Official Narendra Awasthi Textbook Solutions: JEE Chemistry Chapter 09 Dilute Solution
Explore reliable textbook solutions for Chapter 09 Dilute Solution tailored for JEE learners using Narendra Awasthi methodologies. Utilizing these Chemistry answers ensures thorough preparation and strengthens foundational knowledge before final school evaluations.
Chapter-wise Solutions for Chemistry: Chapter 09 Dilute Solution
Access the complete solution PDF for JEE Chemistry below. Regular practice with these targeted textbook answers builds familiarity with standard question patterns and helps secure higher marks in final school evaluations.
Dilute Solution - Chapter 9 (Problems in Chemistry) - Levels 1 to 3, Objective and Subjective Questions
Level 1
Question 1. The vapour pressure of a given liquid will decrease if:
(a) surface area of liquid is decreased
(b) the volume of liquid in the container is decreased
(c) the volume of the vapour phase is increased
(d) the temperature is decreased
Solution. Answer: (d). Vapour pressure depends only on the nature of the liquid and the temperature, and it falls when the temperature falls. It does not depend on surface area or volume.
Teacher's Note: Vapour pressure is not a surface phenomenon; only temperature and liquid nature matter.
Exam Note: Vapour pressure depends on temperature alone.
Question 2. The normal boiling point of water is 373 K. Vapour pressure of water at temperature T is 19 mm Hg. If enthalpy of vaporisation is 40.67 kJ/mol, then temperature T would be (Use: log 2 = 0.3, R = 8.3 J K-1 mol-1):
(a) 250 K
(b) 291.4 K
(c) 230 K
(d) 290 K
Solution. Answer: (b). Clausius-Clapeyron: log(P2/P1) = (ΔHvap/2.303R)·(T2−T1)/(T1T2). With P2 = 760 mm Hg at T2 = 373 K and P1 = 19 mm Hg: log(760/19) = (40670/(2.303×8.3))·(373−T1)/(T1×373). Solving, T1 = 291.4 K.
Teacher's Note: Use the normal boiling point (760 mm Hg at 373 K) as the second data point.
Exam Note: Choose correct pair (P, T) before substituting in Clausius-Clapeyron.
Question 3. A sample of liquid H2O of mass 18.0 g is injected into an evacuated 7.6 L flask maintained at 27.0°C. If vapour pressure of H2O at 27°C is 24.63 mm Hg, what weight percentage of the water will be vapourised when the system comes to equilibrium? Assume water vapours behave as an ideal gas. The volume occupied by the liquid water is negligible compared to the volume of the container:
(a) 1%
(b) 10%
(c) 18%
(d) 20%
Solution. Answer: (a). Moles of water in vapour = PV/RT = (24.63/760)×7.6/(0.0821×300) = 0.01 mol = 0.18 g. % vaporised = (0.18/18)×100 = 1%.
Teacher's Note: Equilibrium vapour pressure fixes the vapour moles via PV = nRT; convert mm Hg to atm.
Exam Note: Convert mm Hg to atm before using R = 0.0821.
Question 4. Raoult's law is obeyed by each constituent of a binary liquid solution when:
(a) the forces of attractions between like molecules are greater than those between unlike molecules
(b) the forces of attractions between like molecules are smaller than those between unlike molecules
(c) the forces of attractions between like molecules are identical with those between unlike molecules
(d) the volume occupied by unlike molecules are different
Solution. Answer: (c). An ideal solution obeys Raoult's law when A-A, B-B and A-B interactions are of equal strength, so ΔHmix = 0 and ΔVmix = 0.
Teacher's Note: Ideality means A-B interactions match A-A and B-B interactions.
Exam Note: Ideal solution: ΔH and ΔV of mixing are zero.
Question 5. For a binary ideal liquid solution, the total pressure of the solution is given as:
(a) Ptotal = PA° + (PA° − PB°)XB
(b) Ptotal = PB° + (PA° − PB°)XA
(c) Ptotal = PB° + (PB° − PA°)XA
(d) Ptotal = PB° + (PB° − PA°)XB
Solution. Answer: (b). P = PA°XA + PB°XB and XB = 1 − XA, so P = PB° + (PA° − PB°)XA.
Teacher's Note: Substitute XB = 1 − XA in Dalton-Raoult sum; P is linear in XA.
Exam Note: Eliminate XB; check options at XA = 0 and 1.
Question 6. For an ideal binary liquid solution with PA° > PB°, which relation between XA (mole fraction of A in liquid phase) and YA (mole fraction of A in vapour phase) is correct?
(a) YA < YB
(b) XA > XB
(c) YA/YB > XA/XB
(d) YA/YB < XA/XB
Solution. Answer: (c). YA/YB = (PA°/PB°)(XA/XB). Since PA° > PB°, YA/YB > XA/XB: the vapour is richer in the more volatile component.
Teacher's Note: Vapour is richer in the more volatile component; ratio YA/YB = (PA°/PB°)(XA/XB).
Exam Note: Statements (a),(b) need not hold; only the ratio form is general.
Question 7. An ideal solution is formed by mixing two volatile liquids A and B. XA and XB are the mole fractions of A and B respectively in the solution and YA and YB are the mole fractions of A and B respectively in the vapour phase. A plot of 1/YA along y-axis against 1/XA along x-axis gives a straight line. What is the slope of the straight line?
(a) PB°/PA°
(b) PA°/PB°
(c) PB° − PA°
(d) PA° − PB°
Solution. Answer: (a). YA = PA°XA/[PB° + (PA° − PB°)XA], so 1/YA = (PB°/PA°)(1/XA) + (PA° − PB°)/PA°. Slope = PB°/PA°, intercept = (PA° − PB°)/PA°.
Teacher's Note: Invert YA expression to get a linear form in 1/XA.
Exam Note: Write y = mx + c form; slope read directly.
Question 8. For a dilute solution, Raoult's law states that:
(a) the lowering of vapour pressure is equal to the mole fraction of solute
(b) the relative lowering of vapour pressure is equal to the mole fraction of solute
(c) the relative lowering of vapour pressure is proportional to the amount of solute in solution
(d) the vapour pressure of the solution is equal to the mole fraction of solvent
Solution. Answer: (b). (P° − P)/P° = Xsolute.
Teacher's Note: It is the relative (not absolute) lowering that equals solute mole fraction.
Exam Note: Quote (P° − P)/P° = Xsolute exactly.
Question 9. The solubility of a specific non-volatile salt is 4 g in 100 g of water at 25°C. If 2.0 g, 4.0 g and 6.0 g of the salt added to 100 g of water at 25°C, in system X, Y and Z. The vapour pressure would be in the order:
(a) X < Y < Z
(b) X > Y > Z
(c) Z > X = Y
(d) X > Y = Z
Solution. Answer: (d). In X (2 g) the solution is unsaturated, so its vapour pressure is higher. Y (4 g) is exactly saturated and Z (6 g) is saturated with 2 g undissolved solid, so the dissolved amount is 4 g in both and their vapour pressures are equal. Hence X > Y = Z.
Teacher's Note: Undissolved solid does not affect vapour pressure; only dissolved amount counts.
Exam Note: Saturation caps the dissolved solute, so Y and Z are equal.
Question 10. The boiling point of C6H6, CH3OH, C6H5NH2 and C6H5NO2 are 80°C, 65°C, 184°C and 212°C respectively. Which will show highest vapour pressure at room temperature:
(a) C6H6
(b) CH3OH
(c) C6H5NH2
(d) C6H5NO2
Solution. Answer: (b). The liquid with the lowest boiling point is the most volatile and has the highest vapour pressure at a given temperature: CH3OH (65°C).
Teacher's Note: Lower boiling point means weaker net attraction, hence higher vapour pressure.
Exam Note: Lowest boiling point gives highest vapour pressure.
Question 11. 6.0 g of urea (molecular weight = 60) was dissolved in 9.9 moles of water. If the vapour pressure of pure water is P°, the vapour pressure of solution is:
(a) 0.10 P°
(b) 1.10 P°
(c) 0.90 P°
(d) 0.99 P°
Solution. Answer: (d). nurea = 6/60 = 0.1 mol. (P° − P)/P° = 0.1/(0.1 + 9.9) = 0.01, so P = 0.99 P°.
Teacher's Note: Relative lowering equals solute mole fraction 0.1/10.
Exam Note: Compute mole fraction first, then P = P°(1 − X).
Question 12. An ideal solution was found to have a vapour pressure of 80 torr when the mole fraction of a non-volatile solute was 0.2. What would be the vapour pressure of the pure solvent at the same temperature?
(a) 64 torr
(b) 80 torr
(c) 100 torr
(d) 400 torr
Solution. Answer: (c). P = P°Xsolvent → 80 = P° × 0.8 → P° = 100 torr.
Teacher's Note: Solvent mole fraction is 1 − 0.2 = 0.8, not 0.2.
Exam Note: Use solvent mole fraction in P = P°X.
Question 13. The vapour pressure of an aqueous solution of sucrose at 373 K is found to be 750 mm Hg. The molality of the solution at the same temperature will be:
(a) 0.26
(b) 0.73
(c) 0.74
(d) 0.039
Solution. Answer: (c). P° = 760 mm Hg at 373 K. m = ((P° − P)/P)×(1000/Msolvent) = (10/750)×(1000/18) = 0.74.
Teacher's Note: At 373 K pure water has 760 mm Hg; use (P° − P)/P form.
Exam Note: Remember P° of water at its normal boiling point is 760.
Question 14. Estimate the lowering of vapour pressure due to the solute (glucose) in a 1.0 M aqueous solution at 100°C:
(a) 10 torr
(b) 18 torr
(c) 13.45 torr
(d) 24 torr
Solution. Answer: (c). P° = 760 torr. Taking 1 M ≈ 1 m: (P° − P)/P = m×18/1000 = 0.018, so P = 746.5 torr and ΔP = 13.45 torr.
Teacher's Note: Treat 1 M as 1 m for a dilute solution; P° of water at 100°C is 760 torr.
Exam Note: Use (P° − P)/P form, not Xsolute, for the exact value.
Question 15. Calculate the weight of non-volatile solute having molecular weight 40, which should be dissolved in 57 gm octane to reduce its vapour pressure to 80%:
(a) 47.2 g
(b) 5 g
(c) 106.2 g
(d) None of these
Solution. Answer: (b). P = 0.8P°, so (P° − P)/P = 0.2/0.8 = w×114/(40×57). Hence w = 5 g (M of octane = 114).
Teacher's Note: Reduced to 80% means P = 0.8P°, so (P° − P)/P = 0.25.
Exam Note: Use molar mass of octane 114 g/mol.
Question 16. Equal weight of a solute are dissolved in equal weight of two solvents A and B and formed very dilute solution. The relative lowering of vapour pressure for the solution B has twice the relative lowering of vapour pressure for the solution A. If MA and MB are the molecular weights of solvents A and B respectively, then:
(a) MA = MB
(b) MB = 2×MA
(c) MA = 4MB
(d) MA = 2MB
Solution. Answer: (b). For a dilute solution (P° − P)/P° ≈ n/N, which for equal masses of solute and solvent is proportional to the solvent molar mass. So 2×(n/NA) = n/NB, giving MB = 2MA.
Teacher's Note: With same solute and solvent masses, relative lowering is proportional to solvent molar mass.
Exam Note: Relative lowering ∝ solvent molar mass here.
Question 17. An ideal solution has two components A and B. A is more volatile than B, i.e., PA° > PB° and also PA° > Ptotal. If XA and YA are mole fractions of component A in liquid and vapour phases, then:
(a) XA = YA
(b) XA > YA
(c) XA < YA
(d) Data insufficient
Solution. Answer: (c). YA = PA°XA/Ptotal, so YA/XA = PA°/Ptotal > 1. Hence YA > XA.
Teacher's Note: YA/XA = PA°/Ptotal exceeds 1 for the volatile component.
Exam Note: Use YA = PA°XA/P.
Question 18. At 25°C, the vapour pressure of pure liquid A (mol. wt. = 40) is 100 torr, while that of pure liquid B is 40 torr, (mol. wt. = 80). The vapour pressure at 25°C of a solution containing 20 g each of A and B is:
(a) 80 torr
(b) 59.8 torr
(c) 68 torr
(d) 48 torr
Solution. Answer: (a). nA = 20/40 = 0.5, nB = 20/80 = 0.25. XA = 0.667, XB = 0.333. P = 100×0.667 + 40×0.333 = 80 torr.
Teacher's Note: Convert grams to moles before taking mole fractions.
Exam Note: Mole fractions, not mass fractions, go into Raoult's law.
Question 19. Two liquids A and B from ideal solutions. At 300 K, the vapour pressure of solution containing 1 mole of A and 3 mole of B is 550 mm Hg. At the same temperature, if one more mole of B is added to this solution, the vapour pressure of the solution increases by 10 mm Hg. Determine the vapour pressure of A and B in their pure states (in mm Hg):
(a) 400, 600
(b) 500, 500
(c) 600, 400
(d) None of these
Solution. Answer: (a). First solution: ¼PA° + ¾PB° = 550. After adding 1 mol B (1 mol A, 4 mol B): ⅕PA° + ⅘PB° = 560. Solving, PA° = 400 mm Hg and PB° = 600 mm Hg.
Teacher's Note: Two compositions give two linear equations in PA° and PB°.
Exam Note: Set up both mole-fraction equations; solve simultaneously.
Question 20. Two liquids A and B have vapour pressure in the ratio PA° : PB° = 1 : 3 at a certain temperature. Assume A and B form an ideal solution and the ratio of mole fractions of A to B in the vapour phase is 4 : 3. Then the mole fraction of B in the solution at the same temperature is:
(a) 1/5
(b) 2/3
(c) 4/5
(d) 1/4
Solution. Answer: (a). YA/YB = (PA°/PB°)(XA/XB): 4/3 = (1/3)(XA/XB), so XA/XB = 4, XA = 4/5 and XB = 1/5.
Teacher's Note: Use the vapour-to-liquid ratio relation to get XA/XB = 4.
Exam Note: Ask for XB, not XA.
Question 21. Two liquids A and B have PA° and PB° in the ratio of 1 : 3 and the ratio of number of moles of A and B in liquid phase are 1 : 3 then mole fraction of 'A' in vapour phase in equilibrium with the solution is equal to:
(a) 0.1
(b) 0.2
(c) 0.5
(d) 1.0
Solution. Answer: (a). YA/YB = (1/3)(1/3) = 1/9, so YA = 1/(1+9) = 0.1.
Teacher's Note: Ratios multiply: (1/3)×(1/3) = 1/9 gives YA = 0.1.
Exam Note: Convert ratio 1:9 into a fraction 1/10.
Question 22. Based on the given diagram, which of the following statements regarding the homogenous solutions of two volatile liquids are correct?
(Figure: vapour pressure against mole fraction between XA = 1 and XB = 1. Straight line AD is the vapour pressure PB° rising from A to B; line CB falls from PA° at A to zero at B; CD is the total vapour pressure line joining the pure-component values; E is a composition on the axis with F, G and H on the lines above it.)
(1) Plots AD and BC show that Raoult's law is obeyed for the solution in which B is a solvent and A is the solute and as well as for that in which A is solvent and B is solute.
(2) Plot CD shows that Dalton's law of partial pressures is obeyed by the binary solution of components A and B.
(3) EF + EG = EH; and AC and BD correspond to the vapour pressures of the pure solvents A and B respectively.
(a) Only 1 (b) 2 and 3 (c) 1 and 3 (d) All
Solution. Answer: (d). Per the printed key, all three statements are correct: the partial-pressure lines obey Raoult's law, the total pressure line CD is the sum of the partial pressures (Dalton's law, EF + EG = EH), and AC and BD are the vapour pressures of pure A and B.
Teacher's Note: Partial pressures add to the total line; end intercepts are pure-liquid vapour pressures.
Exam Note: Dalton: total = sum of partials; read figure carefully.
Question 23. Which represents correct difference when non-volatile solute is present in an ideal solution?
(Figure: three energy-level diagrams. (I) Entropy: solution has higher entropy than solvent and the vapour is higher still, with (ΔS)solution to vapour smaller than (ΔS)solvent to vapour. (II) Enthalpy: ΔH of vaporisation of solution equals ΔH of vaporisation of solvent. (III) Boiling point: boiling point of solution is above that of the solvent.)
(a) I, II, III
(b) I, III
(c) II, III
(d) I, II
Solution. Answer: (a). All three diagrams are correct. The entropy change on vaporisation is smaller for the solution than for the pure solvent (the solution is already more disordered), ΔHvap is the same because intermolecular forces are similar, and the boiling point of the solution is higher.
Teacher's Note: Solute raises liquid entropy, so vaporisation entropy gain is smaller; enthalpy unchanged.
Exam Note: Know ΔSvap of solution is less than that of solvent.
Question 24. Select correct statement:
(a) Solution has more molecular randomness than a pure solvent has, the entropy change between solution and solid is larger than the entropy change between pure solvent and solid
(b) Heat of fusion of solution and solvent are similar since similar forces of intermolecular forces are involved
(c) Sugar containing solution freezes at a lower temperature than pure water
(d) All are correct statements
Solution. Answer: (d). All three statements are correct: the solution is more random, so freezing it involves a larger entropy change; the heats of fusion are similar; and freezing point depression lowers the freezing temperature of the sugar solution.
Teacher's Note: Freezing point depression arises from higher entropy of solution compared with solvent.
Exam Note: Link entropy argument to freezing point depression.
Question 25. Select correct statement?
(a) Heats of vaporisation for a pure solvent and for a solution are similar because similar intermolecular forces between solvent molecules must be overcome in both cases
(b) Entropy change between solution and vapour is smaller than the entropy change between pure solvent and vapour
(c) Boiling point of the solution is larger than that of the pure solvent
(d) All are correct statements
Solution. Answer: (d). All three statements are correct (see Question 23).
Teacher's Note: Solute increases boiling point; vaporisation enthalpy stays similar.
Exam Note: All three entropy, enthalpy and b.p. statements hold.
Question 26. The vapour pressure curves of the same solute in the same solvent are shown. The curves are parallel to each other and do not intersect. The concentrations of solutions are in order of:
(Figure: vapour pressure (torr) against temperature with a 1 atm line; the pure solvent curve is on the left, and curves I, II, III lie to its right, meeting the 1 atm line at boiling points that increase in the order I, II, III.)
(a) I < II < III
(b) I = II = III
(c) I > II > III
(d) I > III > II
Solution. Answer: (a). Elevation in boiling point is proportional to the concentration of the solution. Curve III has the highest boiling point, so concentration increases in the order I < II < III.
Teacher's Note: Boiling point elevation measured at 1 atm is proportional to concentration.
Exam Note: Higher boiling point means more concentrated solution.
Question 27. Boiling point composition diagram of the liquid-vapour equilibrium for A and B is shown figure. If a binary liquid mixture of A and B is distilled fractionally, which of the following would be correct observation?
(Figure: temperature against composition from XA = 1 to XB = 1; a lens-shaped region between the vapour curve (upper) and liquid curve (lower), with no azeotropic maximum or minimum.)
(a) Composition of the still (residue) will approach pure liquid B
(b) Composition of the distillate will approach pure A
(c) Composition of distillate and residue will approach pure A and B respectively
(d) Neither of the components can be obtained in pure state
Solution. Answer: (c). The diagram has no azeotrope, so fractional distillation separates the mixture completely: the more volatile component A collects as distillate and B remains as residue.
Teacher's Note: No azeotrope on the diagram, so complete separation is possible.
Exam Note: Volatile component distils first; the less volatile stays as residue.
Question 28. The boiling point of an azeotropic mixture of water-ethanol is less than that of both water and ethanol. Then:
(a) the mixture will show negative deviation from Raoult's law
(b) the mixture will show positive deviation from Raoult's law
(c) the mixture will show no deviation from Raoult's law
(d) this mixture cannot be considered as true solution
Solution. Answer: (b). A minimum-boiling azeotrope forms when the solution shows positive deviation from Raoult's law.
Teacher's Note: Minimum-boiling azeotrope goes with positive deviation; maximum-boiling with negative.
Exam Note: Minimum b.p. azeotrope means positive deviation.
Question 29. Formation of a solution from two components can be considered as: (i) Pure solvent → separated solvent molecules, ΔH1; (ii) Pure solute → separated solute molecules, ΔH2; (iii) separated solvent and solute molecules → solution, ΔH3. Solution so formed will be ideal if:
(a) ΔHsoln = ΔH1 + ΔH2 + ΔH3
(b) ΔHsoln = ΔH1 + ΔH2 − ΔH3
(c) ΔHsoln = ΔH1 − ΔH2 − ΔH3
(d) ΔHsoln = ΔH1 − ΔH2 + ΔH3
Solution. Answer: (a) (from key). The total enthalpy of solution is the sum of the three steps, ΔHsoln = ΔH1 + ΔH2 + ΔH3, with ΔH3 negative; the solution is ideal when this total is zero (ΔH1 + ΔH2 = −ΔH3).
Teacher's Note: Hess-type sum of the three steps; ideality means the sum is zero.
Exam Note: State the three-step sum and set it to zero.
Question 30. Total vapour pressure of mixture of 1 mol X (PX° = 150 torr) and 2 mol Y (PY° = 300 torr) is 240 torr. In this case:
(a) There is a negative deviation from Raoult's law
(b) There is a positive deviation from Raoult's law
(c) There is no deviation from Raoult's law
(d) Can not be decided
Solution. Answer: (a). Ideal total pressure = (1/3)(150) + (2/3)(300) = 250 torr. The observed 240 torr is lower, so there is negative deviation.
Teacher's Note: Compare observed pressure with the ideal sum: lower means negative deviation.
Exam Note: Calculate the ideal value first, then compare.
Question 31. In a mixture of A and B, components show positive deviation when:
(a) A-B interaction is stronger than A-A and B-B interaction
(b) A-B interaction is weaker than A-A and B-B interaction
(c) ΔV mix < 0, ΔS mix > 0
(d) ΔV mix = 0, ΔS mix > 0
Solution. Answer: (b). Weaker A-B interactions let molecules escape more easily, so vapour pressure exceeds the Raoult value; ΔHmix and ΔVmix are positive.
Teacher's Note: Weaker unlike attractions raise escaping tendency, giving positive deviation.
Exam Note: Positive deviation: ΔHmix and ΔVmix positive.
Question 32. A liquid mixture having composition corresponding to point Z in the figure shown is subjected to distillation at constant pressure. Which of the following statement is correct about the process?
(Figure: boiling point against composition from pure A (TA) to pure B (TB); the boiling point curve rises to a maximum at the central point Z, where the liquid and vapour curves touch.)
(a) The composition of distillate differs from the mixture
(b) The boiling point goes on changing
(c) The mixture has highest vapour pressure than for any other composition
(d) Composition of an azeotrope alters on changing the external pressure
Solution. Answer: (d). Point Z is a maximum-boiling azeotrope: distillate and residue have the same composition and the boiling point stays constant, so (a) and (b) are false. The mixture has the lowest (not highest) vapour pressure, so (c) is false. The azeotropic composition changes with external pressure.
Teacher's Note: At the azeotrope, liquid and vapour compositions are equal; composition shifts with pressure.
Exam Note: Azeotropic composition depends on external pressure.
Question 33. Which will form maximum boiling azeotrope?
(a) C6H6 + C6H5CH3 solution
(b) HNO3 + H2O solution
(c) C2H5OH + H2O solution
(d) n-hexane and n-heptane
Solution. Answer: (b). Maximum-boiling azeotropes arise from negative deviation (strong hydrogen bonding or acid-water interaction), as in HNO3 + H2O.
Teacher's Note: Negative deviation systems (acid + water) give maximum-boiling azeotropes.
Exam Note: Benzene-toluene and hexane-heptane are ideal pairs.
Question 34. Total vapour pressure of mixture of 1 mole of volatile component A (PA° = 100 mm Hg) and 3 mole of volatile component B (PB° = 80 mm Hg) is 90 mm Hg. For such case:
(a) there is positive deviation from Raoult's law
(b) boiling point has been lowered
(c) force of attraction between A and B is smaller than that between A and A or between B and B
(d) all the above statements are correct
Solution. Answer: (d). Ideal pressure = 100×¼ + 80×¾ = 85 mm Hg; the actual 90 mm Hg is greater, so there is positive deviation. That means weaker A-B attraction and a lower boiling point.
Teacher's Note: Actual pressure exceeds ideal 85: positive deviation, weaker A-B forces, lower b.p.
Exam Note: Compute ideal pressure, compare, then deduce the rest.
Question 35. The azeotropic mixture of water (B.P. = 100°C) and HCl (B.P. = 86°C) boils at about 120°C. During fractional distillation of this mixture it is possible to obtain:
(a) pure HCl
(b) pure H2O
(c) pure H2O as well as pure HCl
(d) neither H2O nor HCl
Solution. Answer: (d). An azeotropic mixture boils at constant temperature with the same composition in vapour and liquid, so it cannot be separated by fractional distillation.
Teacher's Note: An azeotrope distils unchanged, so no separation by distillation.
Exam Note: Azeotrope is a constant-boiling mixture.
Question 36. Azeotropic mixture of water and HCl boils at 381.5 K. By distilling the mixture it is possible to obtain:
(a) Pure HCl only
(b) Pure water only
(c) Neither HCl nor water
(d) Both water and HCl in pure state
Solution. Answer: (c). The azeotrope distils at constant composition, so neither pure HCl nor pure water can be obtained.
Teacher's Note: Constant boiling means no change in composition on distillation.
Exam Note: Same reasoning as question 35.
Question 37. An azeotropic mixture of two liquids has a boiling point higher than either of them when it:
(a) shows positive deviation from Raoult's law
(b) shows negative deviation from Raoult's law
(c) shows ideal behaviour
(d) is saturated
Solution. Answer: (b). A maximum-boiling azeotrope forms when the solution shows large negative deviation from Raoult's law.
Teacher's Note: Higher boiling point means lower vapour pressure: negative deviation.
Exam Note: Maximum b.p. azeotrope implies negative deviation.
Question 38. If two liquids A (PA° = 100 torr) and B (PB° = 200 torr) are completely immiscible with each other (each one will behave independently of the other) are present in a closed vessel. The total vapour pressure of the system will be:
(a) less than 100 torr
(b) greater than 200 torr
(c) between 100 to 200 torr
(d) 300 torr
Solution. Answer: (d). For immiscible liquids each exerts its own pure vapour pressure, so P = PA° + PB° = 100 + 200 = 300 torr.
Teacher's Note: Immiscible liquids: partial pressures are the pure values and simply add.
Exam Note: Do not use mole fractions for immiscible liquids.
Question 39. When a liquid that is immiscible with water was steam distilled at 95.2°C at a total pressure of 748 torr, the distillate contained 1.25 g of the liquid per gram of water. The vapour pressure of water is 648 torr at 95.2°C, what is the molar mass of liquid?
(a) 7.975 g/mol
(b) 166 g/mol
(c) 145.8 g/mol
(d) None of these
Solution. Answer: (c). Pliquid = 748 − 648 = 100 torr. wA/wB = PA°MA/(PB°MB): 1.25/1 = 100×MA/(648×18), so MA = 145.8 g/mol.
Teacher's Note: Steam distillation: mass ratio equals (P×M) ratio; liquid pressure = total − water.
Exam Note: Subtract water pressure from total to get the liquid's.
Question 40. Water and chlorobenzene are immiscible liquids. Their mixture boils at 89°C under a reduced pressure of 7.7 × 104 Pa. The vapour pressure of pure water at 89°C is 7 × 104 Pa. Weight per cent of chlorobenzene in the distillate is:
(a) 50
(b) 60
(c) 78.3
(d) 38.46
Solution. Answer: (d). Pchlorobenzene = 7.7×104 − 7×104 = 0.7×104 Pa. wA/wB = (0.7×112.5)/(7×18) = 0.625. Weight % = 0.625/1.625 × 100 = 38.46.
Teacher's Note: Mass ratio = (P×M) ratio; convert to percentage of total distillate mass.
Exam Note: Use M = 112.5 for chlorobenzene and 18 for water.
Question 41. Which of the following is not a colligative property?
(a) Vapour pressure
(b) Depression in f.pt.
(c) Elevation in b.pt.
(d) Osmotic pressure
Solution. Answer: (a). The colligative properties are relative lowering of vapour pressure, elevation of boiling point, depression of freezing point and osmotic pressure. Vapour pressure itself is not.
Teacher's Note: Relative lowering of vapour pressure is colligative; vapour pressure itself is not.
Exam Note: Distinguish vapour pressure from its relative lowering.
Question 42. The degree of dissociation of an electrolyte is α and its van't Hoff factor is i. The number of ions obtained by complete dissociation of 1 molecule of the electrolyte is:
(a) (i + α − 1)/α
(b) i − α − 1
(c) (i − 1)/α
(d) (i + 1 + α)/(1 − α)
Solution. Answer: (a). i = 1 + (n − 1)α, so n = 1 + (i − 1)/α = (i + α − 1)/α.
Teacher's Note: Rearrange i = 1 + (n − 1)α for n.
Exam Note: Use i = 1 + (n − 1)α.
Question 43. One mole of a solute A is dissolved in a given volume of a solvent. The association of the solute take place as follows: nA ⇌ An. If α is the degree of association of A, the van't Hoff factor i is expressed as:
(a) i = 1 − α
(b) i = 1 + α/n
(c) i = (1 − α + α/n)/1
(d) i = 1
Solution. Answer: (c). Initially 1 mol A; at equilibrium moles of A = 1 − α and of An = α/n. Total = 1 − α + α/n, so i = 1 − α + α/n.
Teacher's Note: Count particles: (1 − α) of A plus α/n of An.
Exam Note: Association lowers the particle count, so i < 1.
Question 44. The van't Hoff factor i for an electrolyte which undergoes dissociation and association in solvent are respectively:
(a) greater than one and less than one
(b) less than one and greater than one
(c) less than one and less than one
(d) greater than one and greater than one
Solution. Answer: (a). Dissociation increases the number of particles, so i > 1; association decreases it, so i < 1.
Teacher's Note: Dissociation raises particle number (i > 1); association lowers it (i < 1).
Exam Note: Link i to change in number of particles.
Question 45. Which solution has the highest vapour pressure?
(a) 0.02 M NaCl at 50°C
(b) 0.03 M sucrose at 15°C
(c) 0.005 M CaCl2 at 50°C
(d) 0.005 M CaCl2 at 25°C
Solution. Answer: (c). Vapour pressure rises with temperature and falls with solute particles. Option (c) combines the highest temperature (50°C) with the fewest particles (0.015 M against 0.04 M in (a)).
Teacher's Note: Highest temperature plus lowest particle concentration gives highest vapour pressure.
Exam Note: Compare at 50°C: 0.015 versus 0.04 mol particles.
Question 46. An aqueous solution is 1.00 molal in KI. Which change will cause the vapour pressure of the solution to increase?
(a) addition of water
(b) addition of NaCl
(c) addition of Na2SO4
(d) Addition of 1.0 molal KI
Solution. Answer: (a). Adding water dilutes the solution and reduces the mole fraction of solute, so vapour pressure rises. Adding any solute lowers it.
Teacher's Note: Dilution lowers solute mole fraction, raising vapour pressure.
Exam Note: Added solute can only lower vapour pressure.
Question 47. Four solutions of K2SO4 with the concentrations 0.1 m, 0.01 m, 0.001 m and 0.0001 m are available. The maximum value of colligative property corresponds to:
(a) 0.0001 m solution
(b) 0.001 m solution
(c) 0.01 m solution
(d) 0.1 m solution
Solution. Answer: (d). Colligative properties increase with the number of particles; the 0.1 m solution has the most (although i is slightly lower at high concentration, particle count dominates).
Teacher's Note: Colligative property scales with particle concentration.
Exam Note: Highest concentration gives the largest colligative property.
Question 48. Moles of Na2SO4 to be dissolved in 12 mole water to lower its vapour pressure by 10 mm Hg at a temperature at which vapour pressure of pure water is 50 mm is:
(a) 1.5 mole
(b) 2 mole
(c) 1 mole
(d) 3 mole
Solution. Answer: (c). Na2SO4 gives 3 particles (i = 3). ΔP/P° = 10/50 = 0.2 = 3n/(3n + 12), so 3n = 0.6n + 2.4 and n = 1 mol.
Teacher's Note: Complete dissociation: effective solute moles are 3n.
Exam Note: Use i = 3 for Na2SO4.
Question 49. A very diluted saturated solution of a sparingly soluble salt X3Y4 has a vapour pressure of 20 mm Hg at temperature T, while pure water exerts a pressure of 20.0126 mm Hg at the same temperature. Calculate molarity (m) of the solution at temperature T:
(a) 6.3 × 10-4
(b) 3.5 × 10-2
(c) 5 × 10-3
(d) None of these
Solution. Answer: (c). X3Y4 gives 3 + 4 = 7 ions. (P° − P)/P = i·m·18/1000: 7m = (20.0126 − 20)×1000/(20×18) = 0.035, so m = 5×10-3.
Teacher's Note: Salt of formula X3Y4 gives 7 ions, so i = 7.
Exam Note: Count ions from the formula before computing.
Question 50. When 1 mole of a solute is dissolved in 1 kg of H2O, boiling point of solution was found to be 100.5°C. Kb for H2O is:
(a) 0.5
(b) 100
(c) 100.5
(d) 95.5
Solution. Answer: (a). ΔTb = 100.5 − 100 = 0.5°C = Kb×1 molal, so Kb = 0.5 K kg mol-1.
Teacher's Note: Molality is 1, so Kb equals the elevation 0.5.
Exam Note: Subtract 100°C to get ΔTb.
Question 51. Chloroform, CHCl3, boils at 61.7°C. If the Kb for chloroform is 3.63°C/molal; the boiling point of a solution of 15.0 kg of CHCl3 and 0.616 kg of acenaphthylene, C12H10?
(a) 61.9
(b) 62.0
(c) 52.2
(d) 62.67
Solution. Answer: (d). Moles of C12H10 = 0.616 kg/154 = 0.004 kmol (4 mol); m = 4/15 = 0.2667. ΔTb = 3.63×0.2667 = 0.968°C, so Tb = 61.7 + 0.968 = 62.67°C.
Teacher's Note: Masses in kg give kmol; molality = 4 mol/15 kg.
Exam Note: Add ΔTb to the pure solvent boiling point.
Question 52. A compound has the empirical formula C10H8Fe. A solution of 0.26 g of the compound in 11.2 g of benzene (C6H6) boils at 80.26°C. The boiling point of benzene is 80.10°C; the Kb is 2.53°C/molal. What is the molecular formula of the compound?
(a) C30H24Fe3
(b) C10H8Fe
(c) C5H4Fe
(d) C20H16Fe2
Solution. Answer: (d). ΔTb = 0.16 = 2.53×(0.26/M)×(1000/11.2), so M ≈ 367. Empirical mass = 184, so the molecular formula is twice: C20H16Fe2 (calculation gives M ≈ 367, matching 368).
Teacher's Note: Find M from ΔTb, then divide by empirical formula mass (184).
Exam Note: Molecular mass ÷ empirical mass gives the multiplier 2.
Question 53. A solution of 0.640 g of azulene in 100.0 g of benzene boils at 80.23°C. The boiling point of benzene is 80.10°C; the Kb is 2.53°C/molal. What is the molecular weight of azulene?
(a) 108
(b) 99
(c) 125
(d) 134
Solution. Answer: (c). ΔTb = 0.13 = 2.53×(0.640/M)×(1000/100), so M = 2.53×6.4/0.13 ≈ 125 (calculated 124.5).
Teacher's Note: Molecular weight from ΔTb = Kb·w·1000/(M·W).
Exam Note: Use W = 100 g in the 1000/W factor.
Question 54. One molal solution of a carboxylic acid in benzene shows the elevation of boiling point of 1.518 K. The degree of association for dimerization of the acid in benzene is (Kb for benzene = 2.53 K kg mol-1):
(a) 60%
(b) 70%
(c) 75%
(d) 80%
Solution. Answer: (d). Normal ΔTb = 2.53×1 = 2.53 K. i = 1.518/2.53 = 0.6. For dimerisation i = 1 − α/2, so α = 0.8 = 80%.
Teacher's Note: i is observed over normal ΔTb; dimer gives i = 1 − α/2.
Exam Note: Use n = 2 in i = 1 − α(1 − 1/n).
Question 55. The boiling point elevation constant for toluene is 3.32 K kg mol-1. The normal boiling point of toluene is 110.7°C. The enthalpy of vaporisation of toluene would be nearly:
(a) 17.0 kJ mol-1
(b) 34.0 kJ mol-1
(c) 51.0 kJ mol-1
(d) 68.0 kJ mol-1
Solution. Answer: (b). ΔHvap = M·R·Tb²/(1000·Kb) = 92×8.314×(383.7)²/(1000×3.32) = 33.91 kJ/mol ≈ 34 kJ/mol.
Teacher's Note: Use Kb = MRTb²/(1000ΔHvap) with T in kelvin.
Exam Note: Convert 110.7°C to 383.7 K first.
Question 56. Which one of the following aqueous solutions will exhibit highest boiling point:
(a) 0.015 M urea
(b) 0.01 M KNO3
(c) 0.10 M Na2SO4
(d) 0.015 M glucose
Solution. Answer: (c). Particle concentrations: urea 0.015, KNO3 0.02, Na2SO4 0.30, glucose 0.015. The largest is Na2SO4, so it has the highest boiling point.
Teacher's Note: Highest total particle concentration gives highest boiling point.
Exam Note: Multiply molarity by i for each solute.
Question 57. Calculate the percentage degree of dissociation of an electrolyte XY2 (Normal molar mass = 164) in water if the observed molar mass by measuring elevation in boiling point is 65.6:
(a) 75%
(b) 25%
(c) 65%
(d) None of these
Solution. Answer: (a). i = 164/65.6 = 2.5. For XY2 (n = 3): i = 1 + 2α, so α = 0.75 = 75%.
Teacher's Note: i = normal/observed molar mass; n = 3 for XY2.
Exam Note: Use i = 1 + (n − 1)α with n = 3.
Question 58. If the elevation in boiling point of a solution of non-volatile, non-electrolytic and non-associating solute in solvent (Kb = x K kg mol-1) is y K, then the depression in freezing point of solution of same concentration would be (Kf of the solvent = z K kg mol-1):
(a) 2xz/y
(b) yz/x
(c) xz/y
(d) yz/2x
Solution. Answer: (b). m = y/x from ΔTb = Kbm. Then ΔTf = Kfm = z·y/x = yz/x.
Teacher's Note: Same molality links both properties: m = y/x.
Exam Note: Find m first, then multiply by Kf.
Question 59. When a solution containing non-volatile solute freezes, which equilibrium would exist?
(a) solid solvent ⇌ liquid solvent
(b) solid solute ⇌ liquid solution
(c) solid solute ⇌ liquid solvent
(d) solid solvent ⇌ liquid solution
Solution. Answer: (d). Freezing of a dilute solution means pure solid solvent separates and is in equilibrium with the liquid solution.
Teacher's Note: Only pure solvent freezes out, in equilibrium with the solution.
Exam Note: Solid solvent is in equilibrium with liquid solution.
Question 60. Bromoform has a normal freezing point of 7.734°C/m and it's Kf = 14.4°C/m. A solution of 2.60 g of an unknown in 100 g of bromoform freezes at 5.43°C. What is the molecular weight of the unknown?
(a) 16.25
(b) 162.5
(c) 100
(d) none of these
Solution. Answer: (b). The normal freezing point of bromoform is 7.734°C, so ΔTf = 7.734 − 5.43 = 2.304°C and m = 2.304/14.4 = 0.16. 0.16 = (2.6/M)×(1000/100), so M = 162.5.
Teacher's Note: ΔTf is the difference from the pure-solvent freezing point.
Exam Note: Printed '7.734°C/m' is the freezing point 7.734°C.
Question 61. C6H6 freezes at 5.5°C. At what temperature will a solution of 10.44 g of C4H10 in 200 g of C6H6 freeze? Kf (C6H6) = 5.12°C/m
(a) 4.608°C
(b) 0.892°C
(c) 5.5°C
(d) none of these
Solution. Answer: (b). n = 10.44/58 = 0.18 mol; m = 0.18×1000/200 = 0.9. ΔTf = 5.12×0.9 = 4.608°C. Tf = 5.5 − 4.608 = 0.892°C.
Teacher's Note: Subtract ΔTf from 5.5°C, do not report ΔTf itself.
Exam Note: Option (a) is the depression, not the freezing point.
Question 62. How much ethyl alcohol must be added to 1.0 L of water so that solution will not freeze at −4°F? (Kf = 1.86°C/m)
(a) < 20 g
(b) < 10.75 g
(c) < 494.5 g
(d) > 494.5 g
Solution. Answer: (d). −4°F = −20°C, so ΔTf = 20°C and m = 20/1.86 = 10.75 mol per kg water. Mass of C2H5OH = 10.75×46 = 494.5 g. To stay unfrozen at −20°C at least this much is needed, so the amount must be more than 494.5 g.
Teacher's Note: Convert −4°F to −20°C, then find molality needed.
Exam Note: Not freezing needs at least this amount: choose '>'.
Question 63. The freezing point of a solution of 2.40 g of biphenyl (C12H10) in 75.0 g of benzene (C6H6) is 4.40°C. The normal freezing point of benzene is 5.50°C. What is the molal freezing point constant (°C/m) for benzene?
(a) −5.3
(b) −5.1
(c) −4.6
(d) −4.8
Solution. Answer: (a) (from key). n = 2.40/154 = 0.01558 mol; m = 0.01558/0.075 = 0.2078; ΔTf = 5.50 − 4.40 = 1.10°C. Kf = 1.10/0.2078 = 5.3°C/m; the book prints it with a negative sign, −5.3.
Teacher's Note: Kf = ΔTf/m; sign in the options reflects the book's convention.
Exam Note: Magnitude 5.3; book lists it as −5.3.
Question 64. A solution containing 1.8 g of a compound (empirical formula CH2O) in 40 g of water is observed to freeze at −0.465°C. The molecular formula of the compound is (Kf of water = 1.86 kg K mol-1):
(a) C2H4O2
(b) C3H6
(c) C4H8O4
(d) C6H12O6
Solution. Answer: (d). m = 0.465/1.86 = 0.25 mol/kg, so in 40 g water there is 0.01 mol and M = 1.8/0.01 = 180. Empirical mass 30, n = 6, so C6H12O6.
Teacher's Note: Molar mass 180 divided by empirical mass 30 gives multiplier 6.
Exam Note: Always finish by multiplying the empirical formula.
Question 65. Freezing point of the following equilibrium, liquid solvent ⇌ solid solvent is:
(a) (ΔH − ΔG)/(TΔS)
(b) ΔH/ΔS
(c) ΔG/ΔS
(d) ΔS/ΔH
Solution. Answer: (b). At equilibrium ΔG = ΔH − TΔS = 0, so Tf = ΔH/ΔS.
Teacher's Note: Equilibrium means ΔG = 0, so T = ΔH/ΔS.
Exam Note: Set ΔG = 0 at a phase equilibrium.
Question 66. Freezing point of a solution is smaller than that point of a solvent. It is due to:
(a) ΔH of solution and solvent is almost identical since intermolecular forces between solvent molecules are involved
(b) ΔS of solution (between solution and solid) is larger than that of the ΔS of solvent (between solvent and solid)
(c) ΔS of the solution is smaller than that of the solvent
(d) ΔH of the solution is much higher than of solvent but ΔS of solution is smaller than that of the solvent
Solution. Answer: (b). Tf = ΔH/ΔS with nearly equal ΔH; because the solution is more disordered, its entropy change on freezing is larger, so its freezing temperature is lower.
Teacher's Note: Equal ΔH with larger ΔS gives lower Tf = ΔH/ΔS.
Exam Note: Link larger entropy change to lower freezing temperature.
Question 67. When 36.0 g of a solute having the empirical formula CH2O is dissolved in 1.20 kg of water, the solution freezes at −0.93°C. What is the molecular formula of the solute? (Kf = 1.86°C kg mol-1)
(a) C2H4O
(b) C2H2O2
(c) C2H4O3
(d) C2H4O2
Solution. Answer: (d). m = 0.93/1.86 = 0.5, so moles = 0.6 and M = 36/0.6 = 60. Empirical mass 30, n = 2, so C2H4O2.
Teacher's Note: M = 60 and empirical mass 30 give the formula double.
Exam Note: Check the formula's atom counts against CH2O × 2.
Question 68. Calculate the molecular weight of a substance whose 7.0% by mass solution in water freezes at −0.93°C. The cryoscopic constant of water is 1.86°C kg mol-1:
(a) 140 g mol-1
(b) 150.5 g mol-1
(c) 160 g mol-1
(d) 155 g mol-1
Solution. Answer: (b). 7.0% by mass means 7 g solute in 93 g water. m = 0.93/1.86 = 0.5, so (7/M)×(1000/93) = 0.5 and M = 150.5 g/mol.
Teacher's Note: 7% by mass means 93 g of solvent, not 100 g.
Exam Note: Solvent mass is 100 − 7 = 93 g.
Question 69. Camphor is often used in molecular mass determination because:
(a) it is readily available
(b) it has a very high cryoscopic constant
(c) it is volatile
(d) it is solvent for organic substances
Solution. Answer: (b). Camphor has a very high Kf (about 40 K kg mol-1), giving a large measurable depression even for small amounts of solute.
Teacher's Note: Large Kf magnifies ΔTf, improving accuracy (Rast method).
Exam Note: High Kf is the reason.
Question 70. For 1 molal solution of each compound minimum freezing point will be assuming complete ionisation in each case:
(a) [Fe(H2O)6]Cl3
(b) [Fe(H2O)5Cl]Cl2·H2O
(c) [Fe(H2O)4Cl2]Cl·2H2O
(d) [Fe(H2O)3Cl3]·3H2O
Solution. Answer: (a). Minimum freezing point means the most particles: (a) gives 4 ions, (b) 3, (c) 2, (d) 1 (non-ionic).
Teacher's Note: Count ions outside the coordination sphere: 4, 3, 2, 1.
Exam Note: Lowest freezing point needs largest i.
Question 71. For 1 molal solution of each compound maximum freezing point will be assuming complete ionisation in each case:
(a) [Fe(H2O)6]Cl3
(b) [Fe(H2O)5Cl]Cl2·H2O
(c) [Fe(H2O)4Cl2]Cl·2H2O
(d) [Fe(H2O)3Cl3]·3H2O
Solution. Answer: (d). Maximum freezing point means the fewest particles; the complex in (d) has all chlorides in the coordination sphere and does not ionise (i = 1).
Teacher's Note: Non-ionising complex has i = 1, the smallest depression.
Exam Note: Highest freezing point needs smallest i.
Question 72. PtCl4·6H2O can exist as a hydrated complex. Its 1 molal aq. solution has depression in freezing point of 3.72. Assume 100% ionisation and Kf(H2O) = 1.86°C mol-1 kg, then complex is:
(a) [Pt(H2O)6]Cl4
(b) [Pt(H2O)4Cl2]Cl2·2H2O
(c) [Pt(H2O)3Cl3]Cl·3H2O
(d) [Pt(H2O)2Cl4]·4H2O
Solution. Answer: (c). i = 3.72/(1.86×1) = 2, so the complex gives 2 ions: [Pt(H2O)3Cl3]+ and Cl-.
Teacher's Note: i = 2 means one complex ion plus one free chloride.
Exam Note: Count free ions: (a)5, (b)3, (c)2, (d)1.
Question 73. A complex is represented as CoCl3·xNH3. Its 0.1 molal solution in water shows ΔTf = 0.558 K. Kf for H2O is 1.86 K molality-1. Assuming 100% ionisation of complex and co-ordination number of Co is six, calculate formula of complex:
(a) [Co(NH3)6]Cl3
(b) [Co(NH3)5Cl]Cl2
(c) [Co(NH3)4Cl2]Cl
(d) none of these
Solution. Answer: (b). 0.558 = 1.86×0.1×i gives i = 3. Three ions means [Co(NH3)5Cl]2+ and 2Cl-, so the complex is [Co(NH3)5Cl]Cl2.
Teacher's Note: i = 3 and coordination number 6 fix five NH3 plus one Cl inside.
Exam Note: Total ligands inside must be six.
Question 74. The freezing point of equimolal aqueous solutions will be highest for:
(a) C6H5NH3Cl
(b) Ca(NO3)2
(c) La(NO3)3
(d) C6H12O6
Solution. Answer: (d). Depression in freezing point is smallest for the solute with the smallest van't Hoff factor; glucose is a non-electrolyte (i = 1), so its solution has the highest freezing point.
Teacher's Note: Smallest i gives smallest depression, hence highest freezing point.
Exam Note: Non-electrolyte has i = 1.
Question 75. The freezing point of a 4% aqueous solution of 'A' is equal to the freezing point of 10% aqueous solution of 'B'. If the molecular weight of 'A' is 60, then the molecular weight of 'B' will be:
(a) 160
(b) 90
(c) 45
(d) 180
Solution. Answer: (a). Equal freezing points mean equal molality: (4/60)×(1000/96) = (10/MB)×(1000/90), so MB = 160.
Teacher's Note: Equal freezing points mean equal molality; solvent masses are 96 g and 90 g.
Exam Note: Solvent mass = 100 − percent.
Question 76. Depression in freezing point of 0.01 molal aqueous HCOOH solution is 0.02046. 1 molal aqueous urea solution freezes at −1.86°C, assuming molality equal to molarity, pH of HCOOH solution is:
(a) 2
(b) 3
(c) 4
(d) 5
Solution. Answer: (b). Kf = 1.86. 0.02046 = 1.86×0.01×(1 + α), so α = 0.1. [H+] = 0.01×0.1 = 10-3 and pH = 3.
Teacher's Note: Find i from ΔTf, then α, then [H+] = Cα.
Exam Note: Urea data only provides Kf = 1.86.
Question 77. When mercuric iodide is added to the aqueous solution of KI, then the:
(a) freezing point is raised
(b) freezing point is lowered
(c) freezing point does not change
(d) boiling point does not change
Solution. Answer: (a). HgI2 + 2KI → K2HgI4 ⇌ 2K+ + HgI42−. The number of ions decreases, so the freezing point rises.
Teacher's Note: Complex formation removes ions, so fewer particles and a higher freezing point.
Exam Note: HgI2 is insoluble alone but dissolves via complex.
Question 78. Dimer of acetic acid in liquid benzene is in equilibrium with acetic acid monomer at certain temperature and pressure. If 25% of the dimer molecules are separated from the solution then:
(a) Freezing point of the solution reduces
(b) Average molar mass of solute increases
(c) Boiling point of solution increases
(d) Molar mass of solute decreases
Solution. Answer: (b) (from key). ΔTf = i Kf m and Mobs = M/i. As stated in the book's hint, removal of dimer decreases i, so the average molar mass of the solute increases (and the freezing point and boiling point change in the opposite sense to (a) and (c)).
Teacher's Note: Fewer particles lowers i, so observed molar mass M/i increases.
Exam Note: Mobs = M/i; a lower i raises it.
Question 79. The temperature of a city was found to be −9.3°C. A car was used, whose radiator was filled with 5 L of water. What quantity of antifreezing agent ethylene glycol were added to water of radiator in order to use the car for travelling? (Kf of water 1.86 K kg mol-1)
(a) 3200 g
(b) 1670 g
(c) 1550 g
(d) 2100 g
Solution. Answer: (c). ΔTf = 9.3 K, so m = 9.3/1.86 = 5 mol/kg. For 5 kg water: 25 mol of ethylene glycol (M = 62) = 25×62 = 1550 g.
Teacher's Note: Molality 5 on 5 kg water gives 25 mol of glycol.
Exam Note: Take 5 L water as 5 kg.
Question 80. The cryoscopic constant of water is 1.86 K kg mol-1. A 0.01 molal acetic acid solution produces a depression of 0.0194°C in the freezing point. The degree of dissociation of acetic acid is:
(a) zero
(b) 0.043
(c) 0.43
(d) 1
Solution. Answer: (b). i = 0.0194/(1.86×0.01) = 1.043, so α = i − 1 = 0.043.
Teacher's Note: For a 1:1 electrolyte, i = 1 + α.
Exam Note: Divide by Kf·m to get i.
Question 81. If 1m solution of benzoic acid in benzene has a freezing point depression of 2.4°C (Kf = 5.12°C mol-1 kg) and boiling point elevation of 2.53°C (Kb = 2.53°C mol-1 kg), then select the correct statement/s:
Statement I: there is dimer formation when undergoing freezing
Statement II: there is no change when undergoing boiling
Statement III: reverse of I and II
Statement IV: dimer formation in freezing and boiling state
(a) I, II
(b) II, III
(c) III, I
(d) only I
Solution. Answer: (a). On freezing, i = 2.4/5.12 = 0.47 < 1, so benzoic acid associates (dimerises). On boiling, i = 2.53/2.53 = 1, so no association: the dimers are broken at the higher temperature. Statements I and II are correct.
Teacher's Note: Compute i separately: 0.47 on freezing (association), 1.0 on boiling.
Exam Note: Compare observed with Kc·m for each property.
Question 82. In a 0.5 molal solution KCl, KCl is 50% dissociated. The freezing point of solution will be (Kf = 1.86 K kg mol-1):
(a) 274.674 K
(b) 271.60 K
(c) 273 K
(d) none of these
Solution. Answer: (b). i = 1 + α = 1.5. ΔTf = 1.86×0.5×1.5 = 1.395 K. Tf = 273 − 1.395 ≈ 271.6 K.
Teacher's Note: Subtract ΔTf from 273 K (pure water freezing point).
Exam Note: i = 1.5 for 50% dissociation of a 1:1 salt.
Question 83. A 1.0 g sample of Co(NH2CH2CH2NH2)3Cl3 is dissolved in 25.0 g of water and the freezing point of the solution is −0.87°C. How many ions are produced per mole of compound? The Kf of water is 1.86°C/molal.
(a) 2
(b) 3
(c) 4
(d) 5
Solution. Answer: (c). M = 345.5. m = (1/345.5)×(1000/25) = 0.1158. 0.87 = 1.86×i×0.1158, so i = 4: [Co(en)3]3+ + 3Cl-.
Teacher's Note: Compute molality from 1 g in 25 g water, then i = ΔTf/(Kfm).
Exam Note: Molar mass of the complex is 345.5 g/mol.
Question 84. An aqueous solution contains 3% and 1.8% by wt. urea and glucose respectively. What is the freezing point of solution? (Kf = 1.86°C/m)
(a) −1.172°C
(b) −2.27°C
(c) −1.5°C
(d) none of these
Solution. Answer: (a). In 100 g solution: 3 g urea (0.05 mol) and 1.8 g glucose (0.01 mol) in 95.2 g water. ΔTf = 1.86×(0.05 + 0.01)×1000/95.2 = 1.172°C, so Tf = −1.172°C.
Teacher's Note: Add moles of both non-electrolytes; solvent mass is 95.2 g.
Exam Note: Water mass = 100 − 3 − 1.8.
Question 85. Phenol associates in benzene to a certain extent in dimerisation reaction. A solution containing 0.02 kg of phenol in 1.0 kg of benzene has its freezing point depressed 0.69 K. Hence, degree of association of phenol dimerized will be: [Kf(C6H6) = 5.12 K kg mol-1]
(a) 0.63
(b) 0.73
(c) 0.83
(d) 0.93
Solution. Answer: (b). Normal ΔTf = 5.12×(20/94) = 1.0894 K. i = 0.69/1.0894 = 0.633. For dimerisation i = 1 − α/2, so α = 0.73.
Teacher's Note: i = observed/normal ΔTf; dimer: i = 1 − α/2.
Exam Note: M of phenol is 94 g/mol.
Question 86. Assuming complete ionisation, the solution having maximum freezing point will be:
(a) 1 M CaF2
(b) 1.5 M Al2(SO4)3
(c) 2 M NaCl
(d) 1 M AgNO3
Solution. Answer: (d). Particle concentrations: CaF2 3 M, Al2(SO4)3 7.5 M, NaCl 4 M, AgNO3 2 M. Fewest particles gives highest freezing point: AgNO3.
Teacher's Note: Multiply concentration by number of ions: smallest wins.
Exam Note: Highest freezing point needs smallest total particle concentration.
Question 87. In a 0.2 molal aqueous solution of a weak acid HX the degree of ionisation is 0.25. The freezing point of the solution will be nearest to: (Kf = 1.86 K kg mol-1)
(a) −0.26°C
(b) 0.465°C
(c) −0.48°C
(d) −0.465°C
Solution. Answer: (d). i = 1 + α = 1.25. ΔTf = 1.86×0.2×1.25 = 0.465, so Tf = −0.465°C.
Teacher's Note: Weak monoprotic acid: i = 1 + α.
Exam Note: Report freezing point as negative.
Question 88. An aqueous solution of 0.01 M KCl causes the same elevation in boiling point as an aqueous solution of urea causes the depression in freezing point. The concentration of urea solution is:
(a) 0.01 M
(b) 0.005 M
(c) 0.02 M
(d) 0.04 M
Solution. Answer: (c) (from key). KCl (i = 2) contributes 0.02 mol of particles per litre, so the urea solution that produces the equivalent colligative effect has concentration 0.02 M. (As printed, the question equates the two effects as equal concentrations; the key answer is 0.02 M.)
Teacher's Note: Equal colligative effect means equal particle concentration: 2×0.01.
Exam Note: KCl gives two particles per formula unit.
Question 89. When NaCl was dissolved in water, the freezing point depression was numerically equal to twice the molal depression constant. The relative lowering of vapour pressure of the solution is:
(a) 0.117
(b) 0.034
(c) 0.0585
(d) none of these
Solution. Corrected: answer (b) 0.034 (the printed key gives (a) 0.117, which wrongly uses the molar mass of NaCl, 58.5, in place of that of water). ΔTf = i Kf m = 2Kf, so i·m = 2. Relative lowering = i·n/(i·n + N) with N = 1000/18 = 55.56 mol per kg water: 2/(2 + 55.56) = 0.0347 ≈ 0.034.
Teacher's Note: Relative lowering uses moles of solvent (1000/18), not the solute molar mass.
Exam Note: Printed key (a) is wrong; use M of water.
Question 90. Which one of the following statements is false?
(a) The correct order of osmotic pressure for 0.01 M aqueous solution of each compound is BaCl2 > KCl > CH3COOH > sucrose
(b) Isotonic solutions are those solutions which have the same osmotic pressure
(c) Raoult's law states that the vapour pressure of a component over a solution is proportional to its mole fraction in liquid state
(d) Two sucrose solutions of same molality prepared in different solvents will have the same freezing point depression
Solution. Answer: (d). Freezing point depression ΔTf = Kfm depends on the solvent through Kf, so the same molality in different solvents gives different depressions. Statements (a), (b) and (c) are correct.
Teacher's Note: Kf is solvent-specific, so equal molality does not mean equal depression.
Exam Note: Different solvents have different Kf values.
Question 91. 0.1 molal aqueous solution of an electrolyte AB3 is 90% ionised. The boiling point of the solution at 1 atm is: (Kb(H2O) = 0.52 K kg mol-1)
(a) 273.19 K
(b) 374.92 K
(c) 376.4 K
(d) 373.19 K
Solution. Answer: (d). i = 1 + (4 − 1)×0.9 = 3.7. ΔTb = 0.52×0.1×3.7 = 0.19 K, so Tb = 373 + 0.19 = 373.19 K.
Teacher's Note: AB3 gives 4 ions, so i = 1 + 3α.
Exam Note: Add ΔTb to 373 K.
Question 92. Which of the following aqueous solutions has osmotic pressure nearest to pure solvent?
(a) Na2SO4
(b) BaCl2
(c) Al2(SO4)3
(d) C12H22O11
Solution. Answer: (d). Pure solvent has zero osmotic pressure, so the nearest solution is the one with the fewest particles (smallest i): sucrose, a non-electrolyte.
Teacher's Note: Smallest osmotic pressure belongs to the non-electrolyte (i = 1).
Exam Note: Pure solvent π = 0; choose smallest i.
Question 93. 0.1 M NaCl and 0.05 M BaCl2 solutions are separated by a semi-permeable membrane in a container. For this system, choose the correct answer:
(a) There is no movement of any solution across the membrane
(b) Water flows from BaCl2 solution towards NaCl solution
(c) Water flows from NaCl solution towards BaCl2 solution
(d) Osmotic pressure of 0.1 M NaCl is lower than the osmotic pressure of BaCl2 (assume complete dissociation)
Solution. Answer: (b). Particle concentrations: NaCl 0.1×2 = 0.20 M; BaCl2 0.05×3 = 0.15 M. The NaCl solution has the higher osmotic pressure, so water flows from the BaCl2 side to the NaCl side.
Teacher's Note: Solvent flows toward the solution with higher particle concentration.
Exam Note: Compare i·C: 0.20 versus 0.15.
Question 94. Two aqueous solutions, A and B, are separated by a semi-permeable membrane. The osmotic pressure of solution A immediately begins to decrease. Which of the following statement is true?
(a) The solvent molecules are moving from the solution of higher osmotic pressure to that of lower osmotic pressure.
(b) The initial osmotic pressure of solution B is greater than that of solution A.
(c) Solvent molecules are moving from solution B into solution A.
(d) Both (a) and (b) are true statements.
Solution. Answer: (c). The osmotic pressure of A falls because A is being diluted, so solvent moves from B into A. This means B has the lower osmotic pressure, so (a) and (b) are false.
Teacher's Note: A is diluted, so solvent enters A from B; solvent flows to higher π.
Exam Note: Solvent moves toward higher osmotic pressure.
Question 95. Which one of the following pairs of solution can we expect to be isotonic at the same temperature?
(a) 0.1 M urea and 0.1 M NaCl
(b) 0.1 M urea and 0.2 M MgCl2
(c) 0.1 M NaCl and 0.1 M Na2SO4
(d) 0.1 M Ca(NO3)2 and 0.1 M Na2SO4
Solution. Answer: (d). Particle concentrations: urea 0.1, NaCl 0.2, MgCl2 0.6, Na2SO4 0.3, Ca(NO3)2 0.3. Only Ca(NO3)2 and Na2SO4 match (0.3 each).
Teacher's Note: Isotonic means equal i·C; both salts here give 3 ions.
Exam Note: Multiply molarity by ions per formula unit.
Question 96. The empirical formula of a non-electrolyte is CH2O. A solution containing 3 g L-1 of the compound exerts the same osmotic pressure as that of 0.05 M glucose solution. The molecular formula of the compound is:
(a) CH2O
(b) C2H4O2
(c) C4H8O4
(d) C3H6O3
Solution. Answer: (b). Same osmotic pressure means 0.05 M, so M = 3/0.05 = 60 g/mol. Empirical mass 30, n = 2: C2H4O2.
Teacher's Note: Equal osmotic pressure means equal molarity 0.05 M.
Exam Note: Molar mass 60 divided by 30 gives 2.
Question 97. A semipermeable membrane used in the measurement of osmotic pressure of a solution allows the passage of:
(a) solute molecules through it
(b) solvent molecules through it
(c) both solvent and solute molecules
(d) either solvent or solute
Solution. Answer: (b). A semipermeable membrane passes only solvent molecules.
Teacher's Note: Only solvent crosses; that is what creates osmotic pressure.
Exam Note: Define semipermeable: solvent only.
Question 98. In the case of osmosis, solvent molecules move from:
(a) Higher vapour pressure to lower vapour pressure
(b) Higher concentration to lower concentration
(c) Lower vapour pressure to higher vapour pressure
(d) Higher osmotic pressure to lower osmotic pressure
Solution. Answer: (a). Solvent moves from the dilute solution (higher solvent vapour pressure, lower osmotic pressure) to the concentrated solution (lower vapour pressure, higher osmotic pressure).
Teacher's Note: Solvent flows to the side with lower solvent vapour pressure.
Exam Note: Dilute to concentrated; high to low vapour pressure.
Question 99. The osmotic pressures of equimolar solutions of urea, BaCl2 and AlCl3 will be in the order:
(a) AlCl3 > BaCl2 > urea
(b) BaCl2 > AlCl3 > urea
(c) urea > BaCl2 > AlCl3
(d) BaCl2 > urea > AlCl3
Solution. Answer: (a). At equal molarity π is proportional to i: AlCl3 (4) > BaCl2 (3) > urea (1).
Teacher's Note: Equal molarity: π follows the van't Hoff factor.
Exam Note: Count ions: 4, 3, 1.
Question 100. Which of the following solutions will have maximum osmotic pressure? Assume 90% dissociation of each salt:
(a) decinormal aluminium sulphate
(b) decinormal barium chloride solution
(c) decinormal sodium sulphate solution
(d) solution of equal volumes of decinormal barium chloride and decinormal sodium sulphate solutions
Solution. Answer: (a) (from key, taking 'decinormal' as 0.1 M). i for Al2(SO4)3 = 1 + 4×0.9 = 4.6 (particles 0.46); BaCl2 and Na2SO4 have i = 2.8 (0.28); the mixture in (d) also gives 0.28. Al2(SO4)3 has the largest value. (If 0.1 N were taken strictly, the three other solutions would tie; the key's answer follows the 0.1 M reading.)
Teacher's Note: Compute i·C with 90% dissociation: Al2(SO4)3 has most particles.
Exam Note: Check i = 1 + (n − 1)α for each salt.
Question 101. Consider 0.1 M solutions of two solutes X and Y. The solute X behaves as a univalent electrolyte while the solute Y dimerises in solution. Which of the following statements are correct regarding these solutions?
(1) The boiling point of the solution of X will be higher than that of Y
(2) The osmotic pressure of the solution of Y will be lower than that of X
(3) The freezing point of the solution of X will be lower than that of Y
(4) The relative lowering of vapour pressure of both the solutions will be the same
Select the correct answer from the option given below:
(a) 1, 2 and 3
(b) 2, 3 and 4
(c) 1, 2 and 4
(d) 1, 3 and 4
Solution. Answer: (a). X (univalent electrolyte) has i ≈ 2 and Y (dimerising) has i < 1. So X has the higher boiling point, higher osmotic pressure and lower freezing point; relative lowering of vapour pressure differs. Statements 1, 2 and 3 are correct.
Teacher's Note: X has i ≈ 2; dimerising Y has i < 1, so all colligative effects are larger for X.
Exam Note: Compare i: electrolyte versus associating solute.
Question 102. If Mnormal is the normal molecular mass and α is the degree of ionization of K3[Fe(CN)6], then the abnormal molecular mass of the complex in the solution will be:
(a) Mnormal(1 + 2α)-1
(b) Mnormal(1 + 3α)-1
(c) Mnormal(1 + α)-1
(d) equal to Mnormal
Solution. Answer: (b). K3[Fe(CN)6] ⇌ 3K+ + [Fe(CN)6]3−; total particles = 1 − α + 3α + α = 1 + 3α, so i = 1 + 3α and Mabnormal = Mnormal/(1 + 3α).
Teacher's Note: Four ions give i = 1 + 3α; observed mass = normal/i.
Exam Note: Abnormal mass = Mnormal/i.
Question 103. Equal volumes of 0.1 M urea and 0.1 M glucose are mixed. The mixture will have:
(a) lower osmotic pressure
(b) same osmotic pressure
(c) higher osmotic pressure
(d) none of these
Solution. Answer: (b). Both solutions are 0.1 M non-electrolytes; mixing equal volumes dilutes each to 0.05 M, so total concentration is again 0.1 M and the osmotic pressure is unchanged.
Teacher's Note: Total non-electrolyte concentration stays 0.1 M after mixing.
Exam Note: Add the diluted concentrations: 0.05 + 0.05.
Question 104. A 5% (W/V) solution of cane sugar (molecular weight = 342) is isotonic with 1% (W/V) solution of a substance X. The molecular weight of X is:
(a) 34.2
(b) 171.2
(c) 68.4
(d) 136.8
Solution. Answer: (c). Isotonic means equal molarity: 5/342 = 1/MX, so MX = 68.4.
Teacher's Note: Equal molarity: 5/342 = 1/M.
Exam Note: Isotonic solutions have equal molar concentration.
Question 105. Insulin is dissolved in a suitable solvent and the osmotic pressure (π) of solutions of various concentrations (g/cm3) C is measured at 20°C. The slope of a plot of π against C is found to be 4.65 × 10-3. The molecular weight of the insulin (g/mol) is:
(a) 3 × 105
(b) 9 × 105
(c) 4.5 × 105
(d) 5.16 × 106
Solution. Answer: (d). π = (C/M)RT, so slope = RT/M. With R = 0.082 L atm K-1 mol-1 and T = 293 K, M = 0.082×293/(4.65×10-3×10-3) ≈ 5.16×106 g/mol (the book's working keeps the factor 10-3 for converting g/cm3 to g/L).
Teacher's Note: Slope of π versus C is RT/M, so M = RT/slope.
Exam Note: Convert concentration units consistently.
Question 106. An aqueous solution of sucrose (C12H22O11) having a concentration of 34.2 gram/litre has an osmotic pressure of 2.38 atmospheres at 17°C. For an aqueous solution of glucose (C6H12O6) to be isotonic with this solution, its concentration should be:
(a) 34.2 gram per litre
(b) 17.1 gram per litre
(c) 18.0 gram per litre
(d) 36.0 gram per litre
Solution. Answer: (c). Sucrose: 34.2/342 = 0.1 M. Isotonic glucose solution must also be 0.1 M, i.e. 0.1×180 = 18.0 g per litre.
Teacher's Note: Isotonic means equal molarity: 0.1 M glucose is 18 g/L.
Exam Note: Convert molarity back to grams using M = 180.
Question 107. Which of the following experimental methods is adopted to determine osmotic pressure?
(a) Berkley-Hartley's method
(b) Beckmann's method
(c) Landsberger's method
(d) Differential method
Solution. Answer: (a). The Berkeley-Hartley method is used to measure osmotic pressure directly; Beckmann's and Landsberger's methods are for freezing point and boiling point respectively.
Teacher's Note: Berkeley-Hartley measures osmotic pressure; Beckmann and Landsberger measure ΔT.
Exam Note: Match each named method to its property.
Question 108. Based upon the technique of reverse osmosis the approximate pressure required to desalinate sea water containing 2.5% (mass/volume) KNO3 at 27°C will be
(a) 10.5 atm
(b) 21 atm
(c) 12.2 atm
(d) 6.09 atm
Solution. Answer: (c). 2.5% w/v means 25 g/L; M = 101, so 0.2475 mol/L. π = iCRT = 2×0.2475×0.0821×300 = 12.2 atm (the applied pressure must exceed this).
Teacher's Note: Reverse osmosis pressure must exceed π = iCRT with i = 2.
Exam Note: KNO3 gives two ions.
Question 109. A 1% (wt/vol) KCl solution is ionised to the extent of 80%. The osmotic pressure at 27°C of the solution will be:
(a) 6.95 atm
(b) 5.94 atm
(c) 2.71 atm
(d) 3.30 atm
Solution. Answer: (b). i = 1 + 0.8 = 1.8; C = (1/74.5)/0.1 L = 0.1342 M. π = iCRT = 1.8×0.1342×0.0821×300 = 5.94 atm.
Teacher's Note: 1% w/v is 10 g per litre; π = iCRT with i = 1.8.
Exam Note: Remember M of KCl is 74.5.
Question 110. Osmotic pressure of blood is 7.40 atm, at 27°C. Number of moles of glucose to be used per litre for an intravenous injection that is to have same osmotic pressure of blood is:
(a) 0.3
(b) 0.2
(c) 0.1
(d) 0.4
Solution. Answer: (a). C = π/RT = 7.40/(0.0821×300) = 0.30 mol/L.
Teacher's Note: Glucose is a non-electrolyte, so C = π/RT.
Exam Note: Use T = 300 K.
Question 111. The relationship between osmotic pressures (π1, π2 and π3) at a definite temperature when 1 g glucose, 1 g urea and 1 g sucrose are dissolved in 1 litre of water is (assume i = 1 for all):
(a) π1 > π2 > π3
(b) π3 > π1 > π2
(c) π2 > π1 > π3
(d) π2 > π3 > π1
Solution. Answer: (c). For equal masses π ∝ 1/M: urea (60) > glucose (180) > sucrose (342), so π2 > π1 > π3.
Teacher's Note: Equal mass: smaller molar mass means more moles, higher π.
Exam Note: Order by 1/M: 60, 180, 342.
Question 112. van't Hoff proved that osmotic pressure (π) is a colligative property. For an ideal solution, osmotic pressure (π) is helpful to determine the molecular mass of solute using MB = WBRT/(π·V). Law can be show by the curve (C = concentration):
(Four graphs: (a) π against T at constant C is a straight line through the origin rising upward; (b) π against T at constant C falls like a decaying curve; (c) π against C at constant T falls like a decaying curve; (d) π against C at constant T is a horizontal line.)
Solution. Answer: (a). π = CRT, so at constant C, π is directly proportional to T: a straight line through the origin (at constant T, π would also rise linearly with C).
Teacher's Note: π = CRT is linear in T at fixed C.
Exam Note: Direct proportionality gives a straight line through origin.
Question 113. A solution containing 4.0 g of PVC in 2 litre of dioxane (industrial solvent) was found to have an osmotic pressure 3.0 × 10-4 atm at 27°C. The molar mass of the polymer (g/mol) will be:
(a) 1.6 × 104
(b) 1.6 × 105
(c) 1.6 × 103
(d) 1.6 × 102
Solution. Answer: (b). M = WBRT/(πV) = 4.0×0.0821×300/(3.0×10-4×2) ≈ 1.6×105 g/mol.
Teacher's Note: Polymers have tiny π, so osmometry gives large molar masses.
Exam Note: Use R = 0.0821 L atm and T = 300 K.
Question 114. The osmotic pressures of 0.010 M solutions of KI and of sucrose (C12H22O11) are 0.432 atm and 0.24 atm respectively. The van't Hoff factor for KI is:
(a) 1.80
(b) 0.80
(c) 1.2
(d) 1.0
Solution. Answer: (a). i = π(KI)/π(sucrose) = 0.432/0.24 = 1.80 (sucrose has i = 1).
Teacher's Note: Sucrose is a non-electrolyte, so its π gives the baseline for i.
Exam Note: i is the ratio of osmotic pressures at equal concentration.
Question 115. What is the correct sequence of osmotic pressure of 0.01 M aq. solution of: (1) Al2(SO4)3 (2) Na3PO4 (3) BaCl2 (4) Glucose
(a) π4 > π2 > π3 > π1
(b) π3 > π4 > π2 > π1
(c) π3 > π4 > π1 > π2
(d) π1 > π2 > π3 > π4
Solution. Answer: (d). π ∝ i at equal molarity: Al2(SO4)3 (5) > Na3PO4 (4) > BaCl2 (3) > glucose (1).
Teacher's Note: At equal molarity, order by number of ions: 5, 4, 3, 1.
Exam Note: Count ions from each formula.
Question 116. 1.0 molar solution of the complex salt, CrCl3·6H2O, displays an osmotic pressure of 3RT. 0.5 L of the same solution on treatment with excess of AgNO3 solution will yield (assume α = 1):
(a) 0.5 mole of AgCl
(b) 1.0 mole of AgCl
(c) 1.5 mole of AgCl
(d) 3.0 mole of AgCl
Solution. Answer: (b). π = iCRT = 3RT with C = 1 M gives i = 3, so the complex ionises into 3 ions: [Cr(H2O)5Cl]Cl2·H2O → [Cr(H2O)5Cl]2+ + 2Cl-. 0.5 L of 1 M gives 0.5 mol of complex and 1.0 mol of free Cl-, hence 1.0 mol AgCl.
Teacher's Note: i = 3 shows two ionisable chlorides; only free Cl- precipitates with Ag+.
Exam Note: Coordinated chloride does not precipitate.
Question 117. A 0.010 g sample of Cr(NH3)4(SO4)Cl is dissolved in 25.0 mL of water and the osmotic pressure of the solution is 59.1 torr at 25°C. How many moles of ions are produced per mole of compound?
(a) 1
(b) 4
(c) 2
(d) 3
Solution. Answer: (c). M = 251.5 g/mol, so C = 0.010/251.5/0.025 L = 1.59×10-3 M. π = 59.1/760 = 0.0778 atm. i = π/(CRT) = 0.0778/(1.59×10-3×0.0821×298) = 2.0. The compound gives [Cr(NH3)4SO4]+ and Cl-.
Teacher's Note: Convert torr to atm and mass to molarity, then i = π/CRT.
Exam Note: Check units: 25 mL is 0.025 L.
Question 118. Which of the following aqueous solutions should have the highest osmotic pressure?
(a) 0.011 M AlCl3 at 50°C
(b) 0.03 M NaCl at 25°C
(c) 0.012 M (NH4)2SO4 at 25°C
(d) 0.03 M NaCl at 50°C
Solution. Answer: (d). π ∝ iCT: AlCl3 4×0.011×323 = 14.2; NaCl 2×0.03×298 = 17.9; (NH4)2SO4 3×0.012×298 = 10.7; NaCl at 50°C 2×0.03×323 = 19.4. Highest is (d).
Teacher's Note: Compare iCT (kelvin) across all four options.
Exam Note: Use absolute temperature, not °C.
Question 119. X3Y2 (i = 5) when reacted with A2B3 (i = 5) in aqueous solution gives brown colour. These are separated by a semipermeable membrane AB as shown (side X: 0.5 M X3Y2; side Y: 0.01 M A2B3). Due to osmosis there is:
(a) brown colour formation in side X
(b) brown colour formation in side Y
(c) formation in both of the sides X and Y
(d) no brown colour formation
Solution. Answer: (d). Osmosis moves only solvent (water) from the dilute side Y to the concentrated side X. Solute ions cannot cross the semipermeable membrane, so X3Y2 and A2B3 never meet and no brown colour forms.
Teacher's Note: Only solvent crosses a semipermeable membrane, so reactants stay apart.
Exam Note: Do not confuse osmosis with diffusion of solute.
Question 120. Which of the following curves represents the Henry's law?
(Four graphs of log m against log P: (a) a straight line with positive slope and a positive intercept on the log m axis; (b) a straight line with positive slope through the origin; (c) a straight line falling; (d) a decaying curve.)
Solution. Answer: (a). Henry's law m = kP gives log m = log k + log P: a straight line of slope 1 with intercept log k on the log m axis.
Teacher's Note: Take logs of m = kP: slope 1 and intercept log k.
Exam Note: Intercept is log k, so line does not pass through origin.
Question 121. According to Henry's law, the solubility of a gas in a given volume of liquid increases with increase in:
(a) Temperature
(b) Pressure
(c) Both (a) and (b)
(d) None of these
Solution. Answer: (b). Solubility of a gas is proportional to its pressure (m = kP); solubility decreases with temperature.
Teacher's Note: Solubility is directly proportional to pressure.
Exam Note: Gas solubility falls with rising temperature.
Question 122. At 300 K, 40 mL of O3(g) dissolves in 100 g of water at 1.0 atm. What mass of ozone dissolved in 400 g of water at a pressure of 4.0 atm at 300 K?
(a) 0.1 g
(b) 1.2 g
(c) 0.48 g
(d) 4.8 g
Solution. Answer: (d). Solubility ∝ pressure and ∝ mass of water: volume dissolved = 40×4×4 = 640 mL. n = (4×640×10-3)/(0.0821×300) = 0.104 mol ≈ 0.1 mol, so mass = 0.1×48 = 4.8 g.
Teacher's Note: Scale by both pressure (×4) and solvent mass (×4).
Exam Note: The book computes moles at 4 atm using PV = nRT.
Question 123. 1 kg of water under a nitrogen pressure of 1 atmosphere dissolves 0.02 gm of nitrogen at 293 K. Calculate Henry's law constant:
(a) 7.7 × 104 atm
(b) 7.7 × 103 atm
(c) 2 × 10-5 atm
(d) 2 × 10-2 atm
Solution. Answer: (a). n(N2) = 0.02/28 = 7.14×10-4 mol; n(H2O) = 1000/18 = 55.56 mol. x = 1.29×10-5. KH = P/x = 1/1.29×10-5 ≈ 7.7×104 atm.
Teacher's Note: Mole fraction of gas is tiny; KH = P/x is large.
Exam Note: Use mole fraction, not molality.
Question 124. According to Henry's law, the partial pressure of gas (Pg) is directly proportional to mole fraction of gas in liquid solution, Pgas = KH·Xgas, where KH is Henry's constant. Which is incorrect?
(a) KH is characteristic constant for a given gas-solvent system
(b) Higher is the value of KH, lower is solubility of gas for a given partial pressure of gas
(c) KH has temperature dependence
(d) KH decreases with increase of temperature
Solution. Answer: (d). KH increases with temperature because gas solubility decreases as temperature rises; statements (a), (b) and (c) are correct.
Teacher's Note: Higher KH means lower solubility; solubility drops as temperature rises, so KH rises.
Exam Note: Pick the false statement: KH does not decrease.
Question 125. At 760 torr pressure and 20°C temperature, 1 L of water dissolves 0.04 gm of pure oxygen or 0.02 gm of pure nitrogen. Assuming that dry air is composed of 20% oxygen and 80% nitrogen (by volume). The masses (in g/L) of oxygen and nitrogen dissolved by 1 L of water at 20°C exposed to air at a total pressure of 760 torr are respectively:
(a) 0.008, 0.016
(b) 0.016, 0.008
(c) 0.16, 0.08
(d) 0.04, 0.02
Solution. Answer: (a). Partial pressures are 0.2 atm (O2) and 0.8 atm (N2). Mass dissolved ∝ partial pressure: O2 = 0.04×0.2 = 0.008 g/L; N2 = 0.02×0.8 = 0.016 g/L.
Teacher's Note: Use partial pressure from volume fraction; solubility scales linearly.
Exam Note: Volume % equals mole % equals pressure fraction.
Level 2
Level 2, Question 1. Two beaker A and B present in a closed vessel. Beaker A contains 152.4 g aqueous solution of urea, containing 12 g of urea. Beaker B contains 196.2 g glucose solution, containing 18 g of glucose. Both solutions allowed to attain the equilibrium. Determine wt. % of glucose in its solution at equilibrium:
(a) 6.71
(b) 14.49
(c) 16.94
(d) 20
Solution. Answer: (b). Urea: 12 g = 0.2 mol in 140.4 g water (7.8 mol); x = 0.025. Glucose: 18 g = 0.1 mol in 178.2 g water (9.9 mol); x = 0.01. Glucose solution has the higher vapour pressure, so water transfers from B to A until mole fractions are equal. Let x mol of water move: 0.2/(0.2 + 7.8 + x) = 0.1/(0.1 + 9.9 − x), so x = 4. Water left in B = 9.9 − 4 = 5.9 mol = 106.2 g. Solution B mass = 18 + 106.2 = 124.2 g and wt. % glucose = 18/124.2×100 = 14.49%.
Teacher's Note: Water moves to equalise mole fractions of solute in both beakers.
Exam Note: Set equal solute mole fractions; solve for water moved.
Level 2, Question 2. Two components A and B form an ideal solution. The mole fractions of A and B in ideal solution are XA and XB, while that of in vapour phase, these components have their mole fractions as YA and YB. Then, the slope and intercept of plot of 1/YA vs. 1/XA will be:
(a) PA°/PB°, (PB° − PA°)/PB°
(b) PB°/PA°, (PA° − PB°)/PA°
(c) PB°/PA°, PB°/(PB° − PA°)
(d) PA° − PB°, PA°/PB°
Solution. Answer: (b). YA = PA°XA/[XA(PA° − PB°) + PB°], so 1/YA = ((PA° − PB°)/PA°) + (PB°/PA°)(1/XA). Slope = PB°/PA° and intercept = (PA° − PB°)/PA°.
Teacher's Note: Same derivation as Level 1 Q7, now asking for the intercept too.
Exam Note: State slope and intercept both.
Level 2, Question 3. At 48°C, the vapour pressure of pure CS2 is 850 torr. A solution of 2.0 g of sulphur in 100 g of CS2 has a vapour pressure 844.9 torr. Determine the atomicity of sulphur molecule:
(a) 1
(b) 2
(c) 4
(d) 8
Solution. Answer: (d). (P° − P)/P = (850 − 844.9)/844.9 = (2/M)×(76/100) with M of CS2 = 76, so MS ≈ 252. Atomicity = 252/32 ≈ 8 (S8).
Teacher's Note: Atomicity equals molar mass of sulphur molecule divided by atomic mass 32.
Exam Note: Use (P° − P)/P form and M(CS2) = 76.
Level 2, Question 4. An ideal solution contains two volatile liquids A (P° = 100 torr) and B (P° = 200 torr). If mixture contain 1 mole of A and 4 mole of B then total vapour pressure of the distillate is:
(a) 150
(b) 180
(c) 188.88
(d) 198.88
Solution. Answer: (c). Liquid: xA = 1/5, xB = 4/5; PA = 20, PB = 160 torr, total 180 torr. Vapour: yA = 20/180 = 1/9, yB = 8/9. The distillate (condensed vapour) has xA = 1/9, xB = 8/9, so Ptotal = 100×(1/9) + 200×(8/9) = 188.88 torr.
Teacher's Note: Distillate composition equals vapour composition of the first liquid.
Exam Note: Recompute vapour pressure for the new composition.
Level 2, Question 5. The vapour pressure of two pure liquids A and B, that form an ideal solution are 100 and 900 torr respectively at temperature T. This liquid solution of A and B is composed of 1 mole of A and 1 mole of B. What will be the pressure, when 1 mole of mixture has been vaporized?
(a) 800 torr
(b) 500 torr
(c) 300 torr
(d) None of these
Solution. Answer: (c). Let nB mol of B be in the vapour, so yB = nB (1 mol vaporised) and xB in the remaining liquid = (1 − nB)/1. With P = PA° + (PB° − PA°)xB and yB = PB°xB/P, the book shows nB = PB°/(P + PB°) leads to P = √(PA°·PB°) = √(100×900) = 300 torr.
Teacher's Note: Mass balance with two Raoult relations gives P = √(PA°PB°).
Exam Note: Derivation relies on moles vaporised equals moles left.
Level 2, Question 6. Which of the following represents correctly the changes in thermodynamic properties during the formation of 1 mole of an ideal binary solution:
(Four plots against mole fraction, J mol-1 on the y-axis around zero: (a) ΔGmix on top (positive), TΔSmix in the middle, ΔHmix at the bottom; (b) ΔGmix on top, ΔHmix in the middle, TΔSmix at the bottom; (c) TΔSmix positive on top, ΔHmix zero in the middle, ΔGmix negative at the bottom; (d) TΔSmix on top, ΔGmix in the middle, ΔHmix at the bottom.)
Solution. Answer: (c). For an ideal solution ΔHmix = 0, ΔSmix > 0 so TΔSmix is positive, and ΔGmix = −TΔSmix is negative with the same magnitude. This matches plot (c).
Teacher's Note: Ideal mixing: ΔH = 0, ΔS positive, ΔG = −TΔS negative.
Exam Note: ΔGmix mirrors TΔSmix below the axis.
Level 2, Question 7. A saturated solution of XCl3 has a vapour pressure 17.20 mm Hg at 20°C, while pure water vapour pressure is 17.25 mm Hg. Solubility product (Ksp) of XCl3 at 20°C is:
(a) 9.8 × 10-2
(b) 10-5
(c) 2.56 × 10-6
(d) 7 × 10-5
Solution. Answer: (d). XCl3 gives i = 4. (P° − P)/P = i·m·18/1000: (17.25 − 17.20)×1000/(17.2×18) = 0.1615 = 4m, so m ≈ 0.04 and S ≈ 0.04 mol/L (dilute: molality ≈ molarity). Ksp = S·(3S)3 = 27S4 = 27×(0.0404)4 ≈ 7×10-5.
Teacher's Note: Vapour pressure lowering gives total ion molality; divide by 4 to get S.
Exam Note: Ksp = 27S4 for an AB3 salt.
Level 2, Question 8. A certain non-volatile electrolyte contains 40% carbon, 6.7% hydrogen and 53.3% oxygen. An aqueous solution containing 5% by mass of the solute boils at 100.15°C. Determine the molecular formula of the compound (Kb = 0.51°C/m):
(a) HCHO
(b) CH3OH
(c) C2H5OH
(d) C6H12O6
Solution. Answer: (d). Mole ratio C : H : O = 40/12 : 6.7/1 : 53.3/16 = 1 : 2 : 1, so empirical formula CH2O. m = 0.15/0.51 = 0.294; 5 g solute in 95 g water gives (5/M)(1000/95) = 0.294, so M ≈ 180. n = 180/30 = 6, so C6H12O6.
Teacher's Note: Empirical formula from percentages, then molar mass from ΔTb.
Exam Note: 5% by mass means 95 g of water.
Level 2, Question 9. A 0.10 M solution of a monoprotic acid (d = 1.01 g/cm3) is 5% ionised. The mol. wt. of the acid is 300 and Kf(H2O) = 1.86°C/m. What is the freezing point of the solution?
(a) −0.189°C
(b) −0.194°C
(c) −0.199°C
(d) None of these
Solution. Answer: (c). 1 L of solution weighs 1010 g and contains 0.1×300 = 30 g acid, so solvent = 980 g. m = 0.1/0.98 = 0.102. i = 1 + α = 1.05. ΔTf = 1.05×1.86×0.102 = 0.199°C, so Tf = −0.199°C.
Teacher's Note: Convert molarity to molality using density: solvent mass 980 g.
Exam Note: Include i = 1.05 for 5% ionisation.
Level 2, Question 10. An aqueous solution boils at 101°C. What is the freezing point of the same solution? (Given: Kf = 1.86°C/m and Kb = 0.51°C/m)
(a) 3.647°C
(b) −3.647°C
(c) −0.364°C
(d) None of these
Solution. Answer: (b). ΔTb = 1°C = Kb·meff, so meff = 1/0.51. ΔTf = Kf·meff = 1.86/0.51 = 3.647°C, so Tf = −3.647°C.
Teacher's Note: Same effective molality for both properties: ΔTf/ΔTb = Kf/Kb.
Exam Note: Give the freezing point as negative.
Level 2, Question 11. An industrial waste water is found to contain 8.2% Na3PO4 and 12% MgSO4 by weight in solution. If % ionisation of Na3PO4 and MgSO4 are 50 and 60 respectively then it's normal boiling point is [Kb(H2O) = 0.50 K kg mol-1]:
(a) 102.3°C
(b) 103.35°C
(c) 101.785°C
(d) None of these
Solution. Answer: (c). For Na3PO4: i = 1 + 3×0.5 = 2.5; for MgSO4: i = 1 + 0.6 = 1.6. In 100 g solution: 8.2 g Na3PO4 (M = 164, 0.05 mol) and 12 g MgSO4 (M = 120, 0.1 mol) in 79.8 g water. ΔTb = 0.50×[(0.05×2.5 + 0.1×1.6)/79.8]×1000 = 1.785°C, so Tb = 101.785°C.
Teacher's Note: Sum effective moles (i·n) of both salts over solvent mass 79.8 g.
Exam Note: Solvent mass is 100 − 8.2 − 12.
Level 2, Question 12. Ratio of ΔTb/Kb of 10 g AB2 and 14 g A2B per 100 g of solvent in their respective, solution (AB2 and A2B both are non-electrolytes) is 1 mol/kg in both cases. Hence, atomic wt. of A and B respectively are:
(a) 100, 40
(b) 60, 20
(c) 20, 60
(d) None of these
Solution. Answer: (b). ΔTb/Kb = m = 1, so 1 = (1000×10)/(100×MAB2), giving MAB2 = 100, and similarly MA2B = 140. Then A + 2B = 100 and 2A + B = 140, so A = 60 and B = 20.
Teacher's Note: Molality 1 fixes each molar mass; solve two simultaneous equations.
Exam Note: Form A + 2B = 100, 2A + B = 140.
Level 2, Question 13. The freezing point of a solution containing 0.2 g of acetic acid in 20.0 g benzene is lowered by 0.45°C. Calculate the degree of dimerization of acetic acid in benzene. Kf for benzene is 5.12 K mol-1 kg:
(a) 0.527
(b) 0.80
(c) 0.945
(d) None of these
Solution. Answer: (c). Mobs = 1000×Kf×w/(ΔT×W) = 1000×5.12×0.2/(20×0.45) = 113.78. For 2CH3COOH ⇌ (CH3COOH)2: Mnormal/Mobs = 1 − α + α/2 = 1 − α/2. 60/113.78 = 0.527 = 1 − α/2, so α = 0.945.
Teacher's Note: Association: i = 1 − α/2 = Mnormal/Mobs (not 1 + α/2).
Exam Note: Degree of association near 0.945 means nearly all dimerised.
Level 2, Question 14. If boiling point of an aqueous solution is 100.1°C, what is its freezing point? Given, enthalpy of fusion and vaporisation of water are 80 cal g-1 and 540 cal g-1 respectively:
(a) 0.361°C
(b) −0.361°C
(c) −3.61°C
(d) None of these
Solution. Answer: (b). Kb = RTb²/(1000Lv) and Kf = RTf²/(1000Lf), so ΔTb/ΔTf = Tb²Lf/(Tf²Lv). 0.1/ΔTf = (373×373×80)/(273×273×540), giving ΔTf = 0.361, so Tf = −0.361°C.
Teacher's Note: Express Kb and Kf via latent heats; ratio gives ΔTf.
Exam Note: Use kelvin temperatures in the ratio.
Level 2, Question 15. 100 g of C6H12O6 (aq.) solution has vapour pressure is equal to 40 torr at certain temperature. Vapour pressure of H2O(l) is 40.8 torr at same temperature. If this solution is cooled to −0.93°C, what mass of ice will be separated out? (Kf = 1.86 kg mol-1)
(a) 95.5 g
(b) 4.5 g
(c) 45.5 g
(d) 47.8 g
Solution. Answer: (d) 47.8 g (printed key). The book takes the initial molality as 0.25 m, so 100 g solution holds 4.31 g glucose and 95.69 g water. At −0.93°C the molality is 0.93/1.86 = 0.5 m, so 4.31 g glucose needs (1000/90)×4.31 = 47.88 g water. Ice separated = 95.69 − 47.88 = 47.8 g. (Note: the printed vapour pressures actually give (P° − P)/P = 0.02, i.e. m = 1.11, not 0.25; the book's 0.25 uses 80 where the molar mass of water, 18, belongs. The printed answer is kept as it is the intended one; see report.)
Teacher's Note: Ice separates until the remaining solution reaches molality 0.5 at −0.93°C.
Exam Note: Mass of ice = original water − water remaining.
Level 2, Question 16. 1.0 g of a monobasic acid HA in 100 g water lowers the freezing point by 0.155 K. If 0.75 g, of same acid requires 15 mL of N/5 NaOH solution for complete neutralisation then %, degree of ionisation of acid is: (Kf of H2O = 1.86 K kg mol-1)
(a) 20%
(b) 25%
(c) 40%
(d) 50%
Solution. Answer: (b) 25% (printed key). Mobserved = 1.86×1×1000/(0.155×100) = 120. The book takes Mnormal = 150 from the titration, so i = 150/120 = 1.25 and α = 0.25 = 25%. (Note: 15 mL of N/5 NaOH is 3 meq, which would give 0.75 g/3 meq = 250, not 150; the printed answer is kept, see report.)
Teacher's Note: i = normal/observed molar mass; for HA, α = i − 1.
Exam Note: Equivalent weight from titration gives normal molar mass.
Level 2, Question 17. 0.1 M KI and 0.2 M AgNO3 are mixed in 3 : 1 volume ratio. The depression of freezing point of the resulting solution will be [Kf(H2O) = 1.86 K kg mol-1]:
(a) 3.72 K
(b) 1.86 K
(c) 0.93 K
(d) 0.279 K
Solution. Answer: (d). Take 3 L of 0.1 M KI (0.3 mol) and 1 L of 0.2 M AgNO3 (0.2 mol): 0.2 mol AgI precipitates, leaving 0.1 mol KI and forming 0.2 mol KNO3. Ions in solution: 0.1×2 + 0.2×2 = 0.6 mol in 4 L, so concentration 0.6/4 = 0.15 M ≈ 0.15 m. ΔTf = 1.86×0.15 = 0.279 K.
Teacher's Note: Precipitation removes AgI; count remaining ions: K+, I-, NO3-.
Exam Note: AgI is insoluble and contributes no ions.
Level 2, Question 18. If 0.1 M H2SO4 (aq.) solution shows freezing point −0.3906°C then what is the Ka2 for H2SO4? (Assume m = M and Kf(H2O) = 1.86 K kg mol-1)
(a) 0.122
(b) 0.0122
(c) 1.11 × 10-3
(d) None of these
Solution. Answer: (b). ΔTf = i Kf m gives 0.3906 = i×1.86×0.1, so i = 2.1. The first dissociation is complete: H2SO4 → H+ + HSO4−. For the second step HSO4− ⇌ H+ + SO42− with degree α: total particles = C(1 − α) + Cα + Cα + C, so i = 2 + α = 2.1 and α = 0.1. Ka2 = [H+][SO42−]/[HSO4−] = (0.11×0.01)/0.09 = 0.0122.
Teacher's Note: First step is complete; i = 2 + α gives α for the second step.
Exam Note: Include H+ from step one in Ka2.
Level 2, Question 19. A living cell contains a solution which is isotonic with 0.2 M glucose solution. What osmotic pressure develops when the cell is placed in 0.05 M BaCl2 solution at 300 K?
(a) 1.23 atm
(b) 3.69 atm
(c) 6.15 atm
(d) None of these
Solution. Answer: (a). Cell solution ≡ 0.2 M particles. BaCl2 0.05 M gives 0.15 M particles. Net osmotic pressure = (0.2 − 0.15)×0.0821×300 = 1.23 atm.
Teacher's Note: Net π is the difference between cell and external particle concentrations.
Exam Note: Use i = 3 for BaCl2; subtract concentrations.
Level 2, Question 20. What is the osmotic pressure of 0.2 M HX (aq.) solution at 300 K? (Given: Ka(HX) = 8 × 10-5)
(a) 4.926 atm
(b) 0.5024 atm
(c) 5.024 atm
(d) None of these
Solution. Answer: (c). α = √(Ka/C) = √(8×10-5/0.2) = 0.02, so i = 1.02. π = iCRT = 1.02×0.2×0.0821×300 = 5.024 atm.
Teacher's Note: Weak acid: α = √(Ka/C), then i = 1 + α.
Exam Note: Remember the i factor in π = iCRT.
Level 2, Question 21. A solution contain 8 g of a carbohydrate in 100 g of water has a density 1.025 g/mL and an osmotic pressure of 5 atm at 27°C. What is the molar mass of the carbohydrate?
(a) 387
(b) 374
(c) 3740
(d) None of these
Solution. Answer: (b). Solution mass = 108 g, volume = 108/1.025 mL = 105.4 mL. π = (n/V)RT: 5 = (8/M)×(1000×1.025/108)×0.0821×300, giving M ≈ 374 g/mol.
Teacher's Note: Use solution volume from density (108 g ÷ 1.025), not solvent volume.
Exam Note: Carbohydrate is a non-electrolyte, so i = 1.
Level 2, Question 22. Study the following figure and choose the correct options. Assuming complete dissociation of electrolyte: (a semipermeable membrane separates 0.05 M aq. Al2(SO4)3 solution on the left from 0.10 M aq. MgCl2 solution on the right)
(a) There will be no net moment of any substance across the membrane
(b) MgCl2 will flow towards the Al2(SO4)3 solution
(c) Al2(SO4)3 will flow towards the MgCl2 solution
(d) The π (osmotic pressure) of 0.1 M MgCl2 is higher than the π of 0.05 M Al2(SO4)3
Solution. Answer: (d). Particle concentrations: MgCl2 0.1×3 = 0.30 M; Al2(SO4)3 0.05×5 = 0.25 M. So MgCl2 has the higher π and solvent (water) flows towards it; no solute crosses the membrane, so (a), (b) and (c) are wrong.
Teacher's Note: Compare i·C: 0.30 versus 0.25; only solvent crosses the membrane.
Exam Note: Solute never flows through a semipermeable membrane.
Level 2, Question 23. The total vapour pressure of a 4 mole % solution of NH3 in water at 293 K is 50.0 torr, the vapour pressure of pure water is 17.0 torr at this temperature. Applying Henry's and Raoult's law, calculate the total vapour pressure for a 5 mole % solution:
(a) 58.25 torr
(b) 33 torr
(c) 42.1 torr
(d) 52.25 torr
Solution. Answer: (a). For 4 mole %: Pwater = 0.96×17.0 = 16.32 torr, so PNH3 = 50.0 − 16.32 = 33.68 torr and KH = 33.68/0.04 = 842 torr. For 5 mole %: PNH3 = 842×0.05 = 42.1 torr and Pwater = 17×0.95 = 16.15 torr. Total = 42.1 + 16.15 = 58.25 torr.
Teacher's Note: Raoult for solvent, Henry for solute: find KH from the 4% data first.
Exam Note: Add both partial pressures at 5 mole %.
Level 2, Question 24. The vapour pressure of two pure liquids A and B which form an ideal solution are 500 and 800 torr respectively at 300 K. A liquid solution of A and B for which the mole fraction of A is 0.60 is contained in a cylinder closed by a piston on which the pressure can be varied. The solution is slowly vaporized at 300 K by decreasing the applied pressure. The composition of vapour when first bubble formed is:
(a) yA = 0.6; yB = 0.4
(b) yA = 0.48; yB = 0.52
(c) yA = 0.52; yB = 0.48
(d) yA = 0.5; yB = 0.5
Solution. Answer: (b). P = 500×0.6 + 800×0.4 = 620 torr. yA = 300/620 = 0.48 and yB = 0.52.
Teacher's Note: First bubble has the composition of vapour over the original liquid.
Exam Note: y = partial pressure ÷ total pressure.
Level 2, Question 25. (Same data as Question 24.) What is the composition of last droplet of liquid remaining in equilibrium with vapour?
(a) xA = 0.6; xB = 0.4
(b) xA = 0.5; xB = 0.5
(c) xA = 0.7; xB = 0.3
(d) xA = 0.3; xB = 0.7
Solution. Answer: (c). When almost all liquid has vaporised, the vapour has the original composition, yA = 0.6. Then 0.6 = 500xA/[500xA + 800(1 − xA)], which gives xA = 0.70 and xB = 0.30.
Teacher's Note: Last droplet is in equilibrium with vapour of the original composition.
Exam Note: Solve yA = 0.6 for xA.
Level 3: Passage Based Questions
Passage 1, Question 1. Passage 1: Lowering of vapour pressure is determined by the Ostwald and Walker dynamic method. When air is allowed to pass through a solvent or solution, it takes up solvent vapour with it to get itself saturated at that temperature. Containers I (liquid solution) and II (pure solvent) are weighed separately before and after passing dry air, and a tube of anhydrous CaCl2 then absorbs the moisture. Loss in mass of each set gives the lowering of vapour pressure. The temperature of air, the solution and the solvent is kept constant.
Loss in mass of solvent (wII) will be proportional to:
(a) P° − P
(b) P − P°
(c) P/P°
(d) P × P°
Solution. Answer: (a). Air leaves the solution saturated at pressure P, and the pure solvent then supplies the additional vapour needed to bring it to P°, so the loss in mass of the solvent wII ∝ (P° − P).
Teacher's Note: Solution supplies vapour ∝ P; pure solvent supplies the shortfall P° − P.
Exam Note: Loss from container II is the difference P° − P.
Passage 1, Question 2. Gain in mass of anhydrous CaCl2 is proportional to:
(a) P
(b) P°
(c) P − P°
(d) P° − P
Solution. Answer: (b). The air leaving container II is saturated at P°, so the CaCl2 tube absorbs vapour in proportion to P°.
Teacher's Note: Fully saturated air carries vapour proportional to P°.
Exam Note: CaCl2 absorbs everything: ∝ P° (= wI + wII).
Passage 1, Question 3. (P° − P)/P° is equal to:
(a) wI/(wI + wII)
(b) wII/(wI + wII)
(c) wI/(wI − wII)
(d) wII/wI
Solution. Answer: (b). wII ∝ (P° − P) and the gain in CaCl2 ∝ P° = wI + wII, so (P° − P)/P° = wII/(wI + wII).
Teacher's Note: Ratio of loss in solvent to total gain in drying agent.
Exam Note: Total moisture absorbed = wI + wII.
Passage 1, Question 4. Dry air was passed through 9.24 g of solute in 108 g of water and then through pure water. The loss in weight of solution was 3.2 g and that of pure water was 0.08 g. The molecular weight (g/mol) of solute is nearly:
(a) 50
(b) 62
(c) 70
(d) 80
Solution. Answer: (b). (P° − P)/P° = 0.08/(3.2 + 0.08) = 0.0244 = n/(n + N) with N = 108/18 = 6 mol. So n ≈ 0.150 mol and M = 9.24/0.150 ≈ 62 g/mol.
Teacher's Note: Relative lowering = wII/(wI + wII) = n/(n + N).
Exam Note: Moles of water N = 108/18 = 6.
Passage 2, Question 1. Passage 2: A dilute solution contains 'x' moles of solute A in 1 kg of solvent with molal elevation constant Kb. The solute dimerises in the solution according to the following equation: 2A ⇌ A2. The degree of association is (α).
The van't Hoff factor will be:
(a) i = 1 − 2α
(b) i = 1 − α/2
(c) i = 1 + α/2
(d) i = 1 + α
Solution. Answer: (b). Start with 1 mol A: 1 − α remains and α/2 mol of A2 forms, so total = 1 − α/2 and i = 1 − α/2.
Teacher's Note: Dimerisation halves the moles of the associated part: α → α/2.
Exam Note: Count particles at equilibrium: 1 − α + α/2.
Passage 2, Question 2. The molecular weight observed will be:
(a) greater than actual molecular weight
(b) lesser than actual molecular weight
(c) equal to the actual molecular weight
(d) cannot be predicted by the data given
Solution. Answer: (a). Association reduces the number of particles, so i < 1 and Mobserved = Mnormal/i is greater than the actual molecular weight.
Teacher's Note: Fewer particles means colligative property smaller, so apparent molar mass larger.
Exam Note: Association leads to higher observed molar mass.
Passage 2, Question 3. The degree of association is equal to:
(a) α = (Kbx − ΔTb)/(ΔTb·2)
(b) α = 2(Kbx − ΔTb)/(Kbx)
(c) α = 2 + 2ΔTb/(Kbx)
(d) α = ΔTb/(2Kbx)
Solution. Answer: (b). ΔTb = iKbx = Kbx(1 − α/2), so α/2 = (Kbx − ΔTb)/(Kbx) and α = 2(Kbx − ΔTb)/(Kbx).
Teacher's Note: Rearrange ΔTb = Kbx(1 − α/2) for α.
Exam Note: Molality equals x since solvent is 1 kg.
One or More Answers is/are Correct
One or More Correct, Question 1. Which of the following statement(s) is/are correct, if intermolecular forces in liquids A, B and C are in the order of A < B < C?
(a) B evaporates more readily than A
(b) B evaporates more readily than C
(c) A evaporates more readily than C
(d) all evaporate at same rate at constant temperature.
Solution. Answer: (b), (c). Weaker intermolecular forces mean easier evaporation: A > B > C in volatility. So B evaporates more readily than C and A more readily than C.
Teacher's Note: Weaker attractions give faster evaporation: A fastest, C slowest.
Exam Note: Order volatility opposite to intermolecular force strength.
One or More Correct, Question 2. When non-volatile solute is added to a pure solvent, the:
(a) vapour pressure of the solution becomes lower than the vapour pressure of the pure solvent
(b) rate of evaporation of solvent is reduced
(c) solute does not affect the rate of condensation
(d) none of these
Solution. Answer: (a), (b), (c). Solute particles occupy part of the surface, reducing the rate of evaporation and hence the vapour pressure, while the rate of condensation depends only on the vapour and is unchanged.
Teacher's Note: Solute at surface slows evaporation only; condensation rate depends on vapour.
Exam Note: Vapour pressure falls because evaporation slows.
One or More Correct, Question 3. The total vapour pressure of a binary solution is given by P = (100XA + 260XB) mm Hg, where XA and XB are the mole fractions of components A and B. This indicates that the:
(a) vapour pressure of solution is less than the pure B component
(b) vapour pressure of solution is more than that of pure A component
(c) vapour pressure of pure A is 100 mm Hg and that of pure B is 260 mm Hg
(d) the vapour pressure of pure A and B are 260 mm Hg and 100 mm Hg respectively
Solution. Answer: (a), (b), (c). The coefficients are the pure-component vapour pressures: PA° = 100 and PB° = 260 mm Hg. Any mixture lies between 100 and 260 mm Hg, so it is below pure B and above pure A.
Teacher's Note: Coefficients of XA and XB are the pure vapour pressures.
Exam Note: Mixture pressure lies between the two pure values.
One or More Correct, Question 4. Which of the following is correct for an ideal solution?
(a) ΔHmix = 0 and ΔVmix = 0
(b) ΔVmix = 0 and ΔSmix > 0
(c) ΔHmix > 0 and ΔSmix > 0
(d) ΔGmix = 0 and ΔSmix > 0
Solution. Corrected: (a), (b) only (the printed key gives (a), (b), (d)). For an ideal solution ΔHmix = 0, ΔVmix = 0, ΔSmix > 0 and ΔGmix = −TΔSmix < 0. Option (d) is wrong because ΔGmix is negative, not zero.
Teacher's Note: Ideal mixing is spontaneous: ΔG negative, driven by entropy.
Exam Note: ΔGmix = 0 is wrong; it is negative.
One or More Correct, Question 5. For a non-ideal solution with a negative deviation:
(a) ΔHmix = −ve
(b) ΔVmix = −ve
(c) ΔSmix = −ve
(d) ΔGmix = −ve
Solution. Answer: (a), (b), (d). Negative deviation arises from stronger A-B interactions, so mixing is exothermic (ΔH < 0) with volume contraction (ΔV < 0) and is spontaneous (ΔG < 0); ΔSmix remains positive.
Teacher's Note: Stronger A-B forces: heat released, volume shrinks, process spontaneous.
Exam Note: Entropy of mixing stays positive.
One or More Correct, Question 6. A binary solution of liquids A and B will show positive deviation from Raoult's law if it fulfils the following condition:
(a) PA > XAPA° and PB > XBPB°
(b) The intermolecular forces of A-B < A-A, B-B
(c) ΔH mixing is positive
(d) ΔV mixing is negative
Solution. Answer: (a), (b), (c). Positive deviation means partial pressures exceed Raoult values, A-B forces are weaker, ΔHmix > 0 and ΔVmix > 0 (not negative).
Teacher's Note: Weaker A-B forces raise partial pressures; endothermic mixing with expansion.
Exam Note: ΔV is positive for positive deviation.
One or More Correct, Question 7. Which of the following statements is/are correct about acetone and trichloromethane mixture?
(a) mixtures of acetone and trichloromethane shows positive deviation from Raoult's law
(b) the forces of attraction acting between molecules of acetone and trichloro-methane in a mixture are greater than those acting between the molecules in pure acetone
(c) pure acetone can be obtained by the careful fractional distillation of any mixture of acetone and trichloro-methane
(d) when acetone and trichloro-methane are mixed, the enthalpy change is negative
Solution. Answer: (b), (d). Acetone and chloroform form hydrogen bonds with each other, so the mixture shows negative deviation: A-B attractions are stronger, mixing is exothermic and a maximum-boiling azeotrope forms, so complete separation by fractional distillation is not possible.
Teacher's Note: Acetone-chloroform H-bonding gives negative deviation and a maximum-boiling azeotrope.
Exam Note: Negative deviation example: acetone with chloroform.
One or More Correct, Question 8. The azeotropic solutions of two miscible liquids:
(a) can be separated by simple distillation
(b) may show positive or negative deviation from Raoult's law
(c) are supersaturated solution
(d) behave like a single component and boil at a constant temperature
Solution. Answer: (b), (d). Azeotropes arise from positive deviation (minimum-boiling) or negative deviation (maximum-boiling) and distil unchanged at constant temperature, so they cannot be separated by simple distillation.
Teacher's Note: Azeotrope boils like a pure substance: constant temperature, unchanged composition.
Exam Note: Either type of deviation can give an azeotrope.
One or More Correct, Question 9. For exact determination of molecular mass through colligative properties measurement:
(a) solute must be volatile
(b) solution must be very dilute
(c) solution must be formed by similar nature of substances
(d) solute must not be dissociated or associated
Solution. Answer: (b), (d). The colligative formulae assume a very dilute solution of a non-volatile solute that neither dissociates nor associates; otherwise the van't Hoff factor changes the result.
Teacher's Note: Colligative formulae need ideal dilute solution and i = 1.
Exam Note: Solute must be non-volatile, not volatile.
One or More Correct, Question 10. For the depression of freezing point experiment. The correct statement(s) is/are:
(a) Vapour pressure of pure solvent is more than that of solution
(b) Vapour pressure of pure solvent is less than that of solution
(c) Only solute molecules solidify at the freezing point
(d) Only solvent molecules solidify at the freezing point
Solution. Answer: (a), (d). A non-volatile solute lowers the vapour pressure, so the pure solvent has the higher vapour pressure; at the freezing point only pure solvent separates as solid.
Teacher's Note: Solute lowers vapour pressure; only solvent freezes out.
Exam Note: Freezing out solute is wrong for dilute solutions.
One or More Correct, Question 11. The cryoscopic constant value depends upon:
(a) The molar mass of the solute in the solution
(b) The molar mass of the solvent in the solution
(c) The enthalpy of vaporisation of the solvent
(d) The freezing point of the solvent
Solution. Corrected: (b), (d) (the printed key gives (b), (c), (d)). Kf = MsolventRTf²/(1000ΔHfus), which depends on the solvent's molar mass, its freezing point and its enthalpy of fusion; it does not depend on the solute or on the enthalpy of vaporisation.
Teacher's Note: Kf involves solvent M, Tf and ΔHfus, not ΔHvap.
Exam Note: Cryoscopic uses fusion enthalpy; ebullioscopic uses vaporisation.
One or More Correct, Question 12. Consider 0.1 M solutions of two solutes X and Y. The solute X behaves as univalent electrolyte, while solute Y dimerises in solution. Select correct statement(s) regarding these solutions:
(a) The boiling point of solution of 'X' will be higher than that of 'Y'
(b) The osmotic pressure of solution of 'Y' will be lower than that of 'X'
(c) The freezing point of solution of 'X' will be lower than that of 'Y'
(d) The relative lowering of vapour pressure of both the solution will be the same
Solution. Answer: (a), (b), (c). X has i ≈ 2 and dimerising Y has i < 1, so X has the larger boiling point elevation, osmotic pressure and freezing point depression; relative lowering of vapour pressure differs.
Teacher's Note: i(X) ≈ 2 > 1 > i(Y): all colligative effects are larger for X.
Exam Note: Compare van't Hoff factors, not formulas.
One or More Correct, Question 13. Consider following solutions: (I) 1 M glucose (aq); (II) 1 M sodium chloride (aq); (III) 1 M acetic acid in benzene; (IV) 1 M ammonium phosphate (aq)
(a) all are isotonic solutions
(b) III is hypotonic of I, IV
(c) I, II, IV are hypertonic of III
(d) IV is hypertonic of I, III
Solution. Answer: (b), (c), (d). Acetic acid dimerises in benzene (i < 1), glucose has i = 1, NaCl i = 2 and (NH4)3PO4 i = 4. So π order is IV > II > I > III: III is hypotonic to I and IV; I, II and IV are hypertonic to III; IV is hypertonic to I and III. Not all are isotonic.
Teacher's Note: Rank by i·C: ammonium phosphate highest, acetic acid in benzene lowest.
Exam Note: Hypertonic means higher osmotic pressure.
One or More Correct, Question 14. Which of the following statements is (are) incorrect?
(a) 0.1 M KCl solution will have the same osmotic pressure as 0.1 M glucose solution
(b) 0.1 M KCl solution will have the same boiling point as 0.1 M urea solution
(c) 0.1 m glucose and 0.1 m urea are isotonic
(d) 0.1 m MgCl2 solution will have less relative lowering of vapour pressure than 0.1 m NaCl
Solution. Answer: (a), (b), (d). KCl (i = 2) has twice the osmotic pressure and boiling point elevation of glucose or urea at equal concentration, so (a) and (b) are incorrect. MgCl2 (i = 3) lowers the vapour pressure more than NaCl (i = 2), so (d) is incorrect. Statement (c) is correct.
Teacher's Note: Electrolytes have larger colligative effects than non-electrolytes at same concentration.
Exam Note: Incorrect statements: those equating electrolytes with non-electrolytes.
One or More Correct, Question 15. Consider following solutions: 0.1 m C6H5NH3+Cl−; 0.1 m KCl; 0.1 m Glucose; 0.1 m Na2C2O4·10H2O
(a) the solution with highest boiling point is 0.1 m Na2C2O4·10H2O
(b) the solution with highest freezing point is 0.1 m glucose
(c) 0.1 m C6H5NH3Cl and 0.1 m NaCl will have the same osmotic pressure
(d) 0.1 m glucose solution will have the lowest osmotic pressure
Solution. Answer: (a), (b), (c), (d). Particles per formula unit: Na2C2O4 3, anilinium chloride 2, KCl 2, glucose 1. Highest boiling point goes with 3 ions, highest freezing point and lowest osmotic pressure with glucose, and the two 1:1 salts have equal effects.
Teacher's Note: Count ions per formula unit: 3, 2, 2, 1.
Exam Note: Equal i gives equal colligative effects at equal molality.
Match the Column
Match the Column, Question 1. Match the entries of Column-I with Column-II (one or more entries may match).
Column-I: (A) n-hexane + n-heptane; (B) Acetone + chloroform; (C) Chloro-benzene and bromo-benzene; (D) Ethanol + water.
Column-II: (P) Can be separated by fractional distillation; (Q) Maximum boiling azeotrope; (R) Cannot be separated by fractional distillation completely; (S) Minimum boiling azeotrope.
Solution. Answer: A → P; B → Q, R; C → P; D → R, S. Hexane-heptane and chlorobenzene-bromobenzene are near-ideal pairs and separate completely. Acetone-chloroform forms a maximum-boiling azeotrope (cannot be separated completely); ethanol-water forms a minimum-boiling azeotrope (cannot be separated completely).
Teacher's Note: Ideal pairs separate fully; azeotropes (max or min) do not.
Exam Note: Azeotrope entries match both type and non-separability.
Match the Column, Question 2. Column-I: (A) π1 : 0.1 M glucose; π2 : 0.1 M urea; (B) π1 : 0.1 M NaCl; π2 : 0.1 M Na2SO4; (C) π1 : 0.1 M NaCl; π2 : 0.1 M KCl; (D) π1 : 0.1 M CuSO4; π2 : 0.1 M sucrose.
Column-II: (P) π1 and π2 are isotonic; (Q) No net migration of solvent across the membrane; (R) π1 is hypertonic to π2; (S) π1 is hypotonic to π2.
Solution. Answer: A → P, Q; B → S; C → P, Q; D → R. Glucose/urea (both i = 1) and NaCl/KCl (both i = 2) are isotonic with no net solvent flow. NaCl (0.2) is hypotonic to Na2SO4 (0.3). CuSO4 (0.2) is hypertonic to sucrose (0.1).
Teacher's Note: Compare i·C of each pair to classify isotonic, hypo- or hypertonic.
Exam Note: Equal particle concentration means isotonic and no net flow.
Match the Column, Question 3. Column-I: (A) 0.1 M Al2(SO4)3; (B) 0.1 M AlPO4; (C) 0.1 M urea; (D) 0.1 M MgCl2.
Column-II: (P) Solution with highest boiling point; (Q) Van't Hoff factor is greater than 1; (R) Solution with lowest osmotic pressure; (S) Solution with lowest freezing point.
Solution. Answer: A → P, Q, S; B → Q; C → R; D → Q. Al2(SO4)3 gives 5 ions, the largest effect (highest boiling point, lowest freezing point, i > 1). AlPO4 and MgCl2 are electrolytes with i > 1, and urea (i = 1) has the lowest osmotic pressure.
Teacher's Note: Largest i gives highest b.p. and lowest f.p.; urea gives lowest π.
Exam Note: Only electrolytes have i greater than 1.
Match the Column, Question 4. Column-I (Solute): (A) AlCl3 if α = 0.8; (B) BaCl2 if α = 0.9; (C) Na3PO4 if α = 0.9; (D) K4[Fe(CN)6] if α = 0.7.
Column-II (Van't Hoff factor, i): (P) i = 3.4; (Q) i = 2.8; (R) i = 3.8; (S) i = 3.7.
Solution. Answer: A → P; B → Q; C → S; D → R. i = 1 + (n − 1)α: AlCl3 1 + 3×0.8 = 3.4; BaCl2 1 + 2×0.9 = 2.8; Na3PO4 1 + 3×0.9 = 3.7; K4[Fe(CN)6] 1 + 4×0.7 = 3.8.
Teacher's Note: Apply i = 1 + (n − 1)α with n = number of ions.
Exam Note: n = 4, 3, 4, 5 for the four salts.
Match the Column, Question 5. Column-I: (A) Elevation of B.P.; (B) Osmotic pressure; (C) Relative lowering in V.P.; (D) Depression of F.P.
Column-II: (P) Colligative property; (Q) Ebullioscopic constant; (R) Berkeley-Heartley; (S) Ostwald and Walker method.
Solution. Corrected: A → P, Q; B → P, R; C → P, S; D → P (the printed key gives C → P, R). Relative lowering of vapour pressure is measured by the Ostwald-Walker method, while the Berkeley-Hartley method measures osmotic pressure.
Teacher's Note: Match each property to its measuring method: Ostwald-Walker for vapour pressure.
Exam Note: Berkeley-Hartley is for osmotic pressure only.
Assertion-Reason Type Questions
Assertion-Reason, Question 1. STATEMENT-1: An increase in surface area increases the rate of evaporation.
STATEMENT-2: Stronger the inter-molecular attraction forces, faster is the rate of evaporation at a given temperature.
Options: (A) both true and S2 explains S1; (B) both true, S2 does not explain S1; (C) S1 true, S2 false; (D) S1 false, S2 true.
Solution. Answer: (C). Statement-1 is true: a larger surface exposes more molecules. Statement-2 is false: stronger intermolecular attraction makes evaporation slower.
Teacher's Note: Rate of evaporation grows with area but falls with stronger attraction.
Exam Note: Check each statement separately.
Assertion-Reason, Question 2. STATEMENT-1: An ideal solution obeys Raoult's law.
STATEMENT-2: In an ideal solution, solute-solute as well as solvent-solvent, interactions are similar to solute-solvent interactions.
Solution. Answer: (A). Statement-1 is true and Statement-2 is true; equal A-A, B-B and A-B interactions are the reason why the solution obeys Raoult's law.
Teacher's Note: Equal interactions explain Raoult's law obedience.
Exam Note: Reason must explain, not just be true.
Assertion-Reason, Question 3. STATEMENT-1: If a liquid solute more volatile than the solvent is added to the solvent, the vapour pressure of the solution is greater than vapour pressure of pure solvent.
STATEMENT-2: Vapour pressure of solution is equal to vapour pressure of solvent.
Solution. Answer: (C). Statement-1 is true: the volatile solute adds its own partial pressure. Statement-2 is false.
Teacher's Note: Added volatile solute raises total vapour pressure above pure solvent.
Exam Note: Raoult's law reduction applies to non-volatile solutes only.
Assertion-Reason, Question 4. STATEMENT-1: ΔVmix and ΔSmix for an ideal solution is zero.
STATEMENT-2: A...B interaction in an ideal solution are same as between A...A and B...B.
Solution. Answer: (D). Statement-1 is false: ΔVmix = 0 but ΔSmix > 0. Statement-2 is true.
Teacher's Note: Ideal mixing has zero ΔV and ΔH but positive ΔS.
Exam Note: Entropy of mixing is never zero.
Assertion-Reason, Question 5. STATEMENT-1: Elevation in boiling point will be high if the molal elevation constant of the liquid is high.
STATEMENT-2: Elevation in boiling point is a colligative property.
Solution. Answer: (B). Both statements are true (ΔTb = Kbm), but being colligative does not explain why a high Kb gives a high elevation.
Teacher's Note: ΔTb = Kbm; Kb is a property of the solvent.
Exam Note: Reason is true but not the explanation.
Assertion-Reason, Question 6. STATEMENT-1: The boiling point of 0.1 M urea solution is less than that of 0.1 M KCl solution.
STATEMENT-2: Elevation of boiling point is directly proportional to the number of moles of non-volatile solute particles present in the solution.
Solution. Answer: (A). KCl gives two particles against one for urea, and ΔTb is proportional to the number of particles, so Statement-2 explains Statement-1.
Teacher's Note: KCl gives twice the particles of urea at equal molarity.
Exam Note: Particle count explains the order.
Assertion-Reason, Question 7. STATEMENT-1: The observed molar mass of acetic acid in benzene is more than the normal molar mass of acetic acid.
STATEMENT-2: Molecules of acetic acid dimerise in benzene due to hydrogen bonding.
Solution. Answer: (A). Dimerisation lowers the number of particles, so the observed molar mass is higher; hydrogen bonding is the reason for dimerisation.
Teacher's Note: Association reduces particle count, raising observed molar mass.
Exam Note: Hydrogen bonding causes dimerisation.
Assertion-Reason, Question 8. STATEMENT-1: Addition of ethylene glycol to water lowers the freezing point of water, therefore, used as antifreeze substance.
STATEMENT-2: Ethylene glycol is soluble in water.
Solution. Answer: (B) (from key). Both statements are true; solubility in water is needed but it is the depression of freezing point (a colligative effect) that makes it an antifreeze, so Statement-2 is not the explanation.
Teacher's Note: Antifreeze action is freezing point depression; solubility is only a prerequisite.
Exam Note: Explain via ΔTf = Kfm.
Assertion-Reason, Question 9. STATEMENT-1: Osmotic pressure is a colligative property.
STATEMENT-2: Osmotic pressure developed in a column due to osmosis.
Solution. Answer: (B). Both statements are true, but the reason merely describes how osmotic pressure arises and does not explain why it is colligative (dependence on number of particles).
Teacher's Note: Colligative means dependence on particle number, not on how pressure arises.
Exam Note: Reason is true, no explanation.
Assertion-Reason, Question 10. STATEMENT-1: Osmosis involves movement of solvent molecules from its lower concentration to its higher concentration.
STATEMENT-2: Solutions having the same osmotic pressure are called isotonic solutions.
Solution. Answer: (B). Both statements are true; the definition of isotonic solutions does not explain the direction of solvent flow.
Teacher's Note: Solvent moves from dilute to concentrated; isotonic is just a definition.
Exam Note: Statement-2 is a definition.
Assertion-Reason, Question 11. STATEMENT-1: Isotonic solutions must have the same molar concentration.
STATEMENT-2: Solutions which have the same osmotic pressure are known as isotonic solution.
Solution. Answer: (D). Statement-1 is false: isotonic solutions have equal osmotic pressure, which equals equal molar concentration only when i is the same. Statement-2 is true.
Teacher's Note: Equal π means equal iC, not necessarily equal C.
Exam Note: Isotonic means same π only.
Assertion-Reason, Question 12. STATEMENT-1: Isotonic solutions do not show phenomenon of osmosis.
STATEMENT-2: Isotonic solutions have same molar concentration at same temperature.
Solution. Answer: (A) (from key). Isotonic solutions have equal osmotic pressure (effective concentration), so there is no net osmosis, per the book's key.
Teacher's Note: No net solvent flow between solutions of equal π.
Exam Note: Key treats equal concentration as the reason.
Assertion-Reason, Question 13. STATEMENT-1: When dried fruits and vegetables are placed in water, they slowly get swelled.
STATEMENT-2: It happens due to the phenomenon of osmosis.
Solution. Answer: (A). Water enters the cells through their semipermeable walls by osmosis, so they swell.
Teacher's Note: Water moves into the more concentrated cell contents by osmosis.
Exam Note: Osmosis explains the swelling.
Assertion-Reason, Question 14. STATEMENT-1: Reverse osmosis is used to purify sea water.
STATEMENT-2: Solvent molecules pass from concentrate solution to pure solvent through semipermeable membrane if high pressure is applied on solution side.
Solution. Answer: (B) (from key). Both statements are true; the key treats Statement-2 as a description of the process, not an explanation of why sea water is purified.
Teacher's Note: Applied pressure above π reverses solvent flow.
Exam Note: Key marks reason as not the explanation.
Assertion-Reason, Question 15. STATEMENT-1: All solutes becomes more soluble in water at higher temperature.
STATEMENT-2: Solubility of solute depends upon temperature.
Solution. Answer: (D). Statement-1 is false: solubility of some solutes (for example Ce2(SO4)3 or gases) decreases with temperature. Statement-2 is true.
Teacher's Note: Temperature dependence can be positive or negative.
Exam Note: Not 'all' solutes dissolve more at higher T.
Assertion-Reason, Question 16. STATEMENT-1: Henry's law is always applicable for gases.
STATEMENT-2: Raoult's law is a special case of Henry's law.
Solution. Answer: (D). Statement-1 is false: Henry's law fails at high pressure or when the gas reacts with the solvent. Statement-2 is true (Raoult's law is the case KH = P°).
Teacher's Note: Henry's law holds only for dilute, non-reacting gas solutions.
Exam Note: 'Always' makes statement 1 false.
Assertion-Reason, Question 17. STATEMENT-1: Increasing pressure on pure water decrease its freezing point.
STATEMENT-2: Density of water is maximum at 273 K.
Solution. Answer: (C). Statement-1 is true: ice is less dense than water, so pressure favours the liquid and lowers the freezing point. Statement-2 is false: water's maximum density occurs at 277 K (4°C).
Teacher's Note: Ice floats, so pressure lowers water's freezing point.
Exam Note: Maximum density is at 4°C, not 0°C.
Assertion-Reason, Question 18. STATEMENT-1: The molecular weight of acetic acid determined by depression in freezing point method in benzene and water was found to be different.
STATEMENT-2: Water is polar and benzene is non-polar.
Solution. Answer: (A). In polar water acetic acid ionises (observed mass lower), while in non-polar benzene it dimerises (observed mass higher); the polarity difference explains the different results.
Teacher's Note: Polar solvent ionises acid; non-polar solvent promotes dimerisation.
Exam Note: Solvent polarity changes i.
Assertion-Reason, Question 19. STATEMENT-1: If red blood cells were removed from the body and placed in pure water, pressure inside the cell increases.
STATEMENT-2: The concentration of the salt content in the cells increases.
Solution. Answer: (C). Statement-1 is true: water enters by osmosis and the cell swells. Statement-2 is false: salt concentration decreases as the cell is diluted.
Teacher's Note: Water enters, diluting the salt content.
Exam Note: Concentration falls, not rises.
Assertion-Reason, Question 20. STATEMENT-1: Azeotrope is a binary mixture formed by ideal solutions.
STATEMENT-2: Azeotrope boils with unchanged composition.
Solution. Answer: (D). Statement-1 is false: azeotropes form from non-ideal solutions (positive or negative deviation). Statement-2 is true.
Teacher's Note: Azeotropes need non-ideality; ideal solutions can be separated.
Exam Note: Azeotrope: constant boiling, non-ideal.
Subjective Problems
Subjective Problem 1. The vapour pressure of two pure liquids A and B are 5 and 10 torr respectively. Calculate the total pressure of the solution (in torr) obtained by mixing 2 mole of A and 3 mole of B.
Solution. Answer: 8. xA = 2/5 = 0.4 and xB = 0.6. P = 5×0.4 + 10×0.6 = 2 + 6 = 8 torr.
Teacher's Note: Mole fractions 0.4 and 0.6 then weighted sum.
Exam Note: Use mole fractions, not moles.
Subjective Problem 2. The vapour pressure of two pure liquids A and B are 50 and 40 torr respectively. If 8 moles of A is mixed with x moles of B, then vapour pressure of solution obtained is 48 torr. What is the value of x.
Solution. Answer: 2. 48 = (50×8 + 40x)/(8 + x), so 384 + 48x = 400 + 40x and x = 2.
Teacher's Note: Set up weighted average and solve linear equation.
Exam Note: Show the equation in terms of x.
Subjective Problem 3. The vapour pressure of a liquid solution containing A and B is 99 torr. Calculate mole % of B in vapour phase. (Given: PA° = 100 torr; PB° = 80 torr)
Solution. Answer: 4. 99 = 100xA + 80(1 − xA), so xA = 0.95 and xB = 0.05. yB = 80×0.05/99 = 0.0404, i.e. 4.04 ≈ 4 mole %.
Teacher's Note: Find liquid composition first, then vapour mole fraction of B.
Exam Note: yB = PB/Ptotal.
Subjective Problem 4. If 30 g of a solute of molecular weight 154 is dissolved in 250 g of benzene. What will be the boiling point of the resulting solution? (Given: Kb(C6H6) = 2.6 K kg mol-1)
Solution. Answer: 2 (the elevation in boiling point, in K). m = (30/154)/0.250 = 0.779 mol/kg; ΔTb = 2.6×0.779 = 2.03 ≈ 2 K. (The normal boiling point of benzene is not given, so the printed answer is the elevation.)
Teacher's Note: Molality from grams and kg of solvent, then Kbm.
Exam Note: Final answer is the elevation ΔTb.
Subjective Problem 5. Calculate elevation in boiling point for 2 molal aqueous solution of glucose. (Given: Kb(H2O) = 0.5 K kg mol-1)
Solution. Answer: 1. ΔTb = Kbm = 0.5×2 = 1 K.
Teacher's Note: Non-electrolyte so i = 1: ΔTb = Kbm.
Exam Note: One line: Kb×m.
Subjective Problem 6. Calculate depression of freezing point for 0.56 molal aq. solution of KCl. (Given: Kf(H2O) = 1.8 K kg mol-1).
Solution. Answer: 2. KCl gives i = 2: ΔTf = 2×1.8×0.56 = 2.016 ≈ 2 K.
Teacher's Note: KCl is an electrolyte: multiply by i = 2.
Exam Note: Do not forget van't Hoff factor.
Subjective Problem 7. What is the maximum value of van't Hoff factor for AlCl3?
Solution. Answer: 4. Complete dissociation AlCl3 → Al3+ + 3Cl− gives 4 ions, so imax = 4.
Teacher's Note: Maximum i equals the number of ions on complete dissociation.
Exam Note: Count ions in the formula.
Subjective Problem 8. A solution containing 500 g of a protein per litre is isotonic with a solution containing 3.42 g sucrose per litre. The molecular mass of protein in 5 × 10x, hence x is.
Solution. Answer: 4. Isotonic solutions have equal molarity: 500/M = 3.42/342, so M = 5×104 and x = 4.
Teacher's Note: Equal molarity gives M = 500 × 342/3.42.
Exam Note: Write M as 5×104.
Subjective Problem 9. An aqueous solution of urea has a freezing point of −0.515°C. Predict the osmotic pressure (in atm) of the same solution at 37°C. (Given: Kf(H2O) = 1.86 K kg mol-1)
Solution. Answer: 7. m = 0.515/1.86 = 0.277; taking molarity ≈ molality, π = CRT = 0.277×0.0821×310 = 7.05 ≈ 7 atm.
Teacher's Note: Molality from ΔTf, then π = CRT at 310 K.
Exam Note: Convert 37°C to 310 K.
Subjective Problem 10. 0.2 M aq. solution of KCl is isotonic with 0.2 M K2SO4 at same temperature. What is the van't Hoff factor of K2SO4?
Solution. Answer: 2. Isotonic solutions have equal iC. With equal molarity the van't Hoff factors must be equal, so i(K2SO4) = i(KCl) = 2 (taking KCl as completely ionised).
Teacher's Note: Equal π and equal C imply equal i.
Exam Note: Equal concentration so i must match.
JEE Mathematics: Narendra Awasthi Solutions for Narendra Awasthi Solutions Physical Chemistry Chapter 9 Dilute Solution
Complete Math Solutions for Narendra Awasthi Solutions Physical Chemistry Chapter 9 Dilute Solution
Access the complete chapter-wise PDF for Narendra Awasthi Solutions Physical Chemistry Chapter 9 Dilute Solution. These structured Narendra Awasthi Solutions solutions for JEE Mathematics help students build foundational accuracy and prepare effectively for upcoming school evaluations.
Mastering Core Concepts with Narendra Awasthi Solutions
Clear, methodical explanations accompany every challenging problem within the text. Engaging with these detailed mathematical breakdowns lays a solid foundation for advanced learning and improves execution speed for upcoming exams.
Additional Study Materials for 2026
Maximize your academic readiness by pairing these solutions with our official sample papers and interactive practice tests. All supplementary study materials for the 2026 session are available across our platform free of charge.
FAQs
They are chapter-wise solved questions from the Narendra Awasthi book for JEE Chemistry. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.