Official IE Irodov Textbook Solutions: JEE Physics Chapter 18 Electric Capacitance Energy Of An Electric Field
Access comprehensive textbook solutions for Chapter 18 Electric Capacitance Energy Of An Electric Field using the IE Irodov reference material for JEE Physics. Designed to align with the 2026 academic curriculum, these detailed answers help students reinforce core academic concepts and master complex problem-solving methods.
Chapter-wise Solutions for Physics: Chapter 18 Electric Capacitance Energy Of An Electric Field
Navigate directly to the solved Physics textbook exercises using the digital viewer below. Each solution includes detailed step-by-step explanations, allowing students to instantly cross-check their work and identify areas requiring further revision.
Electric Capacitance. Energy of an Electric Field - Problems 101-146
Question 101. Find the capacitance of an isolated ball-shaped conductor of radius R1 surrounded by an adjacent concentric layer of dielectric with permittivity ε and outside radius R2.
Solution.
Let us mentally impart a charge q on the conductor. Then the potential difference between the conductor and infinity is
φ+ − φ− = ∫R1R2 q/(4πε0ε r²) dr + ∫R2∞ q/(4πε0 r²) dr
= q/(4πε0ε) [1/R1 − 1/R2] + q/(4πε0) · 1/R2
= q/(4πε0ε) [(ε − 1)/R2 + 1/R1]
Hence the sought capacitance,
C = q/(φ+ − φ−) = 4πε0ε / [(ε − 1)/R2 + 1/R1] = 4πε0ε R1 / [(ε − 1)(R1/R2) + 1]
Teacher's Note: Add the potential drops across dielectric (field reduced by ε) and across vacuum outside R2.
Exam Note: Check limits: ε = 1 gives 4πε0R1.
Question 102. Two parallel-plate air capacitors, each of capacitance C, were connected in series to a battery with emf ξ. Then one of the capacitors was filled up with uniform dielectric with permittivity ε. How many times did the electric field strength in that capacitor decrease? What amount of charge flows through the battery?
Solution.
From the symmetry of the problem, the voltage across each capacitor is Δφ = ξ/2 and the charge on each capacitor is q = Cξ/2 in the absence of dielectric. Now when the dielectric is filled up in one of the capacitors, the equivalent capacitance of the system is
C′0 = Cε/(1 + ε)
The potential difference across the capacitor which is filled with dielectric is
Δφ′ = q′/(εC) = [Cε/(1 + ε)] · ξ/(Cε) = ξ/(1 + ε)
But φ ∝ E. So, as φ decreases (1 + ε)/2 times, the field strength also decreases by the same factor, and the flow of charge is
Δq = q′ − q = Cεξ/(1 + ε) − Cξ/2 = ½ Cξ (ε − 1)/(ε + 1)
Teacher's Note: Series capacitors carry equal charge; E = V/d in the filled capacitor, with the new voltage ξ/(1+ε).
Exam Note: Answer: E falls (ε+1)/2 times; Δq = ½Cξ(ε−1)/(ε+1).
Question 103. The space between the plates of a parallel-plate capacitor is filled consecutively with two dielectric layers 1 and 2 having the thicknesses d1 and d2 and the permittivities ε1 and ε2 respectively. The area of each plate is equal to S. Find: (a) the capacitance of the capacitor; (b) the density σ′ of the bound charges on the boundary plane if the voltage across the capacitor equals V and the electric field is directed from layer 1 to layer 2.
Solution.
(a) As it is a series combination of two capacitors,
1/C = d1/(ε0ε1S) + d2/(ε0ε2S), or C = ε0S / [(d1/ε1) + (d2/ε2)]
(b) Let σ be the initial (free) surface charge density; then the density of bound charge on the boundary plane is
σ′ = σ(1 − 1/ε1) − σ(1 − 1/ε2) = σ(1/ε2 − 1/ε1)
But σ = q/S = CV/S = ε0ε1ε2V / (ε2d1 + ε1d2)
So, σ′ = ε0V(ε1 − ε2) / (ε2d1 + ε1d2)
Teacher's Note: Bound charge on each face is σ(1 − 1/ε); the boundary plane carries the difference of the two faces.
Exam Note: Write series formula first; then σ = CV/S.
Question 104. The gap between the plates of a parallel-plate capacitor is filled with isotropic dielectric whose permittivity ε varies linearly from ε1 to ε2 (ε2 > ε1) in the direction perpendicular to the plates. The area of each plate equals S, the separation between the plates is equal to d. Find: (a) the capacitance of the capacitor; (b) the space density of the bound charges as a function of ε if the charge of the capacitor is q and the field E in it is directed toward the growing ε values.
Solution.
(a) We point the x-axis towards the right and place the origin on the left-hand plate. The left plate is assumed to be positively charged. Since ε varies linearly, we can write ε(x) = a + bx, where a and b are determined from the boundary conditions ε = ε1 at x = 0 and ε = ε2 at x = d. Thus
ε(x) = ε1 + [(ε2 − ε1)/d] x
The potential difference between the plates is
φ+ − φ− = ∫0d E dx = ∫0d σ/(ε0ε(x)) dx = ∫0d σ dx / {ε0[ε1 + ((ε2 − ε1)/d) x]} = [σd/((ε2 − ε1)ε0)] ln(ε2/ε1)
Hence the sought capacitance
C = σS/(φ+ − φ−) = (ε2 − ε1)ε0S / [d ln(ε2/ε1)]
(b) D = q/S and P = q/S − q/(Sε(x)). The space density of bound charges is
ρ′ = −div P = −q(ε2 − ε1) / (S d ε²(x))
Teacher's Note: Integrate dx/ε(x) for the voltage; bound charge density is −div P with P = D(1 − 1/ε).
Exam Note: Answer (b) needs dε/dx = (ε2−ε1)/d.
Question 105. Find the capacitance of a spherical capacitor whose electrodes have radii R1 and R2 > R1 and which is filled with isotropic dielectric whose permittivity varies as ε = a/r, where a is a constant, and r is the distance from the centre of the capacitor.
Solution.
Let us mentally impart a charge q to the conductor. Now the potential difference between the plates is
φ+ − φ− = ∫R1R2 E dr = ∫R1R2 q/(4πε0a/r) · (1/r²) dr = [q/(4πε0a)] ln(R2/R1)
Hence the sought capacitance,
C = q/(φ+ − φ−) = 4πε0a / ln(R2/R1)
Teacher's Note: E = q/(4πε0εr²) simplifies to q/(4πε0a r), giving a logarithm.
Exam Note: Substitute ε = a/r before integrating.
Question 106. A cylindrical capacitor is filled with two cylindrical layers of dielectric with permittivities ε1 and ε2. The inside radii of the layers are equal to R1 and R2 > R1. The maximum permissible values of electric field strength are equal to E1m and E2m for these dielectrics. At what relationship between ε, R, and Em will the voltage increase result in the field strength reaching the breakdown value for both dielectrics simultaneously?
Solution.
Let λ be the linear charge density. Then the maximum field in each layer occurs at its inner radius:
E1m = λ/(2πε0R1ε1) (1)
and E2m = λ/(2πε0R2ε2) (2)
The breakdown in either case occurs at the smallest value of r in the layer (the inner surface). For simultaneous breakdown of both dielectrics, from (1) and (2) we get
E1mR1ε1 = E2mR2ε2,
which is the sought relationship.
Teacher's Note: Field in a cylindrical layer is largest at its inner radius; equate λ/2πε0 from both layers.
Exam Note: State EmRε equality.
Question 107. There is a double-layer cylindrical capacitor whose parameters are shown in the figure (inner radius R1, layer 1 with ε1 between R1 and R2, layer 2 with ε2 between R2 and R3). The breakdown field strength values for these dielectrics are equal to E1 and E2 respectively. What is the breakdown voltage of this capacitor if ε1R1E1 < ε2R2E2?
Solution.
Let λ be the linear charge density. Then the sought potential difference is
φ+ − φ− = ∫R1R2 λ/(2πε0ε1r) dr + ∫R2R3 λ/(2πε0ε2r) dr = [λ/(2πε0)] [ (1/ε1) ln(R2/R1) + (1/ε2) ln(R3/R2) ]
Now, as ε1R1E1 < ε2R2E2, the value λ/(2πε0) = E1R1ε1 is the maximum acceptable value, and for values greater than E1R1ε1 dielectric breakdown will take place (first in layer 1).
Hence the maximum potential difference between the plates is
φ+ − φ− = E1R1ε1 [ (1/ε1) ln(R2/R1) + (1/ε2) ln(R3/R2) ] = E1R1 [ ln(R2/R1) + (ε1/ε2) ln(R3/R2) ]
Teacher's Note: The layer that reaches its limit first fixes λ; then sum the two logarithmic potential drops.
Exam Note: Identify which layer breaks down first.
Question 108. Two long straight wires with equal cross-sectional radii a are located parallel to each other in air. The distance between their axes equals b. Find the mutual capacitance of the wires per unit length under the condition b ≫ a.
Solution.
Let the linear charge density of the wires be λ. The potential difference is φ+ − φ− = φ − (−φ) = 2φ. The intensity of the electric field created by one of the wires at a distance x from its axis can be easily found with the help of Gauss's theorem, E = λ/(2πε0x). Then
φ = ∫ab−a E dx = [λ/(2πε0)] ln[(b − a)/a] ≈ [λ/(2πε0)] ln(b/a) (b ≫ a)
Hence the capacitance per unit length is
λ/(φ+ − φ−) = λ/(2φ) = πε0 / ln(b/a)
Corrected: the book prints 2πε0/ln(b/a), which does not follow from its own working (φ+ − φ− = 2φ). The correct value is πε0/ln(b/a).
Teacher's Note: Each wire contributes φ; the pair voltage is 2φ, which halves the capacitance per length.
Exam Note: Do not drop the factor 2 in 2φ.
Question 109. A long straight wire is located parallel to an infinite conducting plate. The wire cross-sectional radius is equal to a, the distance between the axis of the wire and the plane equals b. Find the mutual capacitance of this system per unit length of the wire under the condition a ≪ b.
Solution.
The field in the region between the conducting plane and the wire can be obtained by using an oppositely charged wire as an image on the other side (at distance b behind the plane). Then the potential difference between the wire and the plane is
Δφ = ∫ab [λ/(2πε0r) + λ/(2πε0(2b − r))] dr = [λ/(2πε0)] ln(b/a) + [λ/(2πε0)] ln[(2b − a)/b] = [λ/(2πε0)] ln[(2b − a)/a] ≈ [λ/(2πε0)] ln(2b/a) (b ≫ a)
Hence the sought mutual capacitance of the system per unit length of the wire
= λ/Δφ = 2πε0 / ln(2b/a)
Teacher's Note: Method of images: replace the plane by an opposite line charge at distance 2b.
Exam Note: Integrate the fields of wire and image from a to b.
Question 110. Find the capacitance of a system of two identical metal balls of radius a if the distance between their centres is equal to b, with b ≫ a. The system is located in a uniform dielectric with permittivity ε.
Solution.
When b ≫ a, the charge distribution on each spherical conductor is practically unaffected by the presence of the other conductor. Then the potential φ+ (φ−) on the positively (respectively negatively) charged conductor is +q/(4πε0εa) (−q/(4πε0εa)).
Thus φ+ − φ− = q/(2πε0εa) and
C = q/(φ+ − φ−) = 2πε0εa.
Note: if we require terms which depend on a/b, we have to take account of the distribution of charge on the conductors.
Teacher's Note: Far apart, each ball's potential ignores the other; the two potentials differ by 2q/(4πε0εa).
Exam Note: Voltage is twice a single ball's potential.
Question 111. Determine the capacitance of a system consisting of a metal ball of radius a and an infinite conducting plane separated from the centre of the ball by the distance l if l ≫ a.
Solution.
As in Q.109 we apply the method of images. Then the potential difference between the positively charged sphere and the conducting plane is one half the nominal potential difference between the sphere and its image, and is
Δφ = ½(φ+ − φ−) = q/(4πε0a)
Thus C = q/Δφ = 4πε0a, for l ≫ a.
Teacher's Note: Image charge −q at distance 2l; the plane sits at half the sphere–image potential difference.
Exam Note: Result equals the isolated-ball capacitance.
Question 112. Find the capacitance of a system of identical capacitors between points A and B shown in (a) the first figure (three capacitors C1, C2, C3 connected as drawn); (b) the second figure (five identical capacitors C).
Solution.
(a) The potentials satisfy φ1 = φB and φ2 = φA (the nodes joined by the wires), so the three capacitors C1, C2, C3 are all connected directly between A and B, i.e. in parallel. Hence the capacitance between A and B is
C = C1 + C2 + C3
(b) The arrangement is equivalent to a bridge: capacitors C from A to D, D to B, A to E, E to B, and a fifth capacitor C between D and E. From the symmetry of the problem, there is no potential difference between D and E, so the middle capacitor carries no charge and the combination reduces to two series branches, each of capacitance C/2, in parallel. Hence the net capacitance
C0 = C/2 + C/2 = C
(Figures not redrawn; described in words.)
Teacher's Note: Label equal-potential nodes first; a balanced bridge's middle capacitor carries no charge.
Exam Note: Redraw circuit with equal-potential nodes merged.
Question 113. Four identical metal plates are located in air at equal distances d from one another. The area of each plate is equal to S. Find the capacitance of the system between points A and B if the plates are interconnected as shown (a) in the first figure (plates 1 and 3 joined to one terminal side, as drawn); (b) in the second figure.
Solution.
(a) In the given arrangement, we have three capacitors of equal capacitance C = ε0S/d, and the first and third plates are at the same potential. Hence we can resolve the network into a simple form using series and parallel grouping: two capacitors C in parallel, in series with a third capacitor C. Thus the equivalent capacitance
C0 = (C + C)C / [(C + C) + C] = (2/3) C = 2ε0S/(3d)
(b) Let us mentally impart the charges +q and −q to the plates 1 and 2 and then distribute them to the other plates using charge conservation and electric induction. As the potential difference between plates 1 and 2 is zero, with q1 and q2 the charges on the capacitor gaps (C = ε0S/d),
−q1/C + q2/C − q1/C = 0, or q2 = 2q1.
The potential difference between A and B is φ = φA − φB = q2/C. Hence the sought capacitance
C0 = q/φ = (q1 + q2)/(q2/C) = 3q1/(2q1/C) = (3/2) C = 3ε0S/(2d)
(Figures not redrawn.)
Teacher's Note: Three equal gaps; identify equal-potential plates, then use series-parallel or charge conservation.
Exam Note: (a) 2C/3 and (b) 3C/2 with C = ε0S/d.
Question 114. A capacitor of capacitance C1 = 1.0 μF withstands the maximum voltage V1 = 6.0 kV while a capacitor of capacitance C2 = 2.0 μF, the maximum voltage V2 = 4.0 kV. What voltage will the system of these two capacitors withstand if they are connected in series?
Solution.
The maximum charge that the capacitor C1 can withstand is q1 = C1V1, and similarly for C2, q2 = C2V2. But in a series combination the charge on both capacitors is the same, so the maximum charge the combination can withstand is qmax = C1V1, as C1V1 < C2V2 from the numerical data.
The net capacitance of the system is C0 = C1C2/(C1 + C2), and hence
Vmax = qmax/C0 = C1V1 / [C1C2/(C1 + C2)] = V1(1 + C1/C2) = 9 kV
Teacher's Note: In series the same charge flows; the smaller C·V (6 mC vs 8 mC) limits the pair.
Exam Note: Compare C·V, not V, to find the limit.
Question 115. Find the potential difference between points A and B of the system shown in the figure (a source of emf ξ = 110 V feeding a ladder: series C1, shunt C2, series C1, shunt C2, with A and B across the last C2) if the capacitance ratio C2/C1 = η = 2.0.
Solution.
Let us distribute the charges as shown in the figure: q1 on the first C1, q2 on the second C1, (q1 + q2) on the first C2, and q2 on the last C2 (across A, B).
In a closed circuit Σ Δφ = 0. So in the loop DCFED,
q1/C1 − q2/C1 − q2/C2 = ξ, or q1 = C1[ξ + q2(1/C1 + 1/C2)] (1)
Again in the loop DGHED,
q1/C1 + (q1 + q2)/C2 = ξ (2)
Using Eqs. (1) and (2) we get q2[1/C1 + 3/C2 + C1/C22] = −ξC1/C2, so
φA − φB = −q2/C2 = ξ / (C22/C12 + 3C2/C1 + 1) = ξ/(η2 + 3η + 1) = 110/(4 + 6 + 1) = 10 V
Teacher's Note: Write loop equations with charges on each capacitor; or reduce the ladder from the far end.
Exam Note: Answer ξ/(η²+3η+1) = 10 V.
Question 116. Find the capacitance of an infinite circuit formed by the repetition of the same link consisting of two identical capacitors, each with capacitance C (series capacitor C followed by a shunt capacitor C, repeated indefinitely).
Solution.
The infinite circuit may be reduced to the circuit consisting of one link (series C, shunt C) followed by C0, where C0 is the net capacitance of the whole combination (adding one more link to an infinite chain does not change it). So the shunt C is in parallel with C0, and this is in series with C:
1/(C + C0) + 1/C = 1/C0
Solving the quadratic, CC0 + C02 − C2 = 0, we get
C0 = [(√5 − 1)/2] C ≈ 0.62 C,
taking only the positive value as C0 cannot be negative.
Teacher's Note: Self-similarity: adding a link leaves C0 unchanged, giving a quadratic.
Exam Note: Reject the negative root explicitly.
Question 117. A circuit has a section AB shown in the figure (capacitor C1, then a source of emf ξ, then capacitor C2, in series). The emf of the source equals ξ = 10 V, the capacitor capacitances are equal to C1 = 1.0 μF and C2 = 2.0 μF, and the potential difference φA − φB = 5.0 V. Find the voltage across each capacitor.
Solution.
Let us make the charge distribution as shown in the figure (charge q on each capacitor, as they are in series with the source). Now
φA − φB = q/C1 − ξ + q/C2, or q = [(φA − φB) + ξ] C1C2/(C1 + C2)
Hence the voltage across the capacitor C1 is
q/C1 = {[(φA − φB) + ξ]/(C1 + C2)} C2 = 10 V
And the voltage across the capacitor C2 is
q/C2 = {[(φA − φB) + ξ]/(C1 + C2)} C1 = 5 V
Teacher's Note: Treat the source sign carefully: the capacitors share the total (φA−φB)+ξ inversely to C.
Exam Note: Check: 10 V + 5 V − 10 V = 5 V.
Question 118. In a circuit shown in the figure (a loop containing capacitor C1 on top, capacitor C2 at the bottom, source ξ1 on the left and source ξ2 on the right) find the potential difference between the left and right plates of each capacitor.
Solution.
Let ξ2 > ξ1, then using ΣΔφ = 0 in the closed circuit,
−q/C1 + ξ2 − q/C2 − ξ1 = 0, or q = (ξ2 − ξ1)C1C2/(C1 + C2)
Hence the potential difference across the left and right plates of the capacitors is
φ1 = q/C1 = (ξ2 − ξ1)C2/(C1 + C2)
and similarly
φ2 = −q/C2 = (ξ1 − ξ2)C1/(C1 + C2)
Teacher's Note: A single loop of capacitors and sources: same charge on both capacitors, voltages split inversely to C.
Exam Note: Signs follow the left-to-right plate convention.
Question 119. Find the charge of each capacitor in the circuit shown in the previous problem (loop with C1, C2, ξ1, ξ2).
Solution.
Taking the benefit of the foregoing problem, the amount of charge on each capacitor is
|q| = |ξ2 − ξ1| C1C2/(C1 + C2)
Teacher's Note: The two capacitors are in series in one loop, so the net emf is |ξ2 − ξ1|.
Exam Note: Net emf times series capacitance.
Question 120. Determine the potential difference φA − φB between points A and B of the circuit shown in the figure (capacitors C1, C2 in series forming one branch with A between them, C3, C4 in series forming a second branch with B between them, both branches connected across a source ξ). Under what condition is it equal to zero?
Solution.
Make the charge distribution as shown in the figure. In the circuit 12561, ΣΔφ = 0 yields
q1/C4 + q1/C3 − ξ = 0, or q1 = ξC3C4/(C3 + C4)
And in the circuit 13461,
q2/C2 + q2/C1 − ξ = 0, or q2 = ξC1C2/(C1 + C2)
Now
φA − φB = q2/C1 − q1/C3 = ξ[C2/(C1 + C2) − C4/(C3 + C4)] = ξ(C2C3 − C1C4) / [(C1 + C2)(C3 + C4)]
It becomes zero when C2C3 − C1C4 = 0, or C1/C2 = C3/C4.
(Figure not redrawn.)
Teacher's Note: Each branch is a capacitive divider; φA−φB is the difference of the two divider outputs.
Exam Note: Zero condition is the bridge-balance ratio C1/C2 = C3/C4.
Question 121. A capacitor of capacitance C1 = 1.0 μF charged up to a voltage V = 110 V is connected in parallel to the terminals of a circuit consisting of two uncharged capacitors connected in series and possessing the capacitances C2 = 2.0 μF and C3 = 3.0 μF. What charge will flow through the connecting wires?
Solution.
Let the charge q flow through the connecting wires. Then at equilibrium C1 holds charge (C1V − q), and C2, C3 each hold q. In the closed circuit 12341, using ΣΔφ = 0,
−(C1V − q)/C1 + q/C2 + q/C3 = 0
or q = V / (1/C1 + 1/C2 + 1/C3) = 110 / (1 + 0.5 + 0.333) μC = 60 μC = 0.06 mC
Teacher's Note: After connection all three share one loop: the voltage drops of C2, C3 equal that of C1.
Exam Note: Check: 110 V / 1.833 MΩ-equivalent = 60 μC.
Question 122. What charges will flow after the shorting of the switch Sw in the circuit illustrated in the figure (two batteries of emf ξ, capacitor C1 in series along the top, capacitor C2 as a shunt, switch in series with the left battery) through sections 1 and 2 in the directions indicated by the arrows?
Solution.
Initially (switch open) the charge on the capacitors C1 and C2 is, as they are in series with the right battery,
q = ξC1C2/(C1 + C2)
When the switch is closed, in the circuit CDEFC, ΣΔφ = 0 gives
ξ − q2/C2 = 0, or q2 = C2ξ (1)
And in the closed loop BCFAB, ΣΔφ = 0 gives
−q1/C1 + q2/C2 − ξ = 0 (2)
From (1) and (2), q1 = 0.
Now the charge flown through section 1 is (q1 + q2) − 0 = C2ξ, and the charge flown through section 2 is −q1 − q = −ξC1C2/(C1 + C2).
(Figure not redrawn.)
Teacher's Note: After closing, C1 sees zero net emf so its charge vanishes; track each section by charge conservation.
Exam Note: Negative sign means flow opposite to the arrow.
Question 123. In the circuit shown in the figure the emf of each battery is equal to ξ = 60 V, and the capacitor capacitances are equal to C1 = 2.0 μF and C2 = 3.0 μF. Find the charges which will flow after the shorting of the switch Sw through sections 1, 2 and 3 in the directions indicated by the arrows.
Solution.
When the switch is open, the two capacitors are in series across the two batteries (2ξ), so each has charge
q0 = 2ξC1C2/(C1 + C2)
When the switch is closed, each capacitor is connected directly across one battery: q1 = ξC1 and q2 = ξC2.
Hence the flow of charge due to shorting the switch is:
Through section 1: q1 − q0 = ξC1(C1 − C2)/(C1 + C2) = −24 μC
Through section 2: q2 − q0 (change of the charge on the lower plate of C2, with the sign taken in the direction of the arrow) = ξC2(C1 − C2)/(C1 + C2) = −36 μC
Through section 3 (the switch wire, which delivers to the middle node the net change −ξC1 + ξC2): ξ(C2 − C1) = +60 μC
Corrected: the book prints −60 μC for section 3, but the sign is positive; this is the only value consistent with charge conservation (−24 − 36 + 60 = 0) and agrees with ξ(C2 − C1) = 60 × 1 μC.
(Figures not redrawn.)
Teacher's Note: Compare charges before and after closing; the three section flows must sum to zero.
Exam Note: Check signs: flows sum to zero.
Question 124. Find the potential difference φA − φB between points A and B of the circuit shown in the figure (two branches C1–ξ1 and C2–ξ2 in a loop, with C3 connecting A, between C1 and C2, to B, between the two batteries).
Solution.
First of all, make the charge distribution as shown in the figure (q1 on C1, q2 on C2, q1 − q2 on C3). In the loop 12341, using ΣΔφ = 0,
q1/C1 − ξ1 + (q1 − q2)/C3 = 0 (1)
Similarly, in the loop 61456,
q2/C2 + (q2 − q1)/C3 − ξ2 = 0 (2)
From (1) and (2) we have
q2 − q1 = (ξ2C2 − ξ1C1) / (C2/C3 + C1/C3 + 1)
Hence
φA − φB = (q2 − q1)/C3 = (ξ2C2 − ξ1C1) / (C1 + C2 + C3)
(Figure not redrawn.)
Teacher's Note: Two loop equations with charges q1, q2 on the outer capacitors and q1−q2 on C3.
Exam Note: Express answer via C3's charge: φA−φB = (q2−q1)/C3.
Question 125. Determine the potential at point 1 of the circuit shown in the figure (three parallel branches, each a battery ξi in series with a capacitor Ci, i = 1, 2, 3, with points 1, 2, 3 between battery and capacitor and common point O at the capacitor ends), assuming the potential at the point O to be equal to zero. Using the symmetry of the formula obtained, write the expressions for the potentials at points 2 and 3.
Solution.
Let q1, q2 be the charges on C3 and C2 as in the figure, so that C1 holds q1 + q2 with opposite orientation. In the loop ABDEA, using ΣΔφ = 0,
−ξ3 + q1/C3 + (q1 + q2)/C1 + ξ1 = 0 (1)
Similarly in the loop ODEFO,
(q1 + q2)/C1 + ξ1 − ξ2 + q2/C2 = 0 (2)
Solving (1) and (2), we get
q1 + q2 = (ξ2C2 − ξ1C2 − ξ1C3 + ξ3C3) / (C3/C1 + C2/C1 + 1)
Now φ1 − φO = φ1 = −(q1 + q2)/C1 (as φO = 0)
φ1 = [ξ1(C2 + C3) − ξ2C2 − ξ3C3] / (C1 + C2 + C3)
And using the symmetry of the formula,
φ2 = [ξ2(C1 + C3) − ξ1C1 − ξ3C3] / (C1 + C2 + C3)
φ3 = [ξ3(C1 + C2) − ξ1C1 − ξ2C2] / (C1 + C2 + C3)
Note: the polarity of the batteries in the figure (the longer plate of each battery is on the side of points 1, 2, 3) gives these signs; the opposite sign printed in some answer keys corresponds to reversed batteries.
(Figure not redrawn.)
Teacher's Note: Charge on the isolated O-plates sums to zero: ΣCiφi = 0 fixes the common node.
Exam Note: Use symmetry for φ2, φ3; check sign with battery polarity.
Question 126. Find the capacitance of the circuit shown in the figure between points A and B (upper branch C1, C2 in series, lower branch C2, C1 in series, and C3 bridging the two middle points).
Solution.
Taking the advantage of symmetry of the problem, the charge distribution may be made as shown in the figure (upper branch: q1 on C1 and q2 on C2; lower branch: q2 on C2 and q1 on C1; q1 − q2 on C3). In the loop 12561, ΣΔφ = 0:
q2/C2 + (q2 − q1)/C3 − q1/C1 = 0, or q1/q2 = C1(C3 + C2) / [C2(C1 + C3)] (1)
Now the capacitance of the network is
C0 = (q1 + q2)/(φA − φB) = (q1 + q2)/(q2/C2 + q1/C1) = (1 + q1/q2) / (1/C2 + q1/(q2C1)) (2)
From (1) and (2),
C0 = [2C1C2 + C3(C1 + C2)] / (C1 + C2 + 2C3)
(Figure not redrawn.)
Teacher's Note: Use the circuit's central symmetry to reduce unknowns to two charges; C3 carries their difference.
Exam Note: Check: C1=C2 gives C1, independent of C3.
Question 127. Determine the interaction energy of the point charges located at the corners of a square with the side a in the circuits shown in the figure: (a) +q at all four corners; (b) +q, −q, +q, −q alternately around the square (like charges on one diagonal); (c) +q at the two top corners and −q at the two bottom corners.
Solution.
The interaction energy of any two point charges q1 and q2 is given by q1q2/(4πε0r), where r is the separation between the charges. A square has four sides (separation a) and two diagonals (separation √2 a). Hence the interaction energy of the system is:
(a) Ua = 4 q²/(4πε0a) + 2 q²/(4πε0√2 a) = (4 + √2) q²/(4πε0a)
(b) Ub = 4(−q²)/(4πε0a) + 2 q²/(4πε0√2 a) = (−4 + √2) q²/(4πε0a)
(c) Uc = 2 q²/(4πε0a) − 2 q²/(4πε0a) − 2 q²/(4πε0√2 a) = −√2 q²/(4πε0a)
(Figures not redrawn; arrangements described in the question.)
Teacher's Note: Sum qiqj/4πε0r over all six pairs: 4 sides, 2 diagonals, with signs.
Exam Note: Count unlike pairs as negative terms.
Question 128. There is an infinite straight chain of alternating charges q and −q. The distance between the neighbouring charges is equal to a. Find the interaction energy of each charge with all the others. Instruction: make use of the expansion of ln(1 + α) in a power series in α.
Solution.
As the chain is of infinite length, any two charges of the same sign occur symmetrically to any other charge of opposite sign. So the interaction energy of each charge with all the others is
U = −2 · q²/(4πε0a) [1 − 1/2 + 1/3 − 1/4 + … up to ∞] (1)
But ln(1 + x) = x − x²/2 + x³/3 − … up to ∞, and putting x = 1 we get ln 2 = 1 − 1/2 + 1/3 − … up to ∞ (2)
From (1) and (2),
U = −2q² ln 2 / (4πε0a)
Teacher's Note: Each charge has two neighbours at distance na on both sides, giving an alternating series equal to ln 2.
Exam Note: Factor 2 is for the two sides of the chain.
Question 129. A point charge q is located at a distance l from an infinite conducting plane. Find the interaction energy of that charge with those induced on the plane.
Solution.
Using the electrical image method, the force on q is that of an image charge −q at distance 2l, F = q²/(4πε0(2l)²) = q²/(16πε0l²). The interaction energy of the charge with the charges induced on the plane equals the work needed to remove q to infinity against this force:
U = −∫l∞ q²/(16πε0x²) dx = −q²/(16πε0l)
Corrected: the book prints U = −q²/(4πε0(2l)) = −q²/(8πε0l), which is the energy of the real charge and its image treated as an isolated pair; the induced charges are not independent, so the energy of the actual system is half of this, −q²/(16πε0l).
Teacher's Note: Image charges are not real: integrate the force q²/16πε0x² from l to ∞, not use the pair energy.
Exam Note: Energy is half the image-pair energy.
Question 130. Calculate the interaction energy of two balls whose charges q1 and q2 are spherically symmetrical. The distance between the centres of the balls is equal to l. Instruction: start with finding the interaction energy of a ball and a thin spherical layer.
Solution.
Consider the interaction energy of one of the balls (say 1) and a thin spherical shell of the other (ball 2, shell of radius r and charge dQ = ρ2(r) 2πr² sinθ dθ dr, with R the distance from the centre of ball 1). This interaction energy can be written as ∫φ dq
= ∫ [q1/(4πε0R)] ρ2(r) 2πr² sinθ dθ dr = ∫0π ρ2(r) q1 r² sinθ dθ dr / [2ε0(l² + r² + 2lr cosθ)1/2]
= [q1r/(2ε0l)] ρ2(r) dr ∫l−rl+r dx = [q1r/(2ε0l)] ρ2(r) dr · 2r (putting x = (l² + r² + 2lr cosθ)1/2)
= [q1/(4πε0l)] 4πr² dr ρ2(r)
Hence finally, integrating over all shells of ball 2,
Uint = q1q2/(4πε0l), where q2 = ∫0∞ 4πr² ρ2(r) dr
Teacher's Note: A spherical shell acts like a point charge outside, so the ball–shell energy is q1dq/4πε0l.
Exam Note: Sum over shells: result is the point-charge formula.
Question 131. A capacitor of capacitance C1 = 1.0 μF carrying initially a voltage V = 300 V is connected in parallel with an uncharged capacitor of capacitance C2 = 2.0 μF. Find the increment of the electric energy of this system by the moment equilibrium is reached. Explain the result obtained.
Solution.
The charge contained in the capacitor C1 is q = C1V and the energy stored in it is Ui = q²/(2C1) = ½C1V².
Now, when the capacitors are connected in parallel, the equivalent capacitance of the system is C = C1 + C2, and hence the energy stored in the system is
Uf = C1²V² / [2(C1 + C2)], as charge remains conserved during the process.
So the increment in the energy is
ΔU = (C1²V²/2) [1/(C1 + C2) − 1/C1] = −C1C2V² / [2(C1 + C2)] = −(1.0 × 2.0 × 10−12 × 9 × 104) / (2 × 3.0 × 10−6) J = −0.03 J = −30 mJ
Explanation: the lost energy is dissipated as heat (and radiation) in the connecting wires while the charge redistributes.
Corrected: the book prints −0.03 mJ; the numbers give −0.03 J = −30 mJ.
Teacher's Note: Charge is conserved on connection but energy is not; the deficit becomes Joule heat in the wires.
Exam Note: Evaluate in joules: answer −30 mJ.
Question 132. What amount of heat will be generated in the circuit shown in the figure (capacitors C, C0, C in parallel across the top, a battery of emf ξ in the bottom, and a switch Sw joining the lower plate of C0 to either terminal) after the switch Sw is shifted from position 1 to position 2?
Solution.
The charges on the capacitors in position 1 are as shown (q on the left C, q0 on C0, q + q0 on the right C). Here
q/C = q0/C0 = (q + q0)/(C + C0)
And (q + q0)[1/(C + C0) + 1/C] = ξ, or q + q0 = C(C + C0)ξ/(C0 + 2C)
Hence q = C²ξ/(C0 + 2C) and q0 = CC0ξ/(C0 + 2C).
After the switch is thrown to position 2, the charges change as shown (a charge q0 has flown in the right loop through the two capacitors and a charge q0 through the cell). Because of the symmetry of the problem there is no change in the energy stored in the capacitors. Thus
H (heat produced) = energy delivered by the cell = Δq ξ = q0ξ = CC0ξ² / (C0 + 2C)
(Figure not redrawn.)
Teacher's Note: Stored energy is unchanged by symmetry, so heat equals the battery work q0ξ.
Exam Note: Find q0 from the series-parallel charge split.
Question 133. What amount of heat will be generated in the circuit shown in the figure (a capacitor C with a switch Sw that connects it to battery ξ1 or ξ2 in the loop) after the switch Sw is shifted from position 1 to position 2?
Solution.
Initially, the charge on the right plate of the capacitor is q = C(ξ1 − ξ2) and finally, when switched to position 2, the charge on the same plate of the capacitor is q′ = Cξ1. So Δq = q′ − q = Cξ2.
From energy conservation, ΔU + heat liberated = Acell, where ΔU is the change in electrical energy:
½Cξ1² − ½C(ξ1 − ξ2)² + Heat liberated = Δq ξ1
As only the cell with emf ξ1 is responsible for the redistribution of the charge,
Cξ1ξ2 − ½Cξ2² + Heat liberated = Cξ2ξ1
Hence heat liberated = ½Cξ2²
(Figure not redrawn.)
Teacher's Note: Energy balance: battery work minus change in capacitor energy equals heat.
Exam Note: Only the cell that moves the charge does work.
Question 134. A system consists of two thin concentric metal shells of radii R1 and R2 with corresponding charges q1 and q2. Find the self-energy values W1 and W2 of each shell, the interaction energy of the shells W12, and the total electric energy of the system.
Solution.
The self-energy of each shell is given by qφ/2, where φ is the potential of the shell created only by the charge q on it. Hence the self-energies of shells 1 and 2 are
W1 = q1²/(8πε0R1) and W2 = q2²/(8πε0R2)
The interaction energy between the charged shells equals the charge q1 of the inner shell multiplied by the potential φ created by the other shell at the location of that charge (inside shell 2 the potential is constant):
W12 = q1 q2/(4πε0R2)
Hence the total energy of the system is
U = W1 + W2 + W12 = [1/(4πε0)] [q1²/(2R1) + q2²/(2R2) + q1q2/R2] (R1 < R2)
Teacher's Note: Self-energy is qφ/2 with only its own charge; mutual energy uses the outer shell's constant inner potential.
Exam Note: Mutual term is q1q2/4πε0R2, assuming R1 < R2.
Question 135. A charge q is distributed uniformly over the volume of a ball of radius R. Assuming the permittivity to be equal to unity, find: (a) the electrostatic self-energy of the ball; (b) the ratio of the energy W1 stored in the ball to the energy W2 pervading the surrounding space.
Solution.
Electric fields inside and outside the sphere with the help of Gauss's theorem:
E1 = qr/(4πε0R³) (r ≤ R), E2 = q/(4πε0r²) (r > R)
The sought self-energy of the ball is U = W1 + W2
= ∫0R (ε0E1²/2) 4πr² dr + ∫R∞ (ε0E2²/2) 4πr² dr = [q²/(8πε0R)] (1/5 + 1)
Hence, U = 3q²/(4πε0·5R) = 3q²/(20πε0R) and W1/W2 = 1/5.
Teacher's Note: Integrate ε0E²/2 over the volume inside (E∝r) and outside (E∝1/r²).
Exam Note: Inside gives 1/5 of the outside energy.
Question 136. A point charge q = 3.0 μC is located at the centre of a spherical layer of uniform isotropic dielectric with permittivity ε = 3.0. The inside radius of the layer is equal to a = 250 mm, the outside radius is b = 500 mm. Find the electrostatic energy inside the dielectric layer.
Solution.
The energy density is ½ε0εE², so the energy in a spherical layer is ∫½ε0εE² dV = ∫½εε0E² 4πr² dr. To find the electrostatic energy inside the dielectric layer, integrate this between the limits a and b, with E = q/(4πε0εr²):
U = ½ε0ε ∫ab [q/(4πε0εr²)]² 4πr² dr = [q²/(8πε0ε)] (1/a − 1/b) = 27 mJ
Teacher's Note: Use energy density ½ε0εE² with E = q/(4πε0εr²) only inside the dielectric layer.
Exam Note: Numbers: q = 3 μC, ε = 3 give 27 mJ.
Question 137. A spherical shell of radius R1 with uniform charge q is expanded to a radius R2. Find the work performed by the electric forces in this process.
Solution.
As the field is conservative, the total work done by the field force is
A = Ui − Uf = ½q(φ1 − φ2) = ½ · q²/(4πε0) (1/R1 − 1/R2) = [q²/(8πε0)] (1/R1 − 1/R2)
Teacher's Note: Work of electric forces = fall in self-energy q²/(8πε0R) as R grows.
Exam Note: Positive work: the shell is repelled outward.
Question 138. A spherical shell of radius R1 with a uniform charge q has a point charge q0 at its centre. Find the work performed by the electric forces during the shell expansion from radius R1 to radius R2.
Solution.
Initially, the energy of the system is Ui = W1 + W12, where W1 is the self-energy and W12 is the mutual energy. So
Ui = ½ · q²/(4πε0R1) + qq0/(4πε0R1)
and on expansion the energy of the system is
Uf = ½ · q²/(4πε0R2) + qq0/(4πε0R2)
The work done by the field force equals the decrement in the electrical energy:
A = Ui − Uf = [q(q0 + q/2)/(4πε0)] (1/R1 − 1/R2)
Alternate: upon expansion of the shell, the electric field (and hence the energy localized in it) changes only in the spherical layer R1 < r < R2. Hence
Ui − Uf = ∫R1R2 (ε0/2)(E1² − E2²) 4πr² dr
where, by Gauss's theorem, E1 = (q + q0)/(4πε0r²) and E2 = q0/(4πε0r²). As a result of integration,
A = [q(q0 + q/2)/(4πε0)] (1/R1 − 1/R2)
Teacher's Note: Add the point charge's mutual energy qq0/4πε0R to the shell's self-energy; take the difference.
Exam Note: Field changes only in the layer R1 to R2.
Question 139. A spherical shell is uniformly charged with the surface density σ. Using the energy conservation law, find the magnitude of the electric force acting on a unit area of the shell.
Solution.
The energy of the charged sphere of radius r is U = ½qφ = ½q · q/(4πε0r) = q²/(8πε0r).
If the radius of the shell changes by dr, the work done is
4πr²Fu dr = −dU = q²/(8πε0r²) dr
Thus the sought force per unit area is
Fu = q² / [4πr² · 8πε0r²] = (4πr²σ)² / [4πr² · 8πε0r²] = σ²/(2ε0)
Teacher's Note: Virtual work: force × dr equals the decrease −dU of the self-energy q²/8πε0r.
Exam Note: Result σ²/2ε0 equals the pressure on a charged conductor.
Question 140. A point charge q is located at the centre O of a spherical uncharged conducting layer provided with a small orifice. The inside and outside radii of the layer are equal to a and b respectively. What amount of work has to be performed to slowly transfer the charge q from the point O through the orifice and into infinity?
Solution.
Initially, there will be induced charges of magnitude −q and +q on the inner and outer surfaces of the spherical layer respectively. Hence the total electrical energy of the system is the sum of the self-energies of the spherical shells having radii a and b, and their mutual energies including the point charge q:
Ui = ½ · q²/(4πε0b) + ½ · (−q)²/(4πε0a) + (−q)q/(4πε0a) + qq/(4πε0b) + (−q)q/(4πε0b)
or Ui = [q²/(8πε0)] (1/b − 1/a)
Finally, the charge q is at infinity, hence Uf = 0.
Now, the work done by the agent = increment in the energy = Uf − Ui = [q²/(8πε0)] (1/a − 1/b)
(Figure not redrawn.)
Teacher's Note: Energy before: induced shells' self-energies plus mutual terms; after: all zero, work equals the rise in energy.
Exam Note: Positive: work is done against attraction.
Question 141. Each plate of a parallel-plate air capacitor has an area S. What amount of work has to be performed to slowly increase the distance between the plates from x1 to x2 if (a) the charge of the capacitor, which is equal to q, or (b) the voltage across the capacitor, which is equal to V, is kept constant in the process?
Solution.
(a) The sought work is equivalent to the work performed against the electric field created by one plate, holding it at rest and bringing the other plate away. Therefore the required work is Aagent = qE(x2 − x1), where E = σ/(2ε0) is the intensity of the field created by one plate at the location of the other. So
Aagent = q · σ/(2ε0) (x2 − x1) = [q²/(2ε0S)] (x2 − x1)
Alternate: Aext = ΔU (as the field is potential) = q²x2/(2ε0S) − q²x1/(2ε0S) = [q²/(2ε0S)](x2 − x1)
(b) When the voltage is kept constant, the force acting on each plate depends on the distance between the plates. So the elementary work done by the agent in displacing a plate over a distance dx relative to the other is dA = −Fx dx, where
Fx = −[σ(x)/(2ε0)] S σ(x) and σ(x) = ε0V/x
Hence A = ∫dA = ∫x1x2 ½ε0SV²/x² dx = (ε0SV²/2) (1/x1 − 1/x2)
Alternate: from energy conservation, Uf − Ui = Acell + Aagent, i.e.
½(ε0S/x2)V² − ½(ε0S/x1)V² = [ε0S/x2 − ε0S/x1]V² + Aagent
(as Acell = (qf − qi)V = (Cf − Ci)V²). So
Aagent = (ε0SV²/2) (1/x1 − 1/x2)
Teacher's Note: At constant charge the force is constant; at constant voltage the battery also does work, so use energy conservation.
Exam Note: In (b) include the battery's work Acell.
Question 142. Inside a parallel-plate capacitor there is a plate parallel to the outer plates, whose thickness is equal to η = 0.60 of the gap width. When the plate is absent the capacitor capacitance equals C = 20 nF. First, the capacitor was connected in parallel to a constant voltage source producing V = 200 V, then it was disconnected from it, after which the plate was slowly removed from the gap. Find the work performed during the removal, if the plate is (a) made of metal; (b) made of glass.
Solution.
(a) When a metal plate of thickness ηd is inserted inside the capacitor, the capacitance of the system becomes C0 = ε0S/[d(1 − η)] = C/(1 − η).
Initially the charge on the capacitor is q0 = C0V = ε0SV/[d(1 − η)]. Finally, the capacitance of the capacitor is C = ε0S/d. As the source is disconnected, the charge on the plates remains the same during the process.
From energy conservation, Uf − Ui = Aagent (as the cell does no work), or
Aagent = ½q0²/C − ½q0²/C0 = ½ [ε0SV/(d(1 − η))]² [1/C − (1 − η)/C] = ½ CV²η/(1 − η)² = 1.5 mJ
(b) Initially, the capacitance of the system with the glass plate is C0 = Cε/[η(1 − ε) + ε] (the capacitance of two capacitors in series, the glass plate of permittivity ε and the air gap). So the charge on the plates is q0 = C0V. The capacitance after the glass plate has been removed equals C. From energy conservation,
Aagent = Uf − Ui = ½q0² (1/C − 1/C0) = ½ CV² εη(ε − 1) / [ε − η(ε − 1)]² = 0.8 mJ
(The book's number 0.8 mJ corresponds to taking ε = 6 for glass; ε is not stated in the problem. Check: with ε = 6, εη(ε−1) = 18 and [ε − η(ε−1)]² = 9, so A = ½ × 20 nF × (200 V)² × 2 = 0.8 mJ.)
Teacher's Note: Source disconnected means q constant; work equals the rise in q²/2C when the slab is removed.
Exam Note: State ε of glass (6) to get 0.8 mJ.
Question 143. A parallel-plate capacitor was lowered into water in a horizontal position, with water filling up the gap between the plates d = 1.0 mm wide. Then a constant voltage V = 500 V was applied to the capacitor. Find the water pressure increment in the gap.
Solution.
When the capacitor immersed in water is connected to a constant voltage source, it gets charged. Suppose σ0 is the free charge density on the capacitor plates. Because water is a dielectric, bound charges also appear in it; let σ′ be the surface density of bound charges. (Because of the homogeneity of the medium and uniformity of the field, ignoring edge effects, no volume density of bound charges exists.) The electric field due to free charges only is σ0/ε0; that due to bound charges is σ′/ε0, and the total electric field is σ0/(εε0). Recalling that the sign of bound charges is opposite to that of the free charges, we have
σ0/(εε0) = σ0/ε0 − σ′/ε0, or σ′ = [(ε − 1)/ε] σ0
Because of the field that exists due to the free charges (not the total field; the field due to the bound charges must be excluded as it only gives rise to self-energy effects), there is a force attracting the bound charges to the nearby plates. This force is
½σ′ · σ0/ε0 = (ε − 1)σ0² / (2εε0) per unit area.
The factor ½ needs an explanation. Normally the force on a test charge is qE in an electric field E. But if the charge itself is produced by the electric field, then the force must be built up bit by bit: F = ∫0E q(E′) dE′, and if q(E′) ∝ E′ then F = ½ q(E) E. The same factor ½ appears, for example, in the energy per unit volume of a linear dielectric in an electric field, −½ P·E0, where P is the polarization vector (dipole moment per unit volume).
The force per unit area manifests itself as excess pressure of the liquid. Noting that V/d = σ0/(εε0), we get
Δp = ε0ε(ε − 1)V² / (2d²)
Substitution, using ε = 81 for water, gives Δp = 7.17 kPa = 0.07 atm.
Teacher's Note: Bound charges feel only the free-charge field, with a factor ½; with V/d = σ0/εε0 this gives the pressure.
Exam Note: Remember ε = 81 for water; answer about 7 kPa.
Question 144. A parallel-plate capacitor is located horizontally so that one of its plates is submerged into liquid while the other is over its surface (see figure). The permittivity of the liquid is equal to ε, its density is equal to ρ. To what height will the level of the liquid in the capacitor rise after its plates get a charge of surface density σ?
Solution.
One way of doing this problem is exactly as in the previous problem, so let us try an alternative method based on energy. Suppose the liquid rises by a distance h. Then calculate the extra energy of the liquid as the sum of polarization energy and the ordinary gravitational energy. The latter is ½h · ρg · Sh = ½ρgSh².
If σ is the free charge surface density on the plate, the bound charge density is, from the previous problem, σ′ = [(ε − 1)/ε] σ. This is also the volume density of induced dipole moment, i.e. polarization. Then the polarization energy density is, as before,
−½σ′E0 = −½σ′ σ/ε0 = −(ε − 1)σ² / (2ε0ε)
and the total polarization energy is −S(a + h)(ε − 1)σ²/(2ε0ε), where a is the initial depth of liquid between the plates.
Then the total energy is
U(h) = −S(a + h)(ε − 1)σ²/(2ε0ε) + ½ρgSh²
The actual height to which the liquid rises is determined from dU/dh = U′(h) = 0. This gives
h = (ε − 1)σ² / (2ε0ερg)
(Figure not redrawn.)
Teacher's Note: Minimise polarization-plus-gravitational energy U(h); the equilibrium condition U′(h) = 0 gives h.
Exam Note: Gravity term is ½ρgSh² for raising a column.
Question 145. A cylindrical layer of dielectric with permittivity ε is inserted into a cylindrical capacitor to fill up all the space between the electrodes. The mean radius of the electrodes equals R, the gap between them is equal to d, with d ≪ R. The constant voltage V is applied across the electrodes of the capacitor. Find the magnitude of the electric force pulling the dielectric into the capacitor.
Solution.
We know that the energy of a capacitor is U = q²/(2C). Hence Fx = ∂U/∂x at constant q, so we have
Fx = (q²/2)(∂C/∂x)/C² (1)
Now, since d ≪ R, the capacitance of the given capacitor can be calculated by the formula of a parallel-plate capacitor. Therefore, if the dielectric is introduced up to a depth x and the length of the capacitor is l, we have
C = 2πε0εRx/d + 2πRε0(l − x)/d (2)
From (1) and (2), with q = CV, we get
Fx = ½V² ∂C/∂x = ε0(ε − 1) πRV²/d
Teacher's Note: Treat the capacitor as two parallel pieces (filled and empty); force is ½V² dC/dx at fixed V.
Exam Note: Constant q and constant V give the same force.
Question 146. A capacitor consists of two stationary plates shaped as a semi-circle of radius R and a movable plate made of dielectric with permittivity ε and capable of rotating about an axis O between the stationary plates (see figure). The thickness of the movable plate is equal to d, which is practically the separation between the stationary plates. A potential difference V is applied to the capacitor. Find the magnitude of the moment of forces relative to the axis O acting on the movable plate in the position shown in the figure.
Solution.
When the capacitor is kept at a constant potential difference V, the work performed by the moment of electrostatic forces between the plates when the inner movable plate is rotated by an angle dφ equals the increase in the potential energy of the system. This comes about because charges flow from the battery to keep the potential constant, and the work done by these charges is twice in magnitude and opposite in sign to the change in the energy of the capacitor. Thus
Nz = ∂U/∂φ = ½V² ∂C/∂φ
Now the capacitor can be thought of as made up of two parts (with and without the dielectric) in parallel. Using that the area of a sector of angle φ is ½R²φ,
C = ε0R²φ/(2d) + ε0ε(π − φ)R²/(2d)
Differentiation then gives
Nz = −(ε − 1)ε0R²V²/(4d)
The negative sign of Nz indicates that the moment of the force acts clockwise (i.e. tries to pull the dielectric in). The magnitude is (ε − 1)ε0R²V²/(4d).
(Figure not redrawn.)
Teacher's Note: Write C as air sector plus dielectric sector in parallel; torque = ½V² dC/dφ at fixed V.
Exam Note: Give magnitude; the sign only shows direction.
Step-by-Step IE Irodov Solutions for JEE Math
Download IE Irodov Solutions for JEE
Review detailed solutions for JEE Mathematics. The IE Irodov Solutions Chapter 18 Electric Capacitance Energy Of An Electric Field PDF provides comprehensive answers mapped to standard IE Irodov Solutions textbooks, ensuring targeted revision for weekly tests and terminal exams.
Step-by-Step Mathematical Explanations
Each problem includes a step-by-step breakdown to clarify complex mathematical formulas and theorems. Utilizing these verified answers ensures students learn the proper problem-solving techniques expected in standard academic assessments.
Next Steps in Your Mathematics Revision
In addition to these IE Irodov Solutions chapters, students can explore a wider library of free online mock tests, printable sample papers, and short revision notes aligned with the 2026 academic session.
FAQs
They are chapter-wise solved questions from the IE Irodov book for JEE Physics. Each answer is explained step by step so you can check your work and revise.
Yes. All chapters can be read online for free on a phone, tablet or computer, and no sign-up is needed.
Try each question on your own first, then read the solution. Use it to check your steps, correct mistakes and learn how a full answer is written.
Regular practice improves accuracy and speed and shows which topics need more revision. It works best alongside your textbook and class notes.
Yes. The chapter list on this page links to every chapter’s solved questions, so you can open the topic you are studying.
They are listed for the 2026-27 session. Check that the questions match the textbook edition you use.