Download JEE Physics SS Krotov Textbook Solutions: Problems 2.24 to 4.18
Review structured textbook solutions for JEE Physics Problems 2.24 to 4.18 prepared by SS Krotov. Built according to modern educational guidelines for the 2026 academic year, these downloadable answers support daily revision and mathematical accuracy.
Access SS Krotov Textbook Answers and Solutions
Access the complete solution PDF for JEE Physics below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
S Krotov Physics Solutions - Problems 2.24 to 4.18
Chapter 2: Heat and Molecular Physics
Question 2.24. A cylinder with a movable piston contains air under a pressure p1 and a soap bubble of radius r. The surface tension is σ, and the temperature T is maintained constant. Determine the pressure p2 to which the air should be compressed by slowly pulling the piston into the cylinder for the soap bubble to reduce its size by half.
Solution. The condition of equilibrium for the soap bubble film is that the air pressure pbubl is the sum of the external pressure p1 and the excess pressure 4σ/r due to surface tension. There are two air-soap film interfaces in the soap bubble, each producing a pressure 2σ/r, so the excess pressure is 2 × 2σ/r = 4σ/r. Hence pbubl = p1 + 4σ/r.
After the radius is reduced by half, the pressure produced by surface tension becomes 8σ/r. The temperature is constant, so by Boyle's law a decrease in the volume of the bubble by a factor of eight (its radius has decreased by half) leads to an eightfold increase in the air pressure in the bubble (it becomes 8pbubl), so that 8pbubl = p2 + 8σ/r.
Substituting pbubl from the first equation: p2 = 8p1 + 24σ/r.
Teacher's Note: A soap bubble has two surfaces, so excess pressure is 4σ/r; halving r multiplies volume pressure by eight.
Exam Note: Remember the factor 4σ/r for a soap film, not 2σ/r.
Question 2.26. A thermally insulated vessel contains two liquids with initial temperatures T1 and T2 and specific heats c1 and c2, separated by a nonconducting partition. The partition is removed, and the difference between the initial temperature of one of the liquids and the temperature T established in the vessel turns out to be equal to half the difference between the initial temperatures of the liquids. Determine the ratio m1/m2 of the masses of the liquids.
Solution. Let T be the temperature of the mixture. Since the vessel is thermally insulated (ΔQ = 0), c1m1(T − T1) + c2m2(T − T2) = 0, whence m1/m2 = (c2/c1)(T − T2)(T1 − T)−1.
By hypothesis, 2(T1 − T) = T1 − T2, and hence T − T2 = T1 − T, so the ratio (T − T2)/(T1 − T) = 1. Therefore m1/m2 = c2/c1, i.e., the ratio of the masses of these liquids is inverse to the ratio of their specific heats.
Teacher's Note: Heat lost equals heat gained; equal temperature changes on both sides mean m c is the same for both liquids.
Exam Note: Start from ΣmcΔT = 0 for an insulated mixture.
Question 2.27. Water at 20°C is poured into a test tube whose bottom is immersed in a large amount of water at 80°C. As a result, the water in the test tube is heated to 80°C during a time t1. Then water at 80°C is poured into the test tube whose bottom is immersed in a large amount of water at 20°C. The water in the test tube is cooled to 20°C during a time t2. What time is longer, t1 or t2?
Solution. In the former case, the water in the test tube is mainly heated due to convection, since warm water is lighter than cold water. In the latter case, water is cooled only as a result of heat exchange between water layers in the test tube. Since the conditions of heat exchange between the test tube and outer water remain the same, t1 < t2.
It should be noted that if we change the parameters of the problem (20°C → 0°C and 80°C → 4°C), we shall obtain a reverse answer. The reason lies in the anomaly of water: in the temperature interval from 0 to 4°C, cold water is lighter than warm water.
Teacher's Note: Heating from below drives fast convection; cooling from below leaves only slow conduction between layers.
Exam Note: State the convection argument, not just the inequality.
Question 2.28. The same mass of water is poured into two identical light metal vessels. A heavy ball (whose mass is equal to the mass of water and whose density is much higher than that of water) is immersed on a thin non-conducting thread in one of the vessels so that it is at the centre of the volume of the water in the vessel. The vessels are heated to the boiling point of water and left to cool. The time of cooling for the vessel with the ball to the temperature of the ambient is known to be k times as long as the time of cooling for the vessel without a ball. Determine the ratio cb/cw of the specific heats of the ball material and water.
Solution. The heat flux per unit time through the surface of contact with the ambient depends on the temperature difference: ΔQ/Δt = αF(Tves − T), where Tves is the temperature of the vessel, T is the temperature of the ambient, and F is a certain function of temperature. The coefficient α is determined by the conditions at the contact with the ambient, which are identical for the two vessels, so α is the same in both cases.
For the vessel with water: ΔQ1 = (Mwcw + mvescves)ΔTves. For the vessel with water and the ball: ΔQ2 = (Mwcw + mbcb + mvescves)ΔTves. By hypothesis mves << Mw, mb = Mw, and cves << cw, so ΔQ1 = MwcwΔTves and ΔQ2 = Mw(cw + cb)ΔTves.
The same temperature change occurs during different time intervals Δt1 and Δt2: ΔTves/[F(Tves − T)] = (α/(Mwcw))Δt1 and ΔTves/[F(Tves − T)] = (α/(Mw(cw + cb)))Δt2. Hence Δt1/Δt2 = cw/(cw + cb).
Therefore for the total cooling times, t2/t1 = (cw + cb)/cw = k, whence cb/cw = k − 1.
Teacher's Note: Same heat-loss law for both vessels, so cooling time is proportional to total heat capacity; the ball adds m cb.
Exam Note: Link time ratio to heat capacity ratio; then subtract 1.
Question 2.29. Two identical thermally insulated cylindrical calorimeters of height h = 75 cm are filled to one-third. The first calorimeter is filled with ice formed as a result of freezing water poured into it, and the second is filled with water at Tw = 10°C. Water from the second calorimeter is poured into the first one, and as a result it becomes to be filled to two-thirds. After the temperature has been stabilized in the first calorimeter, its level of water increases by Δh = 0.5 cm. The density of ice is ρice = 0.9ρw, the latent heat of fusion of ice is λ = 340 kJ/kg, the specific heat of ice is cice = 2.1 kJ/(kg·K), and the specific heat of water is cw = 4.2 kJ/(kg·K). Determine the initial temperature Tice of ice in the first calorimeter.
Solution. If the level of water in the calorimeter has become higher, it means that a part of water has frozen (the volume of water increases during freezing). On the other hand, some amount of water has not frozen, since otherwise its volume would have increased by a factor of ρw/ρice ≈ 1.1, and the level would have increased by (h/3)(1.1 − 1) ≈ 2.5 cm, while by hypothesis Δh = 0.5 cm. Thus, the temperature established in the calorimeter is 0°C.
Using this condition: cwmw(Tw − 0°C) = −λΔm + cicemice(0°C − Tice) ....(1), where Δm is the mass of frozen water and Tice is the initial temperature of ice.
The volume of water increases as a result of freezing by a factor ρw/ρice, hence ΔhS = (ρw/ρice − 1)Δm/ρw ....(2), where S is the cross-sectional area of the calorimeter. Substituting Δm from (2) into (1) and using mw = (h/3)ρwS and mice = (h/3)ρiceS, we obtain
Tice = −(λ/cice)(3Δh/h)(ρw/(ρw − ρice)) − (cw/cice)(ρw/ρice)Tw ≈ −54°C.
Check: the first term = (340/2.1)(0.02)(10) = 32.4 and the second = 2 × 1.11 × 10 = 22.2, total 54.6, i.e. about −54°C to −55°C.
Teacher's Note: Small level rise means partial freezing, so final temperature is 0°C; then balance heats.
Exam Note: Justify 0°C from the small level rise before calculating.
Question 2.34. A long vertical brick duct is filled with cast iron. The lower end of the duct is maintained at a temperature T1 > Tmelt (Tmelt is the melting point of cast iron), and the upper end at a temperature T2 < Tmelt. The thermal conductivity of molten (liquid) cast iron is k times higher than that of solid cast iron. Determine the fraction of the duct filled with molten metal.
Solution. Since the lower end is at T1, higher than the melting point, the cast iron at the bottom will be molten. The temperature at the interface between the molten and solid cast iron is equal to Tmelt. Since the end temperatures are constant, the heat transferred per unit time through any cross section is the same: the heat flux through the molten and solid cast iron must be equal (heat transfer through the walls is neglected).
The heat flux is proportional to the thermal conductivity, the cross-sectional area, and the temperature difference per unit length. Let ℓ1 be the length of the lower molten part and ℓ2 the length of the upper solid part. Then xliq(T1 − Tmelt)/ℓ1 = xsol(Tmelt − T2)/ℓ2, where xliq and xsol are the thermal conductivities of liquid and solid cast iron. With xliq = kxsol: ℓ1 = ℓ2k(T1 − Tmelt)/(Tmelt − T2).
The total length of the duct is ℓ1 + ℓ2. Therefore ℓ1/(ℓ1 + ℓ2) = k(T1 − Tmelt) / [k(T1 − Tmelt) + (Tmelt − T2)].
Corrected: the book prints the denominator as (ℓ1 − ℓ2); it must be ℓ1 + ℓ2, as the final expression shows.
Teacher's Note: In steady state the heat flux is equal in both layers, and the interface sits at the melting point.
Exam Note: Equate fluxes through liquid and solid parts; interface is at Tmelt.
Question 2.36. A bucket contains a mixture of water and ice of mass m = 10 kg. The bucket is brought into a room, after which the temperature of the mixture is immediately measured. The obtained T(τ) dependence is plotted in the figure (temperature stays at 0°C for the first 50 minutes, then rises, reaching 2°C at 60 minutes). The specific heat of water is cw = 4.2 J/(g·K) and the latent heat of fusion of ice is λ = 340 kJ/kg. Determine the mass mice of ice in the bucket at the moment it is brought into the room, neglecting the heat capacity of the bucket.
Solution. It follows from the graph that during the first 50 minutes the temperature of the mixture does not change and is equal to 0°C. The heat received by the mixture from the room during this time is spent to melt ice. In 50 minutes, the whole ice melts and the temperature of water begins to rise. In 10 minutes (from τ1 = 50 min to τ2 = 60 min), the temperature increases by ΔT = 2°C. The heat supplied to the water from the room during this time is θ = cwmwΔT = 84 kJ. Therefore the heat received by the mixture during the first 50 minutes is Q = 5q = 420 kJ. This heat was spent for melting ice of mass mice: Q = λmice. Thus mice = Q/λ ≈ 1.2 kg.
Check: 4.2 kJ/(kg·K) × 10 kg × 2 K = 84 kJ; 5 × 84 = 420 kJ; 420/340 = 1.235 kg.
Teacher's Note: Flat 0°C part melts ice; the sloped part gives heating rate.
Exam Note: Constant heating rate: 10 min is 84 kJ.
Question 2.39. A thin U-tube sealed at one end consists of three bends of length ℓ = 250 mm each, forming right angles. The vertical parts of the tube are filled with mercury to half the height (figure). All of the mercury can be displaced from the tube by heating slowly the gas in the sealed end of the tube, which is separated from the atmospheric air by mercury. Determine the work A done by the gas thereby if the atmospheric pressure is p0 = 105 Pa, the density of mercury is ρmer = 13.6 × 103 kg/m3, and the cross-sectional area of the tube is S = 1 cm2. (Figure: a U-shaped tube made of three segments each of length ℓ, i.e. a horizontal bottom of length ℓ and two vertical arms of height ℓ, closed at the top of the left arm; mercury fills the horizontal part and half of each vertical arm.)
Solution. The work A done by the gas is the sum of two components: the work A1 done against atmospheric pressure and the work A2 done against gravity. The mercury-gas interface is shifted upon the complete displacement of mercury by 2ℓ + ℓ/2 = (5/2)ℓ, hence A1 = (5/2)p0Sℓ.
The work A2 against gravity equals the change in potential energy of mercury. The whole of the mercury rises as a result of its displacement by ℓ relative to the horizontal part of the tube. This quantity should be regarded as the final height of the centre of mass of mercury. The initial position of the centre of mass of mercury is h0 = ℓ/8. Hence A2 = Mg(ℓ − ℓ/8) = (7/8)Mgℓ, where M = 2ℓSρmer is the mass of mercury.
Finally, A = A1 + A2 = (5/2)p0Sℓ + (7/4)ρmergSℓ2 ≈ 7.7 J.
Check: A1 = 2.5 × 105 × 10−4 × 0.25 = 6.25 J; M = 0.68 kg, A2 = (7/8)(0.68)(9.8)(0.25) = 1.46 J; total 7.71 J.
Teacher's Note: Gas work = work against atmosphere plus the gain in mercury potential energy (centre of mass rise).
Exam Note: Show both parts, then add the numbers: 6.25 + 1.46 J.
Question 2.41. A thin-walled cylinder of mass m, height h, and cross-sectional area S is filled with a gas and floats on the surface of water (figure: an open-bottomed cylinder floating with its lower part immersed). As a result of leakage from the lower part of the cylinder, the depth of its submergence has increased by Δh. Determine the initial pressure p1 of the gas in the cylinder if the atmospheric pressure is p0, and the temperature remains unchanged.
Solution. Let the cylinder be filled with water to a level x from the base. The change in buoyancy is equal to the increase in the force of gravity acting on the cylinder with water. Hence x = Δh. From the equilibrium condition for the cylinder, p2S = p0S + mg, where p2 is the gas pressure in the cylinder after its filling with water, i.e. p2 = p0 + mg/S.
Using Boyle's law, p2(h − Δh) = p1h, where p1 is the initial pressure of the gas. Finally, p1 = (p0 + mg/S)/(1 − Δh/h).
Teacher's Note: Water entering raises weight; extra buoyancy equals Δh, so gas length shrinks by Δh and Boyle's law applies.
Exam Note: Use equilibrium for final pressure, then Boyle's law at constant T.
Question 2.42. A shock wave is the region of an elevated pressure propagating in the positive direction of the x-axis at a high velocity v. At the moment of arrival of the wave, the pressure abruptly increases. This dependence is plotted in figure (i) (a step in pressure p versus x, higher on the left of the front, which moves with speed v). Determine the velocity u acquired by a wedge immediately after the shock front passes through it. The mass of the wedge is m, and its size is shown in figure (ii) (a wedge with base b along x, height a, and width c). Friction should be neglected, and the velocity acquired by the wedge should be assumed to be much lower than the velocity of the wave (u << v).
Solution. Choose the origin as shown in the figure. Then the force acting on the wedge depends only on the x-coordinate of the shock front. The horizontal component of this force is Fx = p0cx tan α = p0cxa/b = p0cavt/b, where x = vt is the wavefront coordinate at the moment t from the beginning of propagation of the wave through the wedge. The acceleration imparted to the wedge at this moment is at = Fx/m = p0cavt/(bm).
At the moment t0 when the wavefront reaches the rear face of the wedge, i.e. when b = vt0, the acceleration becomes at0 = p0ca/m. Since the acceleration depends linearly on time, for the velocity u by the moment t0 we can use the mean acceleration am = p0ca/(2m): u = amt0 = p0abc/(2mv).
When the entire wedge is in the region of elevated pressure, the resultant force on the wedge is zero. The condition u << v means that p0 << 2mv2/(abc).
Teacher's Note: Force grows linearly as the front crosses the sloping face, so use average acceleration times crossing time b/v.
Exam Note: Write F = p0(projected area) and use the mean acceleration.
Chapter 3: Electricity and Magnetism
Question 3.9. A metal sphere having a radius r1 charged to a potential φ1 is enveloped by a thin-walled conducting spherical shell of radius r2 (figure: a small sphere inside a larger concentric shell, joined by a thin wire). Determine the potential φ2 acquired by the sphere after it has been connected for a short time to the shell by a conductor.
Solution. The charge q1 of the sphere is q1 = 4πε0φ1r1. After the connection of the sphere to the envelope, the entire charge q1 will flow from the sphere to the envelope and will be distributed uniformly over its surface. Its potential φ2 (coinciding with the new potential of the sphere) will be φ2 = q1/(4πε0r2) = φ1r1/r2.
Teacher's Note: All charge moves to the outer shell; the inner sphere then sits at the shell's potential.
Exam Note: State that all charge goes to the outer shell.
Question 3.10. A very small earthed conducting sphere is at a distance a from a point charge q1 and at a distance b from a point charge q2 (a < b). At a certain instant, the sphere starts expanding so that its radius grows according to the law R = vt. Determine the time dependence I(t) of the current in the earthing conductor, assuming that the point charges and the centre of the sphere are at rest, and in due time the initial point charges get into the expanding sphere without touching it (through small holes).
Solution. We write the condition that the potential of the sphere, and hence of any point inside it (in particular its centre), is zero at time t. Single out three time intervals: (1) t < a/v, (2) a/v ≤ t < b/v, (3) t ≥ b/v.
Denoting the charge of the sphere by q(t), for the first interval: q1/a + q2/b + q(t)/(vt) = 0, whence q(t) = −v(q1/a + q2/b)t, and the current I1 = dq/dt = −v(q1/a + q2/b).
For an instant from the second interval, the fields inside and outside the sphere are independent, so (q(t) + q1)/(vt) + q2/b = 0, i.e. q(t) + q1 = −q2vt/b, and I2 = −vq2/b.
Finally, as soon as the sphere absorbs both point charges q1 and q2, the current stops flowing through the earthing conductor: I3 = 0. Thus
I(t) = −v(q1/a + q2/b) for t < a/v; I(t) = −vq2/b for a/v ≤ t < b/v; I(t) = 0 for t ≥ b/v.
Corrected: the book prints I1(t) with a trailing factor t; the current is the derivative of q(t), so it is constant (as the final piecewise answer in the book shows).
Teacher's Note: Earthed sphere keeps zero potential; as charges enter the sphere, their contribution to its centre potential changes form.
Exam Note: Split into three time intervals; current is dq/dt.
Question 3.13. Where must a current source be connected to the circuit shown in the figure in order to charge all the six capacitors having equal capacitances?
Solution. The circuit diagram is a "regular" tetrahedron whose edges contain six identical capacitors. By symmetry, irrespective of the pair of points between which the current source is connected, there always exists an uncharged capacitor in the circuit (the capacitor in the edge crossed with the edge containing the source). For example, if the source is connected between points A and B, the capacitor between points C and D will be uncharged since the potentials of points C and D are equal.
Answer: there is no such place; for any connection point at least one capacitor remains uncharged.
Teacher's Note: Opposite edges of the tetrahedron are symmetric, so the capacitor on the edge opposite the source never charges.
Exam Note: Answer: impossible; cite the symmetry (equal potentials at C and D).
Question 3.14. A parallel-plate capacitor is filled by a dielectric whose permittivity varies with the applied voltage according to the law ε = αU, where α = 1 V−1. The same (but containing no dielectric) capacitor charged to a voltage U0 = 156 V is connected in parallel to the first "nonlinear" uncharged capacitor. Determine the final voltage U across the capacitors.
Solution. The capacitance of the nonlinear capacitor is C = εC0 = αUC0, where C0 is the capacitance of the capacitor without a dielectric. The charge on the nonlinear capacitor is qn = CU = αC0U2, while the charge on the normal capacitor is q0 = C0U. It follows from charge conservation, qn + q0 = C0U0, that the required voltage is
U = (√(4αU0 + 1) − 1)/(2α) = 12 V
Check: √(4 × 156 + 1) = √625 = 25, so U = (25 − 1)/2 = 12 V.
Teacher's Note: Capacitance depends on U, so charge is αC0U2; conserve total charge and solve the quadratic.
Exam Note: Charge conservation gives the quadratic αU² + U − U0 = 0.
Question 3.15. Two small balls of mass m, bearing a charge q each, are connected by a nonconducting thread of length 2ℓ. At a certain instant, the middle of the thread starts moving at a constant velocity v perpendicular to the direction of the thread at the initial instant. Determine the minimum distance d between the balls.
Solution. Go over to the inertial frame fixed to the moving centre of the thread. Then the balls have the same velocity v at the initial instant. The energy stored initially in the system is W1 = q2/(4πε0·2ℓ) + 2mv2/2.
At the moment of closest approach, the balls are momentarily at rest in this frame, and the energy is W2 = q2/(4πε0d). Using energy conservation, d = 2ℓq2/(q2 + 8πε0mv2ℓ).
Teacher's Note: Work in the thread-centre frame, where energy conservation links initial separation 2ℓ and minimum separation d.
Exam Note: Note the balls are at rest at closest approach in that frame.
Question 3.16. Two balls of charge q1 and q2 initially have a velocity of the same magnitude and direction. After a uniform electric field has been applied during a certain time, the direction of the velocity of the first ball has changed by 60°, and the velocity magnitude is reduced by half. The direction of the velocity of the second ball changes thereby by 90°. In what proportion will the velocity of the second ball change? Determine the magnitude of the charge-to-mass ratio for the second ball if it is equal to k1 for the first ball. The electrostatic interaction between the balls should be neglected.
Solution. Let v1 and v2 be the velocities of the first and second balls after the removal of the field. By hypothesis the angle between v1 and the initial velocity v is 60°, and v1 = v/2. Therefore the change in the momentum of the first ball is Δp1 = q1EΔt = m1v sin 60°. Since v1 = v/2, Δp1 is perpendicular to v1.
Since E ∥ Δp1 and the direction of variation of the second ball's momentum is parallel to that of Δp1 (the charges have the same sign), for the velocity of the second ball: v2 = v tan 30° = v/√3, i.e. its speed falls to 1/√3 of the original.
The corresponding change in the momentum of the second ball is Δp2 = q2EΔt = m2v/cos 30°. Hence q1/q2 = (m1 sin 60°)/(m2/cos 30°) = (3/4)m1/m2, so q2/m2 = (4/3)q1/m1.
Answer: q2/m2 = (4/3)k1.
Corrected: the book ends with "= k1" (garbled); working gives the second ball's ratio as 4k1/3.
Teacher's Note: Both momentum changes lie along E; right-triangle geometry gives v2 = v tan 30° and the charge-to-mass ratio.
Exam Note: Draw velocity triangles; compare impulses q E Δt for both balls.
Question 3.17. Small identical balls with equal charges are fixed at the vertices of a regular 1977-gon with side a. At a certain instant, one of the balls is released, and a sufficiently long time interval later, the ball adjacent to the first released ball is freed. The kinetic energies of the released balls are found to differ by K at a sufficiently long distance from the polygon. Determine the charge q of each ball.
Solution. The printed solution in the source consists only of the single letter "d", which is not usable. Solution worked out here: at a large distance each ball's kinetic energy equals its electrostatic energy in the field of the balls remaining. The first ball sees the other 1976 balls: K1 = (q2/4πε0)Σj≠11/r1j. The second ball (adjacent) sees all balls except the first, which has gone away: K2 = (q2/4πε0)Σj≠1,21/r2j. By symmetry of the polygon Σj≠11/r1j = Σj≠21/r2j, so K1 − K2 = q2/(4πε0a) = K.
Corrected: q = √(4πε0aK).
Teacher's Note: Symmetry makes all sums equal except the missing first ball, so the energy difference is just the adjacent pair energy.
Exam Note: Answer q = √(4πε0aK); note symmetry argument.
JEE Mathematics: SS Krotov Solutions for S Krotov Physics Solutions 2.24 to 4.18
Chapter-wise SS Krotov Solutions: S Krotov Physics Solutions 2.24 to 4.18
Review detailed solutions for JEE Mathematics. The S Krotov Physics Solutions 2.24 to 4.18 PDF provides comprehensive answers mapped to standard SS Krotov Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Detailed Calculation Guides for JEE
Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.
Explore More Study Resources for JEE Math
In addition to these SS Krotov Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the SS Krotov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.