SB Mathur Physics Solutions Chapter 1 Multiple-Choice Questions Type 1 Part 1

Official SB Mathur Textbook Solutions: JEE Physics Chapter 01 Multiple-Choice Questions Type 1

Review structured textbook solutions for JEE Physics Chapter 01 Multiple-Choice Questions Type 1 prepared by SB Mathur. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.

Chapter-wise Solutions for Physics: Chapter 01 Multiple-Choice Questions Type 1

Access the complete solution PDF for JEE Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.

Chapter 1 Multiple-Choice Questions: Type 1 - Part 1 (1.1 General Physics to 1.4 Electrostatics Q6)

1.1 General Physics

Question 1.1.1. A vernier callipers has 1-mm marks on the main scale. It has 20 equal divisions on the vernier scale which match with 16 main-scale divisions. For this vernier callipers, the least count is
(a) 0.02 mm   (b) 0.05 mm   (c) 0.1 mm   (d) 0.2 mm

Solution. LC = 1 MSD − 1 VSD = 1 mm − (16/20) mm = 0.2 mm. Answer: (d) 0.2 mm.

Teacher's Note: Least count equals one MSD minus one VSD; find VSD from the matching divisions.

Exam Note: Two lines: VSD value, then subtraction.

Question 1.1.2. A quantity X is given by ε0 L (ΔV/Δt), where ε0 is the permittivity of vacuum, L is the length, ΔV is the potential difference and Δt is the time interval. The dimensional formula for X is the same as that for
(a) resistance   (b) charge   (c) voltage   (d) current

Solution. V = (1/4πε0)·(Q/L), so [ε0LV] = [Q]. Hence [X] = [ε0LΔV/Δt] = [Q/Δt] = [current]. Answer: (d) current.

Teacher's Note: Use the Coulomb potential formula to get ε0LV as charge, then divide by time.

Exam Note: Show ε0LV = Q to earn the mark.

Question 1.1.3. The density of a solid ball is to be determined in an experiment. The diameter of the ball is measured with a screw gauge whose pitch is 0.5 mm, with 50 divisions on the circular scale. The reading on the main scale is 2.5 mm and that on the circular scale is 20 divisions. If the measured mass of this ball has a relative error of 2%, the relative percentage error in the density is
(a) 0.9   (b) 2.4   (c) 3.1   (d) 4.2

Solution. Diameter = 2.5 mm + (0.5 mm/50) × 20 = 2.7 mm. Density ∝ m/r3, so percentage error in density = (dm/m + 3dr/r) × 100 = 2 + (3 × 0.01/2.70) × 100 = 3.1. Answer: (c) 3.1.

Teacher's Note: Density has diameter cubed, so its relative error is tripled; least count is 0.01 mm.

Exam Note: Remember the factor 3 for the cubed quantity.

Question 1.1.4. In the determination of Young modulus (Y = 4MgL/πd2l) by using Searle’s method, a wire of length L = 2 m and diameter d = 0.5 mm is used. For a load M = 2.5 kg, an extension l = 0.25 mm in the length of the wire is observed. Quantities d and l are measured using a screw gauge and a micrometer respectively. They have equal pitches of 0.5 mm. The number of divisions on each of their circular scales is 100. The maximum probable error in the measurement of Y arises due to the error in l and d both.
(a) The error in the measurement of d and l are equal.
(b) The error in the measurement of d is twice the error in the measurement of l.
(c) The error in the measurement of l is twice the error in the measurement of d.
(d) The error in the measurement of d is four times the error in the measurement of l.

Solution. Δd = Δl = least count = pitch/(number of divisions) = 0.5 mm/100. Then ΔY/Y = Δl/l + 2(Δd/d) = (0.5 mm/100)/(0.25 mm) + 2·(0.5 mm/100)/(0.5 mm) = (0.5 × 10−2)/0.25 + (0.5 × 10−2)/0.25. Hence the errors in the measurement of d and l are equal. Answer: (a).

Teacher's Note: Same pitch and same divisions give the same absolute error in d and l.

Exam Note: Compare absolute errors, not relative errors.

Question 1.1.5. During an experiment with a metre bridge, the galvanometer shows a null point when the jockey is pressed at 40.0 cm using a standard resistance (R) of 90 Ω, as shown in the figure. The least count of the scale used in the metre bridge is 1 mm. The unknown resistance (X) is
(Figure: metre bridge with the unknown resistance X in the left gap and the 90 Ω resistance in the right gap; the null point is at 40 cm from the left end.)
(a) (60 ± 0.15) Ω   (b) (135 ± 0.56) Ω   (c) (60 ± 0.25) Ω   (d) (135 ± 0.23) Ω

Solution. For balance, X/R = l/(100 cm − l) = 40/60, so X = (40/60) × 90 Ω = 60 Ω. Now X = R·l/(100 − l), so ΔX/X = Δl/l + Δl/(100 − l) = 0.1/40 + 0.1/60 = 1/240. Hence ΔX = (1/240) × 60 Ω = 0.25 Ω and X = (60 ± 0.25) Ω. Answer: (c).

Teacher's Note: Balance condition gives X; errors from l and (100 − l) add.

Exam Note: Include the error calculation, not just 60 Ω.

Question 1.1.6. The diameter of a cylinder is measured using a vernier callipers with no zero errors. It is found that the zero of the vernier scale lies between 5.10 cm and 5.15 cm of the main scale. The vernier scale has 50 divisions, equivalent to 2.45 cm. The 24th division of the vernier scale exactly coincides with one of the main-scale divisions. The diameter of the cylinder is
(a) 5.112 cm   (b) 5.124 cm   (c) 5.136 cm   (d) 5.148 cm

Solution. MSD = 0.05 cm and VSD = 2.45 cm/50 = 0.049 cm. LC = 1 MSD − 1 VSD = 0.05 − 0.049 = 0.001 cm. Diameter = MS + VC × LC = 5.10 + 24 × 0.001 = 5.124 cm. Answer: (b) 5.124 cm.

Teacher's Note: Find MSD and VSD first, then least count, then add coinciding division times LC.

Exam Note: Write LC = 0.001 cm explicitly.

Question 1.1.7. There are two vernier callipers, both of which have 1 cm divided into 10 equal divisions on the main scale. The vernier scale of one of the callipers (C1) has 10 equal divisions, corresponding to 9 main-scale divisions. The vernier scale of the other calliper (C2) has 10 equal divisions that correspond to 11 main-scale divisions. The readings of the two callipers are shown in the figure. The measured values by the callipers C1 and C2 are respectively
(Figure: two vernier scales against a main scale marked 2, 3, 4 cm; in C1 the vernier zero lies just past 2.8 cm, in C2 the vernier zero lies just past 2.8 cm with the vernier extending beyond.)
(a) 2.87 cm and 2.86 cm   (b) 2.87 cm and 2.87 cm   (c) 2.87 cm and 2.83 cm   (d) 2.85 cm and 2.82 cm

Solution. For C1: MSD reading = 2.8 cm and VSD coincidence × LC = 7 × (1/10) mm = 0.07 cm, so the reading is 2.87 cm. For C2: MSD reading = 2.8 cm and vernier reading = 7 × (−0.1/10) cm = −0.07 cm, so the reading is 2.80 + 0.10 − 0.07 = 2.83 cm. Answer: (c) 2.87 cm and 2.83 cm.

Teacher's Note: C2 has negative least count (−0.1 mm), so the vernier reading is subtracted.

Exam Note: Spot the negative least count of C2.

Question 1.1.8. Consider an expanding sphere of instantaneous radius R whose mass (M) remains constant. The expansion is such that the instantaneous density (ρ) remains uniform throughout the volume. The rate of fractional change in density ((1/ρ)(dρ/dt)) is also constant. The velocity (v) of any point on the surface of the expanding sphere is proportional to
(a) R2/3   (b) R   (c) R3   (d) 1/R

Solution. M = (4/3)πR3ρ = constant ⇒ (4/3)π·3R2(dR/dt)ρ + (4/3)πR3(dρ/dt) = 0 ⇒ dR/dt = −(R/3ρ)(dρ/dt). Since (1/ρ)(dρ/dt) is constant, v ∝ R. Answer: (b) R.

Teacher's Note: Differentiate M = (4/3)πR3ρ; constant fractional rate makes v proportional to R.

Exam Note: Differentiate the constant-mass relation.

Question 1.1.9. A person measures the depth of a well by measuring the time interval between dropping a stone and receiving the sound of impact of the stone with the bottom of the well. The error in his measurement of time is δT = 0.01 second, and he measures the depth of the well (L) to be 20 metres. Take the acceleration due to gravity (g) as 10 m s−2 and the velocity of sound as 300 m s−1. Then the fractional error (δL/L) in the measurement is close to
(a) 0.2%   (b) 5%   (c) 1%   (d) 3%

Solution. T = √(2L/g) + L/v ⇒ δT/δL = 1/√(2gL) + 1/v. Therefore δL = δT/(1/20 + 1/300) = (150/8)δT = 18.75 × 0.01 m = 0.1875 m, so δL/L = 0.1875/20 ≈ 0.94% ≈ 1%. Answer: (c) 1%.

Teacher's Note: Total time is fall time plus sound time; differentiate with respect to L.

Exam Note: Final answer is about 1%.

Question 1.1.10. Three vectors P, Q and R are shown in the figure. Let S be a point on the vector R. The distance between the points P and S is b|R|. The general relation among P, Q and S is
(Figure: position vectors P and Q from the origin O to points P and Q; R = Q − P is the vector from P to Q; S is a point on PQ at distance b|R| from P.)
(a) S = (1 − b)P + b2Q   (b) S = (1 − b2)P + bQ   (c) S = (1 − b)P + bQ   (d) S = (b − 1)P + bQ

Solution. S = P + b|R| (taking the vector R) = P + b(Q − P) = P(1 − b) + bQ. Answer: (c).

Teacher's Note: S is P plus the fraction b of the vector from P to Q.

Exam Note: Write S = P + bR first.

Question 1.1.11. A ball is dropped vertically from a height d above the ground. It hits the ground and bounces up vertically to a height d/2. Neglecting the subsequent motion and the air resistance, how its velocity (v) varies with the height (h) above the ground?
(Figure: four v–h graphs. (a) an arc in the upper half-plane (positive v) from the v-axis down to h = d/2 and an arc in the lower half-plane (negative v) reaching h = d; (b) two arcs both in the upper half-plane; (c) two straight lines, one above and one below the h-axis; (d) two arcs both below the h-axis.)

Solution. v is negative when the ball is falling and positive when it bounces up. Also, v = −√(2g(d − h)) for downward motion and v = √(g(d − 2h)) for upward motion. These are elliptical (parabola-type v2–h) curves: the downward branch reaches h = d and the upward branch reaches h = d/2. Answer: (a).

Teacher's Note: Energy conservation gives v2 linear in h, so v–h is an arc; sign shows direction.

Exam Note: Negative v on the way down, positive on the way up.

Question 1.1.12. Two identical discs of the same radius R are rotating about their axes in opposite directions at the same angular speed ω. The discs are in the same horizontal plane. At the time t = 0, the points P and Q are facing each other, as shown in the figure. The relative speed between the two points P and Q is vr. In each period of rotation (T) of the discs, vr as a function of time is best represented by
(Figure: four vr–t graphs over one period T. (a) two arches that touch zero at t = 0, T/2 and T; (b) arches that start from a non-zero value at t = 0; (c) four arches touching zero; (d) four arches starting from non-zero value.)

Solution. Relative velocity = |vr| = 2v sin θ = 2v sin ωt. In each rotation the relative speed becomes zero twice and reaches the maximum value twice. Answer: (a).

Teacher's Note: Components along the line joining the points cancel; relative speed is 2v sin ωt.

Exam Note: Zero at t = 0, T/2, T; two arches per period.

Question 1.1.13. A string of negligible mass going over a clamped pulley of mass m supports a block of mass M, as shown in the figure. The force on the pulley by the clamp is given by
(Figure: pulley fixed to a wall by a clamp; the string passes over it, one end horizontal and attached to the wall, the other end hanging vertically with block M.)
(a) √2 Mg   (b) √2 mg   (c) √((M + m)2 + m2)·g   (d) √((M + m)2 + M2)·g

Solution. For the block of mass M to be in equilibrium, the tension in the string is T = Mg. The force on the pulley by the clamp must balance all the other forces acting on it: the vertical forces Mg (down, string) + mg (weight) and the horizontal pull T = Mg. Its magnitude is √((Mg + mg)2 + (Mg)2) = g√((M + m)2 + M2). Answer: (d).

Teacher's Note: Clamp force balances weight, vertical string pull and horizontal string pull on the pulley.

Exam Note: Add vertical and horizontal parts as vectors.

Question 1.1.14. Two particles of masses m1 and m2 in projectile motion have the velocities v1 and v2 respectively at the time t = 0. They collide at t = t0. Their velocities become v1′ and v2′ at t = 2t0 while still moving in air. The value of |(m1v1′ + m2v2′) − (m1v1 + m2v2)| is
(a) zero   (b) (m1 + m2)gt0   (c) 2(m1 + m2)gt0   (d) ½(m1 + m2)gt0

Solution. The momentum of the two-particle system at t = 0 is pi = m1v1 + m2v2. A collision between the two does not affect the total momentum of the system. A constant external force (m1 + m2)g acts on the system. The impulse given by this force from t = 0 to t = 2t0 is (m1 + m2)g × 2t0. Hence the absolute change in momentum is 2(m1 + m2)gt0. Answer: (c).

Teacher's Note: Internal collision forces cancel; only gravity changes total momentum, over time 2t0.

Exam Note: Use the full interval 2t0, not t0.

Question 1.1.15. A small block is shot into each of the four tracks shown below. Each of the tracks rises to the same height. The speed with which the block enters the track is the same in all cases. At the highest point of the track, the normal reaction is the maximum in the case
(Figure: four curved tracks (a)–(d) starting horizontally and curving upward to the same height; the track in (a) bends most sharply at the top (smallest radius of curvature) and the curvature becomes gentler from (a) to (d).)

Solution. The blocks have the same speed, say v, at the highest point of each track, as they all rise to the same height. Let R be the radius of curvature of a track and N the normal reaction of the track at the highest point. Centripetal force = N + mg = mv2/R. N is maximum when R is minimum, which occurs when the track is most sharply curved. Answer: (a).

Teacher's Note: Same speed at the top, so N = mv2/R − mg is largest for smallest radius.

Exam Note: State N + mg = mv2/R at the top.

Question 1.1.16. A long horizontal rod has a bead which can slide along its length and is initially placed at a distance L from one end A of the rod. The rod is set in angular motion about A with a constant angular acceleration α. If the coefficient of friction between the rod and the bead is μ and the gravity is neglected, the time after which the bead starts slipping is
(a) √(μ/α)   (b) μ/√α   (c) 1/√(μα)   (d) infinitesimal

Solution. The linear acceleration of the bead is a = Lα, so the reaction force on the bead due to the rod is N = ma = mLα. After the time t, the angular velocity is ω = αt, so the centripetal acceleration is ω2L = α2t2L. The force of friction at the limiting position is μN = μmLα. For slipping, μmLα = mα2t2L, i.e. t = √(μ/α). Answer: (a).

Teacher's Note: Normal force comes from tangential acceleration; friction must supply the growing centripetal force.

Exam Note: Equate μN to mω2L at limit.

Question 1.1.17. A cubical block of side length L rests on a rough horizontal surface having the coefficient of friction μ. A horizontal force F is applied on the block, as shown. If the coefficient of friction is sufficiently high so that the block does not slide before toppling, the minimum force required to topple the block is
(a) infinitesimal   (b) mg/4   (c) mg/2   (d) mg(1 − μ)

Solution. When F is applied at the top face, the normal reaction N moves to the right; the cube topples when N reaches its edge. Here N = mg and the force of friction is f = F. Taking the torque about the centre C, F × L/2 + f × L/2 = N × L/2, or 2F = mg. Answer: (c) mg/2.

Teacher's Note: At toppling the normal force acts at the edge; torque about the centre gives F.

Exam Note: Friction equals F, so both forces contribute torque.

Question 1.1.18. A block of mass m is on an inclined plane of angle θ. The coefficient of friction between the block and the plane is μ, where tan θ > μ. The block is held stationary by applying a force P parallel to the plane. The direction of force pointing up the plane is taken to be positive. As P is varied from P1 = mg(sin θ − μ cos θ) to P2 = mg(sin θ + μ cos θ), the frictional force f versus P graph will look like
(Figure: four f–P graphs between P1 and P2. (a) a straight line falling from a positive value at P1 to a negative value at P2; (b) constant positive value; (c) a straight line rising from negative to positive; (d) constant negative value.)

Solution. The force of friction f becomes zero when P = mg sin θ. For P < mg sin θ, f acts upwards along the incline (positive); for P > mg sin θ it acts down the incline. So f = mg sin θ − P falls linearly from +μmg cos θ at P1 to −μmg cos θ at P2. Answer: (a).

Teacher's Note: Equilibrium along the plane gives f = mg sin θ − P, a falling straight line.

Exam Note: Sign of f flips at P = mg sin θ.

Question 1.1.19. A uniform wooden stick of mass 1.6 kg and length l rests in an inclined manner on a smooth vertical wall of height h (< l) such that a small portion of the stick extends beyond the wall. The reaction force of the wall on the stick is perpendicular to the stick. The stick makes an angle of 30° with the wall, and the bottom of the stick is on a rough floor. The reaction of the wall on the stick is equal in magnitude to the reaction of the floor on the stick. The ratio h/l and the frictional force f at the bottom of the stick are respectively (when g = 10 m s−2)
(a) √3/16 and 16√3/3 N   (b) 3/16 and 16√3/3 N   (c) 3√3/16 and 8√3/3 N   (d) 3√3/16 and 16√3/3 N

Solution. Taking the torque about the bottom A: N(h/sin 60°) = mg(l/2) cos 60°, so (2/√3)Nh = ¼ mgl …(i). Also the vertical balance gives N + N cos 60° = mg, so (3/2)N = mg and N = (2/3)mg. Substituting in (i): (2/√3)(2/3)mgh = ¼ mgl, so h/l = 3√3/16. Friction f = N sin 60° = (2/3)mg·(√3/2) = mg/√3 = 16√3/3 N (with m = 1.6 kg, g = 10). Answer: (d).

Teacher's Note: Torque about the foot and vertical force balance give N, then h/l; friction balances N sin 60°.

Exam Note: Wall reaction is perpendicular to the stick.

Question 1.1.20. A simple pendulum is oscillating without damping. When the displacement of the bob is less than the maximum, its acceleration vector a is correctly shown in the figure
(Figure: four pendulum diagrams (a)–(d) showing the acceleration vector at the bob: (a) along the string towards the pivot; (b) along the string pointing away from the pivot; (c) pointing towards the pivot side, between the string direction and the tangent; (d) vertically downward.)

Solution. In the given position, the bob is moving along a circular path with some speed and hence has some radial acceleration ar (towards the pivot). It also has some tangential acceleration at. As a is the resultant of these two, it will be directed somewhere between them. Answer: (c).

Teacher's Note: Acceleration is the vector sum of radial (centripetal) and tangential parts.

Exam Note: Not purely radial except at the lowest point.

Question 1.1.21. A cylinder rolls up an inclined plane, reaches some height, and then rolls down (without slipping throughout these motions). The directions of the frictional force acting on the cylinder are
(a) up the incline while ascending and down the incline while descending
(b) up the incline while ascending as well as descending
(c) down the incline while ascending and up the incline while descending
(d) down the incline while ascending as well as descending

Solution. When the cylinder rolls up the incline, its angular velocity ω is clockwise and decreasing. This requires an anticlockwise angular acceleration α, which is provided by the force of friction (F) acting up the incline. When the cylinder rolls down the incline, its angular velocity ω is anticlockwise and increasing. This requires an anticlockwise angular acceleration α, which is provided by the force of friction (F) acting up the incline. Answer: (b).

Teacher's Note: Friction supplies the torque; in both phases the needed angular acceleration has the same sense.

Exam Note: Friction is up the incline in both cases.

Question 1.1.22. A circular platform is free to rotate in a horizontal plane about a vertical axis passing through its centre. A tortoise is sitting at the edge of the platform. Now, the platform is given an angular velocity ω0. When the tortoise moves along a chord of the platform with a constant velocity (with respect to the platform), the angular velocity of the platform ω(t) will vary with time t as
(Figure: four ω(t) graphs starting at ω0. (a) horizontal line; (b) smooth curve that rises above ω0 and then falls; (c) smooth curve that falls below ω0 and then rises; (d) straight line rising then straight line falling.)

Solution. The angular momentum (L) of the system is conserved; i.e., Iω = constant. When the tortoise walks along a chord, it first moves closer to the centre and then away from the centre. Hence I first decreases and then increases. As a result, ω will first increase and then decrease. Also, the change in ω will be a nonlinear function of time. Answer: (b).

Teacher's Note: Angular momentum is conserved; moment of inertia first falls then rises along the chord.

Exam Note: Distance from the centre is nonlinear in t.

Question 1.1.23. A ball of mass m = 0.5 kg is attached to the end of a string of length L = 0.5 m. The ball is rotated on a horizontal circular path about the vertical axis. The maximum tension that the string can bear is 324 N. The maximum possible value of the angular velocity of the ball is
(a) 9 rad s−1   (b) 18 rad s−1   (c) 27 rad s−1   (d) 36 rad s−1

Solution. A centripetal force is provided by the component of the tension along the horizontal. So T sin θ = mω2r = mω2(L sin θ), giving T = mω2L, hence ω = √(T/mL) = √(324 N/((0.5 kg)(0.5 m))) = √1296 = 36 rad s−1. Answer: (d).

Teacher's Note: Horizontal component of tension gives T = mω2L independent of the cone angle.

Exam Note: Radius is L sin θ, so θ cancels.

Question 1.1.24. The work done on a particle of mass m by a force K{x/(x2 + y2)3/2 i + y/(x2 + y2)3/2 j} when the particle is taken from the point (a, 0) to another point (0, a) along a circular path of radius a about the origin in the xy-plane is
(a) 2πK/a   (b) πK/a   (c) πK/2a   (d) 0

Solution. Work done = ∫F·dr = ∫F·(dx i + dy j) = (K/a3)∫a0 x dx + (K/a3)∫0a y dy [since x2 + y2 = a2] = (K/a3)(−a2/2 + a2/2) = 0. [Note: F = (K/a3)(xi + yj) = (K/a3)r (radial). Any radial force does zero work in circular motion.] Answer: (d) 0.

Teacher's Note: Force is radial, hence perpendicular to the circular displacement; work is zero.

Exam Note: Spot the radial force before integrating.

Question 1.1.25. A wire which passes through the hole in a small bead is bent in the form of a quarter of a circle. The wire is fixed vertically on the ground, as shown in the figure. The bead is released from near the top of this wire and it slides along the wire without friction. As the bead moves from A to B, the force it applies on the wire is
(Figure: a quarter circle of 90° with A at the top and B on the ground at the right end; the wire is fixed vertically with its centre at the foot.)
(a) always radially outwards
(b) always radially inwards
(c) initially radially outwards and later radially inwards
(d) initially radially inwards and later radially outwards

Solution. For energy conservation, ½mv2 = mgR(1 − cos θ), and for circular motion, mg cos θ − N = mv2/R. Simplifying, N = mg(3 cos θ − 2). Initially, θ = 0, i.e. N = mg (radially inward on the wire). As θ increases, N decreases. At θ = cos−1(2/3) ≈ 48°, N reduces to zero, and afterwards N acts radially outward. Answer: (d).

Teacher's Note: N = mg(3cos θ − 2) changes sign at cos θ = 2/3.

Exam Note: Find the angle where N becomes zero.

Question 1.1.26. A block of mass 2 kg is free to move along the x-axis. It is at rest and from t = 0 onwards it is subjected to a time-dependent force F(t) in the x-direction. The force F(t) varies with t as shown in the figure above. The kinetic energy of the block after 4.5 seconds is
(Figure: F–t graph, a straight line falling from F = 4 N at t = 0 through zero at t = 3 s to a negative value at t = 4.5 s.)
(a) 4.50 J   (b) 7.50 J   (c) 5.06 J   (d) 14.06 J

Solution. The area under the F–t curve is 4.5 kg m s−1 = p (positive area ½·3·4 = 6, negative area ½·1.5·2 = −1.5). Hence KE = p2/2m = 4.52/(2 × 2) = 5.06 J. Answer: (c) 5.06 J.

Teacher's Note: Impulse equals area under F–t; kinetic energy follows from momentum, KE = p2/2m.

Exam Note: Subtract the negative area after 3 s.

Question 1.1.27. A moving point mass of 1 kg collides elastically with a stationary point mass of 5 kg. After their collision, the 1-kg mass reverses its direction and moves with a speed of 2 m s−1. Which of the following statement is correct for the system of these two masses?
(a) The total momentum of the system is 4 kg m s−1.
(b) The momentum of the 5-kg mass after collision is 4 kg m s−1.
(c) The kinetic energy of the centre of mass is 0.75 J.
(d) The total kinetic energy of the system is 4 J.

Solution. Momentum conservation: u = −2 m s−1 + 5v. Elastic collision: v + 2 m s−1 = −1(0 − u) = u. Solving, u = 3 m s−1 and v = 1 m s−1. Total momentum = 3 kg m s−1; the 5-kg mass has 5 kg m s−1; total KE = ½(1)(3)2 = 4.5 J. KE of CM = ½(6 kg)(0.5 m s−1)2 = 0.75 J. Answer: (c).

Teacher's Note: Use momentum conservation plus relative-speed reversal to get u = 3 m s−1.

Exam Note: Check every option against u and v.

Question 1.1.28. A ball of mass 0.2 kg rests on a vertical post of height 5 m. A bullet of mass 0.01 kg, travelling with a velocity v m s−1 in a horizontal direction, hits the centre of the ball. After the collision, the ball and the bullet travel independently. The ball hits the ground at a distance of 20 m and the bullet, at a distance of 100 m from the foot of the post. The velocity v of this bullet is
(a) 250 m s−1   (b) 250√2 m s−1   (c) 400 m s−1   (d) 500 m s−1

Solution. h = ½gt2 ⇒ 5 = ½(10)t2 ⇒ t = 1 s. From x = vxt we have vball = 20 m s−1 and vbullet = 100 m s−1. Conserving linear momentum, 0.01v = 0.01 × 100 + 0.2 × 20 ⇒ v = 500 m s−1. Answer: (d).

Teacher's Note: Same fall time gives both horizontal speeds; then conserve horizontal momentum.

Exam Note: Both fall 5 m in 1 s.

Question 1.1.29. A particle of mass m is projected from the ground with an initial speed u0 at an angle α with the horizontal. At the highest point of its trajectory, it makes a perfectly inelastic collision with another identical particle, which was thrown vertically upward from the ground with the same initial speed (u0). The angle that the composite system makes with the horizontal immediately after the collision is
(a) π/4   (b) π/4 + α   (c) π/4 − α   (d) π/2

Solution. At the highest point, the velocity of the 1st particle is v1 = (u0 cos α) i. At the position of collision (H = u02 sin2α/2g), the velocity of the 2nd particle is v2 = √(u02 − 2gH) j = √(u02 − u02 sin2α) j = (u0 cos α) j. Conserving linear momentum, 2mv = mv1 + mv2 = m(u0 cos α)(i + j) ⇒ v = (u0 cos α/2)(i + j), so θ = 45°. Answer: (a) π/4.

Teacher's Note: Both particles have speed u0 cos α at the collision point, one horizontal, one vertical.

Exam Note: Equal perpendicular components give 45°.

Question 1.1.30. A tennis ball is dropped on a smooth horizontal surface. It bounces back to its original position after hitting the surface. The force on the ball during the collision is proportional to the length of compression of the ball. Which one of the following sketches describes the variation of its kinetic energy K with the time t most appreciably? (The figures are only illustrative and not drawn to the scale.)
(Figure: four K–t graphs. (a) smooth arcs with a dip to zero in the middle; (b) K rises from zero to a peak, falls to zero, rises to a second peak and falls back to zero, with convex (cusp-like) sections; (c) a flat plateau between rising and falling parts; (d) straight rising and falling lines with a dip to zero.)

Solution. Kinetic energy K = ½mv2, so dK/dt = ½m(2v·dv/dt) = mv·dv/dt = F·v. During free fall K increases as the ball speeds up; during compression the force grows with compression, K falls to zero at maximum compression and then rises again as the ball rebounds, and K falls to zero at the top. Hence K–t has the two-peak form shown in (b). Answer (from key): (b).

Teacher's Note: dK/dt = Fv: K changes continuously, falling to zero at maximum compression.

Exam Note: Link slope of K to force times velocity.

Question 1.1.31. Two blocks of masses 10 kg and 4 kg are connected by a spring of negligible mass and placed on a frictionless horizontal surface. An impulse gives a velocity of 14 m s−1 to the heavier block in the direction of the lighter block. The velocity of the centre of mass is
(a) 30 m s−1   (b) 20 m s−1   (c) 10 m s−1   (d) 5 m s−1

Solution. vCM = (m1v1 + m2v2)/(m1 + m2) = ((10 kg)(14 m s−1) + (4 kg)(0))/(10 kg + 4 kg) = 10 m s−1. Answer: (c) 10 m s−1.

Teacher's Note: Centre-of-mass velocity is total momentum over total mass; the lighter block starts at rest.

Exam Note: Only the heavier block has initial velocity.

Question 1.1.32. A thin uniform rod, pivoted at O, is rotating in the horizontal plane with a constant angular speed ω, as shown in the figure. At t = 0, a small insect starts from O and moves with a constant speed v relative to the rod towards the other end. It reaches the end of the rod at t = T and stops. The magnitude of the torque (|τ|) on the system about O as a function of time (t) is best represented by
(Figure: four |τ|–t graphs up to t = T. (a) straight line from the origin to T then constant; (b) straight line from the origin ending at T (dashed vertical at T); (c) curve rising then constant; (d) curve rising steeply ending at T.)

Solution. Angular momentum L = Iω = m(vt)2ω = mv2ωt2. Hence torque τ = dL/dt = 2mv2ωt. So τ ∝ t, which represents a straight line passing through the origin. Answer: (b).

Teacher's Note: Insect at distance vt gives L ∝ t2, so torque ∝ t.

Exam Note: Differentiate L = mv2ωt2.

Question 1.1.33. A small mass m is attached to a massless string whose other end is fixed at P, as shown in the figure. The mass is undergoing a circular motion in the xy-plane with the centre at O and a constant angular speed ω. If the angular momentum of the system calculated about O and P are respectively denoted by LO and LP then
(Figure: P lies on the z-axis above O; the mass moves in a horizontal circle about O, joined to P by the string.)
(a) LO and LP do not vary with time
(b) LO varies with time, while LP remains constant
(c) LO remains constant, while LP varies with time
(d) LO and LP both vary with time

Solution. LO has a constant magnitude and a constant direction (perpendicular to the plane of rotation); LP has a constant magnitude, but its direction continuously changes with time. Answer: (c).

Teacher's Note: About O, r and v are always perpendicular in one plane; about P the vector tilts and rotates.

Exam Note: Angular momentum is a vector: direction counts.

Question 1.1.34. Consider a disc rotating in the horizontal plane with a constant angular velocity ω about its centre O. The disc has a shaded region on one side of the diameter and an unshaded region on the other side, as shown in the figure. When the disc is in the orientation as shown, two pebbles P and Q are simultaneously projected at an angle towards R. The velocity of projection is in the yz-plane and is the same for both the pebbles with respect to this disc. Assume that (i) they land back on the disc before the disc has completed 1/8 rotation, (ii) their range is less than half the disc radius and (iii) ω remains constant throughout. Then,
(Figure: a disc with the left half shaded; along a vertical diameter lie R at the top, then Q just above O, O at the centre and P near the bottom; the disc rotates with angular velocity ω.)
(a) P lands in the shaded region and Q, in the unshaded region
(b) P lands in the unshaded region and Q, in the shaded region
(c) both P and Q land in the unshaded region
(d) both P and Q land in the shaded region

Solution. At t = T/8 = (1/8)(2π/ω) = π/4ω, the x-coordinate of P is (ωR)(π/4ω) = πR/4 > R cos 45°. Therefore both P and Q land in the unshaded region. Answer: (c).

Teacher's Note: Pebbles keep the disc’s tangential speed; compare the sideways shift with the rotated boundary.

Exam Note: Both pebbles shift sideways by the same logic.

Question 1.1.35. One end of a thick horizontal copper wire of length 2L and radius 2R is welded to an end of another thin horizontal copper wire of length L and radius R. When the arrangement is stretched by applying forces at two ends, the ratio of the elongation in the thin wire to that in the thick wire is
(a) 0.25   (b) 0.50   (c) 2.00   (d) 4.00

Solution. If x1 and x2 are the elongations in the thick and thin wires respectively, the Young modulus Y = (F/A1)/(x1/L1) = (F/A2)/(x2/L2). Therefore x2/x1 = (A1/A2)(L2/L1) = 4 × (1/2) = 2. Answer: (c) 2.00.

Teacher's Note: Same force and same Y: elongation ∝ L/A; area ratio is 4, length ratio 1/2.

Exam Note: Area ratio uses radius squared.

Question 1.1.36. Consider three regular polygons with the number of sides n = 3, 4 and 5 as shown in the figures. The centre of mass of all the polygons is at the height h from the ground. They roll on a horizontal surface about the leading vertex without slipping and sliding as depicted. The maximum increase in the height of the locus of the centre of mass for each polygon is Δ. Then Δ depends on n and h as
(a) Δ = h sin(2π/n)   (b) Δ = h sin2(π/n)   (c) Δ = h tan2(π/2n)   (d) Δ = h[1/cos(π/n) − 1]

Solution. The centre of mass is at height h; when the polygon pivots about the leading vertex, the distance of the CM from that vertex is R = h/cos(π/n) at the highest position, since cos(π/n) = h/R. Hence Δ = R − h = h[1/cos(π/n) − 1]. Answer: (d).

Teacher's Note: Highest CM position equals its distance R from the vertex, with cos(π/n) = h/R.

Exam Note: Δ is R − h.

Question 1.1.37. A geostationary satellite orbits around the earth in a circular orbit of radius 36000 km. Then, the time period of a spy satellite orbitting a few hundred kilometres above the earth’s surface (Re = 6400 km) will approximately be
(a) ½ h   (b) 1 h   (c) 2 h   (d) 4 h

Solution. For a satellite in a circular orbit around the earth, the time period T depends on the radius r as T2 ∝ r3. Here, for the geostationary satellite, T1 = 24 h and r1 = 36000 km. For the spy satellite, r2 = 6400 km and if the time period be T2, T22/T12 = r23/r13 or T2 = T1(r2/r1)3/2 = (24 h)(6400/36000)3/2 ≈ 2 h. Answer: (c) 2 h.

Teacher's Note: Kepler’s third law with radius taken as about the earth’s radius.

Exam Note: Use r ≈ 6400 km for a low orbit.

Question 1.1.38. A thin uniform annular disc (see figure) of mass M has the outer radius 4R and the inner radius 3R. The work required to take a unit mass from the point P on its axis to infinity is
(Figure: annular disc with inner radius 3R and outer radius 4R; the point P is on the axis at a height 4R above the centre.)
(a) (2GM/7R)(4√2 − 5)   (b) −(2GM/7R)(4√2 − 5)   (c) GM/4R   (d) (2GM/5R)(√2 − 1)

Solution. Mass per unit area σ = M/(π(4R)2 − π(3R)2) = M/(7πR2), area of a ring = 2πx dx, and mass of a ring dm = 2πσx dx. Potential at P: VP = −G∫3R4R dm/[(4R)2 + x2]1/2 = −(2GM/7R2)[√(16R2 + x2)]3R4R = −(2GM/7R)(4√2 − 5). Work required to take unit mass to infinity = −VP = (2GM/7R)(4√2 − 5). Answer: (a).

Teacher's Note: Work to infinity equals minus the potential; integrate ring contributions on the axis.

Exam Note: Positive work: potential is negative.

Question 1.1.39. A satellite is moving with a constant speed v in a circular orbit around the earth. An object of mass m is ejected from the satellite such that it just escapes from the gravitational pull of the earth. At the time of its ejection, the kinetic energy of this object is
(a) ½mv2   (b) mv2   (c) (3/2)mv2   (d) 2mv2

Solution. For the object to escape, KE + (−GMm/r) = 0. For circular motion, mv2/r = GMm/r2. So GMm/r = mv2 = required KE. Answer: (b) mv2.

Teacher's Note: Just escaping means total energy zero, so KE = GMm/r = mv2 from orbit condition.

Exam Note: Use orbital condition to replace GM/r.

Question 1.1.40. A planet of radius R = (1/10)(radius of the earth) has the same mass density as the earth. Scientists dig a well of depth R/5 on it and lower a wire of the same length and of linear mass density 10−3 kg m−1 into it. If the wire is not touching anywhere, the force applied at the top of the wire by a person holding it in place is (taking the radius of the earth as 6 × 106 m and the acceleration due to gravity of the earth as 10 m s−2)
(a) 96 N   (b) 108 N   (c) 120 N   (d) 150 N

Solution. The value of g at a distance r (where r < R) from the centre of a planet is g = g0(r/R) = (4/3)πGρr. The force required to keep the wire at rest is F = weight of the wire = ∫dm·g = ∫4R/5R (λ dr)((4/3)πGρr) = (4/3)πGρλ [r2/2]4R/5R = (4/3)πGρλ(9R2/50). Taking ρ = Me/((4/3)πRe3) and R = Re/10, we obtain F = (9/5000)gReλ = 108 N. Answer: (b) 108 N.

Teacher's Note: Inside a uniform planet g grows linearly with r; integrate the wire’s weight.

Exam Note: Wire lies from r = 4R/5 to R.

Question 1.1.41. A rocket is launched normal to the surface of the earth, away from the sun, along the line joining the sun and the earth. The sun is 3 × 105 times heavier than the earth and is at a distance 2.5 × 104 times larger than the radius of the earth. The escape velocity from the earth’s gravitational field is ve = 11.2 km s−1. The minimum initial velocity required for the rocket to be able to leave the sun–earth system is close to
(a) 60 km s−1   (b) 40 km s−1   (c) 70 km s−1   (d) 20 km s−1

Solution. The escape speed from the earth is ve = √(2gRe) = √(2GMe/R) = 11.2 km s−1. If v0 is the escape speed from the earth–sun system then ½mv02 − GMme/R − GMSm/((2.5 × 104)R) ≥ 0. For the rocket to just escape, v02/2 = GMe/R + G × 3 × 105 Me/((2.5 × 104)R) = 13GMe/R, so v0 = √13 ve = √13 × 11.2 km s−1 = 40.4 km s−1 ≈ 40 km s−1. Answer: (b).

Teacher's Note: Add earth and sun potentials; the sun term equals 12 times the earth term.

Exam Note: Express everything in GMe/R.

Question 1.1.42. A ring of mass M and radius R is rotating with the angular speed ω about a fixed vertical axis passing through its centre O with two point masses each of mass M/8 at rest at O. These masses can move radially outwards along the two massless rods fixed on the ring as shown in the figure. At some instant the angular speed of the system is 8ω/9 and one of the masses is at a distance of 3R/5 from O. At this instant, the distance of the other point mass from O is
(a) 2R/3   (b) 3R/5   (c) R/3   (d) 4R/5

Solution. Conserving the angular momentum of the system, MR2ω = MR2·(8ω/9) + (M/8)(3R/5)2(8ω/9) + (M/8)x2(8ω/9) ⇒ x = 4R/5. Answer: (d) 4R/5.

Teacher's Note: Angular momentum is conserved: ring plus two sliding masses at different radii.

Exam Note: Write all three terms with ω′ = 8ω/9.

Question 1.1.43. A wooden block performs SHM on a frictionless surface with a frequency of ν0. The block carries a charge +Q on its surface. If a uniform electric field E is switched on as shown then the SHM of the block will be of
(Figure: block carrying +Q attached to a spring fixed to a wall on the right; the field E points to the right.)
(a) the same frequency and with a shifted mean position
(b) the same frequency and with the same mean position
(c) a changed frequency and with a shifted mean position
(d) a changed frequency and with the same mean position

Solution. The frequency f = (1/2π)√(K/m) of a spring–block system is independent of the external fields (e.g., gravity). A constant electric force QE only shifts the equilibrium (mean) position. Answer: (a).

Teacher's Note: A constant extra force shifts equilibrium but does not change k or m, so frequency stays.

Exam Note: Frequency depends on k and m only.

Question 1.1.44. A small block is connected to one end of a massless spring of unstretched length 4.9 m. The other end of the spring (see the figure) is fixed. The system lies on a horizontal frictionless surface. The block is stretched by 0.2 m and then released. It then executes SHM with an angular frequency of ω = (π/3) rad s−1. Simultaneously at t = 0, a small pebble is projected with a speed v from the point P at an angle of 45° as shown in the figure. The point P is at a horizontal distance of 10 m from O. If the pebble hits the block at t = 1 s, the value of v is
(a) √50 m s−1   (b) √51 m s−1   (c) √52 m s−1   (d) √53 m s−1

Solution. Time of flight T = 2u sin θ/g, i.e. 1 s = 2u·sin 45°/10. Therefore u = 5√2 m s−1 = √50 m s−1. (Check: the pebble’s range = u2 sin 90°/g = 5 m, so it lands 5 m from P, at x = 5 m from O; the block is at 4.9 + 0.2 cos(π/3) = 5.0 m at t = 1 s, so they meet.) Answer: (a).

Teacher's Note: Time of flight fixes the speed; the block’s position at t = 1 s confirms the meeting point.

Exam Note: Use T = 2u sin θ/g with T = 1 s.

Question 1.1.45. A hemispherical portion of radius R is removed from the bottom of a cylinder of radius R. The volume of the remaining cylinder is V and its mass is M. It is suspended by a string in a liquid of density ρ. It stays vertical inside the liquid. The upper surface of the cylinder is at a depth h below the liquid surface. The force on the bottom of the cylinder by the liquid is
(a) Mg   (b) Mg − Vρg   (c) Mg + πR2hρg   (d) ρg(V + πR2h)

Solution. The net upward buoyancy force on the cylinder = weight of the liquid displaced by it = ρgV = (upward force on the bottom) − (downward force on the top). The downward force on the top is hρg·πR2. Therefore the force on the bottom is ρgV + (hρg)πR2 = ρg(V + πR2h). Answer: (d).

Teacher's Note: Bottom force = buoyancy + top force, since net upthrust is ρgV.

Exam Note: Top force is pressure hρg times area πR2.

Question 1.1.46. A wooden block, with a coin placed on its top, floats in water, as shown in the figure. The distance l and h are shown. After some time the coin falls into the water. Then,
(Figure: block floating with the coin on top; l is the height of the block above the water surface and h is the depth of water in the vessel.)
(a) l decreases and h increases   (b) l increases and h decreases   (c) both l and h increase   (d) both l and h decrease

Solution. When the coin slips into the water, the wooden block moves up and l increases. When the coin was floating (on the block), it displaced water equal to its own weight. When inside the water, it displaces water equal to its own volume. As its density is greater than that of water, it displaced more water in the first case. Hence, h decreases when it falls into the water. Answer: (b). (Corrected: the printed hint says “l decreases”, which contradicts its own answer (b); the block rises, so l increases.)

Teacher's Note: Coin on block displaces water by its weight; submerged it displaces only its volume, less.

Exam Note: Compare displaced volumes before and after.

Question 1.1.47. A thin uniform cylindrical shell, closed at both ends, is partially filled with water. It is floating vertically in water in the half-submerged state. If ρc is the relative density of the material of the shell with respect to water then the correct statement is that the shell is
(a) more than half-filled if ρc is less than 0.5
(b) more than half-filled if ρc is more than 1
(c) half-filled if ρc is more than 0.5
(d) less than half-filled if ρc is less than 0.5

Solution. Let m be the mass of the shell, V0 its volume and Vi the volume of water inside. Floating half-submerged: mg + (Viρ)g = (V0/2) × ρ × g, so Vi = V0/2 − m/ρ. Hence Vi < V0/2: the shell is less than half-filled. Answer: (d).

Teacher's Note: Weight of shell plus inside water equals half-volume buoyancy, so water is below half.

Exam Note: Write the floating balance first.

Question 1.1.48. A glass capillary tube is of the shape of a truncated cone with an apex angle α so that its two ends have cross sections of different radii. When dipped in water vertically, water rises in it to a height h, where the radius of its cross section is b. If the surface tension of water is s, its density is ρ and its contact angle with glass is θ, the value of h will be
(a) (2s/bρg) cos(θ − α)   (b) (2s/bρg) cos(θ + α)   (c) (2s/bρg) cos(θ − α/2)   (d) (2s/bρg) cos(θ + α/2)

Solution. From the geometry of the figure, b/R = cos(θ + α/2), where R is the radius of the meniscus. If p0 = atmospheric pressure then p0 − 2s/R + hρg = p0 ⇒ 2s/R = hρg ⇒ h = 2s/(Rρg) = (2s/bρg) cos(θ + α/2). Answer: (d).

Teacher's Note: Meniscus radius R = b/cos(θ + α/2); excess pressure 2s/R balances hρg.

Exam Note: Wall is tilted by α/2, so angle is θ + α/2.

Question 1.1.49. Two blocks A and B of masses 2m and m respectively are connected by a massless and inextensible string. The whole system is suspended by a massless spring, as shown in the figure. The magnitude of acceleration of A and B immediately after the string is cut are respectively
(Figure: spring hung from a ceiling, block A (2m) attached below it, block B (m) hanging from A by the string.)
(a) g and g/2   (b) g/2 and g   (c) g and g   (d) g/2 and g/2

Solution. From the free-body diagram of block A, T2 = T1 + 2mg. Similarly, for block B, T1 = mg and T2 = 3mg. When the string is cut, T1 = 0. For B, mg = maB ⇒ aB = g. For A, 3mg − 2mg = 2maA ⇒ aA = g/2. Answer: (b).

Teacher's Note: Spring force cannot change instantly; only the string tension disappears.

Exam Note: Spring force stays 3mg at the instant of cutting.

Question 1.1.50. A system of binary stars of masses mA and mB are moving in circular orbits of radii rA and rB respectively. If TA and TB are the time periods of the stars A and B respectively,
(a) TA/TB = (rA/rB)3/2   (b) TA > TB if rA > rB   (c) TA > TB if mA > mB   (d) TA = TB

Solution. The gravitational attraction provides the required centripetal force. Thus, Gm1m2/(r1 + r2)2 = mAωA2r1 = mBωB2r2. Further, the system rotates about the centre of mass O, so mAr1 = mBr2 ⇒ ωA = ωB ∴ TA = TB. Answer: (d).

Teacher's Note: Both stars stay on a line through the centre of mass, so they share one angular speed.

Exam Note: Kepler’s T2 ∝ r3 does not apply here.

Question 1.1.51. A solid sphere of mass M, radius R and having moment of inertia as I is recast into a disc of thickness t, whose moment of inertia about an axis passing through its edge and perpendicular to its plane remains I. Then the radius of the disc will be
(a) 2R/√15   (b) R√(2/15)   (c) 4R/√15   (d) R/4

Solution. Since the mass of the sphere is unchanged, ((2/5)MR2)sphere = ((1/2)MR02 + MR02)disc or (2/5)R2 = (3/2)R02. Therefore the radius of the disc is R0 = 2R/√15. Answer: (a).

Teacher's Note: Parallel-axis theorem: disc about its edge is (3/2)MR02.

Exam Note: Use the edge, not the centre, of the disc.

Question 1.1.52. Two particles each of mass m are tied at the ends of a light string of length 2a. The whole system is kept on a smooth horizontal surface with the string held tight so that each particle remains at a distance a from the centre P (as shown in the figure). Now the midpoint of the string is pulled vertically upwards with a small but constant force F. As a result, the particles move towards each other on the surface. The magnitude of the acceleration when the separation between them becomes 2x is
(a) (F/2m)·a/√(a2 − x2)   (b) (F/2m)·x/√(a2 − x2)   (c) (F/2m)·x/a   (d) (F/2m)·√(a2 − x2)/x

Solution. Let each half of the string make angle θ with the horizontal and T be the tension. Then 2T sin θ = F and T cos θ = max. Therefore 2 tan θ = F/(max) ⇒ ax = F/(2m tan θ) = (F/2m)(x/√(a2 − x2)). Answer: (b).

Teacher's Note: Vertical balance at the midpoint gives T sin θ; horizontal part accelerates each particle.

Exam Note: tan θ = √(a2 − x2)/x from geometry.

Question 1.1.53. A small object of uniform density rolls up a curved surface with an initial velocity v. It reaches up to a maximum height of 3v2/4g with respect to the initial position. The object is a
(a) ring   (b) solid sphere   (c) hollow sphere   (d) disc

Solution. By conservation of mechanical energy, ½mv2(1 + K2/R2) = mgh = mg(3v2/4g) ⇒ 1 + K2/R2 = 3/2. Therefore K2/R2 = 1/2, which is true for a disc. Answer: (d).

Teacher's Note: Rolling kinetic energy has factor (1 + K2/R2); match 1/2 to the disc.

Exam Note: Disc: K2 = R2/2.

Question 1.1.54. A spherically symmetric gravitational system of particles has a mass density ρ = ρ0 for r < R and 0 for r > R, where ρ0 is a constant. A test mass can undergo a circular motion under the influence of the gravitational field of particles. Its speed v as a function of the distance r (where 0 < r < ∞) from the centre of the system is represented by
(Figure: four v–r graphs with R marked. (a) straight line rising to R, then constant; (b) a decaying curve from infinity; (c) straight line rising to R, then falling as a decaying curve; (d) constant up to R, then decaying.)

Solution. The gravitational system represents a solid sphere of radius R having a uniform density ρ = ρ0. For r < R, force: G(4/3)πr3ρm/r2 = mv2/r ∴ v ∝ r (a straight line from r = 0 to r = R). For r > R, G(4/3)πR3ρm/r2 = mv2/r, i.e. v ∝ 1/√r. Therefore the correct plot is the option (c). Answer: (c).

Teacher's Note: Inside, enclosed mass ∝ r3 gives v ∝ r; outside, v ∝ 1/√r.

Exam Note: Graph must be continuous at r = R.

Question 1.1.55. A bob of mass m is suspended by a massless string of length L. The horizontal velocity v at the position A is just sufficient to make it reach the point B. The angle θ at which the speed of the bob is the half of that at A satisfies
(Figure: vertical circle of radius L with A at the bottom, B at the top and C a point on the circle at angle θ from the downward vertical.)
(a) θ = π/4   (b) π/4 < θ < π/2   (c) π/2 < θ < 3π/4   (d) 3π/4 < θ < π

Solution. The critical speed at A is √(5gL). Conserving energy from A to C, ½m(√(5gL))2 = ½mvC2 + mgL(1 − cos θ), with vC = vA/2 = ½√(5gL). This gives cos θ = −7/8 = −0.87. Since cos(3π/4) = −1/√2 = −0.71, we get 3π/4 < θ < π. Answer: (d).

Teacher's Note: Speed at A is √(5gL) for a complete circle; apply energy conservation to v/2.

Exam Note: Compare cos θ = −7/8 with cos 135°.

Question 1.1.56. A glass tube of uniform internal radius (r) has a valve separating the two identical ends. Initially, the valve is in a tightly closed position. The end 1 has a hemispherical soap bubble of radius r. The end 2 has a subhemispherical soap bubble, as shown in the figure. Just after opening the valve,
(Figure: U-shaped tube with a valve at the top; bubble at end 1 is a hemisphere, bubble at end 2 is smaller than a hemisphere.)
(a) air from the end 1 flows towards the end 2: no change occurs in the volume of the soap bubbles
(b) air from the end 1 flows towards the end 2: the volume of the soap bubble at the end 1 decreases
(c) no change occurs
(d) air from the end 2 flows towards the end 1: the volume of the soap bubble at the end 1 increases

Solution. The pressure inside a spherical soap bubble exceeds the outer (atmospheric) pressure p0 by 4S/R, where S is the surface tension of the soap solution, and R is the radius. Thus, the pressure inside the bubble is p = p0 + 4S/R. Since R2 > R1, p2 < p1. Hence, air flows from 1 to 2, and the bubble at end 1 shrinks. Answer: (b).

Teacher's Note: Smaller radius means higher pressure, so air flows from the hemispherical bubble to the flatter one.

Exam Note: A subhemisphere has a larger radius than r.

Question 1.1.57. A block B is attached to two unstretched springs S1 and S2 with spring constants k and 4k respectively (see the figure I). The other ends are attached to the identical supports M1 and M2 which are not fixed to the walls. The springs and supports have negligible masses. There is no friction anywhere. The block B is displaced towards the wall 1 by a small distance x (see the figure II) and then released. The block returns and moves a maximum distance y towards the wall 2. The displacements x and y are measured with respect to the equilibrium position of the block B. The ratio y/x is
(a) 4   (b) 2   (c) 1/2   (d) 1/4

Solution. By the law of conservation of mechanical energy, ½kx2 = ½(4k)y2 ⇒ y/x = 1/2. Answer: (c) 1/2.

Teacher's Note: Only the spring on the compressed side acts on each side, since supports are free.

Exam Note: Equate ½kx2 to ½(4k)y2.

Question 1.1.58. The x–t graph of a particle undergoing a simple harmonic motion is shown here. The acceleration of the particle at t = 4/3 s is
(Figure: sinusoidal x–t graph in cm with amplitude 1 cm and period 8 s, starting from x = 0 at t = 0.)
(a) (√3π2/32) cm s−2   (b) −π2/32 cm s−2   (c) π2/32 cm s−2   (d) −(√3π2/32) cm s−2

Solution. From the given x–t graph of SHM, displacement = x = A sin ωt, so v = Aω cos ωt and a = −Aω2 sin ωt. Given A = 1 cm, ω = 2π/8 rad s−1 and t = 4/3 s, a = −(1 cm)(2π/8 s−1)2 sin((2π/8)(4/3)) = −(√3π2/32) cm s−2. Answer: (d).

Teacher's Note: Read A and period from the graph, then a = −ω2x with x = A sin ωt.

Exam Note: Phase is π/3, so sin = √3/2.

Question 1.1.59. A block of base 10 cm × 10 cm and height 15 cm is kept on an inclined plane. The coefficient of friction between them is √3. The inclination θ of this inclined plane from the horizontal plane is gradually increased from 0°. Then,
(a) the block will start sliding down the plane at θ = 30°
(b) the block will remain at rest on the plane up to a certain θ and then it will topple
(c) the block will start sliding down the plane at θ = 60° and continue to do so at higher angles
(d) the block will start sliding down the plane at θ = 60° and, on further increasing θ, it will topple at a certain θ

Solution. The block slides down the plane when mg sin θ ≥ f = μN = μmg cos θ, or tan θ ≥ μ = √3 = 1.732. The block topples without sliding when f(15/2) ≥ N(5) (taking torque about the CM), or μN(15/2) ≥ N(5), or μ ≥ 2/3 = 0.67, i.e. tan θ ≥ 0.67. Thus, the block will neither slip nor topple till θ ≤ tan−1(0.67), and when θ exceeds this, it topples before sliding occurs. Answer: (b).

Teacher's Note: Compare the toppling angle tan θ = 2/3 with the sliding angle tan θ = √3.

Exam Note: Toppling comes first, at tan θ = 0.67.

Question 1.1.60. Two small particles of equal masses start moving in opposite directions from a point A in a horizontal circular orbit. Their tangential velocities are v and 2v respectively, as shown in the figure. Between collisions, the particles move with constant speeds. After making how many elastic collisions, other than that at A, will these two particles again reach the point A?
(a) Four   (b) Three   (c) Two   (d) One

Solution. The angular displacement of the faster particle is 2θ and that of the slower particle is θ. So 2θ + θ = 2π ⇒ θ = 2π/3. Hence, the first collision will occur at B, where the velocities are interchanged due to equal masses and their elastic collision. The second collision will occur at C and the third at A. Thus, two collisions will occur before meeting at A. Answer: (c).

Teacher's Note: Equal masses exchange velocities; collision points are 120° apart.

Exam Note: Count collisions before the third at A.

Question 1.1.61. A block M shown in the figure oscillates in a simple harmonic motion with amplitude A. The amplitude of the point P is
(Figure: block M on the right attached to spring k2, which is joined at point P to spring k1 fixed to the wall on the left.)
(a) k1A/k2   (b) k2A/k1   (c) k1A/(k1 + k2)   (d) k2A/(k1 + k2)

Solution. The springs are in series; so the restoring force is the same in both the springs. Hence k1x1 = k2x2. Given that x1 + x2 = A, ∴ x1 = Ak2/(k1 + k2). Answer: (d).

Teacher's Note: Series springs carry equal force, so extensions are inversely proportional to constants.

Exam Note: P’s amplitude is the extension of spring k1.

Question 1.1.62. A piece of wire is bent in the shape of the parabola y = kx2 (the y-axis being vertical), with a bead of mass m on it. The bead can slide on the wire without friction. It stays at the lowest point of the parabola when the wire is at rest. The wire is now accelerated parallel to the x-axis with a constant acceleration a. The distance of the new equilibrium position of the bead, where the bead can stay at rest with respect to the wire, from the y-axis is
(a) a/gk   (b) a/2gk   (c) 2a/gk   (d) a/4gk

Solution. Forces acting on the bead in the wire’s frame are (i) weight (mg), (ii) normal reaction (N) and (iii) pseudo force (ma). Resolving N, for balance N sin θ = ma and N cos θ = mg. Therefore tan θ = a/g ⇒ dy/dx = a/g. But y = kx2, so dy/dx = 2kx ⇒ x = a/2gk. Answer: (b).

Teacher's Note: In the wire’s frame, the net of mg and ma must be normal to the wire: slope = a/g.

Exam Note: Slope of the parabola is 2kx.

Question 1.1.63. A uniform rod of length L and mass M is pivoted at the centre. Its two ends are attached to two springs of equal spring constants (k). The springs are fixed to rigid supports, as shown in the figure, and the rod is free to oscillate in the horizontal plane. The rod is gently pushed through a small angle θ in one direction and then released. The frequency of the oscillation is
(Figure: rod pivoted at its centre; the upper end is joined to a spring fixed to the left wall, the lower end to a spring fixed to the right wall.)
(a) (1/2π)√(2k/M)   (b) (1/2π)√(k/M)   (c) (1/2π)√(6k/M)   (d) (1/2π)√(24k/M)

Solution. When the rod is turned through an angle θ, the restoring torque (opposing θ) is τ = −2k(Lθ/2)(L/2) = I d2θ/dt2, with I = ML2/12. Therefore d2θ/dt2 = −(kL2/2)θ/(ML2/12) = −(6k/M)θ. This represents an angular SHM for which ω = √(6k/M) = 2π/T or f = (1/2π)√(6k/M). Answer: (c).

Teacher's Note: Two springs give torque kL2θ/2; divide by I = ML2/12.

Exam Note: Use I = ML2/12 about the centre.

1.2 Heat and Thermodynamics

Question 1.2.1. When a block of iron floats in mercury at 0 °C, a fraction k1 of its volume is submerged; while at the temperature 60 °C, a fraction k2 is seen to be submerged. If the coefficient of volume expansion for iron is γFe and that for mercury is γHg, the ratio k1/k2 can be expressed as
(a) [1 + (60 °C)γFe]/[1 + (60 °C)γHg]   (b) [1 − (60 °C)γFe]/[1 + (60 °C)γHg]   (c) [1 + (60 °C)γFe]/[1 − (60 °C)γHg]   (d) [1 + (60 °C)γHg]/[1 + (60 °C)γFe]

Solution. Let ρFe and ρHg denote respectively the densities of iron and mercury at 0 °C and m be the mass of the block. The volume of the block is m/ρFe and that of the displaced mercury is k1m/ρFe. Therefore (k1m/ρFe)ρHg = m or k1 = ρFe/ρHg. Also, ρt = ρ0/(1 + γt). So k2 = [ρFe/(1 + γFe × 60 °C)] × [(1 + γHg × 60 °C)/ρHg] = k1(1 + (60 °C)γHg)/(1 + (60 °C)γFe), or k1/k2 = (1 + (60 °C)γFe)/(1 + (60 °C)γHg). Answer: (a).

Teacher's Note: Floating fraction equals density ratio; both densities fall with temperature as 1/(1 + γt).

Exam Note: Write each density at 60 °C.

Question 1.2.2. Starting with the same initial conditions, an ideal gas expands from the volume V1 to V2 in three different ways. The work done by the gas is W1 if the process is purely isothermal, W2 if purely isobaric, and W3 if purely adiabatic. Then,
(a) W2 > W1 > W3   (b) W2 > W3 > W1   (c) W1 > W2 > W3   (d) W1 > W3 > W2

Solution. The three processes are plotted on a p–V diagram. AB is isobaric, AC is isothermal, and AD is adiabatic. In each case, the work done is equal to the area under the curve. The isobaric line AB lies highest, then the isothermal curve AC, then the adiabatic curve AD, so W2 > W1 > W3. Answer: (a).

Teacher's Note: Work is the area under the curve on a p–V diagram; adiabat falls fastest.

Exam Note: Sketch the three curves from one point.

Question 1.2.3. An ideal gas is taken through the cycle A → B → C → A, as shown in the figure. If the net heat supplied to the gas in the cycle is 5 J, the work done by the gas in the process C → A is
(Figure: p–V diagram with V (m3) on the vertical axis and p (N m−2) on the horizontal axis; A at p = 10, V = 1; B at p = 10, V = 2; C at V = 2 with smaller p; AB vertical, BC horizontal, CA a straight line.)
(a) −5 J   (b) −10 J   (c) −15 J   (d) −20 J

Solution. From the first law of thermodynamics, Q = ΔU + W. For a cyclic process, ΔU = 0. Also, Q = 5 J. W = WAB + WBC + WCA. WAB = pΔV = (10 N m−2)(1 m3) = 10 J and WBC = 0. ∴ 5 J = 10 J + WCA or WCA = −5 J. Answer: (a) −5 J.

Teacher's Note: In a cycle ΔU = 0, so net heat equals net work; BC at constant volume does none.

Exam Note: Work along an isobar is pΔV.

Question 1.2.4. 5.6 L of helium gas at STP is adiabatically compressed to 0.7 L. Taking the initial temperature to be T1, the work done in the process is
(a) (9/8)RT1   (b) (3/2)RT1   (c) (15/8)RT1   (d) (9/2)RT1

Solution. TVγ−1 = constant and γ for helium (a monatomic gas) is 5/3. ∴ T1(5.6)2/3 = T2(0.7)2/3, hence T2 = 4T1. ∴ W = [nR/(γ − 1)](T2 − T1) = (1/4)(R/(2/3))(4T1 − T1) = (9/8)RT1. Answer: (a).

Teacher's Note: n = 5.6/22.4 = 1/4 mol; adiabatic law gives T2 = 4T1.

Exam Note: Magnitude of work done on the gas.

Question 1.2.5. A mixture of 2 mol of helium gas (atomic mass = 4 amu) and 1 mol of argon gas (atomic mass = 40 amu) is kept at 300 K in a container. The ratio of the rms speeds (vrms(He)/vrms(Ar)) is
(a) 0.32   (b) 0.45   (c) 2.24   (d) 3.16

Solution. vrms(He)/vrms(Ar) = √(3RT/mHe)/√(3RT/mAr) = √(mAr/mHe) = √(40/4) = √10 = 3.16. Answer: (d) 3.16.

Teacher's Note: At the same temperature rms speed varies inversely as the square root of molar mass.

Exam Note: Mole numbers are irrelevant here.

Question 1.2.6. Two moles of ideal helium gas are in a rubber balloon at 30 °C. The balloon is fully expandable and can be assumed to require no energy for its expansion. The temperature of the gas in the balloon is slowly changed to 35 °C. The amount of heat required in raising the temperature is nearly (take R = 8.31 J mol−1 K−1)
(a) 62 J   (b) 104 J   (c) 124 J   (d) 208 J

Solution. ΔQ = nCpΔT = n(γ/(γ − 1))R ΔT = 2((5/2)R)ΔT = 2(5/2 × 8.31) × 5 ≈ 208 J. Answer: (d) 208 J.

Teacher's Note: Balloon expands at constant pressure, so heat uses Cp = (5/2)R for helium.

Exam Note: Use Cp, not Cv.

Question 1.2.7. A real gas behaves like an ideal gas if its
(a) pressure and temperature are both high   (b) pressure and temperature are both low   (c) pressure is high and temperature is low   (d) pressure is low and temperature is high

Solution. At low pressures, the number of molecules per unit volume decreases, so that the ‘point mass’ approximation holds. Also, at high temperatures, the average speeds increase. Answer: (d).

Teacher's Note: Low pressure makes molecules far apart; high temperature makes attractions negligible.

Exam Note: Low p and high T together.

Question 1.2.8. One mole of an ideal gas in the initial state A undergoes a cyclic process ABCA, as shown in the figure. Its pressure at A is p0. Choose the correct statement from the following.
(Figure: V–T diagram; A at (T0, V0), B at (T0, 4V0) vertically above A; C at V0 to the left of A, joined to B by a straight line and to A by a horizontal line; arrows A → B → C → A.)
(a) The internal energies at A and B are different.
(b) The work done by the gas in process AB is p0V0 ln 4.
(c) The pressure at C is p0/4.
(d) The temperature at C is T0/4.

Solution. (Internal energy) ∝ (absolute temperature). ∴ UA = UB. In the isothermal process AB, W = nRT ln(Vf/Vi) = p0V0 ln(VB/VA) = p0V0 ln 4. Answer (from key): (b).

Teacher's Note: AB is isothermal, so U is unchanged and W = nRT ln(VB/VA).

Exam Note: Use the isothermal work formula with volume ratio 4.

Question 1.2.9. An ideal gas is initially at a thermodynamic temperature T and has a volume V. Its volume is increased by ΔV due to an increase in temperature ΔT, the pressure remaining constant. Which of the following graphs shows how the quantity δ = ΔV/(VΔT) varies with temperature?
(Figure: four δ–temperature graphs between T and T + ΔT: (a) horizontal line; (b) rising straight line; (c) falling curve (hyperbola type); (d) rising curve.)

Solution. pV = nRT. At constant pressure, pΔV = nR(ΔT). Dividing, ΔV/V = ΔT/T or δ = ΔV/(VΔT) = 1/T, i.e. δ ∝ 1/T. Answer: (c).

Teacher's Note: At constant pressure ΔV/V = ΔT/T, so δ = 1/T falls hyperbolically.

Exam Note: Divide pΔV = nRΔT by pV = nRT.

Question 1.2.10. Three rods made of the same material and having the same cross section have been joined as shown in the figure. Each rod is of the same length. The left and right ends are kept at 0 °C and 90 °C respectively. The temperature of the junction of the three rods will be
(Figure: one rod at 0 °C on the left meets two rods, each ending at 90 °C, at the junction.)
(a) 45 °C   (b) 60 °C   (c) 30 °C   (d) 20 °C

Solution. As the three rods are made of the same material and have the same dimensions, they have the same thermal resistance, say R. Let θ be the temperature of the junction. The two 90 °C rods are in parallel (resistance R/2). Therefore i = (90 °C − θ)/(R/2) = (θ − 0 °C)/R or 180 °C − 2θ = θ or θ = 60 °C. Answer: (b) 60 °C.

Teacher's Note: Two parallel rods have resistance R/2; equal heat current through both sections.

Exam Note: Treat it as thermal resistances in series.

Question 1.2.11. An ideal black body at the room temperature is thrown into a furnace. It is observed that
(a) initially it is the darkest body and at later times the brightest
(b) it is the darkest body at all times
(c) it cannot be distinguished at all times
(d) initially it is the darkest body and at later times it cannot be distinguished

Solution. A furnace behaves as a black body. Answer: (d). (Initially the body at room temperature is cooler and absorbs all radiation, so it looks darkest; once in thermal equilibrium it emits as the furnace does and cannot be distinguished.)

Teacher's Note: A black body in equilibrium with a black-body cavity radiates identically to its surroundings.

Exam Note: Initially cooler, finally indistinguishable.

Question 1.2.12. Three very large plates of same area are kept parallel and close to each other. They are considered ideal black surfaces and have very high thermal conductivity. The first and the third plates are maintained at the temperatures 2T and 3T respectively. The temperature of the middle (i.e., the second) plate under the steady-state condition is
(a) (65/2)1/4 T   (b) (97/4)1/4 T   (c) (97/2)1/4 T   (d) (97)1/4 T

Solution. In the steady state, absorption and emission by the middle plate will be the same. Thus σA(3T)4 − σA(T′)4 = σA(T′)4 − σA(2T)4 ⇒ 2T′4 = (81 + 16)T4 ⇒ T′ = (97/2)1/4 T. Answer: (c).

Teacher's Note: Net radiation in from the hotter plate equals net radiation out to the colder plate.

Exam Note: Write both fluxes as σ(T14 − T24).

Question 1.2.13. Two nonreactive monatomic ideal gases have their atomic masses in the ratio 2 : 3. The ratio of their partial pressures when enclosed in a vessel kept at a constant temperature is 4 : 3. The ratio of their densities is
(a) 1 : 4   (b) 1 : 2   (c) 6 : 9   (d) 8 : 9

Solution. By the gas laws: pV = nRT = (m/M)RT ⇒ pM = (m/V)RT = ρRT. Therefore ρ1/ρ2 = (p1/p2) × (M1/M2) = 4/3 × 2/3 = 8/9. Answer: (d) 8 : 9.

Teacher's Note: ρ = pM/RT at the same temperature, so density ratio is pressure ratio times mass ratio.

Exam Note: Gases share the same T and V.

Question 1.2.14. Two rectangular blocks having identical dimensions can be arranged either in Configuration I or in Configuration II, as shown in the figure. One of the blocks has the thermal conductivity K and the other, 2K. The temperature difference between the ends along the x-axis is the same in both the configurations. It takes 9 s to transport a certain amount of heat from the hot end to the cold end in Configuration I. The time required in transporting the same amount of heat in Configuration II is
(Figure: Configuration I: blocks K and 2K placed side by side in series along the x-axis. Configuration II: blocks K and 2K placed one above the other, i.e. in parallel along the x-axis.)
(a) 2.0 s   (b) 3.0 s   (c) 4.5 s   (d) 6.0 s

Solution. Let the thermal resistances in the two configurations be R1 and R2. In Configuration I, R1 = L/KA + L/2KA = 3L/2KA. In Configuration II, 1/R2 = 1/(L/KA) + 1/(L/2KA) = 3KA/L ⇒ R2 = L/3KA. Since ΔQ1 = ΔQ2, (Δθ/R1)t1 = (Δθ/R2)t2 ⇒ t2 = (R2/R1)t1 = 2 s. Answer: (a) 2.0 s.

Teacher's Note: Configuration I is series, II is parallel; for equal heat and ΔT, time scales with resistance.

Exam Note: Same heat and ΔT: time ∝ resistance.

Question 1.2.15. A water cooler of storage capacity 120 litres can cool water at a constant rate of P. In a closed circulation system (as shown schematically in this figure), the water from the cooler is used to cool an external device that generates constantly 3 kW of power (thermal load). The temperature of the water fed into the device cannot exceed 30 °C and the entire 120 litres of water is initialy cooled to 10 °C. The entire system is thermally insulated. The minimum value of P for which the device can be operated for 3 hours (taking the specific heat capacity of water = 4.2 kJ kg−1 K−1 and the density of water = 1000 kg m−3) is
(a) 1600 W   (b) 2067 W   (c) 2533 W   (d) 3933 W

Solution. Heat generated = (3 kW)(3 h) = 3 × 103 × 3 × 3600 J = 324 × 105 J. Heat absorbed by water = mcwΔθ = (120)(4200)(20) J = 100.8 × 105 J. Heat absorbed by the coolant: Pt = (324 × 105 − 100.8 × 105) J ⇒ P = 223.2 × 105 J/(3 × 3600 s) = 2067 W. Answer: (b).

Teacher's Note: Total heat from device minus what the stored water can absorb (10 °C to 30 °C) is the cooler’s job.

Exam Note: Water absorbs 20 K rise, then cooler removes the rest.

Question 1.2.16. A gas is enclosed in a cylinder with a movable frictionless piston. Its initial thermodynamic state at the pressure pi = 105 Pa and the volume Vi = 10−3 m3 changes to a final state at pf = (1/32) × 105 Pa and Vf = 8 × 10−3 m3 in an adiabatic quasi-static process, such that p3V5 = constant. Consider another thermodynamic process that brings the system from the same initial state to the same final state in two steps: an isobaric expansion at pi followed by an isochoric process at Vf. The amount of the heat supplied to the system in the two-step process is approximately
(a) 112 J   (b) 294 J   (c) 588 J   (d) 813 J

Solution. Given p3V5 = constant ⇒ pV5/3 = constant, so γ = 5/3 (monatomic gas). Isobaric process AB: ΔQ1 = nCpΔT = n(5/2)RΔT = (5/2)pΔV = (5/2)(105 Pa)(7 × 10−3 m3) = 1750 J (heat absorbed). Isochoric process BC: ΔQ2 = nCVΔT = (3/2)(VΔp) = (3/2)(8 × 10−3 m3)(1/32 − 1) × 105 Pa = −1162.5 J (heat expelled). So the net heat supplied to the system is 1750 J + (−1162.5 J) = 587.5 J ≈ 588 J. Answer: (c).

Teacher's Note: Find γ from p3V5; add isobaric heat and isochoric heat (negative).

Exam Note: Sum 1750 J and −1162.5 J.

Question 1.2.17. Parallel rays of light of the intensity I = 912 W m−2 are incident on a spherical black body kept in the surroundings of temperature 300 K. Take the Stefan–Boltzmann constant σ = 5.7 × 10−8 W m−2 K−4, and assume that the energy exchange with the surroundings is only through radiations. The final steady-state temperature of the black body is close to
(a) 330 K   (b) 660 K   (c) 990 K   (d) 1550 K

Solution. In the steady state, the rate of energy loss = the rate of energy incidence ⇒ πR2·I = σ·4πR2·(T4 − T04) ⇒ I = 4σ(T4 − T04) ∴ T4 − T04 = 40 × 108 K4 ⇒ T4 − 81 × 108 K4 = 40 × 108 K4 ⇒ T4 = 121 × 108 K4 ⇒ T ≈ 330 K. Answer: (a) 330 K.

Teacher's Note: Absorbs over cross-section πR2, radiates over 4πR2; net emission uses T4 − T04.

Exam Note: Cross-section for absorption differs from emitting area.

Question 1.2.18. The ends Q and R of two thin wires PQ and RS are soldered (joined) together. Initially each of the wires has a length of 1 m at 10 °C. Now the end P is maintained at 10 °C, while the end S is heated and maintained at 400 °C. The system is thermally insulated from its surroundings. If the thermal conductivity of the wire PQ is twice that of the wire RS, and the coefficient of linear thermal expansion for PQ is 1.2 × 10−5 K−1, the change in the length of the wire PQ is
(Figure: wire PQ (1 m, conductivity 2k, expansion α1) joined at QR (140 °C) to wire RS (1 m, conductivity k, expansion α2); P at 10 °C and S at 400 °C.)
(a) 0.78 mm   (b) 0.90 mm   (c) 1.56 mm   (d) 2.34 mm

Solution. For an element dx at a distance x from the end P, the change in length dl = α1dx(θ − 10), Δl = ∫dl, where θ is the temperature at the distance x from the end P. Junction temperature: 2k(θQ − 10) = k(400 − θQ) gives θQ = 140 °C. Temperature gradient in PQ = (θ − 10)/x = (140 − 10)/1 ⇒ θ = 130x + 10. Δl = ∫01(130x)α1dx = 130α1[x2/2]01 = 65 × 1.2 × 10−5 m = 78.0 × 10−5 m = 0.78 mm. Answer: (a).

Teacher's Note: Steady conduction gives a linear temperature profile; integrate expansion over each element.

Exam Note: Find the junction temperature from equal heat flow.

Question 1.2.19. An ideal gas is expanding such that pT2 = constant. The coefficient of volume expansion for the gas is
(a) 1/T   (b) 2/T   (c) 3/T   (d) 4/T

Solution. Given pT2 = constant. But pV = nRT ∴ (nRT/V)T2 = constant ⇒ T3 = KV …(1). Differentiating, 3T2dT = KdV …(2). Dividing (2) by (1), dV/V = 3dT/T ∴ γ = (1/V)(dV/dT) = 3/T. Answer: (c).

Teacher's Note: Eliminate p using pV = nRT to get V ∝ T3.

Exam Note: Coefficient of expansion = (1/V)dV/dT.

1.3 Sound Waves

Question 1.3.1. Two pulses in a stretched string whose centres are initially 8 cm apart are moving towards each other, as shown in the figure. The speed of each pulse is 2 cm s−1. After 2 s, the total energy of the pulses will be
(Figure: two pulses on a string, one upward and one downward, centres 8 cm apart, moving towards each other.)
(a) zero   (b) purely kinetic   (c) purely potential   (d) partly kinetic and partly potential

Solution. After 2 s, the pulses will overlap completely (each has moved 4 cm). The string becomes straight and therefore does not have any potential energy. Its entire energy must be kinetic. Answer: (b) purely kinetic.

Teacher's Note: Opposite pulses cancel displacement completely, leaving a straight string with moving points.

Exam Note: Energy is not zero; it is all kinetic.

Question 1.3.2. A point mass is subjected to two simultaneous sinusoidal displacements in the x-directions: x1(t) = A sin ωt and x2(t) = A sin(ωt + 2π/3). Adding a third sinusoidal displacement x3(t) = B sin(ωt + φ) brings the mass to a complete rest. The values of B and φ are respectively
(a) √2 A and 3π/4   (b) A and 4π/3   (c) √3 A and 5π/6   (d) A and π/3

Solution. Conclude from the vector (phasor) triangle: the three phasors form an equilateral triangle with exterior angles 2π/3, so x1 + x2 has amplitude A and phase π/3, and the third must have amplitude B = A and phase π/3 + π = 4π/3. Answer: (b) A and 4π/3.

Teacher's Note: Three equal phasors summing to zero must be 120° apart; the third lies at 4π/3.

Exam Note: Draw the phasor triangle.

Question 1.3.3. The ends of a stretched wire of length L are fixed at x = 0 and x = L. In one experiment, the displacement of the wire is y1 = A sin(πx/L) sin ωt and the energy is E1, and in another experiment the displacement is y2 = A sin(2πx/L) sin 2ωt and the energy is E2. Then
(a) E2 = E1   (b) E2 = 2E1   (c) E2 = 4E1   (d) E2 = 16E1

Solution. A stationary wave has the equation of the form y = A sin kx sin ωt. For y1, k1 = π/L and ω1 = ω, so v1 = ω1/k1 = ωL/π. For y2, k2 = 2π/L and ω2 = 2ω, so v2 = ω2/k2 = ωL/π = v1. Thus the wave velocities are the same in both the cases, and they have the same amplitude. The frequency for y2 is twice the frequency for y1. Now, since energy ∝ (frequency)2, E2 = 4E1. Answer: (c).

Teacher's Note: Energy of a vibrating string at fixed amplitude is proportional to frequency squared.

Exam Note: Frequency doubles, so energy quadruples.

Question 1.3.4. Two vibrating strings made of the same material but of lengths L and 2L have the radii 2r and r respectively. They are stretched under the same tension. Both the strings vibrate in their fundamental modes — the one of length L with frequency ν1 and the other with frequency ν2. The ratio ν1/ν2 is equal to
(a) 2   (b) 4   (c) 8   (d) 1

Solution. ν = (1/2l)√(T/m) = (1/2l)√(T/Aρ) = (1/2l)√(T/πR2ρ) = (1/2lR)√(T/πρ). As T and ρ are the same for both wires, ν ∝ 1/(lR). Here lR = L × 2r = 2L × r. ∴ ν1 = ν2. Answer: (d).

Teacher's Note: Frequency depends on 1/(length × radius) for the same tension and material.

Exam Note: L × 2r equals 2L × r.

Question 1.3.5. A sonometer wire resonates with a given tuning fork, forming standing waves with five antinodes between the two bridges when a mass of 9 kg is suspended from the wire. When this mass is replaced by a mass M, the wire resonates with the same tuning fork, forming three antinodes for the same positions of the bridges. The value of M is
(a) 25 kg   (b) 5 kg   (c) 12.5 kg   (d) 1/25 kg

Solution. The frequency of vibration of a string is given by n = (N/2l)√(T/m), where N = number of loops (or segments) = number of antinodes. The other symbols have their usual meanings. Here n = (5/2l)√(9g/m) = (3/2l)√(Mg/m) or M = 25 kg. Answer: (a) 25 kg.

Teacher's Note: Fixed frequency and length: N√T is constant, so tension ∝ 1/N2.

Exam Note: Five loops to three loops raises tension 25/9 times.

Question 1.3.6. A student is performing an experiment with a resonance column. The diameter of the column tube is 4 cm. The frequency of the tuning fork is 512 Hz. The air temperature is 38 °C in which the speed of sound is 336 m s−1. The zero of the metre scale coincides with the top end of the resonance column tube. When the first resonance occurs, the reading of the water level in the column is
(a) 14.0 cm   (b) 15.2 cm   (c) 16.4 cm   (d) 17.6 cm

Solution. λ/4 = L + e ⇒ L = λ/4 − e = v/4f − 0.6R = 16.4 cm − 1.2 cm = 15.2 cm. Answer: (b) 15.2 cm.

Teacher's Note: First resonance is λ/4 minus end correction 0.6R, with R = 2 cm.

Exam Note: Do not forget the end correction.

Question 1.3.7. A hollow pipe of length 0.8 m is closed at one end. At its open end, a 0.5-m-long uniform string is vibrating in its second harmonic and it resonates with the fundamental frequency of the pipe. If the tension in the wire is 50 N and the speed of sound is 320 m s−1, the mass of the string is
(a) 5 grams   (b) 10 grams   (c) 20 grams   (d) 40 grams

Solution. For a closed pipe the fundamental is V/(4lpipe) = 320/(4 × 0.8) = 100 Hz. The string’s second harmonic is 2(1/(2lstring))√(T/m) = 2√(50/m) with m the mass per unit length, so 2√(50/m) = 100 ⇒ m = 0.02 kg m−1. Mass of the string = m·ls = 0.02 × 0.5 = 0.01 kg = 10 g. Answer: (b) 10 grams.

Teacher's Note: Closed-pipe fundamental is v/4l; match to the string’s second harmonic √(T/μ)/l.

Exam Note: Convert mass per length to total mass.

Question 1.3.8. A train moves towards a stationary observer with a speed of 34 m s−1. The train sounds a whistle and its frequency registered by the observer is f1. If the train’s speed is reduced to 17 m s−1, the frequency registered is f2. If the speed of sound is 340 m s−1 then the ratio f1/f2 is
(a) 18/19   (b) 1/2   (c) 2   (d) 19/18

Solution. no = nsV/(V − vs). Here, f1 = nsV/(340 − 34) and f2 = nsV/(340 − 17). ∴ f1/f2 = (340 − 17)/(340 − 34) = 323/306 = 19/18. Answer: (d) 19/18.

Teacher's Note: Source approaching: f = f0V/(V − vs); higher speed gives higher frequency.

Exam Note: Use (V − vs) in the denominator.

Question 1.3.9. A siren placed at a railway platform is emitting sound waves of 5 kHz frequency. A passenger sitting in a moving train A records a frequency of 5.5 kHz while the train approaches the siren. During his return journey by a different train B, he records a frequency of 6.0 kHz while approaching the same siren. The ratio of the velocity of the train B to that of the train A is
(a) 242 : 252   (b) 2 : 1   (c) 5 : 1   (d) 11 : 6

Solution. When an observer approaches a stationary source, which is emitting sound waves of frequency ns, he hears a frequency n = ns(1 + v/V), where v = velocity of the observer and V = velocity of sound. For A, n = 5.5 kHz = (5 kHz)(1 + vA/V), so vA/V = 0.1. For B, 6 kHz = (5 kHz)(1 + vB/V), so vB/V = 0.2. ∴ vB/vA = 2, or vB : vA = 2 : 1. Answer: (b).

Teacher's Note: Moving observer: f = f0(1 + v/V); fractional rise gives v/V directly.

Exam Note: Take the ratio of the two v/V values.

Question 1.3.10. A police car with a siren of frequency 8 kHz is moving with a uniform velocity of 36 km h−1 towards a tall building which reflects the sound waves. The speed of sound in air is 320 m s−1. The frequency of the siren heard by the car driver is
(a) 8.50 kHz   (b) 8.25 kHz   (c) 7.75 kHz   (d) 7.50 kHz

Solution. f′ = ((v + vo)/(v − vs))f = ((320 + 10)/(320 − 10))(8 × 103 Hz) = 8.5 kHz (36 km h−1 = 10 m s−1; the car is both source and observer moving towards the wall). Answer: (a) 8.50 kHz.

Teacher's Note: Car acts as source then as observer moving toward the wall; both speeds enter once.

Exam Note: Convert 36 km/h to 10 m/s first.

Question 1.3.11. A massless rod is suspended by two identical strings, AB and CD, of equal lengths. A block of mass m is suspended from the point O such that BO = x, as shown in the figure. Further, it is observed that the frequency of the first harmonic (fundamental frequency) in AB is equal to the 2nd harmonic in CD. Then the length of BO is
(Figure: rod BD of length L hung from the ceiling by vertical strings AB at the left end and CD at the right end; the block m hangs from O at distance x from B.)
(a) L/5   (b) 4L/5   (c) 3L/4   (d) L/4

Solution. T1 + T2 = mg and T1x = T2(L − x). f1 = (1/2l)√(T1/μ) and f2 = (2/2l)√(T2/μ), where μ = linear mass density and f1 = f2. ∴ T1 = 4T2 or T1x = (T1/4)(L − x) or x = L/5. Answer: (a) L/5.

Teacher's Note: Equal frequencies force T1 = 4T2; torque balance about the block then gives x.

Exam Note: Torque balance: T1x = T2(L − x).

Question 1.3.12. In the experiment to determine the speed of sound using a resonance column,
(a) the prongs of the tuning fork are kept in a vertical plane
(b) the prongs of the tuning fork are kept in a horizontal plane
(c) in one of the two resonances observed, the length of the resonating air column is close to the wavelength of sound in air
(d) in one of the two resonances observed, the length of the resonating air column is close to half the wavelength of sound in air

Solution. The prongs of the tuning fork are kept in a vertical plane in order to set up longitudinal standing waves in the air column. Answer: (a).

Teacher's Note: Vertical prongs vibrate along the tube axis, setting up longitudinal air-column waves.

Exam Note: Plane of prongs decides which waves are excited.

Question 1.3.13. A vibrating string of length l under the tension T resonates with a mode corresponding to the first overtone (third harmonic) of an air column of length 75 cm inside a tube closed at one end. The string also generates 4 beats per second when excited with a tuning fork of frequency n. When the tension of the string is slightly increased, the beat frequency reduces to 2 beats per second. Assuming the speed of sound in air to be 340 m s−1, the frequency n of the tuning fork is
(a) 344 Hz   (b) 336 Hz   (c) 117.3 Hz   (d) 109.3 Hz

Solution. The frequency of the third harmonic of the closed pipe is f = 3(v/4l) = 3 × 340/(4 × 0.75) = 340 Hz. Since the increase in tension (which raises the string’s frequency above 340 Hz) reduces the beat frequency from 4 s−1 to 2 s−1, n is above the string’s frequency: n − 340 Hz = 4 Hz ⇒ n = 344 Hz. Answer: (a) 344 Hz.

Teacher's Note: Raising tension raises string frequency; falling beats mean the fork is the higher frequency.

Exam Note: Reason out the sign of the beat difference.

Question 1.3.14. A transverse sinusoidal wave moves along a string in the positive x-direction at a speed of 10 cm s−1. The wavelength of the wave is 0.5 m and its amplitude is 10 cm. At a particular time t, the snapshot of the wave is shown in the figure. The velocity of the point P when its displacement is 5 cm is
(Figure: sinusoidal snapshot; P lies on the descending slope just after the first crest.)
(a) (√3π/50) j m s−1   (b) −(√3π/50) j m s−1   (c) (√3π/50) i m s−1   (d) −(√3π/50) i m s−1

Solution. y = A sin(ωt ± φ). Since A = 10 cm and y = 5 cm, sin(ωt ± φ) = 1/2 = sin 30° ⇒ ωt ± φ = 30°. Here, ω = 2π/T = 2π(V/λ) = 2π(10 cm s−1/50 cm) = 2π/5 rad s−1. Therefore the velocity of the point P is vP = dy/dt = Aω cos(ωt ± φ) = (10 cm)(2π/5 s−1)(cos 30°) = 2π√3 cm s−1 = (π√3/50) m s−1. ∴ vP = (π√3/50) j m s−1. Answer: (a).

Teacher's Note: Particle velocity is Aω cos(phase); direction is along the y-axis, not the wave direction.

Exam Note: Particle motion is transverse: use j, not i.

1.4 Electrostatics

Question 1.4.1. Three positive charges each having the value q are placed at the vertices of an equilateral triangle. The resulting lines of force should be sketched as
(Figure: four field-line sketches (a)–(d). (a) closed loops around the triangle; (b) radial lines of a single central charge; (c) lines leaving each of the three charges and bending away from each other, with no line joining two charges; (d) concentric closed circles around each charge.)

Solution. The tangent drawn to a line of force at any point on it must give the direction of the electric intensity at that point. Consider a point midway between any two of the charges. Here, the resultant intensity is only the intensity due to the third charge and must point away from the third charge. This is satisfied only in the sketch (c). Answer: (c).

Teacher's Note: Field direction at the midpoint of two equal charges points away from the third charge.

Exam Note: Check field lines at a symmetric midpoint.

Question 1.4.2. A uniformly charged thin spherical shell of radius R carries a uniform surface charge density of σ per unit area. It is made of two hemispherical shells, held together by pressing them with a force F (see the figure). F is proportional to
(a) (1/ε0)σ2R2   (b) (1/ε0)σ2R   (c) (1/ε0)σ2/R   (d) (1/ε0)σ2/R2

Solution. Only the option (a) has the dimensions of force. (Check: electrostatic pressure σ2/2ε0 acting over the cross-section πR2 gives F = πR2σ2/2ε0 ∝ σ2R2/ε0.) Answer: (a).

Teacher's Note: Outward electric pressure σ2/2ε0 times the projected area πR2.

Exam Note: Use dimensions to eliminate options quickly.

Question 1.4.3. A tiny spherical oil drop carrying a net charge q is balanced in still air with a vertical uniform electric field of strength (81π/7) × 105 V m−1. When the field is switched off, the drop is observed to fall with a terminal velocity of 2 × 10−3 m s−1. Given g = 9.8 m s−2, viscosity of the air = 1.8 × 10−5 N s m−2 and density of oil = 900 kg m−3, the magnitude of q is
(a) 1.6 × 10−19 C   (b) 3.2 × 10−19 C   (c) 4.8 × 10−19 C   (d) 8.0 × 10−19 C

Solution. In balance qE = (4/3)πr3ρg, and at terminal velocity (4/3)πr3ρg = 6πηrv. From the second relation r2 = 9ηv/(2ρg) = 1.837 × 10−11 m2, so r = 4.29 × 10−6 m. Then q = 6πηrv/E = 8.0 × 10−19 C (verified numerically). Answer: (d) 8.0 × 10−19 C.

Teacher's Note: Balance gives qE = weight; terminal velocity gives radius via Stokes’ law.

Exam Note: Find r from Stokes’ law before q.

Question 1.4.4. Consider the electric field E = E0x, where E0 is a constant. The flux through the shaded area shown in the figure due to this field is
(Figure: a shaded parallelogram with vertices (0, 0, 0), (0, a, 0), (a, a, a) and (a, 0, a).)
(a) 2E0a2   (b) √2 E0a2   (c) E0a2   (d) E0a2/√2

Solution. Flux = (field) × (projected area) = E0a2, since the projection of the parallelogram on the yz-plane is a square of side a. Answer: (c).

Teacher's Note: Only the area projected perpendicular to the field counts; this is the a × a square.

Exam Note: Project onto the plane normal to E.

Question 1.4.5. Two large vertical and parallel metal plates having a separation of 1 cm are connected to a d.c. voltage source of potential difference X. A proton is released from the rest, midway between the two plates. It is found to move at 45° to the vertical just after the release. Then X is nearly
(a) 1 × 10−5 V   (b) 1 × 10−7 V   (c) 1 × 10−9 V   (d) 1 × 10−10 V

Solution. At 45°, the electric force equals the weight: qE = mg ⇒ eE = mpg ⇒ (1.602 × 10−19 C)(X/10−2 m) = (1.672 × 10−27 kg)(10 m s−2) ⇒ X ≈ 1 × 10−9 V. Answer: (c).

Teacher's Note: Motion at 45° means horizontal electric force equals the vertical weight.

Exam Note: E = X/d with d = 1 cm.

Question 1.4.6. Consider a thin spherical shell of radius R with its centre at the origin, carrying a uniform positive surface charge density. The variation of the magnitude of the electric field |E(r)| and the electric potential V(r) with the distance r from the centre is best represented by which graph?
(Figure: four graphs (a)–(d) of |E(r)| and V(r) against r with R marked. In (d) the potential (dashed) is constant up to R and then falls as 1/r, while the field (solid) is zero inside R, jumps to its maximum at R and then falls as 1/r2; in (a), (b), (c) the field is non-zero inside or the potential is not constant inside.)

Solution. For a uniformly charged thin shell, V = KQ/R (constant) for r < R and V ∝ 1/r for r > R; E = 0 for r < R, ER = KQ/R2 at the surface, and E ∝ 1/r2 for r > R. Answer: (d).

Teacher's Note: Inside a shell E = 0 and V is constant; outside it behaves as a point charge.

Exam Note: Potential is continuous; field jumps at the surface.

Step-by-Step SB Mathur Solutions for JEE Math

Access JEE Mathematics Solutions

Explore reliable mathematical solutions for SB Mathur Physics Solutions Chapter 1 Multiple-Choice Questions Type 1 Part 1 tailored for JEE learners. Utilizing these complete exercise answers ensures your preparation aligns exactly with standard academic requirements.

Mastering Core Concepts with SB Mathur Solutions

Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.

Additional Study Materials for 2026

In addition to these SB Mathur Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.

FAQs

What are these SB Mathur Solutions for JEE Physics?

They are chapter-wise solved questions from the SB Mathur book for JEE Physics. Each answer is explained step by step so you can check your work and revise.

Are the SB Mathur JEE Physics Solutions free to read?

Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.

How should I use these SB Mathur solutions for JEE Physics?

Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.

Will practising SB Mathur JEE Physics questions help in exams?

Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.

Are these solutions arranged chapter by chapter?

Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.

Which session are these JEE Physics Solutions for?

They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.