IE Irodov Solutions Chapter 6 Elastic Deformations Of A Solid Body

Download JEE Physics IE Irodov Textbook Solutions: Chapter 06 Elastic Deformations Of A Solid Body

Review structured textbook solutions for JEE Physics Chapter 06 Elastic Deformations Of A Solid Body prepared by IE Irodov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.

Access IE Irodov Textbook Answers and Solutions

View or download the dedicated Chapter 06 Elastic Deformations Of A Solid Body solution resource below. Engaging with these textbook answers under focused study conditions ensures continuous academic progress and mastery of the 2026 curriculum for Physics.

Elastic Deformations Of A Solid Body - Problems 290 to 314

Chapter 6: Elastic Deformations Of A Solid Body

Question 290. What pressure has to be applied to the ends of a steel cylinder to keep its length constant on raising its temperature by 100°C?

Solution. Variation of length with temperature: lt = l0(1 + αΔt), or Δl/l0 = αΔt = ε.

But ε = σ/E, so σ = αΔtE, which is the sought stress (pressure).

Putting the values of α and E from the Appendix and Δt = 100°C, we get σ = 2.2 × 103 atm.

Teacher's Note: Thermal expansion prevented entirely turns into compressive stress; equate thermal strain αΔt to elastic strain σ/E.

Exam Note: Write σ = αEΔt first, then substitute.

Question 291. What internal pressure (in the absence of an external pressure) can be sustained
(a) by a glass tube;
(b) by a glass spherical flask,
if in both cases the wall thickness is equal to Δr = 1.0 mm and the radius of the tube and the flask equals r = 25 mm?

Solution. (a) Consider a transverse section of the tube and concentrate on an element which subtends an angle Δφ at the centre. The forces acting on a portion of length Δl on the element are:

(1) tensile forces at the sides, each of magnitude σΔrΔl. Their resultant, directed radially towards the centre, is 2σΔrΔl sin(Δφ/2) ≈ σΔrΔlΔφ.

(2) The force due to fluid pressure, p·rΔφ·Δl.

Since these balance, pmax = σmΔr/r, where σm is the maximum tensile stress. Putting the values, pmax = 19.7 atm.

(b) Consider a small cap of area dS = π(rΔθ/2)2 about an arbitrarily chosen axis. There are tangential tensile forces all around the ring of the cap. Their resultant is σ[2π(rΔθ/2)Δr] sin(Δθ/2). Hence, in the limit,

pm π(rΔθ/2)2 = σm π(rΔθ/2) ΔrΔθ,

or pm = 2σmΔr/r = 39.5 atm.

Teacher's Note: Thin-wall pressure balance: tube p = σΔr/r, sphere p = 2σΔr/r, so sphere holds twice as much.

Exam Note: Memorise both results; sphere is double the tube.

Question 292. A horizontally oriented copper rod of length l = 1.0 m is rotated about a vertical axis passing through its middle. What is the number of rps at which this rod ruptures?

Solution. Consider an element of the rod at a distance x from the rotation axis. From Newton's second law in projection form directed towards the axis:

−dT = (dm)ω2x = (m/l) ω2 x dx.

On integrating, −T = (mω2/l)(x2/2) + C. At the free end x = ±l/2, T = 0, so C = −mω2l/8. Hence T = (mω2/2)(l/4 − x2/l).

Thus Tmax = mω2l/8 (at the mid point).

Condition for rupture: Tmax = Sσm, so mω2l/8 = Sσm, or ω = (2/l)√(2σm/ρ).

Hence the sought number of rps is n = ω/2π = (1/πl)√(2σm/ρ) = 0.8 × 102 rps (using the table).

Teacher's Note: Tension is maximum at the axis and zero at free ends; integrate centrifugal force from the end inward.

Exam Note: Quote T = mω²l/8 at the centre.

Question 293. A ring of radius r = 25 cm made of lead wire is rotated about a stationary vertical axis passing through its centre and perpendicular to the plane of the ring. What is the number of rps at which the ring ruptures?

Solution. Consider an element of the ring subtending angle dθ. From Newton's law Fn = mwn for this element:

T dθ = (m/2π) dθ ω2r, so T = mω2r/2π.

Condition for the problem: T/(πrw2) ≤ σm (rw is the wire radius; the wire's cross-section is S), which leads to ω2max = σm/(ρr2).

Thus the sought number of rps is n = ωmax/2π = (1/2πr)√(σm/ρ). Using the table of appendices, n = 23 rps.

Teacher's Note: Ring tension is T = mω²r/2π; set stress T/S equal to breaking stress, so wire thickness cancels.

Exam Note: Show that wire cross-section cancels in the result.

Question 294. A steel wire of diameter d = 1.0 mm is stretched horizontally between two clamps located at the distance l = 2.0 m from each other. A weight of mass m = 0.25 kg is suspended from the midpoint O of the wire. What will the resulting descent of the point O be in centimetres?

Solution. Let the point O descend by the distance x. From the equilibrium of point O: 2T sinθ = mg, or T = mg/(2 sinθ) = (mg/2x)√((l/2)2 + x2). (1)

Also T/(π(d/2)2) = σ = εE, or T = εEπd2/4. (2) (σ is stress and ε is strain.)

In addition, ε = [√((l/2)2 + x2) − l/2]/(l/2) = √(1 + (2x/l)2) − 1. (3)

From Eqs. (1), (2) and (3), for x ≪ l (ε ≈ 2x2/l2, T ≈ mgl/4x):

2x3/l2 = mgl/(πEd2), so x = l (mg/(2πEd2))1/3 = 2.5 cm.

Teacher's Note: Use equilibrium at O plus Hooke's law; small-angle approximation gives strain ≈ 2x²/l², leading to a cube root.

Exam Note: State the small-sag approximation x ≪ l explicitly.

Question 295. A uniform elastic plank moves over a smooth horizontal plane due to a constant force F0 distributed uniformly over the end face. The surface of the end face is equal to S, and Young's modulus of the material to E. Find the compressive strain of the plank in the direction of the acting force.

Solution. Consider an element of the plank at a distance x from the free end. The internal forces T produce the deformation and dT provides the acceleration. From Newton's law for the element:

dT = (dm)w = (m/l)dx · F0/m = (F0/l) dx.

As the free end has zero tension, integrating gives T = F0x/l.

Deformation of the element dx: dξ = (σ/E)dx = (T/SE)dx = F0x dx/(SEl).

Total deformation: ξ = (F0/SEl) ∫0l x dx = F0l/(2SE).

Hence the sought strain is ξ/l = F0/(2SE).

Teacher's Note: Internal force grows linearly from zero at the free end, so mean strain is half the static value.

Exam Note: Answer is F₀/2SE, not F₀/SE.

Question 296. A thin uniform copper rod of length l and mass m rotates uniformly with an angular velocity ω in a horizontal plane about a vertical axis passing through one of its ends. Determine the tension in the rod as a function of the distance r from the rotation axis. Find the elongation of the rod.

Solution. Consider an element of the rod at a distance r from the rotation axis. From Newton's second law in projection form directed toward the axis:

T − (T + dT) = (dm)ω2r, or −dT = (m/l)ω2r dr.

At the free end the tension is zero. Integrating, T = (mω2/l)(l2 − r2)/2 = (mω2l/2)(1 − r2/l2).

Elongation of the element dr: dξ = (σ(r)/E)dr = (T/SE)dr (S is the cross-sectional area), so dξ = (mω2l/2SE)(1 − r2/l2)dr.

Thus the sought elongation is ξ = ∫dξ = (mω2l/2SE)(2l/3) = ρω2l3/(3E) (where ρ is the density of copper, m = Slρ).

Teacher's Note: Tension falls parabolically from the axis to the free end; elongation needs integrating strain T/SE over length.

Exam Note: Give T(r) and ξ = ρω²l³/3E.

Question 297. A solid copper cylinder of length l = 65 cm is placed on a horizontal surface and subjected to a vertical compressive force F = 1000 N directed downward and distributed uniformly over the end face. What will be the resulting change of the volume of the cylinder in cubic millimetres?

Solution. Volume of a solid cylinder V = πr2l, so ΔV/V = 2Δr/r + Δl/l. (1)

The longitudinal strain Δl/l and the accompanying lateral strain Δr/r are related as Δr/r = −μ Δl/l. (2)

Using (2) in (1): ΔV/V = (Δl/l)(1 − 2μ). (3)

But Δl/l = −(F/πr2)/E (the increment in length is negative), so ΔV/V = −F(1 − 2μ)/(πr2E).

Thus ΔV = −Fl(1 − 2μ)/E. The negative sign means the volume of the cylinder has decreased.

Numerically (E = 130 GPa, μ = 0.34 for copper): |ΔV| = 1000 × 0.65 × 0.32/(1.3 × 1011) ≈ 1.6 × 10−9 m3 ≈ 1.6 mm3 (decrease).

Teacher's Note: Volume change uses both axial and lateral (Poisson) strain; ΔV/V = (1−2μ)Δl/l is independent of radius.

Exam Note: Do not forget the (1−2μ) factor and sign.

Question 298. A copper rod of length l is suspended from the ceiling by one of its ends. Find:
(a) the elongation Δl of the rod due to its own weight;
(b) the relative increment of its volume ΔV/V.

Solution. (a) The free end has zero tension, so the tension at a vertical distance y from the lower end is T = (m/l)gy. Let dl be the elongation of the element of length dy:

dl = (σ(y)/E)dy = (T/SE)dy = (mgy/SlE)dy = ρgy dy/E (ρ is the density of copper).

Thus the sought elongation Δl = ∫dl = (ρg/E)∫0l y dy = ρgl2/(2E).

(b) If the longitudinal (tensile) strain is ε = Δl/l, the accompanying lateral (compressive) strain is ε′ = Δr/r = −με. Since V = πr2l, ΔV/V = 2Δr/r + Δl/l = (1 − 2μ)Δl/l, where Δl/l is given by part (a) and μ is the Poisson ratio for copper. That is, ΔV/V = (1 − 2μ)ρgl/(2E).

Teacher's Note: Own weight makes tension vary with height; integrate dl = ρgy dy/E. Volume strain follows from Poisson's ratio.

Exam Note: Show integral of ρgy/E; then multiply by (1−2μ).

Question 299. A bar made of material whose Young's modulus is equal to E and Poisson's ratio to μ is subjected to the hydrostatic pressure p. Find:
(a) the fractional decrement of its volume;
(b) the relationship between the compressibility β and the elastic constants E and μ.

Solution. (a) Consider a cube of unit length before pressure is applied. The pressure acts on each face. The pressure on one pair of opposite faces produces a compression p/E along that direction and a lateral extension μp/E due to the pressures on the other faces.

The net result is a compression (p/E)(1 − 2μ) in each side. Hence ΔV/V = −(3p/E)(1 − 2μ), because by symmetry ΔV/V = 3Δl/l.

(b) Consider a cube under an equal compressive stress σ acting on all its faces. Then volume strain = −ΔV/V = σ/k (1), where k is the bulk modulus of elasticity. So σ/k = (3σ/E)(1 − 2μ), or E = 3k(1 − 2μ) = (3/β)(1 − 2μ) (as k = 1/β), i.e. β = 3(1 − 2μ)/E.

μ ≤ 1/2 if E and β are both to remain positive.

Teacher's Note: Superpose three axial strains: each face pressure compresses along its axis and expands along the other two via μ.

Exam Note: Result: β = 3(1−2μ)/E, hence μ ≤ 1/2.

Question 300. One end of a steel rectangular girder is embedded into a wall (Fig. 1.74). Due to gravity it sags slightly. Find the radius of curvature of the neutral layer (the dotted line in the figure) in the vicinity of the point O if the length of the protruding section of the girder is equal to l = 6.0 m and the thickness of the girder equals h = 10 cm.
(Fig. 1.74: a horizontal girder of thickness h clamped into a wall at O, protruding length l, with the neutral layer shown as a dotted line along its middle.)

Solution. A beam clamped at one end and supporting a load at the free end is called a cantilever. The key result is that elastic forces in the beam generate a couple, called the moment of resistance, which balances the external bending moment due to the weight of the beam, load, etc. The internal bending moment is given by EI/R, where R is the radius of curvature of the beam at the representative point (x, y) and I = ∫z2dS is the geometrical moment of inertia of the cross-section relative to the axis passing through the neutral layer, which remains unstretched.

The section of the beam beyond P exerts the bending moment N(x), so EI/R = N(x). If there is no load other than the weight of the beam, N(x) = ½ρg(l − x)2bh, where ρ is the density of steel and b is the width of the beam. Hence at x = 0: (1/R)0 = ρgl2bh/(2EI).

Also I = ∫−h/2h/2 z2b dz = bh3/12. Hence (1/R)0 = 6ρgl2/(Eh2), i.e. R = Eh2/(6ρgl2) ≈ 0.12 km, as the book gives: 1/R = (0.121 km)−1.

Teacher's Note: Bending moment at the wall from the beam's own weight equals EI/R; rectangular I = bh³/12.

Exam Note: Cite EI/R = N and I = bh³/12.

Question 301. The bending of an elastic rod is described by the elastic curve passing through centres of gravity of the rod's cross-sections. At small bendings the equation of this curve takes the form N(x) = EI d2y/dx2, where N(x) is the bending moment of the elastic forces in the cross-section corresponding to the x coordinate, E is Young's modulus, I is the moment of inertia of the cross-section relative to the axis passing through the neutral layer (I = ∫z2dS, Fig. 1.75).
Suppose one end of a steel rod of a square cross-section with side a is embedded into a wall, the protruding section being of length l (Fig. 1.76). Assuming the mass of the rod to be negligible, find the shape of the elastic curve and the deflection of the rod λ, if its end A experiences
(a) the bending moment of the couple N0;
(b) a force F oriented along the y axis.
(Fig. 1.76: rod clamped at O, x axis along the rod, y axis downward, free end A deflected by λ.)

Solution. For small y, 1/R ≈ d2y/dx2, so d2y/dx2 = N(x)/EI.

(a) Here N(x) = N0 is a constant. Integrating, dy/dx = N0x/EI + C1. But dy/dx = 0 for x = 0, so C1 = 0. Integrating again and using y = 0 at x = 0: y = N0x2/(2EI). This is the equation of a parabola. The sag of the free end is λ = y(x = l) = N0l2/(2EI).

(b) In this case N(x) = F(l − x), because the load F at the extremity is balanced by a similar force F directed upward and they constitute a couple. Then d2y/dx2 = F(l − x)/EI. Integrating, dy/dx = F(lx − x2/2)/EI + C1, and as before C1 = 0. Integrating again with y = 0 at x = 0:

y = F(lx2/2 − x3/6)/EI, and λ = Fl3/(3EI).

For a square cross-section I = ∫−a/2a/2 z2a dz = a4/12. So (a) λ = 6N0l2/(Ea4) and (b) λ = 4Fl3/(Ea4).

Teacher's Note: Integrate EI y″ = N(x) twice with y = y′ = 0 at wall; couple gives parabola, force gives cubic.

Exam Note: Always state boundary conditions at the wall.

Question 302. A steel girder of length l rests freely on two supports (Fig. 1.77). The moment of inertia of its cross-section is equal to I (see the foregoing problem). Neglecting the mass of the girder and assuming the sagging to be slight, find the deflection λ due to the force F applied to the middle of the girder.
(Fig. 1.77: girder on two end supports with a downward force F at its midpoint.)

Solution. One can think of it as analogous to the previous case, but with a beam of length l/2 loaded upward by a force F/2 (each half behaves as a cantilever clamped at the middle).

Thus λ = Fl3/(48EI), on using the last result of the previous problem: (F/2)(l/2)3/(3EI) = Fl3/(48EI).

Teacher's Note: Midpoint slope is zero by symmetry, so each half acts as a cantilever of length l/2 with load F/2.

Exam Note: Use symmetry: cantilever l/2, force F/2.

Question 303. The thickness of a rectangular steel girder equals h. Using the equation of Problem 1.301, find the deflection λ caused by the weight of the girder in two cases:
(a) one end of the girder is embedded into a wall with the length of the protruding section being equal to l (Fig. 1.78a);
(b) the girder of length 2l rests freely on two supports (Fig. 1.78b).

Solution. (a) In this case N(x) = ½ρgbh(l − x)2, where b is the width of the girder. Also I = bh3/12. Then (Ebh3/12)·d2y/dx2 = (ρgbh/2)(l2 − 2lx + x2), i.e. d2y/dx2 = (6ρg/Eh2)(l − x)2.

Integrating, using dy/dx = 0 at x = 0: dy/dx = (6ρg/Eh2)(l2x − lx2 + x3/3). Again integrating: y = (6ρg/Eh2)(l2x2/2 − lx3/3 + x4/12).

Thus λ = (6ρgl4/Eh2)(1/2 − 1/3 + 1/12) = (6ρgl4/Eh2)(3/12) = 3ρgl4/(2Eh2).

(b) As before, EI d2y/dx2 = N(x), where N(x) is the bending moment due to the section PB. This bending moment is N = ∫x2l w(ξ − x)dξ − wl(2l − x) = w(2l2 − 2xl + x2/2) − wl(2l − x) = w(x2/2 − xl). (Here w = ρgbh is the weight of the beam per unit length.)

Integrating, EI dy/dx = w(x3/6 − x2l/2) + c0; since dy/dx = 0 for x = l, c0 = wl3/3. Integrating again, EIy = w(x4/24 − x3l/6) + wl3x/3 + c1. As y = 0 for x = 0, c1 = 0.

From this we find λ = y(x = l) = (5wl4/24)/EI = 5ρgl4/(2Eh2).

Teacher's Note: Distributed weight gives N ∝ (l−x)²; double integration with zero slope at the clamp or at mid-span.

Exam Note: Compare: (a) 3ρgl⁴/2Eh², (b) 5ρgl⁴/2Eh².

Question 304. A steel plate of thickness h has the shape of a square whose side equals l, with h ≪ l. The plate is rigidly fixed to a vertical axle OO which is rotated with a constant angular acceleration β (Fig. 1.79). Find the deflection λ, assuming the sagging to be small.
(Fig. 1.79: square plate attached along a vertical axle OO, its free edge deflected by λ.)

Solution. The deflection of the plate can be found by going to a co-rotating frame. In this frame each element of the plate experiences a pseudo force proportional to its mass. These forces have a moment which constitutes the bending moment of the problem. The acceleration of an element at a distance ξ from the axis is a = ξβ, and the moment of the forces exerted by the section between x and l is

N = ρlhβ ∫xl ξ2dξ = (1/3)ρlhβ(l3 − x3).

From the fundamental equation EI d2y/dx2 = (1/3)ρlhβ(l3 − x3). The moment of inertia I = ∫−h/2h/2 z2l dz = lh3/12. (The neutral surface is a vertical plane here and z is perpendicular to it.)

So d2y/dx2 = (4ρβ/Eh2)(l3 − x3). Integrating, dy/dx = (4ρβ/Eh2)(l3x − x4/4) + c1; since dy/dx = 0 at x = 0, c1 = 0. Integrating again, y = (4ρβ/Eh2)(l3x2/2 − x5/20) + c2, with c2 = 0 because y = 0 at x = 0.

Thus λ = y(x = l) = 9ρβl5/(5Eh2).

Teacher's Note: In the rotating frame, tangential inertial force ρξβ per volume bends the plate; here I = lh³/12.

Exam Note: Mention pseudo force and clamped boundary conditions.

Question 305. Determine the relationship between the torque N and the torsion angle φ for
(a) the tube whose wall thickness Δr is considerably less than the tube radius;
(b) the solid rod of circular cross-section.
Their length l, radius r, and shear modulus G are supposed to be known.

Solution. (a) Consider a hollow cylinder of length l, outer radius r + Δr, inner radius r, fixed at one end and twisted at the other by a couple of moment N. The angular displacement φ is proportional to both l and N. Consider an element of length dx at the twisted end, moved by an angle φ. The twisting of the parallelepiped of length l and area Δr dx can be discussed by elementary means. If f is the tangential force generated, the shearing stress is f/(Δr dx), and this must equal Gθ = G rφ/l, since θ = rφ/l.

Hence f = GΔr dx rφ/l. The force f has moment fr about the axis, so the total moment is

N = GΔr (φ/l) r2 ∫dx = 2πr3Δr φ G/l.

(b) For a solid cylinder we must integrate over r:

N = ∫0r (2πr3dr φG/l) = πr4Gφ/(2l).

Teacher's Note: Shear strain at radius r is rφ/l; torque from a thin shell is 2πr³ΔrGφ/l, integrate for solid rod.

Exam Note: Quote N = πGr⁴φ/2l for solid rod.

Question 306. Calculate the torque N twisting a steel tube of length l = 3.0 m through an angle φ = 2.0° about its axis, if the inside and outside diameters of the tube are equal to d1 = 30 mm and d2 = 50 mm.

Solution. Clearly N = ∫d1/2d2/2 (2πr3dr φG/l) = (π/32l) Gφ(d24 − d14).

Using G = 81 GPa = 8.1 × 1010 N/m2, d2 = 5 × 10−2 m, d1 = 3 × 10−2 m, φ = 2.0° = π/90 rad, l = 3 m:

N = [π × 8.1 × 1010 × π/(32 × 3 × 90)] × (625 − 81) × 10−8 N·m = 0.5033 × 103 N·m ≈ 0.5 kN·m.

Teacher's Note: Integrate the shell torque from inner to outer radius; convert degrees to radians and use fourth powers of diameters.

Exam Note: Convert φ to radians before substituting.

Question 307. Find the maximum power which can be transmitted by means of a steel shaft rotating about its axis with an angular velocity ω = 120 rad/s, if its length l = 200 cm, radius r = 1.50 cm, and the permissible torsion angle φ = 2.5°.

Solution. The maximum power that can be transmitted by a rotating shaft is clearly Nω, where N is the moment of the couple producing the maximum permissible torsion φ. Thus

P = (πr4Gφ/2l)·ω = 16.9 kW.

Teacher's Note: Power is torque times angular velocity; torque comes from the permitted twist N = πGr⁴φ/2l.

Exam Note: Use P = Nω with φ in radians.

Question 308. A uniform ring of mass m, with the outside radius r2, is fitted tightly on a shaft of radius r1. The shaft is rotated about its axis with a constant angular acceleration β. Find the moment of elastic forces in the ring as a function of the distance r from the rotation axis.

Solution. Consider an elementary ring of width dr at a distance r from the axis. The part outside exerts a couple (N + (dN/dr)dr) on this ring while the part inside exerts a couple N in the opposite direction. For equilibrium (dN/dr)dr = −dI·β, where dI is the moment of inertia of the elementary ring, β is the angular acceleration, and the minus sign is needed because the couple N(r) decreases with distance, vanishing at the outer radius, N(r2) = 0. Now

dI = [m/(π(r22 − r12))]·2πr dr·r2.

Thus dN = −[2mβ/(r22 − r12)] r3dr, or on integration

N = (1/2)·mβ/(r22 − r12)·(r24 − r4).

Teacher's Note: Net torque on a thin ring element equals its moment of inertia times β; integrate inward from N(r₂)=0.

Exam Note: Boundary condition: N = 0 at outer radius.

Question 309. Find the elastic deformation energy of a steel rod of mass m = 3.1 kg stretched to a tensile strain ε = 1.0·10−3.

Solution. We assume that the deformation is wholly due to the external load, neglecting the weight of the rod (see next problem). Then the elastic energy per unit volume = ½ × stress × strain = ½σε.

This gives the total deformation energy U = (1/2)(m/ρ)Eε2 ≈ 0.04 kJ.

Teacher's Note: Energy density ½Eε² times volume m/ρ; no length or area needed.

Exam Note: Substitute V = m/ρ and write the unit as J.

Question 310. A steel cylindrical rod of length l and radius r is suspended by its end from the ceiling.
(a) Find the elastic deformation energy U of the rod.
(b) Define U in terms of the tensile strain Δl/l of the rod.

Solution. When a rod is deformed by its own weight the stress increases as one moves up, the stretching force being the weight of the portion below the element considered. Measuring x downward from the ceiling, the stress on the element dx is ρπr2(l − x)g/πr2 = ρg(l − x).

The extension of the element is d(Δx) = ρg(l − x)dx/E. Integrating, Δl = ρgl2/(2E) is the extension of the whole rod. The elastic energy of the element is ½ρg(l − x)·[ρg(l − x)/E]·πr2dx.

Integrating, (a) U = πr2ρ2g2l3/(6E);

(b) U = (2/3)πr2lE(Δl/l)2.

Teacher's Note: Stress varies with position, so integrate ½σ·strain·volume over the rod; compare with uniform case ½πr²lE(Δl/l)².

Exam Note: Give U in both forms; note factor 2/3.

Question 311. What work has to be performed to make a hoop out of a steel band of length l = 2.0 m, width h = 6.0 cm, and thickness δ = 2.0 mm? The process is assumed to proceed within the elasticity range of the material.

Solution. The work done to make a loop out of a steel band appears as the elastic energy of the loop. If the length of the band is l, the radius of the loop is R = l/2π. Consider an element ABCD of the loop and a fibre at a distance z from the neutral surface PQ. The fibre undergoes an extension ds = z dφ, while PQ = s = R dφ. Thus the strain ds/s = z/R. If α is the cross-sectional area of the fibre, the elastic energy associated with it is ½E(z/R)2R dφ α.

Summing over all the fibres, with I = Σαz2, the energy of the element is EI dφ/(2R). For the whole loop, using ∫dφ = 2π: EIπ/R = 2π2EI/l.

Now I = ∫−δ/2δ/2 z2h dz = hδ3/12. So the energy is (1/6)π2Ehδ3/l ≈ 0.08 kJ.

Teacher's Note: Bending energy of the band is ∫½E(z/R)² dV; with I = hδ³/12 and R = l/2π.

Exam Note: Show R = l/2π and I = hδ³/12.

Question 312. Find the elastic deformation energy of a steel rod whose one end is fixed and the other is twisted through an angle φ = 6.0°. The length of the rod is equal to l = 1.0 m, and the radius to r = 10 mm.

Solution. When the rod is twisted through an angle θ a couple N(θ) = πr4Gθ/(2l) appears to resist this. The work done in twisting the rod by an angle φ is then

∫0φ N(θ)dθ = πr4Gφ2/(4l) = 7 J on putting the values.

Teacher's Note: Torque grows linearly with twist, so work is ½Nφ; use φ in radians.

Exam Note: Convert 6° to radians; answer ≈ 7 J.

Question 313. Find how the volume density of the elastic deformation energy is distributed in a steel rod depending on the distance r from its axis. The length of the rod is equal to l, the torsion angle to φ.

Solution. The energy between radii r and r + dr is, by differentiation, (πr3dr/l)Gφ2. Its density is

(πr3dr Gφ2)/(2πr dr l · l) = ½Gφ2r2/l2.

Teacher's Note: Shear strain rφ/l grows with r, so energy density ½G(rφ/l)² grows as r²; zero on the axis.

Exam Note: State density ∝ r² and maximum at surface.

Question 314. Find the volume density of the elastic deformation energy in fresh water at the depth of h = 1000 m.

Solution. The energy density is as usual ½ × stress × strain. Stress is the pressure p = ρgh. Strain is β × ρgh by definition of β. Thus

u = ½β(ρgh)2 = 23.5 kJ/m3 on putting the values.

Teacher's Note: Energy density = ½ × pressure × volumetric strain, with strain = βp from compressibility.

Exam Note: Use β of water; answer about 23 kJ/m³.

Download IE Irodov Solutions for JEE Math PDF

Access JEE Mathematics Solutions

Explore reliable mathematical solutions for IE Irodov Solutions Chapter 6 Elastic Deformations Of A Solid Body tailored for JEE learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.

Step-by-Step Mathematical Explanations

Beyond providing the final numerical answer, these guides break down the underlying mathematical principles. Cross-referencing completed work with these structured explanations helps eliminate calculation errors and reinforces conceptual clarity.

Additional Study Materials for 2026

Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.

FAQs

What are these IE Irodov Solutions for JEE Physics?

They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.

Are the IE Irodov JEE Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these IE Irodov solutions for JEE Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising IE Irodov JEE Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these JEE Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.