M.
[Ag+] = 3 × 10-7 + 10-7 = 4 × 10-7 M; [Br-] = 3 × 10-7 M; [NO3-] = 1 × 10-7 M.
κ = Λ° × M/1000 (λ in S m2 mol-1 is λ × 104 in S cm2 mol-1).
κAg+ = 6 × 10-3 × 104 × 4 × 10-7/1000 = 24 × 10-9 S cm-1; κBr- = 8 × 10-3 × 104 × 3 × 10-7/1000 = 24 × 10-9 S cm-1; κNO3- = 7 × 10-3 × 104 × 10-7/1000 = 7 × 10-9 S cm-1.
κtotal = 24 × 10-9 + 24 × 10-9 + 7 × 10-9 = 55 × 10-9 S cm-1 = 55 × 10-7 S m-1.
In the unit of 1 × 10-7 S m-1, the conductivity is 55.
Teacher's Note: Common-ion effect first: (S + 10-7)S = Ksp; then sum each ion's λ × concentration.
Exam Note: Watch unit conversion S cm-1 to S m-1: multiply by 100.
Single Integer Answer Problems
Question SI 1. The conductance of a 0.0015 M aqueous solution of a weak monobasic acid was determined by using a conductivity cell consisting of platinized Pt electrodes. The distance between the electrodes is 120 cm with an area of cross-section of 1 cm2. The conductance of this solution was found to be 5 × 10-7 S. The pH of the solution is 4. The value of limiting molar conductivity (Λ°M) of this weak monobasic acid in aqueous solution is Z × 102 S cm-1 mol-1. The value of Z is: [JEE (Main) 2017]
Solution.
Answer (from key): Six (Z = 6).
Working: κ = G × (l/a) = 5 × 10-7 × 120 = 6 × 10-5 S cm-1. ΛM = κ × 1000/C = 6 × 10-5 × 1000/0.0015 = 40 S cm2 mol-1.
pH = 4, so [H+] = 10-4 and α = 10-4/0.0015 = 0.0667. Λ°M = ΛM/α = 40/0.0667 = 600 = 6 × 102 S cm2 mol-1, so Z = 6.
Teacher's Note: Conductance times l/a gives κ; α comes from pH; then Λ° = Λ/α.
Exam Note: Convert pH to [H+]; α = [H+]/C.
Objective Problems (One Answer Correct)
Question Obj 1. The resistance of 0.05 N solution of an electrolyte AaBb was found to be 210 ohm at 300 K. If cell constant is 0.88 cm-1, the molar conductivity in S m2 mol-1 is:
(a) 83.81 × (a + b)
(b) 83.81 × (a + b) × 10-4
(c) 83.81 × (a · b)
(d) 83.81 × (a · b) × 10-4
Solution.
Answer: (d).
ΛM = κ × 1000/CM (κ = C × l/a). Here κ = (1/210) × 0.88 and, for AaBb, N = M × (a · b), so CM = 0.05/(a · b).
ΛM = (0.88/210) × 1000 × (a · b)/0.05 = 83.81 × a × b × 10-4 S m2 mol-1.
Teacher's Note: Charge per formula unit is a·b, so M = N/(a·b); 1 S cm2 mol-1 = 10-4 S m2 mol-1.
Exam Note: Convert units at the end: multiply by 10-4.
Question Obj 2. If ΛM of a solution is 419 × 10-4 S m2 mol-1 for an electrolyte K2SO4 at 300 K. The resistance offered by the solution with cell constant 0.88 m-1 is 210 ohm, the molarity of K2SO4 solution is:
(a) 1 × 10-4 M
(b) 0.02 M
(c) 0.05 M
(d) 0.03 M
Solution.
Answer: (a).
ΛM = κ/c (c in mol m-3, κ in ohm-1 m-1): 419 × 10-4 = (0.88/210)/c.
c = 0.1 mol m-3 = 1 × 10-4 M.
Teacher's Note: In SI, ΛM = κ/c with c in mol m-3; 1 mol m-3 = 10-3 M.
Exam Note: Convert mol m-3 to M by dividing by 1000.
Question Obj 3. The molar conductivity of LiNO3 at infinite dilution is 105 S cm2 mol-1. If 0.02 M solution shows conductance 0.158 ohm-1 using cell of cell constant 1 cm-1. The concentration of Li+ ion in g litre-1 is:
(a) 0.01106
(b) 0.1106
(c) 11.06
(d) 0.2212
Solution.
Answer: (a).
Λv = κ × 1000/M = 0.158 × 1000/0.02 = 7900 S cm2 mol-1; α = Λv/Λ∞ = 7900/105 = 0.079.
[Li+] = cα = 0.02 × 0.079 = 1.58 × 10-3 M, so wLi+ = 1.58 × 10-3 × 7 = 0.01106 g/litre.
Teacher's Note: Find α from Λ/Λ∞, then ion concentration cα; convert mol/L to g/L with atomic mass 7.
Exam Note: Multiply [Li+] by 7 g mol-1 for g/litre.
Question Obj 4. One needs some experimental data to determine Λ°H2C2O4. Which value is also needed in addition of Λ°HNO3 and Λ°K2C2O4?
(a) Λ°NaCl
(b) Λ°KNO3
(c) Λ°KCl
(d) Λ°Na2C2O4
Solution.
Answer: (b).
Λ°H2C2O4 = 2λ°H+ + λ°C2O42- = 2Λ°HNO3 + Λ°K2C2O4 - 2Λ°KNO3.
Teacher's Note: Build the target from ions: cancel NO3- and K+ using 2 × KNO3.
Exam Note: Write the combination to justify choosing KNO3.
Question Obj 5. The transport number of Ag+ in AgNO3 is 0.4 and of NO3- in KNO3 is 0.4. The ratio of transport number of NO3- in AgNO3 and KNO3 is:
(a) 1
(b) 1.5
(c) 2.0
(d) 2.5
Solution.
Answer: (b).
tNO3- in AgNO3 = 1 - 0.4 = 0.6; in KNO3 it is 0.4. Ratio = 0.6/0.4 = 1.5.
Teacher's Note: t+ + t- = 1 within each salt; transport numbers differ between salts.
Exam Note: Use 1 - 0.4 for the AgNO3 value.
Question Obj 6. The absolute velocity of Ag+ and NO3- are 5.7 × 10-4 and 6.9 × 10-4 cm sec-1 respectively. Assuming complete dissociation of AgNO3, calculate the molar conductivity of AgNO3 at infinite dilution:
(a) 121.59 S cm2 mol-1
(b) 141.59 S cm2 mol-1
(c) 131.59 S cm2 mol-1
(d) none of these
Solution.
Answer: (a).
λ° = u° × F. λ°Ag+ = 5.7 × 10-4 × 96500; λ°NO3- = 6.9 × 10-4 × 96500. Λ°M AgNO3 = (5.7 × 10-4 + 6.9 × 10-4) × 96500 = 121.59 S cm2 mol-1.
Teacher's Note: Ion mobilities add; multiply the sum by 96500.
Exam Note: Add mobilities first, then multiply by F once.
Question Obj 7. The conductivity of 20 mL of 0.2 N NaOH solution is a S cm-1. If 10 mL of 0.4 N HCl solution is added to this solution, the conductivity decreases by b S cm-1. The resultant solution has equivalent conductivity in S cm2 eq.-1 is:
(a) a - b
(b) (a - b) × 30/4
(c) (a - b) × 3 × 104/4
(d) (a - b) × 4/3
Solution.
Answer: (c).
NaOH + HCl → NaCl + H2O: 20 × 0.2 = 4 and 10 × 0.4 = 4 milli-equivalents react completely, leaving 4 meq of NaCl in 30 mL, so [NaCl] = 4/30 N.
The final conductivity is (a - b), so Λeq = κ × 1000/N = (a - b) × 1000 × 30/4 = (a - b)/4 × 3 × 104 S cm2 eq.-1.
Teacher's Note: Neutralisation leaves NaCl: 4 meq in 30 mL; use Λ = 1000κ/N.
Exam Note: Use total volume 30 mL, not 20 mL.
Question Obj 8. Molar conductivity of AgNO3, HCl and HNO3 at infinite dilution are a, b, c S cm2 mol-1 respectively. If the conductivity of saturated AgCl solution is Z S cm-1, then Ksp of AgCl will be:
(a) 1000Z/(a + b - c)
(b) [1000Z/(a + b - c)]2
(c) [(a + b - c)/Z]
(d) [(a + b - c)/(Z × 1000)]2
Solution.
Answer: (b).
Λ°AgCl = λ°Ag+ + λ°Cl- = a + b - c (AgNO3 + HCl - HNO3).
Λ°AgCl = κ × 1000/M: (a + b - c) = Z × 1000/M, so M = 1000Z/(a + b - c).
Ksp = [Ag+][Cl-] = M2 = [1000Z/(a + b - c)]2.
Teacher's Note: AgNO3 + HCl - HNO3 gives AgCl; solubility M = 1000κ/Λ°, Ksp = M2.
Exam Note: Remember to square M for Ksp.
Question Obj 9. Which of the following correctly represents equivalent conductance of Al2(SO4)3 at infinite dilution:
(a) 2λ∞Al3+ + 3λ∞SO42-
(b) 2λ∞Al3+ + λ∞SO42-
(c) [λ∞Al3+ + λ∞SO42-] × 6
(d) (1/3)λ∞Al3+ + (1/2)λ∞SO42-
Solution.
Answer: (d).
Follow Kohlrausch law: Λ°eq = (1/n+)λ°+ + (1/n-)λ°- with n+ = 3 and n- = 2. (Options (a) and (b) are molar-type expressions.)
Teacher's Note: Equivalent conductance divides each ionic conductance by its charge.
Exam Note: Distinguish equivalent (divide by charge) from molar (multiply by number).
Question Obj 10. The best conductor of electricity in 0.1 M aqueous solution:
(a) Boric acid
(b) Sulphuric acid
(c) Acetic acid
(d) Propionic acid
Solution.
Answer: (b).
H2SO4 is a strong electrolyte and furnishes the maximum number of ions per formula unit (2H+ + SO42-); the others are weak acids.
Teacher's Note: Strong electrolyte with the most ions wins; H+ is also highly mobile.
Exam Note: Strong acid + highest ion count = best conductor.
Question Obj 11. An increase in equivalent conductivity of strong electrolytes with dilution is mainly due to:
(a) increase in ionic mobility of ions
(b) 100% ionisation of electrolyte at normal dilution
(c) increase in both i.e., mobility and ionisation
(d) increase in number of ions
Solution.
Answer: (a).
Strong electrolytes are already fully ionised; on dilution interionic attractions decrease, so ionic mobility increases.
Teacher's Note: No change in ionisation for strong electrolytes; only interionic effects change.
Exam Note: Strong: mobility changes; weak: ionisation changes.
Question Obj 12. The molar conductivity of 1 M HCl is greater than 1 M NaCl at a particular temperature. This is due to:
(a) molar mass of HCl < molar mass of NaCl
(b) ionic mobility of H+ > ionic mobility of Na+
(c) HCl being an acid has lower pH
(d) degree of ionisation of HCl > degree of ionisation of NaCl
Solution.
Answer: (b).
Ionic mobility of H+ is maximum because it is the lightest ion (and it also moves by proton hopping); both HCl and NaCl are strong electrolytes.
Teacher's Note: Both are strong electrolytes, so the difference lies in ion mobility, not ionisation.
Exam Note: Compare mobilities: λ°(H+) is exceptionally high.
Question Obj 13. SI Unit of ionic mobility is:
(a) m2 volt-1 sec-1
(b) cm2 volt-1 sec-1
(c) cm volt-1 sec-1
(d) cm2 volt sec-1
Solution.
Answer: (a).
Ionic mobility = speed of ion/potential gradient = (m s-1)/(volt m-1) = m2 volt-1 sec-1.
Teacher's Note: Speed divided by field strength; SI uses metre, not centimetre.
Exam Note: cm2 is CGS-type; SI needs m2.
Question Obj 14. Molten sodium chloride conducts electricity due to the presence of:
(a) Free electrons
(b) Free ions
(c) Free molecules
(d) Atoms of sodium and chlorine
Solution.
Answer: (b).
NaCl (fused) → Na+ + Cl-; the free ions carry the current.
Teacher's Note: Ionic compounds conduct in the molten state because ions become mobile.
Exam Note: Answer "free ions", not electrons.
Question Obj 15. Which of the following is always an additive property:
(a) Conductance
(b) Resistance
(c) Surface tension
(d) Viscosity
Solution.
Answer: (a).
Csolution = Celectrolyte + Cwater: conductances of parallel conducting paths add, resistances do not.
Teacher's Note: Conductance adds like parallel paths; resistance does not add for ions in one solution.
Exam Note: Use this to subtract solvent conductance in numericals.
Question Obj 16. Which of the following ion has exceptionally higher values of Λ∞:
(a) H+
(b) K+
(c) NH2-
(d) NH4+
Solution.
Answer: (a).
H+ has an exceptionally high ionic conductance because of its smallest size (and Grotthuss proton hopping).
Teacher's Note: H+ (about 350 S cm2 eq.-1) is far above other cations.
Exam Note: Mention proton hopping if asked to explain.
Question Obj 17. At infinite dilution the solution of CH3COOH does not contain:
(a) H+
(b) CH3COO-
(c) CH3COOH
(d) None of these
Solution.
Answer: (c).
At infinite dilution α = 1, so CH3COOH → CH3COO- + H+ is complete and no undissociated molecules remain.
Teacher's Note: Infinite dilution means 100% dissociation even for weak electrolytes.
Exam Note: Weak electrolytes also have α = 1 at infinite dilution.
Question Obj 18. Select the correct statement:
(a) Λ∞ of strong electrolytes can be obtained only by Kohlrausch's law
(b) Mobility of ions depends only on nature of ion
(c) Speed of ion depends only on nature of ion
(d) Conductance of solution decreases with increase in temperature
Solution.
Answer: (b).
Mobility of an ion is its speed under unit potential gradient, so it depends on the nature of the ion; speed also depends on the applied gradient.
Teacher's Note: Mobility is speed per unit field; speed itself also depends on the field.
Exam Note: Mobility is not the same as speed.
Question Obj 19. The molar conductivity of NaCl, KCl and K2SO4 at 25°C and infinite dilution are 126.45, 149.84, 306.60 S cm2 mol-1 respectively. If λ°Na+ at 25°C is 50.11 S cm2 mol-1, what is λ°SO42- (in S cm2 mol-1) at 25°C:
(a) 159.6
(b) 209.77
(c) 259.82
(d) 359.82
Solution.
Answer: (a).
Λ°Na2SO4 = 2Λ°NaCl + Λ°K2SO4 - 2Λ°KCl = 2 × 126.45 + 306.60 - 2 × 149.84 = 259.82.
λ°SO42- = Λ°Na2SO4 - 2λ°Na+ = 259.82 - 2 × 50.11 = 159.6 S cm2 mol-1.
Teacher's Note: Construct Na2SO4 from the three data, then subtract two Na+.
Exam Note: Do not stop at 259.82; subtract 2λ(Na+).
Question Obj 20. Ionic mobility of which of the following alkali metal ions is lowest when aqueous solution of their salts are put under an electric field?
(a) Na
(b) K
(c) Rb
(d) Li
Solution.
Answer: (d).
Enthalpy of hydration of Li+ is maximum among the given species. Size of ion: Li+ < Na+ < K+ < Rb+; size of hydrated ion: Li+(aq.) > Na+(aq.) > K+(aq.) > Rb+(aq.). Thus ionic mobility will be minimum for Li+(aq.).
Teacher's Note: Smallest ion, most hydrated, biggest hydrated radius, slowest in water.
Exam Note: Reason with hydrated radius, not bare ionic radius.
Previous Years Problems
Question PY 1. The correct order of equivalent conductivity at infinite dilution of LiCl, NaCl and KCl is: (IIT 2001)
(a) LiCl > NaCl > KCl
(b) KCl > NaCl > LiCl
(c) NaCl > KCl > LiCl
(d) LiCl > KCl > NaCl
Solution.
Answer: (b).
More is the size of hydrated ion (Li+(aq.) > Na+(aq.) > K+(aq.)), lesser is the conductance. Hence KCl > NaCl > LiCl.
Teacher's Note: Hydrated size order is reverse of bare size; mobility follows hydrated size inversely.
Exam Note: Quote hydrated radius order Li > Na > K.
Question PY 2. AgNO3(aq) was added to an aqueous KCl solution gradually and the conductivity of the solution was measured. The plots of conductance Λ vs volume of AgNO3(aq) is: (IIT 2011)
Graphs (Λ on the vertical axis, V on the horizontal axis): (a) Λ falls in a straight line to a sharp minimum, then rises in a straight line; (b) Λ falls gently to a rounded minimum, then rises steeply; (c) Λ falls to a shallow dip, rises slightly to a hump, then falls in a straight line; (d) Λ stays constant (horizontal line) and then rises in a straight line.
Solution.
Answer: (d).
Initial conductance of the solution was due to K+ and Cl-. On addition of AgNO3, the reaction AgNO3(aq) + KCl(aq) → AgCl↓ + KNO3(aq) occurs. ΛKCl ≈ ΛKNO3 till complete precipitation (Cl- replaced by NO3- of similar mobility), and then conductance increases with further addition of AgNO3.
Teacher's Note: Cl- is replaced by NO3- of similar mobility, so conductance is flat until the end point.
Exam Note: Flat before equivalence, rising after: excess Ag+ and NO3-.
Question PY 3. Resistance of 0.2 M solution of an electrolyte is 50 Ω. The specific conductance of the solution is 1.4 S m-1. The resistance of 0.5 M solution of the same electrolyte is 280 Ω. The molar conductivity of 0.5 M solution of the electrolyte in S m2 mol-1 is: [JEE (Main) 2014]
(a) 5 × 10-4
(b) 5 × 10-3
(c) 5 × 103
(d) 5 × 102
Solution.
Answer: (a).
κ = (1/R)(l/a). For the 0.2 M solution κ = 1.4 S m-1 = 1.4 × 10-2 S cm-1, so l/a = 1.4 × 10-2 × 50 = 0.7 cm-1.
For the 0.5 M solution: Λm = κ × 1000/C = (1/R)(l/a)(1000/C) = (1/280) × 0.7 × 1000/0.5 = 5 S cm2 mol-1 = 5 × 10-4 S m2 mol-1.
Teacher's Note: Same cell: l/a = κ × R from the first solution, reuse it with the second resistance.
Exam Note: Convert S cm2 mol-1 to S m2 mol-1 by 10-4.
Question PY 4. The equivalent conductance of NaCl at concentration C and at infinite dilution are λC and λ∞ respectively. The correct relationship between λC and λ∞ is given as: (where the constant B is positive) [JEE (Main) 2014]
(a) λC = λ∞ + (B)C
(b) λC = λ∞ - (B)C
(c) λC = λ∞ - (B)√C
(d) λC = λ∞ + (B)√C
Solution.
Answer: (c).
This is called Onsager's equation (Debye-Hückel-Onsager): for strong electrolytes ΛC = Λ∞ - B√C.
Teacher's Note: Strong electrolytes: Λ falls linearly with √C (Kohlrausch/Onsager).
Exam Note: Square root of concentration, with a negative sign.
Question PY 5. The qualitative sketches I, II and III given below show the variation of surface tension with molar concentration of three different aqueous solution of KCl, CH3OH and CH3(CH2)11OSO3-Na+ at room temperature. The correct assignment of the sketches is: [JEE (Advanced) II 2016]
Sketches (surface tension vs concentration): I falls slightly and then flattens; II rises slowly and linearly; III falls very sharply and then stays flat at low value.
(a) I : KCl; II : CH3OH; III : CH3(CH2)11OSO3-Na+
(b) I : CH3(CH2)11OSO3-Na+; II : CH3OH; III : KCl
(c) I : KCl; II : CH3(CH2)11OSO3-Na+; III : CH3OH
(d) I : CH3OH; II : KCl; III : CH3(CH2)11OSO3-Na+
Solution.
Answer: (d).
Corrected: the book's key gives (c), but the correct answer is (d).
Detergents like CH3(CH2)11OSO3-Na+ decrease surface tension sharply due to micellization (sketch III). Alcohols such as CH3OH lower the surface tension slightly (lower dielectric constant, weaker H-bonding in the mixture) (sketch I). Soluble inorganic impurities such as KCl slightly increase the surface tension of water, because ions increase intermolecular attraction (sketch II).
Hence I : CH3OH; II : KCl; III : surfactant, which is option (d).
Teacher's Note: Surfactant: sharp fall. Alcohol: slight fall. Salt: slight rise in surface tension.
Exam Note: Match shapes: sharp fall = detergent; slight rise = KCl.
Objective Problems (More Than One Answer Correct)
Question MA 1. Which one is correct statement?
(a) Conductance is an additive property
(b) Conductance order: Li+(aq.) < Na+(aq.) < K+(aq.) < Rb+(aq.)
(c) Molar conductivity of NH4+ in liquid NH3 is higher than in H2O
(d) At infinite dilution all the interionic attractions vanishes
Solution.
Answer: (a, b, c, d).
(a) CT = ΣCi + Cwater.
(b) Due to more hydration of small cation, the hydrated size increases and conductance decreases.
(c) Due to Grotthus conductance; conductance of NH4+ in NH3 is more.
(d) At infinite dilution, ions are so far apart that interionic attractions vanish.
Teacher's Note: Conductance adds; hydrated radius decreases from Li to Rb so conductance rises; interionic forces vanish at infinite dilution.
Exam Note: All four statements are standard facts; verify each separately.
Question MA 2. Which relations are correct about conductances?
(a) Kb = CΛv2/[Λ°(Λ° - Λv)]
(b) α = Λv/Λ∞ for strong electrolytes
(c) Λ°M AXBY = XΛ°A+ + YΛ°B-
(d) ΛM = κ × 1000/M
Solution.
Answer: (a, c, d).
α = Λv/Λ° holds for weak electrolytes only, so (b) is wrong. (a) follows from K = Cα2/(1 - α) with α = Λv/Λ°; (c) is Kohlrausch law; (d) is the definition of molar conductivity.
Teacher's Note: Ostwald: K = CΛv2/[Λ°(Λ° - Λv)] for weak electrolytes; strong ones are fully ionised already.
Exam Note: Reject (b): α = Λ/Λ° is only for weak electrolytes.
Question MA 3. Select the correct statements:
(a) Λ°M for weak electrolytes depends upon degree of dissociation of electrolyte, ionic mobility and nature of ion
(b) Λ°M for strong electrolytes depends upon ionic mobility and nature of ion
(c) The SI unit of ΛM is S m2 mol-1
(d) 1 S m2 mol-1 = 1 × 104 S cm2 mol-1
Solution.
Answer: (a, b, c, d).
These are facts: 1 m2 = 104 cm2, so 1 S m2 mol-1 = 104 S cm2 mol-1.
Teacher's Note: Unit conversion m2 to cm2 gives the factor 104.
Exam Note: Memorise: S m2 mol-1 = 104 S cm2 mol-1.
Question MA 4. A graph plotted for log (i - 1) vs. log Λv, where i is van't Hoff factor of given uni-univalent electrolyte having molar conductance Λv at dilution v, then which are correct?
(a) Slope = -log Λ°; intercept = -1
(b) Slope = 1; intercept = -log Λ°M
(c) Slope = 1; intercept = log Λ°M
(d) Slope = log Λ°M; intercept = +1
Solution.
Answer: (b).
α = (i - 1)/(n - 1) with n = 2 for AB, so Λv/Λ°M = (i - 1)/1, i.e. i - 1 = Λv/Λ°M.
log (i - 1) = log Λv - log Λ°M, which is of the form Y = mx + c: slope = 1 and intercept = -log Λ°M.
Teacher's Note: For a binary electrolyte i = 1 + α and α = Λv/Λ°, then take logs.
Exam Note: Intercept is negative: -log Λ°.
Question MA 5. Λ°M and Λ°E are molar and equivalent conductivity at infinite dilution and λ° is ionic conductance at infinite dilution, then for potash alum:
(a) Λ°M = 2 × λ°K+ + 2 × λ°Al3+ + 4 × λ°SO42-
(b) Λ°E = (1/8) × Λ°M
(c) Λ°E = (1/4) × λ°K+ + (1/4) × λ°Al3+ + (1/2) × λ°SO42-
(d) Λ°M = λ°K+ + λ°Al3+ + λ°SO42-
Solution.
Answer: (a, b, c).
Potash alum K2SO4·Al2(SO4)3·24H2O gives 2K+, 2Al3+ and 4SO42- per formula unit (8 equivalents). So Λ°M = 2λ°K+ + 2λ°Al3+ + 4λ°SO42-, Λ°E = Λ°M/8 = (1/4)λ°K+ + (1/4)λ°Al3+ + (1/2)λ°SO42-.
Teacher's Note: Count ions per formula unit: 2, 2, 4; equivalents = total positive charge = 8.
Exam Note: Option (d) ignores stoichiometric numbers, so it is wrong.
Question MA 6. An ion travels 0.4 cm in 1 minute under the influence of 2 volt potential difference when electrodes are 3 cm apart. Which one are correct?
(a) Speed of ion = 6.67 × 10-3 cm s-1
(b) Ionic mobility = 1 × 10-6 m2 volt-1 sec-1
(c) Ionic mobility = 1.0 × 10-3 cm2 volt-1 sec-1
(d) Ionic mobility = 4.44 × 10-3 cm2 volt-1 sec-1
Solution.
Answer: (a, b).
Speed = 0.4/60 = 6.67 × 10-3 cm sec-1 = 6.67 × 10-5 m sec-1.
Ionic mobility = speed/potential gradient = 6.67 × 10-5/(2/(3 × 10-2)) = 1 × 10-6 m2 volt-1 sec-1 (= 1 × 10-2 cm2 volt-1 sec-1, so (c) and (d) are wrong).
Teacher's Note: Mobility = speed ÷ (V/l). Here gradient = 2/3 V cm-1.
Exam Note: Check units: 1 m2 = 104 cm2.
Question MA 7. The increase in ionic mobility of strong electrolytes with dilution is due to:
(a) Increase in degree of dissociation
(b) Increase in number of ions
(c) Relaxation or Assymetric effect
(d) Solution or Electrophoretic effect
Solution.
Answer: (c, d).
Follow Debye-Hückel theory of strong electrolytes: on dilution the relaxation (asymmetry) effect and the electrophoretic effect decrease, so mobility increases.
Teacher's Note: Strong electrolytes are fully ionised; mobility changes via the two interionic effects.
Exam Note: Name both: asymmetry and electrophoretic effect.
Question MA 8. The formula, α = Λv/Λ∞ does not hold good for:
(a) CH3NH2
(b) H2SO4
(c) HClO4
(d) NH4Cl
Solution.
Answer: (b, c, d).
Corrected: the book's key gives (a), but the formula is valid only for weak electrolytes. CH3NH2 is a weak base, so the formula holds for it; H2SO4, HClO4 and NH4Cl are strong electrolytes, so the formula does not hold for them. The correct answer is (b, c, d).
Teacher's Note: α = Λ/Λ° is valid for weak electrolytes only; list the strong ones.
Exam Note: The question asks where it fails: strong electrolytes.
Question MA 9. In a solution of NH4OH, at infinite dilution, which are present:
(a) NH4OH
(b) NH4+
(c) OH-
(d) None of these
Solution.
Answer: (b, c).
At infinite dilution the weak electrolyte is completely dissociated into NH4+ and OH-.
Teacher's Note: Infinite dilution implies α = 1 for weak electrolytes too.
Exam Note: No undissociated NH4OH remains.
Question MA 10. The term infinite dilution refers for:
(a) All interionic effect disappears
(b) Weak electrolytes are 100% dissociated
(c) The Kohlrausch law becomes valid for weak and strong electrolytes both
(d) Ionic mobility becomes constant
Solution.
Answer: (a, b, c, d).
All four are facts about infinite dilution: ions are far apart, weak electrolytes are fully dissociated, Kohlrausch law applies to all electrolytes, and mobility reaches a constant limiting value.
Teacher's Note: At infinite dilution every electrolyte is fully ionised and ions move independently.
Exam Note: Learn the four consequences together.
Question MA 11. Which are correct for super conductors?
(a) possess zero resistivity
(b) possess infinite conductivity
(c) Metals and their alloys at 0 to 15 K
(d) Ceramic materials and mixed oxides at 0 to 150 K
Solution.
Answer: (a, b, c, d).
These are facts about superconductors: zero resistivity (infinite conductivity); metals and alloys become superconducting at 0 to 15 K and ceramic materials and mixed oxides at 0 to 150 K.
Teacher's Note: Superconductivity: zero resistance below a critical temperature.
Exam Note: Memorise the temperature ranges as given.
Question MA 12. Which one is incorrect?
(a) 1 J = 1 N × 1 m
(b) 1 J = 1 volt-coulomb
(c) 1 J = 1 watt × 1 sec
(d) 1 J = 1 volt × 1 ampere × 1 sec
Solution.
Answer: (a, b, c, d) as printed in the key.
Answer (from key): (a, b, c, d) - "these are facts". Check: work = force × distance (N m), volt × coulomb, watt × second and volt × ampere × second are all equal to one joule, so all four relations are correct and none is actually incorrect. The word "incorrect" in the statement appears to be a misprint of "correct".
Teacher's Note: All four are valid joule definitions, so none is incorrect.
Exam Note: Quote "J = N m = V C = W s".
Question MA 13. Molar conductivity of NH4+ and NH2- are usually higher in liquid NH3 than in water due to:
(a) Grotthus conductance
(b) Auto protolysis of solvent
(c) Higher dielectric constant of NH3
(d) High conducting nature of NH3
Solution.
Answer: (a, b).
Answer from key (a, b): proton transfer (Grotthus-type conduction) and auto-protolysis of the solvent (2NH3 ⇌ NH4+ + NH2-) account for the high values.
Teacher's Note: NH4+ and NH2- conduct by proton jumps, like H3O+ and OH- in water.
Exam Note: Link to Grotthus mechanism and autoprotolysis.
Question MA 14. Which of the following will increase the conductivity of solution:
(a) Temperature
(b) Dielectric constant of solvent
(c) Decrease in viscosity of solvent
(d) Decrease in solvation of ion
Solution.
Answer: (a, b, c, d).
These are facts: higher temperature, higher dielectric constant, lower viscosity and smaller solvated size all increase ionic mobility or ionisation and hence conductivity.
Teacher's Note: Conductivity rises with ion mobility and number of free ions.
Exam Note: Temperature raises conductivity of electrolytes (unlike metals).
Comprehension Based Problems
Comprehension 1. Electrolytes that are known as weak electrolytes on the basis of very strong dependence of conductance on concentration give quite constant concentration independent values of dissociation constant (Ka) calculated from degree of dissociation (α) values from measured conductances or from colligative properties. The partial dissociation appears to be a major factor in determining the properties of weak electrolytes and the degree of dissociation for weak electrolyte at dilution v is given by α = Λv/Λ∞. The strong electrolytes on the other hand do not obey this relation and the variation of molar conductivity for strong electrolytes is given by Λv = Λ∞ - bc1/2.
Question Comp 1.1. The slope of the graph Λv2/[Λ∞(Λ∞ - Λv)] vs. 1/c, if Λv and Λ∞ are molar conductivity of weak electrolyte having dissociation constant Ka at concentration c and zero respectively is:
(a) concave downwards
(b) concave upwards
(c) straight line with intercept Ka
(d) straight line with slope Ka
Solution.
Answer: (d).
Ka = cα2/(1 - α) = cΛv2/[Λ∞(Λ∞ - Λv)], so Λv2/[Λ∞(Λ∞ - Λv)] = Ka × (1/c), a straight line y = mx with x = 1/c, slope Ka and zero intercept.
Teacher's Note: Rearrange Ostwald's law into y = mx form with x = 1/c.
Exam Note: Slope is Ka, intercept is zero.
Question Comp 1.2. The numerical value of Λ∞ion:
(a) is dependent on nature of ion
(b) is called molar conductivity
(c) is obtained by extrapolation of Λc vs. √c curves to zero concentration for all electrolytes
(d) is equal to Λv/α for strong electrolytes
Solution.
Answer: (a).
Λ∞ (ionic) depends on the nature of the ion.
Teacher's Note: Limiting ionic conductance is a property of the ion alone.
Exam Note: Extrapolation works only for strong electrolytes, so (c) fails.
Question Comp 1.3. The van't Hoff factor for weak electrolyte AxBy, if (n = x + y) can be given as:
(a) i = 1 - α + xα + yα
(b) i = 1 + (x + y) at infinite dilution
(c) i = (n - 1)Λv/Λ∞ + 1
(d) either of these
Solution.
Answer: (d).
All are correct: i = 1 - α + xα + yα, so α = (i - 1)/[(x + y) - 1] = (i - 1)/(n - 1). Also Λv/Λ∞ = (i - 1)/(n - 1), so i = (n - 1)Λv/Λ∞ + 1. At infinite dilution α = 1, so i = 1 - 1 + x + y = n, i.e. i = x + y.
Teacher's Note: i = 1 + (n - 1)α with α = Λv/Λ∞; at α = 1, i = n.
Exam Note: Link i, α and Λ ratio in one line.
Question Comp 1.4. The graph plotted for log (i - 1) vs. log Λv, where i is van't Hoff factor of uni-univalent electrolyte and Λv is its molar conductivity at concentration c does not show the following characteristics:
(a) straight line
(b) slope equal to unity
(c) intercept equal to log Λ∞
(d) intercept equal to - log Λ∞
Solution.
Answer: (c).
For HA, n = 2, so i = Λv/Λ∞ + 1 and log (i - 1) = log Λv - log Λ∞. So the graph is a straight line with slope 1 and intercept = - log Λ∞; it does not show intercept = + log Λ∞.
Teacher's Note: Take logs of i - 1 = Λv/Λ∞: slope 1, intercept -log Λ∞.
Exam Note: The question asks for the characteristic NOT shown.
Question Comp 1.5. Which statement is wrong about the variation of molar conductivity with dilution for a given electrolyte?
(a) Depends upon ionic mobility and degree of dissociation of all electrolytes
(b) Depends upon ionic mobility and degree of dissociation of weak electrolytes
(c) Depends upon ionic mobility for strong electrolytes
(d) Depends upon the nature of ion furnished by electrolytes on dissolution
Solution.
Answer: (a).
For strong electrolytes, α has no effect on ΛM (they are fully dissociated); only ionic mobility changes. So (a) is wrong.
Teacher's Note: Strong electrolytes: only mobility varies; weak: mobility and α both.
Exam Note: Look for the word "all" in the wrong statement.
Statement Explanation Problems
In each sub question given below a statement (S) and explanation (E) is given. Choose the correct answers from the codes (a), (b), (c) and (d) given for each question: (a) S is correct but E is wrong; (b) S is wrong but E is correct; (c) Both S and E are correct and E is correct explanation of S; (d) Both S and E are correct but E is not correct explanation of S.
Question SE 1. S: A graph plotted between Λv vs. c1/2 gives a straight line with slope equal to -A and intercept equal to Λ∞.
E: The value of A for a given solvent and temperature depends upon the nature of electrolyte, i.e., charge on cation or anion furnished by electrolyte on dissolution.
Solution.
Answer: (d).
Both are facts: Λv = Λ∞ - A√c and A depends on the type of electrolyte (charges on ions), but this does not explain why the plot is a straight line.
Teacher's Note: Debye-Hückel-Onsager: A depends on solvent, temperature and ion charges.
Exam Note: Both true, but E does not explain S.
Question SE 2. S: Conductivity of weak electrolyte solution decreases with dilution whereas equivalent conductivity, molar conductivity increases with dilution.
E: On dilution, the ionic mobility and number of ions present in solution increases but number of ions per mL decreases.
Solution.
Answer: (c).
Explanation is correct reason for statement: conductivity depends on ions per mL (which falls on dilution), while molar and equivalent conductivities are referred to a fixed amount of electrolyte, for which ionisation and mobility increase.
Teacher's Note: κ tracks ions per mL (falls); Λ is per mole or equivalent (rises).
Exam Note: Distinguish κ (per cm3) from Λ (per mole).
Question SE 3. S: The Λ∞ for all electrolytes can be obtained by extrapolation of ΛM curves vs. √concentration to zero concentration.
E: Λ∞ for all electrolytes can be obtained by Kohlrausch law.
Solution.
Answer: (b).
Λc vs. √c curves give Λ∞ values on extrapolation to zero concentration for strong electrolytes only (weak electrolytes do not give a straight line). Kohlrausch law gives Λ∞ for all, so S is wrong and E is correct.
Teacher's Note: Extrapolation fails for weak electrolytes; Kohlrausch law covers both.
Exam Note: Say "strong electrolytes only" for extrapolation.
Question SE 4. S: The ratio of speeds of cation and anions of an electrolyte under same potential gradient is 2 : 3, the fall in concentration around anodic and cathodic solution will be in the ratio 1 : 1 during the passage of current.
E: The number of ions discharged at either electrode during electrolysis is independent of their relative speed.
Solution.
Answer: (b).
The number of ions discharged on opposite electrodes is independent of their relative speed, however the fall in concentration around any electrode depends upon the speed of the ion moving away from it. So the fall around anode and cathode is in the ratio of the speeds (2 : 3), not 1 : 1: S is wrong, E is correct.
Teacher's Note: Discharge is equal at both electrodes; concentration fall depends on speed of the departing ion.
Exam Note: Ratio of falls equals ratio of speeds.
Question SE 5. S: The conductance of ions through passage of current through an electrolyte showing autoprotolysis are abnormally higher.
E: The ions obtained during autoprotolysis show higher values due to Grotthus conduction.
Solution.
Answer: (c).
Explanation is correct reason for statement: ions from autoprotolysis (such as H3O+) conduct by proton jumping (Grotthus mechanism), giving abnormally high conductance.
Teacher's Note: Proton hopping along hydrogen-bonded solvent explains the abnormal values.
Exam Note: Name Grotthus mechanism and proton transfer.
Question SE 6. S: Conductance of a solution can be obtained by designing the apparatus based on Wheatstone bridge principle.
E: Meter bridge used to detect the resistance of metal wire can be used to read out the conductance of solutions.
Solution.
Answer: (a).
S is correct; E is wrong without modification. Some modifications such as A.C. in place of D.C., null point detector in place of galvanometer, etc., are to be made in meter bridge.
Teacher's Note: Electrolysis polarises electrodes under D.C., so A.C. and a different null detector are needed.
Exam Note: Mention A.C. source for conductance measurement.
Question SE 7. S: The conductance measurement of an electrolytic solution is made by using two conductivity cells having different cell constants gives different values of conductance.
E: The conductances of solution obtained will be different but conductivity of solution would be same.
Solution.
Answer: (d).
Both are correct. The conductivity κ is the same in both cases because the number of ions per c.c. remains same, while conductance depends on the cell constant (κ = C × l/a).
Teacher's Note: Conductance depends on cell geometry; conductivity is a property of the solution.
Exam Note: Conductivity is cell-independent; conductance is not.
Question SE 8. S: Speed of ions depends upon nature of ions only.
E: Mobility of ions depends upon mass, charge and size of ions only.
Solution.
Answer: (b).
Speed of ions depends upon nature of ions and the potential gradient. So S is wrong; E is as given in the key (mobility is speed under unit potential gradient and depends on the nature of the ion), so (b).
Teacher's Note: Speed = mobility × potential gradient, so speed also depends on the applied field.
Exam Note: Speed depends on field; mobility does not.
Matching Type Problems
Type I: More Than One Match Are Possible
Question Match 1. Match List A with List B.
List A: (A) Λ vs c1/2 plots; (B) Kohlrausch law.
List B: 1. Λ° for strong electrolyte; 2. Hyperbolic graph; 3. Straight line graph; 4. Λ° for weak electrolyte.
Solution.
Answer (from key): A - 1, 2, 3; B - 1, 4.
A: Λ vs c1/2 plot gives a straight line (3) for strong electrolytes whose extrapolation to zero concentration gives Λ° (1), and a hyperbolic-type curve (2) for weak electrolytes. B: Kohlrausch law gives Λ° of both strong (1) and weak (4) electrolytes.
Teacher's Note: Λ vs √c is linear for strong electrolytes and curved for weak ones; Kohlrausch law handles both.
Exam Note: Match A to 1, 2, 3 and B to 1, 4.
Question Match 2. An aqueous solution of X is added slowly to an aqueous solution of Y as shown in List A. The variation in conductivity of these reactions using the codes given below is given in List B. Match List A with List B and select the correct answer using the code given below the lists: [JEE (Advanced) II 2013]
List A (X, Y): (P) (C2H5)3N (X) + CH3COOH (Y); (Q) KI (0.1 M) (X) + AgNO3 (0.01 M) (Y); (R) CH3COOH (X) + KOH (Y); (S) NaOH (X) + HI (Y).
List B: (1) Conductivity decreases and then increases; (2) Conductivity decreases and then does not change much; (3) Conductivity increases and then does not change much; (4) Conductivity does not change much and then increases.
Codes: (a) P-3, Q-4, R-2, S-1; (b) P-4, Q-3, R-2, S-1; (c) P-2, Q-3, R-4, S-1; (d) P-1, Q-4, R-3, S-2.
Solution.
Answer (from key): (a).
(P) Weak base added to weak acid forms the salt (ions), so conductivity increases and then stays nearly constant (weak base adds few ions): 3. (Q) K+ replaces Ag+ and I- removes Ag+ as AgI, so conductivity changes little until excess KI is added, after which it rises: 4. (R) Weak acid added to KOH: OH- is replaced by the less mobile CH3COO-, so conductivity decreases, then stays about constant (weak acid in excess adds few ions): 2. (S) NaOH added to HI: highly mobile H+ is replaced by Na+, so conductivity decreases and then increases with excess NaOH: 1.
Teacher's Note: Track which ions are replaced by slower ones; excess strong reagent raises conductivity, excess weak reagent does not.
Exam Note: Strong-strong titration: fall then rise; weak reagent: fall then flat.
Step-by-Step P Bahadur Solutions for JEE Math
Access JEE Mathematics Solutions
Review detailed solutions for JEE Mathematics. The P Bahadur Solutions Numerical Chemistry Chapter 14 Conductance Of A Solution PDF provides comprehensive answers mapped to standard P Bahadur Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Step-by-Step Mathematical Explanations
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Explore More Study Resources for JEE Math
In addition to these P Bahadur Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the P Bahadur book for JEE Chemistry. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.