Read and download free pdf of CBSE Class 10 Science Electricity Worksheet. Students and teachers of Class 10 Science can get free printable Worksheets for Class 10 Science Chapter 12 Electricity in PDF format prepared as per the latest syllabus and examination pattern in your schools. Class 10 students should practice questions and answers given here for Science in Class 10 which will help them to improve your knowledge of all important chapters and its topics. Students should also download free pdf of Class 10 Science Worksheets prepared by school teachers as per the latest NCERT, CBSE, KVS books and syllabus issued this academic year and solve important problems with solutions on daily basis to get more score in school exams and tests
Worksheet for Class 10 Science Chapter 12 Electricity
Class 10 Science students should refer to the following printable worksheet in Pdf for Chapter 12 Electricity in Class 10. This test paper with questions and answers for Class 10 will be very useful for exams and help you to score good marks
Class 10 Science Worksheet for Chapter 12 Electricity
Question. A letter A is constructed of a uniform wire of resistance 1 ohm per cm. The sides of the letter are 20 cm and the cross piece in the middle is 10 cm long. The resistance between the ends of the legs will be
(a) 32.4 ohm
(b) 28.7 ohm
(c) 26.7 ohm
(d) 24.7 ohm
Answer : C
Question. Three resistances of 2, 3 and 5 W are connected in parallel to a 10 V battery of negligible internal resistance. The potential difference across the 3 W resistance will be
(a) 2 V
(b) 3 V
(c) 5 V
(d) 10 V
Answer : D
Question. You are given n identical wires, each of resistance R. When these are connected in parallel, the equivalent resistance is X. When these will be connected in series, then the equivalent resistance will be
(a) X/n2
(b) n2X
(c) X/n
(d) nX
Answer : B
Question. 20 coulomb charge is flowing in 0.5 second from a point in an electric circuit then value of electric current in amperes will be
(a) 10
(b) 40
(c) 0.005
(d) 0.05
Answer : B
Question. A cylindrical rod is reformed to twice its length with no change in its volume. If the resistance of the rod was R, the new resistance will be
(a) R
(b) 2R
(c) 4R
(d) 8R
Answer : C
Question. A piece of wire of resistance R is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination isRl, then the ratio R/Rl is
(a) 1/25
(b) 1/5
(c) 5
(d) 25
Answer : D
Question. 2 ampere current is flowing through a conductor from a 10 volt emf source then resistance of conductor is
(a) 20 W
(b) 5 W
(c) 12 W
(d) 8 W
Answer : B
Question. Three resistors of 4.0 W , 6.0 W and 10.0 W are connected in series. What is their equivalent resistance
(a) 20 W
(b) 7.3 W
(c) 6.0 W
(d) 4.0 W
Answer : C
Question. Two unequal resistances are connected in parallel. Which of the following statement is true
(a) current in same in both
(b) current is larger in higher resistance
(c) voltage-drop is same across both
(d) voltage-drop is lower in lower resistance
Answer : C
Question. A wire of resistance R is cut into ten equal parts which are then joined in parallel. The new resistance is
(a) 0.01 R
(b) 0.1 R
(c) 10 R
(d) 100 R
Answer : A
Question. A 24 V potential difference is applied is applied across a parallel combination of four 6 ohm resistor. The current in each resistor is
(a) 1 A
(b) 4 A
(c) 16 A
(d) 36 A
Answer : B
Question. A student carries out an experiment and plots the V-I graph of three samples of nichrome wire with resistances R1, R2 and R3 respectively (Figure).
Which of the following is true?
(a) R1 > R2 = R3
(b) R1 > R2 > R3
(c) R3 > R2 = R1
(d) R2 > R3 > R1
Answer : C
Question. A current of 4.8 A is flowing in a conductor. The number of electrons passing per second through the conductor will be
(a) 3 x 1020
(b) 76.8 x 1020
(c) 7.68 x 10-19
(d) 3 x 1019
Answer : D
Question. How much work is done in moving a charge of 2 C from a point of 118 V to a point of 128 V?
(a) 20 J
(b) 30 J
(c) 40 J
(d) 10 J
Answer : A
Question. Two bulbs have the following ratings:
1. 40 W, 220 V
2. 20 W, 100 V
The ratio of their resistance is
(a) 1: 2
(b) 2 :1
(c) 1:1
(d) 1: 3
Answer : B
Question. A current of 1 A is drawn by a filament of an electric bulb. Number or electrons passing through a cross section of the filament in 16 seconds would be roughly
(a) 1020
(b) 1016
(c) 1018
(d) 1023
Answer : A
Question. If a wire of resistance R is melted and recast to half of its length, the new resistance of the wire will be
(a) R/4
(b) R/2
(c) R
(d) 2R
Answer : A
Question. A circular conductor is made of a uniform wire of resistance 2x10-3 ohm/metre and the diameter of this circular conductor is 2 metres. Then the resistance measured between the ends of the diameter is (in ohms)
(a) p x 10-3
(b) 2p x 10-3
(c) 4p x 10-3
(d) 4x 10-3
Answer : C
Question. The length of a wire is doubled. By what factor does the resistance change
(a) 4 time as large
(b) twice as large
(c) unchanged
(d) half as large
Answer : D
Question. An electric kettle consumes 1 kW of electric power when operated at 220 V. A fuse wire of what rating must be used for it?
(a) 1 A
(b) 2 A
(c) 4 A
(d) 5 A
Answer : D
Question. A piece of wire of resistance R is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination is R’, then the ratio R/R’ is:
a. 125
b. 15
c. 5
d. 25
Answer : D
Fill in The Blank
Question. Fuse wire has a ......... melting point and is made of an alloy of ......... and ......... If the current in a circuit rises too high, the fuse wire .........
Answer : Low, lead, tin, melts
Question. In a parallel circuit, each circuit, each circuit element has the same ..........
Answer : Potential difference
Question. The .......... reaction within the cell generates the potential difference between its two terminals that sets the .......... in motion to flow the current through a resistor.
Answer : chemical
Question. ......... is a property that resists the flow of electrons in a conductor.
Answer : Resistance
Question. Power transmission is carried out at high .......... and low ........ .
Answer : Voltage, current
Question. The S.I. unit of electric current is ..........
Answer : Ampere
Question. The S.I. unit of resistance is ..........
Answer : Ohm (W )
Question. Rate at which electric work is done is called .........
Answer : Electric power
Question. The rate of flow of electric charge is called ..........
Answer : Current
Question. Electric energy is produced by the ........ of charges.
Answer : Separation
Question. Potential difference is a .......... quantity.
Answer : Scalar
Question. Two resistances of 2 W each are connected in parallel. The equivalent resistance is .......... .
Answer : 1 W
Assertion and Reason
DIRECTION : In the following questions, a statement of assertion (A) is followed by a statement of reason (R). Mark the correct choice as:
(a) Both assertion (A) and reason (R) are true and reason (R) is the correct explanation of assertion (A).
(b) Both assertion (A) and reason (R) are true but reason (R) is not the correct explanation of assertion (A).
(c) Assertion (A) is true but reason (R) is false.
(d) Assertion (A) is false but reason (R) is true.
(e) Both Assertion and Reason are false.
Question. Assertion : When the resistances are connected between the same two points, they are said to be connected in parallel.
Reason : In case the resistance is to be decreased, then the individual resistances are connected in parallel.
Answer : B
Question. Assertion : When the length of a wire is doubled, then its resistance also gets doubled.
Reason : The resistance of a wire is directly proportional to its length.
Answer : A
Question. Assertion : A torch bulb give light if operated on AC of same voltage and current as DC.
Reason : Heating effect is common to both AC and DC.
Answer : A
Question. Assertion : In a simple battery circuit the point of lowest potential is positive terminal of the battery.
Reason : The current flows towards the point of the lower potential as it flows in such a circuit from the negative to the positive terminal.
Answer : D
Question. Assertion : 40 W tube light give more light in comparison to 40 w bulb.
Reason : Light produced is same from same power.
Answer : D
Question. Assertion: Tungsten metal is used for making filaments of incandescent lamps.
Reason : The melting point of tungsten is very low.
Answer : C
Question. Assertion : A resistor of resistance R is connected to an ideal battery. If the value of R is decreased, the power dissipated in the circuit will increase.
Reason : The power dissipated in the circuit will increase.
Answer : C
Question. Assertion : Resistance of 50 W bulb is greater than that of 100 W.
Reason : Resistance of bulb is inversely proportional to rated power.
Answer : B
Question. Assertion : A tube light emits white light.
Reason : Emission of light in a tube takes place at a very high temperature
Answer : C
Question. Assertion : Insulators do not allow flow of current through themselves.
Reason : They have no free-charge carriers.
Answer : A
Very Short Answers :
Question. What does an electric circuit mean?
Answer : A continuous and closed path of an electric current is called an electric circuit. An electric circuit consists of electric devices, source of electricity and wires that are connected with the help of a switch.
Question. The radius of conducting wire is doubled. What will be the ratio of its new specific resistance to the old one?
Answer: 1 : 1, specific resistance does not change as it depends on the nature of material only.
Question. How are bulbs connected in a fairy light circuit used for decoration of buildings in festivals ?
Answer: Series combination.
Question. What will happen to the resistivity of a wire of length L if it is cut into three parts?
Answer: Resistivity of the wire will not change even when the wire is cut into three parts as resistivity is a characteristic of the material of the conductor and does not depend on the physical dimensions of the conductor.
Question. What is the mistake in the circuit given below ? 
Answer: The terminals of ammeter are wrongly connected.
Question. What determines the rate at which energy is delivered by a current?
Answer: Electric power is the rate at which energy is delivered by a current
Question. Name the type of current used in household supply.
Answer: Alternate current
Question. A bulb gets dimmer when an electric iron or geyser is switched on, why?
Answer: It is because electric iron or geyser draws heavy current from the circuit, takes heavy power and therefore bulb becomes dimmer due to decrease in voltage
Question. Write the relationship between heat energy produced in a conductor when potential difference V is applied across its terminals and a current, I flows through it for the time ‘t’.
Answer: H = VIt
Question. Why heat is produced when current is passed through a conductor?
Answer: The electrons collide with each other while moving and loses some kinetic energy which is converted into heat energy.
Question. Why are heating elements made of alloys rather than metals?
OR
Why are alloys commonly used in electrical heating devices like toasters and electric iron? Give reason.
Answer: Alloys have high resistivity/high melting point/alloys do not oxidise (or burn readily at high temperatures).
Question. Identify the X, Y and Z in the circuit given below : 
Answer: X = Ammeter, Y = Rheostat, Z = Voltmeter.
Question. If two resistors in series have ‘p’ number of common points. What will be the value of ‘p’?
Answer: One.
Question.The resistance of a wire of length 150 cm and of uniform area of cross-section 0.015 cm2, is found to be 3.0 W. Calculate the specific resistance of the wire.
Answer: Here, l = 150 cm; A = 0.015 cm2; R = 3.0 W.
Specific resistance, r = RA/1
= 3.0 X 0.015/150
= 0·0003 W cm.
Question. Define resistance of a conductor.
Answer: The obstruction offered to the flow of current by a conductor is called its resistance.
Question. State Ohm’s law.
Answer: According to Ohm’s law, the current flowing in a conductor is directly proportional to the potential difference applied across its ends, provided the temperature and other physical conditions of the conductor remain constant.
Question. Define resistivity.
Answer: The resistivity of a substance is numerically equal to the resistance of a rod of that substance which is 1 metre long and 1 square metre in cross-section.
Question. Define the unit of current.
Answer : The unit of electric current is ampere (A). 1 A is defined as the flow of 1 C of charge through a wire in 1 s.
Question. Will current flow more easily through a thick wire or a thin wire of the same material, when connected to the same source? Why?
Answer : The current will flow more easily through thick wire. It is because the resistance of a conductor is inversely proportional to its area of cross - section. If thicker the wire, less is resistance and hence more easily the current flows.
Question. Name a device that helps to maintain a potential difference across a conductor.
Answer : Any source of electricity like battery, cell, power supply, etc. helps to maintain a potential difference across a conductor.
Question. What is meant by saying that the potential difference between two points is 1 V?
Answer : If 1 J of work is required to move a charge of amount 1 C from one point to another, then it is said that the potential difference between the two points is 1 V.
Question. Mention the conditions under which current can flow in a conductor?
Answer : a) Circuit is closed b) There is a potential difference along the conductor.
Question. How will be the resistance of a conductor change if its area is doubled?
Answer : Resistance will become half as R is inversely proportional to area.
Question. When do we say that potential difference between two points in a circuit is 1 volt?
Answer : When 1 joule of work is done to move a charge of 1 coulomb from one point to the other
Question. What is the resistance of an ideal voltmeter?
Answer : Infinite
Question. What is the amount of charge when a current of 4A flows in a circuit for 10 minutes?
Answer : Q = I x t = 4x 10x 60 = 2400C
Short Answers :
Question. V-I graph for two wires A and B are shown in the figure. If both wires are of same length and same thickness, which of the two is made of a material of high resistivity? Give justification for your answer.
Answer : Greater than slope of V-I graph, greater will be the resistance of given metallic wire. In the given graph, wire A has greater slope then B. Hence, wire A has greater resistance. For the wires of same length and same thickness, resistance depends on the nature of material of the wire, i.e.
Question. A wire of resistance 20 Ω is bent to form a closed square. What is the resistance across a diagonal of the square?
Answer :
Question. Calculate the number of electrons constituting one coulomb of charge.
Answer : One electron possesses a charge of 1.6 ×10-19C, i.e., 1.6 ×10-19C of charge is contained in 1 electron.
∴ 1 C of charge is contained in 1/1.6 x 10-19 = 6.25 x 1018 = 6 x 1018
Therefore, 6 x 1018 electrons constitute one coulomb of charge.
Question. Explain the role of fuse wire connected in series with any electrical appliance in an electric circuit.
Why should a fuse with a defined rating for an electric circuit not be replaced by the one with a larger rating?
Answer : Fuse wire is a safety device connected in series with the live wire of the circuit, since it has high resistivity and low melting point. It melts when a sudden urge of large current passes through it and disconnects the entire circuit from the electrical supply. But in case if we use a larger rating fuse wire instead of a defined rating fuse wire then it will not protect the circuit as high current will easily pass through it and it will not melt.
Question. Which uses more energy, a 250 W TV set in 1 hr, or a 1200 W toaster in 10 minutes?
Answer : Energy consumed by 250 W TV in 1 h = 250 × 1 = 250 W h
Energy consumed by 1200 W toaster in 10 minutes = 1200 x 10/60 = 200 W h
Here total energy consumed by the TV is more than toaster
Question. Why does the cord of an electric heater not glow while the heating element does?
Answer : The cord of the electric heater is made up of copper or aluminium which has lower resistance and higher conductance, therefore very less heat energy is produced.
Heating element is made up of alloys which have high resistance and lot of heat is produced, and only a little amount of electric energy makes it to glow
Long Answers :
Question. A. Two identical wires one of nichrome and other of copper are connected in series and a current (I) is passed through them. State the change observed in the temperatures of the two wires. Justify your answer. State the law which explains the above observation.
B. An electric bulb is rated at 60 W, 240 V. Calculate its resistance. If the voltage drops to 192 V, calculate the power consumed and the current drawn by the bulb. (Assume that the resistance of the bulb remains unchanged.)
Answer : A. The resistivity of nichrome is more than that of copper so its resistance is also high. Therefore, large amount of heat is produced in the nichrome wire for the same current as compared to that of copper wire. Accordingly, more change in temperature is observed in the nichrome wire. This is explained by Joule’s law of heating. Joule’s law of heating: It states that the amount of heat produced in a conductor is
Question. How much energy is given to each coulomb of charge passing through a 6 V battery?
Answer : The energy given to each coulomb of charge is equal to the amount of work which is done in moving it.
Now we know that,
Potential difference = Work Done/Charge
∴ Work done = Potential difference × charge
Where, Charge = 1 C and Potential difference = 6 V
∴ Work done = 6×1
= 6 Joule.
Question. On what factors does the resistance of a conductor depend?
Answer : The resistance of a conductor depends upon the following factors:
→ Length of the conductor
→ Cross-sectional area of the conductor
→ Material of the conductor
→ Temperature of the conductor
| CBSE Class 10 Chemistry Chemical Reactions And Equations Worksheet Set A |
| CBSE Class 10 Chemistry Chemical Reactions And Equations Worksheet Set B |
| CBSE Class 10 Science Acids Bases And Salts Worksheet Set A |
| CBSE Class 10 Science Acids Bases And Salts Worksheet Set B |
| CBSE Class 10 Chemistry Metals And Non Metals Worksheet Set A |
| CBSE Class 10 Chemistry Metals And Non Metals Worksheet Set B |
| CBSE Class 10 Physics Electricity Worksheet |
| CBSE Class 10 Science Electricity Worksheet |
| CBSE Class 10 Science Sources Of Energy Worksheet |
| CBSE Class 10 Science Sustainable Management of Natural Resources Worksheet |
| CBSE Class 10 Chemistry Revision Worksheet Set D |
| CBSE Class 10 Science Collection Of Important Questions Worksheet |
| CBSE Class 10 Science Physics Worksheet Set A |
More Study Material
CBSE Class 10 Science Chapter 12 Electricity Worksheet
We hope students liked the above worksheet for Chapter 12 Electricity designed as per the latest syllabus for Class 10 Science released by CBSE. Students of Class 10 should download in Pdf format and practice the questions and solutions given in the above worksheet for Class 10 Science on a daily basis. All the latest worksheets with answers have been developed for Science by referring to the most important and regularly asked topics that the students should learn and practice to get better scores in their class tests and examinations. Studiestoday is the best portal for Class 10 students to get all the latest study material free of cost.
Worksheet for Science CBSE Class 10 Chapter 12 Electricity
Expert teachers of studiestoday have referred to the NCERT book for Class 10 Science to develop the Science Class 10 worksheet. If you download the practice worksheet for one chapter daily, you will get higher and better marks in Class 10 exams this year as you will have stronger concepts. Daily questions practice of Science worksheet and its study material will help students to have a stronger understanding of all concepts and also make them experts on all scoring topics. You can easily download and save all revision worksheet for Class 10 Science also from www.studiestoday.com without paying anything in Pdf format. After solving the questions given in the worksheet which have been developed as per the latest course books also refer to the NCERT solutions for Class 10 Science designed by our teachers
Chapter 12 Electricity worksheet Science CBSE Class 10
All worksheets given above for Class 10 Science have been made as per the latest syllabus and books issued for the current academic year. The students of Class 10 can be rest assured that the answers have been also provided by our teachers for all worksheet of Science so that you are able to solve the questions and then compare your answers with the solutions provided by us. We have also provided a lot of MCQ questions for Class 10 Science in the worksheet so that you can solve questions relating to all topics given in each chapter. All study material for Class 10 Science students have been given on studiestoday.
Chapter 12 Electricity CBSE Class 10 Science Worksheet
Regular worksheet practice helps to gain more practice in solving questions to obtain a more comprehensive understanding of Chapter 12 Electricity concepts. Worksheets play an important role in developing an understanding of Chapter 12 Electricity in CBSE Class 10. Students can download and save or print all the worksheets, printable assignments, and practice sheets of the above chapter in Class 10 Science in Pdf format from studiestoday. You can print or read them online on your computer or mobile or any other device. After solving these you should also refer to Class 10 Science MCQ Test for the same chapter.
Worksheet for CBSE Science Class 10 Chapter 12 Electricity
CBSE Class 10 Science best textbooks have been used for writing the problems given in the above worksheet. If you have tests coming up then you should revise all concepts relating to Chapter 12 Electricity and then take out a print of the above worksheet and attempt all problems. We have also provided a lot of other Worksheets for Class 10 Science which you can use to further make yourself better in Science
You can download the CBSE Printable worksheets for Class 10 Science Chapter 12 Electricity for latest session from StudiesToday.com
Yes, you can click on the links above and download Printable worksheets in PDFs for Chapter 12 Electricity Class 10 for Science
Yes, the Printable worksheets issued for Class 10 Science Chapter 12 Electricity have been made available here for latest academic session
You can easily access the links above and download the Class 10 Printable worksheets Science Chapter 12 Electricity for each chapter
There is no charge for the Printable worksheets for Class 10 CBSE Science Chapter 12 Electricity you can download everything free
Regular revision of practice worksheets given on studiestoday for Class 10 subject Science Chapter 12 Electricity can help you to score better marks in exams
Yes, studiestoday.com provides all latest NCERT Chapter 12 Electricity Class 10 Science test sheets with answers based on the latest books for the current academic session
Yes, studiestoday provides worksheets in Pdf for Chapter 12 Electricity Class 10 Science in mobile-friendly format and can be accessed on smartphones and tablets.
Yes, worksheets for Chapter 12 Electricity Class 10 Science are available in multiple languages, including English, Hindi