Download JEE Physics LA Sena Textbook Solutions: Chapter 01 Fundamentals of Mechanics
Explore reliable textbook solutions for Chapter 01 Fundamentals of Mechanics tailored for JEE learners using LA Sena methodologies. Utilizing these Physics answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.
Access LA Sena Textbook Answers and Solutions
View or download the dedicated Chapter 01 Fundamentals of Mechanics solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Physics.
Fundamentals of Mechanics - Problems 1.1 to 1.58
Questions and Problems: Fundamentals of Mechanics
Question 1.1. A wind is blowing with a constant velocity v along the direction shown by the arrow in the figure (from B towards A along line AB). Two airplanes start from a point A and fly with a constant speed c relative to the air. One flies against the wind to a point B and then returns to A; the other flies perpendicular to the wind to a point C and then returns to A. The distances AB and AC are the same. Which plane will return to A first, and what is the ratio of the flight times of the two planes?
Solution. If AB = AC = l, the times of flight from A to B and from B to A are l/(c − v) and l/(c + v) respectively. The entire flight time is t1 = l/(c − v) + l/(c + v) = 2lc/(c2 − v2). For the second airplane to fly from A to C, its velocity must be directed at an angle to the wind so that the resultant velocity towards C has magnitude (c2 − v2)1/2 (velocity triangle: c is the hypotenuse, v and the resultant are the legs). The entire flight time is t2 = 2l/√(c2 − v2). The second airplane (the one flying perpendicular to the wind) arrives before the first, and the ratio of flight times is t2/t1 = √(1 − v2/c2).
Teacher's Note: Wind helps one way, hurts the other; the perpendicular flight loses less. Compare ground speeds, not air speeds.
Exam Note: Show velocity triangle; state ratio.
Question 1.2. A boat is moving across a river whose waters flow with a velocity u. The velocity of the boat with respect to the current, v0, is directed at an angle α to the line perpendicular to the current. At what angle θ to this line does the boat move with respect to the river banks? What is the velocity v of the boat with respect to the river banks? At what angle should the boat move so that it goes directly across the current, for given u and v?
Solution. The velocity-addition figure shows that tan θ = (v0 sin α + u)/(v0 cos α) = tan α + u/(v0 cos α). The velocity v can be found from the equation (v0 sin α + u)2 + v02 cos2 α = v2, which yields v = v0√(1 + 2(u/v0) sin α + (u/v0)2). The boat will travel directly across the river if θ = 0. Under this condition, sin α = −u/v0. Obviously, the boat can travel at right angles to the current only if v0 is greater than u.
Teacher's Note: Add boat and current velocities as vectors; zero drift needs the boat's upstream component to cancel u.
Exam Note: Draw vector triangle; state condition v0 greater than u.
Question 1.3. From a point A on a bank of a channel with still waters a person must get to a point B on the opposite bank. All the distances are shown in the figure. The person uses a boat to travel across the channel and then walks along the bank to point B. The velocity of the boat is v1 and the velocity of the walking person is v2. Prove that the fastest way for the person to get from A to B is to select the angles α1 and α2 in such a manner that (sin α1)/(sin α2) = v1/v2.
Solution. The time of travel by boat from A to C is t1 = √(x2 + a2)/v1. The time of travel by foot from C to B is t2 = √((d − x)2 + b2)/v2. The total time is t = t1 + t2 = √(x2 + a2)/v1 + √((d − x)2 + b2)/v2. The extremum condition is dt/dx = 0, or dt/dx = x/(v1√(x2 + a2)) − (d − x)/(v2√((d − x)2 + b2)) = 0. Since x/√(x2 + a2) = sin α1 and (d − x)/√((d − x)2 + b2) = sin α2, we can write sin α1/v1 = sin α2/v2, whence (sin α1)/(sin α2) = v1/v2. We can easily see that the extremum corresponds to the minimum of time of travel.
Teacher's Note: This is Snell's law of refraction in disguise: least-time path; set dt/dx = 0.
Exam Note: Write t(x), differentiate, identify the sines.
Question 1.4. An object slides without friction down an inclined plane from a point B to a point C that is distant a from a point A (A is the foot of the vertical through B; AB = h, AC = a, and the incline makes angle α with the horizontal). At what height h (or at what angle α) is the sliding time minimal?
Solution. The time of travel along the straight line BC is determined by the length S of segment BC and the acceleration w. The figure shows that S = √(a2 + h2), w = g h/√(a2 + h2). Since S = wt2/2, we can write √(a2 + h2) = (g/2)(h/√(a2 + h2)) t2, whence t = √(2(a2 + h2)/(g h)). Setting the derivative to zero, dt/dh = (h2 − a2)/(√(2g h3(a2 + h2))) = 0, yields h = a. The same result is obtained if we express S and w in terms of α: S = a/cos α, w = g sin α, t = √((2/g)(a/(sin α cos α))). Setting dt/dα = 0, we find that α = 45°.
Teacher's Note: Express time through h or α, then minimise; sinαcosα is maximal at 45 degrees.
Exam Note: Use S = wt²/2 with w = g sinα.
Question 1.5. The time dependence of the lengths of the paths of two bodies moving in a straight line is given by curves a and b, respectively (path S plotted against time t in Fig. 1.5; curve a is convex upward, curve b is concave upward). What curve corresponds to accelerated motion and what curve to decelerated motion?
Solution. The acceleration in rectilinear motion is the second derivative of the distance traveled with respect to time. For a concave curve the second derivative is positive, while for a convex curve the second derivative is negative, whereby curve (a) corresponds to decelerated motion and curve (b) to accelerated motion.
Teacher's Note: Sign of the second derivative of S(t) decides acceleration; concave up means speeding up.
Exam Note: Link curvature of S-t graph to acceleration sign.
Question 1.6. A material particle is moving along a straight line in such a manner that its velocity varies as shown in the figure (a velocity-time curve with moments 1, 2, 3, 4 marked on the time axis). At which moment in time numbered successively on the time axis will the acceleration of the particle be maximal? How should one use the graph to determine the average velocity of motion over the time interval from t1 to t2?
Solution. By definition, acceleration is the time derivative of velocity, w = dv/dt. For rectilinear motion the vector equation can be written in scalar form. The acceleration is the highest when the derivative is the greatest, that is, when the curvature of the curve is maximal. The curvature is determined by the slope of the tangent line to the particular point on the curve. This corresponds to moment 2 on the time axis. Note that for curvilinear motion the question contains an ambiguity, since to determine the acceleration we must know the radius of the trajectory at every moment in the course of the motion in addition to the magnitude of the velocity. To find the average velocity, we must know the distance traveled by the particle in the course of a definite time interval. In terms of the velocity vs. time graph, the distance traveled is the area of the figure bounded by the curve, the time axis, and the vertical straight lines passing through the initial and final moments of time on the time axis. Analytically the distance is calculated via the integral S = ∫t1t2 v dt, whence the average velocity is vav = (∫t1t2 v dt)/(t2 − t1).
Teacher's Note: Acceleration is the slope of the v-t graph; distance is the area under it.
Exam Note: Say steepest slope for acceleration; area divided by time for average.
Question 1.7. The velocity of a particle moving in a straight line varies with time in such a manner that the v vs. t curve is represented by one half of an ellipse. The maximal velocity is vm and the total time of motion is t. What is the path traversed by the particle and the average velocity over t? Can such motion actually occur?
Solution. In terms of the velocity vs. time graph, the distance traveled is determined by the area bounded by the curve and the time axis. This area is S = (π/4) vm t. The average velocity is vav = S/t = (π/4) vm. Such motion cannot be realized since at the initial and final moments of the motion the acceleration, which is dv/dt, is infinitely large in absolute value.
Teacher's Note: Half-ellipse area is (1/2)π(t/2)vm; vertical tangents at ends mean infinite acceleration.
Exam Note: Compute area; note infinite acceleration at ends.
Question 1.8. The velocity of a particle decreases in relation to the path traversed according to the linear law v = v0 − ax. After what time will the particle get to a point B that lies on the axis of abscissas distant xm from the origin of coordinates?
Solution. The particle will never get to point B but will approach it without bound. Indeed, from the equation v = v0 − ax we get dx/(v0 − ax) = dt. Integration of this expression yields ln((x − v0/a)/(−v0/a)) = −at, whence x = (v0/a)(1 − e−at). (1.8.1) The limit value xm = v0/a can be attained only at t → ∞. The dependence of x on t defined by Eq. (1.8.1) is represented by the curve shown in the figure (x rises from 0 and approaches the horizontal line x = xm asymptotically).
Teacher's Note: Separate variables dx/(v0 − ax) = dt; the logarithm shows an exponential approach.
Exam Note: Conclude t tends to infinity; do not give a finite time.
Question 1.9. The velocity of a particle moving in a straight line increases according to the linear law v = v0 + kx. How does the acceleration change in the course of such motion? Does it increase or decrease or stay constant?
Solution. The acceleration w = dv/dt = (dv/dx)(dx/dt) = k(v0 + kx) increases with x. The same result can be obtained from the following line of reasoning: at constant acceleration the relationship between the velocity and the distance traveled is given by the formula v2 = v02 + 2wx, so that the velocity increases in proportion to the square root of the distance. Hence, for the velocity to increase linearly with x, the acceleration must increase.
Teacher's Note: Use the chain rule dv/dt = (dv/dx) v; acceleration is proportional to v.
Exam Note: Show w = kv, so it grows.
Question 1.10. The figure shows the “timetable” of a train, the dependence of the speed of the train on the distance traveled. How can this graph be used to determine the average speed over the time interval it took the train to travel the entire distance?
Solution. The train covers the distance dx in the course of dt = dx/v(x), where v(x) is the speed with which it travels over dx. The total time of motion is t = ∫0S dx/v(x). The average speed is determined by dividing the distance covered by the train by the entire time of motion: vav = S/(∫0S dx/v(x)). If the graph cannot be represented by a formula, it can be reconstructed into the 1/v vs. x graph. In this case the integral in the denominator of the expression for vav can be evaluated by graphical means.
Teacher's Note: Average speed is total distance over total time, not the mean of v over distance.
Exam Note: Plot 1/v against x; area gives time.
Question 1.11. A rod of length l leans by its upper end against a smooth vertical wall, while its other end leans against the floor. The end that leans against the wall moves uniformly downward. Will the other end move uniformly, too?
Solution. The speed with which the lower end of the rod moves, vx = dx/dt, can be written in the form vx = (dy/dt)(dx/dy). Since x = √(l2 − y2), we can write dx/dy = −y/√(l2 − y2), whence vx = −(y/√(l2 − y2))(dy/dt) = y|vy|/√(l2 − y2). Thus, the speed of the lower end gets smaller and smaller at y = 0. (So the lower end does not move uniformly.)
Teacher's Note: Differentiate x = √(l² − y²) with respect to time; vx depends on y.
Exam Note: Answer no; give vx as function of y.
Question 1.12. An object is thrown upward with an initial velocity v0. The drag on the object is assumed to be proportional to the velocity. What time will it take the object to move upward and what maximal altitude will it reach?
Solution. Since the drag is proportional to the velocity of the object, so is the acceleration caused by this force (with a minus sign). Hence, by Newton's second law, dv/dt = −g − rv, where r is the proportionality factor. Whence ∫v0v dv/(v + g/r) = −r ∫0t dt. Integration yields v = (v0 + g/r) e−rt − g/r. (1.12.1) For v = 0 this yields tm = (1/r) ln(1 + rv0/g). (1.12.2) To find the maximal altitude, we rewrite (1.12.1) in the form dh/dt = (v0 + g/r) e−rt − g/r. (1.12.3) Integrating this equation up to t, we find that h = (v0 + g/r)(1/r)(1 − e−rt) − (g/r) t. (1.12.4) Bearing in mind that at the point of greatest ascent v = dh/dt = 0 and combining this result with (1.12.3), we get (v0 + g/r) e−rtm = g/r. (1.12.5) Combining (1.12.4) with (1.12.5) yields h = (v0 − g tm)/r. Substituting tm from (1.12.2), we arrive at the final result h = (1/r)[v0 − (g/r) ln(1 + rv0/g)]. Corrected: the book prints ln(1 − rv0/g) in this last line; the correct sign is plus, as in (1.12.2). When drag is extremely low, rv0/g ≪ 1, we can employ the expansion ln(1 + rv0/g) ≈ rv0/g − (1/2)(rv0/g)2. This results in the well-known formula h = v02/2g. (The v-t curve is a decaying exponential that crosses zero at tm and tends to −g/r; the part below the t axis is the descent, where the speed approaches the value at which drag balances gravity.)
Teacher's Note: Write dv/dt = −g − rv and integrate; set v = 0 for the time to top.
Exam Note: Final h needs ln(1 + rv0/g); check low-drag limit.
Question 1.13. At a certain moment in time the angle between the velocity vector v of a material particle and the acceleration vector w of that particle is θ. What will be the motion of the particle at this moment for different θ's (Fig. 1.13 (a) to (d)): rectilinear or curvilinear, accelerated or uniform or decelerated?
Solution. The acceleration vector can be decomposed into two components, the tangential acceleration wt, which is directed along the same straight line as the velocity of the particle, and the normal acceleration wn, which is perpendicular to the velocity. For instance, for θ > 90° (Figure (a)) the tangential acceleration is directed opposite to the particle's velocity and the motion in this case is decelerated, w < 0. The presence of a nonzero normal acceleration suggests that the motion is curvilinear. The situation for the other cases is as follows: for θ < 90° (Figure (b)) the motion is curvilinear and accelerated, for θ = 90° (Figure (c)) the motion is curvilinear and uniform, and for θ = 180° (Figure (d)) the motion is rectilinear and decelerated, w < 0. Of course, characterizing the motion by the angle between the velocity v and the acceleration w is meaningful only for a definite moment in time. Subsequent motion may change this characteristic.
Teacher's Note: Resolve w along and perpendicular to v: tangential part changes speed, normal part turns direction.
Exam Note: Cover all four angles; speed change needs cosθ.
Question 1.14. A particle is moving along an expanding spiral in such a manner that the particle's normal acceleration remains constant. How will the linear and angular velocities change in the process?
Solution. The normal acceleration is wn = v2/R = ω2R, whence the linear velocity grows in proportion to the square root of the curvature radius of the spiral, while the angular velocity decreases by the same law (inversely as the square root of R).
Teacher's Note: Fix v²/R = ω²R; then v ∝ √R and ω ∝ 1/√R.
Exam Note: State both proportionalities with correct direction.
Question 1.15. A particle is moving in a circular orbit with a constant tangential acceleration. After a certain time t' has elapsed after the beginning of motion, the angle between the total acceleration w and the direction along the radius R becomes equal to 45°. What is the angular acceleration of the particle?
Solution. When the angle between the total acceleration and the radius becomes equal to 45°, the normal acceleration becomes equal to the tangential acceleration. Since wn = ω2R and wt = εR, we have ω2 = ε, and since ω = εt, we have ε2t2 = ε, with the result that ε = 1/t2 (t = t').
Teacher's Note: At 45 degrees wn = wt; start from rest so ω = εt.
Exam Note: Equate components, substitute ω = εt.
Question 1.16. An object is thrown at an angle α to the horizontal (0° < α < 90°) with a velocity v0. How do the normal acceleration wn and the tangential acceleration wt vary in the process of ascent if the drag is ignored?
Solution. The acceleration with which the object moves is the acceleration of gravity, which at all points of the trajectory is directed vertically downward. From the figure that accompanies the problem we see that as the object ascends the tangential acceleration decreases while the normal acceleration grows. At the highest possible point the tangential acceleration is zero while the normal acceleration is equal to the acceleration of gravity.
Teacher's Note: Resolve g along the changing tangent; the angle between g and velocity approaches 90 degrees at the top.
Exam Note: wt falls to 0, wn rises to g.
Question 1.17. At the foot of a hill a certain velocity is imparted to a sled, as a result of which the sled moves up the hill to a point A and then down the hill. What are the directions of the normal and tangential components of the acceleration at point A?
Solution. Since at point A the sled's velocity is zero, so is the normal acceleration wn = v2/R. The tangential acceleration is directed down the hill along the tangent to the surface of the hill. The figure accompanying the answer shows the forces that act on the sled. These are the force of gravity mg and the reaction force N exerted by the surface of the hill. The resultant F is directed downward along the hill. According to Newton's second law, the acceleration vector points in the same direction as the resultant. If there is friction, the resultant vector does not change direction but becomes somewhat shorter, with the result that the tangential acceleration becomes smaller, too.
Teacher's Note: At the turning point v = 0, so v²/R = 0; only the tangential part remains.
Exam Note: Normal part zero; tangential down the slope.
Question 1.18. An object moves without friction along a concave surface. What are the directions of the normal and tangential components of the acceleration at the lowest possible point?
Solution. The acceleration vector points in the direction of the resultant of the forces acting on the object. At the lowest possible point only the force of gravity and the reaction force act on the body, provided that there is no friction. This means that at this point the object experiences no tangential acceleration. Since the object is moving along a curvilinear trajectory with a certain velocity, there is a normal acceleration, which is directed toward the center of curvature of the trajectory. This acceleration is generated by the difference between the reaction force exerted by the surface and the force of gravity.
Teacher's Note: At the bottom, forces are vertical, so no tangential acceleration; N − mg supplies the centripetal force.
Exam Note: Tangential is zero; normal points upward to centre.
Question 1.19. A stunt rider on a unicycle is riding around the arena of a circus in a circle of radius R. The radius of the wheel of the unicycle is r and the angular velocity with which the wheel rotates is ω. What is the angular acceleration of the wheel? (Ignore the fact that the wheel axis is inclined.)
Solution. In the course of time Δt the angular velocity vector will vary from ω1 to ω2 without changing its length. The direction of the vector will change by an angle of Δφ. This angle is equal, on the one hand, to |Δω|/ω and, on the other, to ΔS/R, where ΔS stands for the displacement of the center of the wheel (it is assumed that Δφ ≪ 1 rad). This displacement is equal to ΩRΔt, where Ω is the angular velocity of the center of the wheel about the centre of the arena. Thus, |Δω|/ω = ΩRΔt/R and ε = limΔt→0 Δω/Δt = ωΩ. When the wheel is rotating, the point at which it touches the arena will shift in the course of Δt by a distance of rωΔt on the wheel and by RΩΔt on the arena. Hence, ω and Ω are linked by the following formula: ωr = ΩR, whence ε = ω2 r/R.
Teacher's Note: Only the direction of the angular velocity vector turns; rolling without slipping gives ωr = ΩR.
Exam Note: Use ε = ωΩ and Ω = ωr/R.
Question 1.20. A liquid has been poured into a cylindrical vessel of mass M (the mass of the vessel bottom can be ignored) and height H. The linear density of the liquid, that is, the ratio of the mass of the liquid column to its height, is δ. What is the height x of the column of liquid at which the common center of gravity of the liquid plus the vessel is in the lowest position?
Solution. The height of the center of mass of the vessel with the liquid is determined by the formula hc = (M(H/2) + m(x/2))/(M + m), (1.20.1) where m is the mass of the liquid. We rewrite (1.20.1) by replacing the mass of the liquid with δx: hc = (1/2)(MH + δx2)/(M + δx). (1.20.2) Nullifying the derivative of h with respect to x, dhc/dx = (1/2)(2δx(M + δx) − δ(MH + δx2))/(M + δx)2 = 0, we get x = ±√(M2/δ2 + MH/δ) − M/δ. (1.20.3) Of course, only the positive value of the root has physical meaning. Substituting this value into (1.20.2), we will find the position of the center of mass. After elementary transformations we get hc = √(M2/δ2 + MH/δ) − M/δ. We have found that the position of the center of mass coincides with the level of the liquid. Here are some particular cases: (1) δH = M (the liquid filling the vessel completely has a mass equal to the mass of the vessel). Then hc = x = H(√2 − 1) ≈ 0.41H. (2) δH ≪ M. Let us transform (1.20.3) to the form x = (M/δ)(√(1 + δH/M) − 1). The fraction in the radicand is considerably less than unity. Expanding (1 + δH/M)1/2 in a series and retaining only three terms, we get x ≈ (M/δ)(1 + δH/2M − δ2H2/8M2 − 1), or hc = x ≈ (H/2)(1 − δH/4M). The level of the liquid is below the middle of the vessel by an insignificant distance. (3) δH ≫ M. Let us transform (1.20.3) to the form x = H(√(M2/δ2H2 + M/δH) − M/δH). Bearing in mind that (M/δH)1/2 ≫ M/δH, we can assume that the expression inside the parentheses in the above formula is simply (M/δH)1/2, whence hc = x ≈ H(M/δH)1/2. The level of the liquid is above the bottom of the vessel by an insignificant distance.
Teacher's Note: The centre of mass is lowest exactly when it lies at the liquid surface; minimise hc(x).
Exam Note: Differentiate hc, keep positive root, check limits.
Question 1.21. A cone-shaped funnel is being rotated with constant angular velocity ω. An object is placed on the inner wall of the funnel. The object can freely move along the generatrix of the cone, but during the motion of the funnel the body is in a state of equilibrium. Is this equilibrium stable or unstable?
Solution. For the object to be in a state of equilibrium in relation to the wall of the funnel the resultant of the forces acting on the object must impart to the object together with the funnel an acceleration. These forces are the force of gravity and the reaction force exerted by the funnel. Since the force of gravity is constant in this problem and the resultant must be directed horizontally, the direction and magnitude of the reaction force are determined uniquely. But the latter has a different value at different distances from the funnel axis. At a constant angular velocity of the funnel, the greater the radius of rotation the greater the reaction force. For this reason (see the figure accompanying the answer), as the object moves farther from the funnel axis, the force of gravity and the reaction force acquires a component directed upward, while as the object moves closer to the axis, the resultant acquires a component directed downward. In the first case the object tends to move away from the axis still farther and rises, while in the second case it tends to move toward the axis and lowers. Thus, the state of equilibrium is unstable.
Teacher's Note: Displace the object slightly: the needed centripetal force changes with radius, pushing it further away.
Exam Note: Answer unstable; justify with small displacement.
Question 1.22. A vessel filled with water is moving horizontally with constant acceleration w. What shape will the surface of the liquid have?
Solution. It is convenient to think of the vessel with water as a noninertial system. In this case, there acts on each particle of water, in addition to the force of gravity, a force of inertia equal to the product of the particle's mass by the acceleration taken with the minus sign. The surface of water is a plane perpendicular to the vector of the resultant of these two forces. The slope of this surface in relation to the horizontal plane is tan α = w/g.
Teacher's Note: In the vessel's frame add inertial force −mw; the surface is perpendicular to the net of that and mg.
Exam Note: Plane inclined with tanα = w/g.
Question 1.23. A liquid has been poured into a cylindrical vessel. What shape will the surface of the liquid have if the vessel is rotated uniformly about its axis with an angular velocity ω?
Solution. Just like in the answer to the previous problem, we can assume the vessel with the liquid to be a noninertial system, in which a force of inertia equal to −mw = −mω2x acts on every particle of mass m. The resultant of this force and the force of gravity is perpendicular to the surface of the liquid. The derivative dy/dx, equal to the slope of the line tangent to the surface at a given point, is dy/dx = tan α = mω2x/(mg). Integrating, we find that y = (ω2/2g) x2. The surface of the liquid is shaped in the form of a paraboloid of revolution.
Teacher's Note: Slope at radius x is ω²x/g; integrate once to get a parabola.
Exam Note: State y = ω²x²/2g, paraboloid of revolution.
Question 1.24. A piece of cork has been attached to the bottom of a cylindrical vessel that has been filled with water and is rotating about the vertical axis with a constant angular velocity ω. At some moment the cork gets free and comes to the surface. What is the trajectory along which the cork moves to the surface: does it approach the wall or the axis or does it move vertically upward?
Solution. Just like in the answers to Problems 1.22 and 1.23, the vessel can be assumed to be a noninertial system. In such a system, every mass element, say, an element of water whose volume is equal to the volume of the piece of cork, is in a state of equilibrium due to three forces: the force of pressure of the surrounding water, the force of gravity, and the force of inertia, which is equal to the product of the element's mass by the normal acceleration of that element taken with the minus sign (Figure (a)). There are also three forces acting on the piece of cork that replaces the element of water: the force of pressure of the surrounding water is the same but the forces of gravity and inertia are lower. As Figure (b) shows, the net force (the difference between the force of pressure and the forces of gravity and inertia) make the cork rise to the surface and, at the same time, move toward the axis of the vessel. A similar line of reasoning forces us to conclude that an object with a density greater than the density of water, when immersed into a rotating vessel with water, will sink and, in the process, move toward the wall of the vessel.
Teacher's Note: Pressure gradient points toward the wall; the light cork is pushed the opposite way, toward the axis.
Exam Note: Say it rises and moves toward the axis.
Question 1.25. A force acting on a material particle of mass m first grows to a maximum value Fm and then decreases to zero. The force varies with time according to a linear law (a triangular F-t graph), and the total time of motion is tm. What will be the velocity of the particle by the end of this time interval if the initial velocity is zero?
Solution. According to Newton's second law, ∫0t F dt = Δ(mv). In the case at hand, ∫0t F dt = Fmt/2 (the area of the triangle, with t = tm), whence v = Fmtm/2m.
Teacher's Note: Impulse equals the area under the F-t graph; a triangle gives half base times height.
Exam Note: Area of triangle, divide by m.
Question 1.26. Along which of the two trajectories, the horizontal line ac'b or the broken line consisting of two straight segments (ac and cb), will the work performed by a force in displacing an object be greater if the friction is the same for all three straight segments?
Solution. The work performed along ac' is A1 = ac' mgk. The work performed against the forces of friction on the inclined segment ac is A2 = ac mgk cos α = (ac'/cos α) mgk cos α = ac' mgk. We see that the two quantities coincide, and so, obviously, do the similar quantities for c'b and cb. The change in the potential energy about ac'b and acb is zero. Thus, the work performed against the forces of friction along ac'b and that performed against the forces of friction along acb coincide.
Teacher's Note: Friction work on a slope is μmg cosα times slant length, which equals μmg times horizontal projection.
Exam Note: Work is equal along both paths.
Question 1.27. An object of mass m is sliding down a hill of arbitrary shape and, after traveling a certain horizontal path, stops because of friction. The friction coefficient may be different for different segments of the entire path but it is independent of the velocity and direction of motion. Find the work that a force must perform to return the object to its initial position along the same path.
Solution. The initial potential energy of the object with respect to the bottom of the hill, mgh, has been used up for work against the force of friction. In returning the body to its initial position, the force performs the same work and, in addition, imparts to the object the initial potential energy. As a result, the total work will be 2mgh.
Teacher's Note: Friction work is the same in both directions, mgh; add the potential energy gained, mgh.
Exam Note: Total work = 2mgh; explain the two parts.
Question 1.28. The dependence of the potential energy of an object on its position is given by the equation W = ax2 (a parabola). What is the law by which the force acting on the object varies?
Solution. The work performed on an elementary segment of displacement is equal to the decrease in potential energy: dA = −dW. The same work can be represented as the product of force by displacement: dA = Fxdx. Hence Fx = −dW/dx = −2ax. Forces known as quasielastic also obey this law.
Teacher's Note: Force is minus the gradient of potential energy; a parabola gives a linear restoring force.
Exam Note: F = −dW/dx; mention Hooke-like force.
Question 1.29. An object whose density is ρob falls from a certain height into a liquid whose density is ρliq. In the figure the potential energy W of the object is plotted along the vertical axis and the position of the object (its altitude) is plotted along the horizontal axis. The potential energy of the object at the level of the liquid is taken zero and the positive direction of the vertical axis (the W axis) is the one pointing upward from the liquid's surface. Determine which of the five straight lines, 1-5, corresponds to an object with the highest density and which to an object with the lowest density. Is there a straight line among these five for which ρob = (1/2)ρliq? The arrows on the straight lines point in the direction of motion of the object.
Solution. When the object is immersed in the liquid, two forces act on it: the force of gravity and Archimedes' force. If V is the volume of the object, the resultant of these two forces is F = V(ρob − ρliq)g. For ρob > ρliq, as the object is immersed in the liquid, its potential energy continues to fall below zero, but slower than it would in air. The rate of this decrease is the higher the greater the value of ρob. Straight line 1 in the figure accompanying the problem corresponds to an object with the highest density (sinking in a liquid). When ρob = ρliq, the potential energy remains constant (straight line 2 coinciding with the x axis). If ρob < ρliq, the potential energy of the object begins to increase when the object sinks into the liquid (straight lines 3, 4, 5), and the rate of this increase is the higher the lower the value of ρob; so the lowest density corresponds to line 5. The potential energy, while growing, cannot exceed the initial potential energy of the object in air (the dashed horizontal line), and the object can attain this level only when the medium exerts no drag on it. If this is the case, the object will sink to a certain level in the liquid, stop, and then return to the surface with the same speed at the surface as it had when it entered the liquid. Once out of the liquid, the object will rise to the height determined by the initial potential energy. After this it drops back into the liquid, and so on. Of course, under real conditions the drag exerted by the medium will slow down the object, and the greater the viscosity of the liquid the faster this happens. If the density of the material of the object is one-half the density of the liquid, ρob = (1/2)ρliq, then F = Vρobg. In this case the difference between Archimedes' force and the force of gravity is equal (in absolute value) to the latter but is directed in opposition to the force of gravity. The slope of the straight line must be the same as that of the straight line that represents the variation of the potential energy of a falling object. Straight line 4 has such a slope.
Teacher's Note: Net force in liquid is V(ρob − ρliq)g, and the slope of W equals minus that force.
Exam Note: Highest density line 1, lowest line 5, half density line 4.
Question 1.30. The dependence of the potential energy W of the interaction between two objects on the distance r separating them is shown in the figure (points 1 to 5 marked on the curve). What will be the distances between the objects that correspond to equilibrium positions? At what distance will the equilibrium be stable? (Answer the same question for unstable equilibrium.) What segments of the curve correspond to a repulsive force and what segments, to an attractive force?
Solution. The formula that links the force acting on an object with the potential energy of the object, Fr = −dW/dr, shows that equilibrium, which occurs when the force is zero, sets in when dW/dr = 0. There are two such points on the curve, point 2 and point 4. Since when the object moves away from point 2 its potential energy increases while when it moves away from point 4 its potential energy decreases, at point 2 equilibrium is stable and at point 4 it is unstable. The fact that a system always tends to a state in which its potential energy is minimal implies that repulsive forces act on the 1-2 and 4-5 segments and an attractive force acts on the 4-2 segment (that is, between points 2 and 4).
Teacher's Note: Equilibrium where dW/dr = 0; a minimum of W is stable, a maximum is unstable.
Exam Note: Identify minimum and maximum points on the curve.
Question 1.31. A load of mass m2 is hanging from a string. A bullet flying horizontally hits the load. Three cases are possible here, namely, (1) the bullet pierces the load and, retaining a fraction of its velocity, continues its flight, (2) the bullet gets stuck in the load, and (3) the bullet recoils from the load. In which of these three cases will the load be deflected by an angle α with the greatest magnitude and in which will it be deflected by an angle with the smallest magnitude?
Solution. Momentum conservation for the given problem can be written thus: m1v0 = m1u1 + m2u2, (1.31.1) where m1 is the bullet's mass, m2 the load's mass, v0 the initial velocity of the bullet, u1 the final velocity of the bullet, and u2 the velocity acquired by the load as a result of the collision. From (1.31.1) it follows that u2 = m1(v0 − u1)/m2. (1.31.2) If the bullet flies through the load, after it has left the load it has a velocity that is surely greater than u2. We write u1 = u2 + V. Substituting this expression into (1.31.1), we get u2 = m1(v0 − V)/(m1 + m2). (1.31.3) If the bullet gets stuck in the load, then u1 = u2 and, hence, u2 = m1v0/(m1 + m2). (1.31.4) Finally, if the bullet recoils from the load, the velocity it acquires after collision, u1, is negative and (1.31.2) can be written in the form u2 = m1(v0 + |u1|)/m2. (1.31.5) A comparison of (1.31.3), (1.31.4), and (1.31.5) shows that the load acquires the highest velocity (and the greatest deflection, as a result) when the bullet recoils from it, while the lowest velocity is acquired when the bullet pierces the load.
Teacher's Note: The load's speed after impact decides the angle; compare the three momentum equations.
Exam Note: Greatest: recoil; smallest: pierces; stuck lies between.
Question 1.32. Two spheres of equal mass collide, with the collision being absolutely elastic but not central. Prove that in this case the angle between the velocities after collision must be 90°.
Solution. For the sake of convenience we employ a coordinate system in which the velocity of one of the spheres prior to collision is zero. According to the energy conservation law, in the case of an absolutely elastic collision we have m1v02/2 = m1u12/2 + m2u22/2, where m1 and m2 are the masses of the spheres, v0 is the velocity of the first sphere prior to collision, and u1 and u2 are the velocities of the spheres after collision. Since the masses of the spheres are the same, we can write v02 = u12 + u22. The velocity vector v0 is the hypotenuse of a right triangle whose sides are the velocity vectors u1 and u2, and hence the angle between u1 and u2 is 90°. (Momentum conservation gives v0 = u1 + u2 as vectors, which forms the triangle.)
Teacher's Note: Momentum makes v0 = u1 + u2; energy makes v0² = u1² + u2²: Pythagoras.
Exam Note: Equal masses: vector triangle plus energy gives 90 degrees.
Question 1.33. A sphere of mass m1 impinges with a velocity v0 on a sphere of mass m2 that is at rest, with m1 > m2. The collision is absolutely elastic but not central. By what maximal angle θ will the impinging sphere be deflected?
Solution. Let u1 and u2 be the final velocities of the impinging sphere and the one that was at rest prior to collision, respectively, and θ is the angle between u1 and v0 (and φ the angle of u2 to v0). The equations that express the laws of conservation of energy and momentum (for each projection) have the following form: m1v02/2 = m1u12/2 + m2u22/2, (1.33.1) m1v0 = m1u1 cos θ + m2u2 cos φ, (1.33.2) m1u1 sin θ + m2u2 sin φ = 0. (1.33.3) If m1, m2, and v0 are fixed, then u1, u2, θ, and φ are linked through three equations. For this reason two of the four variables can be excluded and the variable θ can be expressed in terms of the third remaining variable, say, u1. Taking m1u1 cos θ to the left-hand side of Eq. (1.33.2), squaring the result and Eq. (1.33.3), and adding the two squares, we get m12(v02 − 2u1v0 cos θ + u12) = m22u22. Replacing u2 with its value obtained from (1.33.1) and carrying out the necessary transformations, we arrive at a quadratic equation for u1, namely, u12 − 2(m1/(m1 + m2)) v0 cos θ · u1 + ((m1 − m2)/(m1 + m2)) v02 = 0, (1.33.4) whose solution has the form u1 = (m1/(m1 + m2)) (cos θ ± √((m2/m1)2 − sin2 θ)) v0. (1.33.5) This equation shows that the maximal angle θ is determined by the condition sin θm = m2/m1. (1.33.6) For values of θ smaller than θm two cases are possible, since two distinct values of u1 correspond to one value of θ. For example, for m1/m2 = 3 and sin θ = 0.2, the velocity u1 may have two values, 0.93v0 and 0.53v0. The first collision is commonly known as soft, while the second is known as hard. The extreme case of soft collision is the grazing collision (or even the case where one sphere misses the other), while the extreme case of hard collision is the head-on collision, after which the velocity of the impinging sphere becomes u1 = ((m1 − m2)/(m1 + m2)) v0. Condition (1.33.6) can be obtained in another manner as well. For instance, if we express cos θ via (1.33.4), namely, cos θ = (1/2m1)[(m1 + m2) u1/v0 + (m1 − m2) v0/u1], and nullify the derivative of cos θ with respect to u1, we can find the minimal value of cos θ or the maximal value of sin θ. The motion of the impinging sphere can also be considered using the system of coordinates linked with the center of mass of the two spheres. If in the laboratory system the coordinates of the spheres are x1 and x2, then the coordinate of the center of mass is x = (m1x1 + m2x2)/(m1 + m2), while the velocity of the center of mass is vc = (m1/(m1 + m2)) v0. Correspondingly, the velocity of the impinging sphere in this system prior to collision is v0' = v0 − vc = (m2/(m1 + m2)) v0. As a result of the collision the vector v0' retains its length but turns through a certain angle depending on the distance between the center of the second sphere and the direction of flight of the impinging sphere prior to collision. The velocity u1 is equal to the sum of v0' and vc. The momentum vectors of both spheres are shown in the figure for three cases: soft collision (Figure (a)) and hard collision (Figure (b)) for m1/m2 = 3 and sin θ = 0.2 and the case with sin θ = m2/m1 = 1/3 (Figure (c)). The velocity of the impinging sphere after collision is u1 = (m1v0/(m1 + m2)) cos θ = 0.707v0. The above-discussed problem is important for the theory of atomic collisions. For instance, if a potassium ion impinges on a helium atom (m1/m2 = 10), as a result of an elastic collision the ion may be deflected by an angle no greater than 5.7°.
Teacher's Note: Heavier ball cannot rebound: u1 must be real, so the square root bounds the angle.
Exam Note: State sinθmax = m2/m1; show both energy and momentum used.
Question 1.34. Two spheres of equal mass are moving at right angles with velocities that are equal in magnitude. At the moment of collision the velocity vector of sphere 1 is directed along the straight line connecting the centers of the spheres. The collision is absolutely elastic. Plot the velocity vectors before and after collision in different coordinate systems: (1) in the laboratory system (in this system the velocities of the spheres are those specified above), (2) in the coordinate system connected with the center of mass of the two spheres, and (3) and (4) in the coordinate systems linked to each of the spheres.
Solution. We will consider each case in the order that it appears in the problem. (1) The directions of the velocities of the spheres in the laboratory system are shown in the figure accompanying the problem (Figure (a)). If at the moment of collision we project the velocities of the spheres and the corresponding momenta on two axes one of which coincides with the direction of the initial velocity of sphere 1 and the other with that of the initial velocity of sphere 2, then in the first of these two directions the spheres exchange the respective projections of the velocities, just like in a head-on elastic collision. Sphere 1 stops in the process. Since in the collision the force acts along the straight line connecting the centers of the spheres, the initial velocity of sphere 2 is conserved, with the velocity of sphere 1, which is perpendicular to the initial velocity of sphere 2, added to it. As a result the velocity of sphere 2 becomes equal to the geometric sum of the initial velocities of both spheres, that is, v0√2 (Figure (a)). (2) To determine the velocities of the spheres in the center-of-mass system, we decompose the velocity vector of each sphere into two perpendicular and equal components, v1a and v1b and v2a and v2b. The components v1a and v2a are equal in magnitude and point in the same direction. Obviously, the common center of mass moves in the same direction and with the same velocity, vc, with respect to the laboratory system. Therefore, in the system linked with the center of mass there are only the velocities v1b and v2b. The velocities of the spheres after collision can be obtained if we subtract vc from the velocities of the spheres in the laboratory system. The other velocities are shown in Figure (b). (3) In the system linked with sphere 1, the sphere, obviously, remains at rest during the entire collision process. The velocity of sphere 2 in this system can be obtained by subtracting geometrically the initial velocity of sphere 1 from the velocity of sphere 2 in the laboratory system. Since the velocity of sphere 1 after collision is equal, in the laboratory system, to zero and is also zero in the system linked with sphere 1, the velocity of sphere 2 in this system after collision is the same as in the laboratory system (Figure (c)). (4) In the system linked with sphere 2, the velocity of sphere 1 is obtained by subtracting geometrically the initial velocity of sphere 2 from the velocity of sphere 1. After collision the velocity of sphere 1 is equal, in absolute value, to the final velocity of sphere 2 in the laboratory system and points in the opposite direction (Figure (d)). In conclusion we would like to bring the reader's attention to the fact that the angular momenta of the spheres with respect to the center of mass remain constant during the entire collision process. In collision, the center of mass is the point where the spheres touch and the angular momentum of sphere 1 is zero and remains such after collision. The angular momentum of sphere 2 is equal, prior to collision, to the product of momentum mv by the arm R. After collision the momentum of sphere 2 becomes mv√2, but the arm is now R/√2, so the product is the same and the angular momentum is conserved. Of course, since the system consisting of the spheres is isolated, the angular momentum is conserved in the entire process of motion. (The vector diagrams of Fig. 1.34 are not redrawn here; they are described in the text above.)
Teacher's Note: Impact force acts along the line of centres, so only that velocity component is exchanged.
Exam Note: Say sphere 1 stops; sphere 2 moves at v0√2.
Question 1.35. The centers of the spheres 1, 2, and 3 lie on a single straight line. Sphere 1 is moving with an (initial) velocity v1 directed along this line and hits sphere 2. Sphere 2, acquiring after collision a velocity v2, hits sphere 3. Both collisions are absolutely elastic. What must be the mass of sphere 2 for the sphere 3 to acquire maximum velocity (the masses m1 and m3 of spheres 1 and 3 are known)?
Solution. After collision, sphere 2 acquires the velocity u2 = 2m1v1/(m1 + m2). (1.35.1) Sphere 3 acquires the following velocity after collision: u3 = 2m2u2/(m2 + m3). Substituting the value of u2 from (1.35.1), we get u3 = 4m1m2v1/((m1 + m2)(m2 + m3)). The extremal value of u3 can be found by nullifying the derivative of u3 with respect to m2: du3/dm2 = 4m1v1(m1m3 − m22)/[(m1 + m2)(m2 + m3)]2 = 0. From this it follows that m2 = √(m1m3). We can easily see that this value corresponds to the maximum of u3. Here are some particular cases. (1) m1 ≫ m3. In this case u3 ≈ 4v1 (Corrected, exactly: u3 = 4m1v1/(√m1 + √m3)2; the book's intermediate approximation 4m1v1/(m1 + m3) is only the limiting form). If sphere 1 were to hit sphere 3 directly (without the intermediate sphere 2), the highest velocity of sphere 3 for m1 ≫ m3 would be roughly 2v1. In some fantastic projects of interplanetary flight it has been suggested that the spaceship be accelerated to the necessary speed through a series of collisions with intermediate objects whose masses must be calculated in the appropriate manner. (2) m1 = m3. In this case m2 = m1 = m3 and u3 = v1. (3) m1 ≪ m3. Assuming that m2 ≫ m1, we get u3 ≈ 4v1m1/m3. Here the velocity of sphere 3 is approximately double the velocity without an intermediate object, sphere 2.
Teacher's Note: Chain two elastic collisions, then maximise u3(m2); the best m2 is the geometric mean.
Exam Note: Give m2 = √(m1m3) after setting derivative to zero.
Question 1.36. A sphere of mass m1 moving with a velocity v0 hits a sphere of mass m2 that is at rest. The collision is absolutely elastic and central. The velocities of the spheres after collision are u1 and u2, respectively. What are the mass ratios for the following values of velocities: u1 = 0, u1 < 0, and u1 > 0?
Solution. The velocities of the spheres after collision are u1 = ((m1 − m2)/(m1 + m2)) v0, u2 = (2m1/(m1 + m2)) v0. Here are some particular cases. (1) u1 < 0 if m1 < m2. Since in this case 2m1 < m1 + m2, we have 0 < u2 < v0. (2) u1 = 0 if m1 = m2. Then u2 = v0. (3) u1 > 0 if m1 > m2. Then 2m1 > m1 + m2 and v0 < u2 < 2v0.
Teacher's Note: Elastic head-on formulas: the sign of u1 follows the sign of m1 − m2.
Exam Note: Equal masses: velocities exchange; lighter hitter rebounds.
Question 1.37. A device often used to illustrate the laws of uniformly accelerated motion is the Atwood machine. The machine consists of two loads of mass m1 and m2 attached to the ends of a limp but inextensible string. The string runs over a pulley. The acceleration with which the loads move is w = ((m1 − m2)/(m1 + m2)) g, whereas the angular acceleration of the pulley is ignored. Is the last assumption true for exact calculations?
Solution. The equations of motion for the loads and the pulley can be written as follows: m1w = m1g − T1, m2w = T2 − m2g, Jε = (T1 − T2)R, (1.37.1) where T1 is the force exerted by the left end of the string on the left load, T2 the force exerted by the right end of the string on the right load, J the moment of inertia of the pulley, w the acceleration of the loads, and ε is angular acceleration of the pulley. Dividing (1.37.1) by R, adding all the equations, and replacing ε with w/R, we arrive, after appropriate transformations, at w = ((m1 − m2)/(m1 + m2 + J/R2)) g. (1.37.2) Equation (1.37.2) shows that in exact calculations we must allow for the moment of inertia and the radius of the pulley. If the pulley is a homogeneous disk, then instead of J we can write mpR2/2, and Eq. (1.37.2) assumes the form w = ((m1 − m2)/(m1 + m2 + mp/2)) g. We see that in this case the radius of the pulley plays no role; what is important is only the mass of the pulley.
Teacher's Note: A real pulley needs torque to spin, so the tensions on both sides differ.
Exam Note: Answer no; give w with J/R² included.
Question 1.38. Strings are wound around a shaft and a sheave of equal mass, and a load is attached to the end of each string (the loads have equal mass). Which of the two loads will descend with a greater acceleration and which of the rotating objects, the shaft or the sheave, has a greater angular acceleration?
Solution. The equations of motion for the load-shaft or the load-sheave can be written as follows: mg − T = mw, TR = Jε, where m is the mass of each load, T the force exerted by the strings attached to the loads, R the radius of the shaft or sheave, J the moment of inertia of the shaft or sheave, and ε the angular acceleration of the shaft or sheave. Eliminating T from the equations and replacing ε with w/R and the moment of inertia of the shaft or sheave with MR2/2, we arrive, after simple transformations, at w = (m/(m + M/2)) g, from which it follows that the accelerations with which the two loads are lowered coincide. The angular acceleration is the greater the smaller the radius (ε = w/R), which means that the shaft has a greater angular acceleration than the sheave. Corrected: the book prints “the larger the radius” in this sentence, a slip, since ε = w/R grows as R decreases; its conclusion (the shaft has the greater ε) is right.
Teacher's Note: Same mass, same shape means same w; ε = w/R, so the smaller radius spins faster.
Exam Note: Loads equal acceleration; shaft has greater ε.
Question 1.39. A vacuum cleaner standing on the floor turns through a small angle when switched on and then stops. Why does this happen?
Solution. Prior to switch-on, the sum of the angular momenta of all the parts of the vacuum cleaner is zero. When the motor is switched on, a torque appears in the rotor of the motor, with the same torque (in absolute value) appearing in the stator and the casing of the vacuum cleaner is fixed to the stator. Due to the latter torque, the vacuum cleaner begins to turn, but this motion dies out very soon because of friction.
Teacher's Note: Internal torques come in equal and opposite pairs: rotor spins one way, casing recoils the other.
Exam Note: Cite angular momentum conservation and friction stopping the turn.
Question 1.40. A number of types of helicopters, among which are the Soviet-made “Mi” helicopters and the Westland Whirlwinds designed for use by Queen Elizabeth II, utilize one main rotor and a small vertical tail rotor. What is the function of this second rotor?
Solution. When the engine of the helicopter of this type is operating, two torques appear: one is applied to the main rotor and the other (equal in magnitude to the first) is applied to the fuselage of the copter. This second torque tends to turn the fuselage in the direction opposite to that of the main rotor. The vertical tail rotor creates a torque that cancels out the torque applied to the fuselage. In toy helicopters this second rotor is fixed and the helicopter rotates in flight in a direction opposite to that of the main rotor.
Teacher's Note: Reaction torque on the body would spin it opposite to the main rotor; the tail rotor cancels it.
Exam Note: Name reaction torque; tail rotor gives balancing torque.
Question 1.41. A rod whose lower end is sliding along the horizontal plane starts to topple from the vertical position. What will be the velocity of the upper end when this end hits the ground?
Solution. The rod is in rotational motion, and so its potential energy is transformed into the kinetic energy of rotation. If the mass of the rod is m and the length is l, we have mgl/2 = Jω2/2. Replacing ω with v/l and J with ml2/3, we get v = √(3gl).
Teacher's Note: Energy conservation: the centre of mass falls l/2; J = ml²/3 about the end.
Exam Note: Write mgl/2 = Jω²/2 and v = ωl.
Question 1.42. A thin rod of length 2R and mass m is standing (vertically) on a perfectly smooth floor. The state of equilibrium in which the rod is at rest is unstable, and the rod falls. Find the trajectories that the various points of the rod describe and the velocity with which the upper end of the rod hits the floor.
Solution. To determine the trajectories that the various points of the rod describe, we introduce a coordinate system whose origin lies at B, the lower point of the rod prior to falling, whose x axis points horizontally in the direction in which point B moves during motion, and whose y axis points upward, along the rod prior to motion. Since there are no forces that act on the rod in the horizontal direction, the rod's center of mass moves downward (from C to B). As Figure (a) shows, the coordinates of the points lying above the center of mass by a distance a are determined by the equations x = −a cos α, y = (R + a) sin α, while the coordinates of the points lying below the center of mass by a distance a are determined by the equations x = a cos α, y = (R − a) sin α. These equations imply that in the process of falling the rod (and that means all of its points except the center of mass) describes quarters of ellipses (Figure (b)) specified by the equations x2/a2 + y2/(R + a)2 = 1 (upper points), x2/a2 + y2/(R − a)2 = 1 (lower points). When the rod is falling, its motion can be considered as rotation about an instantaneous center, D. Therefore, the velocity of the upper point (A) can be determined just like in Problem 1.41, using the law of conservation of energy. The appropriate equations yield v = √(6gR).
Teacher's Note: No horizontal force, so the centre of mass falls straight down; other points trace ellipses.
Exam Note: Give ellipse equations and v = √(6gR) = √(3g l).
Question 1.43. A homogeneous rod AB is lying on a perfectly smooth floor. A bullet hits the rod and gets stuck in it. The direction of the bullet's initial velocity v0 is perpendicular to the rod, and the point where the bullet hits the rod lies at a distance x from the middle of the rod. The mass of the bullet is m and the mass of the rod is M. Will a velocity directed in opposition to v0 be imparted to end A at the first moment after the collision?
Solution. The velocity imparted to point A will be directed in opposition to v0 if the rod's linear velocity acquired as a result of rotation after the bullet has hit the rod is greater than the velocity of the center of mass of the rod. Moreover, for such a situation to occur, the distance x must not exceed one-half of the length of the rod (2R is the rod's length). According to the law of conservation of momentum, mv0 = m(v + ωx) + Mv. (1.43.1) Here we have allowed for the fact that the velocity of the bullet after the bullet has hit the rod is the sum of the velocity of the center of mass, v, and the velocity ωx which the point that is distant x from the center of mass acquires as a result of rotational motion with angular velocity ω. According to the law of conservation of angular momentum, mv0x = m(v + ωx)x + Jω, (1.43.2) where J is the moment of inertia of the rod about the center of mass, J = MR2/3. Multiplying (1.43.1) by x and subtracting the product from (1.43.2), we get ω = Mvx/J = 3vx/R2. The linear velocity of rotation acquired by point A (we denote this velocity by V) is V = ωR = 3vx/R. The ratio V/v is greater than unity if x > R/3. So the answer is yes, provided R/3 < x ≤ R.
Teacher's Note: Hit off-centre gives spin plus translation; end A moves backward if its spin speed exceeds v.
Exam Note: Solve momentum and angular momentum; condition x > R/3.
Question 1.44. The axis AB of a gyroscope is mounted in a frame that can rotate about the axis CD. This frame is mounted, via vertical supports CC' and DD', on a horizontal platform which, in turn, can rotate about the axis EF. At first the platform is at rest and the gyroscope is rotating in the direction designated by arrow 1. Then the platform begins to rotate in the direction designated by arrow 2. How will the gyroscope's axis change its position in space?
Solution. According to the right-hand screw rule, the vector of the angular velocity of the gyroscope is directed to the right in the figures accompanying the problem and the answer. The revolving platform applies a torque to the frame, and the vector of this torque is directed perpendicularly to the vector of the angular velocity of the gyroscope. This torque creates an angular acceleration ε, and under this acceleration the vector of angular velocity rotates in the direction shown by the arrow in the figure accompanying the answer. As a result the gyroscope's axis places itself vertically and the direction of rotation of the gyroscope coincides with the direction of rotation of the platform. If the direction of rotation of the gyroscope or the direction of rotation of the platform were to change, the gyroscope's axis would point in the opposite direction. In all cases the axis rotates in such a manner that the vector of angular velocity places itself in the direction coinciding with that of the vector of an external torque. This property of gyroscopes is used in navigation in gyrocompasses. The “platform” that applies a torque to the gyroscope is the earth in this case.
Teacher's Note: The spin vector turns towards the vector of the applied torque, which is how gyrocompasses work.
Exam Note: Axis turns to align spin with platform rotation.
Question 1.45. A top is spinning in the direction designated by the arrow in the figure. In what direction does the precession of the top occur?
Solution. The vector of the angular velocity of the top is directed upward along the top's axis (see the figure accompanying the answer). The force of gravity applied to the top at the top's center of mass creates a torque whose vector, being perpendicular to the vector of angular velocity, is directed away from the reader. This torque does not change the magnitude of the angular velocity but creates an angular acceleration and hence changes the direction of the vector of angular velocity, just like centripetal acceleration does not change the value of the velocity but does change the direction of the velocity vector, as a result of which the body to which the centripetal acceleration is applied moves along a circle. In the case at hand the direction of the angular acceleration is such that precession occurs counterclockwise (if one views the top from above).
Teacher's Note: Gravity's torque is horizontal and perpendicular to spin, so it turns the axis, not the spin speed.
Exam Note: Say counterclockwise viewed from above, per the figure.
Question 1.46. A shaft whose diameter is d and length is l is rotating without friction in bearings with an angular velocity ω0. A sleeve of height h and outer diameter D is fitted on the shaft (the materials of the sleeve and the shaft are the same). At first the sleeve is not connected with the shaft and is at rest. Then at some moment the sleeve is clamped to the shaft. What will be the common angular velocity of the shaft plus the sleeve?
Solution. Since no external forces act on the shaft-sleeve system, the total angular momentum of the system remains constant: Jshω0 = (Jsh + Jsl)ω. (1.46.1) The moment of inertia of the shaft is Jsh = ρ(πd4/32) l, where ρ is the density of the material of the shaft and sleeve. The moment of inertia of the sleeve is Jsl = ρ(π(D4 − d4)/32) h. From (1.46.1) it follows that ω0d4l = ω[(D4 − d4)h + d4l], whence ω = d4l/(d4(l − h) + D4h) ω0 = d4l/(d4l + (D4 − d4)h) ω0 = 1/(1 + (D4/d4 − 1)(h/l)) ω0.
Teacher's Note: No external torque, so Jω is conserved; solid cylinder J = ρπd⁴l/32.
Exam Note: Write Jsh and Jsl; equate angular momenta.
Question 1.47. A disk and a sphere roll off two inclined planes of the same altitude and length. Which of the two objects will get to the bottom of the respective plane first? How does the result depend on the masses and diameters of the disk and the sphere?
Solution. The potential energy of an object on the top of a hill, mgh, transforms into the kinetic energy of translational and rotational motion: mgh = mv2/2 + Jω2/2. Replacing ω with v/R, we get mgh = mv2/2 + Jv2/2R2. (1.47.1) The moments of inertia of the disk, Jd, and the sphere, Jsp, are Jd = mR2/2 and Jsp = (2/5)mR2, respectively, with R the radius of the disk or sphere. Substituting these values into (1.47.1) and dividing by m, we get gh = v2/2 + v2/4 = 0.75v2 (1.47.2) for the disk and gh = v2/2 + v2/5 = 0.7v2 (1.47.3) for the sphere. Since the left-hand sides of these equations are the same, the final velocity of the sphere is greater, and since the motion is uniformly accelerated, the sphere will get to the horizontal section earlier than the disk. Neither the masses nor the radii of the objects rolling down the inclined planes are present in (1.47.2) and (1.47.3), with the result that the time it takes the objects to roll down is independent of these quantities.
Teacher's Note: Compare energy shares: more kinetic energy going into spin means slower translation.
Exam Note: Sphere wins; mass and radius cancel out.
Question 1.48. A spacecraft is circling the earth E along an elliptical orbit. How must the velocity of the spacecraft at perigee P and apogee A be changed so that the spacecraft follows a circular orbit?
Solution. When the spacecraft goes into a circular orbit at the perigee, it will circle the earth along a low orbit during the second half of the orbit. For this reason the spacecraft's potential energy at the new apogee will be lower than at the old one and, hence, such a maneuver requires lower kinetic energy. This means that the spacecraft must lower its velocity. Similar reasoning shows that to go into a circular orbit at the apogee, the spacecraft must increase its velocity.
Teacher's Note: Circular orbit at perigee height is lower than the ellipse's far side, so speed must drop there.
Exam Note: Perigee: reduce speed; apogee: increase speed.
Question 1.49. Several artificial satellites of the same mass are circling the earth along circular orbits of different radii. How do the kinetic, potential, and total energies and angular momenta of the satellites depend on the radii of the orbits?
Solution. The kinetic energy of a satellite is determined by the value of the orbital (or satellite) velocity. According to Newton's second law and the law of universal gravitation, GMm/R2 = mv2/R, where M is the mass of the earth, m the mass of the satellite, v the velocity of the satellite, and G the gravitational constant. From this it follows that the kinetic energy Wkin = mv2/2 = GMm/2R is the smaller the higher the orbit of the satellite. The potential energy (we take it equal to zero at infinity) Wpot = −GMm/R is the greater the higher the orbit of the satellite. The same is true of the total energy: W = Wkin + Wpot = −GMm/2R. The angular momentum also increases as we move farther away from the earth and is equal to mvR = m√(GMR).
Teacher's Note: Orbital speed falls with radius, but potential and total energies rise (become less negative).
Exam Note: Give Wkin, Wpot, W, L as functions of R.
Question 1.50. Three orbital space stations are circling the earth along different orbits: one along a circular orbit and the other two along elliptical orbits whose major axes are equal to the diameter of the circular orbit. The masses of the stations are the same. Will the energies and angular momenta of the stations coincide or will they be different?
Solution. Let us consider an extremely elongated orbit. In this case the distance between the foci differs little from the length of the major axis. Therefore, the force acting on a space station near the apogee can be assumed to be roughly the same for all extremely elongated orbits. Under this force the space stations move with the same accelerations wc = v2/R, where R is the curvature radius of the trajectory, and v is the velocity at apogee. The smaller the radius of curvature, the smaller is the velocity of a space station, and the greater the elongation of the orbit, the smaller is the radius. Hence, the velocity and therefore the kinetic energy at apogee tend to zero and the space stations possess almost exclusively potential energy. Since the total energy of a space station remains constant in flight, at all other points on the orbit it is equal to the sum of the kinetic and potential energies. The potential energy of the interaction between the earth and the station (this energy is assumed to be zero at infinity) is Wpot = −GMm/a, where M is the mass of the earth, m the mass of the station, G the gravitational constant, and a the distance from the center of the earth to the station (this quantity is practically equal to the length of the major axis of the orbit). When circling the earth along a circular orbit whose radius R is approximately a/2, the station possesses potential energy Wpot = −2GMm/a. As shown in the solution to Problem 1.49, the kinetic energy of the station in this case is Wkin = GMm/a, while the total energy is W = −GMm/a, which means that it is the same as for an elliptical orbit. It is convenient to determine the angular momentum of a station when the station passes through the apogee: L = mva. For extremely elongated orbits, a is roughly the same for all orbits, but the greater the elongation of the orbit the smaller the velocity at apogee. Hence, the angular momentum at apogee is the smaller the greater the elongation of the orbit. But since the torque of the force of attraction to the earth is zero, the angular momentum must be the same at all points of the orbit. Hence, the energy of the station in a circular orbit and that of the station in an elliptical orbit coincide, while the angular momentum is the smaller the greater the elongation of the orbit.
Teacher's Note: Total energy depends only on the major axis; angular momentum depends on how elongated the orbit is.
Exam Note: Energies equal; angular momenta differ, smaller for elongated orbits.
Question 1.51. A spacecraft is circling the earth along a circular orbit and retains its orientation with respect to the earth. Is zero gravity inside the spacecraft absolute in this case?
Solution. The fact that the spacecraft retains its orientation with respect to the earth means that all points of the spacecraft move with the same angular velocity. Suppose that the point closest to the surface of the earth moves with the orbital (satellite) velocity according to the equation ω2R = GM/R2, (1.51.1) where R is the distance between this point and the center of the earth. The point of the spacecraft farthest from the earth moves with an acceleration ω2(R + D), where D is the distance between the two points. If we consider the spacecraft to be a noninertial system, we can assume that on an object of mass m placed at the point farthest from the earth there acts a force of inertia Fi = −mω2(R + D). At the same time, there is the force of gravity acting on this object: F = GMm/(R + D)2. The sum of these two forces plays the role of “weight” for the object, or numerically the reaction of the support exerted on the object: Fw = mω2(R + D) − GMm/(R + D)2. Bearing in mind that D ≪ R, we can replace (R + D)−2 with (1 − 2D/R)/R2. Thus Fw ≈ m[ω2R(1 + D/R) − (GM/R2)(1 − 2D/R)], and if we allow for (1.51.1), we get Fw ≈ GMm/R2 · 3D/R. Since GMm/R2 is equal, to a high accuracy, to the weight of the object on the surface of the earth, or mg, we get Fw = (3D/R) mg. This expression gives the “weight” of an object in the spacecraft at the point farthest from the earth. Assuming that D is 2.1 m and bearing in mind that R = 6300 km, we find that the “weight” of an astronaut whose mass is 70 kg is 6.9 × 10−4 N at the point within the spacecraft farthest from the earth. So zero gravity is not absolute: tidal effects leave a tiny residual weight.
Teacher's Note: Different points sit at different distances, so gravity and inertial force cancel exactly only at one point.
Exam Note: Answer no; give F = 3Dmg/R and the number.
Question 1.52. A comet flies into the solar system from remote outer space. The trajectory of the comet is a branch of a hyperbola. Can the comet become a satellite of the sun S if the interaction of the comet with the planets of the solar system is ignored?
Solution. The potential energy of the comet (equal to zero at infinity) is −GMm/r, where m is the comet's mass, M the mass of the sun, and r the distance between the sun and the comet. As the comet approaches the sun, this energy decreases, which means that the kinetic energy increases, with mv2/2 − GMm/r remaining zero (it is assumed that the initial kinetic energy of the comet in far-away regions of space is negligible). The angular momentum of the comet is also conserved, since the torque produced by central forces is always zero. If we take two points, one at the aphelion of the presumable closed trajectory and the other placed at the same distance from the sun on the second branch of the parabola, then the potential energies at these points must coincide (since the distances coincide), which means that the kinetic energies at these points coincide and so do the velocities. But, as follows from the figure accompanying the problem, the angular momentum at the aphelion must be higher than on the branches of the parabola, which is impossible. At the same time, at symmetrical points both the kinetic energies and the potential energies are the same, and the same is true of the angular momenta. The above reasoning is true for both closed orbits (ellipses and circles) and open orbits (parabolas and hyperbolas) of heavenly bodies moving in the field of a single attraction center. The fact that both the energy conservation law and the angular momentum conservation law must be satisfied makes it impossible for a central force to change the nature of a trajectory. So the answer is no: the comet cannot become a satellite.
Teacher's Note: Energy and angular momentum are conserved in a central field, so an open orbit stays open.
Exam Note: Answer no; cite both conservation laws.
Question 1.53. What shape will a round disk have if viewed from a system of coordinates with respect to which the disk is moving with a certain velocity directed along the diameter of the disk?
Solution. If D0 is the diameter of the disk at rest, then in the system of coordinates with respect to which the disk is in motion the diameter in the direction of the velocity will be D = D0√(1 − v2/c2) = D0√(1 − β2). The same is true of the ratio of the halves of the chord passing at an altitude y from the center: x = x0√(1 − β2). Since x02 = R2 − y2, we have x2 = (R2 − y2)(1 − β2), whence x2/(R2(1 − β2)) + y2/R2 = 1. The moving disk appears to be an ellipse with semi-axes R and R√(1 − β2).
Teacher's Note: Length contraction acts only along the motion; the perpendicular direction is unchanged.
Exam Note: Ellipse, semi-axes R and R√(1 − β²).
Question 1.54. An isosceles right triangle is moving with respect to a system of coordinates with a velocity v directed along the hypotenuse. When viewed from this system, the triangle appears to be an equilateral triangle. Find the velocity with which the triangle is moving with respect to this system.
Solution. The velocity of the triangle is directed perpendicularly to the altitude, with the result that the length of the altitude is independent of the velocity. The hypotenuse is equal to twice the altitude (l0 = 2h), while the length of a side of the equilateral triangle is l = 2h tan 30°. Thus, for the moving triangle we have l = l0√(1 − β2) and (2√3/3) h = 2h√(1 − β2). Hence β = 0.816, that is, v = 0.816c.
Teacher's Note: Only the hypotenuse, along the motion, contracts; the altitude h stays fixed.
Exam Note: Equate 2h tan30° to 2h√(1 − β²).
Question 1.55. The various relationships that exist between time intervals, coordinates, and velocities in the special theory of relativity are conveniently illustrated via a system of coordinates in which on the axes we lay off either distance and time multiplied by the speed of light or time and distance divided by the speed of light. Curves that represent motion in such systems are known as world lines. Various world lines are shown in the figure (a to e) in the x/c vs. t coordinates. What does each line represent? Is there a line that contradicts the main principles of relativity theory?
Solution. As Figure (a) accompanying this problem shows, the world line passing through the origin at an angle θ to the x/c axis represents the motion of an object moving away from the observer (placed at the origin) with a velocity v = c cot θ. The other figures correspond to the following cases: (b) an object moving toward the observer with a velocity v = c cot θ, (c) motion with the speed of light, and (d) an object is at rest at a certain distance from the origin. Case (e) contradicts the main principles of relativity theory since it represents the motion of an object with a speed greater than that of light.
Teacher's Note: On an x/c against t plot, speed over c is the cotangent of the line's angle with the x/c axis.
Exam Note: Line (e) has speed above c, so impossible.
Question 1.56. A world line is directed at an angle θ to the x/c axis (see Problem 1.55). What is the ratio of the kinetic energy calculated via the formula of relativity theory to the value calculated via the formula of classical mechanics? Take the specific case of θ = 60° as an example.
Solution. According to the theory of relativity, the kinetic energy of a moving object is given by the following formula Wrel = m0c2(1/√(1 − β2) − 1), with β = v/c. In classical mechanics, Wcl = m0v2/2. Thus, Wrel/Wcl = (2/β2)(1/√(1 − β2) − 1). Since β = cot θ, we have Wrel/Wcl = (2/cot2θ)(1/√(1 − cot2θ) − 1). At θ = 60° (β = cot 60° = 0.577, β2 = 1/3), Wrel/Wcl = 6(√(3/2) − 1) = 1.35. Corrected: the book prints 1.37; working the numbers gives 1.348, i.e. 1.35.
Teacher's Note: Use β = cotθ; at 60 degrees β² = 1/3, so the relativistic value is only 35% larger.
Exam Note: Substitute β² = 1/3; do the arithmetic carefully.
Question 1.57. Two systems are moving with respect to each other with a certain velocity. The motion of one system in terms of the coordinates x/c and t of the other system is represented by a world line directed at an angle θ to the x/c axis. After a time interval T0 reckoned from the origin of coordinates has elapsed, one system sends a signal to the other. After what time will the second system receive the signal?
Solution. Let us assume that at t = 0 by the clocks in both systems, the systems were close to each other (in the figure accompanying the problem this moment corresponds to the origin). If one of the systems sends a signal after a time interval T0 has elapsed, the second system will receive the signal after a time interval T = T0√((1 + β)/(1 − β)). The angle θ corresponds to a relative velocity β = cot θ. Thus, T = T0√((1 + cot θ)/(1 − cot θ)).
Teacher's Note: This is the relativistic Doppler factor for receding systems; use β = cotθ.
Exam Note: State T = T0√((1+β)/(1−β)).
Question 1.58. Three systems, A, B and C, are moving with respect to each other in such a manner that with respect to system B the velocities of A and C coincide in magnitude and are directed toward B (Figure (a)). When system A comes alongside system B (Figure (b)), the clocks in the two systems are synchronized. At this moment system A begins emitting signals directed at B and separated by equal time intervals T0. This continues until A comes alongside C (Figure (c)), with N signals being sent over the entire interval between the encounters. At this moment the clock in C is synchronized with the clock in A and system C starts to send signals directed at B that are separated by the same time intervals T0. Find the difference in readings of the clocks in B and C when these two systems come alongside (Figure (d)).
Solution. The time interval separating the signals received by B from A is T1 = T0√((1 + β)/(1 − β)). Since system C is moving toward B, its (relative) velocity is negative and, hence, the signals it sends are received by B separated by time intervals T2 = T0√((1 − β)/(1 + β)). System B will register N signals from A in the course of t1 = NT1 = NT0√((1 + β)/(1 − β)), while the signals from C will be registered in the course of t2 = NT2 = NT0√((1 − β)/(1 + β)). When system C meets system B, the clock in the first system (B) will show tB = t1 + t2 = NT0(√((1 + β)/(1 − β)) + √((1 − β)/(1 + β))) = 2NT0/√(1 − β2). The clock in C will show the time that is the sum of the time during which system A sends N signals prior to meeting C and the time during which system C sends N signals prior to meeting system B. Thus, tC = 2NT0. The difference in the readings of the clocks will be Δt = tB − tC = 2(1/√(1 − β2) − 1) NT0. The fractional variation in the duration of the signals is tB/tC = 1/√(1 − β2). For example, at β = 0.6 we have tB/tC = 1.25.
Teacher's Note: Receding signals are stretched, approaching ones compressed; B's total exceeds C's by the time dilation factor.
Exam Note: Use Doppler factors; B reads more than C.
Download LA Sena Solutions for JEE Math PDF
Complete Math Solutions for LA Sena Solutions Physics Chapter 1 Fundamentals of Mechanics
Access the complete chapter-wise PDF for LA Sena Solutions Physics Chapter 1 Fundamentals of Mechanics. These structured LA Sena Solutions solutions for JEE Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Mastering Core Concepts with LA Sena Solutions
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Additional Study Materials for 2026
Wrap up your chapter revision by testing your knowledge against standard objective question formats. Explore our full library of up-to-date syllabus details and mock evaluations to secure top grades in your math examinations.
FAQs
They are chapter-wise solved questions from the LA Sena book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.