IE Irodov Solutions Chapter 7 Hydrodynamics

IE Irodov Solutions for JEE Physics: Chapter 07 Hydrodynamics

Review structured textbook solutions for JEE Physics Chapter 07 Hydrodynamics prepared by IE Irodov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.

Practice JEE Physics Solutions: Chapter 07 Hydrodynamics

Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.

Hydrodynamics - Questions 315 to 339

Hydrodynamics (Part 1)

Question 315. Ideal fluid flows along a flat tube of constant cross-section, located in a horizontal plane and bent as shown in Fig. 1.80 (top view). The flow is steady. Are the pressures and velocities of the fluid equal at points 1 and 2? What is the shape of the streamlines?
Figure 1.80: a flat tube of constant width that turns through a right angle; fluid enters from the top, leaves to the right. Point 1 lies near the outer wall of the bend and point 2 nearer the inner corner.

Solution. Between 1 and 2 fluid particles are in nearly circular motion and therefore have centripetal acceleration. The force for this acceleration, like for any other situation in an ideal fluid, can only come from the pressure variation along the line joining 1 and 2. This requires that the pressure at 1 should be greater than the pressure at 2, i.e.
P1 > P2
so that the fluid particles can have the required acceleration. If there is no turbulence, the motion can be taken as irrotational. Then, considering ∮ v·dl = 0 along a circuit that has two arms along streamlines (near points 1 and 2) and two arms at right angles to the streamlines, we infer that
v2 > v1.
In an incompressible liquid we also have div v = 0. By electrostatic analogy we then find that the density of streamlines is proportional to the velocity at that point (the streamlines crowd together near the inner corner, where the velocity is greater).

Teacher's Note: Centripetal force needs a pressure gradient: higher pressure outside the bend, higher speed inside.

Exam Note: State P1 > P2 and v2 > v1 with the reason.

Question 316. Two manometric tubes are mounted on a horizontal pipe of varying cross-section at the sections S1 and S2 (Fig. 1.81). Find the volume of water flowing across the pipe's section per unit time if the difference in water columns is equal to Δh.
Figure 1.81: a horizontal pipe, narrower at S1 (left) than at S2 (right), each with a vertical manometer tube; the water flows left to right.

Solution. From the conservation of mass
v1S1 = v2S2  (1)
But S1 < S2 as shown in the figure, therefore v1 > v2. As every streamline is horizontal between 1 and 2, Bernoulli's theorem becomes p + ½ρv2 = constant, which gives p1 < p2 as v1 > v2. As the difference in height of the water columns is Δh,
p2 − p1 = ρgΔh  (2)
From Bernoulli's theorem between points 1 and 2 of a streamline
p1 + ½ρv12 = p2 + ½ρv22,
or p2 − p1 = ½ρ(v12 − v22),
or ρgΔh = ½ρ(v12 − v22)  (3) (using Eq. 2).
Using (1) in (3), we get
v1 = S2√[2gΔh/(S22 − S12)].
Hence the volume of water flowing per second is
Q = v1S1 = S1S2√[2gΔh/(S22 − S12)].

Teacher's Note: Continuity gives v2 in terms of v1; Bernoulli plus the manometer height difference fixes v1, then Q = v1S1.

Exam Note: Combine continuity, Bernoulli and ρgΔh correctly.

Question 317. A Pitot tube (Fig. 1.82) is mounted along the axis of a gas pipeline whose cross-sectional area is equal to S. Assuming the viscosity to be negligible, find the volume of gas flowing across the section of the pipe per unit time, if the difference in the liquid columns is equal to Δh, and the densities of the liquid and the gas are ρ0 and ρ respectively.
Figure 1.82: a U-tube manometer under the pipe; one limb opens facing the flow at A (the tip of the Pitot tube) and the other opens in the pipe wall at B.

Solution. Applying Bernoulli's theorem for the points A and B, with vA = 0,
pA = pB + ½ρv2,
or ½ρv2 = pA − pB = Δh ρ0 g.
So v = √(2Δh ρ0 g/ρ).
Thus the rate of flow of gas is Q = Sv = S√(2Δh ρ0 g/ρ).
The gas flows past the tube opening at B, but at A the gas becomes stationary, as the gas will move into the tube which already contains gas. Bernoulli's theorem (p/ρ + ½v2 + gz is constant along a streamline) is here applied somewhat indirectly: the streamline at A is not the streamline at B. Nevertheless the result is correct. To be convinced of this, apply Bernoulli's theorem to the streamline that goes through A by comparing the situation at A with that above B on the same level. In steady conditions this agrees with the result derived, because there cannot be a transverse pressure differential.

Teacher's Note: At the Pitot tip the gas is brought to rest, so the pressure difference equals ½ρv² of the free stream.

Exam Note: Use ρ0 for the liquid and ρ for the gas.

Question 318. A wide vessel with a small hole in the bottom is filled with water and kerosene. Neglecting the viscosity, find the velocity of the water flow, if the thickness of the water layer is equal to h1 = 30 cm and that of the kerosene layer to h2 = 20 cm.
Figure: a vessel with kerosene (thickness h2) floating on water (thickness h1); the hole A is in the bottom.

Solution. Since the density of water is greater than that of kerosene, the water collects at the bottom. The pressure due to the water level is h1ρ1g and that due to the kerosene is h2ρ2g, so the net pressure at the hole is h1ρ1g + h2ρ2g. From Bernoulli's theorem this pressure energy is converted into kinetic energy while flowing through the hole A, i.e.
h1ρ1g + h2ρ2g = ½ρ1v2.
Hence v = √[2(h1 + h2ρ2/ρ1)g] = 3 m/s.
(Check: with ρ2/ρ1 = 0.8 for kerosene, v = √(2 × 9.8 × 0.46) = 3.0 m/s.)

Teacher's Note: Kerosene's pressure counts through its weight; equivalent water head is h1 + h2ρ2/ρ1 = 46 cm.

Exam Note: Use ρ2/ρ1 = 0.8 for kerosene.

Question 319. A wide cylindrical vessel 50 cm in height is filled with water and rests on a table. Assuming the viscosity to be negligible, find at what height from the bottom of the vessel a small hole should be perforated for the water jet coming out of it to hit the surface of the table at the maximum distance lmax from the vessel. Find lmax.

Solution. Let H be the total height of the water column and the hole be made at a height h from the bottom. Then from Bernoulli's theorem
½ρv2 = (H − h)ρg, or v = √(2g(H − h)), directed horizontally.
For the horizontal range, l = vt = √(2g(H − h))·√(2h/g) = 2√(Hh − h2).
For maximum l, d(Hh − h2)/dh = 0, which yields h = H/2 = 25 cm.
Then lmax = 2√(H2/2 − H2/4) = H = 50 cm (the value of lmax is not printed in the book; it is completed here).

Teacher's Note: Range 2√(h(H−h)) is largest at h = H/2, giving l_max = H.

Exam Note: Differentiate range, get h = H/2, then state l_max = 50 cm.

Question 320. A bent tube is lowered into a water stream as shown in Fig. 1.83. The velocity of the stream relative to the tube is equal to v = 2.5 m/s. The closed upper end of the tube located at the height h0 = 12 cm has a small orifice. To what height h will the water jet spurt?
Figure 1.83: an L-shaped tube with its lower open end pointing against the stream and its upper closed end, with a small orifice, standing h0 above the water surface; the jet rises a further height h.

Solution. Let the velocity of the water jet near the orifice be v′. Applying Bernoulli's theorem,
½ρv2 = h0ρg + ½ρv′2,
or v′ = √(v2 − 2gh0)  (1)
Here the pressure term on both sides is the same and equal to atmospheric pressure.
If the jet rises up to a height h, at this height the whole of its kinetic energy is converted into potential energy:
½ρv′2 = ρgh, or h = v′2/2g = v2/2g − h0 = 20 cm [using Eq. (1)].
(Check: 2.52/(2 × 9.8) = 0.319 m = 31.9 cm; 31.9 − 12 = 19.9 cm ≈ 20 cm.)

Teacher's Note: The stream's kinetic head v²/2g is shared between the lift h0 and the jet height h.

Exam Note: Result: h = v²/2g − h0 = 20 cm.

Question 321. The horizontal bottom of a wide vessel with an ideal fluid has a round orifice of radius R1 over which a round closed cylinder is mounted, whose radius R2 > R1 (Fig. 1.84). The clearance between the cylinder and the bottom of the vessel is very small, the fluid density is ρ. Find the static pressure of the fluid in the clearance as a function of the distance r from the axis of the orifice (and the cylinder), if the height of the fluid is equal to h.
Figure 1.84: a closed cylinder of radius R2 stands just above the bottom of the vessel, over a round orifice of radius R1 centred on its axis; fluid of depth h surrounds the cylinder.

Solution. Water flows through the small clearance into the orifice. Let d be the clearance. Then from the equation of continuity
(2πR1d)v1 = (2πrd)v = (2πR2d)v2,
or v1R1 = vr = v2R2  (1)
where v1, v2 and v are respectively the inward radial velocities of the fluid at the orifice edge (1), the outer edge of the cylinder (2) and at the distance r (3).
By Bernoulli's theorem just before 2 and just after it in the clearance
p0 + hρg = p2 + ½ρv22  (2)
Applying the same theorem at 3 and 1 we find that this also equals
p + ½ρv2 = p0 + ½ρv12  (3)
(since the pressure in the orifice is p0).
From Eqs. (2) and (3), v1 = √(2gh)  (4)
and p = p0 + ½ρv12[1 − (v/v1)2]
= p0 + hρg[1 − (R1/r)2] [using (1) and (4)].

Teacher's Note: Radial flow through a thin gap: continuity gives v ∝ 1/r; Bernoulli then gives pressure at each radius.

Exam Note: Final: p = p0 + hρg[1 − (R1/r)²].

Question 322. What work should be done in order to squeeze all water from a horizontally located cylinder during the time t by means of a constant force acting on the piston? The volume of water in the cylinder is equal to V, the cross-sectional area of the orifice to s, with s being considerably less than the piston area. The friction and viscosity are negligibly small.
Figure 1.85: a horizontal cylinder of water (volume V) with a piston on the left pushed by a force, and a small orifice of area s on the right.

Solution. Let the force acting on the piston be F and the length of the cylinder be l. Then work done = Fl  (1)
Applying Bernoulli's theorem for points A (at the piston) and B (at the orifice), p = ½ρv2 where ρ is the density and v is the velocity at B. Now the force on the piston, with A the piston area,
F = pA = ½ρv2A  (2)
Also, the discharge through the orifice during the time t is svt, and this is equal to the volume of the cylinder, i.e.
V = svt, or v = V/(st)  (3)
From Eqs. (1), (2) and (3), the work done
= ½ρv2Al = ½ρA·V2/(st)2·l = ½ρV3/(s2t2) (as Al = V).
Corrected: the printed final line appears to show S3 in the denominator; the correct result from the steps above is A = ½ρV3/(st)2.

Teacher's Note: Constant force means constant exit speed v = V/(st); work = F·l = ½ρv²V.

Exam Note: Write A = ½ρV³/(s²t²).

Question 323. A cylindrical vessel of height h and base area S is filled with water. An orifice of area s ≪ S is opened in the bottom of the vessel. Neglecting the viscosity of water, determine how soon all the water will pour out of the vessel.

Solution. Let at any moment of time the water level in the vessel be H; then the speed of flow of water through the orifice at that moment is
v = √(2gH)  (1)
In the time interval dt the volume of water ejected through the orifice is
dV = sv dt  (2)
On the other hand, the volume of water in the vessel at that time is V = SH. Differentiating, dV = S dH  (3) (taken as the magnitude of the decrease).
From (2) and (3), S dH = sv dt, or dt = (S/s)·dH/√(2gH).
Integrating, ∫0t dt = (S/(s√(2g))) ∫0h dH/√H.
Thus t = (S/s)√(2h/g).

Teacher's Note: Efflux speed falls with level, so integrate dt = (S/s)dH/√(2gH); time is twice the constant-speed estimate.

Exam Note: Set up the differential equation, integrate to (S/s)√(2h/g).

Question 324. A horizontally oriented tube AB of length l rotates with a constant angular velocity ω about a stationary vertical axis OO′ passing through the end A (Fig. 1.86). The tube is filled with an ideal fluid. The end A of the tube is open, the closed end B has a very small orifice. Find the velocity of the fluid relative to the tube as a function of the column "height" h.
Figure 1.86: tube AB lying horizontally, A on the axis OO′, B at distance l; the fluid column of length h occupies the part next to B, which has a small orifice.

Solution. In a rotating frame (with constant angular velocity) the Eulerian equation is
−∇p + ρg + 2ρ(v′ × ω) + ρω2r = ρ dv′/dt.
In the frame of the rotating tube the liquid in the "column" is practically static because the orifice is sufficiently small. Thus the Eulerian equation in projection form along r (the position vector of an arbitrary liquid element of length dr relative to the rotation axis) reduces to
−dp/dr + ρω2r = 0, or dp = ρω2r dr,
so ∫p0p dp = ρω2∫(l−h)r r dr.
Thus p(r) = p0 + (ρω2/2)[r2 − (l − h)2]  (1)
Hence the pressure at the end B just before the orifice is
p(l) = p0 + (ρω2/2)(2lh − h2)  (2)
Then applying Bernoulli's theorem at the orifice for the points just inside and outside the end B,
p0 + ½ρω2(2lh − h2) = p0 + ½ρv2 (where v is the sought velocity).
So v = ωh√(2l/h − 1) = ω√(h(2l − h)).

Teacher's Note: In the rotating frame the column is static, so centrifugal pressure builds up toward B and drives the efflux.

Exam Note: Integrate dp = ρω²r dr from the free surface, then Bernoulli.

Question 325. Demonstrate that in the case of a steady flow of an ideal fluid Eq. (1.7a) turns into the Bernoulli equation.

Solution. The Euler equation is ρ dv/dt = f − ∇p = −∇(p + ρgz), where z is measured vertically upwards.
Now dv/dt = ∂v/∂t + (v·∇)v  (1)
But (v·∇)v = ∇(½v2) − v × curl v  (2)
We consider the steady flow (∂v/∂t = 0) of an incompressible fluid, so ρ is constant, and the motion is irrotational, curl v = 0. So from (1) and (2)
ρ∇(½v2) = −∇(p + ρgz),
or ∇(p + ½ρv2 + ρgz) = 0.
Hence p + ½ρv2 + ρgz = constant.

Teacher's Note: Steady + incompressible + irrotational turns Euler's equation into the gradient of one scalar, which is therefore constant.

Exam Note: State all three assumptions: steady, incompressible, irrotational.

Question 326. On the opposite sides of a wide vertical vessel filled with water two identical holes are opened, each having the cross-sectional area S = 0.50 cm2. The height difference between them is equal to Δh = 51 cm. Find the resultant force of reaction of the water flowing out of the vessel.
Figure: holes A and B on opposite walls, A at depth h below the surface and B a further Δh lower.

Solution. Let the velocity of water flowing through A be vA and that through B be vB; then the discharge rate through A is QA = SvA and similarly through B is SvB. The force of reaction at A is
FA = ρQAvA = ρSvA2, and similarly FB = ρSvB2.
The two forces are opposite in direction, hence the net force has magnitude
F = ρS(vB2 − vA2)  (1)
Applying Bernoulli's theorem to the liquid flowing out of A we get
p0 + ρgh = p0 + ½ρvA2,
and similarly at B, p0 + ρg(h + Δh) = p0 + ½ρvB2.
Hence (vB2 − vA2)ρ/2 = Δhρg.
Thus F = 2ρgSΔh = 0.50 N.
(Check: 2 × 1000 × 9.8 × 0.50×10−4 × 0.51 = 0.4998 N.)

Teacher's Note: Each jet gives a recoil ρSv² = 2ρghS; the two recoils oppose, so the net depends only on Δh.

Exam Note: Net force = 2ρgSΔh = 0.50 N.

Question 327. The side wall of a wide vertical cylindrical vessel of height h = 75 cm has a narrow vertical slit running all the way down to the bottom of the vessel. The length of the slit is l = 50 cm and the width b = 1.0 mm. With the slit closed, the vessel is filled with water. Find the resultant force of reaction of the water flowing out of the vessel immediately after the slit is opened.

Solution. Consider an element of height dy at a distance y from the top. The velocity of the fluid coming out of the element is v = √(2gy).
The force of reaction dF due to this is dF = ρ dA v2 (as in the previous problem) = ρ(b dy)·2gy.
Integrating, F = ρgb ∫h−lh 2y dy = ρgb[h2 − (h − l)2] = ρgbl(2h − l).
(The slit runs from a depth h − l to a depth h from the top.)
Numerically, F = 1000 × 9.8 × 1.0×10−3 × 0.50 × (1.5 − 0.50) = 4.9 N (the numerical value is not printed in the book; it is added here).

Teacher's Note: Each strip at depth y gives recoil ρ·b dy·2gy; sum over the slit's depth range.

Exam Note: Integrate from depth h−l to h; evaluate 4.9 N.

Hydrodynamics (Part 2)

Question 328. Water flows out of a big tank along a tube bent at right angles: the inside radius of the tube is equal to r = 0.50 cm (Fig. 1.87). The length of the horizontal section of the tube is equal to l = 22 cm. The water flow rate is Q = 0.50 litres per second. Find the moment of reaction forces of flowing water, acting on the tube's walls, relative to the point O.
Figure 1.87: a horizontal tube of length l leaves the side of the tank at point O and bends through a right angle downward at its far end, where the water falls out.

Solution. Let the velocity of water flowing through the tube at a certain instant be u = Q/(πr2), where Q is the rate of flow of water and πr2 is the cross-section area of the tube. From the impulse-momentum theorem, for the stream of water striking the tube corner, in the x direction (along the horizontal section, towards the bend) in the time interval dt, Fxdt = −ρQu dt, or Fx = −ρQu, and similarly Fy = ρQu (y downward).
Therefore the force exerted on the water stream by the tube is F′ = −ρQu i + ρQu j. According to the third law, the reaction force on the tube's wall by the stream equals −F′ = ρQu i − ρQu j.
Hence the sought moment of force about O becomes
N = l(−i) × (ρQu i − ρQu j) = ρQul k = (ρQ2/(πr2))·l k,
and |N| = ρQ2l/(πr2) = 0.70 N·m.
(Check: 1000 × (0.5×10−3)2 × 0.22/(π × (0.5×10−2)2) = 0.700 N·m.)

Teacher's Note: Only the vertical recoil ρQu at the far end has lever arm l about O.

Exam Note: Give the magnitude ρQ²l/(πr²) = 0.70 N·m.

Question 329. A side wall of a wide open tank is provided with a narrowing tube (Fig. 1.88) through which water flows out. The cross-sectional area of the tube decreases from S = 3.0 cm2 to s = 1.0 cm2. The water level in the tank is h = 4.6 m higher than that in the tube. Neglecting the viscosity of the water, find the horizontal component of the force tending to pull the tube out of the tank.
Figure 1.88: a conical nozzle fixed to the side wall of a tank, narrowing from area S at the tank to area s at the outer end where the jet leaves.

Solution. Suppose the radius at A is R and it decreases uniformly to r at B, where S = πR2 and s = πr2. Assume also that the semi-vertical angle of the cone (with vertex O) is θ. Then R/L2 = r/L1 = y/x, so y = r + [(R − r)/(L2 − L1)](x − L1), where y is the radius at the point P distant x from the vertex O. Suppose the velocity with which the liquid flows is V at A, v at B and u at P. Then by the equation of continuity
πR2V = πr2v = πy2u.
The velocity of efflux is v = √(2gh) and Bernoulli's theorem gives
pP + ½ρu2 = p0 + ½ρv2,
where pP is the pressure at P and p0 is the atmospheric pressure just outside B. The force on the nozzle tending to pull it out is then
F = ∫(pP − p0) sinθ · 2πy ds.
We have subtracted p0, the force due to atmospheric pressure; the factor sinθ gives the horizontal component and ds = dx secθ is the length of the element of the nozzle surface, with tanθ = (R − r)/(L2 − L1). Thus
F = ∫L1L2 ½(v2 − u2)ρ·2πy·[(R − r)/(L2 − L1)] dx
= πρ ∫rR v2(1 − r4/y4) y dy
= πρv2·½(R2 − r2 + r4/R2 − r2) = ρgh·π(R2 − r2)2/R2
= ρgh(S − s)2/S = 6.02 N on putting the values (taking g = 9.81 m/s2).
Note: if we try to calculate F from the momentum change of the liquid flowing out, it will be wrong even as regards the sign of the force. There is of course the effect of pressure at S and s, but a quantitative derivation of F from Newton's law is difficult.

Teacher's Note: Integrate the pressure excess over the cone wall; the force equals ρgh(S−s)²/S, not the momentum flux.

Exam Note: Show the integral, then ρgh(S−s)²/S = 6.0 N.

Question 330. A cylindrical vessel with water is rotated about its vertical axis with a constant angular velocity ω. Find: (a) the shape of the free surface of the water; (b) the water pressure distribution over the bottom of the vessel along its radius, provided the pressure at the central point is equal to p0.

Solution. The Euler equation is ρ dv/dt = f − ∇p in the space-fixed frame, where f = −ρg k (downward). We assume an incompressible fluid, so ρ is constant. Then f = −∇(ρgz), where z is the height vertically upwards from some fixed origin. We go to the rotating frame, where the equation becomes
ρ dv′/dt = −∇(p + ρgz) + ρω2r + 2ρ(v′ × ω).
The additional terms on the right are the well-known Coriolis and centrifugal forces. In the frame rotating with the liquid v′ = 0, so
∇(p + ρgz − ½ρω2r2) = 0, or p + ρgz − ½ρω2r2 = constant.
(a) On the free surface p = constant, thus z = (ω2/2g)r2 + constant. If we choose the origin at the point r = 0 (i.e. on the axis) of the free surface, then the constant = 0 and
z = ω2r2/(2g) (a paraboloid of revolution).
(b) At the bottom z = constant, so p = ½ρω2r2 + constant. If p = p0 on the axis at the bottom, then
p = p0 + ½ρω2r2.

Teacher's Note: In the rotating frame the liquid is at rest, so p + ρgz − ½ρω²r² is constant.

Exam Note: Answers: z = ω²r²/2g, and p = p0 + ½ρω²r².

Question 331. A thin horizontal disc of radius R = 10 cm is located within a cylindrical cavity filled with oil whose viscosity η = 0.08 P (Fig. 1.89). The clearance between the disc and the horizontal planes of the cavity is equal to h = 1.0 mm. Find the power developed by the viscous forces acting on the disc when it rotates with the angular velocity ω = 60 rad/s. The end effects are to be neglected.
Figure 1.89: a thin disc on a vertical shaft rotating inside a flat cylindrical cavity full of oil, with a small gap h above and below the disc.

Solution. When the disc rotates, the fluid in contact with it corotates, but the fluid in contact with the walls of the cavity does not rotate. A velocity gradient is then set up, leading to viscous forces. At a distance r from the axis the linear velocity is ωr, so there is a velocity gradient ωr/h both in the upper and lower clearance. The corresponding force on the element whose radial width is dr is
η·2πr dr·(ωr/h) (from F = ηA dv/dx).
The torque due to this force is η·2πr dr·(ωr/h)·r, and the net torque considering both the upper and lower clearance is
2∫0R η·2πr3(ω/h) dr = πR4ωη/h.
So the power developed (by the viscous forces, in magnitude) is
P = Nω = πR4ω2η/h = 9.05 W on putting the values (η = 0.08 P = 0.008 Pa·s).
(As instructed, end effects, i.e. the rotation of fluid in the clearance at r > R, have been neglected.)

Teacher's Note: Linear velocity gradient ωr/h in each gap; integrate torque over the disc and double for two faces.

Exam Note: Convert poise: 0.08 P = 0.008 Pa·s; P = 9.05 W.

Question 332. A long cylinder of radius R1 is displaced along its axis with a constant velocity v0 inside a stationary co-axial cylinder of radius R2. The space between the cylinders is filled with viscous liquid. Find the velocity of the liquid as a function of the distance r from the axis of the cylinders. The flow is laminar.

Solution. Consider a coaxial cylinder of radius r and thickness dr. The force of friction (viscous force) on this elemental layer, of length l, is F = 2πrlη dv/dr. This force must be constant from layer to layer so that steady motion may be possible. So
F dr/r = 2πlη dv  (1)
Integrating from R2 (where v = 0) to r: F ∫R2r dr/r = 2πlη ∫0v dv,
or F ln(r/R2) = 2πlηv  (2)
Putting r = R1 (where v = v0): F ln(R1/R2) = 2πlηv0  (3)
From (2) by (3) we get
v = v0 · ln(r/R2)/ln(R1/R2).
Note: the force F is supplied by the agency which tries to carry the inner cylinder with velocity v0.

Teacher's Note: Steady laminar flow needs the same viscous force on every cylindrical layer, giving a logarithmic velocity profile.

Exam Note: Answer: v = v0 ln(r/R2)/ln(R1/R2).

Question 333. A fluid with viscosity η fills the space between two long co-axial cylinders of radii R1 and R2, with R1 < R2. The inner cylinder is stationary while the outer one is rotated with a constant angular velocity ω2. The fluid flow is laminar. Taking into account that the friction force acting on a unit area of a cylindrical surface of radius r is defined by the formula σ = ηr(∂ω/∂r), find: (a) the angular velocity of the rotating fluid as a function of radius r; (b) the moment of the friction forces acting on a unit length of the outer cylinder.

Solution. (a) Consider an elemental cylinder of radius r, length l and thickness dr. From Newton's formula
F = 2πrl·ηr(dω/dr) = 2πlηr2(dω/dr),
and the moment of this force acting on the element is
N = 2πr2lη(dω/dr)·r = 2πr3lη(dω/dr),
or 2πlη dω = N dr/r3  (2)
As in the previous problem N is constant when conditions are steady. Integrating from R1 (ω = 0) to r,
2πlη ∫0ω dω = N ∫R1r dr/r3,
or 2πlηω = (N/2)[1/R12 − 1/r2]  (3)
Putting r = R2, ω = ω2, we get
2πlηω2 = (N/2)[1/R12 − 1/R22]  (4)
From (3) and (4),
ω = ω2·[R12R22/(R22 − R12)]·[1/R12 − 1/r2].
(b) From Eq. (4),
N1 = N/l = 4πηω2·R12R22/(R22 − R12).

Teacher's Note: Torque is the same on every cylindrical layer; integrate dω = N dr/(2πlηr³) with ω = 0 at R1.

Exam Note: Give both ω(r) and the torque per unit length.

Question 334. A tube of length l and radius R carries a steady flow of fluid whose density is ρ and viscosity η. The fluid flow velocity depends on the distance r from the axis of the tube as v = v0(1 − r2/R2). Find: (a) the volume of the fluid flowing across the section of the tube per unit time; (b) the kinetic energy of the fluid within the tube's volume; (c) the friction force exerted on the tube by the fluid; (d) the pressure difference at the ends of the tube.

Solution. (a) Let dV be the volume flowing per second through the cylindrical shell of thickness dr; then
dV = (2πr dr)v0(1 − r2/R2) = 2πv0(r − r3/R2) dr,
and the total volume per second is
V = 2πv0 ∫0R(r − r3/R2) dr = 2πv0·R2/4 = (π/2)R2v0.
(b) Let dT be the kinetic energy within the above cylindrical shell. Then
dT = ½(dm)v2 = ½(2πrl dr ρ)v2 = πlρv02[r − 2r3/R2 + r5/R4] dr.
Hence the total kinetic energy of the fluid is
T = πlρv02 ∫0R(r − 2r3/R2 + r5/R4) dr = πR2ρlv02/6.
(c) The frictional force is the shearing force on the tube exerted by the fluid, which equals −ηS dv/dr (S being the area of the tube wall). Given v = v0(1 − r2/R2), dv/dr = −2v0r/R2, and at r = R, dv/dr = −2v0/R. Then the viscous force is
F = −η(2πRl)(dv/dr)r=R = −2πRlη(−2v0/R) = 4πηv0l.
(d) Taking a cylindrical shell (a cylinder of radius r), the viscous force on it is F = −η(2πrl) dv/dr. Let Δp be the pressure difference; since the flow is steady, the net force on the fluid of radius r is zero:
Δp·πr2 + 2πηlr dv/dr = 0,
or Δp = −2πηlr(dv/dr)/(πr2) = −2ηl(−2v0r/R2)/r = 4ηv0l/R2.

Teacher's Note: Integrate shell by shell; wall friction needs dv/dr at R; steady flow balances pressure and friction.

Exam Note: Answers: πR²v0/2, πR²ρlv0²/6, 4πηv0l, 4ηv0l/R².

Question 335. In the arrangement shown in Fig. 1.90 a viscous liquid whose density is ρ = 1.0 g/cm3 flows along a tube out of a wide tank A. Find the velocity of the liquid flow, if h1 = 10 cm, h2 = 20 cm, and h3 = 35 cm. All the distances l are equal.
Figure 1.90: a horizontal tube leaves the bottom of tank A (liquid depth h3); two vertical manometer tubes stand on it at distances l and 2l from the tank, with liquid heights h2 and h1; the tube ends at a further distance l from the second manometer, where the liquid leaves.

Solution. The loss of pressure head in travelling a distance l is seen from the middle section to be h2 − h1 = 10 cm. Since h3 − h2 = 15 cm = 5 cm + (h2 − h1), we see that a pressure head of 5 cm remains uncompensated and must be converted into kinetic energy, the liquid flowing out. Thus
ρv2/2 = ρgΔh, where Δh = (h3 − h2) − (h2 − h1) = h3 − 2h2 + h1 = 5 cm.
Thus v = √(2gΔh) = 1 m/s.
Corrected: the book writes Δh = h3 − h2, which would give 15 cm; the 5 cm used in the working (and the answer 1 m/s) corresponds to the expression above. Check: √(2 × 9.8 × 0.05) = 0.99 m/s.

Teacher's Note: Viscous head loss per length l is h2 − h1; only the remaining head becomes kinetic energy.

Exam Note: Net head is 5 cm, not 15 cm; v ≈ 1 m/s.

Question 336. The cross-sectional radius of a pipeline decreases gradually as r = r0e−αx, where α = 0.50 m−1, x is the distance from the pipeline inlet. Find the ratio of Reynolds numbers for two cross-sections separated by Δx = 3.2 m.

Solution. We know that Reynolds' number is defined as Re = ρvl/η, where v is the velocity, l is the characteristic length and η the coefficient of viscosity. In the case of a circular cross-section the characteristic length is the diameter d of the cross-section, and v is taken as the average velocity of flow of the liquid. Now, Re1 (Reynolds' number at x1) = ρd1v1/η, where v1 is the velocity at distance x1, and similarly Re2 = ρd2v2/η, so
Re1/Re2 = d1v1/(d2v2).
From the equation of continuity, A1v1 = A2v2, or πr12v1 = πr22v2, or d1v1r1 = d2v2r2, so
d1v1/(d2v2) = r2/r1 = r0e−αx2/(r0e−αx1) = e−αΔx (as x2 − x1 = Δx).
Thus Re2/Re1 = eαΔx = e1.6 ≈ 5.

Teacher's Note: Since Re ∝ dv and v ∝ 1/r², Re ∝ 1/r: the narrower section has the larger Reynolds number.

Exam Note: Result: Re2/Re1 = e^(αΔx) ≈ 5.

Question 337. When a sphere of radius r1 = 1.2 mm moves in glycerin, the laminar flow is observed if the velocity of the sphere does not exceed v1 = 23 cm/s. At what minimum velocity v2 of a sphere of radius r2 = 5.5 cm will the flow in water become turbulent? The viscosities of glycerin and water are equal to η1 = 13.9 P and η2 = 0.011 P respectively.

Solution. The Reynolds number for turbulent flow is greater than that for laminar flow. Taking the sphere diameter as the characteristic length,
(Re)l = ρ1v1d/η1 = 2ρ1v1r1/η1 and (Re)t = 2ρ2v2r2/η2.
But (Re)t ≥ (Re)l, so
v2,min = ρ1v1r1η2/(ρ2r2η1) = 5 μm/s on putting the values.
(The densities are not given in the problem; the value 5 μm/s uses ρ1/ρ2 = 1.26 for glycerin to water, which is checked: 1.26 × (1.2/55) × (0.011/13.9) × 0.23 m/s = 5.0×10−6 m/s.)

Teacher's Note: Turbulence sets in at the same critical Reynolds number, so equate ρvr/η for the two cases.

Exam Note: State densities used (glycerin 1.26 g/cm³); answer 5 μm/s.

Question 338. A lead sphere is steadily sinking in glycerin whose viscosity is equal to η = 13.9 P. What is the maximum diameter of the sphere at which the flow around that sphere still remains laminar? It is known that the transition to the turbulent flow corresponds to Reynolds number Re = 0.5. (Here the characteristic length is taken to be the sphere diameter.)

Solution. We have Re = vρ0d/η and v is given by (steady sinking, buoyancy included)
6πηrv = (4π/3)r3(ρ − ρ0)g
(ρ = density of lead, ρ0 = density of glycerin), so
v = (2/9η)(ρ − ρ0)gr2 = (1/18η)(ρ − ρ0)gd2.
Thus Re = (1/18η2)(ρ − ρ0)gρ0d3 = 1/2,
and d = [9η2/(ρ0(ρ − ρ0)g)]1/3 = 5.2 mm on putting the values.
(Check with η = 1.39 Pa·s, ρ0 = 1260 kg/m3, ρ = 11300 kg/m3: d3 = 9 × 1.93/(1260 × 10040 × 9.8) = 1.40×10−7 m3, d = 5.2 mm.)

Teacher's Note: Terminal speed from Stokes' law balanced against weight minus buoyancy; then impose Re = 0.5.

Exam Note: Equate Stokes drag to net weight, then Re = 0.5.

Question 339. A steel ball of diameter d = 3.0 mm starts sinking with zero initial velocity in olive oil whose viscosity is η = 0.90 P. How soon after the beginning of motion will the velocity of the ball differ from the steady-state velocity by n = 1.0%?

Solution. m dv/dt = mg − 6πηrv, or dv/dt + kv = g, where k = 6πηr/m.
Multiplying by ekt: d(ektv)/dt = gekt, so vekt = (g/k)ekt + C, or v = g/k + Ce−kt (C a constant).
Since v = 0 at t = 0, C = −g/k. Thus v = (g/k)(1 − e−kt).
The steady-state velocity is g/k. The velocity differs from g/k by the fraction n when e−kt = n, i.e.
t = (1/k) ln(1/n).
Here 1/k = m/(6πηr) = (4π/3)r3ρ/(6πηr) = 4r2ρ/(18η) = d2ρ/(18η) (buoyancy in olive oil neglected).
Corrected: the book writes t = (1/k) ln n with 1/k = −d2ρ/(18η); the two sign slips cancel, and the correct form is as above. Taking ρ = 7.8 g/cm3 for steel (not given in the problem): d2ρ/(18η) = (9×10−6 × 7800)/(18 × 0.09) = 0.0433 s, and t = 0.0433 × ln 100 = 0.20 s.

Teacher's Note: Velocity approaches terminal value exponentially, v = v_t(1 − e^(−t/τ)), with τ = m/(6πηr).

Exam Note: State assumed steel density 7.8 g/cm³; t ≈ 0.2 s.

IE Irodov Solutions for JEE Mathematics: IE Irodov Solutions Chapter 7 Hydrodynamics

Chapter-wise IE Irodov Solutions: IE Irodov Solutions Chapter 7 Hydrodynamics

Explore reliable mathematical solutions for IE Irodov Solutions Chapter 7 Hydrodynamics tailored for JEE learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.

Step-by-Step Mathematical Explanations

Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.

Additional Study Materials for 2026

In addition to these IE Irodov Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.

FAQs

What are these IE Irodov Solutions for JEE Physics?

They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.

Are the IE Irodov JEE Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these IE Irodov solutions for JEE Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising IE Irodov JEE Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these JEE Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.